Numark Industries DM1295 Musical Instrument User Manual
Contents
1. S product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty The agents employees distributors and dealers of NUMARK are not authorized to make modifications to this Limited Warranty or make additional warranties binding on NUMARK Accordingly additional statements such as dealer advertising or presentation whether oral or written do not constitute warranties by NUMARK and should not be relied upon How does state law apply to this warranty SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER This Limited Warranty gives you specific legal rights You may also have other rights which vary from one jurisdiction to another RETURN INFORMATION A Return Authorization number must be obtained from Numark through the address or phone numbers below A copy of the original sales receipt must also be included for the equipment to be repaired under warranty The faulty equipment must be packed in its original packaging One additional outer layer of packaging must be included to ensure product safety Failure to do so may inadequately protect the equipment in transit and therefore jeopardize the customer s warranty e Numark will not accept COD shipments and no call tags will be issued for merchandise return f Numark will not return repaired me2. hear is the cue source When the knob is all the way to the used to tailor the sound to the acoustical requirements of right you will hear what is playing through the master output the room Center frequencies are 42Hz 152Hz 480Hz By blending beats can be matched exactly and segues can be 1 5kHz 4 8kHz and 15 4kHz Faders have a center detent smooth when a song is cued for an accurate flat response Below is a typical house 19 Headphone Level adjusts cue volume EQ curve Notice how the knobs above 0 balance out 20 Headphone Jack to plug in your 14 headphones the knobs below Start with this setting 1f you ve never used a graphic EQ before 21 Power Switch turns unit on and off 22 BNC Connector for a 12V gooseneck light to be attached Below is an example of a poor EQ curve because it cuts the output volume down by 6 10dB You have to compensate by running the Master output higher Below is the worst sort of curve to use because you are using EQ to add volume With exaggerated boost you can easily run your power amplifiers into clipping see page 6 and damage your speakers GENERAL EQ HINTS e Boost the 42Hz band for deep bass tones and solid kick drum sound Use sparingly because this dramatically increases demand on power amplifiers and could drive them into clipping e Cut slightly at 152Hz and more at 460Hz for extra clarity Note Cutting is preferable to boosting e Boost
3. into AC power Now you are ready to switch everything on IMPORTANT Alwavs switch on your audio input sources such as turntables or CD players first then your mixer and finally any amplifiers When turning off always reverse this operation by turning off amplifiers then your mixer and then input devices Main Main Balanced Sound System Microphone 2 w Amplifier Keyboard Tape Deck Digital Sampler Turntable 1 AC Outlet Zone Tape Deck Sound System CD Player w Amplifier Turntable 2 Turntable 3 ex Main Unbalanced Sound System w Amplifier Numark The Leader in DJ Technology 2000 Numark Industries 9 http www numark com DM1295 SPECIFICATIONS INPUTS Line 10Kohm input impedance 110mV rms sensitivity for 1 22V output Mic 10Kohm input impedance unbalanced 1 6 mV rms sensitivity for 1 22V output 500mV rms max input Talkover attenuation variable from no cut to 16 dB Phono 47Kohm input impedance 1 8mV rms sensitivity 1 KHz for 1 22V output OUTPUTS Line 9V rms max Headphone Amp 1V rms watt into 16ohm Distortion less than 0 01 SIGNAL TO NOISE RATIOS vs maximum output Line Better than 96 dB Mic Better than 78 dB Phono Better than 87 dB JIS weighted FREQUENCY RESPONSE Line 20 Hz 22k Hz 0 5 dB Line 20 Hz 20k Hz 0 5 dB Phono 1 dB except for controlled attenuation of 3 dB 20 Hz to reduce rumble and feedback EQUALIZER 6 Band Stereo Gr
4. 15kHz for a little sizzle e Asa general rule less equalization is better 17 Equalizer On Off This controls whether your final output will be routed through the EQ or not Numark The Leader in DJ Technology 2000 Numark Industries 5 http www numark com DM1295 Numark The Leader in DJ Technology 2000 Numark Industries 6 http www numark com DM1295 SAMPLER OPERATION ne This sampler was designed for ease of use and understanding It can retain in memory up to 110 seconds worth of sampling Each bank can save 27 5 seconds for playback even after the unit is shut down It s as simple as 1 pressing a channel send 2 recording the sample 3 playing it back Enjoy a whole new way to sample Output Gain Control adjusts the volume of the sampler Pitch Adjust changes the playback pitch of the sample Moving left slows down the playback moving right speeds it up Record Play mode select sets the operation of the sampler Stutter is used to allow samples to play fully through until retriggering Cue is used for monitoring the sampler SY cp CODES ie Sampler Banks for storing 4 samples up to 27 5 seconds in length RECORDING SAMPLES 1 Determine your audio source and press the send button of the channel you wish to sample 2 Setthe mode select to record by depressing the button once 3 Move toggle in either direction to record the sample then move it back to the center to end the sam
5. Cue Assign are used to route Pre Fader Level PFL and on Mic 2 is controlled only through the Mic 2 Fader channel audio to the Headphone Section The channel faders do Talkover turns down the input level of your music not control the Cue volume sources from Channels 1 4 Talkover is very useful for Effect Send Channels 1 4 Depress these buttons when you making announcements without adjusting any levels want the signal from any input channel to be routed to the Try using this feature for audience participation when sampler on the Send Out Jacks you want the music to temporarily cease and the audience to be heard YEAH CROSSFADER Crossfader Assign Knob determines which input channel will OUTPUTS be heard when the crossfader is moved towards the knob With 12 Master Fader controls the overall output level the crossfader centered both assigned channels are live Use the crossfader for fast and seamless segues from one selected 13 Stereo Mono toggle adjusts the Master output for stereo or channel to the other mono operation Replaceable Crossfader achieves clean segues between the 14 Booth Zone Fader controls speaker volume for a remote zone two input channels selected by the Crossfader Assign or booth monitors NOTE This can also be used to supply line level audio to a lighting controller or to lights that are sound Note The crossfader is a user replaceable item and subject to an uad wear Excessive force can wear out
6. K S liabilities THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY TOGETHER WITH ANY IMPLIED WARRANTIES COVERING NUMARK MIXERS INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW NUMARK SHALL NOT BE LIABLE FOR ANY SPECIAL INCIDENTAL CONSEQUENTIAL INDIRECT OR SIMILAR DAMAGES LOSS OF PROFITS DAMAGES TO PURCHASER S PROPERTY OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE MISUSE OR INABILITY TO USE ANY NUMARK MIXER BREACH OF WARRANTY OR NEGLIGENCE INCLUDING BUT NOT LIMITED TO NUMARK S OWN NEGLIGENCE EVEN IF NUMARK OR ITS AGENT HAS BEEN ADVISED OF SUCH DAMAGES OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK S MIXERS AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER S EXCLUSIVE REMEDY IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS This Limited Warranty allocates risk of product failure between purchaser and NUMARK and NUMARK
7. Numark Professional Disc Jockey Products DM1295 Owner s Manual 2000 Numark Industries http www numark com DM1295 Safety Information AN CAUTION RISK OF ELECTRIC SHOCK AN DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanvina this appliance CAUTION FOR USA amp CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE SAFETY INSTRUCTIONS a b c d e g Read Instructions All the safety and operating instructions should be read before this product is connected and used Retain Instructions The safety and operating instructions should be kept for future reference Heed Warnings All warnings on this product and in these operating instructions should be
8. ance installation adjustment or service of the mixers e crossfaders What are NUMARK S obligations During the applicable warranty period NUMARK will repair or replace at NUMARK S sole discretion without charge to the purchaser any defective component part of the mixer To obtain service under this Limited Warranty purchaser must first contact NUMARK and obtain a return authorization number RA Purchaser must then return the mixer to NUMARK in an adequate container for shipping accompanied by purchaser s sales receipt or comparable proof of sale showing the date of purchase the serial number of the product and the seller s name and address To obtain an RA and assistance on where to return the mixer contact NUMARK customer service at 401 295 9000 Upon receipt NUMARK will repair or replace the defective products NUMARK may at NUMARK S sole discretion use rebuilt reconditioned or new parts or components when repairing any product or replace a product with a rebuilt reconditioned or new product Repaired mixers will be warranted for a period equal to the remainder of the original Limited Warranty on the original mixer or for 90 days whichever is longer All replaced parts components boards and equipment become the property of NUMARK If NUMARK determines that any mixer is not covered by this Limited Warranty purchaser must pay all parts shipping and labor charges for the repair or return of such mixer What are the limits on NUMAR
9. aphic EQ Band centers 42 Hz 152 Hz 480Hz 1 52KHz 4 8KHz 15 36KHz 15 dB SAMPLER Sampling length 110 Seconds 27 5 seconds per bank POWER CONSUMPTION 20 Watt typical 28 watt with full headphone output DIMENSIONS 482mmx232mmx 111mm 19 x9 1 8 x4 3 8 WEIGHT 5 1kgs 11 21bs Numark The Leader in DJ Technology 2000 Numark Industries 10 http www numark com DM1295 BLOCK DIAGRAM O j dWY S3NOHd o E 3 o INdINO S3NOHd M 23431 3n AYIdSIG 333 1 ze 1NO JSON WSs 430 N0 N3MOd dWy H1008 Aer gt igs lt PS 43431 H1008 indino H1008 x K x 13431 Q u31SUM 1ndino A LU H31SUH SS lt poss dut N31SUH inano y WAS 938 X 1InoNIO S NITJHYS N5ISSU 3304455059 pu 63 Jana dW NIMU5 I A p Q 73437 S LL 2 4 gt p gt IONLNOD 3NO1 SL E S 373s ONITdWYS 330 H07 3 81 S3N13 A ot gt gt 713437 H9 lt EI Te AM KC gt Jang n A CM e CT ES rn Ce 1439 3n5 193135 1ndNI 93NIA tHo a NA Dr 73437 i T H32110ene3 EH A MM pe 2 VAN amm A2N3n 384 aang 03 vyra d ee b 1e rae z oO ty Es d D lt e 1431 3n9 193135 10dNI Qs 3NI1 0NOHd THO as 73437 zH lt lt k d 2 AV lt L 3ang 3 VII l
10. followed Follow Instructions All operating and other instructions should be followed Water and Moisture This product should be ee kept away from direct ERAT contact with liquids Heat Avoid placing this product to close to any high heat sources such as radiators Ventilation The appliance should be situated so that it s location or position does not interfere with it s proper ventilation For example the appliance should not be situated on a bed sofa rug or similar surface that may block the ventilation opening WA or placed in a built y installation such as bookcase or cabinet that may impede the flow of air through the ventilation openings h i j n 0 Power Sources This product should be connected to a power supply only of the type described in these operating instructions or as marked on the unit Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them When removing the cord from a power outlet be sure to remove it by holding the geo d plug attachment f ag and not by pulling on the cord S CN Object and Liquid Entry Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer Cleaning The appliance should be cleaned only as recommended by the manufacturer Non use Periods The power cord of the appliance
11. ple The unit will return to play mode Using the up position allows you to sample without holding the toggle PLAYING SAMPLES 1 Move toggle in the down direction to play only once If the unit is in stutter mode the sample will play to the end unless the toggle is moved again If the unit is not in stutter mode then playback will end when the toggle is released 2 Move the toggle upward to play a sample as a loop Moving multiple samples up will allow them to play in sequence 3 While a sample is playing as a loop other samples can be played back as well as single play One single play sample and one loop can be played at the same time creating some very interesting effects Numark The Leader in DJ Technology 2000 Numark Industries 7 http www numark com DM1295 REAR PANEL FEATURES Power Connector Plug in power cord here and check the voltage level to match your country s standard GND is the grounding lug for turntables 1 2 and 3 phono inputs on Channels 1 2 and 3 Always use this connection your turntable cable should have a grounding wire The Stereo Main Outputs are low impedance RCA connectors controlled by the Master fader The Stereo Zone Outputs are low impedance unbalanced RCA jacks controlled by the Zone Level control The Tape Outputs are low impedance unbalanced RCA jacks which output the program mix and allow you to connect any recording device The Send can be attached to an external effects proce
12. po 2 Ce 1437 M E Z3NIT Z NOHd e S fh 193135 1ndNI gt ZHO In 25 xc AIT ESS rbd Inm 193135 1 dNI NS 3ang THD gt p z NN lt A SAS SM o Tano Numark The Leader in DJ Technology http www numark com 23 d 2000 Numark Industries Numark Professional Disc Jockey Products LIMITED PRODUCT WARRANTY What is covered and for how long 1 NUMARK INDUSTRIES LCC NUMARK warrants to the original purchaser that NUMARK products including but not limited to DJ mixers amplifiers CD players CD Mix Stations turntables preamplifiers beatkeepers equalizers microphones headphones cartridges and all other accessories are to be free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer for a period of 1 Year What is not covered This Limited Warranty is conditioned upon proper use of the product by the purchaser 2 This Limited Warranty does not cover a defects or damage resulting from accident misuse abuse neglect unusual physical or electrical stress modification of any part of the product or cosmetic damage b equipment that has the serial number removed or made illegible c all plastic surfaces and other externally exposed parts that are scratched or damaged due to normal use d defects or damage from improper testing operation mainten
13. rchandise to customers by priority service unless by written request at the customer s cost Requests must be submitted in writing with merchandise returned g The defective Numark equipment should be sent FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and original sales receipt enclosed to o ce Numark INDUSTRIES Attention Service Department Phone 1 401 295 9000 11 Helmsman Avenue Fax 1 401 295 5200 North Kingstown RI 02852 USA Web www numark com
14. sampler CONGRATULATIONS You have purchased the DM1295 stereo preamp mixer with onboard sampler Numark s engineers have designed this mixer to accommodate both the mobile DJ market and the professional installation market The DM1295 provides the end user with high end audio circuitry combined with maximum versatility to meet the demands of every intended situation This mixer features 8 line 3 phono and 2 microphone inputs balanced XLR outputs and a built in sampler with 110 seconds of memory storage and polyphonic playback Thank you for purchasing NUMARK products Mixer Features SAMPLER Features 8 Line 3 phono 2 mic inputs 110 seconds of memory storage Completely assignable and replaceable cross fader Retainable memory Dual 6 band graphic equalizer with on off switch Polyphonic playback Master and zone level controls Pitch adjustment of 35 to 100 Mic inputs have EQ and talk over control Looping and single play capability with stuttering Front panel mic with Neutrik connectors XLR or 1 4 Booth output Individual channel sends Split cue headphone monitoring Master balanced XLR outputs 12V BNC light connector Table of Contents Safety Measures 2 Introduction 3 Specifications 10 Registration 3 Bock Diagram 11 Description of the Features 4 Warranty 12 Quick Setup Diagram 7 Product Registration Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom
15. should be unplugged from the outlet when left unused for long periods of time Damage Requiring Service Never attempt to make any adjustments or repairs other than those described in this manual Only qualified personnel should service this product If you have any questions about service please contact Numark at the number s shown on the back cover of this manual Grounding or Polarization Precautions should be taken so that the grounding or polarization means built into the CD player is not defeated Internal External Voltage Selectors Internal or external voltage selector switches 1f any should only be reset and re equipped with a proper plug for alternative voltage by a qualified service technician Do not attempt to alter this yourself WARNING To reduce the risk of fire or electrical shock do not expose this appliance to rain or moisture Electrical equipment should NEVER be kept or stored in damp environments SERVICE INSTRUCTIONS Disconnect power cord before servicing Replace critical components only with factory parts or recommended equivalents For AC line powered units Before returning repaired unit to user use an ohmmeter to measure from both AC plug blades to all exposed metallic parts The resistance should be no more than 100 000ohms Numark The Leader in DJ Technology 2000 Numark Industries http www numark com DM1295 Numark 781295 prortssionat ns mmer with onboard
16. ssor such as a sampler Line Inputs 1 5 are unbalanced RCA jacks The Line Input is selected with the toggle switch on the front panel You can connect stereo audio from HiFi VCRs cassette and reel to reel tape decks DAT machines CD players laser discs tuners even synthesizers or other mixing consoles NOTE Plug mono audio sources into both Left and Right inputs using a Y cable connector 10 11 Line Phono Input switch Use this to allow line level equipment to be plugged into your phono inputs giving you a total of 8 line input options Phono Inputs on Channels 1 2 and 3 use unbalanced RCA jacks Your input signal is fed directly to the DM1200 s high quality RIAA phono pre amplifiers so use this position only for moving magnet cartridges Line level sources will overload the sensitive phono pre amps and will sound very bad so always be sure to toggle the line phono switch over to line before connection of line sources The Balanced Main Outputs are low impedance XLR type connectors controlled by the Master fader Mic 2 is the mic input for Channel 4 Numark The Leader in DJ Technology 2000 Numark Industries 8 http www numark com DM1295 QUICK SETUP DIAGRAM VERY IMPORTANT Please read this entire manual before connecting this unit to your system For optimum performance Always make sure that AC power is OFF while making any connections 9 Use appropriate cables throughout your system Do no
17. t use excessively long cables i e over 50ft 14m Be sure plugs and jacks are tightly mated Loose connections can cause hum noise or intermittence that could easily damage your speakers Make the input and output connections with readily available low capacitance stereo cables Quality cable makes a big difference in audio fidelity and punch See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get ALWAYS remember TURN AMPS ON LAST AND OFF FIRST Begin with master faders or volume controls on minimum and the amplifier gain input control s down Wait 8 to 10 seconds before turning up the volume This prevents transients which may cause severe speaker damage 9 Use restraint when operating controls Try to move them slowly Rapid adjustments could damage speakers due to amplifier clipping Avoid amplifier clipping at all costs this occurs when the red LEDs usually on the front panel of most professional power amplifiers start flashing Clipping is when the power amplifier is distorting and working beyond it s limits Amplifier distortion is THE major cause of speaker failure Study this setup diagram Make sure all faders are at zero and all devices are off First connect all input sources and processors Next connect your microphone and monitor headphones Finally connect the stereo outputs to the power amplifier s and or audio receivers such as tape decks Plug your mixer
18. the fader quickly This is not a warranted item In case of failure Simply unscrew the two 15 Stereo Auto Peak Hold Level Indicator quickly and large screws that hold it in place lift it out and disconnect its cable Re attach the new crossfader and screw the mounting plate back onto the unit you re back in business MICROPHONE Neutrik Combo connector allows connection of either a 1 4 jack or an XLR jack This is ideal for connecting an XLR gooseneck directly into the mixer accurately tracks level of audio output The red LEDs for 3dB 5dB and 8dB hold program peaks for a second or two With peak metering it s OK to be in the red as long as 5dB or 8dB aren t constantly lit When using as a master output meter set the crossover equalizer and power amp inputs to avoid distortion at each step in the audio chain Proper attention to the peak meter results in the punchiest possible sound without audible distortion Numark The Leader in DJ Technology 2000 Numark Industries 4 http www numark com DM1295 EQUALIZER SECTION HEADPHONE CUEING 16 6 Band Stereo Graphic Equalizer EQ EQ 18 Headphone Mix controls the mix of cue and program the final mix of music played through the master output signals to compensates for differences in source material sound t your headphones When the knob is moved to the left all you quality In ultra compact mobile systems this EQ can be will
19. you purchased the unit Retain this information and your original purchase receipt for your records Please return the enclosed warranty card to register your unit with us MODEL PURCHASED FROM SERIAL NUMBER DATE OF PURCHASE Numark The Leader in DJ Technology 2000 Numark Industries 3 http www numark com DM1295 MIXER FEATURES S 16 2 lo 600600997008000 LL LL 15 17 1 13 e a Em En ps e z d E P o EE cE onm o 3 6 9 e IF eeee 4 19 20 INPUTS Input Toggle Switches select which source will be live to that 8 Treble and Bass Controls for fine tuning the tone of your channel based on what you have connected to the rear panel voice through the sound system The controls are detented for input section setting tone flat Input faders control individual source levels in the mix 9 DJ Mic Gain Control for volume adjustment of the Note Never use spray cleaners on the slide controls Residues Neutrik Combo connector on the faceplate cause excessive dirt build up and this will void your warranty 10 Mic 2 Gain Control for volume adjustment of the 4 In normal use slide controls can last for many years If they RU rea pael malfunction usually because of a dirty or dusty environment PRESSE PAPERS consult a professional technician 11 Mic Off On Talkover Switch Off On turns Mic loff Channel
Download Pdf Manuals
Related Search