Nortel Networks 1120SA IP Phone User Manual
Contents
1. and the displayed value will begin to flash a Press and hold for 3 seconds y I al ho N Use the 9 and amp keys to select the desired alarm value Press and hold both keys for one second to save this new value to memory and to exit this function The display will indicate Abr and then the new value TE pba The arrow pointing at the alarm bell will be activated Oo Alarm activation If the fuel remaining value drops below the fuel alarm value the alarm will sound and the alarm arrow will flash Press any key to mute the alarm The alarm arrow will continue to flash as long as the alarm condition remains Resetting the TRIP LOG or the TOTAL LOG To reset alog press the amp key until the display indicates the name of the log to be reset Press and hold both keys for three seconds Display will show ErP or kak for 2 seconds before resetting to zero lt 3 amp Press and hold for 3 seconds The trip log value may be reset without changing the total log value If the total log is reset to zero then the trip log will automatically reset to zero Note f the total log exceeds 999 then both it and the trip log will be reset to zero Northstar Explorer F210 Installation and Operation Manual 2 Instrument Setup Selecting units of measure The Explorer F210 will indicate fuel values in Litres Imperial gallons or US gallons To change the current setting perform the fol2. Explorer F210 L NORTHSTAR ON OFF AN v Explorer F210 Fuel Instrument Installation and Operation Manual Navaus NORTHSTAR www northstarnav com Northstar Explorer F210 Installation and Operation Manual IMPORTANT SAFETY INFORMATION Please read carefully before installation and use This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death WARNING indicates a potentially hazardous situation which if not avoided WARNING could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided CAUTION could result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially haz ardous situation which if not avoided may result in property damage DISCLAIMER It is the owner s sole responsibility to install and use the instrument and transducers in a manner that will not cause accidents personal injury or property damage The user of this product is solely responsible for observing safe boating practices BRUNSWICK NEW TECHNOLOGIES INC AND ITS SUBSIDIARIES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS DAMAGE OR THAT MAY VIOLATE THE LAW Governing Language This statement any instruction manuals user guides and other information relating to the p
3. amp circuit breaker electrical cables Avoid connecting the Connect the black wire to the electrical instrument to power circuits that share ground loads with ignition alternators inverters and radio transmitters Electrical power supply connections should always be as short as Connect the fuel flow transducer to the five pin transducer inlet cable possible BUZZER BRACKET 600mm 24 POWER CORD FUJI 5 PIN CONNECTOR Pa N RED BLACK TERMINAL TERMINAL Installation of the fuel flow transducer The fuel flow transducer is designed for Drain all the fuel from the flexible fuel line Cut installation in Coast Guard approved 9 5 mm the fuel line and using the fuel hose fixing clips flexible fuel line The transducer MUST be provided install the transducer so that the FUEL installed AFTER the main fuel filter It should be IN side of the transducer connects to the fuel located well away from any area where it will be tank effected by excessive heat or vibration from the engine It is preferable to mount the transducer in a vertical position Northstar Explorer F210 Installation and Operation Manual 9 Appendix A Specifications Display is backlit for Night Operation Change Value Up Size Mount 51mm diameter hole Depth behind face plate 95mm max Display 3 character LCD Colour Black with texture on bezel Backlighting Red coloured diffused lighting for display Water Integri
4. lowing steps 1 Power up the unit while holding down the D key J D Hold down during power up 2 When the unit is on release the amp key The display will indicate the current display unit 2 3 3 To select the display unit desired use the amp and E keys to change the value 4 To exit this mode press and hold both the amp and amp keys simultaneously for one second lt j amp Press and hold to exit CO C Imperial Gallons CO C US Gallons CO C Litres Information will now be indicated in the selected display unit Calibration The fuel transducer supplied with the fuel flow meter will provide readings at better than 5 accuracy Individual calibration will increase this level of accuracy to better than 2 over a fuel flow range of 10 0 to 120 litres per hour Use the following steps to calibrate your fuel flow meter 1 Reset the total log value to zero see previous page 2 Use a known amount of fuel The larger the amount the more accurate the calibration will be 3 Take note of the actual volume of fuel used and the fuel used indicated by the total log If these two totals are different the instrument may require calibration 4 Press and hold the key while applying power A Hold down during power up 5 Release the key Display will flash current total log value l ly L N 6 Use the Yor BW keys to make the display indicate the actual volume of f
5. ng Chart ssesssscsssscosscossscossscossscoosseosscoosssoosscoosscoossoosssoosssoosssoosssosssosssoosssoos 11 4 Northstar Explorer F210 Installation and Operation Manual 1 Operation Fuel Flow Press the amp key to display the current fuel flow rate S 86 8 Other Fuel Functions Press the EP key to cycle through the possible functions Each time the EP key is pressed the display will show an identifier for 2 seconds before the value is displayed Fuel used on trip Fuel used in total Low fuel alarm setting t GAS Fuel remaining in tank Changing the fuel remaining value To change the value of fuel remaining in the tank press the amp key until the display indicates GAS for two seconds and then displays the current OP Press and hold both keys for three seconds and the displayed value will begin to flash G Press and hold for 3 seconds x IN 7 N Use the and amp keys to change the value Press and hold both keys for one second to save this new value to memory and to exit this function The display will indicate GAS and then the new value Northstar Explorer F210 Installation and Operation Manual 5 Setting the low fuel alarm Use the amp key to select the alarm function The LCD will indicate Abr for two seconds and will then display the present alarm value If no alarm value has been entered the LCD will indicate BFF Press and hold both keys for three seconds
6. ntenna e Increase the separation between the equipment and receiver e Connect the equipment into an output on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced technician for help e A shielded cable must be used when connecting a peripheral to the serial ports Northstar Explorer F210 Installation and Operation Manual 3 Contents RIE UT AEEA E EAEE soxcescabchucestanvacsstase E A E E 5 FRC IOUN e rna a a a ine ces aaa ee aa eA 5 Other Fuel Func oN sdei a a a TE meen a a 5 Changing the fuel remaining Value cece cece cece eee e eens eee eeeeeeeeaeneees 5 Setting ThE low Tue Alaris sa6 tascsb2esdcavera dead aeasdtiauc seed ieed nears aaeiaeee 6 Alarmi activat ON Giks sicds seein Since vats Shee wes Ro eeeboeredndhee nes Ghd es eet Routes 6 Resetting the TRIP LOG or the TOTAL LOG c ccc ceecceeeeeeeceeeeeeeaeeenaes 6 Z ns tumnment Setiana a 7 Selecting units Of MEASULE narida A AO 7 Calibration a eE AT EEO TAE ET a a a a 7 3 mistalatioM annann AAAA AA 8 Location aaen a a EA T alee Aes EA T A okt Sea EANA 8 MOUNINO enana E ER E mG a E E S E 8 WIRING CONNEC e aneirin a a a tated ads 9 Installation of the fuel flow transducer cece eee c eee c cece cece eeeeeceeeceeees 9 Appendix A Specifications secssveccussvessceusessscuseradducsscpeecveds tssesssnscdasvbenoddecssecasinisadidsesesved sodsesteecaseisideesis 10 Appendix B Troubleshooti
7. roduct has been translated from another language Translation In the event of any conflict between any Translation of the Documentation the English language version of the Documentation will be the official version of the Documentation This manual represents the Explorer F210 as at the time of printing Brunswick New Technologies Inc and its subsidiaries and affiliates reserve the right to make changes to specifications without notice Copyright 2006 Brunswick New Technologies Inc Northstar is a registered trademark of Brunswick New Technologies Inc Documentation may be translated to or A N FCC Statement Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a normal installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving a
8. ty Front will withstand direct water spray Alarm Audio and visual alarm indicates remaining fuel total has dropped below a preset alarm value Flow 2 5 to 160 litres per hour 0 5 to 43 US gallons per hour 0 4 to 36 imperial gallons per hour Logs Logs record fuel used up to 999 display units Total Log is saved in memory at power down Both Trip Log and Total Log can be reset via the keypad NORTHSTAR Fuel Remaining User enters a fuel value into memory via the key pad The quantity of fuel used is automatically subtracted from this total This value remains in memory at power down Operating Voltage 8V DC to 16 5 V DC Operating Temperature O to 50 C 32 to 122 F Current Drain 70 MA max RF Interference lt 6 dB quieting on any marine radio channel with 3 dB gain antenna within one metre of the instrument Complies with CE EMC standards EN50081 1 and EN50082 1 Change Value Dow Northstar Explorer F210 Installation and Operation Manual Appendix B Troubleshooting Chart No display 1 Check DC power connections and DC polarity with voltmeter 2 Check fuse No flow reading indicated 1 Check connection to flow transducer 2 Remove transducer from fuel line blow through transducer a whistling noise will indicate the turbine is rotating Low flow reading indicated 1 Check that the gauze filter is clean If the filter is not installed fine strands may clog up the t
9. uel used 7 Press both keys simultaneously for 1 sec to exit lt 3 amp Press and hold for 1 second The fuel flow meter is now calibrated Northstar Explorer F210 Installation and Operation Manual 7 3 Installation WARNING IT IS VERY IMPORTANT TO INSTALL A FUEL FILTER BETWEEN THE FUEL FLOW TRANSDUCER AND THE FUEL TANK THIS FILTER WILL CATCH LARGER PARTICLES OF DIRT FROM THE FUEL TANK AND PREVENT THE FINE GAUZE FILTER IN THE FUEL FLOW TRANSDUCER FROM BECOMING BLOCKED AS THIS MAY DAMAGE THE ENGINE Location Mounting The Explorer F210 is designed for above or below The instrument panel must be 3mm to 19mm deck installation Select a position that is to in thickness On a flat surface Drilla 51mm 2 hole in the instrument panel At least 300mm 12 from a compass Remove brackets and insert the instrument At least 500mm 20 from any radio so the back is flush with the instrument panel Easy to read by the helmsman and crew Slide the bracket over the instrument and tighten the mounting nut until secure Protected from physical damage J g Accessible to electrical cable connections Instrument a Panel 51mm 2 Mounting Bracket Gasket 8 Northstar Explorer F210 Installation and Operation Manual Wiring Connection Keep electrical and transducer cables away Connect the red wire to the positive supply from alternator or other noise generating via a 1 amp fuse or a 1
10. urbine 2 Check calibration is correct High or erratic reading Check fuel connections are well made Air in fuel lines will cause erratic or high readings Northstar Explorer F210 Installation and Operation Manual AMERICAS 30 Sudbury Road Acton MA 01720 USA Ph 1 978 897 6600 Ph 1 800 628 4487 Fax 1 978 897 7241 sales bntmarine com EUROPE Unit 2 Ocean Quay Belvidere Rd Southampton S014 5QY ENGLAND Ph 44 2380 339922 Fax 44 2380 330345 northstaruk northstarnav com AUSTRALIA PO Box 479 Gladesville NSW 2111 AUSTRALIA Ph 61 2 9879 9060 Fax 61 2 9879 9009 northstaraus northstarnav com NEW ZEALAND PO Box 68 155 Newton Auckland Auckland NEW ZEALAND Ph 64 9 481 0500 Fax 64 9 481 0590 northstarnz northstarnav com www northstarnav com NORTHSTAR FE CEO Made in New Zealand MNO00207A
Download Pdf Manuals
Related Search