Mitsubishi Electronics DX
Contents
1. MITSUBISHI amp ELECTRIC SECURITY PRODUCTS DX TL910U Digital Video Recorder oimple Set Up Guide Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved DX TL910U Quick Reference Guide This Quick Reference Guide is designed to help you get quickly acquainted with your Mitsubishi DX TL910U Digital Video Recorder DVR This guide will also help you HOW TO program and perform commonly used functions For additional information please reference the DX TL910U Installation and Operations Manual S 30 n Features Easy to Use Duplex Operation Per Camera Settings 60PPS 5 Quality Grades Covert Camera Copy to CFC or VHS Password Protection Network Support via DX PC25 or Web Browser Front View 1 Power 2 Access Indicator 3 Camera Sequence 4 Timer Button 5 REC STOP 6 Shuttle Ring 7 Jog Dial 8 Split Sequence 9 Zoom 10 Pre Alarm Indicator 13 Lock 16 Compact Flash Slot 19 Warning Reset 11 M Detect Indicator 14 Lock Button 17 Copy Button 20 SETUP 22 Stop Pause Rev Play amp Play 12 Emergency Ind 15 Video Audio out 18 Alarm Interrupt 21 Search 17 18 19 20 21 22 23 24 Figure 2 Rear View 1 Main Power Switch 2 Video Out 3 Camera In o 4 A 4 Camera Out 7 Ground 10 Alarm In 13 Network Connector 5 A C Power Socket 8 MIC In 11 I O Terminals 6 Audio In Out 9 Reset 12 RS 232C Jog Shuttle Usage2. The Jog Shuttle is used for two types of operations 1 Playback Features When Playing back turning the Shuttle outside E Se s YA Ww 45 ring Clock Wise Forward or Counter Clock Wise Reverse will change the playback speed When in Pause mode the Shuttle is also Figure 3 used to set the desired playback speed From Pause turn the Shuttle to the desired Playback speed and press Pause to hold the speed Press Play to exit 2 Programming of DVR The Jog and Shuttle are used to navigate select change and exit the various On Screen menu and sub menu s IMPORTANT INFORMTION e The Jog inside ring when turned CW or CCW is used to move the OSD cursor CC CAN Up Down Across selecting various functions The Jog is also used to make a change within the selected field blinking in RED e The Shuttle outside ring is used to select accept and exit the various functions When a change is accepted the field turns from blinking RED to WHITE background a Turning the Shuttle CW selects the function field goes from White background to blinking in RED To accept the change turn the Shuttle CW and the field goes from blinking RED back to White JOG dial d SHUTTLE ring d ez e c Turn the Shuttle CCW to EXIT and go back through the various menu layers Power Up This is a two step process first press the Main Power Switch ON rear panel just above the Power cord and from the front of the unit press the Power Button fro
3. select and make needed changes To Exit the SETUP Menu after the change has been made field not blinking in RED and use the SHUTTLE CCW to exit the various Sub Menus until the live screen is displayed or simply press the SETUP button to exit SETTINGS TIME DATE DISPLAY SETTINGS HES DISPLAY SETTINGS MOTION DETECTION SETTINGS RECORD SETTINGS TIMER PROGRAM SETTINGS INITIAL SET UP INFOPHATION QUICK SETTINGS MEMO Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved 3 How to SECTION RECORD MONITOR VIEWING PLAYBACK SEARCH COPY ALARM SETTING MOTION SETTING RECORDING amp ALARM REC SETTINGS TIMER REC INITIAL SETUP INFORMTION HDD REPEAT NETWORK SETTINGS ESTABLESHING A NETWORK CONNECTION EU e pg em eo os A Recording 1 Once the DVR is installed with all of the cameras connected and the various settings in the DVR are set Time and Date how each camera is to record and other important menu settings a How to Activate RECORD Simply press the REC STOP figure 1 item 5 button and when the button illuminated in RED the DVR is recording e To test recording simply turn the SHUTTLE CW the monitor screen will black out and go back to live display At this time press the REV PLAY button and the DVR will playback the latest recording in reverse To stop playback just press the STOP button see figure 2 20 e If any kind of a WARNING appears on the screen call you
4. 1 Go Links Ka p 4 gt gt mywebsearch Search Screensavers D Smiley Central E Cursor Mania eo My Info v Games ZS Customize e My Button 1 Favorites x Thad Ice gt Authentication Links Boat and Yacht Boats yachts an amp amp EGlobalv achts c 1959 40 Feet Ch 1976 27 ft Catali If You don t want to log in click here to exit log out Fiberglass Repai Log in or log in as a different user Note ID and password are case sensitive userID password login Change Your Password Note ID and password are case sensitive userID password new password retype new password change clear S amp amp Done Es E intent 2 Astart 21 e E O Ginbox ety pocu MJox t amp 1n30 Sunt Requesti amp 3128 Links GLIA PA 2 04 em MH elcome 3 Select LIVE PLAYBACK or LOGOUT to EXIT up to 10 users can connect at once DX TL9I0U Web Page 4 n Playback to perform Time Date Search select single screen mode first The SEARCH buttons will appear bogged amp az ront log out change L H ust Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved 8 DX PC25U Application Software This software comes with each DVR in a CD form Load the software to as many PC s that will need access to the DVR Up to 5 u
5. E e NOTE Overwrite will erase anything previously saved on your flashcard NO OVERWRITE will record in the available space after your last recorded event 4 Select using the SHUTTLE ring and use the JOG to make a change as needed Use the Shuttle CCW to exit this selection Use the JOG dial and go to TRANSFER PERIOD COPY MENU The following options appear START END E EIE START LATEST DATA for example if you DIRECT ION MAIN HDD4CFC DIRECTION CFCAMAIN HOD MODE UERURI TE MOE VERY ITE select START you only have to imput the start TRANSFER PERIOD START END TRANSFER PERIOD START END time of the needed video no end time is needed END 01 01 2004 Q0 10 END 01 01 2004 00 00 10 This function will copy from given time and fill EXECUTE EXECUTE the CFC with maximum data 6 Input the required period setting 7 Usethe JOG SHUTTLE ring to move accept your entries and use the SHUTTLE CCW to EXIT the Date settings 8 Usethe JOG dial to move to EXECUTE and the SHUTTLE ring to activate the execution 9 When complete turn the SHUTTLE ring counterclockwise to return to the normal display mode 10 Select EXECUTE and turn the SHUTTLE ring clockwise 11 The monitor screen will indicate with a Yo number of copy process When complete the screen will indicate COMPLETE 12 Press the COPY button to remove the COPY menu from the monitor screen Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserve
6. ETUP Select YES with the SHUTTLE and with the JOG move down to SHUTTLE gt EXECUTE EXECUTE l In CAMERA CHECK when all the active cameras are displayed on the screen select EXECUTE 2 In AUTO RECORD SETTING select the RECORD CYCLE XXX Hours and EXECUTE The RECORD SETTINGS screen will appear Figure B 2a The RECORD settings for Regular PPS and GRADE and Alarm A PPS and A GRADE can be changed Press POWER button to exit 3 INITIALIZATION Move the JOG to INITIALIZATION Figure B 2b and the unit will record the new settings and go to Live Mode At this point additional features can be set via the SETUP Menu see next page bea reen dd EN M zu REI I CE iH HES EXECUTE Ho CHECK Camera COMMEQTION OND IMAGE BEFORE EXECUTE JO SELECT SHUTTLE EXECUTE SHUTTLE xt ExECUTE Figure B 2 PERFORM AUTO SET UP SHUTTLE EXECUTE Figure B RECORD SETTING GRADE a PPS GRADE SUPER ISP SUPER SUPER SUPER lt ESTD REC LBLLIHCEH PRESS POWER BUTTON TO EXIT Figure B 2a Figure B 1 INITIGOLIZATION HDD SETTING POWER OFF INITIALIZATION ALL DATA WILL BE ERASED WHEN PROCEED INITIALIZATION Figure B 2b 2 SETUP MENU Pressing the SETUP button found inside the DVR s front door will access and display the SETTINGS Menu This Menu and its Sub Menus will allow you to program other features of the DVR Again simply press the SETUP button and use the JOG SHUTTLE to move
7. d B F Alarm Settings 1 From the Main Menu select RECORD SETTING and select ALARM SETTING 2 Goto TRIGGER and select the type being used ZALARM SETTING EXT External input at rear terminal is needed to activate an alarm MD amp EXT Motion amp External input are needed to triggers an Alarm MD EXT Either Motion or External input will triggers an Alarm MD Alarm REC is initiated when Motion is detected by active input Each ALARM can support multiple camera recording simply select the needed cameras in the RECORD CAMERA line Go back to the RECORD SETTING Menu Shuttle CCW and select the Kee SE ALARM RECORD DURATION time Turn the Shuttle CCW to exit to Main Menu VE mh G Motion Detection Setting 1 From the Main menu select Motion Detection Hn SSELECTION CAMERA NUMBER 2 Select camera s that will be using MOTION 1 e errori rr SEMSITIUITtT HIGH L W to16 HOTIOM THRESHOLD 5 TEST MODE 3 Set Detection Mask pixels use the front panel buttons 1 4 to move around the mask amp use button 8 to activate and 9 to deactivate Use Split Sequence button to activate all pixels or use Zoom cys tt ap button to de activate all pixels 4 Select Sensitivity Level with the Shuttle and change with the Jog Set Motion Threshold from 1 to 192 lowest number 1 being most sensitive 6 Select Test Mode and test above settings test masked area with expected movement If change is needed go back to specific ar
8. ea and make change Exit to Main menu by using the Shuttle CCW Un ESI MODE Page 42 H Regular and Alarm Recording Setting 1 From the Main Menu select RECORD SETTING 2 Select ALARM or ALARM PLUS this unit supports ALARM where only the active ALARM channel records or ALARM PLUS where the ALARM channel plus all other channels Regular and Alarm also record 3 Two types of Recording is supported RECORD PPPS amp GRADE and ALARM REC A PPS amp A GRADE Using the Jog Shuttle move and select RECORD SETTING Use the Shuttle and Jog to move to PPS field Use the Shuttle to select red blinking and Jog to change the number of PPS for each camera input Use the same process to select the REC Grade Higher is best Longer is minimum for both sections regular and alarm recording and for each camera connected For cameras 10 to 16 Jog down and select NEXT PAGE and make changes When this second page is displayed at the bottom of the screen ESTD REC XXD XXH XXM represents how long the unit will record 24H a day with the given camera inputs PPS and Quality settings e When Timer recording is used the above information is entered in Timer Program Setting REC MODE A D e When done with step 3 test the RECORD settings to ensure they are acceptable Remember Higher PPS and Grade means less time available to REC on HD space e To test exit all menu settings press SETUP Press REC button front view 6 button light turns
9. h Record Mode has ALARM and RECORD SETTING like in step E plus other settings For additional information on other supported functions like SKIP OVER and more see the DVR User Manual 3 The last setting is for MD Motion Detection if motion recording is being used in this set time set to ON if not set to OFF J Initial Setup Information 1 From the Main Menu Jog and Select INITIAL SETUP INFORMATION GED METTUS MATH 2 Select HDD SETTINGS and set the HDD Repeat REC Main to ON if repeat FED ERRAT Mer MUD recording is needed Repeat Record will write over existing data AE Inn uhu 3 HDD REP REC SUB is used for ALARM RECORD only and set as above if set to OFF when the SUB partition 1s full no more Alarms will be recorded When set to ON Alarms are replaced FIFO K Network Connection if used get IP SUBNET amp GATEWAY ADDRESS from network department From the Main Menu Jog and Select INITIAL SETUP INFORMATION From the SUB MENU 1 Jog and Select COMMUNICATION PORT SETTING Jog and Select ETHERNET Again with the Shuttle Select and with the Jog enter the IP ADDRESS With the Jog Shuttle enter SUB NET MASK amp GATEWAY ADDRESS use the Shuttle to accept Use the Jog and Shuttle to go to ALARM NOTIFICATION SETTING and enter the IP ADDRESS to be notified when a WARNING ALARM SENSE REC MODE when set to ON Once all information 1s entered fields not blinking press SETUP Button to accept all entries The unit
10. he faster the review speed Pressing PAUSE while in FF will lock the current display speed Press STOP and then PLAY to get back to normal playback speed SEARCH D Search Function 1 Date and Time Playback Press A the SEARCH button figure 2 23 E MAINMENU SUB MENU 1 default setting SE AE EE GEET e Make sure the cursor is next to the EE EC BOSE CMELEETIDM CAREER RUPEE ELE SEARCH DATE line and turn the EXECUTE FORWARD SEARCH PLAYBACK DEVICE M IN SHUTTLE ring clockwise twice Ha IN RAMUS MAIN START END PUSH SEARCH KEY FOR X SEARCH SELECTION Copyright 2004 Mitsubishi Dua cievu unnes Arrierica WIG AU Rights reserveu 4 E The display will turn red and flash This indicates the data may be edited The format is YEAR MONTH DAY HOUR MINUTES SECONDS 2 Turn the JOG dial to select MONTH and turn the SHUTTLE ring clockwise The background of the setting item changes to red and flashes With the JOG change to needed month and accept the change by turning the SHUTTLE CW 3 Turn the JOG dial to DAY you want to search by Same as above use the JOG SHUTTLE to make changes and accept the changes Repeat the above steps for HOUR MINUTE and SECOND 4 Press SEARCH button to display the SEARCH SELECTION screen 5 Check to see that the cursor is positioned at the SELECTION CAMERA NUMBER and turn the SHUTTLE ring to make a change The background of the setting item changes to red and flashes 6 Turn JOG to
11. nt 1 The unit will go through a series of power up self test for about 20 seconds Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved 2 First Time Power UP AUTO SETUP When the DVR is taken out of the box and turned on for the first time an AUTO SETUP program will guide you trough setting the DVR s Time and Date Settings and Performing AUTO SETUP Ensure all cameras being used are connected to the DVR and are turned ON After entering Time and Date PERFORM AUTO SETUP YES or NO menu will be displayed If you choose YES the DVR will guide you through CAMERA Check and AUTO RECORDING SETTINGS These values can be changed or fine tuned via the MENU settings If you select NO the DVR will perform a power up check and go to live mode Listed below is the process and monitor screen shots displayed when you select YES in the AUTO SETUP procedures 1 AUTO SETUP TIME DATE ADJUST A TIME DATE ADJUST Using the JOG SHUTTLE as described on page 1 Select DAYLIGHT DAYLIGHT SAVING OFF SAVING with the SHUTTLE turn to the right When Selected OFF will blink in RED using the donkle Gs JOG change to ON if needed To accept the change turn the SHUTTLE again to the right ON will YEAR 2004 stop blinking in RED and background for ON will be in white Turn the SHUTTLE to the left to nne 00 00 00 exit Using the same process set the Date and Time and go to EXECUTE APPLY EXECUTE JOG SELECT B PERFORM AUTO S
12. r support department B Monitor Viewing 1 To change the view on your monitor to a single camera Multiplexer buttons pres the number 1 2 3 or 4 that corresponds to the camera you want to view in full screen 1 Camera number buttons 1 to 9 2 To change back to the 4 camera view press the SPLIT SEQUENCE button EB EB EB EB EB EB EB 3 To Zoom in on an image go to the single camera view and press ZOOM an X appears on the monitor display E e M c TIR ten screen this X shows the area to be zoomed in Press the ZOOM again and the area will be expanded to 200 Press ZOOM again and image is enlarged 400 Press 3 ZOOM button ZOOM again to exit the ZOOM function 2 GPLIT SEQUENCE button e The X will allow you to narrow the field and move to the area under study when in the zoom mode Use the navigational keys under the 1 2 3 4 camera buttons to move the arrow to the field you wanted to review C Playback Basics l Press PLAY The recorded content on the hard disc drive will be replayed E STOP NEPAUSE CV PLAY PLAY B The first time PLAY 1s activated the oldest recorded data will be displayed sn a c az first after this when PLAY 1s pressed again play will begin from last viewed image in its display format one or 4 display 2 Use the STOP PAUSE REV PLAY buttons to navigate through the recorded data To fast forward when in PLAY mode turn the SHUTTLE ring clockwise the further clock wise the SHUTTLE 1s turned t
13. red and record for about 30 seconds To review press PLAY button and check playback quality To see a single image or specific camera press the camera number on the front panel to view full screen video Press STOP when done RECORD SETTING ALARH CH RECORD SET TIHO ALARA CH ORADE PP3 Oo DROE 1 5G3P STD STD 2DAP STD 2DAP STD Jar STD gE3P STD gB3P STD gB3P STD SAI STD 2DAP STD SHUT TEE HACK NO d d d d d H 1 mt mt B 1 B t NEXT RECORD SETTING 1 2 Paget 18 1B 44 45 RECORD SETTING 2 2 Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved 6 I Timer Record Setting if being used TIMER PROGRAM JETT INOS lt TIMER FPROORAM 1 From the Main Menu select TIMER ST yaa vena P1 SET DM EM PROGRAM SETTING Select Pattern REESE E P1 P1 3 support different schedules REC MODE C d S selected Pattern will be used by DVR as ALARA REC DURAT ION 5 B default Select SET and enter time to record For DW enter day of week to record where DAY is for every day SPL TIMER PROGRAM SETTINGS Pages 46 48 TIMER PROGRAM Pages 46 47 is days of week set by user at bottom of the screen and HOL is for Holiday which is entered in Holiday Setting Menu of the Timer Program Setting menu screen 2 Usethe Jog Shuttle to enter Time military to start and stop recording Select Mode A D to REC Camera patterns A D are setup in Timer Program Setting Main menu Eac
14. select the camera number You may choose an individual camera or select ALL Turn the SHUTTLE RING clockwise 7 Setting is confirmed when all flashing stops 8 When your settings are complete turn the SHUTTLE ring counterclockwise The display returns to the TIME DATE SEARCH screen and the cursor appears on the left of the search date 9 Turn the JOG dial and select EXECUTE and turn the SHUTTLE ring clockwise 10 When the search is executed the video of the requested date time will appear in still frame The search result will appear using the split screen when all cameras are selected 11 To view the selected image press PLAY To stop playback press the STOP button To cancel the operation at any time during the set up turn the SHUTTLE ring counterclockwise until you are back at the menu screen 12 To view playback from the flash device when in the SEARCH 2 screen select using the JOG dial PLAYBACK DEVICE Select CFC You will normally view from the HDD MAIN setting Copy Function 1 To copy the HDD or the CFC make sure you first remove the CFC cover and insert your CFC card 2 Press the COPY button right next to the Flash Card port e The screen will display DIRECTION MAIN HDD gt CFC If copying to CFC no change is MD needed if copying from CFC to HDD change CFC L gt HDD and exit Use the SHUTTLE to Select and the JOG to make the change 3 Use the JOG dial and go to MODE OVERWRITE NO OVERWRIT
15. sers can connect at one time It is recommended that one user also be the Security Administrator who will setup and provide specific level access to other users Launch the Software to establish a connection 1 When the Network box appears select the DVR and click on connect 2 USERID root lower case amp PASSWORD admin000 zeros DYA Name New York Stare 19 Los Angeles Store 10 TI Details a LLL File Edit Network Search Operation Bookmarks wiew Help ED E Media Informatica Connect Disconnect Add recorder Recorder lisk Renew inka ALM MatiFicakian Control Image Information Config Picture Size GEES k Time Search an uzo04 mep EZ 3 11 06 4M EX Search Alarm List Show List Devic eee MAIN be 4 4 xq i p bb Ee eis Liwe 1 zT ais 5 oy m AN d 3x3 Save Layout dcs a 10 nl 12 13 14 15 el GE 4ud MITSUBISHI SC wre MISE LIVE viewing is the default for Playback click on Live button one time Select Camera or Display for display format Select NETWORK from pull down menu to access more features For changing MENU via Remote go to CONFIG of NETWORK pull down menu For additional functions go to HELP pull down button and review OPERATIONS MENU Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved
16. will reset updating information and turn back on pa ue pep ETHERHET gt IP ADDRESS LERK 168 000 100 SUB HET MSK 255 295 255 000 GATEWAY 000 000 0020 000 DLOMHUMICATIOGM PORT SETTINGS RJ Eat B amp LARM NOTIFICATION SETTIN MO IF ADDRESS TARGET OWN 1 000 000 000 000 25111 01111 E 000 000 000 000 S5111 01112 3 000 000 000 000 95111 01113 4 000 000 000 000 S5111 01114 ETHERNET SERVICE PORT SETTING BL amp emRH MOTIFICATION SETTING 2 000 000 000 000 35111 01115 FBC ADDRESS gt R sB Qg U 2E aF FF WARNING PLEASE PRESS SET UP BUTTON TO APPLY MEW SETTING RETRY TIME COMMUNICATION PORT SETTINGS ETHERNET Page 56 ALARM NOTIFICATION SETTING Pages 55 57 Pages 58 57 Copyright 2004 Mitsubishi Digital Electronics America Inc All Rights Reserved 7 L Establishing a Network Connection The DVR can be connected by WEB BROWSER or DX PC25U software e WEB Browser Launch your Web Browser and at the ADDRESS LINE input the DVRs IP address USER ID default is root no and lower case PASSWORD default is admin000 no and lower case also 000 are zeros not letter o 3 Click on LOGIN button Up to 10 users can log in at one time NO m 44 1L2500 UserPassword Microsoft Internet Explorer Mm E File Edit Yiew Favorites Tools Help Back gt fat A Search G Favorites PMedia c4 Eh 3 aga M Address e http 216 237 45 12
Download Pdf Manuals
Related Search