Mitsubishi Electronics 3DC-100S Projection Television User Manual
Contents
1. On Hold POWER button for about two seconds Red LED will blink three times Off 50 20 ft 5 ft 50 Operating Range Be from 5 to 20 feet away Notes On the 3D Glasses Shut off 3D glasses when not in use to extend battery life Fluorescent and halogen lighting can cause the 3D glasses to flicker Turn off these lamps if flickering occurs Turning off the TV s 3D mode or changing the TV s input to a 2D input will turn off the IR emitter the glasses will turn off automati cally after two minutes Moving out of range of the IR emitter for more than two minutes will cause the glasses to turn off automatically Interference from other IR sources such as motion detection devices may cause the glasses to flicker or work intermittently Turn off other IR source if interference occurs The IR emitter in this system can also be used with Samsung 3D glasses model SSG 2100AB Information about these glasses can be obtained from Samsung USA at www samsung com usa You can also check www mitsubishi tv com for any updates about compatible glasses For assistance call 1 800 332 2119 11 Cleaning Instructions To avoid scratching the glasses use only standard glasses lens cleaning cloth microfiber cloth or a soft non scratching cloth such as cotton flannel Make sure the cloth is clean and free of any foreign material that may scratch the glasses Cloths pre moist2. 76 Series Tested Model HL T6176S Other Models HL T5076S HL T5676S 87 Series Tested Model HL T5687S Other Models HL T5087S HL T6187S 88 Series not tested HL T7288S 89 Series not tested HL T5089S HL T5689S HL T6189S Samsung 3D Ready DLP TVs Compatibility with 3DC 100S Adapter Mitsubishi has tested the 3DC 100S with representative models from several series of Samsung 3D Ready DLP HDTVs Mitsubishi has not tested all Samsung 3D Ready DLP HDTV models or series and cannot guarantee compatibility with non tested models or series Samsung 3D Ready Plasma TVs are not compatible with the 3DC 100S The Samsung models listed here are models that have been tested at the time of printing Normally all models from the same series will operate the same way and have the same compatibility Mitsubishi continues to test additional models when they are avail able For updates to the list of tested models please check the Owner s Guide for the 3DC 100S on line at www mitsubishi tv com For assistance call 1 800 332 2119 5 Battery Installation Emitter 1 2 1 Remove the cover 2 Insert the battery positive side up Be sure the retaining clip holds the battery securely 3 Reinstall the cover To remove the battery press on the retaining clip The remote control requires one CR2025 lithium battery 3D Adapter IR Sensor POWER Light Lit when power is on 3D STATUS Light Lit du
3. 3D Starter Pack MODEL 3DC 100S OWNER S GUIDE For questions Visit our website at www mitsubishi tv com E mail us at TVSupport mevsa com Call Consumer Relations at 800 332 2119 for operational or connection assistance To order replacement or additional remote controls or other accessories visit our website at www mitsuparts com or call 800 553 7278 Please check www mitsubishi tv com for updates on 3D signals and safety 2 Product 3D Adapter Model 3DC 100S Responsible Party Mitsubishi Electric Visual Solutions America Inc 9351 Jeronimo Rd Irvine CA 92618 1904 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful inter ference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communi cations However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving a
4. 4 and 3D video capabilities Connecting the Adapter continued Notice Concerning Samsung 720p TVs The adapter is not fully compatible with an A V receiver when used with Samsung 720p TVs models HL T4675S HL T5075S HL T5675S Always connect the 3D source device directly to the 3DC 100S adapter if using one of these TV models Please check www mitsubishi tv com for updates on 3D signals and safety 8 Using the Adapter 1 Position the emitter where there will be a clear path to the 3D glasses 2 Power on the TV the 3D video device and the 3D glasses Note The 3D video device must be powered on before the 3D Adapter can power on 3 If the 3D Adapter does not power on automatically when you power on the 3D video device press the POWER button 4 Mitsubishi TV only If the New Input Found screen displays assign a name to the input If you have an 833 series TV name the input Game 5 Start video from the 3D video device and wait a few moments for an image to appear 6 Enable the TV s 3D mode For a Mitsubishi 833 series TV 3D set tings are in the FX Gaming menu If you have a Samsung TV see the TV owner s guide 7 Select the Adapter s 3D mode Press the 3D MODE button to change For ordinary 2D signals keep the Adapter powered on and use 3D Mode Normal For automatic detection of HDMI 1 4a 3D signals use 3D Mode Normal For non HDMI 1 4a 3D signals press the 3D MODE button repeated
5. ES EMITTER HDMI OUT HDMI IN 3D GLASSES EMITTER IN 5V DC 2A 3D GLASSES EMITTER OUT TV TV Emitter provided AC power adapter provided HDMI cable provided HDMI input Source device HDMI cable DIN cable provided Step 1 Step 2 Step 5 Step 7 Step 3 Step 4 Power on the TV Step 6 Power on the source device Connecting the Adapter Connecting a Single 3D Video Source Power off all devices prior to connecting the Adapter If the device was in use prior to adding the Adapter use the same TV input if possible On a Mitsubishi 833 series TV the input must be named Game For Samsung TVs use the input labelled HDMI DVI You may need to name the input PC See your Samsung owner s guide for details For assistance call 1 800 332 2119 7 Connecting Multiple 3D Video Sources 1 2 3 HDMI Pb Pr INPUT 2 INPUT 1 DIGITAL AUDIO OUTPUT 480i 480p 720p 1080i Y VIDEO Pb Pr Y VIDEO DVI PC L R INPUT AUDIO 3D GLASSES EMITTER ANT AUDIO L R AUDIO OUTPUT L R LAN TV A V receiver HDMI cables HDMI cables Adapter Source devices Connect devices with checkerboard output directly to the TV Enable checkerboard output from the devices if needed If using a newer A V receiver you may be able to connect devices to the A V receiver as shown below The A V receiver must support HDMI 1
6. ICE a Contact Mitsubishi Electric Visual Solutions America Inc MEVSA by calling 800 332 2119 The Consumer Relations Representative at this phone number will provide you with the details AND when necessary authorizations for the return of the kit or parts for repair DO NOT send the product or part for repair without the proper authorizations b Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service Present your sales receipt or other docu ment which establishes proof and date of purchase upon request by MEVSA THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY However please return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you 2 THIS LIMITED WARRANTY DOES NOT COVER a Consumable parts such as batteries 3D Glasses and IR Emitters that were not sold as a part of the Starter Kit refer to the instructions for the separately purchased glasses and IR Emitter for warranty details cosmetic damage or any other damage where such damage is caused by unauthorized modification alteration repairs to or service of the product by anyone other than an autho Please check www mitsubishi tv com for updates on 3D signals and safety 14 rized MITSUBISHI service center physical abuse to or misuse of the product including any failure to carry out any maintenance as described
7. ND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR 4 UNDER NO CIRCUMSTANCES SHALL MEVSA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL SPECIAL OR CONSEQUEN TIAL DAMAGES WHETHER ARISING OUT OF BREACH OF WARRANTY BREACH OF CONTRACT OR OTHERWISE 5 Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental special or consequential damages so the above limitations or exclusions may not apply to you 6 This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA INC 9351 Jeronimo Road Irvine CA 92618 1904 3DC 100S 2011 Mitsubishi Electric Visual Solutions America Inc 853B710B80
8. ases ledges or balconies You may risk falling during or after use Epilepsy WARNING IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY CONSULT A PHYSICIAN BEFORE USING 3D VIDEO OR GAME PRODUCTS A small percentage of the population may experience epileptic seizures when viewing certain types of TV images or video games that contain flashing patterns of light The following people should consult a physician before viewing 3D Games or Video Anyone with a history of epilepsy or who has a family member with a history of epilepsy Anyone who has ever experienced epileptic seizures or sensory disturbances trig gered by flashing light effects WARNING SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY DISCONTINUE 3D VIEWING IF YOU EXPERI ENCE ANY OF THE FOLLOWING SYMPTOMS Involuntary movements eye or muscle twitching Muscle cramps Nausea dizziness or queasiness Convulsions Disorientation confusion or loss of awareness of your surroundings Do not engage in any potentially hazardous activity for example driving a vehicle until your symptoms have completely gone away Do not resume 3D viewing without discussing the symptoms with your physician For assistance call 1 800 332 2119 13 Mitsubishi Model 3DC 100S 3D Starter Kit Limited Warranty MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA INC MEVSA war rants as follows to the ori
9. ened with cleaning solutions designed specifi cally for eye glasses can be used however do not spray solutions directly on the glasses DO NOT spray any cleaner directly onto the any surface of the glasses This may result in fire electric shock damage to the product surface or removal of control labels DO NOT use chemicals containing alcohol solvents surfactants wax benzene thinners insect repellents lubricants or household cleaners These may result in discoloration removal of control labels or cracks to the product surfaces Caution Do not place the product in a location exposed to direct sunlight heat fire or water This may result in product malfunction or fire Do not apply force to the lenses of the 3D glasses Do not drop or bend the product This may result in product malfunction Troubleshooting If you encounter Try this My 3D glasses do not operate Replace the battery if it is drained Focus your 3D glasses toward the TV front Make sure that the distance from the TV to the glasses is less than 20 feet in a straight line Check if the emitter LED is lit If not make sure the TV s 3D mode is turned on and the emitter is plugged in The LED blinks continually The battery is drained Replace it with a new one Please check www mitsubishi tv com for updates on 3D signals and safety 12 3D Safety Requirements 3D Glasses are NOT desig
10. ginal purchaser of this 3D Starter Kit from an autho rized MITSUBISHI Audio Video Dealer should the adapter glasses IR emitter remote control or included accessories prove defective by reasons arising from improper workmanship and or material a Length of Warranty The Starter Kit including the 3D adapter 3D glasses and IR emitter and all included parts except for consumable parts such as batteries are warranted for a period of one 1 year from the date of the original purchase at retail We will repair or replace at our option any defective part without charge Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured Parts used for replace ment are warranted for the remainder of the original warranty period b Send In Service MEVSA provides send in service only The owner is respon sible for packaging the full kit or parts for repair safely and the shipping costs to the MEVSA designated service location MEVSA will repair or replace and return the items without charge for return shipping c Notice To obtain warranty service you must notify Mitsubishi Electric Visual Solutions America Inc of any defect within the applicable warranty time period BEFORE REQUESTING SERVICE please review the instruction booklet to insure proper installation and correct customer control adjustment If the problem persists please arrange for warranty service 1 TO OBTAIN WARRANTY SERV
11. in the Owner s Guide or any product damaged by excessive physical or electrical stress any products that have had a serial number or any part thereof altered defaced or removed product use in any manner contrary to the Owner s Guide freight damage or any damage caused by acts of God or other factors beyond the reasonable control of MEVSA such as power surge damage caused by electri cal system or lightning This limited warranty also excludes service where no defect in the product covered under this warranty is found service related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty all costs expenses or any other damages arising from product installation or set ups any adjust ments of user controls including contrast brightness color tint fine tuning sharpness to the connected TV other adjustment necessary to prepare the unit for display or use connection with any external audio receiver antenna cable or satellite systems or service of products purchased or serviced outside the U S A Please consult the operating instructions contained in the Owner s Guide furnished with the product for information regarding user controls 3 ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY REMEDY WHICH BUT FOR THIS PROVISION MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW IS HEREBY EXCLUDED AND DISCLAIMED THE IMPLIED WARRANTIES OF MERCHANTABILITY A
12. ly until the picture appears correct Picture Troubleshooting Blurry double image checkerboard format Turn on TV s 3D mode Press 3D MODE button to select 3D Mode Normal Two images top and bottom format Press 3D MODE button to select 3D Mode for top bottom Two images side by side format Press 3D MODE button to select 3D Mode for side by side For assistance call 1 800 332 2119 9 3D active LCD shutter glasses enable you to view 3D images when used with the matching IR emitter and a compatible 3D ready TV 3D Glasses Battery Cover Power Button LED Indicator LCD Shutter Lens Battery Installation Each pair of glasses requires one CR2025 lithium battery A continuously blinking red LED indicates low battery power Install a new battery See lithium battery safety information at the front of this booklet Open the cover Remove the old battery if present Insert a new battery positive side facing out Close the cover Emitter LED Lit when TV is in 3D mode Please check www mitsubishi tv com for updates on 3D signals and safety 10 Using the 3D Glasses 3D Glasses Operation 1 Turn on 3D Mode in the TV and 3D source device 2 Press the POWER button on the glasses to turn on the glasses 3 When the 3D program is complete turn off 3D mode in the TV and 3D source device and turn off the glasses Press POWER button The red LED will light for three seconds
13. ned as sunglasses or safety glasses and do not provide protection 3D glasses should be worn only when viewing 3D material Do not wear the wireless glasses in any situations that require unimpaired visual perception Children under the age of 5 should not view 3D programming Under normal conditions 3D viewing is safe for your movies or games Some people may experience discomfort however To minimize the potential for experiencing visual problems or any adverse symptoms Read and follow any and all safety warnings that accompany your 3D glasses or 3D source devices Maintain a distance of no less than 2 to 2 5 times the screen height measurement away from the display Viewing from too short a distance can strain your eyes Take regular breaks at least 5 minutes after every hour of 3D viewing If you experience any of the following symptoms discontinue 3D viewing until the symp toms go away nausea dizziness or queasiness headache or eyestrain blurry vision double vision that lasts longer than a few seconds Do not engage in any potentially hazardous activity for example driving a vehicle until your symptoms have completely gone away If symptoms persist discontinue use and do not resume 3D viewing without discussing your symptoms with a physician Do not use the glasses where loss of balance or limiting your field of vision may be dangerous to you Do not use near stairc
14. ntenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an expe rienced radio TV technician for help FCC Information 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 8 Only use attachments accessories specified by the manufacturer 9 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Important Safety Instructions WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture For assistance call 1 800 332 2119 3 Features Converts 3D video originating in several popular formats to checker board format for display on your 3D or 3D ready Mitsubishi television or 3D ready Samsung DLP television Processes side by side top and bottom and frame packing 3D e g Blu
15. ray 3D formats Passes 2D images unaltered for normal display Includes two pairs of active shutter 3D glasses and matching IR emitter Compatible with these Mitsubishi television models 3D Ready Televisions 2007 through 2010 833 series 2007 L65 A90 2008 L75 A91 2010 C8 series 2008 737 series 2009 638 series 2010 735 series 2008 837 series 2009 C10 series 2010 736 series 2008 C9 series 2009 835 series 2008 L75 A81 2010 3D Televisions starting in 2010 738 series 2010 838 series 2010 Use and Compatibility The Mitsubishi 3D Adapter Model 3DC 100S may be used to display 3D content only when connected to a Mitsubishi 3D Ready DLP TV Samsung 3D Ready DLP TV or a Mitsubishi 3D TV When using the Mitsubishi 3D adapter a 3D source device connected to the Mitsubi shi 3D adapter is required to support the display of 3D games 3D broadcasts from terrestrial cable satellite and 3D Blu ray disc content Mitsubishi 738 and 838 Series TVs with software version of 012 06 or higher do not require the use of the adapter for HDMI 1 4a mandatory 3D signals Please check www mitsubishi tv com for updates on 3D signals and safety 4 650 Series Tested Model HL61A650C1F Other Models HL50A650C1F HL56A650C1F HL72A650C1F 750 Series Tested Model HL61A750A1F Other Model HL67A750A1F 75 Series Tested Model HL T5075S Other Models HL T4675S HL T5675S
16. ring 3D signal processing POWER Button Allows manual override of auto on off Press to power off the Adapter if it powers on when not needed 3D MODE Button Allows manual selection of 3D format conversion Controls and Indicators POWER 3D MODE POWER POWER 3D MODE 3D STATUS Adapter Remote Control Lithium Battery Safety This product uses CR2025 Li MnO2 lithium coin batteries WARNING Lithium coin cell batteries pose a serious risk of injury if ingested Keep cells out of reach of children If ingested immediately contact a physi cian or the National Poison Center at 202 625 3333 CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type CR2025 CAUTION Risk of fire and burns Do not recharge disassemble heat above 100 C 212 F or incinerate Keep battery out of reach of children Disposal Dispose of used batteries promptly according to local recycling or waste regulations Please check www mitsubishi tv com for updates on 3D signals and safety 6 3D GLASSES EMITTER OUT 3D GLASSES EMITTER IN HDMI OUT HDMI IN 5V DC 2A 3D GLASSES EMITTER OUT 3D GLASSES EMITTER IN HDMI OUT HDMI IN 5V DC 2A 3D GLASSES EMITTER OUT 3D GLASSES EMITTER IN HDMI OUT HDMI IN 5V DC 2A 3D GLASSES EMITTER OUT 3D GLASSES EMITTER IN HDMI OUT HDMI IN 5V DC 2A 3D GLASSES EMITTER OUT 3D GLASSES EMITTER IN HDMI OUT HDMI IN 5V DC 2A 3D GLASS
Download Pdf Manuals
Related Search