Numark Industries DM1001X Music Mixer User Manual
Contents
1. input Phono 47Kohm input impedance 1V rms sensitivity 1 2 for 1 22V output Outputs Line 7V rms max Headphone 5 watt into 47 Distortion less than 0 01 Signal to Noise Ratio vs maximum output Line Better than 89dB Mic Better than 72dB Phono Better than 80dB Frequency Response Mic 20Hz 15 KHz 0 5dB Line 20Hz 20 KHz 0 5dB Phono 1dB except for controlled attenuation of 3dB 20Hz to reduce rumble and feedback Channel EQ Bass 15 30 dB 40 Hz Middle 15 30 dB 1 36 kHz Treble 12 25 dB 20 kHz Talkover Attenuation 16dB Channel KILL DM1002X only Bass 66 dB 50 Hz Middle 31 dB 1 2 kHz Treble 66 dB 15 kHz Power Consumption 5 watt typical 7 8watt with full headphone output Numark The Proven Leader in Technology 1998 Numark Industries 10 http www numark com DM1001X DM1002X BLOCK DIAGRAM Numark The Proven Leader in Technology 1998 Numark Industries 11 http www numark com Numark Professional Disc Jockey Products Warranty and Service Information Numark Industries LLC and Numark International Inc hereafter Numark warrants each new product manufactured and or supplied by it to be free from defects in material or workmanship under conditions of normal use and service for 1 year beginning on the date of purchase from an authorized Numark Dealer but not to exceed 2 years from date of shipment by Numark The Numar2. other Note The crossfader is user replaceable in case of failure Simply unscrew the two large screws which hold it in place lift it out and disconnect it s cable Re attach the new crossfader and screw the mounting plate back onto the unit you re back in business 9 The Crossfader Control toggle allows the DJ to reverse the direction of the crossfader or turn it off By reversing direction Channel 2 will be on the left and Channel 1 will be on the right 10 Transform Buttons are for quickly reversing the crossfader direction in order to create various special effects Numark The Proven Leader in Technology 1998 Numark Industries 6 http www numark com CUE SECTION 11 Cue Assign Toggle is used to route pre fader channel audio to the Cue Monitor Section 12 The Program Mix controls the mix of Cue and Program audio in the headphones so that beats can be matched exactly and segues are smooth when a song is cued 13 The Headphone Volume control sets the level for you headphones 14 The Headphone Jack is used to connect headphones with a standard 1 4 stereo plug DM1001X DM1002X 15 The Stereo Master Fader controls the overall output level 16 Stereo Output Level Indicator This fast accurate stereo meter tracks the output level It s OK to be occasionally in the red as long as 5dB or 8dB aren t constantly lit Set the crossover equalizer and power amp inputs to avoid distortion
3. FEATURES Crossfader Reverse switch Crossfader Curve Adjust Switch 4 Phono Inputs with low noise RIAA preamps 2 Line Inputs DJ Mic Input 35DB KILL switches for Bass Middle amp Treble on each channel Bass Middle amp Treble controls on each channel with 30dB Cut ability on each control for special effects and creative mixing Individual Gain Controls on each channel User replaceable crossfader e Transform buttons Cueing for each channel 9 5 24 wide Rugged construction Numark The Proven Leader in DJ Technology 1998 Numark Industries 4 http www numark com IMPORTANT INFORMATION Please read this entire manual before connecting the mixer to your system For optimum performance Always make sure that AC power is OFF while making any connections Do not use excessively long cables i e over 50ft 14m Be sure plugs and jacks are tightly mated Loose connections can cause hum noise or intermittents that could easily damage your speakers Never use spray cleaners on the slide controls Residues cause excessive dirt build up and this will void your warranty In normal use slide controls can last for many years If they malfunction usually because of a dirty or dusty environment consult a professional technician Never attempt to make any adjustments or repairs other than those described in this manual Take the unit to your dealer or to an autho
4. Numark Professional Disc Jockey Products DM1001X DM1002X STEREO MIXER with Crossfader Curve Switch OWNER S MANUAL 58 E Q I Q I cave 48 FRE mae aes s 6 amp 4 e gt ww a w TREBLE la a y CUE MIX TREBLE CUE MIX 5 gt P i 2 A 3 le 25 A ESME a le ee 1 HEADPHONE 6 6 jo 4 i je je je gt le 5 e MasteR MASTER ans TREBLE MIDDLE BASS TRANSFORM pastor ff SEA TRANSFORM NUMARK INDUSTRIES 11 Helmsman Road North Kingstown 02852 http www numark com DM1001X DM1002X Safety Information and Product Registration CAUTION N RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION REDUCE THE RISK OF ELECTRIC SHOCK DO REMOVE ANY COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY The lightning flash
5. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EQUIPMENT TRANSPORT A Return Authorization number should be obtained from Numark through the addresses or phone numbers below It is the customer s obligation when returning faulty equipment to properly pack the Numark equipment in its original packaging Failure to do so may inadequately protect the equipment in transit and therefore jeopardize the customer s warranty The defective Numark equipment should be sent FREIGHT PREPAID with Return Authorization number to NUMARK INDUSTRIES 11 Helmsman Road Telephone 1 401 295 9000 North Kingstown RI 02852 U S A Fax 1 401 295 5200 Attention Service Department E mail numark numark com
6. at each step in the audio chain Proper attention to the meter results in the punchiest possible sound without audible distortion 17 Power Switch and Power On LED DM1001X DM1002X FRONT PANEL DIAGRAM 1 Microphone Jack for a 1 4 Microphone connector 2 Crossfader Curve Adjust Switch CURVE SWITCH Postition Right The crossfader creates a short cut to bring in the opposing track to full volume prior to the mid point in the fader Position Left The crossfader creates a standard cut to bring in the opposing track to full volume at the mid point in the fader POSITION SWITCH RIGHT Fader Left mid point Right Track Track SWITCH LEFT Fader Left mid point Right Track Track 3 Headphone Jack for connecting headphones with a standard 1 4 stereo plug Numark The Proven Leader in Technology 1998 Numark Industries 7 http www numark com DM1001X DM1002X DM1001X DM1002X REAR PANEL DIAGRAM REAR PANEL INPUTS AND OUTPUTS 1 Power Connection Plug your power adapter in here See safety precautions on page 3 for proper treatment of the power cord 2 GND is the grounding lug for all turntables Always use this connection your turntable cable should have a grounding wire 3 The Stereo Main Outputs are low impedance RCA connectors controlled by the Master fader 4 The Record Outputs are designed to be hooked up to your tape deck s input jacks 5 The Phono Inputs us
7. e unbalanced RCA jacks Your input signal is fed directly to your mixer s high quality RIAA phono pre amplifiers so use this position only for moving magnet cartridges Line level sources will overload the sensitive phono pre amps and will sound very bad so always be sure to toggle the line phono switch over to line before connection of line sources 6 The Phono Line Inputs are unbalanced RCA jacks The Line Input is selected with the Line Phono Input switch above it You can connect stereo audio from HiFi VCRs cassette and reel to reel tape decks DAT machines CD players laser discs tuners even synthesizers or other mixing consoles NOTE Plug mono audio sources into both Left and Right inputs using a cable connector Warning make sure the LINE PHONO input switch is set to line before playing any line input level devices through your mixer 8 Line Phono Input switch Use this to allow line level equipment to be plugged into your phono inputs Numark The Proven Leader in Technology 1998 Numark Industries 8 http www numark com DM1001X DM1002X CONNECTION DIAGRAM 000000 0000 Numark The Proven Leader in Technology 1998 Numark Industries 9 http www numark com DM1001X DM1002X SPECIFICATIONS Inputs Line 10Kohm input impedance 1V rms sensitivity for 1 22V output Mic 10 Kohm input impedance unbalanced 2V rms sensitivity for 1 22V output 60mV rms max
8. k obligation under this warranty is limited to repairing or replacing at its option the product or part s therein which upon examination by Numark shall appear to be defective or not up to factory specifications providing the Numark product is returned transportation prepaid to Numark Numark shall not be liable for any damages consequential or otherwise resulting from the use and operation of this product and makes no other warranty s either express or implied on this product including any warranty of merchantability This warranty does not extend to any of our products which have been subjected to misuse neglect accident incorrect wiring not our own improper installation or use in violation of instructions furnished by us nor extended to units which have been repaired or altered outside of our factory nor to cases where the serial number thereof has been removed defaced or changed nor to accessories used therewith not of our own manufacture Numark reserves the right to make changes or improvements in its products during subsequent production without incurring the obligation to install such changes or improvements on previously manufactured equipment To place this warranty into effect the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries LLC within thirty 80 days after date of purchase This warranty gives you specific legal rights and you may also have other rights which vary from state to state
9. o rain or moisture Electrical equipment should NEVER be kept or stored in damp environments Please record the serial number your unit as Shown on the back of the chassis as well as the name dealer from whom you purchased the unit Retain this information for your records Please return the warranty card enclosed to register your unit with us PURCHASED FROM SERIAL NUMBER DATE OF PURCHASE Numark The Proven Leader Technology 1998 Numark Industries 2 http www numark com DM1001X DM1002X NUMARK DM1001X DM1002X STEREO MIXER INDEX Safety Information Page 2 Product Registration Introduction Page 4 Features Precautions Page 5 Face Panel Diagram Page 6 Operating Instructions Front Panel Diagram Page 7 Rear Panel Diagram Page 8 Connection Diagram Page 9 Specifications Page 10 Block Diagram Page 11 Warranty and Service Page 12 Numark The Proven Leader in Technology 1998 Numark Industries 3 http www numark com DM1001X DM1002X CONGRATULATIONS You have purchased the DM1001X DM1002X Stereo Mixer by Numark This equipment features a completely new design and the latest in manufacturing technology to give you greater quality and better reliability than ever before Your mixer gives your greater control than ever before in a compact and easy to use layout Enjoy your new mixer and remember BE CREATIVE Thank you for buying Numark DJ products
10. on that channel based on what you have connected to the rear panel input section 2 The Input Faders are low noise low impedance high quality smooth Alps faders These control individual source levels in the mix 3 Treble Middle and Bass Controls are for setting appropriate equalized levels for the music you are playing When turned all the way left they CUT the signal by for special effects mixing 4 Gain Controls are for accurately matching audio input levels of the channels 5 Microphone Controls are used to adjust input level and equalization level for your mic input The talkover feature will bring down the level of the music while keeping the mic level up This allows you to talk over the music 6 Microphone Jack for a 1 4 Microphone connector 7 KILL buttons DM1002X only are for instantly eliminating the chosen frequency area This way you can mix the bass of one song with the treble and middle of another 17 gt 4 A e 000 3 a 6 D CROSSFADER SECTION 8 The Replaceable Crossfader achieves clean segues between the two selected input channels Hard left selects Channel 1 Hard right selects the Channel 2 With the crossfader centered both channels are live Use the crossfader for fast and seamless segues from one selected channel to the
11. rized Numark Service Center A NOTE ON CABLES Make the input and output connections with readily available low capacitance stereo cables Quality cable makes a big difference in audio fidelity and punch See your Numark dealer electronics audio specialist store if you are not sure which cables to get DM1001X DM1002X SYSTEM PRECAUTIONS Use appropriate cables throughout your system Quality shielded audio cables and terminated shielded video cables low capacitance preferred Speaker cables must be 14 gauge minimum 12 or 10 gauge is better Reliability will be enhanced through the use of banana connectors on the speaker wires Observe correct speaker wire polarity If in doubt consult your Numark dealer or a qualified technician Take to connect only one cable at a time Pay attention to the color coded labelled Input and Output jacks ALWAYS remember TURN AMPS ON LAST AND OFF FIRST Begin with master faders volume controls on minimum and the amplifier gain input control s down Wait 8 to 10 seconds before turning up the volume This prevents transients which may cause severe speaker damage Use restraint when operating controls Try to move them slowly Rapid adjustments could damage speakers due to amplifier clipping Avoid amplifier clipping at all costs this occurs when the red LEDs usually on the front panel of mos
12. supply only of the type described in these operating instructions or as marked on the unit 8 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord 9 Object and Liquid Entry Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer 10 Damage Requiring Service This product should be serviced only by qualified personnel If you have any questions about service please contact Numark at the number s shown on the back cover of this manual 11 Grounding or Polarization Precautions should be taken so that the grounding or polarization means built into the mixer is not defeated 12 Internal External Voltage Selectors Internal or external voltage selector switches if any should only be reset and re equipped with a proper plug for alternative voltage by a qualified service technician Do not attempt to alter this yourself NOTE This apparatus does not exceed the Class A Class B whichever is applicable limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications WARNING To reduce the risk of fire or electric shock do not expose this appliance t
13. t professional power amplifiers start flashing Clipping is when the power amplifier is distorting and working beyond it s limits Amplifier distortion is THE major cause of speaker failure To prevent fire or shock hazard do not expose the unit to rain or moisture Never place cans of beer soda glasses of water or anything wet on top of the mixer Numark The Proven Leader in Technology 1998 Numark Industries 5 http www numark com DM1001X DM1002X DM1001X DM1002X FACE PANEL DIAGRAM GUIDED TOUR OF FEATURES AND OPERATING INSTRUCTIONS If this is your first mixer please read this entire manual before you begin operation If you are an experienced DJ we highly recommend reading the manual so you may fully appreciate this newer technology This mixer can be 10 rack mounted or used as a free standing unit Keep in mind that there are a few features you may never have seen before in a mixer of this type that you will need to read about INSTALLATION AND OPERATION Study the Connections Diagram on page 13 First connect all stereo input sources Next connect your microphone s and monitor headphones Make sure all faders are at zero and the unit is off Finally connect the stereo outputs to the power amplifier s and or audio sources Plug the mixer into AC power Now you are ready to switch it on CHANNEL FEATURES 1 Channel Input Toggle Switches select which source will be active
14. with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying this appliance FOR USA amp CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES _ FULLY INSERTED TO PREVENT BLADE EXPOSURE SAFETY INSTRUCTIONS 1 Read Instructions All the safety and operating instructions should be read before this product is connected and used 2 Retain Instructions The safety and operating instructions should be kept for future reference 3 Heed Warnings All warnings on this product and in these operating instructions should be followed 4 Follow Instructions All operating and other instructions should be followed 5 Water and Moisture This product should be kept away from direct contact with liquids 6 Heat Avoid placing this product too close to any high heat sources such as radiators 7 Power Sources This product should be connected to a power
Download Pdf Manuals
Related Search