Nissan 2011 Sentra Automobile User Manual
Contents
1. INSTALLATION INSTRUCTIONS 98 99 NISSAN FRONTIER 4 WD KIT 4083 AAWARNING Installation of a Performance Accessories body lift will change the center of gravity and the handling characteristics of the vehicle Because of the higher center of gravity and larger tires the vehicle will handle and react differently both on and off road You must drive it safely Extreme care must be taken to prevent vehicle rollover or loss of control which could result in serious injury or death Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened AAWARNING Read and understand all instructions warnings cautions and notes in this sheet and in your owners manual before you begin the installation of this body lift kit A CAUTION Proper installation of a Performance Accessories body lift kit requires knowledge of the factory recommended procedures for disassembly an assembly of original equipment components It is recommended that the factory shop manual and any special tools necessary to your vehicle be on hand during the installation Installation of this body lift kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of you vehicle It is strongly recommended that a certified mechanic who is familiar with the installation of similar components install this body lift kit AAWARNING This body lift kit sh2. You may want to wrap a rag around the bottom of the shift lever to prevent any oil from dripping on the carpet Pull the carpeting back to expose the two body mounting bolt access covers Remove the plastic access covers from the floorboard and discard Be sure that the transmission is in neutral Remove the shift lever from the transmission AAWARNING Use extreme caution when working near fuel lines and fuel tank Clean up spilled fuel immediately Any spark could cause an explosion or fire resulting in serious personal and property damage 15 Remove the screws that mount the fuel filler neck to the body Loosen the hose clamp that mounts the filler hose to the fuel tank Loosen the clamp that mounts the vent hose to the tank Remove the entire filler neck and hose assembly from the vehicle 16 Disconnect the license plate lights from the rear bumper Remove the six bolts that mount the rear bumper to the frame Remove the bumper from the vehicle 17 Measure the distance between the cab and the bed Record this measurement to insure proper alignment of the cab and bed after the lifting operation has been completed Remove the bolts at the rear cab mount that mount the body to the side of the rear cab mount There are two bolts inserted from the inside of the frame mount and are threaded into the body There are two more bolts that are inserted from the bottom and thread into the mounting pad When the rear cab bolt is removed t
3. of the line to gain more slack in the line 27 Check the a c line at the core support Be sure that there is enough slack in the line to remount it to the core support If there is not enough slack carefully bend the line to gain more slack Be sure that there is ample slack in the line Install the bolt that mounts the a c line to the core support Tighten securely 28 Using two 10mm 1 25 x100 bolts with a 3 8 washer on each bolt and the two 3 long tubes mount the cab safety loop to its original location It may be necessary to bend the loop slightly to align the loop to the mounting holes with the spacer tubes installed Tighten safety loop mounting bolts securely AAWARNING Use extreme caution when working near fuel lines and fuel tank Clean up spilled fuel immediately Any spark could cause an explosion or fire resulting in serious personal and property damage 29 Lengthen the fuel filler hose Cut the filler hose toward the bottom below the first bend Install the 1 3 4 fuel filler extension between the two sections of the filler hose Install a 28 hose clamp at each end of the extension Tighten both hose clamps securely Remove the vent hose from the filler neck Install the new vent hose to the filler neck vent Install a 10 hose clamp and tighten securely Install the filler assembly in the vehicle Using the stock clamp reconnect the filler hose to the fuel tank Using a 10 hose clamp reconnect the la
4. 10mm bolt the bolt should be inserted from the bottom through the outside support bracket the bottom stock bushing the frame perch the stock top bushing the block and threading into the nut that is captured inside the body Reinstall the two bolts that mount the outside support bracket to the bottom of the frame perch Do not tighten any of the bolts at this time 19 Repeat step 18 for the driver s side of the cab Adjust the cab to bed clearance Install the outside support plates to the cab using the stock bolts Attach the outside support plates to the stock outside support brackets using two 7 16 x 1 bolts four 7 16 SAE washers and two 7 16 nylock nuts on each side of the cab and tighten securely Remove cab mounting bolts one at a time apply Loctite reinstall bolt and tighten to vehicle torque specifications 20 Loosen but do not remove all six bed mounting bolts Remove the mounting bolts from the passenger side of the bed only Using a hydraulic jack and a wooden block slowly lift the passenger side of the bed just high enough to place the spacer blocks on the frame Install the new mounting bolts in the following positions 4 x 5 at the front bed mount 2 x 4 4 at the middle bed mount and Ye x 5 1 2 at the rear bed mount The bolts should have a Ye USS large washer installed and then the bolt should be inserted through the thick rubber bushing through the frame through the thin rubber bush
5. ake lines on the passengers side front wheel well Disconnect the brackets that mount the steel vacuum lines to the passenger side frame rail from the frame rail Check along the fender well and under the intake manifold to be sure that there is enough slack in the vacuum lines to allow lifting Disconnect the lines as necessary Make a diagram to insure proper reconnection after the lifting operation is complete 11 Remove two bolts that mount cab safety loop to floorboard around driveline through the cross member 12 Remove the two screws one on each side that mount the outside of the bumper to the fender These 98 99 Frontier Kit 4083 screws are accessed through the wheel well Remove the four bolts that mount the front bumper to the frame Remove the bumper from the vehicle 13 Remove the tabs that hold the fender well flaps to frame This will prevent flaps from being damaged while lifting 14 Remove the screws that mount the scuff plate to the door jamb area on both sides of the vehicle Remove the kick panels from both sides Place the manual transmission in neutral Remove the screws that mount the shift boot to the floorboard Pull the boot back to expose the top of the transmission Remove the c clip that holds the transmission shift lever in the top of the transmission Remove the spacer washer that is under the C clip Unbolt the transfer case shifter from the transfer case Remove both levers from the vehicle
6. and replace the cover Install the spacer shim Install the retaining clip Bolt the transfer case shifter to the transfer case and adjust the linkage as outlined in the factory repair manual Check the shift lever and transfer case shifter operation Be sure that there is complete engagement in all gears and ranges Replace the shift boot and housing assembly Tighten all mounting screws securely Check the shift lever and transfer case shifter operation again 32 Replace the carpet and matting to its original position Replace both kick panels and both doorjamb scuff plates Tighten the mounting screws securely 33 Using the stock bolts mount the front bumper brackets to the frame Tighten the mounting bolts so the brackets cannot move but so the bumper can still be adjusted Slide the front bumper onto the relocating brackets Align the holes in the stock bumper brackets with the holes in the new bumper brackets Reinstall the bumper on the vehicle Mount the bumper to the relocating brackets using two 7 16 x 1 bolts four 7 16 USS large washers and two 7 16 nylock nuts Adjust the bumper to body clearance Tighten all bumper mounting hardware securely Reconnect the wires to the driving lights AAWARNING Raising the rear bumper is intended to enhance the appearance of the vehicle only The rear bumper will no longer be rated for towing of any kind Attempting to tow with the rear bumper after it has been raised can res
7. haft Install the retaining bolt in the steering extension Do not tighten the retaining bolt at this time Be sure that all marks are properly aligned and that there is ample engagement at all unions 23 Using the new lower radiator support as a template Mark the lower core support for alignment of the new support Align the holes in the new bracket with the stock mounting holes Mark the core support for proper alignment of the new support after the stock mount has been removed Using a die grinder or hacksaw cut away the bottom radiator mount from the core support Be especially careful of the a c condenser when cutting the sheet metal Cut to the outside of each mounting hole approximately 1 to 2 and flush with the vertical surface of the core support allow enough room for the radiator to slide past the remaining sheet metal without hitting Place the new lower radiator support bracket on the core support Be sure that the bracket is aligned with the marks made earlier and that the bracket is positioned flush against the core support with the lip resting on top of the core support Using the bracket as a template mark the top of the core support through the holes in the bracket Remove the bracket Drill a 1 hole at both locations Mount the bracket to the core support by install a x 1 bolt with a 1 4 washer through the bracket and the core support Install a 4 washer and nylock nut on the bolt from the bottom of
8. he bracket can be removed Loosen but do not remove all six cab mounting bolts They are located as follows in the front fender well in the front floorboard and at the rear of the cab screwing up into the cab The front two mounting bolts are installed from the top and the rear bolt is installed from the bottom AAWARNING Failure to replace the OEM body mounting hardware except mounting bolts in the stock locations could result in damage to the vehicle and possible personal injury 18 Using a hydraulic jack and a wooden block slowly lift the passenger side of the cab just high enough to put the spacers on the mounting pads Continually check for any hoses wires etc to be sure that everything is flexing properly and not binding Be especially careful of the a c hose at the firewall and at the core support Place the spacer block on top of the mounting pad Using a 3 8 washer in conjunction with the stock washer install the 7 16 x 7 bolts at the front two mounts core support and front floorboard and the 10mm x 180mm bolt at the rear cab mount For the front two mounts the 3 8 washer should be installed on the bolt The bolt should then be inserted from the top through the stock top washer through the body the spacer the factory top bushing the frame perch the bottom factory bushing the stock bottom washer and inserted into the 7 16 nylock nut provided with the kit The 3 8 washer should be installed on the
9. ing through the spacer and through the bottom support rail of the bed Install a 1 2 USS washer and nylock nut on each bolt Do not tighten at this time 21 Repeat step 20 for the driver s side of the bed Realign the bed to the cab Refer to the measurements 98 99 Frontier Kit 4083 made earlier One by one remove each bed mounting bolt Remove bed mounting bolts one at a time apply Loctite reinstall bolt and tighten to vehicle torque specifications AAWARNING Failure to install the steering extension properly could result in loss of steering causing damage to the vehicle and possible personal injury 22 Install the steering extension into the lower coupler of the steering shaft Be sure that the extension is installed so the mounting bolt will slide across the flat on the steering extension Install the stock retaining bolt in the steering shaft If the bolt will not easily slide across the flat on the steering extension the extension has been installed incorrectly Do not tighten the retaining bolt at this time Extend the mark on the lower part of the steering shaft down onto the extension Install the upper part of the steering shaft into the upper coupler inside the engine compartment Be sure to align the marks made earlier Install the stock retaining bolt in the upper coupler Align the mark on the steering extension with the mark on the gearbox Install the steering extension on the gearbox splined s
10. ing system spill Antifreeze can be harmful to the environment Take care to store the drained antifreeze coolant in a place away from children and animals Antifreeze coolant can be fatal if swallowed 6 Drain the radiator into a clean container Be sure that the radiator has cooled sufficiently to safely open the cooling system Remove the fan shroud from the radiator After the radiator has drained completely loosen the clamp that mounts the upper radiator hose to the radiator Remove the hose from the radiator Loosen the clamp that mounts the lower radiator hose to the radiator Remove the hose from the radiator Remove the bolts that mount the fan shroud to the radiator Remove the bolts that mount the top two radiator mounts to the core support Remove the mounts from the vehicle Lay the fan shroud against the engine Pull the radiator up and out of the bottom mount Remove the radiator from the vehicle 7 Loosen the two hose clamps that mount both heater hoses to the heater core at the firewall Release the heater hoses from the clamps on the firewall to allow lifting 8 Remove the bolt that mounts the a c hose to the firewall close to the vacuum brake booster 9 Unbolt the power steering reservoir and bolt the extension bracket to the truck using the stock bolts Bolt the reservoir to the extension bracket using three 1 4 x 1 bolts six 1 4 washers and three 1 4 nylock nuts 10 Remove the guard protecting the br
11. iving the vehicle 3 Disconnect both battery cables Be sure to disconnect the negative cable first then the positive cable Remove the airbag fuse from the fuse box Consult the vehicle owner s manual for the exact location of the fuse 4 Remove the air cleaner housing from the throttle body Remove the bolts that mount the air duct to the upper radiator mount Remove the air cleaner and air duct from the vehicle A CAUTION Be sure that the steering shaft does not turn independently of the steering gearbox This could cause the air bag system to malfunction causing possible personal injury and damage to the vehicle 5 Mark the steering shaft where it slides into the upper coupler Mark the lower coupler and the gearbox where the steering shaft slides onto the gearbox splined shaft This insures proper alignment of the steering after the steering extension has been installed Remove the bolt that mounts the steering shaft to the upper coupler 2 Remove the bolt that mounts the steering shaft to the gearbox splined shaft Slide the steering shaft up and off the gearbox splined shaft then out of the upper coupler Remove the shaft from the vehicle AAWARNING Use extreme caution when working with the engine cooling system Never remove the radiator cap from a hot radiator Wait until the engine and radiator has cooled and the pressure in the system has dissipated Use care not to any antifreeze coolant while drain
12. ould only be installed on vehicles that are in good working condition Before the installation begins the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts This body lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused Off road use of your vehicle with this body lift installed may increase the stress applied to the factory body mounts It is not recommended that any vehicle with a body lift installed be involved in any extreme off road maneuvers such as jumping Failure to follow this warning may result in serious personal injury and or serious damage to your vehicle AAWARNING Performance Accessories strongly discourages the use of a suspension lift kit or any other lift device in addition to a body lift kit A vehicle that uses a combination of lift devices not originally engineered to be used together may result in unexpected and unsafe handling characteristics Many states now have laws restricting bumper heights and vehicle lifts Local laws should be consulted to determine if the changes you intend to make to your vehicle complies with state laws ZAWARNING The installation of larger wheel and tire combinations may reduce the effectiveness of the Anti lock Braking System ANOTE Performance Accessories recommends using the Loctite supplied in the kit on all hardware unless noted in the instruc
13. r Extension Tube Hose Extension Fan Shroud Heater THA DRDDOANNN AND oO AMYONMNOAOAHRH OOP moot NyNy ARO Rev 03 Copyright 04 06 Performance Automotive Group 98 99 Frontier Kit 4083
14. rge vent hose to the fuel tank Tighten all hose clamps securely Install the screws that mount the filler neck to the body Tighten 98 99 Frontier Kit 4083 securely Replace the fuel cap AAWARNING A certified welder should perform all welding 30 Lengthen the transmission shift lever Scribe a line along the side of the shift lever below the bend Be extremely careful during this procedure to not damage any of the parts that are attached to the shift levers Cut the lever into two pieces through the line Insert the shift lever extension between the two parts of the shift lever The tapered end of the extension goes toward the bottom Both parts of the shift lever should slide into each end of the extension Be sure that the lever is all the way in the extension and that the scribe lines are aligned with the mark on the extension Using the holes in the extension as a guide drill a 1 8 hole through each part of the shift lever and the opposite side of the extension Install a 1 8 x 3 2 roll pin at both ends of the extension To lengthen the transfer case lever scribe a line along the shaft above the two bottom bends and cut the shaft through the scribed lines Place the extension pin between the two pieces and align the scribed lines before welding the extension in place 31 Replace the shift lever in the vehicle Insert the transmission shift lever into the top of the transmission Be sure that it is all the way in
15. the core support Tighten the Yq hardware securely 24 Install the radiator on the new lower support bracket Remove the two rubber bushings from the plastic studs on the top of the radiator Install the rubber bushings into the large hole in the 2 x 3 x 1 rectangular tube Slide the tube with the rubber bushing onto the studs at the top of the radiator Reinstall the stock upper radiator mount The hole in the stock mount should align with the hole in the tube Mount the tube to the stock bracket using a 3 8 bolt two 3 8 USS washers and a 3 8 nylock nut on each side Do not tighten at this time Be sure that the radiator is secure Tighten all radiator mounting hardware securely Install the fan shroud to the radiator using the stock hardware Check the fan to fan shroud clearance Be sure that the fan cannot make contact with the shroud Tighten the fan shroud mounting hardware securely Install both radiator hoses to the radiator Tighten the hose clamps securely 25 Fill the cooling system as much as possible at this time It will need to be topped off after the vehicle has been started 26 Reroute the vacuum brake booster hose over the a c hose at the firewall Bend the bracket that mounts the a c hose to the firewall forward to a 45 degree angle This should give the hose ample slack Reconnect the hose to the brake booster If the line still feels tight it may be necessary to carefully bend the steel portion
16. the proper level Reinstall the radiator cap Carefully check all hoses to be certain that they have been connected properly and that there is ample slack With the amount of hoses on this vehicle it is vital that this be checked thoroughly Test drive the vehicle in all gears and 4 wheel drive ranges Pay very close attention to all vehicle systems Check all hardware again in 500 miles and as part of your regular maintenance schedule A CAUTION Performance Accessories does not recommend any particular wheel and tire combinations for use with its body lifts and can not assume responsibility for the customer s choice of wheels and tires Your owner s manual can be referenced for recommended tire sizes and warnings related to the use of oversized tires Larger wheel and tire combinations increase stress and wear on steering and suspension components which leads to increased maintenance and higher risk for component failure Larger wheel and tire combinations also alter speedometer calibration braking effectiveness center of gravity and handling characteristics Consult with an experienced local off road shop to find what wheel and tire combinations work best with your vehicle All warranty information instruction sheets and other documents regarding the installation of this product must be retained by the vehicle owner Information contained in the instructions and on the warranty card will be required for any warranty claims The
17. tions AWARNING Always wear eye protection when operating power tools 98 99 Frontier Kit 4083 1 Read all warnings and instructions completely and carefully before you begin Check the kit for proper contents refer to the part s list Only attempt to install this kit on the vehicle described above If anytime during the installation you encounter something different from what is outlined in the instructions call technical support 928 636 7080 If parts are missing from kit please be prepared to provide the following information 1 Name of purchase location 2 Bar Code on side of box 3 Date above bar code 4 Date inside box cover 5 Inspector from inside box cover A WARNING Make sure that your vehicle is properly blocked and secured before you begin installation of this lift kit 2 Park the vehicle on a clean dry flat level surface Block the tires so the vehicle cannot roll in either direction AAWARNING The Supplemental Restraint System SRS air bag must be deactivated during installation of the lift kit to avoid accidental deployment of the air bag while working near SRS sensors and wiring Do not allow anyone near the air bag during installation of the lift kit Accidental deployment can result in serious personal injury or death Refer to your factory service manual for the recommended procedure to disable the SRS before installation of lift blocks The SRS must be reactivated before dr
18. ult in damage to the vehicle and possible personal injury A class III receiver hitch must be installed in order to tow with the vehicle after the rear bumper has been raised 34 Install the rear bumper If you wish to tow with the rear bumper reinstall the bumper in the stock location using the stock brackets and mounting hardware To raise the rear bumper remove the two bolts that mount each rear bumper bracket to the bumper Drill a new mounting hole in the bumper side of the stock bumper Hold the bumper bracket against the frame in the stock location Pivot the rear of the bracket upward until the last hole on the bracket is aligned with the bottom of the slotted hole in the frame The first hole in the bracket should still align with the last stock hole in the bumper The center mount hole should also align with a hole in the frame Mount the brackets to the frame using the 7 16 x 1 bolts 7 16 USS washers and 7 16 nylock nuts provided Do not tighten Mount the bumper using the 7 16 x 1 bolts 7 16 USS washers and 7 16 nylock nuts provided The rear bumper should align with body Adjust the bumper to body clearance Tighten all bumper mounting hardware securely Reconnect the license plate lights to the bumper 35 Reinstall the air cleaner Install the top of the housing Install the air intake duct to the upper radiator mounting brackets Install the mounting screws and tighten securely AAWARNING All
19. vehicle owner needs to understand the modifications that have been made to his vehicle and how they affect the handling and performance of the vehicle Failure to provide the customer with this information can result in damage to the vehicle and possible personal injury Kit Parts List Quantity Description 3 x 3 blocks 3 x 2 blocks 3 Lower Radiator Support Bracket Front Right Bracket Front Left Outer Cab Support Plates Bracket Power Steering Reservoir Bracket Parking Brake Spacers Bed W Holes Spacers Bed W O Holes Extension Fuel Filler Extension Shift Hose Rubber 1 19 Hose Rubber 14 17 Instruction Sheet Loctite Logo Label Warning Label MWe er eae tt SPP AN SP TAN TAHT olt Pack Bolt M10 1 25 x 180 Fine Thread Bolt 7 16 14 x 7 Bolt 13 x 4 1 2 Bolt 13 x 5 Bolt 13 x 5 1 2 Nut Nylock 2 13 Washer 2 USS Washer 2 Thick Nut Nylock 7 16 14 Washer 3 8 USS Bolt 3 8 24 x 1 1 4 Steering Extension ardware Pack Bolt M10 1 25 x 100 Fine Thread Bolt 4 20 x 1 Nut Nylock 14 Washer 4 SAE Bolt 5 16 18 x 1 Nut Nylock 5 16 18 Washers 5 16 USS Bolt 3 8 16 x 1 Nut Nylock 3 8 16 Washer 3 8 USS 16 Bolt 7 16 14 x 1 16 Nut Nylock 7 16 14 24 Washer 7 16 USS Washer 7 16 SAE Clamp Hose 6 Clamp Hose 10 Clamp Hose 28 Pin Roll 1 8 x 1 Extension 3 Shift Pin Hose Vacuum Extension Tube Hose Heate
20. welding should be performed by a certified welder only 36 Install the four bed overload pads on the frame over the wheel wells Remove the rubber pads bolted to the frame and place the overload pads where the rubber pads were The pads need to be tack welded to the frame only 37 Reconnect both battery cables Be sure to reconnect the positive cable first then the negative cable Reinstall the airbag fuse if equipped 38 Place the warning sticker on the dash in plain sight of all vehicle occupants A CAUTION All fasteners should be retorqued after 500 miles and after off road use All body lift components should be visually inspected and fasteners retorqued during routine vehicle servicing 98 99 Frontier Kit 4083 39 Double check the vehicle Check all mounting hardware to be sure that it is properly tightened Check all wires hoses cables etc to be sure that there is ample slack Check the vehicle electrical system Start the vehicle Check the steering in both directions to be sure that there is no bind Check clutch operation Check the operation of the brake system and the parking brake Check both shift levers operation Be sure that there is proper engagement in all gears and 4 wheel drive ranges Check coolant level Caution never open a closed cooling system after the vehicle has been started Only fill the cooling system if the cap has been removed while the vehicle was still cold Fill the coolant to
Download Pdf Manuals
Related Search