Monarch 9416 Printer User Manual
Contents
1. duel UNS No Monarch Manual 9416 Printer McDonald S Baer S DENNISON TC941XMCD Rev AE 8 07 2007 Paxar Americas Inc All rights reserved Each product and program carries a respective written warranty the only warranty on which the customer can rely Paxar reserves the right to make changes in the product the programs and their availability at any time and without notice Although Paxar has made every effort to provide complete and accurate information in this manual Paxar shall not be liable for any omissions or inaccuracies Any update will be incorporated in a later edition of this manual 2005 Paxar Americas Inc All rights reserved No part of this publication may be reproduced transmitted stored in a retrieval system or translated into any language in any form by any means without the prior written permission of Paxar Americas Inc WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause har2. Indicator Light Description Feed Button GREEN Printer is on and ready to use FLASHING Printer is paused Press the FEED GREEN button to resume printing FLASHING RED Printer error condition See Chapter 4 Troubleshooting for error conditions and solutions ORANGE The printer is detecting the labels No light Printer is off Make sure the power supply is connected properly See Connecting the Power Supply earlier in this chapter Getting Started 1 5 Loading Labels If you run out of labels while printing do not turn off the printer when reloading the labels You may lose your data The printer resumes printing when reloaded 1 Remove and discard the tape from a new roll of labels 2 Press the cover release levers located on both sides of the printer towards the front of the printer to release the cover 3 Lift open the cover 1 6 Equipment Manual 4 Remove a supply holder guide from one end of the supply holder The supply holder is normally attached with a line to the inside of the printer Supply Holder Guides Supply Holder 1 5 Supply Core Adapter Slide a roll of labels onto the supply holder If the core diameter on your roll of labels is 1 inch in diameter remove the 1 5 inch supply core adapters from the supply holder guides Slide the supply holder guide back onto the end of the supply holder Getting Started 1 7 7 Insert the ends of the supply
3. Width 8 3 211 mm Depth 9 4 239 mm Weight 4 1 Ibs 1 9 kg without power supply Shipping Weight 9 0 Ib 4 1 kg Power U S 120 VAC 10 60Hz International 220 VAC 10 50Hz Operating Limits Operating Thermal Direct 40 to 105 F 4 to 40 C Storage 40 to 140 F 4 to 60 C Printhead 4 09 104 mm 203 dpi 8 0 dots per mm Printing Method Thermal Direct Specifications A 1 A 2 Equipment Manual Visit www paxar com for sales service supplies information and telephone numbers for our International locations AN TOLL FREE 1 800 543 6650 In the U S A 1 800 363 7525 In Canada
4. Or click Cancel to cancel these changes and return to the previous screen Edit Overlay Key Data 6 Click Done when finished editing the label You return to the previous screen Overlay Edit 5 6 Equipment Manual 7 Click Done to return to the main screen Whenever you return to the main screen you are prompted Overlay Edit Complete x fs Connect the serial cable from the PC to the keypad terminal Click the Update button to download the updated label data to the keypad o Click OK to continue If you made changes print the new overlay see Printing the Overlay for more information update the keypad s software application see Updating the Keypad for more information Using the Update Utility 5 7 Defining Custom Colors 1 From the main screen click Edit Overlay The Overlay Edit screen appears Click the key to change The Edit Overlay Key Data screen appears Click Change Color The Color screen appears From the Color screen click Define Custom Colors The Custom Color screen appears Hue 120 Red Sat 240 Green i2 loi iba Lum o Blye 12 OK ul Cancel Add to Custom Colors Enter values for Hue Sat Lum Red Green and Blue as necessary The color changes based on each value you change Click Add to Custom Colors Click the color you just added to the custom colors palette Color A 7 BI 3900000 Ba IN Bu 000000 BU
5. 2171111 OOO 000 000 0o00 ml Custom colors OOS ENN OOOO B B Click OK when finished defining a custom color for the selected key You return to the previous screen Edit Overlay Key Data Or click Cancel to cancel these changes and return to the previous screen Edit Overlay Key Data Click Done when finished editing the label You return to the previous screen Overlay Edit 5 8 Equipment Manual 10 Click Done to return to the main screen Whenever you return to the Main screen you are prompted Overlay Edit Complete x i Connect the serial cable from the PC to the keypad terminal Click the Update button to download the updated label data to the keypad 11 Click OK to continue 12 If you made changes print the new overlay see Printing the Overlay for more information update the keypad s software application see Updating the Keypad for more information Deleting a Key You can delete a key from either the Edit Overlay Key Data or Edit Label Data screen When you delete a key the key s information is removed from the database e the key appears as a black box on the overlay Note Check with your System Administrator before removing any key from the database 1 From the main screen click Edit Overlay The Overlay Edit screen appears Using the Update Utility 5 9 2 Click the key to delete The Edit Overlay Key Data screen appears When
6. holder into the slots in the supply roll mount Supply Roll Mount Note The plastic line attaching the supply holder to the printer should be tucked down out of the way of the supply holder and supply holder guides Otherwise the plastic line may wrap around the supply holder or get caught on the supply holder guides 1 8 Equipment Manual 8 Turn the dial to adjust the supply guides to their widest position Supply Guides 9 Feed the labels printing side up under the supply guides and over the platen roller Supply Guides Getting Started 1 9 10 11 12 13 14 Press the labels under the supply guides Turn the dial to adjust the supply guides so that they barely touch the edges of the label backing paper Close the cover until it locks in place Press the FEED button The indicator light should be GREEN Calibrate the supply if printing stops and the indicator light turns RED or the labels do not properly advance See Calibrating the Supply for more information 1 10 Equipment Manual Calibrating the Supply 1 2 Turn off the printer Press and hold the FEED button while turning on the printer Release the FEED button after the indicator light starts flashing ORANGE The printer calibrates the die cut sensor measures the label length and prints the test labels To resume normal printing turn off the printer wait two seconds then turn it back on again
7. you click Delete Key you see Warning Clicking OK will delete all data for this key from the database Clicking Cancel aborts this operation d Cancel 3 Click OK to remove ALL data for this key from the database and display a black box in place of this key on the overlay 4 Click Cancel to return to the previous screen and keep the key in the database 5 Click Done to return to the previous screen 6 Click Done to return to the main screen Whenever you return to the main screen you are prompted on 1 Connect the serial cable from the PC to the keypad terminal Click the Update button to download the updated label data to the keypad Click OK to continue If you made changes print the new overlay see Printing the Overlay for more information update the keypad s software application see Updating the Keypad for more information 5 10 Equipment Manual Printing the Overlay If you make any changes to the overlay print it and insert it into the keypad 1 From the main screen click Edit Overlay The Overlay Edit screen appears Click Print The Print screen appears Your Print screen may appear differently based on your operating system and printer Print 12 x General Layout Paper Quality Select Printer Re A TEGIN u xerox on ENG SERVER 39 QMS PS 1700 v52 4 K xante on ENG SERVER _ n Status Ready Location Find Printer Comment r Page Rang
8. 2 Press the number 1 button The display shows the current date setting If this is correct press the McDonald s button to return to the main display To change the setting use the numeric buttons Press 1 to change the month Press 2 to change the day Press 3 to add a year Press 4 to subtract a year w oe gt gt Press the McDonald s button to save the changes and to return to the main display Using the Keypad 2 5 To set the time 1 Press the McDonald s button three times SELECT DATE OR TIME 2 Press the number 2 button The display shows the current time setting If this is correct press the McDonald s button to return to the main display To change the setting use the numeric buttons press 1 to change the hours press 2 to change the minutes press 3 to change AM PM 3 Press the McDonald s button to save the changes and to return to the main display 2 6 Equipment Manual Processing the Product Use the McDonald s application to label any product for freshness All products are listed on the buttons on the keypad The numeric buttons on the keypad allow you to enter the quantity of labels to be printed To print one label at a time 1 Press any product button once CHECKING PRINTER STATUS PLEASE WAIT 2 Alabel prints for the product you selected To print multiple labels 1 Press the numeric buttons to enter a quantity QTY X SELECT PRODUCT
9. 28800 C Even Space None C 480 38400 9600 57600 Word Length Stop Bits Seven One 14400 115200 G Eight C Two r Flow Control 31 r Com Pot None Comi O RTS TENES Xon Xoff RTS XonZolf Cancel The default settings match the settings of the keypad 3 Make any changes and click OK when finished You return to the main screen Using the Update Utility 5 13 To update the keypad terminal 1 Connect the serial cable from the computer to the keypad terminal 4 McDonalds Update Utility Oo x Edit Overlay Update Terminal Exi 2 From the main screen click Update Terminal BEER The Update Utility begins sending the application and data files to the keypad This process may take several minutes Do not click Cancel while updating the keypad terminal 3 When finished you see Update Complete Please unplug terminal power and connect printer cable Click OK 5 14 Equipment Manual Unplug the keypad s serial cable to the computer and reconnect it to the printer Unplug the terminal s power cable Wait several seconds and then reconnect the power cable to the keypad The keypad is now ready to use Click Exit to close the Update Utility Using the Update Utility 5 15 5 16 Equipment Manual SPECIFICATIONS A This appendix includes information about printer specifications Printer Specifications Height 6 6 168 mm
10. If the supply does not calibrate make sure the die cut sensor has not been accidentally moved Checking the Die Cut Sensor After loading supplies make sure you did not accidentally move the die cut sensor The die cut sensor senses and calibrates the supply For your supplies make sure the die cut sensor is in the detented position and the middle of the square lens lines up with the arrow inside the printer Sensor set for die cut supplies Getting Started 1 11 1 12 Equipment Manual USING THE KEYPAD 2 This chapter describes how to connect the keypad use the keypad configure the McDonald s system IMPORTANT set the date and time process the product print a Use First label use the Stop Printing function Note Keep this manual in a safe place otherwise changing the settings requires a service call 9 9 9 9 9 9 Connecting the Keypad s Power Supply The keypad should not be operated in a location that has room temperatures above 158 F or below 4 F for extended periods of time This could permanently damage the display To connect the power supply to the keypad 1 Place the keypad on a table or shelf 2 Place the keypad s power supply in a suitable location preferably on a table near an electrical outlet 3 Plug the three hole end of the AC adapter cable into the three pronged outlet in the keypad s power supply 4 Plug the power supply cable with the L shaped end into the socket on t
11. UAL TEA TOPPING MUSTARD LETTUCE TORTILLAS TOMATO MK VEGETABLE OPEN BOTTLE BREWED BOTTLE OPEN OPEN 2 3 4 5 6 7 8 9 0 mem 2 To change a key s text click the key to change The Edit Overlay Key Data screen appears BBEdit Overlay Key Data x Example of BLOCK Overlay Key CHEESE Mam here and enter new key Edit Label Change Delete Key data olor Done Cancel 3 Click in the box and enter the new key data Using the Update Utility 5 3 4 Click Edit Label to change the label s wording offset time and choose to print the time on the label The Edit Label Data screen appears BS Edit Label Data x Enter English Text Line 1 AMERICAN Enter English Text Line 2 CHEESE Enter Spanish Text Line 1 QUESO Enter Spanish Text Line 2 AMERICANO Enter Offset Time 24 Hrs C Min M Print Time on Label Example AMERICAN Current QUESO time amp date cot Laepd 4 46 PM pae Key 414 2005 4 13 2005 5 Change any necessary text for the label or offset time 6 Decide if you want to print the time on the label If so make sure the box is checked next to Print Time on Label If not make sure the box is not checked next to Print Time on Label A sample label displays while you make changes 7 Click Done when finished editing the label You return to the previous screen Edit Overlay Key Data Or click Cancel to cancel
12. X represents the quantity you entered 2 Press a product button CHECKING PRINTER STATUS PLEASE WAIT The labels print for the product you selected Using the Keypad 2 7 Printing a Use First Label Apply a Use First label to any product on the shelf that needs to be used first 1 Press the Use First button on the keypad bottom right CHECKING PRINTER STATUS PLEASE WAIT 2 Alabel with the words Use First prints Using the Stop Printing Function If you press the wrong number of labels to be printed or the wrong product button 1 Press the Stop Printing button on the keypad upper right to cancel printing 2 Press the FEED button on the printer to clear the stopped label Note You must be at the main display for this function to work Future Upgrades Updates will be provided by Supervisors To use the Update Utility see Chapter 5 Using the Update Utility for more information 2 8 Equipment Manual CARE AND MAINTENANCE EJ This chapter tells you how to clear label jams clean the printhead Clearing Label Jams When you are printing and a jam occurs the indicator light turns RED To clear the jam 1 Turn off the printer Press the power switch on the back of the printer to the off position O 2 Press the cover release levers towards the front of the printer to release the cover Lift open the cover If necessary remove any previously loaded labe
13. application Using This Manual Following is a summary of the contents of this manual Chapter Contents 1 Getting Started Unpacking and installing the printer and loading supplies 2 Using the Keypad Configuring the system setting the date and time and processing products 3 Care amp Clearing label jams and cleaning Maintenance the printer 4 Troubleshooting Common problems and their solutions 5 Using the Update Editing the keypad overlay and Utility updating the keypad settings A Specifications Printer specifications Getting Started 1 1 Audience This Equipment Manual is for the person who prints and applies labels This chapter includes information about unpacking the freshness system connecting the printer s power supply reading the printer s indicator light loading labels Information in this document supercedes information in previous versions Check our Web site www paxar com for the latest documentation and release information Unpacking the Freshness System After you unpack the system you should have the following 9416 printer and power supply power strip communications cable keypad and AC adapter depends on kit ordered For missing items service technical assistance or ordering labels please call the number on the back of this manual Keep all packaging material in case you need to move or return the system 1 2 Equipment Ma
14. e G All Number of copies NS Selection Current Page O Page ppc sg Cancel Select the printer Make any changes to the number of copies layout and paper quality if necessary Click Print to send the overlay to the selected printer Click Done to return to the main screen Using the Update Utility 5 11 Whenever you return to the main screen you are prompted Overlay Edit Complete x A Connect the serial cable from the PC to the keypad terminal Click the Update button to download the updated label data to the keypad 7 Click OK to continue Updating the Keypad After the changes are made to the key and label data send the updated data to the keypad terminal so the changes appear on any future labels printed Note Make sure the printer is connected to the computer Make sure the computer s serial communication values match those at the keypad See Communication Settings for more information 5 12 Equipment Manual Communication Settings The Update Utility scans your computer for available communication ports and adds them to the Com Port list box To display the communication settings 1 From the main screen click Setup Com Port You see m 2 Enter the password 5675 and click OK The Communications Settings screen appears H Communications Settings r Baud 4 r Parity C 1200 19200 Odd Mark c C 2400 O
15. he right side of the keypad Using the Keypad 2 1 Y C L0 a L shaped Connector 5 Plug the three pronged end of the AC adapter cord into a grounded electrical outlet Q o 2 2 Equipment Manual Connecting the Communication Cable To connect the serial cable from the printer to the keypad 1 Turn off the printer and the keypad before connecting the cable 2 Connect the serial cable to the 9 pin serial port on the back of the printer p C NER s 9 pin Serial Port Using the Keypad 2 3 3 Connect the other end of the serial cable 9 pin to the serial port on the right hand side of the keypad Serial Port About the Keypad Use the McDonald s application to label inventory products The buttons are color coded so you can easily print the item labels Yellow breakfast items Red grill area items Blue front counter items Green prep salad items Orange miscellaneous items 2 4 Equipment Manual Setting up the McDonald s System IMPORTANT Please perform the following steps before using the system To set up the system 1 Press the McDonald s button three times SELECT DATE OR TIME 2 Press the number 3 button SENDING PACKET COMMAND TO PRINTER PLEASE WAIT 3 Press any key to print a label Setting the Date and Time To set the date 1 Press the McDonald s button three times SELECT DATE OR TIME
16. htly dampen a cloth with water and wipe the printer s exterior surfaces clean Use a dry soft bristled brush to clean paper dust out of the printer s interior s Platen Roller 3 2 Equipment Manual TROUBLESHOOTING 4 This section lists some common problems and their solutions Problem Action Indicator light is off Check the power connections when the printer is from the power supply to the turned on printer and wall outlet See Connecting the Printer s Power Supply in Chapter 1 for more information Indicator light is Check the cable connections GREEN but the from the keypad to the printer printer will not print See Connecting the Communication Cable in Chapter 2 for more information Make sure the labels are loaded correctly and that they are the Paxar Monarch labels recommended for this application See Loading Labels in Chapter 1 for more information Clean the printhead See Cleaning the Printhead in Chapter 3 for more information Make sure the cover is closed Indicator light is RED Out of labels or the cover is open Load labels See Loading Labels in Chapter 1 for more information Make sure the cover is closed until it latches then press the FEED button Troubleshooting 4 1 Problem Printing stops and indicator light turns RED Or the printer does not advance from one label to the next correctly 4 2 Equipment Manual Action Calibrate the sup
17. ls Lift up the supply holder and remove one of the supply holder guides 5 Slide the labels off the supply holder 6 Remove the jammed labels Caution Do not use sharp or pointed objects to remove labels or damage to the printhead may occur 7 Reload the labels See Loading Labels in Chapter 1 for more information Close the cover until it locks in place Press the FEED button The indicator light should be GREEN Care and Maintenance 3 1 Cleaning the Printhead Remember to clean the printhead every time you load a new label roll into the printer Caution You must turn off the printer s power before cleaning the printhead To clean the printhead while printing you may lose your data when you turn off the printer 1 Turn off the printer Press the power switch on the back of the printer to the OFF O position 2 Press the cover release levers towards the front of the printer to release the cover Lift open the cover Moisten a cotton swab with isopropyl alcohol 5 Rub the cotton swab across the printhead to remove any build up 6 Allow the printhead to dry for one minute before you close the cover and resume printing Cleaning the Platen Roller and Printer Moisten a cotton swab with isopropyl alcohol and run NS S the cotton swab across the platen roller Turn the platen roller with your finger and make sure it is clean all the way around Note Do not remove the platen roller Slig
18. mful interference in which case the user will be required to correct the interference at his own expense CANADIAN D O C WARNING This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le R glement sur le brouillage radio lectrique dicte par le minist re des Communications du Canada Trademarks MONARCH and 94166 are registered trademarks of Paxar Americas Inc Paxar is a trademark of Paxar Corporation McDonald s is a registered trademark of McDonald s Corporation Microsoft Windows NT and Office are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Other products are trademarks or registered trademarks of their respective companies and are hereby acknowledged Paxar Americas Inc 170 Monarch Lane Miamisburg Ohio 45342 TABLE OF CONTENTS GETTING STARTED 1 1 Using This Manual 3 ntum eroe Portes 1 1 Audience eec 1 2 Unpacking the Freshness System seeessss 1 2 Connecting the Printer s Power Supply c eee 1 3 Reading the Indicator Light 1 5 Loading Panels i i seti aee tet idiot tied sata idee Da ab Arif 1 6 Calibra
19. nual Connecting the Printer s Power Supply Do not touch the electrical connectors while setting up the printer Electrostatic discharge can damage or destroy the printhead or electronic components To connect the power supply to the printer 1 Place the printer on a table in a location that allows easy access to the front of the printer Note Never operate the printer resting on its side or upside down 2 Turn off the printer Press the power switch on the back of the printer to the off O position 3 Place the power supply in a suitable location preferably on a table near an electrical outlet 4 Plug the three hole end of the AC adapter cable into the three pronged outlet in the printer s power supply Caution The printer s power supply uses a different voltage than the keypad To connect the wrong power supply could permanently damage the keypad or the printer Straight Plug Plug is the power supply is the power supply for the printer for the keypad Getting Started 1 3 5 Plug the round end of the power supply cable into the socket at the back of the printer 6 Plug the three pronged end of the AC adapter cord into a grounded electrical outlet Warning The printer and power supply should never be operated in a location where either one can get wet Personal injury could result 1 4 Equipment Manual Reading the Indicator Light The indicator light monitors the printer s status gu N
20. ply 1 Turn off the printer 2 Load labels See Loading Labels in Chapter 1 for more information 3 Press and hold the FEED button while turning on the printer 4 Release the FEED button after the indicator light starts flashing ORANGE The printer calibrates the die cut sensor measures the label length and prints the test labels 5 To resume normal printing turn off the printer wait two seconds then turn it back on Load different labels See Loading Labels in Chapter 1 for more information Clear a label jam See Clearing Label Jams in Chapter 3 for more information Make sure the die cut sensor is in the correct position was not accidentally moved while loading supplies See Checking the Die Cut Sensor in Chapter 1 for more information Problem Label exits partially out of the printer or skips a label Action A label may be caught in the printer See Clearing Label Jams in Chapter 3 for more information Make sure the labels are loaded correctly and that they are the Paxar Monarch labels recommended for this application See Loading Labels in Chapter 1 for more information Printing is faded or poor quality Make sure the labels are loaded correctly and that they are the Paxar Monarch labels recommended for this application See Loading Labels in Chapter 1 for more information Make sure the cover is closed completely Clean the
21. printhead See Cleaning the Printhead in Chapter 3 for more information Adjust the print speed darkness See your System Administrator Troubleshooting 4 3 Problem Test label does not print Action Make sure the supply is loaded correctly Make sure the die cut sensor is in the correct position was not accidentally moved while loading supplies See Checking the Die Cut Sensor in Chapter 1 for more information The keypad displays an error 4 4 Equipment Manual To clear an error displayed on the keypad turn off the printer s power switch wait two seconds then turn on the printer USING THE UPDATE UTILITY 5 The McDonald s Update Utility allows you to edit the keypad s overlay change a key s description print the new overlay send the updated data to the keypad Note The Update Utility is only for Supervisors or System Administrators Using the Update Utility 5 1 Before You Begin Install the Update Utility on a computer with Microsoft Windows 98 or greater The computer should also have Microsoft Office 2000 or greater installed which includes Access database software 1 3 Install the Update Utility by inserting the Update Utility CD into the CD ROM drive on your computer Follow the instructions on the screen to complete the installation Start the Update Utility The main screen appears x McDonalds Update Utility CI
22. these changes and return to the previous screen Edit Overlay Key Data 8 Click Done when finished editing the label You return to the previous screen Overlay Edit 9 Click Done to return to the main screen 5 4 Equipment Manual Whenever you return to the main screen you are prompted Overlay Edit Complete x A Connect the serial cable from the PC to the keypad terminal Click the Update button to download the updated label data to the keypad 10 Click OK to continue 11 If you made changes print the new overlay see Printing the Overlay for more information update the keypad s software application see Updating the Keypad for more information Using the Update Utility 5 5 Changing a Key s Color 1 From the main screen click Edit Overlay The Overlay Edit screen appears 2 Click the key to change The Edit Overlay Key Data screen appears 3 Click Change Color The Color screen appears Basic colors LILIDIEJEJEJEJDJ OOOOOOOC LILILIEIEIEIEIEI LIE IEIEIEIEILILI re TS mil mI rrt Custom colors 000A IS E UN m E m m m SS Define Custom Colors gt gt Carel 4 Pick the color you want for the selected key If you want to define a custom color click Define Custom Colors gt gt See Defining Custom Colors for more information 5 Click OK when finished picking a color for the selected key You return to the previous screen Edit Overlay Key Data
23. ting the Supply ssec teo oet dt dido be Pa obe PaRe pont ss 1 11 Checking the Die Cut Sensor cscs 1 11 USING THE KEYPAD 2 1 Connecting the Keypad s Power Supply sssss 2 1 Connecting the Communication Cable ssssss 2 3 About the Keypad arieciooieitine deo Mp pe icit Beo e esmeeg cade 2 4 Setting up the McDonald s System 2 5 Setting the Date and Time cecce 2 5 Processing the Product 5 eura pao Rates ares 2 7 Printing a Use First Label i idee Enn 2 8 Using the Stop Printing Function was cisecossioetavstberteetoresesens 2 8 Future pgradgs o od o etat tace ca s 2 8 CARE AND MAINTENANCE 3 1 Clearing Label Jams zn roo ro eter Sere 3 1 Cleaning the Printliead cer ets 3 2 Cleaning the Platen Roller and Printer 3 2 TROUBLESHOOTING 4 1 USING THE UPDATE UTILITY 5 1 Before You Beginl iui ase beni i e va 5 2 Editing the OVelrlady vuesdatdetdbe pute pares Deka ns toxc ovest ims 5 3 Changing a Key s Calor usen dece eeu eee fs 5 6 Defining Custom Colors cic o po rte tien 5 8 Deleting q Key nra onoi eek odnisiti pokore ition 5 9 Printing the Overlay cere Ene 5 11 Updating the Keypad ceee 5 12 Communication Setrigs 225i eod f ae eens 5 13 SPECIFICATIONS A 1 Printer Specifications sssssssm A 1 GETTING STARTED EN Use this system for product freshness The system consists of a Monarch 94166 printer and a keypad with the McDonald s Freshness
24. x Edit Overlay Status Bar At the bottom left hand corner there is a status bar which displays the utility s current status Decide what you want to do next To edit the overlay change a key s color or description see Editing the Overlay for more information To update the keypad s software application see Updating the Keypad for more information 5 2 Equipment Manual Editing the Overlay You can change the way the overlay appears a key s color or text description 1 From the main screen click Edit Overlay The Overlay Edit screen appears CINNAMON LiquiD Bu BACON at suivereD BLOCK LEAF SALAD ASIAK AVERY STOP BAGELS MELT MARGARINE TEA STRIPS SAUCE onions CHEESE LETTUCE PREPARED VEGETABLE DENNISON PRINTING GALLON OPEN OPEN lux BACON ENGLISH McGRIDDLE BUNS E BLOCK MANDARM sucED Bs BAK SAUCE MUFF CAKES FROZEN MAYO CHEESE cHEESE ORANGES LEMOHS RErERI FROZEN DECANTER OPEN TABLE RATED BURRITO ICED ORANGE TARTAR CHEDDAR parm SLICED RTE ROLLED HOTCAKES FOLDED COFEE cooues Glaze sauce sack CHEESE LIMES EXPIRES EGGS SYRUP BOTTLE OPEN OPEN BURRITO ORANGE BULK FLummY SHAKE DEHYDRAT RANCH TOMATOES MX JUICE CREAMER TOPPING syRUP ED SAUCE OPEN PARFAIT PIE YOGIRT FROZEN ONIONS BOTTLE CANADIAN LIQUID BULK ICE SUNDAE HONEY SHREDDED GRAPE SALAD SOUTHWEST BACON MARGARINE EQ
Download Pdf Manuals
Related Search