Home

Milwaukee 2707-20 Drill User Manual

image

Contents

1. ASSEMBLY OPERATION A WARNING Recharge only with the charger specified for the battery For specific charging instructions read the operator s manual supplied with your charger and battery Inserting Removing the Battery To remove the battery push in the release buttons and pull the battery pack away from the tool To insert the battery slide the pack into the body of the tool Make sure it latches securely into place WARNING Always remove battery pack before changing or removing acces sories Only use accessories specifically recommended for this tool Others may be hazardous Bit Selection Use sharp bits Sharp bits are less likely to bind when drilling Use the proper bit for the job There are many types of bits designed for specific purposes Check the information on the bit s packaging for proper usage Do not use bits larger than the rated capacity of the drill Gear damage or motor overload may result see Specifications Installing Bits Always remove the battery before inserting or removing bits Select the proper style and size bit for the application Installing Bits into Keyed Chucks Cat No 2707 20 1 Remove the battery pack 2 Open the chuck jaws wide enough to insert the bit Be sure the bit shank and chuck lt jaws are clean Dirt particles may prevent the bit from lin ND ing up properly lm 3 Insert the bit into the c
2. s quiet OPERATOR S MANUAL MANUEL de L UTILISATEUR MANUAL del OPERADOR Cat No No de cat FOLIE GAMA M18 FUEL HOLE HAWG RIGHT ANGLE DRILLS PERCEUSE HOLE HAWG M18 FUEL DE ELECTRICIEN TALADRO HOLE HAWG DE M18 FUEL PARA ELECTRICISTAS I EDGE THE RISK OF INJURY USER MUST READ AND UNDERSTAND OPERATOR S AFIN DE R DUIRE LE RISQUE DE BLESSURES L UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L UTILISATEUR PARA REDUCIR EL RIESGO DE LESIONES EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR GENERAL POWER TOOL SAFETY WARNINGS cordless power tool WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated WORK AREA SAFETY Keep work area clean and well lit Cluttered or dark areas invite accidents Do not operate power tools in explosive atmos pheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fume
3. un centre de ser vice MILWAUKEE accr dit afinqu on en effectue la r paration voir R parations A AVERTISSEMENT Pour minimiser les risques de blessures ou de dommages l outil n immergez jamais l outil la batterie ou le chargeur et ne laissez pas de liquide s y infiltrer Nettoyage D barrassez les vents du chargeur et de l outil des d bris et de la poussi re Gardez les poign es de l outil propres sec et exemptes d huile ou de graisse Le nettoyage de l outil du chargeur et de la batterie doit se faire avec un linge humide et un savon doux Certains nettoyants tels l essence la t r benthine lesdiluants laque ou peinture les solvants chlor s l ammoniaque et les d tergents d usage domestique qui en contiennent pourraient d t riorer le plastique et l isolation des pi ces Ne laissez jamais de solvants inflammables ou com bustibles aupr s de l outil R parations Pour les r parations retournez outil batterie et chargeur en entier au centre service le plus pr s 12 ACCESOIRES Pour une liste compl te des accessoires pri re de se reporter au catalogue MILWAUKEE Electric Tool ou visiter le site internet www milwaukeetool com Pour obtenir un catalogue il suffit de contacter votre distributeur local ou l un des centres service A AVERTISSEMENT Retirez toujours la batterie avant de changer ou d enlever les accessoires L utilisation d aut
4. AMERICA CENTRAL Y EL CARIBE TECHTRONIC INDUSTRIES garantiza por 5 a os este producto a partir de la fecha original de compra Esta garant a cubre cualquier defecto que presenten las piezas componentes y la mano de obra contenidas en este producto Para Am rica Central y el Caribe se debe confirmar en el Centro de Servicio Autorizado el plazo de la garant a Para hacer efectiva la Garant a deber presentar al Centro de Servicio Autorizado la P liza de Garant a sellada por el establecimiento en donde adquiri el producto Si no la tienen podr presentar el comprobante de compra original Usted puede llamar sin costo al tel fono 01 800 832 1949 o por correo electr nico a la direcci n servicio ttigroupna com para ubicar el Centro de Servicio Autorizado m s cercano a su domicilio en el cual adem s podr adquirir partes componentes consumibles y accesorios que usted necesite Procedimiento para hacer v lida la garant a Limpie el polvo y suciedad de las ventilas del cargador y la herramienta Mantenga los mangos y empu aduras limpios secos y libres de aceite o grasa Use solo jab n neutro y un trapo h medo para limpiar la herramienta bater a y el cargador ya que algunos substancias y solventes limpiadores son da inos a los pl sticos y partes aislantes Algu nos de estos incluyen gasolina turpentina thiner lacas th ner para pinturas solventes para limpieza con cloro amon aco y detergentes caseros que
5. Power Source and Trade Titan Indus trial Work Carts is one 1 year from the date of purchase The warranty period for a LED Work Light and LED Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only if during normal use the LED bulb fails the Work Light or Upgrade Bulb will be replaced free of charge This warranty does not cover Air Nailers amp Stapler Airless Paint Sprayer Cordless Battery Packs Gasoline Driven Portable Power Generators Hand Tools Hoist Electric Lever amp Hand Chain M12 Heated Jackets Reconditioned product and Test amp Measurement products There are separate and distinct warranties avail able for these products Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time warranty service is requested ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT IF YOU DO NOT AGREE TO THIS CONDITION YOU SHOULD NOT PURCHASE THE PRODUCT IN NO EVENT SHALL MIL WAUKEE BE LIABLE FOR ANY INCIDENTAL SPECIAL CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR ANY COSTS ATTORNEY FEES EXPENSES LOSSES OR DELAYS ALLEGED TO BE AS ACONSEQUENCE OF ANY DAMAGE TO FAILURE OF OR DEFECT IN ANY PRODUCT INCLUDING BUT NOT LIMITED TO ANY CLAI
6. Use brocas afiladas Es menos probable que las brocas afiladas se atoren durante el taladrado Use la broca correcta para el trabajo Hay muchos tipos de brocas dise ados para fines espec fi cos Revise la informaci n proporcionada en el envoltorio de la broca para obtener informaci n Sobre el uso adecuado No use brocas de mayor tama o que la capa cidad nominal del taladro Podr an da arse los engranajes u ocurrir una sobrecarga del motor vea Especificaciones Instalaci n de brocas Antes de introducir o retirar las brocas siempre se debe retirar la bater a Seleccione la broca del estilo y el tama o adecuados para el tipo de tornillo que est usando Instalaci n de brocas en los mandril con cha veta Cat No 2707 20 1 Extraer la bater a 2 Abra las mordazas del man 7 dril lo suficiente para poder insertar la broca Aseg rese que el v stago de la broca y las mordazas del mandril est n limpios Las part culas de suciedad pueden evitar el alineamiento cor recto de la broca 3 Inserte la broca en el mandril Centre la broca en las mordazas del mandril y lev ntela aproxi 16 ESPECIFICACIONES Capacidades Acero Madera Volts Broca Broca de Broca de Sierra Cat No cd rpm helicoidal berbiqu auto alimentaci n perforadora 2707 20 18 0 1200 8mm 5 16 32 mm 1 1 4 51 mm 2 102 mm 4 2708 20 18 0 1200 8mm 5 16 32 mm 1 1 4 51 mm 2 102 mm 4 ENSAMBLAJE
7. auto avance align es avec la surface de travail pour qu elles percent en ligne droite voir Per age vitez de percer des mat riaux ondul s humides noueux et ou en mauvais tat Evitez de percer des mat riaux qui pourraient contenir des clous cach s ou d autres l ments qui risquent de coincer la m che La direction de la r action est toujours l oppos de la direction de la rotation Une r action est encore plus pr visible lorsque vous largissez des trous existants et au point o la m che perce l autre c t du mat riau Si la m che se coince 1 Rel chez imm diatement la g chette 2 Inversez le sens de rotation du moteur 3 Retirez la m che de la pi ce et recommencez 4 N appuyez pas sur la g chette pour la rel cher imm diatement afin d essayer de d gager une m che coinc e Ceci va endommager la m che Maintien ferme pour une rotation avant Si vous percez vers l avant la m che tourne dans le sens horaire Si la m che se coince dans le trou elle s arr te soudainement et r agit en tournant dans le sens antihoraire Un exemple d une foreuse Hole Hawg correcte ment tay e pour la rotation avant A Rotation vers l avant sens horaire B R action C Etayez la foreuse en pla ant le bo tier du moteur ici Si la m che se coince le bo tier maintenus ferme ment contre le montant maintiendront la position de la m che Maintien ferme po
8. tengan amonia Nunca usa solventes inflamables o combustibles cerca de una herramienta Reparaciones Si su herramienta bater a o cargador est n da ados env ela al centro de servicio m s cercano 6 18 Acuda al Centro de Servicio con el producto y la poliza de garant a sellada por el establecimiento donde realiz la compra Ahi se reem plazar cualquier pieza o componente defectuoso sin cargo alguno para el usuario final La empresa se hace responsable de los gastos de transportaci n razonablemente erogados que se deriven del cumplimiento de la presente garant a Excepciones La garant a perder validez en los siguientes casos a Cuando el producto se hubiese utilizado en condiciones distintas a las normales b Cuando el producto no hubiese sido operado de acuerdo con el instructivo de uso que le acompa a c Cuando el producto hubiese sido alterado o reparado por personas no autorizadas por TECHTRONIC INDUSTRIES Nota Si el cord n de alimentaci n es da ado este debe ser remplazado por el fabricante o por un Centro de Servicio Autorizado para evitar riesgo un inicio a la broca y evitar que se desvie Lubrique la broca para taladro con aceite para corte cuando taladre en hierro o acero Utilice un refrigerante cuando taladre en metales no ferrosos como cobre laton o aluminio 3 Aplique siempre presion en linea con la broca Utilice suficiente presion para mantener el tal adro perforando pero no demasiada
9. ESTA CONDICI N NO DEBE COMPRAR EL PRODUCTO MILWAUKEE NO SER EN NING N CASO RESPONSABLE DE DANOS INCIDENTALES ESPECIALES CONSECUENTES O PUNITIVOS NI DE COSTOS HONORARIOS DE ABOGADOS GASTOS P RDIDAS O DEMORAS SUPUESTAMENTE CAUSADOS COMO CONSECUENCIA DE CUALQUIER DANO FALLA O DEFECTO EN CUALQUIER PRODUCTO INCLUIDOS A MODO DE EJEMPLO RECLAMOS POR P RDIDA DE GANANCIAS ALI GUNOS ESTADOS NO PERMITEN LA EXCLUSI N O LA LIMITACI N DE DA OS INCIDENTALES O CONSECUENTES POR LO TANTO LAS LIMITACIONES Y EXCLUSIONES ANTERIORES PUEDEN NO APLICARSE PARA USTED ESTA GARANT A ES EXCLUSIVA Y SUSTITUYE A TODAS LAS OTRAS GARANT AS EXPRESAS ESCRITAS U ORALES SEG N LO PERMITA LA LEY MILWAUKEE SE EXIME DE TODA GARANT A IMPL CITA INCLUIDOS A MODO DE EJEMPLO TODA GARANT A IMPL CITA DE COMERCIABILIDAD O IDONEIDAD PARA UN USO O PROPOSITO EN PARTICULAR EN LA MEDIDA EN QUE DICHA RE NUNCIA NO EST PERMITIDA POR LA LEY DICHAS GARANT AS IMPL CITAS EST N LIMITADAS A LA DURACI N DE LA GARANT A EXPRESA APLICABLE SEG N SE DESCRIBE ANTERIORMENTE ALGUNOS ESTADOS NO PERMITEN LIMITACIONES EN LA DURACI N reforzar el material a fin de evitar daiar la pieza de trabajo 2 Cuando vaya a iniciar una perforacion coloque la broca sobre la superficie de trabajo y aplique presion Para que comience a girar una broca de auto Si la herramienta no arranca u opera a toda su potencia con una bater a completamente cargada limpie con una
10. L utilisation de ces dispositifs peut r duire les risques li s aux poussi res UTILISATION ET ENTRETIEN DE L OUTIL ELECTRIQUE Ne pas forcer l outil lectrique Utiliser l outil lectrique appropri l application consid r e L outil lectrique adapt au projet consid r pro duira de meilleurs r sultats dans des conditions de s curit meilleures la vitesse pour laquelle il a t concu Ne pas utiliser l outil lectrique si le commuta teur ne le met pas sous ou hors tension Tout outil lectrique dont le commutateur de marche arr t est inop rant est dangereux et doit tre r par D brancher la fiche de la prise d alimentation et ou la batterie de l outil lectrique avant d effectuer des r glages de changer d accessoires ou de ranger l outil De telles mesures de s curit pr ventive r duisent le risque de mettre l outil en marche accidentellement Ranger les outils lectriques inutilis s hors de la port e des enfants et ne pas laisser des personnes qui connaissent mal les outils lec triques ou ces instructions utiliser ces outils Les outils lectriques sont dangereux dans les mains d utilisateurs non form s leur usage Entretien des outils lectriques S assurer de jours porter une protection oculaire Selon les g l absence de tout d salignement ou de grip page des pi ces mobiles de toute rupture de piece ou de toute autre condition qui pour rait affecter le bo
11. goma o borrador los contactos de la bater a y de la herramienta Si aun asi la her ramienta no trabaja correctamente regr sela con el cargador y la bater a a un centro de servicio DE UNA GARANT A IMPL CITA POR LO TANTO LA LIMITACI N ANTERIOR PUEDE NO APLICARSE PARA USTED ESTA GARANT A LE OTORGA DERECHOS LEGALES ESPEC FICOS Y TAMBI N PUEDE TENER OTROS DERECHOS QUE VAR AN DE ESTADO EN ESTADO Esta garant a se aplica a los productos vendidos en los EE UU y Canad Consulte Service Center Search B squeda de centro de servicio en la secci n Parts 8 Services Piezas y servicios del sitio web MILWAUKEE www milwaukeetool com o llame al 1 800 SAWDUST 1 800 729 3878 para encontrar su Centro de Servicio de la f brica de MILWAUKEE m s cercano alimentacion introduzca el tornillo roscado en la pieza de trabajo oprimiendo el interruptor de accionamiento y dejando que la broca gire por inercia hasta que los dientes hagan contactocon la superficie de trabajo Alinee correctamente la broca antes de proseguir Esto evitar que se desvie y se atasque durante el arranque Al taladrar en metal marque el centro del agu jero a taladrar con un punzon central para dar MILWAUKEE para que sea reparada A ADVERTENCIA Para reducir el riesgo de una explosi n no queme nunca una bater a aun si est da ada muerta o completamente descargada Limpieza POLIZA DE GARANT A VALIDA SOLO PARA MEXICO
12. is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically desig nated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire Under abusive conditions liquid may be eject ed from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help a ae ejected from the battery may cause irritation or burns SERVICE Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained SPECIFIC SAFETY RULES Use auxiliary handle s if supplied with the tool Loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Maintain labels and nameplates These carry important information If unreadable or mi
13. madamente 1 6 mm 1 16 por encima de la parte inferior del mandril Apriete las mordazas del mandril con la mano para alinear la broca 4 Coloque la chaveta del mandril en cada uno de los tres orificios en el mandril y g rela en el sentido de las manecillas del reloj para apretar firmemente el mandril NOTA Nunca use una llave u otra herramienta excepto la chaveta del mandril para apretar o aflojar el mandril 5 Para extraer la broca coloque la chaveta del mandril en uno de los tres orificios ubicados en el mandril y g rela en sentido contrario a las manecillas del reloj Instalaci n de brocas en los mandriles Hex agonal 11 mm 7 16 Cat No 2708 20 1 Extraer la bater a 2 Para instalar un accesorio presione la base en el portabrocas del hexagonal 3 Para quitar el accesorio jale del aro y quite el accesorio Suelte el aro OPERACION A ADVERTENCIA Para reducir el riesgo de lesiones extraiga siempre la bateria antes de acoplar o desacoplar accesorios Utilice unicamente accesorios especificamente re comendados para esta herramienta El uso de accesorios no recomendados podria resultar peligroso A ADVERTENCIA Para reducir el riesgo de lesiones use siempre lentes de se guridad o anteojos con protectores laterales A ADVERTENCIA Para reducir el riesgo de lesiones personales durante el taladrado sujete la herramienta por las superficies de sujecion aisladas cuando realice una op
14. properly before proceeding This will reduce cocking and jam ming when starting When drilling in metal mark the center of the hole to be drilled with a center punch to give the bit a start and to prevent it from walking Lubricate the drill bit with cutting oil when drilling iron or steel Use a coolant when drilling nonferrous metals such as copper brass or aluminum 3 Always apply pressure in line with the bit Use enough pressure to keep the drill biting but do not push hard enough to cause the bit to bind When using twist drill bits pull the bit out fre quently to clear chips from the flutes When using selfeed bits if the clutch slips pull the bit up very slightly and then push it toward the workpiece Repeat this several times 4 Reduce pressure and ease the bit through the last part of the hole While the tool is still running pull the bit out of the hole to prevent jamming When using selfeed bits decrease the drilling pressure when the feed screw point breaks through the workpiece Proceed with steady even pressure MAINTENANCE A WARNING To reduce the risk of injury always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance Never disassem ble the tool battery pack or charger Contact a MILWAUKEE service facility for ALL repairs Maintaining Tool Keep your tool battery pack and charger in good repair by adopting a regular maintenance program After
15. que pueda ocasionar el atoramiento de la broca Cuando use brocas helicoidales tire de la broca hacia afuera para eliminar las rebabas de las estrias Cuando use brocas de autoalimentacion si se desliza el embrague tire ligeramente de la broca hacia arriba y luego empujela hacia la pieza de trabajo Repita este procedimientovarias veces CENTRO DE SERVICIO Y ATENCI N A CLIENTES Av Presidente Mazarik 29 Piso 7 11570 Chapultepec Morales Miguel Hidalgo Distrito Federal Mexico Tel 52 55 4160 3547 IMPORTADO Y COMERCIALIZADO POR TECHTRONIC INDUSTRIES MEXICO S A DE C V Av Presidente Mazarik 29 Piso 7 11570 Chapultepec Morales Miguel Hidalgo Distrito Federal Mexico Modelo Fecha de Compra Sello del Distribuidor UNITED STATES MILWAUKEE Service MILWAUKEE prides itself in producing a premium quality product that is NoTHING But Heavy Durv Your satisfaction with our products is very impor tant to us If you encounter any problems with the operation of this tool or you would like to locate the factory Service Sales Support Branch or authorized service station nearest you please call Additionally we have a nationwide network of authorized Distributors ready to assist you with yourtool and accessory needs Check your Yellow Pages phone directory under Tools Electric for the names amp addresses of those nearest you or see the Where To Buy section of our website 1 800 SAWDUST 1 800 729 3
16. removing ac cessories Only use accessories specifically recommended for this tool Others may be hazardous For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go online to www milwaukeetool com To obtain a catalog contact your local distributor or service center LIMITED WARRANTY USA AND CANADA Every MILWAUKEE power tool including cordless product tool battery pack s see separate amp distinct CORDLESS BATTERY PACK LIMITED WARRANTY statements amp battery charger and Work Lights is war ranted to the original purchaser only to be free from defects in material and workmanship Subject to certain exceptions MILWAUKEE will repair or replace any part on an electric power tool which after examination is determined by MILWAUKEE to be defective in material or workmanship for a period of five 5 years after the date of purchase unless otherwise noted Return of the power tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station freight prepaid and insured is required A copy of the proof of purchase should be included with the return product This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized personnel misuse alterations abuse normal wear and tear lack of maintenance or accidents The warranty period for Job Site Radios M12 Power Port M18
17. site www milwaukeetool com MILWAUKEE est fier de proposer un produit de premi re qualit NotHinc Bur Heavy Durv Votre satisfaction est ce qui compte le plus En cas de probl mes d utilisation de l outil ou pour localiser le centre de service ventes ou le centre d entretien le plus proche appelez le 1 800 268 4015 Lundi Vendredi 7 00 4 30 CST fax 866 285 9049 Milwaukee Electric Tool Canada Ltd 140 Fernstaff Court Unit 4 18129 111 Avenue NW Vaughan ON L4K 3L8 Edmonton AB T5S 2P2 Notre r seau national de distributeurs agr s se tient votre disposition pour fournir l aide technique l outillage et les accessoires n cessaires Composez le 1 800 268 4015 pour obtenir les noms et adresses des revendeurs les plus proches ou bien consultez la section O acheter sur notre Site web l adresse www milwaukeetool com MEXICO Soporte de Servicio MILWAUKEE CENTRO DE ATENCION A CLIENTES Av Presidente Masarik 29 Piso 7 CP 11570 Col Chapultepec Morales Del Miguel Hidalgo Distrito Federal M xico 01 800 8321949 Lunes a Viernes 9am a 6pm O cont ctanos en www milwaukeetool com mx Para informaci n de Centros de Servicio busca el icono Servicio al cliente Cont ctanos Contacta nuestro servicio t cnico para Preguntas T cnicas Asesor a servicio y reparaci n Garant a Adicionalmente tenemos una red nacional de distribuidores autorizados listos para ayudarle con su herramienta
18. six months to one year depending on use return the tool battery pack and charger to a MILWAUKEE service facility for Lubrication Mechanical inspection and cleaning gears spindles bearings housing etc Electrical inspection battery pack charger motor Testing to assure proper mechanical and electrical operation If the tool does not start or operate at full power with a fully charged battery pack clean the contacts on the battery pack If the tool still does not work properly return the tool charger and battery pack to a MILWAUKEE service facility for repairs A WARNING To reduce the risk of personal injury and damage never immerse your tool battery pack or charger in liquid or allow a liquid to flow inside them Cleaning Clean dust and debris from charger and tool vents Keep tool handles clean dry and free of oil or grease Use only mild soap and a damp cloth to clean the tool battery pack and charger since certain cleaning agents and solvents are harmful to plastics and other insulated parts Some of these include gasoline turpentine lacquer thinner paint thinner chlorinated cleaning solvents ammonia and house hold detergents containing ammonia Never use flammable or combustible solvents around tools Repairs For repairs return the tool battery pack and char ger to the nearest service center ACCESSORIES JN DUET MAS Always remove battery pack before changing or
19. tool for forward rotation A Forward clockwise rotation B Reaction C Brace drill with motor housing here If the bit binds the motor housing braced against the stud will hold the drill in position Bracing for reverse rotation When drilling in reverse the bit will rotate in a coun terclockwise direction If the bit binds in the hole the bit will come to a sudden stop and the drill will suddenly react in a clockwise direction The following figure shows an example of properly bracing the tool for reverse rotation A Reverse counterclockwise rotation B Reaction C Brace drill with motor motor housing here If the bit binds the motor housing braced against the stud will hold the drill in position Using Control Switch The control switch may be set to three positions forward reverse and lock Due to a lockout mecha nism the control switch can only be adjusted when the trigger is not pulled Always allow the motor to come to a complete stop before using the control Switch For Forward clockwise rotation push the control switch from the left side of the tool Check the direction of rotation before use For Reverse counterclockwise rotation push the control switch from the right side of the tool Check direction of rotation before use To Lock the trigger push the control switch to the center position The trigger will not work while the control switch is in the center l
20. 878 Monday Friday 7 00 AM 6 30 PM Central Time or visit our website at www milwaukeetool com For service information use the Service Center Search icon found in the Parts amp Service section Contact our Corporate After Sales Service Technical Support about Technical Questions Service Repair Questions Warranty call 1 800 SAWDUST fax 1 800 638 9582 email metproductsupport milwaukeetool com Register your tool online at www milwaukeetool com and receive important notifications regarding your purchase ensure that your tool is protected under the warranty become a Heavy Duty club member CANADA Service MILWAUKEE MILWAUKEE prides itself in producing a premium quality product that is NorHiNa Bur Heavy Durv Your satisfaction with our products is very important to us If you encounter any problems with the operation of this tool or you would like to locate the factory Service Sales Support Branch or authorized service station nearest you please call 1 800 268 4015 Monday Friday 7 00 4 30 CST fax 866 285 9049 Milwaukee Electric Tool Canada Ltd 140 Fernstaff Court Unit 4 18129 111 Avenue NW Vaughan ON L4K 3L8 Edmonton AB T5S 2P2 Additionally we have a nationwide network of authorizedDistributors ready to assist you with your tool and accessory needs Call 1 800 268 4015 to find the names and addresses of the closest retailers or consult Where to buy on our Web
21. ECT DE DOMMAGES INT R TS PUNITIFS OU DE TOUTE D PENSE D HONORAIRES D AVOCATS DE FRAIS DE PERTE OU DE D LAIS ACCESSOIRES A TOUT DOMMAGE D FAILLANCE OU D FAUT DE TOUT PRODUIT Y COMPRIS NOTAMMENT LES PERTES DE PROFIT CERTAINS TATS ET PROVINCES NE PERMETTANT PAS L EXCLUSION OU LA LIMITATION DES DOMMAGES DIRECTS OU INDIRECTS LES RESTRICTIONS CI DESSUS PEUVENT NE PAS TRE APPLI CABLES CETTE GARANTIE EST EXCLUSIVE ET REMPLACE TOUTE AUTRE GARANTIE EXPRESSE QU ELLE SOIT ORALE OU CRITE DANS LA MESURE PERMISE PAR LA LOI MILWAUKEE RENONCE TOUTE GARANTIE IMPLICITE Y COMPRIS SANS S Y LIMITER TOUTE GARANTIE IMPLICITE DE QUALIT MARCHANDE OU D ADAPTATION UNE UTILISATION OU UNE FIN PARTICULI RE DANS LA MESURE OU UNE TELLE STIPULATION D EXON RATION N EST PAS PERMISE PAR LALOI LA DUR E DE CES GARANTIES IMPLICITES EST LIMIT E LA P RIODE APPLICABLE DE LA GARANTIE EXPRESSE TEL QUE D CRIT PR C DEMMENT CERTAINS TATS ET PROVINCES NE PERMETTANT PAS DE LIMITATION DE DUR E DES GARANTIES IM PLICITES LES RESTRICTIONS CIDESSUS PEUVENT NE PAS ETRE APPLICABLES LA PRESENTE CONFERE A L UTILISATEUR DES DROITS LEGAUX PARTICULIERS IL B N FICIE GALEMENT D AUTRES DROITS QUI VARIENT D UN ETAT A L AUTRE Cette garantie s applique aux produits vendus aux tats Unis et au Canada uniquement Veuillez consulter la rubrique Centre SAV MILWAUKEE dans la section Pieces amp Service du site Web de MILWAUKEE l adresse www milwaukeetool c
22. MS FOR LOSS OF PROFITS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IN CIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES WRITTEN OR ORAL TO THE EXTENT PERMITTED BY LAW MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR USE OR PURPOSE TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE This warranty applies to product sold in the U S A and Canada only Please consult the Service Center Search in the Parts amp Service section of MILWAUKEE s website www mil waukeetool com or call 1 800 SAWDUST 1 800 729 3878 to locate your nearest service facility for warranty and non warranty service on a Milwaukee electric power tool LIMITED WARRANTY MEXICO CENTRAL AMERICA AND CARIBBEAN TECHTRONIC INDUSTRIES warranty is for 5 year since the original purchase date This warranty card covers any defect in material and workmanship on this Power Tool To make this warranty valid present this warranty car
23. a posici n de en cendido contribuye a que se produzcan accidentes Quite todas las llaves de ajuste antes de en cender la herramienta Una llave que est acop lada a una pieza giratoria de la herramienta puede provocar lesiones personales No se estire demasiado Mantenga los pies bien asentados y el equilibrio en todo momento Esto permite tener mejor control de la herramienta el ctrica en situaciones inesperadas V stase de manera apropiada No lleve ropa suelta ni joyas Mantenga el cabello la ropa y los guantes lejos de la piezas en movimiento La ropa floja las joyas o el cabello largo pueden quedar atrapados en las piezas en movimiento Si se proporcionan dispositivos para la conex i n de sistemas de recolecci n y extracci n de polvo aseg rese de que est n conectados y se usen apropiadamente El uso de estos dispositivos puede reducir los peligros relacionados con el polvo USO Y CUIDADO DE LAS HERRAMIENTAS ELECTRICAS No fuerce la herramienta el ctrica Use la her ramienta el ctrica correcta para la aplicaci n La herramienta el ctrica correcta funcionar mejor y de manera m s segura a la velocidad para la que se dise No use la herramienta el ctrica si el interruptor no la enciende ni la apaga Cualquier herramienta el ctrica que no se pueda controlar con el interruptor es peligrosa y se debe reparar Desconecte el enchufe de la toma de aliment aci n y o la bater a de la herramienta el c
24. act in the opposite direction of the rotation of the bit Reduce the chances of a sudden reaction by following the instructions listed below Prepare for a sudden reaction by holding or bracing securely To reduce the chance of bit binding Use sharp bits Sharp bits are less likely to bind when drilling Use the proper bit for the job There are many types of bits designed for specific purposes Keep selfeed bits aligned with the work surface So bits go in straight see Drilling Avoid drilling warped wet knotty and or pitchy material if possible Avoid drilling in material that you suspect contains hidden nails or other things that may cause the bit to bind The direction of reaction is always opposite of the direction of bit rotation Reaction is even more likely to occur when enlarging already existing holes and at the point when the bit breaks through the other side of the material If the bit does bind 1 Release the trigger immediately 2 Reverse the motor 3 Remove the bit from the work and start again 4 Do not pull the trigger on and off to attempt to start a stalled bit This will damage the drill Bracing for forward rotation When drilling in forward the bit will rotate in a clockwise direction If the bit binds in the hole the bit will come to a sudden stop and drill will suddenly react in a counterclockwise direction The following figure shows an example of properly bracing the
25. ada el rea de trabajo Las reas desordenadas u oscuras con tribuyen a que se produzcan accidentes No utilice herramientas el ctricas en atm sferas explosivas como en la presencia de l quidos gases o polvo inflamables Las herramientas el ctricas crean chispas que pueden incendiar el polvo o las emanaciones Mantenga a los ni os y otras personas alejadas mientras utiliza una herramienta el ctrica Las distracciones pueden hacerle perder el control SEGURIDAD ELECTRICA Los enchufes de las herramientas el ctricas deben ser del mismo tipo que el tomacorrientes Nunca realice ning n tipo de modificaci n en el enchufe No use enchufes adaptadores con herramientas el ctricas con conexi n a tierra Se reducir el riesgo de descarga el ctrica si no se modifican los enchufes y los tomacorrientes son del mismo tipo Evite el contacto corporal con superficies con conexi n a tierra como tuber as radiadores es tufas y refrigeradores El riesgo de descarga el c trica aumenta si su cuerpo est conectado a tierra No exponga la herramientas el ctricas a la lluvia o a condiciones de humedad El agua que entra en una herramienta el ctrica aumenta el riesgo de descarga el ctrica No abuse del cable Nunca use el cable para transportar la herramienta el ctrica tirar de ella o desenchufarla Mantenga el cable alejado del calor los bordes afilados o las piezas en movimiento Los cables da ados o enmara ados au
26. ando use brocas de autoalimentacion re duzca la presion del taladro tan pronto como la punta del tornillo comience a entrar en la pieza de trabajo Prosiga aplicando presion firme y pareja MANTENIMIENTO ADVERTENCIA Para reducir el riesgo de una lesi n desconecte siempre la herramienta antes de darle cualquier man tenimiento Nunca desarme la herramienta ni trate de hacer modificaciones en el sistema el ctrico de la misma Acuda siempre a un Centro de Servicio MILWAUKEE para TODAS las reparaciones Mantenimiento de la herramienta Adopte un programa regular de mantenimiento y mantenga sus bater as y cargador en buenas condiciones Despues de 6 meses a un a o dependiendo del uso dado env e su herra mienta bater a y cargador al Centro de Servicio MILWAUKEE mas cercano para que le hagan Lubricaci n Inspecci n mec nica y limpieza engranes fle chas baleros carcaza etc Inspecci n el ctrica bater a cargador motor Probarla para asegurar una adecuada operaci n mec nicay el ctrica ACCESORIOS Para una lista completa de accessorios refi rase a su cat logo MILWAUKEE Electric Tool o visite nuestro sitio en Internet www milwaukeetool com Para obtener un cat logo contacte su distribuidor local o uno de los centros de servicio A ADVERTENCIA Para reducir el riesgo de lesiones siempre extraiga la bater a an tes de cambiar o retirar accesorios Util
27. as radios para obras del puerto de alimentaci n M12 Fuente de poder M18 y de las carretillas de trabajo industrial Trade Titan es de un 1 a o a partir de la fecha de compra El per odo de garant a de la l mpara de trabajo con diodo luminiscente y del foco mejorado con diodo luminiscente es una garant a VITALICIA limitada para el comprador original nicamente Si durante el uso normal el foco de diodo luminiscente no funciona la l mpara de trabajo o el foco mejorado se reemplazar sin carga Esta garant a no cubre las clavadoras a reas las engrapadoras el rociador de pintura inal mbrico el paquete de bater as inal mbrico los generadores el ctricos port tiles que funcionan con gasolina herramientas manuales elevadores el ctricos con palanca y con cadenas manuales camisas de calefacci n M12 productos reacondicionados y productos de prueba y medici n Se encuentran disponibles garant as distintas para estos productos No se necesita registro de garant a para obtener la garant a correspondiente de un producto el ctrico MILWAUKEE La fecha de fabricaci n del producto se utilizar para determinar el per odo de garant a si no se presenta un comprobante de compra en el momento en que se solicita el servicio de garant a LAACEPTACI N DE LOS DERECHOS A REPARACI N Y REEMPLAZO EXCLUSIVAMENTE DESCRITOS EN EL PRESENTE DOCUMENTO CONSTITUYE UNA CONDICI N DEL CONTRATO POR LACOMPRA DE CADA PRODUCTO MILWAUKEE SI NO ACEPTA
28. contacto con cableado oculto o con su propio cable sostenga las herramientas el ctricas de las superficies de empu adura aisladas El contacto del accesorio de corte con un cable que conduzca electricidad puede hacer que las partes met licas de la herramienta se electrifiquen y podr a ocasionar una descarga el ctrica al operador Guarde las etiquetas y placas de especifica ciones Estas tienen informaci n importante Si son ilegibles o si no se pueden encontrar p ngase en contacto con un centro de servicio de MILWAUKEE para una refacci n gratis ADVERTENCIA Algunas part culas de polvo resultantes del lijado mec nico aserrado esmer ilado taladrado y otras actividades relacionadas a la construcci n contienen sustancias qu micas que se saben ocasionan c ncer defectos cong nitos u otros da os al aparato reproductivo A continuaci n se citan algunos ejemplos de tales sustancias qu micas plomo proveniente de pinturas con base de plomo s lice cristalino proveniente de ladrillos cemento y otros productos de alba iler a y ars nico y cromo provenientes de madera qu micamente tratada El riesgo que usted sufre debido a la exposici n var a dependiendo de la frecuencia con la que usted realiza estas tareas Para reducir la exposici n a estas sustancias qu micas trabaje en un rea bien ventilada y utilice equipo de seguridad aprobado como por ejemplo m scaras contra
29. d sealed stamped by the distributor or store where you pur chased the product to the Authorized Service Center ASC Or if this card has not been sealed stamped present the original proof of purchase to the ASC Call toll free 1 800 832 1949 to find the nearest ASC for service parts accessories or components Procedure to make this warranty valid Take the product to the ASC along with the warranty card sealed stamped by the distributor or store where you pur chased the product and there any faulty piece or component will be replaced without cost for you We will cover all freight costs relative with this warranty process Exceptions This warranty is not valid in the following situations a When the product is used in a different manners from the end user guide or instruction manual b When the conditions of use are not normal c When the product was modified or repaired by people not authorized by TECHTRONIC INDUSTRIES Note If cord set is damaged it should be replaced by an Authorized Service Center to avoid electric risks SERVICE AND ATTENTION CENTER Model Av Presidente Mazarik 29 Piso 7 11570 Chapultepec Morales Miguel Hidalgo Distrito Federal Mexico Ph 52 55 4160 3547 IMPORTED AND COMMERCIALIZED BY TECHTRONIC INDUSTRIES MEXICO S A DE C V Av Presidente Mazarik 29 Piso 7 11570 Chapultepec Morales Miguel Hidalgo Distrito Federal Mexico Date of Purchase Distributor or Store Stam
30. de rotaci n de la broca Existen mayores probabilidades de que ocurra una reacci n cuando se alargan orificios ya existentes en el punto donde la broca entra al otro lado del material Si la broca se atora 1 Suelte el gatillo inmediatamente 2 Invierta la direcci n del motor 3 Extraiga la broca del material de trabajo y co mience nuevamente 4 No mueva el gatillo a las posiciones de activado y desactivado tratando de hacer arrancar una broca atorada Esto da ar la broca Apoyo para rotaci n en direcci n de avance Cuando se taladra en direcci n de avance la broca girar en el sentido de las manecillas del reloj Si se atora en el orificio la broca se detendr s bita mente y el taladro reaccionar repentinamente en sentido contrario a las manecillas del reloj Un ejemplo de un Hole Hawg que est apoyado correctamente para una reacci n hacia adelante A Rotaci n en direcci n de avance B Reacci n C Apoye el taladro con la caja de engranajes aqu Si se atora la broca la caja de engranajes apoyada contra la fijaci n sujetar el taladro en posici n Apoyo para rotaci n en direcci n de retroceso Cuando se taladra en direcci n de retroceso la broca girar en sentido contrario a las manecillas del reloj Si se atora en el orificio la broca se de tendr s bitamente y el taladro reaccionar repen tinamente en el sentido de las manecillas del reloj Un ejemplo de un Hole Hawg q
31. e for which it was designed Do notuse the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such pre ventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of chil dren and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions tak ing into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation BATTERY TOOL USE AND CARE Recharge only with the charger specified by the manufacturer A charger that
32. e peut tre ject de la batterie en cas de manutention abusive viter tout contact En cas de contact accidentel avec les projec tions rincer l eau En cas de contact avec les yeux consulter un m decin Le liquide s chappant de la batterie peut provoquer des irritations ou des br lures ENTRETIEN Faire effectuer l entretien de l outil lectrique par un technicien qualifi qui n utilisera que des pi ces de rechange identiques La s curit d utilisation de l outil en sera pr serv e REGLES DE S CURIT SP CIFIQUES Utiliser les poign e s auxiliaire s si elles sont fournie s avec l outil La perte de contr le peut causer des blessures Tenir les outils par ses surfaces de pr hension isol es lors des op rations pendant lesquelles l accessoire de coupe peut entrer en contact avec du c blage cach ou avec son propre cordon d alimentation Le contact d un accessoire de coupe avec un fil sous tension lectrifie les pi ces m talliques expos es de l outil et peut lectrocuter l utilisateur Entretenez les tiquettes et marqies di fabri cant Les indications qu elles contiennent sont pr cieuses Si elles deviennent illisibles ou se 9 d tachent faites les remplacer gratuitement un centre de service MILWAUKEE accr dit AVERTISSEMENT Certaines poussi res g n r es par les activit s de poncage de coupe de rectification de percage et d aut
33. el polvo que hayan sido espec ficamente dise adas para filtrar part culas microsc picas SIMBOLOGIA V Volts Corriente directa n xxxxmin PM clones por minuto sin carga c UL us DESCRIPCION FUNCIONAL Underwriters Laboratories Inc Estados Unidos y Canad Mango frontal Mandril de 13 mm Cat No 2707 20 LED Almacenamiento de llave Mango Interruptor Interruptor de control Mandril de 7 16 hexagonal Cat No 2708 20 D DADA RO 15 A ADVERTENCIA Recargue la bater a s lo con el cargador especificado para ella Para instrucciones espec ficas sobre c mo cargar lea el manual del operador suminis trado con su cargador y la bater a Como se inserta quita la bater a en la herramienta Para retirar la bater a presione los botones de liberaci n y jale de la bater a para sacarla de la herramienta Para introducir la bater a desl cela en el cuerpo de la herramienta Aseg rese de que quede bien firme en su posici n ADVERTENCIA Para reducir el riesgo de lesiones extraiga siempre la bater a antes de acoplar o desacoplar accesorios Utilice nicamente accesorios espec ficamente recomendados para esta herramienta El uso de accesorios no recomendados podr a resultar peligroso Selecci n de la broca
34. endo usado 17 A ADVERTENCIA A fin de reducir el riesgo de lesionarse mantenga las manos alejados de la broca y de todas las partes m viles Arranque paro y control de velocidad Estas herramientas pueden operarse a cualquier velocidad entre O y plena marcha 1 Para accionar la herramienta oprima el gatillo NOTA Las vueltas luz LED en cuando el dis parador se tira 2 Para variar la velocidad de operaci n simple mente aumente o disminuya la presi n del gatillo Cuanto m s se oprima el gatillo mayor ser la velocidad 3 Para detener la herramienta suelte el gatillo y elfreno el ctrico detendr la herramienta instan t neamente A ADVERTENCIA Para reducir el riesgo de explosion electrocuci n y da o a la propiedad antes de taladrar verifique siempre que en el rea de trabajo no hayan tuber as o cables ocultos Taladrado 1 Antes de taladrar cerciorese de que la pieza de trabajo este firmemente asegurada Una pieza de material no asegurada firmemente puede ocasionar lesiones personales o producir un taladrado sin precision Use material de refuerzo para evitar daiar la pieza de trabajo durante la operacion Al trabajar en madera o metal de menor calibre use un bloque de madera para 4 Reduzca la presi n durante la etapa final de la perforacion Mientras la herramienta contin a Operando tire de la broca hacia afuera del orificio para evitar que se atasque Cu
35. er acion donde la herramienta de corte puede hacer contacto con el cableado oculto Hacer contacto con un alambre energizado hara que las partes met licas expuestas de la herramienta tambi n est n energizadas y produzcan una descarga sobre el operador A ADVERTENCIA Para reducir el riesgo de lesiones personales sujete o apoye firme mente Siempre est preparado para un atora miento de la broca y la reacci n del taladro Atoramiento de broca Si se atora la broca el taladro reaccionar repentin amente en la direcci n opuesta de rotaci n de la br oca Reduzca las posibilidades de una reacci n re pentina siguiendo las instrucciones descritas a con tinuaci n Prep rese para una reacci n repentina sujetando o apoyando la herramienta firmemente Para reducir la posibilidad de atoramiento de la broca Use brocas afiladas Es menos probable que las brocas afiladas se atoren durante el taladrado Use la broca correcta para el trabajo Hay muchos tipos de brocas dise ados para fines espec ficos Mantenga las brocas de autoalimentaci n alin eadas con la superficie de trabajo para que entren en forma directa vea Taladrado Si es posible evite taladrar materiales pandeados h medos nudosos o resinosos Evite taladrar material que pueda tener clavos ocultos u otros objetos que puedan ocasionar el atoramiento de la broca La direcci n de rotaci n es siempre la opuesta a la direcci n
36. harge sp cifiques lire le manuel d utilisation fourni avec le chargeur et les batteries Insertion Retrait de la batterie Pour retirer la batterie enfoncer les boutons de d verrouillage et la tirer hors de l outil Pour ins rer la batterie la glisser dans le corps de l outil S assurer qu elle est fix e solidement AVERTISSEMENT taut toujours retirer la batterie et verrouiller la d tente de Poutil avant de changer ou d enlever les ac cessoires L emploi d accessoires autres que ceux qui sont express ment recommand s pour cet outil peut comporter des risques S lection de la m che Utilisez des m ches aiguis es Les m ches ai guis es risquent moins de se coincer pendant le percage Utilisez la m che qui convient la t che Plusieurs m ches sont concues pour des t ches particu li res V rifiez l information sur l emballage de la m che pour l utiliser correctement N utilisez pas des m ches plus grosses que la capacit nominale de la perceuse Sinon le moteur peut tre surcharg ou les engrenages endommag s voir Sp cifications Installation des embouts Toujours retirer la batterie avant d ins rer ou de retirer un embout Choisir un embout dont le type et la taille conviennent au type de vis utilis Installation des m ches dans les mandrins cl No de Cat 2707 20 1 Retirez la pile E 2 Ouvrez suffisamment les gt m choires du mandrin po
37. huck Center the bit in the chuck jaws and lift it about 1 16 off of the bottom Tighten the chuck jaws by hand to align the bit 4 Place the chuck key in each of the three holes in the chuck turning it clockwise to tighten the chuck securely NOTE Never use a wrench or means other than a chuck key to tighten or loosen the chuck 5 To remove the bit insert the chuck key into one of the holes in the chuck and turn it coun terclockwise Installing Bits into 7 16 Hex Chuck Cat No 2708 20 1 Remove the battery pack 2 To attach an accessory press the shank into the hex drive chuck 3 To remove the accessory pull out the ring and remove the accessory Release the ring WARNING Always remove battery pack before changing or removing acces sories Only use accessories specifically recommended for this tool Others may be hazardous A WARNING To reduce the risk of injury wear safety goggles or glasses with side shields WARNING To reduce the risk of per sonal injury when drilling hold the tool by isu lated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring Contact with a live wire will make exposed metal parts of the tool live and shock the operator A WARNING To reduce the risk of injury hold or brace securely Always be prepared for bit binding and drill reaction Bit binding If the bit binds the drill will suddenly re
38. ice nicamente accesorios espec ficamente recomendados para esta herramienta El uso de accesorios no recomendados podr a resultar peligroso GARANTIA LIMITADA E U A Y CANADA Se garantiza al comprador original que ninguna de las herramientas el ctricas MILWAUKEE incluido el producto inal mbrico la herramienta y as bater as consulte las declaraciones distintas y por separado en GARANT A LIMITADA DEL PAQUETE DE BATER AS INAL MBRICAS y de as luces de trabajo y del cargador de bater as presentan defectos en material ni en mano de obra En un plazo de cinco 5 a os a partir de la echa de compra y sujeto a ciertas excepciones MILWAUKEE reparar o reemplazar cualquier parte de una herramienta el ctrica que luego de ser examinada MILWAUKEE compruebe que presenta defectos en material o mano de obra a menos que se indique lo contrario Se requiere a devoluci n de la herramienta el ctrica a un centro de mantenimiento de la f brica MILWAUKEE o a un centro de reparaciones autorizado por MILWAUKEE con gastos de env o prepagados y asegurados La devoluci n del producto debe estar acompa ada por un comprobante de compra Esta garant a no se aplica a los da os que MILWAUKEE establece que fueron ocasionados por reparaciones o intentos de reparaci n por parte de personal no autorizado por MILWAUKEE uso indebido alteraciones abuso desgaste y deterioro normal falta de mantenimiento o accidentes El per odo de garant a de l
39. ile operating power tools may result in serious personal injury Use personal protective equipment Always wear eye protection Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewel lery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards POWER TOOL USE AND CARE Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rat
40. ilisation d un outil lectrique peut entrainer des blessures graves Porter l quipement de protection requis Tou conditions porter aussi un masque anti poussi res des bottes de s curit antid rapantes un casque protecteur ou une protection auditive afin de r duire les blessures Emp cher les d marrages accidentels S assurer que la g chette est en position d arr t avant de brancher l outil une source de courant d ins rer la batterie de le ramasser ou de le transporter Le fait de transporter l outil en gardant le doigt sur la g chette ou de le brancher lorsque la g chette est en position de marche favorise les accidents Retirer toute cl de r glage avant de mettre l outil sous tension Une cl laiss e attach e sur une pi ce mobile de l outil lectrique peut entrainer des blessures Ne pas travailler bout de bras Bien garder un bon quilibre tout instant Ceci permet de mieux pr server la ma trise de l outil lectrique dans des situations impr vues Porter des v tements ad quats Ne pas porter de v tements amples ni de bijoux Ne pas ap procher les cheveux v tements et gants des pieces en mouvement Les v tements amples les bijoux ou les cheveux longs risquent d tre happ s par les pi ces en mouvement Si des dispositifs sont pr vus pour l extraction et la r cup ration des poussi res v rifier qu ils sont connect s et utilis s correctement
41. mentan el riesgo de descarga el ctrica Cuando se utiliza una herramienta el ctrica en el exterior use una extensi n que sea apropiada para uso en el exterior El uso de un cable apro piado para el exterior reduce el riesgo de descarga el ctrica Si debe operar una herramienta el ctrica en un lugar h medo utilice un suministro protegido por un interruptor de circuito con conexi n a tierra GFCI Usar un GFCI reduce el riesgo de que se produzcan descargas el ctricas SEGURIDAD PERSONAL Mant ngase alerta ponga cuidado a lo que est haciendo y use el sentido com n cu ando utilice una herramienta el ctrica No use una herramienta el ctrica cuando est cansado o bajo la influencia de drogas al cohol o medicinas Despistarse un minuto cu ando se utiliza una herramienta el ctrica puede F tener como resultado lesiones personales graves Use un equipo de protecci n personal Lleve siempre protecci n ocular Llevar un equipo de protecci n apropiado para la situaci n como una m scara antipolvo zapatos de seguridad antidesli zantes un casco o protecci n auditiva reducir las lesiones personales Evite el encendido accidental Aseg rese de que el interruptor est en la posici n de apagado antes de conectarlo a la toma de alimentaci n o a la bater a al levantar o mover la herramienta Mover herramientas con el dedo en el interruptor o enchufarlas con el interruptor en l
42. n fonctionnement de l outil lectrique En cas de dommages faire r parer l outil avant de l utiliser de nouveau Les outils lectriques mal entretenus sont la source de nombreux accidents Garder les outils de coupe aff t s et propres Les outils de coupe correctement entretenus et bien aff t s risquent moins de se gripper et sont plus faciles manier Utiliser l outil lectrique les accessoires les grains etc conform ment ces instructions en tenant compte des conditions de travail et de la t che effectuer L utilisation de cet outil lectrique pour effectuer une op ration pour laquelle il n est pas concu peut occasionner une situation dangereuse UTILISATION ET ENTRETIEN DE LA BATTERIE Ne recharger la batterie qu avec le chargeur sp cifi par le fabricant Un chargeur qui con vient un type de batterie peut cr er un risque d incendie s il est utilis avec un autre type de batterie N utiliser les outils lectriques qu avec les batteries sp cialement concues pour eux L utilisation de batteries d autres marques peut cr er un risque de blessure et d incendie Lorsque la batterie est hors service la ranger l cart d autres objets m talliques tels que trombones pi ces de monnaie cl s clous vis et autres petits objets m talliques qui peuvent tablir une connexion d une borne l autre Un court circuit aux bornes de la batterie peut provoquer des br lures ou un incendie Du liquid
43. ns le guide de l utilisateur final ou le manuel d instructions b Si les conditions d utilisations ne sont pas habituelles C Si le produit a t modifi ou r par par une personne non autoris e par TECHTRONIC INDUSTRIES Note Si le cordon lectrique est endommag il doit tre remplac par un centre de r parations agr pour viter les risques d lectrocution CENTRE DE REPARATIONS ET DE SERVICE Av Presidente Mazarik 29 Piso 7 11570 Chapultepec Morales Miguel Hidalgo Distrito Federal Mexico Ph 52 55 4160 3547 IMPORTE ET COMMERCIALISE PAR TECHTRONIC INDUSTRIES MEXICO S A DE C V Av Presidente Mazarik 29 Piso 7 11570 Chapultepec Morales Miguel Hidalgo Distrito Federal Mexico 13 Mod le Date d achat Sceau du distributeur ou du magasin ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELECTRICA A ADVERTENCIA LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD Si no sigue todas las advertencias e instrucciones se pueden provocar una descarga el ctrica un incendio o lesiones graves Guarde todas las advertencias e instrucciones para consultarlas en el futuro El t rmino herramienta el ctrica en todas las advertencias incluidas m s abajo se refiere a su herramienta operada por conexi n cable a la red el ctrica o por medio de una bater a inal mbrica SEGURIDAD EN EL AREA DE TRABAJO Mantenga limpia y bien ilumin
44. ntation assorties r duisent le risque de choc lectrique Eviter tout contact corporel avec des surfaces reli es la masse ou laterre telles que tuyaux radiateurs cuisini res et r frig rateurs Un risque de choc lectrique plus lev existe si le corps est reli la masse ou la terre Ne pas exposer les outils lectriques la pluie ou l humidit Le risque de choc lectrique aug mente si de l eau s infiltre dans un outil lectrique Prendre soin du cordon Ne jamais utiliser le cordon pour transporter tirer ou d brancher l outil lectrique Tenir le cordon l cart de la chaleur des huiles des ar tes coupantes ou des pi ces en mouvement Un cordon endom mag ou emm l pr sente un risque accru de choc lectrique Se procurer un cordon d alimentation appro pri en cas d utilisation d un outil lectrique l ext rieur L utilisation d un cordon d alimentation pour usage ext rieur r duit le risque de choc lec trique S il est n cessaire d utiliser l outil lectrique dans un endroit humide installer un disjoncteur diff rentiel GFCI L utilisation d un GFCI r duit le risque de d charge lectrique S CURIT INDIVIDUELLE Etre sur ses gardes tre attentif et faire preuve de bon sens en utilisant un outil lectrique Ne pas utiliser un outil lectrique en cas de fatigue ou sous l influence de drogues d alcool ou de m dicaments Un instant d inattention lors de l ut
45. nte con el cargador especifi cado por el fabricante Un cargador que sea ap ropiado para un tipo de bater a puede crear riesgo de incendio cuando se use con otra bater a Use las herramientas el ctricas solamente con bater as espec ficamente disefiadas El uso de cualquier otro tipo de bater a puede crear riesgo de lesiones o incendio Cuando no se use la bater a mant ngala alejada de otros objetos de metal como clips para papel monedas llaves clavos tornillos u otros obje tos de metal pequefios que puedan realizar una conexi n entre los bornes Realizar un cortacir cuito en los terminales de la bater a puede provocar quemaduras o un incendio Bajo condiciones abusivas puede salir l quido expulsado de la bater a evitar el contacto Si se produce un contacto accidental lavar con agua Si el l quido entra en contacto con los ojos bus car ayuda m dica adicional El l quido que sale despedido de la bater a puede causar irritaciones o quemaduras MANTENIMIENTO Haga que un t cnico calificado realice el man tenimiento de la herramienta el ctrica utilizando solamente piezas de repuesto id nticas Esto asegurar que se mantiene la seguridad de la her ramienta el ctrica REGLAS ESPECIFICAS DE SEGURIDAD Use las empu aduras auxiliares si se propor cionan con la herramienta La p rdida de control puede causar lesiones personales Al realizar una operaci n donde el accesorio de corte pueda entrar en
46. ocked position Always lock the trigger or remove the battery pack before performing maintenance changing acces sories storing the tool and any time the tool is not in use A WARNING To reduce the risk of injury keep hands away from the bit and all moving parts Starting Stopping and Controlling Speed These tools may be operated at any speed from 0 to full speed 1 To start the tool pull the trigger NOTE An LED is turned on when the trigger is pulled 2 To vary the driving speed increase or decrease pressure on the trigger The further the trigger is pulled the greater the speed 3 To stop the tool release the trigger A WARNING To reduce the risk of explo sion electric shock and property damage always check the work area for hidden pipes and wires before drilling Drilling 1 Before drilling be sure the workpiece is clamped securely A poorly secured piece of material may result in personal injury or inaccurate drilling Use backing material to prevent damage to the workpiece during breakthrough When drilling in light gauge metal or wood use a wooden block to back up the material to prevent damage to the workpiece 2 When starting a hole place the drill bit on the work surface and apply firm pressure To start a selfeed bit run the threaded feed screw into the work by flicking the trigger switch permitting the bit to coast until the teeth contact the work surface Align the bit
47. om ou composer le 1 800 SAWDUST 1 800 729 3878 afin de trouver le centre de r parations en usine MILWAUKEE le plus pr s GARANTIE LIMITEE MEXIQUE AMERIQUE CENTRALE ET CARA BES TECHTRONIC INDUSTRIES garantit le produit pendant cing ans partir de la date d achat d origine Le pr sent bon de garantie couvre ous les vices de mat riau et de fabrication que peut afficher cet outil lectrique Pour assurer la validit de la pr sente garantie veuillez pr senter le bon de commande estampill du sceau du distributeur ou du magasin o le produit a t achet au centre de r parations agr Si le bon de commande n a pas t estampill veuillez fournir la preuve d achat d origine au centre de r parations agr Pour un entretien des pi ces des accessoires ou d autres composants composer sans frais le 1 800 832 1949 afin d obtenir les coordon n es du centre de r parations agr le plus pr s Proc dure pour assurer la validit de la garantie Pr senter le produit au centre de r parations agr accompagn du bon de commande estampill du sceau du distributeur ou du ma gasin o le produit a t achet Toute pi ce d fectueuse ou tout composant d fectueux sera remplac sans frais Milwaukee assume tous les frais de transport li s ce processus de garantie Exceptions La garantie ne s applique pas dans les situations suivantes a Si le produit a t utilis pour une fin autre que celle indiqu e da
48. ou Tirez le foret ou la m che hors du trou pendant que la perceuse tourne en core afin d viter un blocage Lorsque vous utilisez des m ches auto avance r duisez la pression de percage lorsque la pointe de la vis d avance passe au travers du mat riau Appliquez une pression r guli re et uniforme ENTRETIEN A AVERTISSEMENT Pour minimiser les risques de blessures corporelles d branchez le chargeur et retirez la batterie du chargeur ou de l outil avant d y effectuer des travaux d entretien Ne d montez jamais l outil la batterie ou le chargeur Pour toute r paration consultez un centre de service MILWAUKEE accr dit Entretien de l outil Gardez l outil la batterie et le chargeur en bon tat en adoptant un programme d entretien ponctuel Apr s une p riode de six mois un an Selon l utilisation renvoyez l outil la batterie et le chargeur un centre de service MILWAUKEE ac cr dit pour les services suivants Lubrification Inspection et nettoyage de la m canique engre nages pivots coussinets bo tier etc Inspection lectrique batterie chargeur moteur V rification du fonctionnement lectrom canique Si l outil ne d marre pas ou ne fonctionne pas pleine puissance alors qu il est branch sur une batterie compl tement charg e nettoyez les points de contact entre la batterie et l outil Si l outil ne fonctionne toujours pas correctement renvoyez l outil le chargeur et la batterie
49. ou d poser la batterie avant d effectuer un entretien de changer d accessoire de remiser l outil et toutes les fois que l outil est inutilis A AVERTISSEMENT Pour r duire les risques de blessures maintenez vos mains l cart du foret ou de la m che et de toutes les pieces mobiles D marrage arr t et contr le de vitesse Ces outils peuvent tre utilis s n importe quelle vitesse entre 0 et le plein r gime 1 Pour mettre l outil en marche appuyez sur la d tente N B LED allume quand la d tente est tir e 2 Pour varier la vitesse de rotation il s agit simple ment d augmenter ou de diminuer la pression sur la d tente Plus la d tente est enfonc e plus la vitesse de rotation est grande 3 Pour arr ter l outil rel chez la g chette A AVERTISSEMENT Pour r duire les risques d explosion de chocs lectriques et de dommages ala propri t v rifiez toujours que la zone de travail ne contient pas de tuyaux ou de cables cach s avant de com mencer a percer Percage 1 Avant de commencer percer assurez vous que la pi ce est fix e solidement Une pi ce mal fix e peut entrainer des blessures ou un percage incorrect Utilisez du mat riel de renfort pour viter d endommager la pi ce pendant qu elle est enta m e Lors du percage du bois ou du m tal de faible calibre utilisez des blocs de bois pour appuyer le mat riau et viter d endommager la pi ce 2 A
50. p 7 REGLES DE SECURITE GENERALES RELATIVES AUX OUTILS ELECTRIQUES AVERTISSEMENT LIRE TOUTES LES REGLES ET INSTRUCTIONS DE S CURIT Ne pas suivre l ensemble des r gles et instructions peut entra ner une lectrocution un incendie ou des blessures graves Conserver les regles et les instructions des fins de r f rence ult rieure Le terme outil lectrique figurant dans les avertissements ci dessous renvoie l outil lectrique alimentation par le r seau cordon ou par batterie sans fil SECURITE DU LIEU DE TRAVAIL Maintenir la zone de travail propre et bien clair e Les zones encombr es ou mal clair es sont favorables aux accidents Ne pas utiliser d outil lectrique dans une at mosphere explosive telle qu en en pr sence de liquides de gaz ou de poussi res inflammables Les outils lectriques g n rent des tincelles qui peuvent enflammer les poussi res ou les fum es Tenir les enfants et les personnes non au toris es l cart pendant le fonctionnement d un outil lectrique Un manque d attention de l op rateur risque de lui faire perdre le contr le de l outil S CURIT LECTRIQUE La fiche de l outil lectrique doit correspondre la prise d alimentation Ne jamais modifier la fiche d une mani re quelconque Ne pas utiliser d adaptateur avec les outils lectriques mis la terre la masse Des fiches non modifi es et des prises d alime
51. r la d tente de l outil avant de changer ou d enlever les ac cessoires L emploi d accessoires autres que ceux qui sont express ment recommand s pour cet outil peut comporter des risques A AVERTISSEMENT Pour minimiser les risques de blessures portez des lunettes a coques lat rales A AVERTISSEMENT Pour r duire les risques de blessures pendant le percage maintenez l outil par les surfaces de saisie isol es lorsque l outil de coupe peut entrer en contact avec des fils cach s Le contact d une partie m tallique de l outil avec un fil sous tension comporte un risque de choc lectrique A AVERTISSEMENT Pour r duire les risques de blessures maintenez ou soutenez de facon s curitaire Surveillez toujours que la m che ne se coince pas ou que l outil n ait pas de mouvement impr vu Coincement de la m che Sila m che se coince la perceuse r agit en inver sant subitement le sens de rotation de la m che R duisez les risques de r action soudaine en suivant les instructions ci dessous Soyez pr t r pondre une r action soudaine en maintenant ou en retenant de fa on s curitaire Pour r duire les risques de coincer la m che Utilisez des m ches aiguis es Les m ches ai guis es risquent moins de se coincer pendant le percage Utilisez la m che qui convient la t che Plusieurs m ches sont con ues pour des t ches particu li res Gardez les m ches
52. res acces Soires que ceux qui sont sp cifiquement recommand s pour cet outil peut comporter des risques GARANTIE LIMIT E AUX TATS UNIS ET AU CANADA Chaque outil lectrique MILWAUKEE y compris les produits sans fil outils piles chargeur de piles lampe de travail consulter les nonc s de la GARANTIE LIMIT E DES BLOCS PILES SANS FIL est garanti l acheteur d origine tre exempt de vice de mat riau et de fabrication Sous r serve de certaines exceptions MILWAUKEE r parera ou remplacera toute pi ce d un outil lectrique qui apr s examen par MILWAUKEE s est av r e tre affect e d un vice de mat riau ou de fabrication pendant une p riode de cinq 5 ans apr s a date d achat sauf indication contraire Retourner l outil lectrique un centre de r parations en usine MILWAUKEE ou un poste d entretien agr MILWAUKEE en port pr pay et assur Une copie de la preuve d achat doit tre pr sent e au moment de retourner e produit Cette garantie ne couvre pas les dommages que MILWAUKEE d termine tre caus s par des r parations ou des tentatives de r paration par quiconque autre que le personnel agr par MILWAUKEE des utilisations incorrectes des alt rations des utilisations abusives une usure normale une carence d entretien ou des accidents La p riode de garantie applicable pour les radios de chantier le port d alimentation M12 Source d nergie M18 et les chariots de travail ind
53. res activit s de construction contiennent des substances consid r es tre la cause de malformations cong nitales et de troubles de l appareil reproducteur Parmi ces substances figurent leplombcontenudansles peintures basede plomb la silice cristalline des briques du ciment et d autres mat riaux de maconnerie ainsi que l arsenic et le chrome des sciages trait s chimiquement Les risques encourus par l op rateur envers ces expositions varient en fonction de la fr quence de ce type de travail Pour r duire l exposition ces substances chimiques l op rateur doit travailler dans une zone bien ventil e et porter l quipement de s curit appropri tel qu un masque anti poussi re sp cialement con u pour filtrer les particules microscopiques V PICTOGRAPHIE Volts Tension CD seul ny XXXXmin Tours minute vide RPM U Underwriters Laboratories Inc CV LJUS tats Unis et Canada DESCRIPTION FONCTIONNELLE Poign e avant 2 Mandrin 13 mm No de Cat 2707 20 3 DEL Stockage de cl de mandrin Poign e d interrupteur Interrupteur de g chette Commutateur 8 Mandrin 7 16 Hexagonal No de Cat 2708 20 A ONO A AVERTISSEMENT Ne recharger la batterie qu avec le chargeur sp cifi Pour les instructions de c
54. s Keep children and bystanders away while operating a power tool Distractions can cause you to lose control ELECTRICAL SAFETY Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet condi tions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock elf operating a power tool in a damp location is unavoidable use a ground fault circuit inter rupter GFCI protected supply Use of an GFCI reduces the risk of electric shock PERSONAL SAFETY Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medi cation A moment of inattention wh
55. ssing contact a MILWAUKEE service facility for a free replacement WARNING Some dust created by power sanding SYMBOLOGY V Volts Direct Current n 1 No Load Revolutions NoXXXXMIN por Minute RPM Underwriters Laboratories Inc United States and Canada c UL us FUNCTIONAL DESCRIPTION 1 Top handle 2 1 2 Keyed chuck Cat No 2707 20 sawing grinding drilling and other construction 3 LED activities contains chemicals known to cause cancer birth defects or other reproductive harm Chuck koy Storage Some examples of these chemicals are 5 Main handle 8 lead from lead based paint 6 Trigger crystalline silica from bricks and cement and other masonry products and 7 Control switch arsenic and chromium from chemically treated 8 7 16 HEX chuck Cat No 2708 20 lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are spe cially designed to filter out microscopic particles SPECIFICATIONS Capacities Volts No Load Steel Wood Cat No DC RPM Twist Bit Ship Auger Bit Selfeed Bit Hole Saw 2707 20 18 0 1200 5 16 1 1 4 2 4 2708 20 18 0 1200 5 16 1 1 4 2 4
56. trica antes de realizar cualquier ajuste cambiar acce sorios o almacenar las herramientas el ctricas Dichas medidas preventivas de seguridad reducen el riesgo de que la herramienta se prenda acciden talmente Almacene las herramientas el ctricas fuera del alcance de los ni os y no permita que personas no familiarizadas con ellas o estas instrucciones las utilicen Las herramientas el ctricas son peligrosas en las manos de usuarios no capacitados Mantenimiento de las herramientas el ctricas Revise que no haya piezas m viles que est n desalineadas o que se atasquen piezas rotas ni ninguna otra condici n que pueda afectar el funcionamiento de la herramienta el ctrica Si se encuentran da os haga que le reparen la her ramienta antes de usarla Las herramientas mal mantenidas son la causa de muchos accidentes Mantenga las herramientas de corte limpias y afiladas Es menos probable que se atasquen las herramientas de corte con filos afilados que se mantienen de manera apropiada y tambi n son m s f ciles de controlar Use la herramienta el ctrica los acceso rios las brocas etc siguiendo estas instruc ciones teniendo en cuenta las condiciones de trabajo y la tarea que se va a realizar El uso de la herramienta el ctrica para op eraciones diferentes de aquellas para las que se dise podr a originar una situaci n peligrosa USO Y CUIDADO DE LAS HERRAMIENTAS CON BATER A Rec rguela solame
57. u d but du percage d un trou placez le foret ou la m che sur la surface de travail et appliquez une pression ferme Pour entamer avec une m che auto avance enfoncez la vis d avance filet e dans la pi ce en appuyant par petits coups sur l interrupteur de g chette afin de laisser la m che tourner par inertie jusqu ce qu elle entre en contact avec la surface de la pi ce Alignez correctement la m che avant de proc der Cette m thode permet de r duire le relevage et le blocage pendant le d marrage Lors du percage dans le m tal marquez le centre du trou percer avec un centrage au pointeau pour que la m che s engage plus facilement et sans trotter Lubrifiez la m che avec de l huile de coupe lors du percage dans le fer ou dans l acier Utilisez un fluide de refroidissement lors du percage de m taux non ferreux comme le cuivre le laiton ou l aluminium 3 Appliquez toujours la pression dans l alignement du foret ou de la m che Appliquez suffisamment de pression pour faire mordre la m che mais pas au point qu elle se coince Lorsque vous utilisez des forets ou des m ches h licoidales retirez les fr quemment pour enlever les copeaux des goujures Lorsque vous utilisez des m ches auto avance si l embrayage glisse retirez tr s l g rement la m che puis poussez la vers la pi ce R p tez plusieurs fois cette op ration 4 R duisez la pression et d gagez le foret ou la m che vers la fin du tr
58. ue est apoyado correctamente para una reacci n de retroceso A Rotaci n de retroceso hacia la izquierda B Reacci n C Apoye el taladro con la caja de engranajes del motor aqu Si se atora la broca la caja de engranajes apoyada contra la fijaci n sujetar el taladro en posici n Utilizaci n del interruptor de control El interruptor de control se puede colocar en tres posiciones diferentes avance retroceso y bajo seguro Debido a un mecanismo de traba el inter ruptor de control se puede cambiar de posici n nicamente cuando el interruptor de ENCENDIDO APAGADO no est presionado Para poder usar el interruptor de control siempre se debe esperar a que el motor se pare por completo Para avanzar el giro es en el sentido de las mane cillas del reloj se presiona el interruptor de control colocado al lado derecho del taladro Verificar la direcci n del giro antes de usarlo Para retroceder el giro es en el sentido opuesto a las manecillas del reloj se presiona el interruptor de control colocado al lado izquierdo del taladro Verificar la direcci n del giro antes de usarlo Para ponerle el seguro al gatillo el interruptor de control se coloca en la posici n central El gatillo no funcionara mientras el interruptor de control se encuentre bajo seguro en la posici n central Extraiga siempre la bater a antes cambiar acceso rios dar mantenimiento almacenar el taladro y siempre que ste no est si
59. ur y ins rer la m che Assurez vous que la queue de la m che et les m choires du mandrin sont propres Des particules de poussi re peuvent fausser l alignement de la m che 3 Ins rez la m che dans le mandrin Centrez la m che dans les m choires du mandrin et levez la environ 1 6 mm 1 16 du fond Serrez la main les m choires du mandrin pour aligner l embout 10 SPECIFICATIONS Capacit s Acier Bois Node Volts Tr min M che M che M che Cat CD vide h licoidale simple spirale auto avance Scie cloche 2707 20 18 0 1200 8mm 5 16 32 mm 1 1 4 51 mm 2 102 mm 4 2708 20 18 0 1200 8mm 5 16 32mm 1 1 4 51 mm 2 102 mm 4 MONTAGE DE L OUTIL 4 Placez la cl de mandrin dans chacun des trois trous du mandrin et tournez dans le sens horaire pour le fixer fermement N B Nutilisez pas de cl ou un autre outil que la cl de mandrin pour le serrer ou le desserrer 5 Pour enlever la m che ins rez la cl de mandrin dans un des trous du mandrin et tourner dans le sens antihoraire Installation des m ches dans les mandrins 7 16 Hexagonal No de Cat 2708 20 1 Retirez la pile 2 Pour attacher un accessoire enfoncer la queue dans le mandrin d entrainement hexagonal 3 Pour retirer l accessoire tirer l anneau et enlever l accessoire Rel cher l anneau MANIEMENT A AVERTISSEMENT I II faut toujours retirer la batterie et verrouille
60. ur une rotation arri re Si vous percez vers l arri re la m che tourne dans le sens antihoraire Si la m che se coince dans le trou elle s arr te soudainement et r agit en tour nant dans le sens horaire Un exemple d une foreuse Hole Hawg correcte ment tay e pour la rotation arri re A Rotation vers l avant sens horaire B R action C Etayez la foreuse en pla ant le bo tier du moteur ici Si la m che se coince le bo tier maintenus ferme ment contre le montant maintiendront la position de la m che Utilisation du commutateur Le commutateur peut tre r gl sur trois positions marche avant marche arri re et verrouill e En raison d un m canisme de verrouillage le commu tateur ne peut tre r gl que lorsque la commande MARCHE ARRET n est pas enfonc e Toujours laisser le moteur s arr ter compl tement avant d utiliser le commutateur Pour une rotation en marche avant dans le sens horaire pousser le commutateur sur le c t droit de l outil V rifier la direction de rotation avant utilisation Pour une rotation en marche arri re dans le sens anti horaire pousser le commutateur sur le c t gauche de l outil V rifier la direction de rotation avant utilisation Pour verrouiller la d tente pousser le com mutateur vers la position centrale La d tente ne fonctionne pas tant que le commutateur est sur la position verrouill e centrale Toujours verrouiller la d tente
61. ustriels Trade TitanTM est d une dur e d un 1 an partir de la date d achat La p riode de la garantie couvrant la lampe de travail DEL et l ampoule am lior e DEL est une garantie VIE limit e l acheteur d origine seulement si lors d une utilisation normale l ampoule DEL pr sente une d fectuosit la lampe de travail et l ampoule seront remplac es sans frais Cette garantie ne s applique pas aux cloueuses agrafeuses pneumatiques aux pulv risateurs peinture sans air aux blocs piles pour outils sans fil aux g n ratrices d alimentation portatives essence aux outils main aux monte charge lectrique levier et chaine manuel aux vestes chauffantes M12 aux produits r usin s ni aux produits d essai et de mesure Il existe des garanties distinctes pour ces produits L enregistrement de la garantie n est pas n cessaire pour b n ficier de la garantie en vigueur sur un outil lectrique MILWAUKEE La date de fabrication du produit servira tablir la p riode de garantie si aucune preuve d achat n est fournie lorsqu une demande de Service sous garantie est pr sent e L ACCEPTATION DES RECOURS EXCLUSIFS DE R PARATION ET DE REMPLACEMENT D CRITS AUX PR SENTES EST UNE CONDITION DU CONTRAT D ACHAT DE TOUT PRODUIT MILWAUKEE SI VOUS N ACCEPTEZ PAS CETTE CONDITION VOUS NE DEVEZ PAS ACHETER LE PRODUIT EN AUCUN CAS MILWAUKEE NE SAURAIT TRE RESPONSABLE DE TOUT DOMMAGE AC CESSOIRE SP CIAL OU INDIR
62. y sus accesorios Por favor llame al 01 800 8321949 para obtener los nombres y direcciones de los m s cercanos a usted o consulte la secci n D nde Comprar en nuestro sitio web www milwaukeetool com mx MILWAUKEE ELECTRIC TOOL CORPORATION 13135 West Lisbon Road Brookfield Wisconsin U S A 5 58 14 2717d1 05 14 eee in China 961016077 01 B

Download Pdf Manuals

image

Related Search

Related Contents

ReadyNAS for Home Software Manual  VGN-NW150J/S  Atemperador en línea tipo Venturi DVI de Fisherr  USER`S MANUAL AND INSTRUCTIONS  A100J V01-14  

Copyright © All rights reserved.
Failed to retrieve file