Morphy Richards RN40630 MUK REV2 Iron User Manual
Contents
1. RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 age 1 morphy richards Register online for your 2 year RS guarantee See back of this s instruction book for details UK and Ireland customers only www morphyrichards co uk upto 2year Upon registration with Morphy Richards UK amp RO ol TurboSteam iron steam spray shot Cli Please read and keep these instructions Getting the best from your new iron Safety first Caution must be used when handling this appliance as it does get very hot Always switch off the unit and allow to cool before cleaning or storing To improve the life of your new product and to ensure the cleanliness of your clothes we strongly recommend the use of distilled or demineralised water cE If you have a problem or complaint please call our dedicated UK based helpline before returning your product to the retailer from where it was purchased UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 B Ireland Helpline 1800 409 119 RN40630 MUK Rev2 For details of other Morphy Richards products plus replacement parts and www morphy accessories please see our website RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 Page 2 IMPORTANT SAFETY INSTRUCTIONS e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience or knowledge2. if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision e Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down The iron must not be left unattended while it is connected to the supply mains e The plug must be removed from the socket outlet before the water reservoir is filled with water e The iron must be used and rested on a stable surface e When placing the iron on its heel ensure that the surface on which the heel is placed is stable e The iron is not to be used if it has been dropped if there are visible signs of damage or it is leaking The use of any electrical appliance requires the following common sense safety rules Primarily there is danger of injury or death and secondly the danger of damage to the appliance These are indicated in the text by the following two conventions WARNING Danger to the person IMPORTANT Damage to the appliance In addition we offer the following safety advice UK Helpline 0844 871 0960 Replacement Parts 0844 8730726 Ireland Helpline 1800 409 119 RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 age 3 B Location E Children i Personal Safety Do not use outdoors or near water IMPOR
3. lt Steam shot of steam gt lt Dry ironing spray gt Without water in tank lt Dry ironing gt UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 E COMPONENTS OF YOUR IRON Steam boost button Water spray button Variable steam switch Filling hole with cap Spray nozzle Soleplate Temperature dial Temperature indicator light Water tank Life long anti scale certain models only Filling beaker 00 O0O0OO0O0OO0OO0OO0OO0OO0OO Auto shut off indicator certain models only Soleplate zones Turbo Boost Powerful boost of steam gets into the trickiest of places Constant Steam Removes all creases at a level you control Ireland Helpline 1800 409 119 RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 age 5 I BEFORE USE Sort out the items to be ironed according to the type of fabric This will minimise the frequency of temperature adjustment for different garments Note The steam facility should only be used on garments which are suitable for ironing at 3 dot and MAX settings see Temperature guide on page 3 Textiles and clothes are supposed to carry ironing instructions If they don t you should follow the fabric guide on page 3 but be sure to test the temperature by ironing the hem of the garment or similar discreet area first If you turn the control dial down from a hot setting to a cooler setting wait until the iron temperature h
4. high by moving the variable steam control When using the iron at the bottom of the steam range the steam output should be adjusted to the low setting The steam facility should only be used on garments which are suitable for ironing at 3 dot and MAX settings E Steam boost i Press the steam boost button to obtain a boost of extra steam for ironing out creases in heavy material such as denim etc The shot of steam can be used whilst dry ironing providing there is water in the tank and the temperature control is set within the steam range Do not use shot of steam at temperatures below the steam range shown on the control dial Note For optimum steam quality do not operate the shot more than three times in succession E Vertical steam Hold the iron in a vertical position between 1cm and 2cm away from the item d Press the steam boost button this will create vertical steam UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 This feature is especially useful for removing creases from hanging clothes curtains wall hangings etc Note For optimum steam quality do not operate the shot more than three times in succession H No drip system certain models only The no drip system is designed to prevent water escaping from the soleplate when the iron is too cold During use this feature may emit a loud click particularly during heat up or whilst cooling down This is perfectly
5. Richards individually Please note that the 2 year guarantee is only available in the UK and Ireland Please refer to the one year guarantee for more information E YOUR ONE YEAR GUARANTEE It is important to retain the retailer s receipt as proof of purchase Staple your receipt to this back cover for future reference Please quote the following information if the product develops a fault These numbers can be found on the base of the product Model no Serial no All Morphy Richards products are individually tested before leaving the factory In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced If the fault develops after 28 days and within 12 months of original purchase you should contact the Helpline number quoting Model number and Serial number on the product or write to Morphy Richards at the address shown You may be asked to return a copy of proof of purchase Subject to the exclusions set out below see Exclusions the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt If for any reason this item is replaced during the 1 year guarantee period the guarantee on the new item will be calculated from original purchase date Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase To q
6. TANT Do not use the product on a surface which could be damaged by heat or steam such as a worktop or a polished wood surface Close supervision is necessary when any appliance is used near children Children do not understand the dangers associated with operating electrical appliances Children should be supervised to ensure that they do not play with this appliance WARNING Burns can occur from touching hot metal parts hot water or steam Use caution when you turn a steam iron upside down there may be hot water in the water tank WARNING To protect against the risk of electric shock do not put the appliance in water or in any other liquid Do not use the vertical steam feature on clothes that are being worn Never allow the mains lead to over hang the work surface The socket should always be off before plugging or unplugging from the socket Never yank the cord to disconnect from the socket instead grasp the plug and pull to disconnect Do not allow the cord to touch hot surfaces e Let the iron cool completely e before putting away Loop the cord loosely around the iron before storing E Other safety considerations e Use the iron only for its intended use e Always disconnect the iron from the electrical socket when filling with water or emptying and when not in use e f the supply cord is damaged it must be replaced by the manufacturer its service agent or similar
7. ain models only that any drops of water In the unlikely event of any remaining cannot leak out and man made fibre fusing to the discolour the soleplate soleplate set the iron at the 3 dot position and pass it over a IMPORTANT The flex can be clean piece of cotton which will damaged if wound too tightly draw the deposit off the surface around the iron after use Make a loose loop with the flex and Do not use scouring powder or wrap it around the iron The iron solution as this could cause must be cool before winding the damage to the coating flex and storing on its heel Use the plastic clip provided to secure the cable to the iron H To clean a stainless steel soleplate _teerainmodesonyy BL HELPLINE To keep the soleplate of your iron If you have any difficulty with clean and free of limescale we your appliance do not hesitate recommend that you use one of to call us the gentle chrome silver or stainless steel cleaners that are We are more likely to be able to generally available Always follow resolve any issues than the the manufacturer s instructions store from where you bought it To clean off melted man made Please have the following fibres set the iron at the 3 dot information ready to enable our position and pass it over a clean staff to deal with your query piece of cotton which will draw quickly the deposit off the surface e Name of the product To clean a non stick e Model number as shown on co
8. as stabilised before you continue ironing Delicate fabrics such as silk wool velour etc are best ironed with an ironing cloth to prevent shine marks B FILLING A 1 Make sure that the iron is not plugged in then set the steam dial to O position H before filling the iron with water 2 Lift the filler cap until it locks and holds in the open position Fill the water through the filling hole into the water tank using the beaker provided EN The tank holds 350ml of water The iron is fitted with a clear view water tank so you can easily see the water level when filling During filling tilt the iron forward to read the water level The MAX mark is printed on the side of the clear view tank E After filling push the filler cap forward until it clicks in place IN HARD WATER AREAS THE USE OF DISTILLED OR DEMINERALISED WATER IS RECOMMENDED Never use battery topping up fluid or water containing any substances like starch or sugar or defrosted water from a refrigerator 3 Always pour out the remaining water after use WARNING When filling your iron with tap water always use the beaker provided Never fill directly under the tap E TEMPERATURE CONTROL 1 Plug in the iron and switch on the power at the mains socket 2 Set the temperature dial to the temperature required d but don t start ironing immediately If you wait a few minutes the iron will stabilise at the requ
9. ated soleplate underside of the appliance certain models only e Serial number as shown on In the unlikely event of any underside of the appliance man made fibre fusing to the soleplate set the iron at the 3 dot UK Helpline 0844 871 0960 position and pass it over a clean piece of cotton This will draw the Replacement Parts 0844 873 0726 deposit off the surface Ireland Helpline 1800 409 119 Do not use scouring powder or solution as this could cause damage to the coating E WEBSITE You may also contact us through E To clean the exterior our website or visit the site to browse and purchase appliances Allow the iron to cool and wipe spare parts and accessories from over with a damp cloth and mild the extensive Morphy Richards detergent then wipe with a dry range cloth www morphyrichards com For details of other Morphy Richards products please see our website www morphurichards com RN40630 MUK Rev2_Instruction Book 15 09 2010 15 569Page 8 E REGISTERING YOUR TWO YEAR GUARANTEE Your standard one year guarantee is extended for an additional 12 months when you register the product within 28 days of purchase with Morphy Richards If you do not register the product with Morphy Richards within 28 days your product is guaranteed for 1 year To validate your 2 year guarantee register with us online at www morphyrichards co uk N B Each qualifying product needs to be registered with Morphy
10. guarantee e This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer For electrical products sold within the European Community At the end of the electrical products useful life it should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice in your country morphy richards The After Sales Division Morphy Richards Ltd Mexborough South Yorkshire England S64 8AJ Helpline office hours UK 0844 871 0960 Spare Parts 0844 873 0726 Republic of Ireland 1800 409 119 RN40630 MUK Rev2 08 10 rphutichards com
11. ired setting e Your Morphy Richards iron is fitted with a temperature indicator light which will switch on and off whilst you are ironing This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen e It is always a good idea to begin with cool fabrics and work up to higher settings An iron heats up quicker than it cools down so you will save time and energy E FEATURES OF YOUR IRON E Dry ironing You can use your iron as a dry iron only Make sure the variable steam control is set to the symbol Any temperature setting may be used depending on the garment The spray feature may be used provided there is water in the tank see Filling section You do not need to put any water in the tank when dry ironing only RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 age 6 E Water Spray D Press the water spray button and aim the spray of water at stubborn creases You can do this whilst dry ironing providing there is water in the tank When using the water spray it may be necessary to push the button a few times to get the spray pump primed E Variable steam B Fill the iron with water as described in Filling page 5 and insert the plug into the electrical socket The steam output can be varied from low to
12. ly qualified person s in order to avoid a hazard e Do not operate the iron with a damaged cord or if the iron has been dropped or damaged and if there are visible signs of damage or if it is leaking To avoid the risk of electric shock do not disassemble the iron but telephone Morphy Richards for advice Incorrect reassembly can cause a risk of electric shock when the iron is used E Special instructions If your iron does not work check the following points e Has the temperature control been set to the required temperature Is the plug in its socket Is the plug itself or the socket faulty Check by plugging in another appliance e WARNING When not in use your iron should never be placed flat and left on an ironing board e To prevent damage to the textile being ironed follow the temperature guide carefully Test the inside of the hem of the garment When ironing is complete remove the plug from the socket empty any remaining water from the tank and allow to cool before storage If you drop or severely knock your iron this could cause internal damage even if the outside appears alright Have it checked by a qualified electrician It is recommended that you use up one beaker of water by operating your iron s steam and shot of steam functions before ironing any clothes as some dripping may occur while your iron s steam system is activated E ELECTRICAL REQUIREMENTS Check tha
13. normal and indicates that the system is functioning correctly Auto shut off certain models only If your iron is fitted with the auto shut off function it will automatically shut down after a set period If the iron is left unattended in the horizontal position it will shut down after 1 minute If it is left in the vertical position it will shut down after 8 minutes The auto shut off light will flash indicating the product is in shut down mode and will be accompanied by an intermittent beep sound To reactivate the iron gently shake it the temperature indicator light will come on indicating the iron is warming up Wait for the iron to heat up as normal H Anti scale system certain models only The life long anti scale system reduces scale deposits and helps prolong the life of the iron Ireland Helpline 1800 409 119 RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 age 7 E MAINTENANCE IMPORTANT Do not descale the soleplate with descaling products proprietary cleaning agents or vinegar when flushing out the soleplate E EMPTYING AND STORING When you have finished ironing unplug your iron Ensure that the variable steam control is set at the O position H lift up the filler cap and empty any i To clean a ceramic remaining water out of the filling coated soleplate Alo Do not store in the box ut in an upright position so cert
14. t the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A C Alternating Current If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted WARNING A damaged or severed mains cable fitted with a plug should never be connected to the mains supply It must be destroyed as a damaged cable becomes hazardous if connected to a power socket Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted WARNING This appliance must be earthed RN40630 MUK Rev2_Instruction Book 15 09 2010 15 5 age 4 E INSTRUCTIONS FOR USE B Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code Symbol aa a el 120 C Max Cool 160 C Max Warm 210 C Max Hot Max Setting Control knob Do not iron positions at all ee eco Fabric Silk Nylon Acetates Wool Polyester Cotton Linen e g Acrilan mixtures e g Rayon Rayon Courtelle Orlon Polyester Cotton mixtures Triacetates e g e g Rayon Linen Tricel Polyester Ironing Iron on wrong side Fabrics requiring this if moisture required use damp cloth setting usually require steam pressing for heavy Not Acetate cotton denim etc With water in tank
15. ualify for the 1 year guarantee the appliance must have been used according to the instructions supplied For example crumb trays should have been emptied regularly fi EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where The fault has been caused or is attributable to accidental use misuse negligent use or used contrary to the manufacturer s recommendations or where the fault has been caused by power surges or damage caused in transit The appliance has been used on a voltage supply other than that stamped on the products Morphy Richards products are intended for household use only Morphy Richards has a policy of continuous improvement in product quality and design The company therefore reserves the right to change the specification of its models at any time For details of other Morphy Richards products plus replacement parts and WWW MO accessories please see our website 3 Repairs have been attempted by persons other than our service staff or authorised dealer 4 The appliance has been used for hire purposes or non domestic use 5 The appliance is second hand 6 Morphy Richards are not liable to carry out any type of servicing work under the guarantee 7 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee 8 Batteries and damage from leakage are not covered by the
Download Pdf Manuals
Related Search