Numark Industries PRO TT-1 Turntable User Manual
Contents
1. approximately balanced horizontally floats freely 28 Tone Arm Height Adjust This allows the tone arm to be properly align with the platter surface E l 29 Height Lock Prevents accidental adjustment if the t height 30 Counterweight Adjustment creates the proper 5 Refasten the tonearm with the arm clamp downward pressure of the stylus to the record Attach now by sliding the counterweight onto the rear of the 6 Hold the counterweight stationary tonearm Twist it lightly and it will screw onto the rear shaft with one hand and rotate only the xX of the tonearm stylus pressure ring to bring the N 4 number O of the ring into alignment NE with the center line on the tonearm Tonea AAN rae rear shaft 7 Rotate the counterweight with scale ring clockwise to the correct stylus pressure following the ij The following explains proper counterweight and manufacture s recommendation anti skating set up Cartridge manufacturers usually specify the proper settings Note Failure to follow recommended stylus pressure can damage both the stylus and record This can also 1 Remove the stylus protector do not touch the seriously degrade performance stylus tip during the adjustment 8 Set the anti skating control knob 27 to the same 2 Set the cueing lever to the lower position so it does value as the stylus pressure unless your manufacturer not effect tone arm height spec2. external voltage selector switches if any should only be reset and re equipped with a proper plug for alternative voltage by a qualified service technician Do not attempt to alter this yourself NOTE This apparatus does not exceed the Class A Class B whichever is applicable limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications WARNING To reduce the risk of fire or electric shock do not expose this appliance to moisture Electrical equipment should NEVER be kept or stored in damp environments Please record the serial number of your unit as shown on the back of the chassis as well as the name of the l dealer from whom you purchased the unit Retain this information for your records Please return the warranty card enclosed to register your product with us MODEL PRO TT 1 SERIAL NUMBER I I PURCHASED FROM I DATE OF PURCHASI I Numark The Leader in DJ Technology 1999 Numark Industries 2 htto www numark com PRO TT 1 Numark PRO TT 1 Professional Turntable INDEX Safety Information Page 2 Product Registration System Precautions Page 4 Introduction Page 5 Features and Assembly Instructions Page 6 Operating Instructions Page 10 Routine Maintenance Specifications Page 11 Warranty and Service Page 12 Contents of this package Please check outer packing material for hidden parts 11 Ma
3. repairing any product or replace a product with a rebuilt reconditioned or new product Repaired mixers will be warranted for a period equal to the remainder of the original Limited Warranty on the original mixer or for 90 days whichever is longer All replaced parts components boards and equipment become the property of NUMARK If NUMARK determines that any mixer is not covered by this Limited Warranty purchaser must pay all parts shipping and labor charges for the repair or return of such mixer 4 What are the limits on NUMARKSS liabilities THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY TOGETHER WITH ANY IMPLIED WARRANTIES COVERING NUMARK MIXERS INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW NUMARK SHALL NOT BE LIABLE FOR ANY SPECIAL INCIDENTAL CONSEQUENTIAL INDIRECT OR SIMILAR DAMAGES LOSS OF PROFITS DAMAGES TO PURCHASER S PROPERTY OR INJ URY TO PURCHASER OR OTHERS ARISING OUT OF THE USE MISUSE OR INABILITY TO USE ANY NUMARK MIXER BREACH OF WARRANTY OR NEGLIGENCE INCLUDING BUT NOT LIMITED TO NUMARK S OWN NEGLIGENCE EVEN IF NUMARK OR ITS AGENT HAS BEEN ADVISED OF SUCH DAMAGES OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK S MIXERS AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES THIS LIMITED WARRANTY SH
4. ALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER S EXCLUSIVE REMEDY IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS This Limited Warranty allocates risk of product failure between purchaser and NUMARK and NUMARK S product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty The agents employees distributors and dealers of NUMARK are not authorized to make modifications to this Limited Warranty or make additional warranties binding on NUMARK Accordingly additional statements such as dealer advertising or presentation whether oral or written do not constitute warranties by NUMARK and should not be relied upon 5 How does state law apply to this warranty SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER This Limited Warranty gives you specific legal rights You may also have other rights which vary from one jurisdiction to another RETURN INFORMATION 1 A Return Authorization number must be obtained from Numark throug
5. Numark Professional Disc Jockey Products PRO TT 1 PROFESSIONAL DIRECT DRIVE TURNTABLE OW NER S MANUAL Lit ype 1999 Numark INDUSTRIES 11 Helmsman Avenue North Kingstown RI 02852 http www numark com PRO TT 1 Safety Information and Product Registration CAUTION Dn RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying this appliance CAUTION FOR USA amp CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE SAFETY INSTRUCTIONS 1 Read Instructions All the safety and operating instructions should be read before this product is connected and used 2 Retain I
6. al Direct drive 12 Pole 3 Phase Brushless DC Motor Aluminum diecast 330mm dia 3341 3 45 and 78 rpm 10 more than 2 2kgf cm Electronic 0 13 50dB DIN B 2 3dB 1 7 3 5 mV 16dB 675 1Hz with 33 1 3 rpm 1170 1Hz with 78 rpm Static Balanced S shaped with detachable headshell 234mm 20mm 0 4g 0 7g 6 10g AC110 127V 220 240V 50 60Hz 15 Watts 450 x 352 x 148 5 mm 17 3 4 x 13 3 4 x 5 7 8 10 8Kgs 24 lbs Specifications and design may be changed without notice due to continual product improvement Numark The Leader in DJ Technology 1999 Numark Industries 11 htto www numark com Numark LIMITED PRODUCT WARRANTY 1L What is covered and for how long NUMARK INDUSTRIES LCC NUMARK warrants to the original purchaser that NUMARK S DJ mixers and amplifiers are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the following period of time after that date for 2 Years The warranty is extended to 3 Years with the completion of the warranty card provided that the warranty card is completed and returned within 30 days from the date of purchase All other NUMARK products are warranted for 1 Year including but not limited to CD players turntables preamplifiers beatkeepers equalizers microphones headphones and all other accesories 2 What is not covered T
7. beam of light at the Strobe Dots 5 By doing so the large dots will seem not to move in Quartz Lock mode 5 Strobe Dots Four rows of dots that indicate various stages in pitch adjust 3 3 outer row 0 large dots 3 3 next row 6 inner row 6 Platter Place this on the Center Spindle 7 and carefully position with the Alignment Pins 17 7 Center Spindle Keeps platter and records centered Place the supplied slipmat on the Center Spindle now Numark The Leader in DJ Technology 1999 Numark Industries 6 htto www numark com 8 45 Adapter Place on Center Spindle 7 for playing 7 records with large center holes 9 Forward Reverse Buttons These determine the direction the platter will spin 10 Lid Hinge Holder Place the bottom tabs of your lid hinges in here after you finish assembly 11 Extra Stylus Holder Place extra headshells here 12 Tone Arm Assemble Explained in tonearm section 13 Pitch Adjust use this the change the speed of the platter when quartz lock is inactive You can adjust the revolutions by 10 PRO TT 1 14 Quartz Lock On will hold the revolution speed at exactly the specified speed 3 Off will allow use of the Pitch Adjust 13 15 LCD Display Explained in Display Section 16 Target Light Press the button to the right and a light will pop up directed at the stylus position 17 Voltage Selector with unit unplugged set the desired voltage
8. for your location using a screw driver lt TONE ARM ASSEMBLY 20 Headshell Attach the cartridge here When installing a cartridge refer to the installation instructions supplied by the manufacturer of that cartridge During installation attach the stylus protector to guard the stylus tip from damage Attach wires as follows White L Left channel Blue L Left channel Red R Right channel Green R Right channel 21 Headshell Locking Nut Attach headshell by inserting into the front end of the tonearm then turn the locking nut clockwise with the head shell firmly held horizontally 22 S Shaped Tone Arm 23 Tone Arm Clamp and Rest Use this rest the tone arm and clamp it in position during transportation 24 Tone Arm Lift This elevates the tone arm above the record surface 25 Tone Arm Lift Adjust Screw Controls the amount of lift 26 Tone Arm Lever Controls the up and down action of the Tone Arm Lift Numark The Leader in DJ Technology 1999 Numark Industries 7 htto www numark com PRO TT 1 27 Anti Skate Control This applies inward force to the 3 Release the arm clamp and lift the tonearm from the tonearm so it doesn t skip outward across the record due to arm rest so it moves freely the centrifugal force of the record spinning Cartridge manufacturers usually specify the proper setting of this 4 Rotate the counterweight until the tonearm is
9. h the address or phone numbers below 2 A copy of the original sales receipt must also be included for the equipment to be repaired under warranty 3 The faulty equipment must be packed in its original packaging 4 One additional outer layer of packaging must be included to ensure product safety Failure to do so may inadequately protect the equipment in transit and therefore jeopardize the customer s warranty 5 Numark will not accept COD shipments and no call tags will be issued for merchandise return 6 Numark will not return repaired merchandise to customers by priority service unless by written request at the customer s cost Requests must be submited in writing with merchandise returned 7 The defective Numark equipment should be sent FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and original sales receipt enclosed to Numark NDUSTRIES Attention Service Department Phone 1 401 295 9000 11 Helmsman Avenue Fax 1 401 295 5200 North Kingstown RI 02852 USA E mail numark numark com
10. his Limited Warranty is conditioned upon proper use of the product by the purchaser This Limited Warranty does not cover a defects or damage resulting from accident misuse abuse neglect unusual physical or electrical stress modification of any part of the product or cosmetic damage b equipment that has the serial number removed or made illegible c all plastic surfaces and other externally exposed parts that are scratched or damaged due to normal use d defects or damage from improper testing operation maintenance installation adjustment or service of the mixers e crossfaders 3 What are NUMARK S obligations During the applicable warranty period NUMARK will repair or replace at NUMARK S sole discretion without charge to the purchaser any defective component part of the mixer To obtain service under this Limited Warranty purchaser must first contact NUMARK and obtain a return authorization number RA Purchaser must then return the mixer to NUMARK in an adequate container for shipping accompanied by purchaser s sales receipt or comparable proof of sale showing the date of purchase the serial number of the product and the seller s name and address To obtain an RA and assistance on where to return the mixer contact NUMARK customer service at 401 295 9000 Upon receipt NUMARK will repair or replace the defective products NUMARK may at NUMARK S sole discretion use rebuilt reconditioned or new parts or components when
11. ifies otherwise LCD DISPLAY 31 Speed Indication 33 33rpm 45 45rpm 33 45 78 rpm 32 Speed Adjust Indication This will display up to 10 adjustment in speed 33 Play Pause Indicates current state of the platter 34 Pitch Quartz indicates current mode of operation 35 Platter Wheel simulates all actions of speed and direction of the platter Numark The Leader in DJ Technology 1999 Numark Industries 8 http www numark com REAR PANEL DIAGRAM PRO TT 1 40 Removable Lid Protects the turntable from dirt and dust 41 Hinge Assembly Holds the lid and turntable together Attach now by sliding the bottom tabs of the Hinge Assembly into the Hinge Holders 10 42 Platter Speed Output This output is to be used with external devices the require platter speed information 43 Remote Start Stop This is used with external control devices Tech note This circuit is a normally open use a momentary switch and a 1 4 mono plug to change play states of the unit 44 Adjustable Feet Turn feet to level the platter surface 45 Phono Output Plug these into your mixer or preamplifiers turntable input 46 Ground Cable Attach to the ground screw on your mixer or preamplifier to prevent turntable hum 47 Power Cord Plug this into an appropriate power outlet after checking your power setting switch 18 under the platter Note Please refer to CAUTION on page 2 concern prope
12. in Unit 2 Turntable platter 3 Rubber mat 14 Slip mat 5 Dust cover 6 45 rpm adaptor 17 Counterweight 8 Headshell 8 Operating instructions 9 Registration Card Numark The Leader in DJ Technology 1999 Numark industries 3 htto www numark com PRO TT 1 IMPORTANT INFORMATION Please read this entire manual before connecting the PRO TT 1 to your system For optimum performance Always make sure that AC power is OFF while making any connections Do not force the platter to stop moving while the motor is engaged Quality ipmats should be used to hold records in position Forcing the motor to stop can camage the motor assembly Never use spray cleaners or oils on the slide control Residues cause excessive dirt build up void your warranty In normal use Is can last for many years If they ely because of a dirty or dusty malfunction environment Never attempt to make any adjustments or repairs other than those described in this manual Take the PRO TT 1 to your dealer or to an authorized Numark Service Center Do not place the unit in a location where it will be exposed to direct sun light or near a heating appliance Do not place the unit in a location where there is high humidity or a lot of dust Cartridge may pick up slight sound pressure or vibrations of the speakers coming along the floor or through the air resulting in howling Find a location which is very
13. latter is in normal turntable speed Move the pitch control slider up or down to adjust the speed 11 To suspend play lift tone arm with cueing lever 12 When play is finished raise the cueing lever move the tonearm to the arm rest secure the tonearm with the arm clamp 13 Turn off the target light off by pushing the light back down 14 Press the Start Stop button to stop the platter rotating turn the power dial to turn off the power Maintenance Routine maintenance should be performed by cleaning the stylus periodically with a soft brush to prevent the accumulation of dust When the sound becomes distorted or noisy check the stylus If it is worn out replace with a new one From time to time the dust cover and turntable cabinet should be wiped with a soft dry cloth Use of any volatile materials as alcohol thinner benzine etc may remove the paint or damage the luster and should not be used Numark The Leader in DJ Technology 1999 Numark industries 10 htto www numark com SPECIFICATIONS TURNTABLE SECTION Type Driving method Motor Turntable platter Turntable speed Pitch Variance Starting Torque Braking OUTPUT Wow and flutter SIN ratio Output Difference Output Level Channel Separation Pitch TONEARM SECTION Type Effective length Overhang Tracking Force Anti Skate Cartridge Weight GENERAL Power supply Power consumption Dimension W x D x H Weight PRO TT 1 3 speed full manu
14. ld damage speakers due to amplifier clipping Avoid amplifier clipping at all costs this occurs when the red LEDs usually on the front panel of most professional power amplifiers start flashing Clipping is when the power amplifier is distorting and working beyond it s limits Amplifier distortion is THE major cause of speaker failure To prevent fire or shock hazard do not expose the unit to rain or moisture Never place cans of beer soda glasses of water or anything wet on top of the turntable Numark The Leader in DJ Technology 1999 Numark industries 4 htto www numark com PRO TT 1 CONGRATULATIONS You are now the owner a Numark PRO TT 1 Professional Turntable the ultimate tool for todays skilled turntablist This unit has been designed by DJs for DJs With it s super high torque platter and large back lit display the Numark PRO TT 1 gives the professional absolute total control Enjoy this turntable and remember BE CREATIVE Thank you for buying Numark DJ products FEATURES e 10 pitch adjustment High Torque Platter M otor Start Stop Button High Torque Braking e 33 45 78 RPM speeds e Forward and Reverse Platter Direction Unique Top Plate LCD Display indicating e Play Pause M ode e Pitch Change Percentage e Platter Speed Quartz Lock M ode e Rotating 12 segment circular display indicating the spinning actions of the platter at all times S Shaped Tone arm assembly wi
15. nstructions The safety and operating instructions should be kept for future reference 3 Heed Warnings All warnings on this product and in these operating instructions should be followed 4 Follow Instructions All operating and other instructions should be followed 5 Water and Moisture This product should be kept away from direct contact with liquids 6 Heat Avoid placing this product too close to any high heat sources such as radiators 7 Power Sources This product should be connected to a power supply only of the type described in these operating instructions or as marked on the unit 8 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord 9 Object and Liquid Entry Take care that objects do not fall into and that liquids are not spilled into the inside of the turntable 10 Damage Requiring Service This product should be serviced only by qualified personnel If you have any questions about service please contact Numark at the number s shown on the back cover of this manual 11 Grounding or Polarization Precautions should be taken so that the grounding or polarization means built into the turntable is not defeated 12 Internal External Voltage Selectors Internal or
16. r use of power Your assembly should now be complete Place your turntable on a vibration free level surface and attach to your mixer or preamplifier If you are using the turntable for slip cueing or mixing music you will want to use the slipmat and not the rubber mat Numark The Leader in DJ Technology 1999 Numark Industries 9 htto www numark com PRO TT 1 GENERAL OPERATING INSTRUCTIONS 1 Turn the power dial to turn on the speed indicator and the strobe illuminator will light up N Turn on and raise the target light for illuminating the stylus tip by pushing the target light button w Place a record on the turntable mat when playing a 45rpm record with a large center hole place the 45 rpm adaptor on the center spindle Set the rotation speed 33 45 78 to match the record Release the arm clamp Set the cueing lever to the up position Press the Start Stop button the turntable platter will start to rotate Move the tonearm over the desired groove ooN A Set the cueing lever to the down position the tonearm will descend slowly onto the record and play begins 10 Adjust the pitch to a desirable speed The pitch control is variable in a range of 10 During play observe the strobe dots if the strobe dots appear to the right the pitch is slower than the rated speed if flow to the left the pitch is faster than the rated speed if the strobe dots appear stationary which means the p
17. stable and free of vibration The legs have functions for adjusting the height of the unit itself Adjust the legs to stabilize the main body horizontally A NOTE ON CABLES Quality cable makes a big difference in lI audio fidelity and punch See your I Numark dealer or an electronics or audio specialist store if you are not sure which cables to get GENERAL SYSTEM PRECAUTIONS Use appropriate cables throughout your system Quality shielded audio cables and terminated shielded video cables low capacitance preferred Speaker cables must be 14 gauge minimum 12 or 10 gauge is etter Be sure plugs and jacks are tightly mated Loose connections can cause hum noise or intermittents that could easily damage your speakers Reliability will be enhanced through the use of banana connectors on the speaker wires Observe correct speaker wire polarity If in doubt consult your Numark dealer or a qualified technician Take care to connect only one cable at a time Pay attention to the color coded labelled Input and Output jacks ALWAYS remember TURN AMPS ON LAST AND OFF FIRST Begin with master faders or volume controls on minimum and the amplifier gaininput control s down Wait 8 to 10 seconds efore turning up the volume This prevents transients which may cause severe speaker damage Use restraint when operating controls Try to move them slowly Rapid adjustments cou
18. th Counterweight e Height Adjustment e Skating Adjustment e Height Lock e Lever lift with height adjustment Tone arm holder with locking mechanism Pop up Stylus Target Light Quartz Lock of 0 speed position 45RPM adapter and holder Extra Stylus H older Output for e Audio Left Right amp Ground e Platter Speed to be used with external process devices External START STOP control Adjustable Feet for Leveling Easily removable smoked plastic lid Numark The Leader in DJ Technology 1999 Numark industries 5 htto www numark com PRO TT 1 FEATURES OPERATING amp ASSEMBLY INSTRUCTIONS To fully appreciate the features of theINumuaurk PRO TT 1 please read this entire manual before you begin operation The PRO TT 1 should be placed on a level sturdy surface Keep in mind that there are a few features you may never have seen before on a turntable of this type that you will need to read about to use properly Start by removing all parts from the package and place on a level surface Carefully check all packing material for hidden parts Use the contents guide for reference Do not discard any packing materials 1 Power Dial On Rotate Right Off Rotate Left 2 START STOP Pressing once engages high torque motor pressing again engages brake 3 Platter Revolution Speed Buttons 33rpm Press 33 45rpm Press 45 78rpm Press 33 and 45 4 Strobe Light This Pulses a
Download Pdf Manuals
Related Search