Home

Mercury 1999 Mountaineer Automobile User Manual

1. 28 Controls and features The EATC display window will indicate REAR FAN OFF The rear console fan will remain off until REAR FAN OFF is pressed again Operating tips In humid weather select DEF iV before driving This will prevent your windshield from fogging After a few minutes select any desired position To prevent humidity buildup inside the vehicle don t drive with the climate control system in the OFF position Don t put objects under the front seat that will interfere with the airflow to the back seats Remove any snow ice or leaves from the air intake area at the bottom of the windshield If your vehicle has been parked with the windows closed during hot weather the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open This will force most of the hot stale air out of the vehicle Then operate the air conditioner as you would normally When placing objects on top of your instrument panel be careful to not place them over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system 29 Controls and features Rear console climate controls if equipped Depending on the equipment
2. attached to a metal tag and is located on the driver side instrument panel For your protection you will also find the vehicle identification number in the following areas if applicable AIR Ww BAG XXXXXXXXXXXXXXXXX the left and right front fenders the left and right front doors the front and rear bumpers e the hood the left and right rear quarter panels e the decklid e the liftgate Gf equipped Engine number The engine number the last eight numbers of the vehicle identification number is stamped on the engine block transmission frame and transfer case if equipped 240 Reporting safety defects REPORTING SAFETY DEFECTS U S ONLY If you believe that your vehicle has a defect that could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 202 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation 400 Seventh Street Washington D C 20590
3. 5 4 5 6 7 8 9 0 3 Enter your personal 5 digit code Enter each digit within five seconds of the previous one Do not set a code that includes five of the same number or presents them in sequential order Thieves can easily figure out these types of codes Your personal code does not replace the permanent code that the dealership gave you You can use either code to unlock your vehicle If a second personal code is entered the module will erase the first personal code in favor of the new code 111 Controls and features If you wish to erase your personal code use the following instructions Erasing personal code 1 Enter the factory set code step 1 3 Press the 7 8 and 9 0 controls at 2 Press 1 2 within five seconds of J 4 5 6 7 8 9 0 the same time within five seconds of step two The system will now only respond to the factory set code Unlocking the doors with the keyless entry system To unlock the driver s door enter either the factory set code or personal code each digit pressed within 5 seconds of the prior digit The interior lamps will illuminate To unlock all doors enter the factory set code or personal code driver door unlocks and press the 3 4 control within 5 seconds 5 6 7 8 9 0 Locking the doors with the keyless entry system To lock all the doors press 7 8 and 9 0 at the same time It i
4. e We provide a Scheduled Maintenance Guide which makes tracking routine service easy If your vehicle requires professional service your dealership can provide necessary parts and service Check your Warranty Guide to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle e Do not work on a hot engine e When the engine is running make sure that loose clothing jewelry or long hair does not get caught up in moving parts e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation Keep all lit cigarettes open flames and other lit material away from the battery and all fuel related parts If you disconnect the battery the engine must relearn its idle conditions before your vehicle will drive properly as explained in Battery in this chapter Working with the engine off 1 Set the parking brake and ensure the gearshift is securely latched in P Park 2 Turn off the engine and remove the key 3 Block the wheels to prevent the vehicle from moving unexpectedly Working with the engine on 1 Set the parking brake and ensure the gearshift is securely latched in P Park
5. 35 Controls and features Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt Q to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly e Press p to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Seek function The seek function control works in radio mode Seek function in radio mode e Press lt to find the next listenable station down the frequency band e Press J gt to find the next listenable station up the frequency band Scan function The scan function works in radio mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 36 Controls and features Setting memory preset siations 1 Select the frequency band with the AM or the FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is
6. Always turn off the vehicle before fueling Automotive fuels can be harmful or fatal if swallowed Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury If fuel is swallowed call a physician immediately even if no symptoms are immediately apparent The toxic effects of fuel may not be visible for hours Avoid inhaling fuel vapors Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation In severe cases excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury 213 Maintenance and care e Avoid getting fuel liquid in your eyes If fuel is splashed in the eyes remove contact lenses if worn flush with water for 15 minutes and seek medical attention Failure to seek proper medical attention could lead to permanent injury e Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin and or clothing promptly remove contaminated clothing and wash skin thoroughly with soap and water Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation e Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact could cause an adverse reaction In sensitive individuals serious personal injury or sickness may result If fuel is splashed on the skin promptly wash skin thoroughly
7. If other than Ford Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Illumination of the charging system warning light Check Engine light or the temperature warning light fluid leaks strange odors smoke or loss of oil pressure could indicate that the emission control system is not working properly Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment 221 Maintenance and care Do not make any unauthorized changes to your vehicle or engine By law vehicle owners and anyone who manufactures repairs items sells leases trades vehicles or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working Information about your vehicle s emission system is on the Vehicle Emission Control Information Decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Please consult your Warranty Guide for complete emission warranty information Readiness for inspection maintenance I M testing
8. 000 3 Specification chart lubricants 235 Speed control 0 0 0 eeeeeeeeeeeeee 81 Speedometer cceeeeeseeeeeeees 12 Starting your vehicle 139 141 jump starting 183 184 186 Steering wheel ccccccceeeeees 86 HINE siressa 85 Tachometer cc cccccscccccesssseeeeees 13 TIVES sineme iene 209 210 Changing sess eieedivndigeaseesees 178 179 checking the pressure 210 replacing ae cevsgebvsnitecciewrsaseavecss 211 TOINA siner e eaa 210 snow tires and chains 212 Ure grades s 5d ncedscseascedeespesectrs 210 treadwear cccceesscesesteeseeseeees 209 TOWING 163 165 166 167 recreational towing 167 WEEGCK OP sec ctsescxecdcixstaccasviseddacnecs 189 Traction lok rear axle 160 Transfer case fluid CHECKING cesses sicdisatiareety 205 Transmission o s 146 203 automatic operation 146 fluid checking and adding automatic siiirieressissnss 203 204 Trip odometer sssansonsensoooeesse000e 13 Universal transmitter see garage door opener 92 93 94 95 96 Vehicle dimensions 06 238 Vehicle Identification Number CVILIND 55 casted csvencseaseiadtexessectaets tise 240 Vehicle loading c eee 160 Ventilating your vehicle 142 Warning Chimes isisssesisimsiiiss 6 Washer fluid cccccceceeeseeees 198 TESEYVOJI a 198 Water Driving through 162 Windows ou eeeeceeeece
9. Press the SCAN control to hear a short sampling of all selections on the tape The tape scans in a forward direction At the end of the tape s first side direction automatically reverses to the opposite side of the tape To stop on a particular selection press the control again Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again 64 Controls and features Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 Setting memory preset stations 1 Select the frequency band with 7 the AM FM select control gt WV 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset Rew FS TE N SFE control until the sound returns E indicating the station is held in memory on the control you selected gt Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations This feature is helpful on trips when you travel between cities with different radio stations Starting autoset memory preset 1 Select a frequency using
10. pt fA DRL Parai Larini Switch DTR oi a Memory Seat 29 10A Radio o y 30 15A Park Lamp Trailer Tow Relay st Not Used o 32 10A Heated Mirror Cd ee Module Instrument Cluster 34_ _ 7 5A___ Rear Integrated Control Panel CD 36 7 5A EATC Memory CD Rear Integrated Control Panel Memory Seat Message Center 174 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment The power distribution box contains high current fuses that protect your vehicle s main electrical systems from overloads A Always disconnect the battery before servicing high current fuses Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs 175 Roadside emergencies O Lr i Fal lenn O Fo ma D fo wM Goa Coe X oll ofp 0 Ee 2 Coe ca w E Da p o lm aam T O a xwe coy o fol m r gt I Si a ol ttt z g i J ea Le BS ed eo a EE NS J ij ij a 0 u A UD Ua The high current fuses are coded as follows Fuse Relay Fuse Amp Description Location Rating 1 I P Fuse Panel 2 Blower Motor Relay 3 50A 4 Wheel Anti Lock Brake System 4WABS Module Power Windows
11. For more information on engine coolant maintenance refer to Adding engine coolant in this chapter Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid Do not mix conventional green coolant orange coolant or recycled coolants together in your vehicle Use only the type of coolant that your vehicle was originally equipped with If you are unsure which type of coolant your vehicle requires contact your local dealer If sprayed on the windshield engine coolant could make it difficult to see through the windshield When the engine is cool add a 50 50 mixture of engine coolant and water to the engine coolant reservoir DO NOT ADD DIRECTLY TO THE RADIATOR Add straight water only in an emergency but you should replace it with a 50 50 mixture of coolant and distilled water as soon as possible 199 Maintenance and care Check the coolant level in the coolant reservoir the next few times you drive the vehicle If necessary add enough of a 50 50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir Never remove the coolant reservoir cap while the engine is running or hot If you must remove the coolant reservoir cap follow these steps to avoid personal injury 1 Before you remove the c
12. If the wiper blades do not wipe properly clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent Rinse thoroughly with clean water To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents Changing the wiper blades To replace the wiper blades 1 Pull the wiper arm away from the windshield and lock into the service O position z 2 Turn the blade at an angle from lt gt c the wiper arm Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm 3 Attach the new wiper to the wiper arm and press it into place until a click is heard 208 Maintenance and care INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade described below molded into the tire s sidewall These Tire Quality Grades are determined by standards that the United States Department of Transportation has set Tire Quality Grades apply to new pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575 104 c 2 U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford to give yo
13. In some localities it may be a legal requirement to pass an I M test of the on board diagnostic OBD II system If your Check Engine Service Engine Soon light is on refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter Your vehicle may not pass the I M test with the Check Engine Service Engine Soon light on If the vehicle s powertrain system or its battery has just been serviced the OBD II system is reset to a not ready for I M test condition To ready the OBD II system for I M testing a minimum of 30 minutes of city and highway driving is necessary as described below e First at least 10 minutes of driving on an expressway or highway e Next at least 20 minutes driving in stop and go city type traffic with at least four idle periods Allow the vehicle to sit for at least eight hours without starting the engine Then start the engine and complete the above driving cycle The engine must warm up to its normal operating temperature Once started do not turn off the engine until the above driving cycle is complete EXTERIOR BULBS Replacing exterior bulbs Check the operation of the following lamps frequently e Headlamps e Foglamps e High mount brakelamp e Brakelamps 222 Maintenance and care e Turn signals e License plate lamp e Tail lamps e Back up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones If a bulb is r
14. Power Moon Roof Power Seat Ignition Switch Starter Relay 6 20a Transfer Case Relay ee Notse o 20A Automatic Ride Control ARC Switch Off On Switch 9 40A Automatic Ride Control Relay 176 Roadside emergencies Location Rating 3 30A Heated Backlight 15A Fog Lamps and Daytime Running Lamps Not Used Powertrain Control Module gt es 30A 4 Wheel Anti Lock System 4WABS Module 15A A Rear Wiper Motor Fuel Pump Relay and RAP Module 10A 30A 15A 0A Horn Relay 15A 30A 15A 0A O 15A O Parklamps Relay and Mainlight Switch 30A O Mainlight Switch and Multifunction Switch Heated Oxygen Sensor EGR Vacuum Regulator EVR Solenoid Camshaft Position CMP Sensor Canister Vent Solenoid Generator Voltage Regulator jt 15 Not Used S OoOo o Wiper Park Relay A C Relay OOo o Wiper High Low Relay eee fl PCM Power Relay ae Fuel Pump Relay Starter Relay i y o7 orn Relay S Ee 8 Rear Wiper Down Relay 9 Blower Motor Relay 10 Rear Wiper Up Relay 1 Not Used 1 Not Used 2 Electronic Engine Controls Diode __ Mini Fuses Maxi Fuses 1 5 0L Engines Only 177 oe a 6 fe ae 5 E Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving do not apply the brake heavily Instead gradually decrease your speed Hold the steering wheel firmly and slowly move to a safe
15. To lock the liftgate and the liftgate window use the key or the power door locks depress the key lock cylinder or press the door lock switch on the left side of the cargo area 103 Controls and features The liftgate door and window should be closed before driving your vehicle If not possible damage may occur to the liftgate door lift cylinders and attaching hardware Make sure that the liftgate door and or window are closed to prevent exhaust fumes from being drawn into the vehicle This will also prevent passengers and cargo from falling out If you must drive with the liftgate door or window open keep the vents open so outside air comes into the vehicle CARGO COVER IF EQUIPPED Your vehicle may be equipped with a cargo area shade that covers the luggage compartment of your vehicle To install the shade 1 Fasten the cover into the mounting brackets make sure the cover is right side up 2 Pull the end of the shade toward you and hook the sides into the notches in the rear trim panels To prevent the possibility of injuries the fasteners for the cargo area cover must be properly attached to the mounting clips on the rear trim panels Do not place any objects on the cargo area cover They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision Rewinding the shade With extended use the cargo shade may lose its spring tension If this occurs
16. approximately eight seconds and release e Drive the vehicle slowly less than 5 km h 3 mph in circles until CAL indicator turns off in about 2 3 complete circles HOMELINK UNIVERSAL TRANSCEIVER WITH TRAVELNOTE IF EQUIPPED The HomeLink Universal Transceiver located on the driver s visor provides a convenient way to replace up to three hand held transmitters with a single built in device This feature will learn the radio frequency codes of most current transmitters to operate garage doors entry gates security systems entry door locks and home or office lighting When programming your HomeLink Universal Transceiver to a garage door or gate be sure that people and objects are out of the way to prevent potential harm or damage Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by U S federal safety standards this includes any garage door opener model manufactured before April 1 1982 A garage door which cannot detect an object signaling the door to stop and reverse does not meet current U S federal safety standards For more information on this matter call toll free 1 800 355 3515 or on the Internet at HomeLink jci com 92 Controls and features Programming 1 Prepare for programming the HomeLink Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light
17. begins to flash after 20 seconds Release both buttons 2 Hold the end of your hand held transmitter 5 14 cm 2 5 inches away from the HomeLink Universal Transceiver surface located on your visor while keeping the red light in view 3 Using both hands simultaneously press and hold the hand held transmitter button and the desired HomeLink button Do not release the buttons until step 4 has been completed 4 The red light will flash slowly and then rapidly Release both buttons when the red light flashes rapidly 5 Follow steps 2 through 4 to program the remaining two buttons If you do not successfully program the HomeLink Universal Transceiver after repeated attempts refer to Rolling code programing which follows or call toll free customer assistance 1 800 355 3515 or on the Internet at HomeLink jci com 93 Controls and features Canadian Programming During programming your hand held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transceiver To program your hand held transmitters e continue to hold the button on the HomeLink Universal Transceiver e press and re press the hand held transmitter button every two seconds until the red light changes from a slow to a fast flash Operating the HomeLink Universal Transceiver Once programmed the HomeLink Universal Transceiver can be used in place o
18. but not as economical Airflow will be from the instrument panel registers e Pe Vent Distributes outside air through the instrument panel registers However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode e OFF Outside air is shut out and the fan will not operate For short periods of time only use this mode to prevent undesirable odors from entering the vehicle 22 Controls and features 7 Panel and floor Distributes outside air through the instrument panel registers and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers e Floor Allows for maximum heating by distributing outside air through the floor ducts However the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode e H Floor and defrost Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will
19. leaving it misaligned or bent the sensing zone may be altered causing inaccurate measurement of obstacles 33 Controls and features To help avoid personal injury please read and understand the limitations on the reverse sensing system described above Reverse sensing is only an assist for some generally large and fixed objects It is the drivers responsibility for ensuring that their path is clear when operating the vehicle To help avoid personal injury always use caution when in reverse and when using the reverse sensing system USING YOUR AUDIO SYSTEM AM FM stereo cassette VOL PUSH ON OGE Dode ar ens 34 Controls and features Volume power control Press the control to turn the audio VOL PUSH ON system on or off Turn the control to raise or lower volume X x VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio and tape modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the AM control to select from AM selections and press the FM control to select from FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play
20. running engine may cause internal damage Cleaning the wheels Wash with the same detergent as the body of your vehicle Do not use acid based or alcohol based wheel cleaners steel wool fuel or strong detergents Never use abrasives that will damage the finish of special wheel surfaces Use a tar remover to remove grease and tar 229 Maintenance and care Underbody Flush the complete underside of vehicle frequently Keep body drain holes unplugged Inspect for road damage Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning Clean with a tar remover if necessary Do not clean plastic parts with thinners solvents or petroleum based cleaners Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle Use glass cleaner or tar remover if necessary To avoid scratching the lamps do not use a dry paper towel chemical solvents or abrasive cleaners Cleaning the wiper blades and windshield If the wiper blades do not wipe properly clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent To avoid damaging the blades do not use fuel kerosene paint thinner or other solvents If the wiper still does not wipe properly this could be caused by substances on the windshield such as tree sap and some hot wax treatments used by commercial car washes Clean the outside of the windshield with a non abrasive cleanser such as the non abrasive
21. the engine so the heater can be plugged in the night before starting the vehicle To prevent electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapters 141 Starting Guarding against exhaust fumes Although odorless and colorless carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects If you ever smell exhaust fumes of any kind inside your vehicle have your dealer inspect and fix your vehicle immediately Do not drive if you smell exhaust fumes These fumes are harmful and could kill you Have the exhaust and body ventilation systems checked whenever e the vehicle is raised for service e the sound of the exhaust system changes e the vehicle has been damaged in a collision Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time open the windows at least 2 5 cm one inch Adjust the heating or air conditioning if equipped to bring in fresh air Improve vehicle ventilation by keeping all air inlet vents clear of snow leaves and other debris 142 Driving BRAKES Your service brakes are self adjusting Refer to the maintenance guide and or service guide for
22. tongue weight capability Use a frame mounted weight distributing hitch for trailers over 1 590 kg 3 500 Ib Driving while you tow Do not drive faster than 88 km h 55 mph when towing a trailer Speed control may shut off if you are towing on long steep grades When towing a trailer e Use a lower gear when towing up or down steep hills This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling e Anticipate stops and brake gradually Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent service intervals Refer to your Scheduled Maintenance guide for more information Trailer towing tips e Practice turning stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination When turning make wider turns so the trailer wheels will clear curbs and other obstacles e Allow more distance for stopping with a trailer attached The trailer tongue weight should be 10 of the loaded trailer weight 166 Driving e After you have traveled 80 km 50 miles thoroughly check your hitch electrical connections and trailer wheel lug nuts e When stopped in traffic for long periods of time in hot weather place the gearshift in P Park and increase idle speed This aids engine cooling and
23. 2 Block the wheels to prevent the vehicle from moving unexpectedly 191 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running OPENING THE HOOD 1 Inside the vehicle pull the hood release handle located under the steering column on the instrument panel 192 Maintenance and care 2 Go to the front of the vehicle and release the auxiliary latch that is located in the center between the hood and the grill 3 Lift the hood until the lift cylinders hold it open IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4 0L SOHC V6 engine ANI 4 O AY MAEA Windshield washer fluid reservoir Automatic transmission fluid dipstick Engine oil filler cap Engine oil dipstick Brake fluid reservoir Battery Power steering fluid reservoir Air filter assembly POA AAR WN H Engine coolant reservoir 193 Maintenance and care 5 0L V8 engine Engine coolant reservoir 1 2 3 4 5 6 7 8 9 Windshield washer fluid reservoir Engine oil filler cap Automatic transmission fluid dipstick Brake fluid reservoir Battery Power steering fluid reservoir Engine oil dipstick Air filter assembly ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil 1
24. 500 SAN 4 0L 4 535 0 2 540 SOHC 10 000 0 5 600 KO 4 990 0 2 921 1 000 0 6 440 AUEI Notes For high altitude operation reduce GCW by 2 per 300 meters 1 000 ft elevation For definition of terms and instructions on calculating your vehicle s load refer to Vehicle loading in this chapter Maximum trailer weights shown The combined weight of the completed towing vehicle and the loaded trailer must not exceed the GCWR Towing a trailer over 1 588kg 8 500 lbs requires a weight distributing hitch Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage transmission damage structural damage loss of control and personal injury 164 Driving Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle See your dealer or a reliable trailer dealer if you require assistance Hitches Do not use hitches that clamp onto the vehicle bumper Use a load carrying hitch You must distribute the load in your trailer so that 10 of the total weight of the trailer is on the tongue Use a frame mounted weight distributing hitch for trailers over 1 588 kg 3 500 Ib Safety chains Always connect the trailer s safety chains to the vehicle To connect the trailer s safety chains cross the c
25. 75 Controls and features e In CD mode if equipped use the SEEK function to access the next or previous lt lt selection CD changer if equipped The CD changer is located in one of the following locations e in the trunk e in the center console e under the driver s seat 1 Slide the door to access the CD changer magazine 2 Press amp to eject the magazine 3 Turn the magazine A over 4 Using the disc holder release knob C pull the disc holder B out of the magazine 76 Controls and features If you pull too hard on the disc holder the disc holder may come completely out of the magazine If this happens reinsert the disc holder back into the magazine while pressing on the lever A 5 Line up the CD with the groove of the disc holder Ensure that the label on the CD faces downwards 6 Press in on the disc holder until it locks securely into the magazine If the disc holders are not fully locked into the magazine the unit will not operate Ensure that the disc holder is evenly inserted and at the same level as the magazine A The unit will not operate if the disc holder is not inserted at the same level B Radio power must be turned on to play the CDs in the changer The magazine may be stored in the glove box when not being used 77 Controls and features The CD magazine may be inserted or ejected with the radio power off ONLY use the magazine supplied with
26. Bon Ami powder Rinse thoroughly with clean water Do not use abrasive cleansers on glass as they may cause scratches The windshield is clean if beads do not form when you rinse it with water The windshield and wiper blades should be cleaned on a regular basis and blades or rubber elements replaced when worn Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Follow the directions that come with the cleaner Do not saturate the seat cover with upholstery cleaner Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag Such products could contaminate the side air bag system and affect performance of the side air bag in a collision 230 Maintenance and care Cleaning the instrument panel Clean with a damp cloth then dry with a dry cloth Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel The dull finish in this area helps protect the driver from undesirable windshield reflection Cleaning the overhead console Clean with a damp cloth then wipe dry with a dry cloth Avoid cleaner or polish that increases the gloss of the console The dull finish in this area helps protect the driver from undesirable windshield reflection Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner Remove fresh spots immediately Do no
27. Refer to Automatic locking mode passenger side front and outboard rear seating positions if equipped Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat in a seating position which is capable of providing a tether anchorage For more information on top tether straps refer to Attaching safety seats with tether straps Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision 134 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1 Position the child safety seat in a seat with a combination lap and shoulder belt An air bag can kill or injure a child in a child seat If you must use a forward facing child seat in the front seat move seat all the way back Children 12 and under should be properly restrained in the rear seat whenever possible 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 135 Seating and safety restraints 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted 4 Insert the belt tongue into the proper buckle th
28. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations 161 Driving The Certification Label found on the inside pillar of the driver s door lists several important vehicle weight rating limitations Before adding any additional equipment refer to these limitations If you are adding weight to the front of your vehicle potentially including weight added to the cab the weight added should not exceed the Front Axle Reserve Capacity FARC Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways i e restrict the number of passengers or amount of cargo carried You may add equipment throughout your vehicle if the total weight added is equal to or less than the Total Axle Reserve Capacity TARC weight You should NEVER exceed the Total Axle Reserve Capacity Always ensure that the weight of passengers cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both Gross Vehicle Weight and Front and Rear Gross Axle Weight Rating limits Under no circumstance should these limitations be exceeded Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and or personal injury Calculating the load your vehicle can carry tow 1 Use the appropriate maximum gross combined weight rating CWR chart to find the maximum GCWR for you
29. V6 engine 4x2 5R55E 9 8L Automatic with 10 3 quarts 4 0L SOHC V6 engine 4x4 Transfer case Motorcraft AWD 1 25L MERCON ATF 1 3 quarts 4WD 1 4L 1 5 quarts Engine coolant See footnote 4 0L SOHC V6 13 2L engine 14 0 quarts 5 0L V8 engine 14 9L 15 7 quarts Front axle fluid Motorcraft 4x4 vehicles LTL 80W90 Axle F Lubricant 1 8 quarts Rear axle Motorcraft SAE Refer to lubricant 80W90 Premium footnote 3 Rear Axle Lubricant Motorcraft SAE Refer to ea pints 75W140 High footnote 4 Performance Synthetic Rear Axle Lubricant Windshield Ultra Clear All vehicles washer fluid Windshield 2 6L Washer 2 7 quarts Concentrate 234 Capacities and specifications 1 If your engine coolant is green in color use Ford Premium Cooling System Fluid If your coolant is orange in color use Ford Extended Life Engine Coolant Refer to Adding engine coolant in the Maintenance and Care chapter 2 Fill to 6 mm to 14 mm 1 4 inch to 9 16 inch below bottom of fill hole 3 Vehicles equipped with a 4 0L SOHC V6 engine may be equipped with a conventional rear axle Refer to your Scheduled Maintenance Guide for axle fluid change intervals 4 Vehicles equipped with 4 0L SOHC V6 engine and 3 73 1 or 4 10 1 rear axle ratios or with a 5 0L V8 engine require synthetic rear axle lubricant Rear axles containing synthetic lubricant are lubricated for life These lubricants are not to be checked or changed unless a leak is
30. air conditioner efficiency e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels Launching or retrieving a boat When backing down a ramp during boat launching or retrieval e Do not allow the static water level to rise above the bottom edge of the rear bumper and e Do not allow waves to break higher than 15 cm six inches above the bottom edge of the rear bumper Exceeding these limits may allow water to enter critical vehicle components adversely affecting driveability emissions reliability and causing internal transmission damage Replace the rear axle lubricant anytime the axle has been submerged in water Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required Disconnect the wiring to the trailer before backing the trailer into the water Reconnect the wiring to the trailer after the trailer is removed from the water Recreational towing all wheels on the ground Do not tow your vehicle with all wheels on the ground as vehicle damage may occur LUGGAGE RACK Maximum load is 75 kg 165 lbs evenly distributed If it is not possible to distribute the load position it as far rearward as possible Adjustable tie down loops not equipped must be used to secure the load 167 Driving To adjust cross bar position 1 Slide the locking switches at each end of the crossbar toward the r
31. as dry road surfaces wet pavement snow and gravel e The 4WD HIGH mode provides four wheel drive with full power to both axles It is only intended for severe winter or off road conditions such as deep snow and ice where no dry or wet pavement remains uncovered and shallow sand The 4WD LOW mode supplies four wheel drive with full power to both axles and includes a lower gear ratio for low speed It is only intended for off road applications that require extra power including deep sand steep grades and pulling a boat and trailer out of the water The vehicle should not be operated in 4WD HIGH and 4WD LOW on dry or merely wet pavement Doing so will produce excessive noise increase tire wear and may damage driveline components These modes are intended for use only on consistently slippery or loose surfaces 153 Driving If your vehicle is equipped with 4WD or AWD a spare tire of a different size than the road tires should never be used Such a tire could result in damage to driveline components and make the vehicle difficult to control Utility and four wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low slung sports cars are designed to perform satisfactorily under off road conditions Avoid sharp turns or abrupt maneuvers in these vehicles Using the Control Trac system Shifting between 4WD AUTO and 4WD HIGH When you move the control to 4WD HIGH the
32. assembly until the plastic base contacts the rear of the lamp assembly 2 Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating clockwise until you feel a stop 3 Install the electrical connector into the rear of the plastic base until it snaps locking it into position 4 Turn the headlamps on and make sure they work properly If the headlamp was correctly aligned before you changed the bulb you should not need to align it again Replacing front parking lamp turn signal bulbs 1 Remove screw from the lamp assembly 2 Disengage lamp assembly 224 Maintenance and care 1 Rotate bulb socket counterclockwise about 1 4 turn and remove from lamp assembly 2 Carefully pull bulb straight out of socket and push in the new bulb 3 Install bulb socket in lamp assembly by turning clockwise 4 Align the parking lamp assembly and push to snap in place 5 Install screw on lamp assembly Replacing tail lamp backup lamp bulbs The tail lamp backup lamp bulbs are located in the same portion of the tail lamp assembly one just below the other Follow the same steps to replace either bulb 1 Open the liftgate to expose the lamp assemblies 7 2 Remove the two screws from the lamp assembly 3 Carefully remove the lamp assembly by pulling it rearward 4 Twist the bulb socket 1 4 turn counterclockwise and remove from lamp assembly 5
33. be slightly warmer than the air sent to the instrument panel registers For added customer comfort when the temperature control knob is anywhere in between the full hot and full cold positions the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to prevent fogging e GH Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to prevent fogging Operating tips e In humid weather select V7 before driving This will prevent your windshield from fogging After a few minutes select any desired position e To prevent humidity buildup inside the vehicle don t drive with the climate control system in the OFF position e Don t put objects under the front seat that will interfere with the airflow to the back seats 23 Controls and features Remove any snow ice or leaves from the air intake area at the bottom of the windshield under the hood If your vehicle has been parked with the windows closed during hot weather the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open This will force most of the hot stale air o
34. been established it will be used beginning with the completion of your next OIL CHANGE RESET procedure 19 Controls and features HEADLAMP CONTROL Rotate the headlamp control to the is first position to turn on the parking w lamps Rotate to the second position Oe X to also turn on the headlamps Foglamp control if equipped Turn on the low beam headlamps and press the foglamp control to activate the foglamps The foglamp control will illuminate when the foglamps are on _ f Press the foglamp control a second time to deactivate the foglamps Daytime running lamps DRL if equipped Turns the headlamps on with a reduced output To activate e the engine must be running and e the headlamp control is in the OFF or Parking lamps position Always remember to turn on your headlamps at dusk or during inclement weather The Daytime Running Light DRL System does not activate your tail lamps and generally may not provide adequate lighting during these conditions Failure to activate your headlamps under these conditions may result in a collision High beams Push forward to activate 4 20 Flash to pass Pull toward you to activate and release to deactivate PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation e Rotate up to brighten e Rotate down to dim e Rotate to full down position to turn off CLIMATE CONTROL SYSTEM Controls a
35. control Press the MODE control to change audio sources for headphone mode only Use the SEEK VOLUME and MEMORY controls to make adjustments to the playing media Adjusting the volume Press the control to increase volume Press the control to decrease volume From the rear seat controls volume control can be set no higher than the current radio setting unless the speakers are turned off Refer to Turning speakers on and off 58 a MODE C JCJ goano 0 VOLUME MODE SIAN lt a SEEK gt MEMORY Canes E gt Oo ia BE UEA MODE lt q SEEK B MEMORY C _ D0 DORO Controls and features Turning the speakers on and off Press to turn all speakers on or off VOLUME MODE ee NE lt q SEEK B MEMORY C J0 gt Oo Using headphones Plug a 3 5 mm headphone not included into the A jack Press the speaker on off control to operate the headphones The rear speakers will cut out once the speaker on off control is pressed The front speaker will remain playing for the front passengers Press the control again to deactivate the headphones Mode select Push the MODE control to toggle CH between AM FM1 FM2 tape CD or VOLUME MODE CD changer if equipped C q lt q SEEK B MEMORY 2 LS ano IO 7 59 Controls and features Memory preset control Push the MEMORY control successively to allow
36. control to lock all doors To confirm all doors are closed and locked press the control a second time within five seconds The doors will lock again the horn will chirp and the lamps will flash If any of the doors are ajar the horn will make two quick chirps reminding you to properly close all doors Sounding a panic alarm Press this control to activate the alarm To deactivate the alarm press the control again or turn the ignition to ACC or ON This device complies with part 15 of the FCC rules and with RS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 106 Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Memory seat feature if equipped The remote entry system can also control the memory seat feature Press the control once to unlock the driver s door and move the memory seat feature to the corresponding memory position just as if you had pressed the memory control in the vehicle When your dealer programs new transmitters e the first transmitter programmed will recall memory position one e the second transmitter programmed will recall memory position two e the t
37. held in memory on the control you selected VVW Bass adjust The bass adjust control allows you N to increase or decrease the audio A system s bass output BASS Y Treble adjust The treble adjust control allows you N to increase or decrease the audio A system s treble output TREB 37 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Tape select e To enter tape mode while in radio mode press the TAPE AMS control Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection 38 as A BAL as Controls and features To activate the feature momentarily depress the TAPE AMS button Then press either REW for the beginning of the current selection or FF to advance to the next selection The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape In order to ensure proper operation of the AMS feature the tape MUST have a blank section of at least 4 seconds duration between programs Rewind The rewind control works in tape mode To rewind in tape mode press the REW control Radio play will continue until rewind is stopped with the FF cont
38. illuminate briefly If a light fails to illuminate have the vehicle serviced e If the driver s safety belt is fastened the A light will not illuminate 140 Starting STARTING THE ENGINE 1 Turn the key to 5 START lt without pressing the accelerator 4 X 5 pedal and release as soon as the engine starts The key will return to 4 ON oP 2 2 If the temperature is above 12 C 10 F and the engine does not start within five seconds on the first try turn the key to OFF wait ten seconds and try again 3 If the temperature is below 12 C 10 F and the engine does not start in fifteen seconds on the first try turn the key OFF and wait ten seconds and try again If the engine does not start in two attempts depress the accelerator and start the engine while holding the accelerator down to the floor Release the accelerator when the engine starts 4 After idling for a few seconds apply the brake and release the parking brake Using the engine block heater if equipped An engine block heater warms the engine coolant which improves starting warms up the engine faster and allows the heater defroster system to respond quickly Use of an engine block heater is strongly recommended if you live in a region where temperatures reach 23 C 10 F or below For best results plug the heater in at least three hours before starting the vehicle Using the heater for longer than three hours will not harm
39. in the Maintenance and Care chapter 2 Ensure correct automatic transmission fluid is used for a specific application Check the container to verify the fluid is MERCON and or MERCON V approved Some fluids have been approved as meeting both MERCON and MERCON V requirements and will be labeled as such Fluids labeled as meeting only MERCON or only MERCON V requirements must not be used interchangeably DO NOT mix MERCON and MERCON V Transmission fluid requirements are indicated on the dipstick or on the dipstick handle Refer to your Scheduled Maintenance Guide to determine the correct service interval 248
40. indicator light will illuminate in the instrument cluster When you move the control to 4WD AUTO the indicator light will turn off Either shift can be done at a stop or N while driving at any speed Shifting from 4WD AUTO or 4WD HIGH to 4WD LOW 1 Bring the vehicle to a stop 2 Depress the brake 3 Place the gearshift in N Neutral 4 Move the 4WD control to the 4WD LOW position 154 Driving Shifting from 4WD LOW to 4WD AUTO or 4WD HIGH 1 Bring the vehicle to a stop e 2 Depress the brake 3 Place the gearshift in N Neutral 4 Move the 4WD control to the 4WD AUTO or 4WD HIGH position a Q Driving off road with 4WD Your vehicle is specially equipped for driving on sand snow mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles both on and off the road Maintain steering wheel control at all times especially in rough terrain Since sudden changes in terrain can result in abrupt steering wheel motion make sure you grip the steering wheel from the outside Do not grip the spokes Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps You should either know the terrain or examine maps of the area before driving Map out your route before driving in the area For more information on driving off road read the Four Wheeling supplement in your owner s portfolio If your vehicle gets stu
41. injure you or others 216 Maintenance and care If you do not use the proper fuel filler cap the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision Fuel Filter Your vehicle is equipped with a fuel filter that is mounted on the underbody For fuel filter replacement see your dealer or a qualified service technician Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter If you replace the fuel filter replace it with an authorized Motorcraft part The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you the driver You must gather information as accurately and consistently as possible Fuel expense frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy We do not recommend taking fuel economy measurements during the first 1 600 km 1 000 miles of driving engine break in period You will get a more accurate measurement after 3 000 km 5 000 km 2 000 miles 3 000 miles The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities chart in this Owner Guide The advertised capacity is the amount of the Indicated Capacity
42. inspected by a qualified service technician The ABS operates by detecting the onset of wheel lockup during brake applications and compensating for this tendency The wheels are prevented from locking even when the brakes are firmly applied The accompanying illustration depicts the advantage of an ABS equipped vehicle on bottom to a non ABS equipped vehicle on top during hard braking with loss of front braking traction 143 Driving ABS warning lamp The s warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off If the light does not illuminate momentarily at start up remains on or continues to flash the ABS needs to be serviced With the ABS light on the anti lock brake system is disabled and normal O braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released If your brake warning lamp illuminates have your vehicle serviced immediately Using ABS e In an emergency or when maximum efficiency from the ABS is required apply continuous full force on the brake The ABS will be activated immediately thus allowing you to retain full steering control of your vehicle and providing there is sufficient space will enable you to avoid obstacles and bring the vehicle to a controlled stop e The Anti Lock system does not decrease the time necessary to apply the brakes or always reduce stopping dist
43. more impact and safing sensors e a readiness light and tone 128 Seating and safety restraints e and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning including the impact sensors the system wiring the air bag system readiness light the air bag back up power and the air bag ignitors Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system Refer to the Air bag readiness section in the Instrumentation chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness light will either O O flash or stay lit r e The readiness light will not IN illuminate immediately after ignition is turned on e A series of five beeps will be heard The tone pattern will repeat periodically until the problem and light are repaired If any of these things happen even intermittently have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision Side air bag system if equipped Do not use accessory seat covers The use of accessory seat covers may prevent the deployment of the side air bags and increase the risk of injury in an accident Do no
44. occupants in side impact collisions The air bag SRS is designed to activate when the vehicle sustains sufficient lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Side air bags are designed to inflate in side impact collisions not roll over rear impact frontal or 130 Seating and safety restraints near frontal collisions unless the collision causes sufficient lateral deceleration Several air bag system components get hot after inflation Do not touch them after inflation If the side air bag has deployed the air bag will not function again The side air bag system including the seat must be inspected and serviced by a qualified technician in accordance with the vehicle service manual If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system Refer to the Air bag readiness section in the Instrumentation chapter Routine maintenance of the air bag is not required A difficulty with the system is indicated by one or more of the following e The readiness light will ei
45. offset changes in vehicle loads When ever a door is opened including the liftgate the system memorizes and maintains the height of the vehicle until all doors are closed It is normal to hear a buzz or clicking from the air compressor on the vehicle when the ignition is turned off The system stays energized for 40 minutes after the ignition is turned off to compensate for any load changes made after the vehicle is parked 145 Driving The air suspension shut off switch is located in the cargo area behind the left rear quarter trim panel On vehicles equipped with Air Suspension turn OFF the Air Suspension switch prior to jacking hoisting or towing your vehicle Normal vehicle operation does not require any action by the driver TRANSMISSION OPERATION Automatic transmission operation Brake shift interlock This vehicle is equipped with a brake shift interlock feature that prevents the gearshift from being moved from P Park unless the brake pedal is depressed If you cannot move the gearshift out of P Park with the brake pedal depressed 1 Apply the parking brake turn ignition key to LOCK then remove the key 2 Insert the key and turn it to OFF Apply the brake pedal and shift to N Neutral 3 Start the vehicle If it is necessary to use the above procedure to move the gearshift it is possible that a fuse has blown or the vehicle s brakelamps are not operating properly Refer to Fuses and rel
46. package of your vehicle the rear A console may be equipped with rear console audio climate controls 7 VOLUME MODE 2 Di COo e lt a SEEK B MEMORY S ER 4 ad Ondo Ne The instrument panel climate controls must be on in order for the rear console climate controls to work Turn the air distribution control to the desired airflow position Turn the fan speed control to the VOLUME MODE Ju desired position 0 aC jC lt q SEEK B MEMORY cogo 7 OOMO At Select A for air to flow through these vents 30 Controls and features Select 74 for air to flow through these vents REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel Press the rear defroster control to clear the rear window of thin ice and fog e The small LED will illuminate when the rear defroster is activated The ignition must be in the ON position to operate the rear window defroster The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position To manually turn off the defroster before ten minutes have passed push the control again 31 Controls and features 4WD CONTROL IF EQUIPPED This control operates the 4WD Refer to the Driving chapter for more information REVERSE SENSING SYSTEM IF EQUIPPED The reverse sensing system RSS sounds a tone to warn the driver of obstacles near
47. part to ground the circuit are the alternator mounting brackets or an engine lifting eye Do not use fuel lines engine rocker covers or the intake manifold as grounding points Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery e Engines except 4 0L SOHC e 4 0L SOHC 185 Roadside emergencies 5 Be sure that the cables are clear of fan blades belts and other moving parts of both engines Jump starting 1 Start the engine of the booster vehicle and run the engine at moderately increased speed 2 Start the engine of the disabled vehicle 3 Once the disabled vehicle has been started run both engines for a further three minutes before disconnecting the jumper cables Removing the jumper cables Remove the jumper cables in the reverse order that they were connected 1 Remove the jumper cable from the grownd metal surface e Engines except 4 0L SOHC 186 Roadside emergencies e 4 0L SOHC Roadside emergencies 2 Remove the jumper cable on the negative connection of the booster vehicle s battery 3 Remove the jumper cable from the positive terminal of the booster vehicle s battery 188 Roadside emergencies 4 Remove the jumper cable from the positive terminal of the disabled vehicle s battery After the disabled vehicle has been st
48. personalized oil reset percentage at optimal driving conditions 100 oil life is equivalent to a maximum of 12 000 kilometers 7 500 miles After you have the oil changed you must press and hold the OIL CHANGE RESET control for five seconds The message center will count down for five seconds After a successful reset the message center will display 18 Instrumentation OIL LIFE RESET TO 100 If you have established a personalized oil reset percentage the display will show that percentage instead of 100 This reset procedure should be performed only after an oil change to ensure accurate oil life indications Your personalized oil reset percentage allows you to establish a smaller oil change interval than the manufacturer s recommended interval To establish your personalized oil reset percentage 1 Press and hold the OIL CHANGE RESET control and press the RESET control while the display is still counting down the 5 seconds to reset The display will change to START OIL LIFE AT XXX 2 Press the OIL CHANGE RESET control until the displayed percentage is the personalized oil reset percentage you desire Your choices are 100 90 80 70 60 50 40 and 30 3 Press the RESET control to complete the procedure Pressing any control other than RESET or OIL CHANGE RESET will abort this procedure and will not establish your new personalized oil reset percentage When your personalized oil reset percentage has
49. preset controls will all store the last strong station available These stations are temporarily stored in the memory preset controls until deactivated and are accessed in the same manner of your original presets 51 Controls and features To deactivate autoset and return to your audio system s manually set memory stations press the AUTO control again Bass adjust The bass adjust control allows you to increase or decrease the audio hs gt i system s bass output Press the BASS control then press lt q to decrease the bass output and gt to increase the bass output Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output Press the TREB control then press lt to decrease the treble output and gt to increase the treble output Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Press the BAL control then press 52 Controls and features e lt q to shift sound to the left and e to shift sound to the right Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Press the FADE control then press e gt to shift the sound to the front and SEL J e lt q to shift the sound to the rear A Tape CD select e To begin tape play with a tape A loaded into the audio system PIT while in the r
50. rear seat passengers to scroll through the 6 memory presets in AM FM1 or FM2 Push the MEMORY control in CD changer mode if equipped to advance to the next disc Seek function e In radio mode press lt q to find the next listenable station down the frequency band frequency band e In tape mode use the SEEK function to access the next gt or previous lt selection e In CD mode if equipped use VOLUME MODE ee E E lt q SEEK B MEMORY C D 4 DORMO In radio mode press gt to find the next listenable station up the VOLUME MODE N CO lt SEEK B MEMORY CI R_S UO NO A the SEEK function to access the next gt or previous A selection 60 Controls and features MACH Audio System with AM FM Stereo Cassette Single CD VOL PUSH ON v DSC y O O C OOOOO Your audio system is equipped with selective lighting a unique lighting strategy This lighting feature is operable when the headlamps are illuminated During the operation of any selected mode lighting for the individual function controls will either illuminate or turn off Those controls which have a function for the specific mode of operation selected will be lit while the controls which have no function for that mode will be turned off Volume power control Press the control to turn the audio 7 system on or off VOL PUSH ON 6
51. securely latched in P Park A Never leave your vehicle unattended while it is running 147 Driving R Reverse With the gearshift in R Reverse the vehicle will move backward P RN D 2 1 Aways coke tc a complete Ss before shifting into and out of R Reverse N Neutral P RNO21 With the gearshift in N Neutral the vehicle can be started and is free to roll Hold the brake pedal down while in this gear Overdrive The normal driving position for the best fuel economy Transmission operates in gears one through four PRNQ 21 Co O 0 D The transmission control indicator light TCIL will illuminate on the 0 D instrument cluster O F F Drive Not shown on the display Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position The O D OFF indicator will illuminate on the instrument cluster Transmission operates in gears one through three Drive provides more engine braking than Overdrive and is useful when Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever e driving with a heavy load e towing a trailer up or down steep hills e additional engine braking is desired If towing a trailer refer to Driving while you tow in the Trailer Towing chapter To return to Overdrive mode press the transmission control switch The O D OFF ind
52. shortly after The indicator light will flash green twice 2 To delete all recorded messages simultaneously press and release the PLAY and REC buttons at the same time The indicator light will flash green twice If the DEL button is inadvertently pressed or the time allotted 5 seconds has passed the indicator light will flash amber and an error tone will sound AUTOLAMP DELAY SYSTEM IF EQUIPPED The autolamp sets the headlamps to turn on and off automatically The autolamp may be set to e turn on the lamps automatically at night e turn off the lamps automatically during daylight e keep the lamps on for up to three minutes after the key is turned to OFF 97 Controls and features Setting autolamp 1 Make sure the headlamp control is in the OFF position Leaving the headlamp control on will override the autolamp 2 Turn the ignition to the ON position or start the vehicle 3 Slide the delay control all the way to the left The further you move the knob to the right the longer the headlamps stay on after the ignition is turned to the OFF position The autolamp will keep the headlamps on for a maximum of three minutes after the ignition is turned to OFF 4 The autolamp automatically turns the lamps on and off The indicator light will illuminate when the headlamps turn on Automatic dimming rear view mirror The autolamp automatic dimming mirror is equipped with an automatic dim
53. specially equipped for driving on sand snow mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles both on and off the road Maintain steering wheel control at all times especially in rough terrain Since sudden changes in terrain can result in abrupt steering wheel motion make sure you grip the steering wheel from the outside Do not grip the spokes Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps You should either know the terrain or examine maps of the area before driving Map out your route before driving in the area For more information on driving off road read the Four Wheeling supplement in your owner s portfolio If your vehicle gets stuck If the vehicle is stuck in mud or snow it may be rocked out by shifting from forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle for more than a few minutes The transmission and tires may be damaged or the engine can overheat Do not spin the wheels at over 56 km h 85 mph The tires may fail and injure a passenger or bystander Sand When driving over sand try to keep all four wheels on the most solid area of the trail Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain Apply the accelerator slowly and avoid spinning the wheels Mud a
54. suspected or service is required The axle lubricant should be changed any time the axle has been submerged in water Add 118 ml 4 oz of additive friction modifier C8AZ 19B546 A Ford specification EST M2C118 A for complete refill of Traction Lok axles LUBRICANT SPECIFICATIONS Ford part name or equivalent High Performance Brake fluid DOT 3 Motor C6AZ 19542 AB Vehicle Brake Fluid Ford specification ESA M6C25 A and DOT 3 Body hinges latches door striker plates and rotors seat DOAZ 19584 AA Multi Purpose ESB M1C93 B or tracks fuel filler or door hinge and T S F5Az 19G209 AA ARMIA spring hood latch auxiliary latch 235 Capacities and specifications Ford part name or equivalent Driveshaft slip Piemium L r spline universal 8 X ESA M1C75 B oo Life Grease joints Engine coolant Ford Premium E2FZ 19549 AA ESE M97B44 A Engine Coolant green in color Ford Extended F6AZ 19544 AA WSS M97B44 D Life Engine or DEX COOL Coolant orange equivalent in color Motorcraft 5W30 ae e Engine oil Super Premium XO 5W30 QSP eae A Certification Motor Oil Mark 2 Ford specification Automatic transmission Automatic Motorcraft MERCON V MERCON V N Power steering Ford conventional and 2 2 Traction Lok rear axles 4x4 Gear Oil F1TZ 19580 A WSL M2C191 A Motorcraft Transfer case Premiui Front Output vag Tate Giens XG 1 G or K ESA M1C075 B S
55. the disc unless the CD changer is in E tune gt shuffle mode Refer to Shuffle feature for more information A Hold the control to continue reversing through the disc e Press gt to select the next disc in the CD changer Hold the control to fast forward through the remaining discs Seek function The seek function control works in radio tape or CD mode Seek function in radio mode e Press lt to find the next listenable station down the frequency band e Press P to find the next listenable station up the 4 4 frequency band 63 Controls and features Seek function in tape mode e Press lt q to listen to the previous selection on the tape e Press gt to listen to the next selection on the tape Seek function for CD changer if equipped e Press lt q to seek to the previous track of the current disc If a selection has been playing for three seconds or more and you press lt Q the CD changer will replay that selection from the beginning e Press J gt to seek forward to the next track of the current disc After the last track has been completed the first track of the current disc will automatically replay Scan function The scan function works in radio tape or CD mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the control again to stop the scan mode Scan function in tape mode
56. the control again Scan function in CD or CD changer mode if equipped Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again Radio station memory preset The radio is equipped with six station memory preset controls These controls can be used to select up to six preset AM stations and twelve FM stations six in FM1 and six in FM2 50 Controls and features Setting memory preset siations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station all Ani 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations This feature is helpful on trips when you travel between cities with different radio stations Starting autoset memory preset 1 Select a frequency using the AM FM select controls 2 Press the AUTO control 3 When the first six strong stations are filled the station stored in memory preset control 1 will start playing If there are less than six strong stations available on the frequency band the remaining memory
57. the disc will begin playing After that CD play will begin where it stopped last Eject function Press the control to stop and eject a CD Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level Controls and features ae A BAL as Press the COMP control to activate and deactivate compression adjust 45 Controls and features Setting the clock To set the hour press and hold the CLK control and press SCN CLK lt to decrease hours and gt to increase hours To set the minute press and hold the CLK control and press lt q to decrease minutes and pP to increase minutes lt 4 TUNE gt lt 4 TUNE gt ti _ fie 46 Controls and features Premium AM FM Siereo Casseite Single CD Premium Sound VOL PUSH ON SEEK A TUNE gt tune gt 7 Gar ss mes AL FADE SSeS Volume power control Press the control to turn the audio system on or off Audio power can also be turned on by pressing the AM FM select control or the tape CD select control Audio power is turned off by using the volume power control Turn control to raise or lower volume VOL PUSH ON VOL PUSH ON y v 47 Controls and features If the volume is set above a certain level and the ignition is turned off
58. the rear bumper when the reverse gear is selected The RSS will assist the driver in detecting certain objects while the vehicle slowly moves in reverse at speeds less than 8 km h 8 mph The RSS is not effective at speeds greater than 8 km h 3 mph and may not detect certain angular or moving objects The weather may also affect the function of RSS RSS may have reduced performance in the rain or snow 32 The reverse sensing system detects obstacles within approximately 1 8 meters 5 9 ft of the rear bumper with a decreased coverage area at the outer corners of the bumper As you move closer to the obstacle the rate of the tone increases When the distance to the obstacle is less than 20 0 cm 8 in the tone will sound continuously A reverse sensing control allows the driver to enable and disable the RSS when the ignition is ON The reverse sensing control indicator momentarily illuminates when the ignition is turned ON The OFF indicator remains illuminated when the system is disabled The system defaults to ON every time the reverse gear is selected The indicator will remain illuminated to indicate a failure of the reverse sensing system Controls and features Always keep the sensors located on the rear bumper fascia free from dirt snow and ice do not clean the sensors with sharp objects These elements may cause the system to operate inaccurately If the vehicle sustains damage to the rear bumper fascia
59. the shade must be manually rewound This is a two person operation 104 Controls and features 1 Remove the shade from the vehicle and extend it with the smooth grain facing you 2 Wrap the vinyl around the roller tube twice Tuck the edges of the vinyl inside the end cap with each wrap 3 Fold the edges of the vinyl towards the center making sure that the edges clear the end cap slots Use tape or a rubber band to hold the vinyl to the left side of the tube 4 Push in the right end cap marked RH about 1 4 of the total length to disengage the clutch and hold the end cap in while turning the roller tube toward you 14 times 5 Let go of the right end cap The clutch will now engage and stop the shade from losing its spring tension 6 Unfold the vinyl and place it into the end cap slots 7 Insert the shade into the side mounting brackets and check to make sure that it operates properly The cover may cause injury in a sudden stop or accident if it is not securely installed REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key The remote entry features only operate with the ignition in the OFF position 105 Controls and features Unlocking the doors Press this control to unlock the driver s door The interior lamps will illuminate Press the control a second time within five seconds to unlock all doors Locking the doors Press this
60. the volume will come back on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio tape and CD modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play AM FM select in CD or CD changer mode if equipped Press this control to stop CD play and begin radio play Tune adjust The tune control works in radio or CD changer mode Tune adjust in radio mode e Press lt q to move to the next frequency down the band whether or not a listenable station is located there Hold the Se control to move through the frequencies quickly e Press p gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement 48 Controls and features Tune adjust for CD changer if equipped e Press lt q to select the previous disc in the CD changer Play will begin on the first track of the SP disc unless the CD changer is in shuffle mode Refer to Shuffle feature for more information A Hold the control to continue reversing through the remaining discs Press gt to select the next disc in the CD changer Hold the control to fast forward through the remaining discs
61. these or any other temporary malfunctions present the Check Engine light should turn off A driving cycle consists of a cold engine startup followed by mixed city highway driving No additional vehicle service is required If the Check Engine light remains on have your vehicle serviced at the first available opportunity Light is blinking Engine misfire is occurring which could damage your catalytic converter You should drive in a moderate fashion avoid heavy acceleration and deceleration and have your vehicle serviced at the first available opportunity Under engine misfire conditions excessive exhaust temperatures could damage the catalytic converter the fuel system interior floor coverings or other vehicle components possibly causing a fire Fuel reset Iluminates when the ignition is turned to the ON position and the FUEL fuel pump shut off switch has been RESET triggered For more information refer to Fuel pump shut off switch in the Roadside emergencies chapter Air bag readiness Momentarily illuminates when the O O ignition is turned ON If the light A fails to illuminate continues to flash PV or remains on have the system serviced immediately Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts For more information refer to the Seating and safety restraints chapter Brake system warning Momentarily
62. to the 4WD system All utility type vehicles and 4WD vehicles have special design and equipment features to make them capable of performing in a wide variety of off road applications Specific design characteristics give them higher centers of gravity than ordinary passenger cars Utility and four wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low slung sports cars are designed to perform satisfactorily under off road conditions Avoid sharp turns or abrupt maneuvers in these vehicles AWD operation is not recommended on dry pavement Doing so could result in difficult disengagement of the transfer case increased tire wear and decreased fuel economy CONTROL TRAC AUTOMATIC FOUR WHEEL DRIVE SYSTEM IF EQUIPPED The 4WD system uses all four wheels to power the vehicle This increases traction enabling you to drive your 4x4 over terrain and road conditions not normally traveled by two wheel drive vehicles Power is supplied to all four wheels through a transfer case that allows you to select a four wheel drive mode best suited for your current driving conditions 152 Driving Positions of the Control Trac system The Control Trac system functions in three modes e The 4WD AUTO mode provides four wheel drive with full power delivered to the rear axle and to the front axle as required for increased traction This is appropriate for normal on road operating conditions such
63. 1 Controls and features Turn control to raise or lower VOL PUSH ON volume a N r y v If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on If you wish to maintain your preset volume level turn the audio system off with the power control before switching off the ignition AM FM select The AM FM select control works in radio tape and CD modes S gt m m AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in tape mode Press this control to stop tape play and begin radio play AM FM select in CD mode Press this control to stop CD play and begin radio play Tune adjust The tune control works in radio or CD mode 62 Controls and features Tune adjust in radio mode e Press E to move to the next frequency down the band whether or not a listenable a station is located there Hold the E tune amp control to move through the frequencies quickly ay i e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Tune adjust for CD changer if equipped e Press lt q to select the previous disc in the CD changer Play will begin on the first track of
64. 169 Roadside emergencies The fuel pump shut off switch is located in the passenger s foot well behind the kick panel FUSES AND RELAYS Fuses If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire within the fuse Check the appropriate 15 fuses before replacing any electrical components Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire 170 Roadside emergencies Standard fuse amperage rating and color COLOR Fuse Mini Standard Maxi oe Fuse Link Rating Fuses Fuses Fuses Fuses a a Grey Grey e E oe a ae Ca Pink Pink sa om m id o 758 Brown Brown ioa Red ro J id is Blue Blue _ _ 354 Natural Natural aoa Orange Green Orange sa Red f ra S Red eoa e S Yellow Coa tan Brown Peon Natural Black 171 Roadside emergencies Passenger compartment fuse panel Aa The fuse panel is located on the left hand side of the instrument panel facing the driver s side door Pull the panel cover outward to access the fuses To remove a fuse use the fuse puller tool provided on the fuse panel cover ge Lidke I
65. 2nd or 8rd press from step 3 will activate the door The HomeLink Universal Transceiver has now been trained to the receiver The remaining two buttons may now be programmed if this has not previously been done 7 Erasing HomeLink buttons Individual buttons cannot be erased however to erase the three programmed buttons 1 Hold down the two outside buttons until the red light begins to flash after 20 seconds 2 Release both buttons 95 Controls and features Reprogramming a single HomeLink button To program a device to HomeLink using a HomeLink button previously trained follow these steps 1 Press and hold the desired HomeLink button Do NOT release until step 4 has been completed 2 When the indicator light begins to flash slowly after 20 seconds position the hand held transmitter 5 14 cm 2 to 5 inches away from the HomeLink surface 3 Press and hold the hand held transmitter button 4 The HomeLink indicator light will flash first slowly and then rapidly When the indicator light begins to flash rapidly release both buttons The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed Operating TravelNote TravelNote records and stores messages for up to three minutes in total length with simple controls When you get an idea or remember something important while you re driving you don t have
66. 52 description 0 153 154 155 driving off road uo 155 158 electronic Shift eee 32 Fuel choosing the right fuel 214 comparisons with EPA fuel economy estimates 00 220 detergent in fuel 215 filling your vehicle with fuel 218 216 ANG C8 ian E E EEA ETE 15 quality sernrsiastenri teagan 215 running out of fuel 216 safety information relating to automotive fuels 0 213 FUSES ccssessces consti vaceecnecsss 170 171 172 Gas mileage see Fuel economy 217 218 219 220 GAUGES srpna aasievecs bess cacesitnt ees 11 engine coolant temperature TET OTA ARR E eves 12 engine oil pressure gauge 14 GVWR Gross Vehicle Weight Rating calculating ovsccvesssascsacsaserrgenssecss 162 Hazard flashers csrccresirsniris 169 Headlamps ANNE reee 227 autolamp system 00 97 98 bulb specifications 0 226 ish DEAN ccvscecsectaeivesevsdeesanes 9 20 warning chime sasise 11 GAUING sooner 21 heating and air conditioning SYSTE ccs actesessunsMeecanscncres 21 22 23 HOO ernenek 192 Ignitio senise ii 237 Index Inspection maintenance I M TESTING shaa RE 222 Instrument panel CLE ATG aiee peaa RES 231 Keyless entry system AUCOLOCIE sassone 109 110 K Y Pad vsccssascscesvessecaceuei nesses 111 locking and unlocking doors 112 programming entry CODE E E E 111 112 Keys key in ignition chime 11 positions of the igni
67. A N l I l Replacing the tires Replace the tires when the wear band is visible through the tire treads FAA When replacing full size tires never mix radial bias belted or bias type tires Use only the tire sizes that are listed on the tire pressure decal Make sure that all tires are the same size speed rating and load carrying capacity Use only the tire combinations recommended on the decal If you do not follow these precautions your vehicle may not drive properly and safely Make sure that all replacement tires are of the same size type load carrying capacity and tread design e g All Terrain etc as originally offered by Ford 211 Maintenance and care Do not replace your tires with high performance tires or larger size tires Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over Tires that are larger or smaller than your vehicle s original tires may also affect the accuracy of your speedometer SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains If you need to use chains it is recommended that steel wheels of the same size and specifications be used as chains may chip a
68. Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions 1 Overall length 2 Overall width 3 Overall height 4 Wheelbase 5 Track Front 5 Track Rear 1 487 58 5 238 Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety MFD BY FORD MOTOR CO IN U S A Administration Regulations Peguire DATE XXXXX GVWR XXXXX LB XXXXX KG that a Safety Compliance FGAWR XXXXXX KXXXXXX__ RGAWR XXXXXXX XXXXXXK soe as THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL Certification Label be affixed to a MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE i i r DATE OF MANUFACTURE SHOWN ABOVE e niece mie ong VIN XXXXXXXXXXXXXXXXX TYPE XXXXXXXXXXXXXXX Label may be located The Safety MAXIMUM LOAD OGCUPANTS LUGGAGE XXXKG XXXXLB Compliance Certification Label is OCCUPANTS X TOTAL X FR X 2ND X RR OCCUPANTS LUGGAGE XX XXXKG XXXXLB located on the front door latch pillar frire poxrooox sx X XXXKG XXXXLB on the driver s side PRESSURE FR XXX kPa 33 PSI COLD PRESSURE RR XXX kPa 33 PSI COLD TRAILER TOWING SEE OWNER GUIDE EXT PNT XXXXXX XXXXXX_ RC XX DSO XXXX_ F0000 BARTINTTR TP PS TR AXLE TR SPR 70000 X XX XXX X XX X XXXX UTC VFOHT 15294A10 GA 239 Capacities and specifications Vehicle identification number The vehicle identification number is
69. FORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing Ford may change the contents without notice and without incurring obligation SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle please read this Owner s Guide carefully Your vehicle is not a passenger car As with other vehicles of this type failure to operate this vehicle correctly may result in loss of control or an accident Be sure to read Driving off road in the Driving chapter as well as the Four Wheeling supplement included with 4WD and utility type vehicles Using your vehicle as a snowplow i Do not use this vehicle for snowplowing Using your vehicle as an ambulance A Do not use this vehicle as an ambulance Your vehicle is not equipped with the Ford Ambulance Preparation package Instrumentation Instrument cluster pg 6 Turn signal and wiper washer control pg 85 Driver side air bag pg 125 Instrument panel dimmer switch pg 21 Speed control 81 Tilt steering wheel lever ween pg 85 Instrumentation Rear window defroster control Electronic sound system pg 31 pg 34 Rear Gearshift includes window washer overdrive button control pg 149 pg 86 Climate controls pg 87 Fog lamp control pg 20 Instrumentation WARNING LIGH
70. Make sure the vehicle is on level ground 2 Turn the engine off and wait a few minutes for the oil to drain into the oil pan 3 Set the parking brake and ensure the gearshift is securely latched in P Park 194 Maintenance and care 4 Open the hood Protect yourself from engine heat 5 Locate and carefully remove the engine oil level indicator dipstick e 4 0L V6 engine e 5 0L V8 engine 6 Wipe the indicator clean Insert the indicator fully then remove it again e If the oil level is between the ADD and FULL marks 4 0L engine or between the MIN and MAX marks 5 0L engine the oil level is acceptable DO NOT ADD OIL 195 Maintenance and care e If the oil level is below the ADD mark 4 0L engine or MIN mark 5 0L engine add enough oil to raise the level within the ADD FULL range 4 0L engine or MIN MAX range 5 0L engine e Oil levels above the letter F in FULL 4 0L engine or the MAX mark 5 0L engine may cause engine damage Some oil must be removed from the engine by a service technician 7 Put the indicator back in and ensure it is fully seated Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine oil in this chapter 2 If the engine oil level is not within the normal range add only certified engine oil of the recommended viscosity Remove the engine oil filler cap and use a funnel to pour the engin
71. OR and VENT It will also operate only when required when AUTOMATIC has been selected However the air conditioning will only function if the outside temperature is about 10 C 50 F or above Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle Under normal conditions your vehicle s climate control system should be left in any position other than MAX A C or OFF when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct e MAX A C Uses recirculated air to cool the vehicle The temperature will display 16 C 60 F To exit press AUTOMATIC or any other override controls MAX A C is noisier than normal A C but more economical and will cool the inside of the vehicle faster Airflow is from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle e VENT Distributes outside air through the instrument panel registers However the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode 27 Controls and features PNLeFLR Distributes outside air through the instrument panel registers and the floor ducts Heating and air conditioning capabilities are provided in this mode The air will be heated or coo
72. Pull the bulb straight out of the socket and push in the new bulb 6 To complete installation follow the removal procedure in reverse order Replacing foglamp bulbs 1 Remove the bulb socket from the foglamp by turning counterclockwise 2 Disconnect the electrical connector from the foglamp bulb 3 Connect the electrical connector to the new foglamp bulb 4 Install the bulb socket in the foglamp turning clockwise 225 Maintenance and care License plate lamp bulbs To change the license plate bulbs 1 Remove two screws and the license plate lamp assembly from the liftgate 2 Remove bulb socket from lamp assembly by turning counterclockwise 3 Pull the bulb out from socket and push in the new bulb 4 Install the bulb socket in lamp assembly turning it clockwise 5 Install the lamp assembly on liftgate with two screws High mount brakelamp bulbs For bulb replacement see a dealer or qualified technician Using the right bulbs Park turn lamps front 2ST NAK Headlamps ooo 9007 Rear stop tail lamps TK Rear turn lamps 2 356K Rear license plate lamps 2 3156K 168 899 DO PDO Pho Lo Cargolamp l 211 2 m 912 906 Interior overhead lamp Front door courtesy lamp Map lamps Ashtray lamp 1 To replace all instrument panel lights see your dealer 226 Maintenance and care AIMING THE HEADLAMPS The alignment of your headlamps should be checked b
73. SUME controls are CONT pressed It turns off when the speed control OFF control is pressed the brake is applied or the ignition is turned to the OFF position 84 Controls and features TILT STEERING WHEEL Pull the tilt steering control toward you to move the steering wheel up or down Hold the control while adjusting the wheel to the desired position then release the control to lock the steering wheel in position A Never adjust the steering wheel when the vehicle is moving HAZARD FLASHER For information on the hazard flasher control refer to Hazard flasher in the Roadside emergencies chapter WINDSHIELD WIPER WASHER CONTROLS Rotate the windshield wiper control to the desired interval low or high speed position The bars of varying length are for intermittent wipers When in this position rotate the control upward for fast intervals and downward for slow intervals 85 Controls and features Push the control on the end of the stalk to activate washer Push and hold for a longer wash cycle The washer will automatically shut off after ten seconds of continuous use Speed dependent wipers When the windshield wiper control is set on the intermittent settings speed sensitive front wipers automatically adjust as the vehicle s speed increases Rear window wiper and washer For rear wiper operation rotate the rear window wiper and washer control to the desired interval position Press the c
74. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD The CD scans in a forward direction wrapping back to the first track at the end of the CD To stop on a particular selection press the control again 43 Controls and features Radio station memory preset The radio is equipped with four or six station memory preset controls These controls can be used to select up to four or six preset AM stations and eight or twelve FM stations four to six in FM1 and four to six in FM2 Setting memory preset stations 1 Select the frequency band with the AM FM select control 2 Select a station Refer to Tune adjust or Seek function for more information on selecting a station 3 Press and hold a memory preset control until the sound returns indicating the station is held in memory on the control you selected VOOWOOR Bass adjust The bass adjust control allows you i j to increase or decrease the audio A system s bass output BASS LV J Treble adjust The treble adjust control allows you N to increase or decrease the audio A system s treble output TREB 44 Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers CD select e To begin CD play if CD s are loaded press the CD control The first track of
75. Seek function The seek function control works in radio tape or CD mode Seek function in radio mode e Press lt q to find the next listenable station down the frequency band e Press gt to find the next listenable station up the 4 4 frequency band Seek function in tape mode e Press lt q to listen to the previous selection on the tape e Press p gt to listen to the next selection on the tape 4 Controls and features Seek function for CD or CD changer if equipped e Press lt q to seek to the previous track of the current disc If a selection has been playing for three seconds or more and you press lt Q the CD changer will 4 4 replay that selection from the beginning e Press gt to seek forward to the next track of the current disc After the last track has been completed the first track of the current disc will automatically replay Scan function The scan function works in radio cas tape or CD mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the control again to stop the scan mode Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape The tape scans in a forward direction At the end of the tape s first side direction automatically reverses to the opposite side of the tape To stop on a particular selection press
76. TS AND CHIMES Check engine Your vehicle is equipped with a computer that monitors the engine s CHECK emission control system This system is commonly known as the ENGINE On Board Diagnostics System OBD II This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards The OBD II system also assists the service technician in properly servicing your vehicle The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb If it comes on after the engine is started one of the engine s emission control systems may be malfunctioning The light may illuminate without a driveability concern being noted The vehicle will usually be drivable and will not require towing What you should do if the check engine light illuminates Light turns on solid This means that the OBD II system has detected a malfunction Temporary malfunctions may cause your Check Engine light to illuminate Examples are 1 The vehicle has run out of fuel The engine may misfire or run poorly 2 Poor fuel quality or water in the fuel Instrumentation 3 The fuel cap may not have been properly installed and securely tightened These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and or properly installing and securely tightening the gas cap After three driving cycles without
77. You can also obtain other information about motor vehicle safety from the Hotline 241 Index Air bag supplemental restraint SVSUCIM AO E E 125 and child safety seats 127 description 126 129 disposal seese 131 indicator light a se 129 131 passenger air bag 127 130 Air conditioning automatic temperature control system 24 25 26 27 28 29 rear seat controls 30 Air suspension GeSCTIPCION cceeeeseeeeeseeees 145 warning light 0 00 eee eeeeeeee 10 All Wheel Drive AWD driving off road eee 157 AYMTEStS o cceccccccceessecessetseeesseaees 103 Automatic transmission driving an automatic overdrive sinsin 147 148 149 150 151 152 Axle refill capacities 0 0 0 eee 233 Battery Voltage gauge oe eects 14 BRAGS en aerarii oi R 143 anti lok cesis nersniare 143 144 anti lock brake system ABS warning light eee 144 fluid checking and adding 197 shift interlock c eee 146 Break in period ccceeeeeees 2 3 Cargo area shade ccccceeee 104 Cargo COVED cscs sasceiusnceseareeressoss 104 CD Player sicissdisaiccuceees 76 78 79 80 Child safety seats attaching with tether straps 137 IN TEAL SeA seerne ian 135 tether anchorage hardware 138 Cleaning your vehicle 227 engine compartment 228 XLETIOT ces casas ieidseicsatvvvovee 228 230 242 exterior lamps ccceeeees 230 WIGETIOL j 2 l
78. ack on at a nominal listening level when the ignition switch is turned back on AM FM select The AM FM select control works in radio and CD modes AM FM select in radio mode This control allows you to select AM or FM frequency bands Press the control to switch between AM FM1 or FM2 memory preset stations AM FM select in CD mode Press this control to stop CD play and begin radio play Tune adjust The tune control works in radio mode Tune adjust in radio mode e Press lt Q to move to the next frequency down the band whether or not a listenable station is located there Hold the control to move through the frequencies quickly 42 Controls and features e Press gt to move to the next frequency up the band whether or not a listenable station is located there Hold for quick movement Seek function The seek function control works in radio or CD mode Seek function in radio mode e Press lt to find the next listenable station down the frequency band e Press J gt to find the next listenable station up the frequency band Seek function in CD mode e Press lt to listen to the next selection e Press gt to listen to the previous selection Scan function The scan function works in radio or CD mode Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band Press the SCAN control again to stop the scan mode
79. adio or CD mode press the TAPE control Press the button during rewind or fast forward to stop the rewind or fast forward function To begin CD play if CD s are loaded press the CD control The first track of the disc will begin playing If returning from radio or tape mode CD play will begin where it stopped last With the dual media audio system press the CD control to toggle between single CD and CD changer play if equipped 53 Controls and features Rewind The rewind control works in tape and CD modes gt e In tape mode radio play will continue until rewind is stopped with the TAPE control or the beginning of the tape is reached e In CD mode pressing the REW control rewinds the CD within the current track Fast forward The fast forward control works in tape and CD modes lt 4 e In the tape mode tape direction will automatically reverse when the end of the tape is reached e In CD mode pressing the control fast forwards the CD within the current track Tape direction select Press SIDE 1 2 to play the alternate side of a tape Eject function Press the EJ control to stop and eject a tape Press the EJ control to stop and eject a CD Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback Press the control to activate and deactivate the noise reduction 54 Controls and features Dolby noise redu
80. ance Always leave enough room between your vehicle and the vehicle in front of you to stop e We recommend that you familiarize yourself with this braking technique However avoid taking any unnecessary risks Parking brake Apply the parking brake whenever the vehicle is parked To set the parking brake press the parking brake pedal down until the pedal stops 144 Driving The BRAKE warning lamp in the instrument cluster illuminates and O remains illuminated when the BRAKE ignition is turned ON until the parking brake is released Always set the parking brake fully and make sure that the gearshift is securely latched in P Park The parking brake is not recommended to stop a moving vehicle However if the normal brakes fail the parking brake can be used to stop your vehicle in an emergency Since the parking brake applies only the rear brakes the vehicle s stopping distance will increase greatly and the handling of your vehicle will be adversely affected Pull the release lever to release the brake Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy AIR SUSPENSION SYSTEM IF EQUIPPED The load leveling feature of the air suspension automatically keeps the vehicle at a constant level if a load is added or removed from the vehicle This system maintains the vehicle height at a constant level by automatically adding air or releasing air from the springs to
81. and exhaust system creating the risk of fire or other damage Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Do not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes in this chapter for more instructions If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs faster to warm the engine If the engine idle speed does not slow down automatically have the vehicle checked Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and safety restraints chapter 2 Make sure the headlamps and vehicle accessories are off 139 Starting e Make sure the parking brake is set e Make sure the gearshift is in P Park 3 Turn the key to 4 ON without p turning the key to 5 START L 4 lt FUEL DOOR 4 gt el a ANS T JETO DOOR Make sure the corresponding lights
82. and the Empty Reserve combined Indicated Capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty Empty Reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty The amount of Empty Reserve varies and should not be relied upon to increase driving range When refueling your vehicle after the fuel gauge indicates empty you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank 217 Maintenance and care Filling the tank For consistent results e Use the same filling rate setting low medium high each time the tank is filled e Allow three automatic click offs when filling e Always use the recommended octane rating of a known quality gasoline preferably a national brand e Use the same side of the same pump and have the vehicle facing the same direction each time you fill up e Have the vehicle loading and distribution the same every time Your results will be most accurate if your filling method is consistent Calculating fuel economy 1 Fill the fuel tank completely and record the initial odometer reading 2 Each time you fill the tank record the amount of fuel added in liters or gallons 3 After at least three to five tank fill ups fill the fuel tank and record the current kilometer mileage reading 4 Follow one of
83. ap turn the engine off and let it cool 2 When the engine is cool wrap a thick cloth around the cap Slowly turn cap counterclockwise until pressure begins to release 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to turn it counterclockwise and remove the cap Change your engine coolant according to the appropriate schedule listed in the Scheduled Maintenance Guide Before adding engine coolant check the color of the coolant in your vehicle For vehicles with green coolant use Ford Premium Cooling System Fluid E2FZ 19549 AA in Canada Motorcraft CXC 8 B or an equivalent premium engine coolant that meets Ford specification ESE M97B44 A Do not add orange coolant or recycled coolant to your vehicle originally equipped with conventional green coolant For vehicles with orange coolant use Ford Extended Life Engine Coolant F6AZ 19544 AA or a DEX COOL equivalent that meets Ford specification WSS M97B44 D Do not add conventional green coolant or recycled coolant to your vehicle originally equipped with orange coolant Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze Do not use supplemental coolant additives in your vehicle These additives may harm your engine cooling system The use of an improper coolant may void your warranty of your vehicle s engine cooling system 200 Maintenance an
84. ar portion of the seat cushion 7 Press the control to move the seat forward backward up or down 117 Seating and safety restraints REAR SEATS Folding rear seats if equipped If your vehicle is equipped with a built in child seat the seatback cannot be folded down unless the built in child seat is fully stowed 1 Press the lower release control downward to unlatch the seatback 2 Rotate the seatback downward into the load floor position 3 Press down on the top outboard area of the seatback until a click is heard The seat is now latched in the floor position 118 Seating and safety restraints To return the seat to the upright position e Press downward on the upper corner of the seatback and hold e Pull the release handle upward to unlatch the seat e Rotate the seatback upward until the seatback latches in the upright position The seatback will click when it is locked into position SAFETY RESTRAINTS Safety restraints precautions A Always drive and ride with your seatback upright and the lap belt snug and low across the hips A To prevent the risk of injury make sure children sit where they can be properly restrained f Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision 119 Seating and safety restraints All occupants of the vehicle including the driver should always
85. arted and the jumper cables removed allow it to idle for several minutes so the engine computer can relearn its idle conditions WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member your roadside assistance center If equipped with air suspension the air suspension control must be turned to the OFF position The Ford approved towing procedure is flatbed or wheel lift with dollies On 4x2 vehicles it is acceptable to tow the vehicle with the front wheels on the ground without dollies and the rear wheels off the ground On 4x4 vehicles it is recommended that your vehicle be towed with a wheel lift or flatbed equipment with all the wheels off the ground 189 Roadside emergencies If the vehicle is towed by other means or incorrectly vehicle damage may occur Do not tow with slingbelt equipment Ford Motor Company has not developed or approved a T hook or slingbelt towing procedure A towing manual is available from Ford Motor Company for all authorized tow truck operators Have your tow truck driver refer to this manual for proper hook up and towing procedures for your vehicle 190 Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location
86. ated air is required Fan speed remains automatic unless the fan speed thumbwheel is turned or the steering wheel fan speed control is pressed When in AUTOMATIC and weather conditions require heat air will be sent to the floor However if the engine is not warm enough to provide heat the fan will be at a low speed and the air will be directed to the windshield In 314 minutes or less the fan speed will start to increase and the airflow location will change to the floor area If unusual conditions exist i e window fogging etc the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary Temperature selection The display window indicates the SF selected temperature function C CAUTO or one of the override AUTO controls and manual control of fan speed l8 if automatic fan speed is not desired 25 Controls and features To control the temperature select any temperature between 18 C 65 F and 29 C 85 F by pressing the blue cooler or red warmer buttons CD REAR FAN OFF MEAS For continuous maximum cooling push the blue button until 16 C 60 F is shown in the display window The EATC will continue maximum cooling disregarding the displayed temperature until a warmer temperature is selected by pressing the red button C For continuous maximum heating push the red button until 32 C 90 F is shown in th
87. ater stops beading on the surface This could be every three or four months depending on operating conditions Use only carnauba or synthetic based waxes Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle Use tar remover to remove any tar spots Avoid getting wax on the windshield If you have wax applied at a commercial car wash it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch up paint repair foil or aerosol paint spray from the Ford accessory line Observe the application instructions on the products Remove particles such as bird droppings tree sap insect remains tar spots road salt and industrial fallout immediately Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal When washing e Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage e Do not spray with cold water to avoid cracking the engine block or other engine components e Cover the highlighted areas to prevent water damage when cleaning the engine 228 Maintenance and care e 4 0L SOHC e Never wash or rinse the engine while it is running water in the
88. ature the needle remains within the normal area the area I between the H and C If it enters the red section the engine is Ny H overheating Stop the vehicle as soon as safely possible switch off C the engine immediately and let the engine cool Refer to Engine coolant in the Maintenance and care chapter Never remove the coolant reservoir cap while the engine is running or hot This gauge indicates the temperature of the engine coolant not the coolant level If the coolant is not at its proper level the gauge indication will not be accurate 12 Instrumentation Odometer Registers the total kilometers miles of the vehicle Trip odometer Registers the kilometers miles of individual journeys To reset depress the control 80 s 10 ag 90 1 400 s 000000 100 e180 MPH km h 120 Tachometer Indicates the engine speed in revolutions per minute Driving with your tachometer pointer continuously at the top of the scale may damage the engine 13 Instrumentation Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position If the pointer moves and stays outside the normal operating range as indicated have the vehicle s electrical system checked as soon as possible H rr Engine oil pressure gauge This shows the engine oil pressure in the system Sufficient pressure exists as long as the n
89. ays in the Roadside emergencies chapter Do not drive your vehicle until you verify that the brakelamps are working If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear 146 Driving Do not rock the vehicle for more than a few minutes The transmission and tires may be damaged or the engine may overheat Always set the parking brake fully and make sure the gearshift is latched in P Park Turn off the ignition whenever you leave your vehicle If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your dealer or a qualified service technician Driving with a 4 speed automatic transmission if equipped Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift Hold the brake pedal down while you move the gearshift lever from P Park to another position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone P Park Always come to a complete stop O 2 before shifting into P Park Make PRN 1 sure the gearshift is securely latched o ES in P Park This position locks the transmission and prevents the rear wheels from turning Always set the parking brake fully and make sure the gearshift is
90. bs Jb4 AEN EmA Lis Lia Les Lre 7 Lae Je J 20 La Le Le Lea Le Le Le ee 2 Cs Ls Le e E 172 Roadside emergencies The fuses are coded as follows Fuse Relay Fuse Amp Description Location Rating Power Mirror Switch Power Antenna 2 7 5A Blower Motor Relay Air Bag Diagnostic Monitor 6 75A Rear Blower Motor Without EATC 8 10a Right Headlamp Foglamp Relay 9 75A Brake Pedal Position Switch _ 10 7 5A Speed Control Amplifier Assembly Generic Electronic Module GEM Shift Lock Actuator Blend Door Actuator A C Heater Assembly Flasher Overhead Console Load Leveling Module 12 7 5A Washer Pump Relay Rear Washer Pump Relay 13 20A Brake Pedal Position Switch Brake Pressure Switch 14 10A 4 Wheel Anti Lock Brake System 4WABS Module 4WABS Main Relay 16 30A Windshield Wiper Motor Wiper Hi Lo Relay Wiper Run Park Relay 18 25A Drivers Unlock Relay All Unlock Relay All Lock Relay PCM Power Diode 20 7 5A RAP Module Generic Electronic Module GEM Radio Cellular Phone 173 Roadside emergencies Fuse Relay Fuse Amp Description Location Rating Flasher Hazard 23 NotUseq 24 7 5A Clutch Pedal Position CPP Switch Starter Interrupt Relay Anti Theft 25 7 5A Generic Electronic Module GEM Instrument Cluster Securi Lock 26 10A Battery Saver Relay Electronic Shift Relay Interior Lamp Relay Electronic Shift Control Module
91. cesesteseeenees 13 Panic alarm feature remote entry syste 15200 ccsscancrssiececacens cs 106 Parking brake c eee 144 Power distribution box see BUSES innta 175 Power door locks ssiissssiisrissssis 100 Power steering fluid checking and adding 201 Radio 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 57 58 59 60 61 62 63 64 65 66 67 68 69 Relays woc cccecccccessesceeesseeessesseeees 170 Remote entry system 105 118 114 115 illuminated entry 109 locking unlocking doors 106 replacement additional TYANSMUCLETS ccccevciecseccesseseeeccs 109 replacing the batteries 108 Reverse sensing system 32 ROOE TACK visa caacscestahestsisterearees 167 Safety belts see Safety restraints 11 Safety restraints cleaning the safety belts 125 231 extension assembly 124 FOF Children sscsisssascecissetsscascscs 132 244 warning light and chime Seat belts see Safety 11 124 restraints 119 120 121 122 123 DEALS wooeccccccccsesscecssseseessseeeesees 116 child safety seats 0ce 133 CLE ATMS 335 cas neesevdcensaveetaces 230 231 Memory SE oo ceeeeeeeeeeceeeeeeee 107 Servicing your vehicle 191 SNOWDPIOWING ou eeeeteeeeeeeeeteeees 3 Spark plugs specifications 233 Special notice cc cceeeeeeeeeeee 3 ambulance conversions 5 3 utility type vehicles
92. ck If the vehicle is stuck in mud or snow it may be rocked out by shifting from forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear Do not rock the vehicle for more than a few minutes The transmission and tires may be damaged or the engine can overheat Do not spin the wheels at over 56 km h 85 mph The tires may fail and injure a passenger or bystander 155 Driving Sand When driving over sand try to keep all four wheels on the most solid area of the trail Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain Apply the accelerator slowly and avoid spinning the wheels Mud and water If you must drive through high water drive slowly Traction or brake capability may be limited When driving through water determine the depth avoid water higher than the bottom of the hubs Gf possible and proceed slowly If the ignition system gets wet the vehicle may stall Once through water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal After driving through mud clean off residue stuck to rotating driveshafts and tires Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components If the transmission transfer case or front axle are
93. ction manufactured under license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation Compression adjust Compression adjust brings soft and loud CD passages together for a eet more consistent listening level P Press the COMP control to activate and deactivate compression adjust Shuffle feature The shuffle feature operates in CD d mode and plays all tracks on the gt current disc in random order If equipped with the CD changer the shuffle feature continues to the next disc after all tracks on the current disc are played Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again Setting the clock To set the hour press and hold the CLK control and press SEEK e lt q to decrease hours and e p to increase hours l i 55 Controls and features To set the minute press and hold the CLK control and press TUNE e lt q to decrease minutes and e gt to increase minutes If your vehicle has a separate clock module other than the digital radio display the CLK button will not function in the above manner The CLK button will allow you to switch between media display mode radio station stereo information etc and clock display mode time When in clock mode the media information will display for ten seco
94. d care Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln Mercury dealers use recycled engine coolant produced by Ford approved processes For vehicles with green coolant not all coolant recycling processes produce coolant which meets Ford specification ESE M97B44 A and use of such coolant may harm engine and cooling system components For vehicles with orange coolant no recycling process has been approved at this time and use of such coolant may harm engine and cooling system components Always dispose of used automotive fluids in a responsible manner Follow your community s regulations and standards for recycling and disposing of automotive fluids Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in the Capacities and specifications chapter Have your dealer check the engine cooling system for leaks if you have to add more than 1 0 liter 1 0 quart of engine coolant per month Severe winter climate If you drive in extremely cold climates less than 36 C 34 F it may be necessary to increase the coolant concentration above 50 Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months Never increase the engine coolant concentration above 60 Leave a 50 50 mixture of engine coo
95. d the control for three seconds to turn the feature on or off Press the control to scroll through the following selections 70 Controls and features RDS traffic announcement e Press the RDS control until TRAFFIC is displayed e Use the SELECT control to select ON or OFF With the feature ON use the SEEK or SCAN control to find a radio station broadcasting a traffic report if it is broadcasting RDS data RDS select program type e Press the RDS control until FIND program type is displayed 71 Controls and features Use the SEL control to select the program type With the feature on use the SEEK or AUTOSET or SCAN control to find the desired program type from the following selections Classic Country Info Jazz R amp B Religious Rock Soft Top 40 RDS show With the RDS menu enabled press the RDS control until SHOW is displayed Use the SEL control to select TYPE NAME TEXT or NONE When your radio is turned to a RDS station RDS station TYPE station NAME or TEXT message will be displayed along with the frequency Press SEL in order to scroll through the text messages 72 Mute mode Press the control to mute the playing media Press the control again to return to the playing media Rear seat controls if equipped The Personal Audio System a feature of the optional Premium AM FM Stereo Cassette Single CD Premium Sound and the MACH Audio System with AM FM Stereo Cas
96. e GAWR Gross Axle Weight Rating Carrying capacity for each axle system The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar e GCWR Gross Combined Weight Rating Maximum combined weight of towing vehicle including passengers and cargo and the trailer The GCWR indicates the maximum loaded weight that the vehicle is designed to tow e Maximum Trailer Weight Rating Maximum weight of a trailer the vehicle is permitted to tow The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine transmission combination any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle e Maximum Trailer Weight maximum weight of a trailer the loaded vehicle including passengers and cargo is permitted to tow It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle e Trailer Weight Range Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating Remember to figure in the tongue load of your loaded trailer when figuring the total weight Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle s GVWR and GAWR limitations
97. e buckle closest to the direction the tongue is coming from for that seating position until you hear a snap and feel the latch engage Make sure the tongue is latched securely by pulling on it 5 To put the retractor in the automatic locking mode grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the automatic locking mode 136 Seating and safety restraints 7 Pull the lap belt portion across the child seat toward the buckle and g pull up on the shoulder belt while pushing down with your knee on the child seat 8 Allow the safety belt to retract to remove any slack in the belt 9 Before placing the child in the seat forcibly tilt the seat forward and back to make sure the seat is securely held in place 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat steps two through nine Check to make sure the child seat is properly secured before each use Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point Other manufacturers offer the tether strap as an accessory Contact t
98. e display window The EATC will continue maximum heating disregarding the displayed temperature until a cooler temperature is selected by pressing the blue button Temperature conversion Press MAX A C and DEF H at the same time for one second to at aid switch between Fahrenheit and reno 7 auroman Celsius eae r r Ceo ae 0 If your vehicle has an English Metric E M control this control will also change the temperature display Fan speed 8 When AUTOMATIC is pressed fan speed is adjusted automatically for existing conditions You can override fan speed at any time To control fan speed manually use the AUTOMATIC thumbwheel or steering wheel control to cancel automatic fan speed operation FLR DEF DEF 7 26 Controls and features e Rotate the thumbwheel up for higher fan speed or down for lower fan speed e Press the steering wheel fan speed control up for higher fan speed or down for lower fan speed The display will show Ei to indicate amp F manual fan operation J_ auto To return to automatic fan operation press AUTOMATIC Manual override controls The override controls are located at the bottom of the EATC and allow you to determine where airflow is cracls directed To return to full automatic control press AUTOMATIC The air conditioning compressor will operate in all modes except FLO
99. e oil into the opening 3 Recheck the engine oil level Make sure the oil level is not above the MAX mark or the letter F in FULL on the dipstick Engine oil and filter recommendations Look for this certification mark Motorcraft SAE 5W 30 1QUART 0 946L Ford oil specification is WSS M2C153 G Use SAE 5W 30 motor oil certified for gasoline engines by the American Petroleum Institute 196 Maintenance and care Do not use supplemental engine oil additives oil treatments or engine treatments They are unnecessary and could under certain conditions lead to engine damage which is not covered by your warranty Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications startup engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed Refer to the Scheduled Maintenance Guide for the service interval schedules 1 Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir 2 Visually in
100. e tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure SERVICING YOUR TIRES Checking the tire pressure e Use an accurate tire pressure gauge e Check the tire pressure when tires are cold after the vehicle has been parked for at least one hour or has been driven less than 5 km 3 miles e Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label located on the drivers door jamb Improperly inflated tires can affect vehicle handling and can fail suddenly possibly resulting in loss of vehicle control Tire rotation Because your vehicle s tires perform different jobs they often wear differently To make sure your tires wear evenly and last longer rotate them as indicated in the Schedule maintenance guide If you notice that the tires wear unevenly have them checked 210 Maintenance and care e Four tire rotation N AN K
101. e warning chime sounds for four to position eight seconds The driver s safety belt is The safety belt warning light and buckled while the indicator warning chime turn off light is illuminated and the warning chime is sounding The driver s safety belt is The safety belt warning light and buckled before the ignition indicator chime remain off switch is turned to the ON position 124 Seating and safety restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged Inspect the safety belts to make sure there are no nicks wears or cuts replacing if necessary All safety belt assemblies including retractors buckles front seat belt buckle assemblies slide bar if equipped shoulder belt height adjusters if equipped child safety seat tether bracket assemblies if equipped and attaching hardware should be inspected after a collision Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced However if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly they do not need to be replaced Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Failure to inspect and if necessary replace the safety belt assembly under the above conditions could re
102. ear of the vehicle until UNLOCKED appears 2 Slide cross bar to the desired location 3 Lock the cross bar into position by pushing the locking switches on each end of the crossbar toward the front of the vehicle The rear rack can be completely removed in the UNLOCKED position by sliding the cross bar rearward until it frees the guides 168 Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown approaching danger etc The hazard flashers can be operated when the ignition is off e The hazard lights control is located on top of the steering column Depress hazard lights control to activate all hazard flashers simultaneously e Depress control again to turn the flashers off FUEL PUMP SHUT OFF SWITCH After a collision if the engine cranks but does not start the fuel pump shut off switch may have been activated The Fuel Reset indicator light will illuminate in the instrument cluster The shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt 1 Turn the ignition to the OFF position 2 Check the fuel system for leaks 3 If no fuel leak is apparent reset the fuel pump shut off switch by pushing in the reset button 4 Turn the ignition to the ON position Pause for a few seconds and return the key to the OFF position 5 Make a further check for leaks in the fuel system
103. eating and safety restraints Do not attempt to service repair or modify the Air Bag Supplemental Restraint System or its fuses See your Ford or Lincoln Mercury dealer Children and air bags For additional important safety information read all information on safety restraints in this guide Children must always be properly restrained Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Failure to follow these instructions may increase the risk of injury in a collision Air bags can kill or injure a child in a child seat NEVER place a rear facing child seat in front of an active air bag If you must use a forward facing child seat in the front seat move the seat all the way back Na A How does the air bag supplemental restraint system work The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Air bags are designed to inflate in frontal and 127 Seating and safety restraints near frontal collisions not rollover side impact or rear impacts The air bags inf
104. ed on rear edge of each rear door and must be set separately for each door Setting the lock for one door will not automatically set the lock for both doors Move lock control up to engage the lock Move control down to disengage childproof locks 100 Controls and features POWER SIDE VIEW MIRRORS To adjust your mirrors 1 Select lt q to adjust the left mirror or B gt to adjust the right mirror 2 Move the control in the direction you wish to tilt the mirror 3 Return to the center position to lock mirrors in place Heated outside mirrors if equipped Both mirrors are heated automatically to remove ice mist and fog when the rear window defrost is activated Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place These actions could cause damage to the glass and mirrors CENTER CONSOLE Your vehicle may be equipped with a variety of console features These include e utility compartment with cassette compact disc storage e auxiliary power point e cupholders e tissue box holder 101 Controls and features e ashcup e compact disc changer if equipped e removable utility bag if equipped Use only soft cups in the cupholder Hard objects can injure you in a collision Auxiliary power point The power point is an additional power source for electrical accessories Rear console features The rear console incorpo
105. eduction reduces the amount of hiss and static during gt tape playback Press the control to activate and deactivate the noise reduction 68 Controls and features Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation Compression adjust Compression adjust brings soft and loud CD passages together for a eet more consistent listening level P Press the COMP control to activate and deactivate compression adjust Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order If equipped with the CD changer the shuffle feature continues to the next disc after all tracks on the current disc are played Press the SHUFFLE control to start this feature Random order play will continue until the SHUFFLE control is pressed again Setting the clock Press the clock RDS control until SELECT HOUR is displayed and press e a to decrease hours and gt to increase hours 69 Controls and features To set the minute press the clock RDS control until SELECT MIN is displayed and press lt q to decrease minutes and gt to increase minutes Radio Data System RDS feature This feature allows your audio system to receive text information from RDS equipped FM radio stations Press and hol
106. eedle remains in the normal range the area between the L and H H If the gauge indicates low pressure W7 p stop the vehicle as soon as safely possible and switch off the engine immediately Check the oil level Add oil if needed refer to Engine oil in the Maintenance and care chapter If the oil level is correct have your vehicle checked at your dealership or by a qualified technician 14 Instrumentation Fuel gauge Displays approximately how much lt fuel is in the fuel tank when the FUEL DOOR key is in the ON position The fuel gauge may vary slightly when the vehicle is in motion The ignition should be in the OFF position while the vehicle is being refueled When the gauge first indicates empty there is a small amount of reserve fuel in the tank When refueling the vehicle from empty indication the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located MESSAGE CENTER IF EQUIPPED With the ignition in the ON position the message center displays important vehicle information through a constant monitor of vehicle systems You may select display features on the message center for a display of status preceded by a brief indicator chime The system will also notify you of potential vehicle problems with a display of system warnings 15 In
107. een turned on with the dimmer control or e any door is open The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position Autolock Autolock is a feature that will automatically lock all doors when e all vehicle doors liftgate and liftgate window are fully closed e the ignition key is in the ON position e you shift into or through R Reverse e the brake pedal is released 109 Controls and features The autolock feature repeats when e any door is opened and then closed e the brake pedal is released Deactivating autolock Before following the activation or deactivation procedures make sure that the ignition is OFF and all vehicle doors and liftgate window are closed 1 Enter the 5 digit entry code 2 Press and release the 3 4 control while holding the 7 8 control 1 2 3 4 5 6 7 8 w0 3 Release the 7 8 control 4 The horn will chirp once if autolock was deactivated or twice one short and one long chirp if autolock was activated To reactivate autolock repeat steps 1 through 3 Autolock can also be activated or deactivated using the following procedure You must complete steps 1 through 5 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Turn the ignition key from OFF to RUN ACC 2 Press the power door UNLOCK control three times 3 Tu
108. eetteeeteeees 99 100 rear wiper washef 0000 86 Windshield washer fluid and wipers checking and cleaning 208 operaatiot 225ccee5 sare desewsstezanddesacaades 85 replacing wiper blades 208 245 246 247 Filling station information Recommended fuel Unleaded fuel only 87 octane 78 7L 20 8 gallons Engine oil capacity includes filter 4 7L 5 0 quarts Use Motorcraft change 5W30 Super Premium Motor Oil Ford specification WSS M2C153 G Tire size and pressure See Safety Compliance Certification Label on inside of driver door Hood release Pull handle under the instrument panel Coolant _capacity 4 0L SOHC V6 13 2L 14 0 quarts engine Coolant capacity 5 0L V8 engine 14 9L 15 7 quarts Power steering fluid capacity Fill to line on reservoir Use Motorcraft MERCON ATF Automatic transmission fluid 13 1L 18 9 quarts Use capacity 4R70W with 5 0L V8 Motorcraft MERCON V ATF engine AWD Automatic transmission fluid 9 5L 10 0 quarts Use Motorcraft capacity 4x2 vehicles with 5R55E MERCON V ATF and 4 0L SOHC V6 engine Automatic transmission fluid 9 8L 10 3 quarts Use Motorcraft capacity 4x4 vehicles with 5R55E MERCON V ATF and 4 0L SOHC V6 engine 1 If your engine coolant is green in color use Ford Premium Cooling System Fluid If your engine coolant is orange in color use Ford Extended Life Engine Coolant Refer to Adding engine coolant
109. emoved for an extended period of time contaminants may enter the lamp housings and affect lamp performance Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass The oil from your hand could cause the bulb to break the next time the headlamps are operated If the bulb is accidentally touched it should be cleaned with rubbing alcohol before being used To remove the headlamp bulb 1 Make sure headlamp switch is in OFF position then lift hood and open the hinged headlamp cover 2 Release clip and disconnect the electrical connector from the bulb SY p cr i T i 223 Maintenance and care 3 Remove the bulb retaining ring by rotating it counterclockwise when viewed from the rear about 1 8 gt b turn to free it from the bulb socket Se and slide the ring off the plastic Dear base Keep the ring to retain the Fe 3 new bulb 4 Remove the old bulb from the lamp assembly by gently pulling it straight back out of the lamp assembly To install the new bulb 1 With the flat side of the new bulb s plastic base facing upward insert the glass end of the bulb into the lamp assembly You may need to 6 turn the bulb left or right to align gt SQ Ci the grooves in the plastic base with SY the tabs in the lamp assembly When the grooves are aligned push the bulb into the lamp
110. empt to push start your vehicle Automatic transmissions do not have push start capability Preparing your vehicle 1 Use only a 12 volt supply to start your vehicle 2 Do not disconnect the battery of the disabled vehicle as this could damage the vehicle s electrical system 3 Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts 4 Check all battery terminals and remove any excessive corrosion before you attach the battery cables Ensure that vent caps are tight and level 5 Turn the heater fan on in both vehicles to protect any electrical surges Turn all other accessories off 183 Roadside emergencies Connecting the jumper cables 1 Connect the positive booster cable to the positive terminal of the discharged battery Note In the illustrations lightning bolts are used to designate the assisting boosting battery 2 Connect the other end of the positive cable to the positive terminal of the assisting battery 184 Roadside emergencies 3 Connect the negative cable to the negative terminal of the assisting battery 4 Make the final connection of the negative cable to an exposed metal part of the stalled vehicle s engine away from the battery and the carburetor The preferred locations of an exposed metal
111. es and suspension For your safety and to maximize vehicle performance be sure to use the proper equipment while towing Follow these guidelines to ensure safe towing procedure e Stay within your vehicle s load limits e Thoroughly prepare your vehicle for towing Refer to Preparing to tow in this chapter e Use extra caution when driving while trailer towing Refer to Driving while you tow in this chapter e Service your vehicle more frequently if you tow a trailer Refer to the severe duty schedule in the service guide and or maintenance guide e Do not tow a trailer until your vehicle has been driven at least 800 km 500 miles e Refer to the instructions included with towing accessories for the proper installation and adjustment specifications Do not exceed the maximum loads listed on the Safety Compliance Certification label For load specification terms found on the label refer to Vehicle loading in this chapter Remember to figure in the tongue load of your loaded vehicle when figuring the total weight 163 Driving Trailer towing table 4x2 GCWR Gross Combined Weight Rating Trailer Weights Trailer Weight Maximum Range kg ibs frontal area of 0 Maximum trailer m ft 4 0L 4 082 0 2 041 SOHC 9 000 0 4 500 ad Ga 4 0L 4 535 0 2 649 SOHC 10 000 0 5 840 eee OU 4 990 0 3 030 11 000 0 6 680 faa Trailer towing table 4x4 and AWD automatic transmission 4 0L 4 082 0 2 041 SOHC 9 000 0 4
112. est fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal e Four wheel drive operation if equipped is less fuel efficient than two wheel drive operation e Close windows for high speed driving EPA window sticker Every new vehicle should have the EPA window sticker Contact your dealer if the window sticker is not supplied with your vehicle The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles It is important to note the box in the lower left corner of the window sticker These numbers represent the Range of Km L MPG expected on the vehicle depending upon the driver s method of operation and conditions 220 Maintenance and care EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards To make sure that the catalytic converter and other emission control components continue to work properly e Use only unleaded fuel e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds e Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system
113. f hand held transmitters To operate simply press and release the appropriate HomeLink button the red light will illuminate indicating the signal is being transmitted Rolling code programming Rolling code garage door openers or other rolling code devices which are code protected and manufactured after 1996 may be determined by the following e Reference the device owner s manual for verification e The hand held transmitter appears to program the HomeLink Universal Transceiver but does not activate the device e Press and hold the trained HomeLink button The device has the rolling code feature if the indicator light flashes rapidly and then turns solid after 2 seconds 94 Controls and features After completing the Programming functions follow these steps to train a garage door opener with the rolling code feature 1 Locate the training button on the garage door motor head unit Refer to the garage door opener manual or call 1 800 355 3515 or on the Internet at HomeLink jci com if there is difficulty locating the training button 2 Press the training button on the garage door motor head unit which will activate the training light 3 Press and release the programmed HomeLink button Press and release the HomeLink button a second time to complete the training process Some garage door openers may require this procedure to be done a third time to complete the training The
114. g mirrors Do not clean your mirrors with a dry cloth or abrasive materials Use a soft cloth and mild detergent and water Be careful when removing ice from outside mirrors because you may damage the reflective surface 232 Capacities and specifications MOTORCRAFT PART NUMBERS Component 4 0L SOHC V6 5 0L V8 engine engine FA 1658 FA 1658 Fuel filter FG 986B FG 986B Battery standard BXT 65 650 BXT 65 650 Refer to Vehicle Emissions Control Information VECI decal for spark plug gap information Tf a spark plug is removed for inspection it must be reinstalled in the same cylinder Cylinders No 1 2 3 and 4 have a EG suffix Cylinders No 5 6 7 and 8 have a E suffix If a spark plug needs to be replaced use only spark plugs with the service number suffix letter as shown on the engine decal REFILL CAPACITIES Fluid Ford Part Application F a re Teaser All Brake fluid High Performance i DOT 3 Motor te eee Vehicle Brake Fluid Engine oil Motorcraft 5W30 All ATL including filter Super Premium change Motor Oil 5 0 quarts Fuel tank N A All 78 7L 20 8 gallons Power steering Motorcraft All Fill to line on fluid MERCON ATF reservoir 233 Capacities and specifications Fluid Ford Part Application a re Teac Transmission Motorcraft 4R70W fluid MERCON V Automatic with 13 1L ATF 5 0L V8 engine 13 9 quarts AWD 5R55E 9 5L Automatic with 10 0 quarts 4 0L SOHC
115. ges You may want to turn off the speed control in hilly terrain as unnecessary shifting between third and fourth gears may occur and could result in reduced fuel economy Warming up a vehicle on cold mornings is not required and may reduce fuel economy Resting your foot on the brake pedal while driving may reduce fuel economy Combine errands and minimize stop and go driving Maintenance Keep tires properly inflated and use only recommended size Operating a vehicle with the wheels out of alignment will reduce fuel economy Use recommended engine oil Refer to Lubricant Specifications Perform all regularly scheduled maintenance items Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide 219 Maintenance and care Conditions e Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed Carrying unnecessary weight may reduce fuel economy approximately 2 km h 1 mpg is lost for every 180 kg 400 lb of weight carried e Adding certain accessories to your vehicle for example bug deflectors rollover light bars running boards ski luggage racks may reduce fuel economy e Use of fuel blended with alcohol may lower fuel economy e Fuel economy may decrease with lower temperatures during the first 12 16 km 8 10 miles of driving e Flat terrain driving improves fuel economy over hilly roads e Transmissions give their b
116. gin tape play with a tape loaded into the audio system ITA while in the radio or CD mode S press the TAPE control Press the button during rewind or fast forward to stop the rewind or fast forward function e To begin CD play Gf CD s are loaded press the CD control The first track of the disc will begin playing After that CD play will begin where it stopped last If equipped with a CD changer press the CD control to toggle between single CD and CD changer play 67 Controls and features Rewind The rewind control works in tape and CD modes e In tape mode radio play will continue until rewind is stopped with the TAPE control or the beginning of the tape is reached e In CD mode pressing the REW control for less than three seconds results in slow rewind Pressing the control for more than three seconds results in fast rewind Fast forward The fast forward control works in tape and CD modes e In the tape mode tape direction will automatically reverse when the end of the tape is reached e In CD mode pressing the control for less than three seconds results in slow forward action Pressing the control for more than three seconds results in fast forward action Tape direction select Press SIDE 1 2 to play the alternate side of a tape E gt Eject function Press the control to stop and eject a Press the control to stop and eject a Dolby noise reduction Dolby noise r
117. gnition in RUN for at least one second This step will program your new SecuriLock key 6 To program additional SecuriLock key s repeat this procedure from step 1 If the programming procedure was successful the new SecuriLock key s will start the vehicle s engine The theft indicator located on the instrument cluster will light for three seconds and then go out If the programming procedure was not successful the new SecuriLock key s will not operate the vehicle s engine The theft indicator will flash on and off Wait at least one minute and then repeat the procedure from step 1 If failure repeats bring your vehicle to your dealership to have the spare SecuriLock key s programmed 115 Seating and safety restraints SEATING Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to A increase firmness Turn the lumbar support control I toward the rear of vehicle to increase softness Adjusting the front power seat if equipped A Never adjust the driver s seat or seatback when the vehicle is moving f Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop fp Always drive and ride with your seatback upright and the lap belt snug and low across the hips 116 Seating and safety restraints Press to raise or lower the front N portion of the seat cushion 7 7 Press to raise or lower the re
118. hains under the trailer tongue and allow slack for turning corners If you use a rental trailer follow the instructions that the rental agency gives to you Do not attach safety chains to the bumper Trailer brakes Electric brakes and manual automatic or surge type brakes are safe if installed properly and adjusted to the manufacturer s specifications The trailer brakes must meet local and Federal regulations Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase The braking system of the tow vehicle is rated for operation at the GVWR not GCWR Trailer lamps Trailer lamps are required on most towed vehicles Make sure your trailer lamps conform to local and Federal regulations See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps 165 Driving Never connect any trailer lighting to the vehicle s taillamp circuits because it may damage the electrical system resulting in fire Contact your local Ford dealership for assistance in proper trailer tow wiring installation Additional electrical equipment may be required Using a step bumper The rear bumper is equipped with an integral hitch and requires only a ball with a 19 mm 8 4 inch shank diameter The bumper has a 1 590 kg 3 500 lb trailer weight and 159 kg 850 lb
119. hases The first display will indicate the oil change status OK SOON REQUIRED The second display will indicate the percentage of oil life remaining The display OIL TEMP SIGNAL ERROR indicates a problem with the system Following this display contact your dealer or qualified service technician for system maintenance Operating the message center during system check The message center controls can be operated as follows during the system check sequence 1 Press the system check controls to advance to the next display 2 Press the reset control to immediately conclude the system check 3 Press the range fuel status or fuel economy control to conclude the system check and display the requested feature 4 Press the metric English control to conclude the system check and change the previous display to the new mode 5 Press the oil change reset control to conclude the system check and begin the oil change reset procedure An oil change is recommended whenever indicated by the message center Use only recommended engine oils The message center will tell you the percent of oil life left during system check This percentage is based on your driving history and the time since your last oil change In order to ensure accurate oil life left indications you should only perform the following procedure after you have the oil changed Oil change reset Press the OIL CHANGE RESET control to reset the oil life feature to 100 or your
120. he SecuriLock ignition key Spare SecuriLock keys can be purchased from your dealership and programmed to your SecuriLock passive anti theft system Refer to Programming spare SecuriLock keys for more information If one or both of your SecuriLock keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle bring your vehicle and all available SecuriLock keys to your dealership for reinitialization 113 Controls and features Theft indicator The theft indicator on the instrument cluster will operate as follows e When the ignition is OFF the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock system is protecting your vehicle e When the ignition is turned to RUN or START the theft indicator will light for 3 seconds and then go out If the theft indicator stays on for an extended period of time or flashes rapidly have the system serviced by your dealership or a qualified technician Programming spare SecuriLock keys Spare SecuriLock keys can be purchased from your dealership and programmed to your SecuriLock passive anti theft system up to a total of 8 keys Your dealership can program your new SecuriLock key s to your vehicle or you can do it yourself using the following simple procedure To program a new SecuriLock key yourself you will need two previously programmed SecuriLock keys keys that already operate your veh
121. he manufacturer of your child safety seat for information about ordering a tether strap 137 Seating and safety restraints Tether anchorage hardware A tethered seat can be installed in the front seat Put the tether strap over the seatback and attach it to an anchor bracket An anchor bracket can be installed on the rear edge of the front seat cushion The provision attaching hole is provided in the rear edge of the front passenger seat cushion frame The anchorbracket must be installed using the instructions provided with the kit Tether anchorage hardware kits part number 613D74 including instructions may be obtained at no charge from any Ford or Lincoln Mercury dealer Tighten the anchor according to specifications Otherwise the safety seat may not be properly secured and the child may be injured in a sudden stop or collision 138 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine avoid pressing the accelerator before or during starting Only use the accelerator when you have difficulty starting the engine For more information on starting the vehicle refer to Starting the engine in this chapter Extended idling at high engine speeds can produce very high temperatures in the engine
122. hills e additional engine braking is desired If towing a trailer refer to Driving while you tow in the Trailer Towing chapter To return to Overdrive mode press the transmission control switch The TCIL will no longer be illuminated Each time the vehicle is started the transmission will automatically return to normal overdrive mode 2 Second Use 2 Second to start up on slippery roads or to provide P RN D 2 EE A E E 5 downgrades Transmission operates in third gear 1 First Use 1 First to provide maximum O downgrades Upshifts can be made by shifting to 2 Second or to Overdrive Selecting 1 Low at higher speeds causes the transmission to shift to a lower gear and will shift to 1 First after the vehicle decelerates to the proper vehicle speed 151 Driving Forced Downshifts To gain acceleration in Overdrive or Drive O D OFF when passing another vehicle push the accelerator to the floor The transmission will downshift to the appropriate gear fourth third second or first gear FOUR WHEEL DRIVE 4WD OPERATION IF EQUIPPED When Four wheel drive AWD is engaged power is supplied to all four wheels through a transfer case 4WD power can be selected when additional driving power is desired If equipped with the Electronic Shift 4WD System and the instrument panel control is moved to 4WD Low while the vehicle is moving the system will not engage and no damage will occur
123. hird transmitter programmed recall memory position three e the fourth transmitter programmed will not recall a memory position Memory positions can be changed at any time The memory feature can be deactivated or reactivated by performing the following 1 Make sure the ignition is off and all doors and the liftgate window are closed Turn the ignition key from OFF to ON Press the power door unlock control three times Turn the ignition key from ON to OFF Press the power door unlock control three times Turn the ignition back to ON The horn will chirp 7 Press the unlock control two times then press the lock control The horn will chirp twice if the remote memory seat feature was deactivated or will sound three times two short chirps followed by one long chirp if the feature was activated ao nA W LO 8 Turn the ignition to OFF The horn will chirp once to confirm that you activated or deactivated the remote memory seat feature 107 Controls and features The memory feature will continue to work from the door control even when deactivated at the remote entry module Replacing the battery The transmitter is powered by one coin type three volt lithium battery CR2032 or equivalent Typical operating range will allow you to be up to 10 meters 83 feet away from your vehicle A decrease in operating range can be caused by e weather conditions e nearby radio towers e structures around the vehicle e othe
124. icator will no longer be illuminated 148 Driving Each time the vehicle is started the transmission will automatically return to normal overdrive mode Every time the vehicle is shut off and restarted you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired 2 Second Use 2 Second to start up on slippery roads or to provide P RN D 941 additional engine braking on erg ae downgrades 1 First Use 1 Low to provide maximum O engine braking on steep PRNO21 downgrades Upshifts can be made by shifting to 2 Second or to Overdrive Selecting 1 Low at higher speeds causes the transmission to shift to a lower gear and will shift to 1 Low after vehicle decelerates to the proper speed Driving with a 5 speed automatic transmission if equipped Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P Park to another position If you do not hold the brake pedal down your vehicle may move unexpectedly and injure someone Pull the gearshift lever towards you and downward to move the automatic gearshift P Park Always come to a complete stop O 2 before shifting into or out of P PRN 1 Park Make sure the gearshift is maoae a an a securely latched in P Park This position locks the transmission and prevents the rear wheels from turning 149 Driving Always set the parking brake ful
125. icle s engine If two previously programmed SecuriLock keys are not available one or both of your original keys were lost or stolen you must bring your vehicle to your dealership to have the spare SecuriLock key s programmed 114 Controls and features Procedure to program spare SecuriLock keys to your vehicle New SecuriLock keys must have the correct mechanical key cut for your vehicle Conventional non SecuriLock keys cannot be programmed to your vehicle You will need to have two previously programmed SecuriLock keys and the new unprogrammed SecuriLock key readily accessible for the procedure Please read and understand the entire procedure before you begin 1 Insert the first previously programmed SecuriLock key into the ignition and turn the ignition from OFF to RUN maintain ignition in RUN for at least one second 2 Turn ignition to OFF and remove the first SecuriLock key from the ignition 3 Within five seconds of turning the ignition to OFF insert the second previously programmed SecuriLock key into the ignition and turn the ignition from OFF to RUN maintain ignition in RUN for at least one second but no more than 5 seconds 4 Turn the ignition to OFF and remove the second SecuriLock key from the ignition 5 Within 10 seconds of turning the ignition to OFF insert the unprogrammed SecuriLock key new key into the ignition and turn the ignition from OFF to RUN maintain i
126. if equipped Iluminates momentarily when the ignition is turned to the ON position CHECK and the engine is OFF The light also illuminates when the air SUSP suspension system requires servicing For information refer to Air suspension system in the Driving chapter Speed control This light comes on when either the SET ACCEL or RESUME controls SPEED are pressed It turns off when the CONT speed control OFF control is 10 Instrumentation pressed the brake is applied or the ignition is turned to the OFF position Safety belt warning chime Chimes to remind you to fasten your safety belts For information on the safety belt warning chime refer to the Seating and safety restraints chapter Supplemental restraint system SRS warning chime For information on the SRS warning chime refer to the Seating and safety restraints chapter Key in ignition warning chime Sounds when the key is left in the ignition in the OFF LOCK or ACC position and the driver s door is opened Headlamps on warning chime Sounds when the headlamps or parking lamps are on the ignition is off and the key is not in the ignition and the driver s door is opened GAUGES 11 Instrumentation Speedomeier Indicates the current vehicle speed oo omg 100 80 I 120 a oo00000 Engine coolant temperature gauge Indicates the temperature of the engine coolant At normal operating temper
127. illuminates when the ignition is turned to the ON position and the engine is off If the brake BRAKE warning lamp does not illuminate at this time seek service immediately Also illuminates when the parking brake is engaged Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately Anti lock brake system ABS Momentarily illuminates when the ignition is turned to the ON position and the engine is off If the light ABs remains on continues to flash or fails to illuminate have the system serviced immediately With the ABS light on the anti lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released Turn signal Iluminates when the left or right turn signal or the hazard lights are turned on If one or both of the a o gt indicators stay on continuously or flash faster check for a burned out turn signal bulb Refer to Exterior bulbs in the Maintenance and care chapter Instrumentation High beams Iluminates when the high beam headlamps are turned on D Anti theft system if equipped Refer to SecuriLock passive anti theft system in the Controls and features chapter THEFT Charging system Iluminates when the ignition is turned to the ON position and the engine is off The light also illuminates when the battery is not charg
128. ing properly requiring electrical system service Check gage Illuminates when the engine coolant temperature is high the engine oil CHECK pressure is low or the fuel gauge is GAGE at or near empty The ignition must be in the ON position for this lamp to illuminate The lamp will also illuminate for several seconds after the ignition is turned to the ON position Refer to Engine coolant temperature gauge Engine oil pressure gauge or Fuel gauge in this chapter for more information Four wheel drive low if equipped This light momentarily illuminates when the ignition is turned to ON AWD Illuminates when four wheel drive low is engaged If the light continues LOW to flash have the system serviced Instrumentation Four wheel drive high if equipped This light momentarily illuminates when the ignition is turned to ON AWD Iuminates when four wheel drive high is engaged If the light H IG H continues to flash have the system serviced Door ajar Illuminates when the ignition is in the ON or START position and any DOOR door is open AJAR O D off Iluminates when the ignition is turned to the ON position and O D transmission control switch has been pushed When the light is on OFF the transmission does not shift into overdrive If the light does not come on when the transmission control switch is depressed or if the light flashes when you are driving have your vehicle serviced Check air suspension
129. ing unless the speakers are turned off Refer to Turning speakers on and off Turning the speakers on and off Press to turn all speakers on or off VOLUME MODE N Co lt q SEEK B MEMORY CJC JONG O Using headphones Plug a 3 5 mm headphone not included into the A jack Press the speaker on off control to operate the headphones 74 Controls and features The rear speakers will cut out once the speaker on off control is pressed The front speaker will remain playing for the front passengers Press the control again to deactivate the headphones Mode select Push the MODE control to toggle between AM FM1 FM2 tape CD or CD changer if equipped VOLUME MODE k CoO m lt q SEEK B MEMORY C DC DORMO Memory preset control Push the MEMORY control w successively to allow rear seat VOLUME MODE passengers to scroll through the 6 C C4 memory presets in AM FM1 or FM2 lt q SEEK MEMORY Push the MEMORY control in CD Cc lt changer mode if equipped to advance to the next disc g aO a Seek function e In radio mode press lt q to find the next listenable station down VOLUME MODE the frequency band C C3 e In radio mode press od to find the next listenable station up the SEEK MEMORY frequency band Coa e In tape mode use the SEEK R_S function to access the next B gt or O OMG OO previous Ki selection
130. io station signal can cause FM reception problems Static can be caused on AM stations by power lines electric fences traffic lights and thunderstorms Moving away from an interfering structure out of its shadow returns your reception to normal 79 Controls and features e Station overload Weak signals are sometimes captured by stronger signals when you pass a broadcast tower A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo Audio system warranties and service Refer to the Warranty Guide for audio system warranty information If service is necessary see your dealer or a qualified technician TURN SIGNAL CONTROL e Push down to activate the left turn signal e Push up to activate the right turn signal POSITIONS OF THE IGNITION 1 ACCESSORY allows the electrical accessories such as the radio to operate while the engine is not running 2 LOCK locks the steering wheel automatic transmission gearshift lever and allows key removal 3 OFF shuts off the engine and all accessories without locking the steering wheel 4 ON all electrical circuits operational Warning lights illuminated Key position when driving 5 START cranks the engine Release the key as soon as the engine star
131. lant and water in your vehicle year round in non extreme climates CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid Refer to the Scheduled Maintenance Guide for the service interval schedules If adding fluid is necessary use only MERCON ATF 201 Maintenance and care e 4 0L SOHC V6 engine e 5 0L V8 engine 1 Start the engine and let it run until it reaches normal operating temperature the engine coolant temperature gauge indicator will be near the center of the normal area between H and C 2 While the engine idles turn the steering wheel left and right several times 3 Turn the engine off 4 Check the fluid level in the reservoir 5 The fluid level should be between the MIN and MAX lines Do not add fluid if the level is in this range 7 If the fluid is low add fluid in small amounts continuously checking the level until it reaches the correct operating range Be sure to put the cap back on the reservoir 202 Maintenance and care TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes Your transmission does not consume fluid However the fluid level should be checked if the transmission is not working properly i e if the transmission slips or shifts slowly or if you notice some sign of fluid leakage Automatic transmission fluid expands when warmed To obtain an accurate fl
132. late and deflate rapidly upon activation After air bag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum powder to lubricate the bag or sodium compounds e g baking soda that result from the combustion process that inflates the air bag Small amounts of sodium hydroxide may be present which may irritate the skin and eyes but none of the residue is toxic While the system is designed to help reduce serious injuries it may also cause minor burns abrasions swelling or temporary hearing loss Because air bags must inflate rapidly and with considerable force there is the risk of death or serious injuries such as fractures facial and eye injuries or internal injuries particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment Thus it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control Several air bag system components get hot after inflation Do not touch them after inflation If the air bag is deployed the air bag will not function again and must be replaced immediately If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision The SRS consists of e driver and passenger air bag modules which include the inflators and air bags e one or
133. led based on the temperature selection For added customer comfort the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers FLOOR Allows for maximum heating by distributing outside air through the floor ducts However the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode FLReDEF Distributes outside air through the windshield defroster ducts and the floor ducts Heating and air conditioning capabilities are provided in this mode The air will be heated or cooled based on the temperature selection For added customer comfort the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts If the temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to prevent fogging DEF iY Distributes outside air through the windshield defroster ducts It can be used to clear ice or fog from the windshield If the outside air temperature is about 10 C 50 F or higher the air conditioner will automatically dehumidify the air to prevent fogging OFF Outside air is shut out and the fan will not operate For short periods of time only use this mode to prevent undesirable odors from entering the vehicle Rear fan off Press REAR FAN OFF to turn off the rear console fan This overrides the rear console fan speed control
134. lip Shaft 236 G transmission MERCON V XT 4R70W ATF 1 C or K 5 QM 5 QM Capacities and specifications Ford part name or equivalent Ford specification Ultra Clear Windshield Windshield washer fluid Washer Concentrate C9AZ 19550 AC ESR M17P5 A 1 If your engine coolant is green in color use Ford Premium Cooling System Fluid If your coolant is orange in color use Ford Extended Life Engine Coolant Refer to Adding engine coolant in the Maintenance and Care chapter 2 4 0L vehicles with conventional rear axles are filled with Motorcraft SAE 80W90 Premium Rear Axle Lubricant part number XY 80W90 QL Ford specification WSP M2C197 A 4 0L vehicles with limited slip differentials and all 5 0L applications use rear axles that are filled with Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lubricant part number F1TZ 19580 B Ford specification WSL M2C192 A 4 0L vehicles with limited slip differentials and all 5 0L applications must add 118 ml 4 oz of additive friction modifier C8AZ 19B546 A Ford specification EST M2C118 A to the rear axle whenever the axle has been serviced ENGINE DATA Engine 4 0L SOHC V6 engine 5 0L V8 engine 210 5250 rpm 15 4200 rpm 240 lb ft 3250 rpm 288 Ibs ft 3300 Recommended fuel 7 octane 1 4 2 5 3 6 1 3 7 2 6 5 4 8 Spark plug gap 1 3 1 4 mm 1 3 1 4 mm 0 052 0 056 inch 0 052 0 056 inch ignition system EDIS EDIS T5 237
135. lowing guides and turn the jack handle clockwise until the tire is a maximum of 25 mm 1 inch off the ground e Front e Rear 181 Roadside emergencies To lessen the risk of personal injury do not put any part of your body under the vehicle while changing a tire Do not start the engine when your vehicle is on the jack The jack is only meant for changing the tire e Never use the front or rear differential as a jacking point 8 Remove the lug nuts with the lug wrench 9 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall the lug nuts cone side in until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered 10 Lower the wheel by turning the jack handle counterclockwise 11 Remove the jack and fully tighten the lug nuts in the order shown 12 Stow the flat tire jack and lug wrench Make sure the jack is fastened so it does not rattle when you drive 13 Turn ON the air suspension switch Gf equipped 14 Unblock the wheels 182 Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Do not push start your vehicle You could damage the catalytic converter Batteries contain sulfuric acid which can burn skin eyes and clothing if contacted Do not att
136. luminum wheels Follow these guidelines when using snow tires and chains e Use only SAE Class S chains e Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines e Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work remove the chains to prevent damage to your vehicle e If possible avoid fully loading your vehicle e Remove the tire chains when they are no longer needed Do not use tire chains on dry roads e The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains 212 Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire If you do not use the proper fuel cap the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision The fuel system may be under pressure If the fuel cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the cap Automotive fuels can cause serious injury or death if misused or mishandled Observe the following guidelines when handling automotive fuel Extinguish all smoking materials and any open flames before fueling your vehicle
137. ly and make sure the gearshift is securely latched in P Park A Never leave your vehicle unattended while it is running R Reverse With the gearshift in R Reverse the vehicle will move backward Always come to a complete stop before shifting into and out of R Reverse N Neutral With the gearshift in N Neutral the vehicle can be started and is free to roll Hold the brake pedal down while in this gear Overdrive The normal driving position for the best fuel economy Transmission operates in gears one through five Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever The transmission control indicator light TCIL will illuminate on the instrument cluster 150 P RNO21 PRNO21 fee PRNQ 21 es 0 D ON OFF 4 Driving Drive Not shown on the display Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position The TCIL will illuminate on the instrument cluster Transmission operates in gears one through four Drive provides more engine braking than Overdrive and is useful whenever driving conditions i e city traffic_hilly terrain etc cause the transmission to excessively shift between Overdrive and Drive Also deactivate Overdrive when e driving with a heavy load e towing a trailer up or down steep
138. ming feature This feature will change from the normal state to the non glare active state when bright lights glare reach the mirror When the mirror detects bright light from front or behind it will adjust automatically to minimize glare The mirror will automatically return to the normal position whenever the vehicle is placed in R Reverse when the mirror is in the ON position This helps to ensure a bright clear view in the mirror when backing up 98 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows e Press the top portion of the rocker switch to close e Press the bottom portion of the rocker switch to open One touch down e Press AUTO completely down and release quickly The driver s window will open fully Depress A again to stop window operation NS 99 Controls and features Window lock The window lock feature allows only q the driver to operate the power windows To lock out all the window controls lt WINDOW LOCK except for the driver s press the left side of the control Press the right side to restore the window controls POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors 7 CHILDPROOF DOOR LOCKS When these locks are set the rear doors cannot be opened from the inside The rear doors can be opened from the outside when the doors are unlocked The childproof locks are locat
139. mperature display can be turned off and on by pressing the MODE control on the overhead console The temperature can be displayed in Centigrade or Fahrenheit by pressing the MODE control If the outside temperature falls below 3 3 C 88 F the display will alternate from ICE to the outside temperature at a two second rate for one minute Compass The compass display is contained in the overhead console The vehicle heading is displayed as one of N NE E SE S SW W and NW The compass reading may be affected when you drive near large buildings bridges power lines and powerful broadcast antenna Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy Adjustments may need to be made to the zone and calibration of the compass 90 Controls and features Compass zone adjustment 1 Determine which magnetic zone you are in by referring to the zone map 2 Press and hold the MODE control until VAR appears in the display then release The display should show the current zone number Wy 3 Press the MODE control until the TD desired zone number appears The display will flash and then return to normal operation The zone is now updated 91 Controls and features Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines e Press and hold the MODE control Wy until CAL appears in the display Eacy
140. nd features oooo00000 J Manual heating and air conditioning system DOs Fan speed control Controls the volume of air circulated in the vehicle O 21 Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle YD Mode selector control Controls the direction of the airflow j wv to the inside of the vehicle V AC amp B w The air conditioning compressor will operate in all modes except f and r However the air conditioning will only function if the outside temperature is about 10 C 50 F or above Since the air conditioner removes considerable moisture from the air during operation it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle Under normal conditions your vehicle s climate control system should be left in any position other than MAX A C or OFF when the vehicle is parked This allows the vehicle to breathe through the outside air inlet duct e MAX A C Uses recirculated air to cool the vehicle MAX A C is noisier than A C but more economical and will cool the inside of the vehicle faster Airflow will be from the instrument panel registers This mode can also be used to prevent undesirable odors from entering the vehicle e A C Uses outside air to cool the vehicle It is quieter than MAX A C
141. nd the use of gasolines labeled as Regular that are sold with octane ratings of 86 or lower in high altitude areas Do not be concerned if your engine sometimes knocks lightly However if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating see your dealer or a qualified service technician to prevent any engine damage Fuel quality If you are experiencing starting rough idle or hesitation driveability problems during a cold start try a different brand of Regular unleaded gasoline Premium unleaded gasoline is not recommended particularly in the United States because it may cause these problems to become more pronounced If the problems persist see your dealer or a qualified service technician The American Automobile Manufacturers Association AAMA issued a fuel specification to provide information on high quality fuels that optimize the performance of your vehicle We recommend the use of fuels that meet the AAMA specification if they are available It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel Cleaner air Ford approves the use of gasolines to improve air quality including reformulated gasolines that contain oxygenates up to 10 ethanol or 15 MTBE 215 Maintenance and care Running out of fuel Avoid running out fuel because this situation may have an adverse affect on po
142. nd water If you must drive through high water drive slowly Traction or brake capability may be limited When driving through water determine the depth avoid water higher than the bottom of the hubs if possible and proceed slowly If the ignition system gets wet the vehicle may stall 158 Driving Once through water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal After driving through mud clean off residue stuck to rotating driveshafts halfshafts and tires Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components If the transmission transfer case or front axle are submerged in water their fluids should be checked and changed if necessary Water intrusion into the transmission may damage the transmission If the rear axle is submerged in water the rear axle lubricant should be checked and changed if necessary The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle Rear axle lubricant quantities should not need to be checked unless a leak is suspected Driving on hilly or sloping terrain When driving on a hill avoid driving crosswise or turning on steep slopes You could lose traction and slip sideways Drive straight up straight down or avoid the hill c
143. nds when the radio is turned on and then revert to clock information Anytime that the media is changed new radio station etc the media information will again display for ten seconds before reverting back to the clock In media mode the media information will always be displayed 56 Controls and features Mute mode Press the control to mute the playing media Press the control again to return to the playing media Rear seat controls if equipped The Personal Audio System a N feature of the optional Premium VOLUME MODE AM FM Stereo Cassette Single CD Premium Sound and the MACH e 4 Audio System with AM FM q SEEK B MEMORY Stereo Cassette Single CD allows C D CO front and middle seat passengers to listen to different media sources radio cassette or CD simultaneously However the front and middle seat passengers cannot listen to two different radio stations at the same time To turn on the rear seat controls EW A FN A press the memory preset controls 3 and 5 at the same time The will appear in the display Pressing 3 and 5 at the same time again will turn the rear seat controls off If there is a discrepancy between the rear seat and the front audio controls such as both trying to listen to the same playing media the front audio system will receive the desired selection 57 Controls and features To activate the Personal Audio System press the speaker headphone
144. ol down e Place the provided height adaptors onto the back of the GARAGE control as needed 88 Controls and features e Press the GARAGE control to activate the transmitter Moon roof if equipped You can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle To open the moon roof The moon roof is equipped with an automatic one touch express opening feature Press and release the rear portion of the control To stop motion at any time during the one touch opening press the control a second time To close the moon roof Press and hold the front portion of the control until the glass panel stops moving Once fully closed the rear of the glass panel will appear higher than the front edge To vent To tilt the moon roof into the vent position when the glass panel is closed press and hold the front portion of the control To close the moon roof from the vent position press and hold the rear portion of the control until the glass panel stops moving The moon roof has a sliding shade that can be opened or closed when the glass panel is shut To close the shade pull it toward the front of the vehicle 89 Controls and features Do not let children play with the moon roof They may seriously hurt themselves Electronic compass temperature display if equipped Outside air temperature The outside temperature display is contained in the overhead console The te
145. ompletely Know the conditions on the other side of a hill before driving over the crest When climbing a steep hill start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started This reduces strain on the engine and the possibility of stalling When descending a steep hill avoid sudden braking Shift to a lower gear when added engine braking is desired When speed control is on and you are driving uphill your vehicle speed may drop considerably especially if you are carrying a heavy load If vehicle speed drops more than 16 km h 10 mph the speed control will cancel automatically Resume speed with accelerator pedal If speed control cancels after climbing the hill reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km h 80 mph Automatic transmissions may shift frequently while driving up steep grades Eliminate frequent shifting by shifting out of Overdrive into D Drive 159 Driving Driving on snow and ice An AWD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle Avoid sudden applications of power and quick changes of direction on snow and ice Apply the accelerator slowly and steadily when starting from a full stop When braking apply the brakes as you normally would In order to allow the anti lock brake system ABS to operate properly keep steady pressure on the brake pedal Allow mo
146. ontrol conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle and fuel trim strategy for optimum driveability and performance To begin this process 1 Set your parking brake 2 Put the gearshift in P Park turn off all accessories and start the engine 3 Let the engine idle for at least one minute 4 The relearning process will automatically complete as you drive the vehicle e The vehicle may need to be driven 16 km 10 miles or more to relearn the idle and fuel trim strategy e If you do not allow the engine to relearn its idle trim the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned If the battery has been disconnected or a new battery has been installed the clock and the preset radio stations must be reset once the battery is reconnected 207 Maintenance and care e Always dispose of automotive dows batteries in a responsible manner s S Follow your local authorized YW A standards for disposal Call your t local authorized recycling center to find out more about recycling automotive batteries RECYCLE WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades Checking the wiper blades
147. ontrol for rear washer fluid operation a a a Se STEERING WHEEL CONTROLS IF EQUIPPED These controls allow you to operate some radio and climate control features 86 Controls and features Radio control features e Press BAND MODE to select AM FM1 FM2 TAPE or CD if equipped In Radio mode e Press MEM NEXT to select a preset station from memory In Tape mode e Press MEM NEXT to listen to the next selection on the tape In CD mode e Press MEM NEXT to listen to the next track on the disc In any mode e Press VOL up or down to adjust the volume Climate control features e Press TEMP up or down to adjust temperature e Press FAN up or down to adjust fan speed OVERHEAD CONSOLE IF EQUIPPED The appearance of your vehicle s overhead console will vary according to your option package All overhead consoles show the outside temperature and compass display 87 Controls and features Storage compartment if equipped Press the OPEN control to open the storage compartment The door will open slightly and can be moved to full open Installing a garage door opener if equipped The storage compartment can be converted to accommodate a variety of aftermarket garage door openers e Remove the storage clip from the door e Place Velcro hook onto side of aftermarket transmitter opposite of actuator control e Place the transmitter into storage compartment contr
148. own To raise the height of the shoulder belt slide the height adjuster up Pull down on the height adjustment assembly to make sure it is locked in place i Position the shoulder belt height adjuster so that the belt rests across the middle of your shoulder Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision 123 Seating and safety restraints Safety belt extension assembly If the safety belt assembly is too short even when fully extended 20 cm 8 inches can be added to the safety belt assembly by adding a safety belt extension assembly part number 611C22 Safety belt extension assemblies can be obtained from your dealer at no cost Use only extensions manufactured by the same supplier as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for you when fully extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts Conditions of operation The driver s safety belt is not The safety belt warning light buckled before the ignition illuminates for one to two minutes and switch is turned to the ON th
149. place on the side of the road Spare tire information Your vehicle is equipped with a spare tire that must be used for emergencies only The spare tire for your vehicle is not as wide as a regular tire and is designed for emergency use only Replace this tire with a full size tire as soon as possible If your vehicle is equipped with 4WD or AWD a spare tire of a different size than the road tires should not be used Such a tire could result in damage to driveline components and make the vehicle difficult to control Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations Spare tire Under the vehicle just in front of the rear bumper Jack lug nut wrench Left rear quarter panel behind interior trim Jack handle Removing the spare tire 1 Insert the jack handle into the rear bumper opening The handle will stop moving and forward resistance to turning will be felt when properly engaged 2 Turn the handle counterclockwise until tire is lowered to the ground the tire can be slid rearward and the cable is slightly slack 3 Remove the retainer from the spare tire 178 Roadside emergencies Stowing the spare 1 Lay the tire on the ground with the valve stem facing up 2 Slide the wheel under the vehicle and install the retainer through the wheel center 3 Turn the jack handle clockwise until the tire is raised to its original position unde
150. properly wear their safety belts even when an air bag SRS is provided It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the outside shoulder only Never wear the shoulder belt under the arm 2 Never swing the safety belt around your neck over the inside shoulder 3 Never use a single belt for more than one person Combination lap and shoulder belts 1 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming ger from until you hear a snap and feel a C it latch Make sure the tongue is x securely fastened in the buckle oO 120 Seating and safety restraints 2 To unfasten push the release button and remove the tongue from the buckle The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts The front and rear seat passenger outboard safety belts have two types of locking modes described below Vehicle sensitive mode The vehicle sensiti
151. r type engine and rear axle ratio 2 Weigh your vehicle as you customarily operate the vehicle without cargo To obtain correct weights try taking your vehicle to a shipping company or an inspection station for trucks 3 Subtract your loaded vehicle weight from the maximum GCWR on the following charts This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart DRIVING THROUGH WATER Do not drive quickly through standing water especially if the depth is unknown Traction or brake capability may be limited and if the ignition system gets wet your engine may stall Water may also enter your engine s air intake and severely damage your engine If driving through deep or standing water is unavoidable proceed very slowly Never drive through water that is higher than the bottom of the hubs 162 Driving Once through the water always try the brakes Wet brakes do not stop the vehicle as effectively as dry brakes Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal Driving through deep water where the transmission is submerged may allow water into the transmission and cause internal transmission damage TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package Trailer towing puts additional loads on your vehicle s engine transmission axle brakes tir
152. r vehicles parked next to the vehicle To replace the battery 1 Twist a thin coin between the two halves of the transmitter near the key ring DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART 2 Place the positive side of new battery in the same orientation Refer to the diagram inside the transmitter unit 3 Snap the two halves back together 108 Controls and features Replacing lost transmitters Take all your vehicle s transmitters to your dealer if service is required If you purchase additional transmitters up to four may be programmed perform the following procedure To reprogram the transmitters yourself place the key in the ignition and turn from OFF to ON eight times in rapid succession within 10 seconds ending in ON After doors lock unlock press any control on all transmitters up to four When completed turn the ignition to OFF The doors will lock unlock one last time to confirm completion of program mode All transmitters must be programmed at the same time Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s or sound the personal alarm The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position The dome lamp control Cif equipped must not be set to the OFF position for the illuminated entry system to operate The inside lights will not turn off if e they have b
153. rates the following features e air vents e audio system controls e rear seat climate controls e cupholders 102 Controls and features CENTER ARMREST REAR CUPHOLDER Do not attempt to raise the console armrest when the rear cupholder is in use If you find resistance when raising the armrest make sure the cupholder is fully closed or else damage may occur to the armrest POSITIVE RETENTION FLOOR MAT To install floor mats 1 Move the driver s seat to the most rearward position 2 Position the driver s side floor mat with the rear of the mat against left outboard front edge of seat track mounting bracket 3 Use a screwdriver to screw locator post into vehicle carpeting Exert pressure while turning to pierce the carpeting When installed properly the locator will not screw down tightly but will rotate freely Use only Ford original Equipment floor mats Do not stack multiple floor mats over the Ford original equipment floor mats as they are not positively retained REAR LIFTGATE The liftgate area is only intended for cargo not passengers You can open and close the liftgate from outside the vehicle It cannot be opened from inside the cargo area e To open the liftgate window C_D unlock the liftgate with the key or power door locks and push the key lock cylinder 2 To open the liftgate unlock the liftgate and pull up on the handle under the license plate lamp shield
154. re stopping distance and drive slower than usual Consider using one of the lower gears TRACTION LOK AXLE IF EQUIPPED This axle provides added traction on slippery surfaces particularly when one wheel is on a poor traction surface Under normal conditions the Traction Lok axle functions like a standard rear axle Extended use of other than the manufacturer s specified size tires on a Traction Lok rear axle could result in a permanent reduction in effectiveness This loss of effectiveness does not affect normal driving and should not be noticeable to the driver To avoid injury never run the engine with one wheel off the ground such as when changing a tire VEHICLE LOADING Before loading a vehicle familiarize yourself with the following terms e Base Curb Weight Weight of the vehicle including any standard equipment fluids lubricants etc It does not include passengers or aftermarket equipment e Payload Combined maximum allowable weight of cargo passengers and optional equipment The payload equals the gross vehicle weight rating minus base curb weight e GVW Gross Vehicle Weight Base curb weight plus payload weight The GVW is not a limit or a specification 160 Driving e GVWR Gross Vehicle Weight Rating Maximum total weight of the base vehicle passengers optional equipment and cargo The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver s door pillar
155. rn the ignition key from RUN ACC to OFF 4 Press the power door UNLOCK control three times 5 Turn the ignition key from OFF to RUN ACC A horn chirp indicates the enable disable feature is entered 6 Press the power door UNLOCK control one time 7 Press the power door LOCK control to toggle the Autolock Relock state You will receive a horn chirp followed by either a long honk autolock relock is enabled or no honk autolock relock is disabled 8 Turn ignition to OFF 110 Controls and features If autolock relock has been changed the horn will chirp to confirm procedure is complete Keyless entry system if equipped With the keyless entry keypad you CACA 5 6 7 8 9 0 e lock or unlock the vehicle doors without using the key e activate deactivate the autolock feature See also Remote entry system in this chapter for more information Your vehicle has a factory set 5 digit code that operates the keyless entry system You can also program your own 5 digit personal entry code The factory set code is located e on the owner s wallet card in the glove compartment e taped to the computer module When pressing the controls on the keyless entry keypad press the middle of the controls to ensure a good activation Programming your own personal entry code 1 Enter the factory set code keypad will illuminate when pressed 2 Press the 1 2 control within five seconds of step 1
156. rneath the vehicle The jack handle ratchets when the tire is raised to the stowed position It will not allow you to overtighten Tire change procedure To prevent the vehicle from moving when you change a tire be sure the parking brake is set then block Gin both directions the wheel that is diagonally opposite other side and end of the vehicle to the tire being changed If the vehicle slips off the jack you or someone else could be seriously injured On vehicles equipped with Air Suspension turn OFF the Air Suspension switch prior to jacking hoisting or towing your vehicle Refer to the instruction sheet for detailed tire change instructions 1 Park on a level surface activate hazard flashers and set the parking brake 2 Place gearshift lever in P Park and turn engine OFF 179 Roadside emergencies When one of the rear wheels is off the ground the transmission alone will not prevent the vehicle from moving or slipping off the jack even if the transmission is in P Park 3 Block the diagonally opposite wheel A A D ae 4 Use the tip of the lug wrench to V The E PR remove any wheel trim 5 Loosen each wheel lug nut but do not remove them until the wheel is raised off the ground 180 Roadside emergencies 6 Turn OFF the air suspension switch Gf equipped Refer to Air suspension system in the Driving chapter 7 Position the jack according to the fol
157. rnings that come with any infant or child restraint you might use When possible place children in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Children and safety belts If the child is the proper size restrain the child in a safety seat Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit 132 Seating and safety restraints Do not leave children unreliable adults or pets unattended in your vehicle To improve the fit of lap and shoulder belts on children who have outgrown child safety seats Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards Belt positioning booster seats raise the child and provide a shorter firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child A bel
158. rol or the AM FM control or the beginning of the tape is reached Fast forward The fast forward control works in tape mode e In the tape mode tape direction will automatically reverse when the end of the tape is reached Tape direction select Press SIDE and 1 2 at the same time to play the alternate side of a tape Eject function Press the control to stop and eject a tape E J Dolby noise reduction Dolby noise reduction operates only in tape mode Dolby reduces __ _ gt the amount of hiss and static during tape playback 39 Controls and features Press the DA control to activate and deactivate Dolby noise reduction The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation Setting the clock To set the hour press and hold the CLK control and press e lt q to decrease hours and gt to increase hours To set the minute press and hold the CLK control and press 40 Controls and features o e p to increase minutes AM FM Stereo Single CD Radio VOL PUSH ON Or CEE craton l Volume power control Press the control to turn the audio VOL PUSH ON system on or off C 41 Controls and features Turn the control to raise or lower K DN volume VOL PUSH ON If the volume is set above a certain level and the ignition is turned off the volume will come b
159. ry has been cleaned or replaced For longer trouble free operation keep the top of the battery clean and dry Also make certain the battery cables are always tightly fastened to the battery terminals If you see any corrosion on the battery or terminals remove the cables from the terminals and clean with a wire brush You can neutralize the acid with a solution of baking soda and water Batteries normally produce explosive gases which can cause personal injury Therefore do not allow flames sparks or lighted substances to come near the battery When working near the battery always shield your face and protect your eyes Always provide proper ventilation 206 Maintenance and care When lifting a plastic cased battery excessive pressure on the end walls could cause acid to flow through the vent caps resulting in personal injury and or damage to the vehicle or battery Lift the battery with a battery carrier or with your hands on opposite corners Keep batteries out of reach of children Batteries contain sulfuric acid Avoid contact with skin eyes or clothing Shield your eyes when working near the battery to protect against possible splashing of acid solution In case of acid contact with skin or eyes flush immediately with water for a minimum of 15 minutes and get prompt medical attention If acid is swallowed call a physician immediately Because your vehicle s engine is electronically controlled by a computer some c
160. s not 1 2 3 4 5 6 necessary to first enter the keypad code 112 Controls and features SECURILOCK PASSIVE ANTI THEFT SYSTEM The SecuriLock passive anti theft system provides an advanced level of vehicle theft protection Your vehicle s engine can only be started with the two special SecuriLock electronically coded keys provided with your vehicle Each time you start your vehicle the SecuriLock key is read by the SecuriLock passive anti theft system If the SecuriLock key identification code matches the code stored in the SecuriLock anti theft system the vehicle s engine is allowed to start If the SecuriLock key identification code does not match the code stored in the system or if a SecuriLock key is not detected vehicle theft situation the vehicle s engine will not operate The SecuriLock passive anti theft system is not compatible with aftermarket remote start systems Use of these systems may result in vehicle starting problems and a loss of security protection Large metallic objects or devices such as the Mobil Speedpass on the same key ring as your SecuriLock key may cause vehicle starting problems These objects and devices cannot damage the SecuriLock key but can cause a momentary problem if they are too close to the key when starting the engine If a problem occurs turn ignition off and restart the engine with all other objects on the key ring held away from t
161. scheduled maintenance Occasional brake noise is normal and often does not indicate a performance concern with the vehicle s brake system In normal operation automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied Such noises are usually heard during the first few brake applications in the morning however they may be heard at any time while braking and can be aggravated by environmental conditions such as cold heat moisture road dust salt or mud If a metal to metal continuous grinding or continuous squeal sound is present while braking the brake linings may be worn out and should be inspected by a qualified service technician Anti lock brake system ABS On vehicles equipped with an anti lock braking system ABS a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel bumps wet or snowy roads is normal and indicates proper functioning of the vehicle s anti lock brake system The ABS performs a self check at 17 km h 10 mph after you start the engine and begin to drive away A brief mechanical noise may be heard during this test This is normal If a malfunction is found the ABS warning light will come on If the vehicle has continuous vibration or shudder in the steering wheel while braking the vehicle should be
162. sette Single CD allows front and middle seat passengers to listen to different media sources radio cassette or CD simultaneously However the front and middle seat passengers cannot listen to two different radio stations at the same time To turn on the rear seat controls press the memory preset controls 3 and 5 at the same time The will appear in the display Pressing 3 and 5 at the same time again will turn the rear seat controls off If there is a discrepancy between the rear seat and the front audio controls such as both trying to listen to the same playing media the Controls and features a VOLUME MODE Sen 7 lt q SEEK B MEMORY Coa E Logg k front audio system will receive the desired selection To activate the Personal Audio System press the speaker headphone control Press the MODE control to change audio sources for headphone mode only Use the SEEK VOLUME and MEMORY controls to make adjustments to the playing media Eo A VOLUME MODE CD lt q SEEK gt MEMORY e CEC Jao 6 73 Controls and features Adjusting the volume i VOLUME MODE CJC lt q SEEK gt MEMORY C n0 gt Oa 090 J Press the control to increase volume owes MODE N Press the control to decrease C volume a SEEK gt MEMORY C DC DORO x From the rear seat controls volume control can be set no higher than the current radio sett
163. spect the fluid level 3 If necessary add brake fluid until the level reaches MAX Do not fill above this line 4 Use only a DOT 3 brake fluid certified to meet Ford specifications Refer to Lubricant specifications in the Capacities and specifications chapter 197 Maintenance and care i Brake fluid is toxic If you use a brake fluid that is not DOT 3 you will cause permanent damage to your brakes Do not let the reservoir for the master cylinder run dry This may cause the brakes to fail WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel The reservoir is highlighted with a G7 symbol If the level is low add enough fluid to fill the reservoir In very cold weather do not fill the reservoir all the way Do not put engine coolant in the container for the windshield washer fluid Checking and adding washer fluid for the liftgate Washer fluid for the liftgate is supplied by the same reservoir as the windshield 198 Maintenance and care ENGINE COOLANT Check the level of the engine coolant in the reservoir Refer to the Scheduled Maintenance Guide for service interval schedules Be sure to read and understand Precautions when servicing your vehicle in this chapter If the engine coolant has not been checked at the recommended interval the engine coolant reservoir may become empty If this occurs add engine coolant to the reservoir
164. strumentation Selectable features English metric display Press to toggle the message center display between metric or English units Fuel range Press once to display the approximate kilometers miles left to drive before the fuel tank is empty Press again to display the distance driven since this function was last manually reset For maximum accuracy of this display feature the ignition should be in the OFF position during fueling The display FUEL LEVEL ERROR indicates a problem with the fuel indication system See your dealer or qualified service technician for system maintenance Fuel status Press once to display the approximate amount of fuel remaining in the fuel tank Press again to display the approximate amount of fuel used since the system was last reset 16 Instrumentation Fuel economy Press to display your vehicle s average fuel economy in liters 100 km or miles gallons Reset Press the reset control to reset the current feature being displayed Warnings distance driven average fuel economy fuel used and personalized oil reset percentage are the only features that respond to reset System check Press the system check control to display the status of the following systems e engine oil life left e engine oil level e voltage level e engine coolant temperature e washer fluid level e fuel level 17 Instrumentation The engine oil life left has two p
165. submerged in water their fluids should be checked and changed if necessary Water intrusion into the transmission may damage the transmission If the rear axle is submerged in water the rear axle lubricant should be checked and changed if necessary The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle Rear axle lubricant quantities should not need to be checked unless a leak is suspected Driving on hilly or sloping terrain When driving on a hill avoid driving crosswise or turning on steep slopes You could lose traction and slip sideways Drive straight up straight down or avoid the hill completely Know the conditions on the other side of a hill before driving over the crest When climbing a steep hill start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started This reduces the strain on the engine When descending a steep hill avoid sudden braking Shift to a lower gear when added engine braking is desired 156 Driving When speed control is on and you are driving uphill your vehicle speed may drop considerably especially if you are carrying a heavy load If vehicle speed drops more than 16 km h 10 mph the speed control will cancel automatically Resume speed with accelerator pedal If speed control cancels after climbing the hill reset speed by pressing and holding the SET ACCEL button
166. sult in severe personal injuries in the event of a collision Refer to Cleaning and maintaining the safety belts in the Maintenance and care section AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM SRS 125 Seating and safety restraints Important supplemental restraint system SRS precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module YIM All occupants of the vehicle including the driver should always properly wear their safety belts even when air bag SRS is provided Always transport children 12 years old and under in the back seat and always use appropriate child restraints NHTSA recommends a minimum distance of at least 25 cm ten 10 inches between an occupant s chest and the air bag module Steps you can take to properly position yourself away from the airbag e Move your seat to the rear as far as you can while still reaching the pedals comfortably e Recline the seat slightly one or two degrees from the upright position Do not put anything on or over the air bag module Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury 126 S
167. t cehvseausshauntvbacentavtdeccta 231 plastic parts serisini ien 230 WASHING siroa a 227 MAXIME seamstress 228 wheels eceecccceeessecesesseeseseesees 229 WINGOWS sessirnir rinsi 232 wiper blades cccscccceeeseees 230 woodtone trim 0 232 Compass electronic ccccee 90 CalibYalOM ccicciseeaccaiedidevenc ele 92 set zone adjustment 91 CONSOLE perissicscrsdeiesntecesaeveegs 101 102 OVETHEAG carere 87 88 TOAD E EE E A 102 Controls POWEY S al sesoses 116 118 Coolant 455 cessssancssesiieeweictesees 201 checking and adding 199 refill capacities ceee 201 Defrost rear WINKOW ccceccceesseceeeeseeees 31 Driveline universal joint and SLIP YOKE seeraniimitismarerirsne 205 Driving under special CONCITIONS seisseen 156 159 SANG eeren eT 156 158 snow and ice 155 157 158 160 through water e s 156 158 Emission control system 221 Engine check engine service engine SOOM LSE sscis secscsteeseedbocsseane Gseese 6 CHOLA eae hoor tatoos 199 idle speed control 206 service points wee 193 194 starting after a collision 169 Engine block heater 141 Engine oil checking and adding 196 GIDSLICK etvesccinssocccivsses i etscdeests 194 specifications 194 196 Exhaust fumes cccceceseeees 142 Floor Mats serres 103 Four Wheel Drive VENICIES Aian 9 10 152 CONELO tLAC eeeeceeeseeeetteeees 1
168. t lean your head on the door the side air bag could injure you as it deploys from the side of the seatback Do not attempt to service repair or modify the air bag Supplemental Restraint System its fuses or the seat cover on a seat containing an air bag See your Ford or Lincoln Mercury dealer 129 Seating and safety restraints All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided How does the side air bag system work The side air bag system consists of the following e An inflatable nylon bag air bag with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks A special seat cover designed to allow airbag deployment e The same warning light electronic control and diagnostic unit as used for the front air bags e Two crash sensors located under the outboard side of the front seats attached to the floor Side air bags in combination with seat belts can help reduce the risk of severe injuries in the event of a significant side impact collision The side air bags are fitted on the outboard side of the seatbacks of the front seats In certain lateral collisions the air bag on the side affected by the collision will be inflated even if the respective seat is not occupied The air bag was designed to inflate between the door panel and occupant to further enhance the protection provided
169. t positioning booster should be used if the shoulder belt rests in front of the child s face or neck or if the lap belt does not fit snugly on both thighs or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion You may wish to discuss the special needs of your child with your pediatrician SAFETY SEATS FOR CHILDREN gt i CI an VL Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision 133 Seating and safety restraints When installing a child safety seat e Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter e Use the correct safety belt buckle for that seating position Insert the belt tongue into the proper buckle until you hear a snap and feel it latch Make sure the tongue is securely fastened in the buckle e Keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling Place seat back in upright position e Put the safety belt in the automatic locking mode
170. t use household or glass cleaners These agents can stain and discolor the fabric Use a mild soap and water solution if necessary Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets Do not bleach or dye the belts because these actions may weaken the belt webbing Check the safety belt system periodically to make sure there are no nicks wear or cuts If your vehicle has been involved in an accident refer to the Safety belt maintenance section in the Seating and safety restraints chapter Cleaning leather seats if equipped To clean simply use a soft cloth dampened with water and a mild soap Wipe the leather again with a damp cloth to remove soap residue Dry with a soft cloth For tougher soiling concerns Ford recommends using the leather cleaning kit F8AJ 19G253 AA which is available from your Ford Dealer This mild cleaner and special pad cleans the leather and maintains its natural beauty Follow the instructions on the cleaner label Regular cleaning of your leather upholstery helps maintain its resiliency and color Do not use household cleaning products alcohol solutions solvents or cleaners intended for rubber vinyl or plastics 231 Maintenance and care Woodtone trim Wipe stains with a soft cloth and a multi purpose cleaning solution Inside windows Use glass cleaner for the inside windows if they become fogged Cleanin
171. th a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation Cassette and casseite player care e Use only cassettes that are 90 minutes long or less e Do not expose tapes to direct sunlight high humidity extreme heat or extreme cold Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing e Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub e Remove loose labels before inserting tapes e Do not leave tapes in the cassette player for a long time when not being played Radio frequency information The Federal Communications Commission FCC and the Canadian Radio and Telecommunications Communications CRTC establish the frequencies AM and FM stations may use for their broadcasts Allowable frequencies are AM 530 540 1600 1610 kHz FM 87 9 88 1 107 1 107 9 MHz Not all frequencies are used in a given area Radio reception factors Three factors can affect radio reception e Distance strength The further an FM signal travels the weaker it is The listenable range of the average FM station is approximately 40 km 24 miles This range can be affected by signal modulation Signal modulation is a process radio stations use to increase their strength volume relative to other stations e Terrain Hills mountains and tall buildings between your vehicle s antenna and the rad
172. the AM FM select controls 2 Press the AUTO control 3 When the first six strong stations jA are filled the station stored in F memory preset control 1 will start playing If there are less than six strong stations available on the frequency band the remaining memory preset controls will all store the last strong station available To deactivate autoset and return to your audio system s manually set memory stations press the AUTO control again 65 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system s bass output Press the BASS control then press lt to decrease bass output and gt to increase bass output Treble adjust The treble adjust control allows you to increase or decrease the audio system s treble output Press the TREB control then press lt to decrease treble output and gt to increase treble output Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers 66 Controls and features Press the BAL control then press e lt q to shift sound to the left and e to shift sound to the right Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers Press the FADE control then press lt to shift sound to the front gt to shift sound to the rear Tape CD CD changer if equipped select e To be
173. the CD changer other types will damage the unit Keep the CD changer door closed Coins and foreign objects will damage the CD player and void your audio system warranty Troubleshooting the CD changer if equipped The laser beam used in the compact disc player is harmful to the eyes Do not attempt to disassemble the case If sound skips e You may be traveling on a rough road playing badly scratched discs or the disc may be dirty Skipping will not scratch the discs or damage the player If your changer does not work it may be that e A disc is already loaded where you want to insert a disc e The disc is inserted with the label surface downward e The disc is dusty or defective e The player s internal temperature is above 60 C 140 F Allow the player to cool down before operating A disc with format and dimensions not within industry standards is inserted Cleaning compact discs Inspect all discs for contamination before playing If necessary clean discs only with an approved CD cleaner and wipe from the center out to the edge Do not use circular motion CD and CD changer care e Handle discs by their edges only Never touch the playing surface e Do not expose discs to direct sunlight or heat sources for extended periods of time e Do not insert more than one disc into each slot of the CD changer magazine 78 Controls and features Cleaning cassetie player if equipped Clean the tape player head wi
174. the simple calculations in order to determine fuel economy Multiply liters used by 100 then divide by total kilometers traveled Divide total miles traveled by total gallons used Keep a record for at least one month and record the type of driving city or highway This will provide an accurate estimate of the vehicle s fuel economy Additionally keeping records during summer and winter will show how temperature impacts fuel economy In general lower temperatures give lower fuel economy Driving style good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy 218 Maintenance and care Habits Smooth moderate operation can yield up to 10 savings in fuel Steady speeds without stopping will usually give the best fuel economy Idling for long periods of time greater than one minute may waste fuel Anticipate stopping slowing down may eliminate the need to stop Sudden or hard accelerations may reduce fuel economy Slow down gradually Drive at reasonable speeds traveling at 105 km h 65 mph uses 15 more fuel than traveling at 88 km h 55 mph Revving the engine before turning it off may reduce fuel economy Use of the air conditioner or defroster may reduce fuel economy Use of speed control if equipped may improve fuel economy Speed control can help maintain a constant speed and reduce speed chan
175. ther flash or stay lit e The readiness light will not illuminate immediately after ignition is turned on If either of these indications occur even intermittently have the SRS serviced at your dealership or by a qualified technician immediately Unless serviced the system may not function properly in the event of a collision Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles see your local dealership or qualified technician Air bags MUST BE disposed of by qualified personnel 131 Seating and safety restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children Also see Air Bag Supplemental Restraint System SRS in this chapter for special instructions about using air bags Important child restraint precautions You are required by law to use safety restraints for children in the U S and Canada If small children ride in your vehicle generally children who are four years old or younger and who weigh 18 kg 40 lbs or less you must put them in safety seats made especially for children Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and wa
176. tion 80 Lamps daytime running light 20 FOS VANS eiscessssccsseuderscessennesrseeeds 20 headlamps ccesecceeesseeeeesseeees 20 headlamps flash to pass 21 instrument panel dimming 21 replacing bulbs 222 223 224 225 226 Lane change indicator see Turn signal c eee 80 APTS ALES sasinen 103 Lights warning and indicator air DAG aisseiieecszesevaccascteesanaetasecisetes ff anti lock brakes ABS 8 anti theft oo ccccessceeesseeeeeens 9 Drake ogenen GE 8 charging SySteM sesrosrissnaiine 9 check coolant ceeeees 9 cruise indicator sawisrisurscsi 10 door ajar csscieseescencep ddsanneencaas tees 10 f el reset eree en ersi EER 7 Overdrive Off peceni 10 safety Delt sareren raeas 8 speed Control srrerisisiiiscss 84 turn signal indicator 8 Locks childproof ooo eeeeeeeeeeeees 100 Lumbar support seats 116 Message center eee 15 16 Index economy button c eee 17 english metric button 16 reset PULTON ceeeeeeereees 17 system check button 17 18 Mirrors automatic dimming rearview TOULLOL sorser rn s i ie arane 98 cleaning sisceveneetesstiadtngincstenress 232 heated sisccvssesvvivsssenciessvewesStavssess 101 side view mirrors power 101 MOO TOOL soenoe ea 89 Motorcraft parts serscnrineias 217 Octane rating 2 eee 215 Odometer cccccesss
177. to resume speeds over 50 km h 80 mph Automatic transmissions may shift frequently while driving up steep grades Eliminate frequent shifting by shifting out of Overdrive into D Drive Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle Avoid sudden applications of power and quick changes of direction on snow and ice Apply the accelerator slowly and steadily when starting from a full stop When braking apply the brakes as you normally would In order to allow the anti lock brake system ABS to operate properly keep steady pressure on the brake pedal Allow more stopping distance and drive slower than usual Consider using one of the lower gears ALL WHEEL DRIVE AWD SYSTEM IF EQUIPPED 5 0L ENGINES ONLY Your vehicle is equipped with a full time All Wheel Drive AWD transfer case Power is supplied to all four wheels all the time with no need to shift between two wheel drive and four wheel drive For the lubricant specification and refill capacity of the AWD transfer case refer to Capacities and specifications chapter Utility and four wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low slung sports cars are designed to perform satisfactorily under off road conditions Avoid sharp turns or abrupt maneuvers in these vehicles 157 Driving Driving off road with AWD Your vehicle is
178. to try to scribble it down or pull off the side of the road All you have to do is push a button and begin speaking To record a message 1 Press and release the REC button one time to start recording An audible tone will sound confirming the onset of recording 2 Press and release the REC button a second time to end recording An audible tone will sound again confirming the end of recording and the red indicator light will turn off 3 While a message is being recorded the indicator light will be a solid red 4 If the message exceeds the available memory space two tones will sound the indicator light will flash amber and recording will end The indicator light will flash amber and an error tone will sound if the REC button is pressed when memory is full 96 Controls and features To play a message 1 Press and release the PLAY button to play the message 2 Press and hold the PLAY button to hear all the messages in consecutive order starting with the most recent 3 If the PLAY button is pressed while a message is being listened to TravelNote will skip to the beginning of the next message 4 During all PLAY functions the indicator light will be a solid green The indicator light will flash amber and an error tone will sound if the PLAY button is pressed but no message is currently in memory To delete a message 1 Press and release the DEL button while listening to a message or
179. ts 80 Controls and features SPEED CONTROL To turn speed control on e Press ON Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km h 80 mph SET ACCEL COAST Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved Do not shift the gearshift lever into N Neutral with the speed control on To turn speed control off e Press OFF or e Turn off the vehicle ignition SET ACCEL COAST Once speed control is switched off the previously programmed set speed will be erased 81 Controls and features To set a speed e Press SET SET ACC SET ACCEL For speed control to operate the speed control must be ON and the vehicle speed must be greater than 48 km h 80 mph If you drive up or down a steep hill your vehicle speed may vary momentarily slower or faster than the set speed This is normal Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill If your vehicle speed is faster than the set speed while driving on a downhill you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed If your vehicle slows down more than 16 km h 10 mph below your set speed on an uphill your speed control will disengage This is normal Pressing RES RSM RESUME will re engage it Do not use the speed control in heavy traffic or on roads that are
180. u the following information about tire grades exactly as the government has written it d Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AAAB C The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics 209 Maintenance and care Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of th
181. uid check drive the vehicle until it is warmed up approximately 30 km 20 miles If your vehicle has been operated for an extended period at high speeds in city traffic during hot weather or pulling a trailer the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking 1 Drive the vehicle 30 km 20 miles or until it reaches normal operating temperature 2 Park the vehicle on a level surface and engage the parking brake 3 With the parking brake engaged and your foot on the brake pedal start the engine and move the gearshift lever through all of the gear ranges Allow sufficient time for each gear to engage 4 Latch the gearshift lever in P Park and leave the engine running 5 Remove the dipstick wiping it clean with a clean dry lint free rag 6 Install the dipstick making sure it is fully seated in the filler tube 7 Remove the dipstick and inspect the fluid level The fluid should be in the designated areas for normal and room temperature Correct fluid level The transmission fluid should be checked at normal operating temperatures 66 C 77 C 150 F 170 F on a level surface The normal operating temperature can be reached after approximately 30 km 20 miles of driving However you can check the fluid without driving if the outside temperatures are above 10 C 50 F If fluid is added at this time an overfill condition could result when the vehicle reaches normal operating temperat
182. ure 203 Maintenance and care The transmission fluid should be in this range if at normal operating temperature 66 C 77 C Do Recon 3 D gt 150 F 170 F The transmission fluid should be in this range if at room temperature 10 C 35 C 50 F 95 F High fluid level Fluid levels above the safe range may result in transmission failure An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage High fluid levels can be caused by an overheating condition Adjusting automatic transmission fluid levels i Before adding any fluid make sure the correct type is used The type of fluid used is normally indicated on the dipstick and or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter Use of a non approved automatic transmission fluid may cause internal transmission component damage If necessary add fluid in 250 mL 1 2 pint increments through the filler tube until the level is correct If an overfill occurs excess fluid should be removed by a qualified technician An overfill condition of transmission fluid may cause shift and or engagement concerns and or possible damage 204 Maintenance and care Checking and adding transfer case fluid 1 Clean the filler plug 2 Remove the filler plug and inspect the fluid le
183. ut of the vehicle Then operate your air conditioner as you would normally When placing objects on top of your instrument panel be careful to not place them over the defroster outlets These objects can block airflow and reduce your ability to see through your windshield Also avoid placing small objects on top of your instrument panel These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system Electronic Automatic Temperature Control EATC system if equipped The EATC system will maintain a selected temperature and automatically control airflow You eg 7 REAR FAN OFF can override automatic operation inne or ra an m w l with any of the override controls the fan speed control or the steering wheel controls Turning the EATC on Press AUTOMATIC any of the override controls or the fan speed control The EATC will only operate when the ignition is in the ON position 24 Controls and features sell Turning the EATC off Press OFF Automatic operation Press AUTOMATIC and select the desired temperature The selected temperature and the word AUTO will appear in the display window The EATC system will either heat or cool to achieve the selected temperature The system will automatically determine fan speed airflow location and if fresh outside air or recircul
184. ve emergency locking mode e This vehicle has a seat belt system with an energy management feature at the front seating positions to help further reduce the risk of injury in the event of a head on collision 122 Seating and safety restraints e This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner This feature is designed to help reduce the belt force acting on the occupant s chest After any vehicle collision the seat belt system at all outboard seating positions except driver which has no automatic locking retractor feature must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly in addition to other checks for proper seat belt system function BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly automatic locking retractor feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder To lower the shoulder belt height push the button and slide the height control d
185. ve mode is the normal retractor mode allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of 8 km h 5 mph or more the combination safety belts will lock to help reduce forward movement of the driver and passengers Automatic locking mode In this mode the shoulder belt is automatically pre locked The belt will still retract to remove any slack in the shoulder belt The automatic locking mode is not available on the driver safety belt When to use the automatic locking mode e When a tight lap shoulder fit is desired e Anytime a child safety seat is installed in a passenger front or outboard rear seating position if equipped Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter 121 Seating and safety restraints How to use the automatic locking mode e Buckle the combination lap and shoulder belt e Grasp the shoulder portion and pull downward until the entire belt is extracted e Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode How to disengage the automatic locking mode Disconnect the combination lap shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensiti
186. vel 3 Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening Use only fluid that meets Ford specifications Refer to the Capacities and specifications chapter DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication Refer to the Scheduled Maintenance Guide for maintenance intervals If the original universal joints are replaced with universal joints equipped with grease fittings lubrication will also be necessary 205 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance free battery which normally does not require additional water during its life of service However for severe usage or in high temperature climates check the battery electrolyte level Refer to the Scheduled Maintenance Guide for the service interval schedules Keep the electrolyte level in each cell up to the level indicator Do not overfill the battery cells If the electrolyte level in the battery is low you can add plain tap water to the battery as long as you do not use hard water water with a high mineral or alkali content If possible however try to only fill the battery cells with distilled water If the battery needs water often have the charging system checked If your battery has a cover shield make sure it is reinstalled after the batte
187. wertrain components If you have run out of fuel e You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine e Your Check Engine light may come on For more information on the Check Engine light refer to the Instrumentation chapter Fuel Filler Cap Your fuel tank filler cap has an indexed design with a one eighth turn on off feature When fueling your vehicle 1 Turn the engine off 2 Carefully turn the filler cap counterclockwise 1 8 of a turn until it stops 3 Pull to remove the cap from the fuel filler pipe 4 To install the cap align the tabs on the cap with the notches on the filler pipe 5 Turn the filler cap clockwise 1 8 of a turn until it stops If the Service Engine Soon Check Engine indicator comes on and stays on when you start the engine the fuel filler cap may not be properly installed Turn off the engine remove the fuel filler cap and reinstall it being careful to align the cap properly If you must replace the fuel filler cap replace it with a genuine Ford or Motorcraft part The customer warranty may be void for any damage to the fuel tank or fuel system if a genuine Ford or Motorcraft fuel filler cap is not used The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and
188. winding slippery or unpaved To set a higher set speed e Press and hold SET SET ACC SET ACCEL Release the control when the desired vehicle speed is reached or Press and release SET SET ACC SET ACCEL Each press will increase the set speed by 1 6 km h 1 mph or Accelerate with your accelerator pedal When the desired vehicle speed is reached press and release SET SET ACC SET ACCEL 82 Controls and features You can accelerate with the accelerator pedal at any time during speed control usage Releasing the accelerator pedal will return your vehicle to the previously programmed set speed To set a lower set speed e Press and hold CST COAST Release the control when the desired speed is reached or e Press and release CST COAST Each press will decrease the set speed by 1 6 km h 1 mph or Depress the brake pedal When the desired vehicle speed is reached press SET SET ACC SET ACCEL To disengage speed control e Depress the brake pedal Disengaging the speed control will not erase the previously programmed set speed 83 Controls and features Pressing OFF will erase the previously programmed set speed SET ACCEL COAST To return to a previously set speed e Press RES RSM RESUME For RES RSM RESUME to operate the vehicle speed must be faster than 48 km h 80 mph Indicator light This light comes on when either the SET ACC SET ACCEL or SPEED RES RSM RE
189. with soap and water Consult a physician immediately if you experience an adverse reaction Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage your vehicle Do not use gasolines containing methanol It can damage critical fuel systems components Vehicles certified to meet California emission standards indicated on the underhood Vehicle Emissions Control Information label are designed to operate on California cleaner burning low sulfur gasolines If you have a California certified vehicle and California cleaner burning gasoline is not available when you refuel your engine should perform adequately However the performance of the emission control devices and systems may be adversely affected In New York and Massachusetts which have adopted California s emission standards without requiring the sale of California cleaner burning gasoline repairs to correct the effects of using non California fuel may not be covered by the emissions warranty Your vehicle was not designed to use fuel or fuel additives with metallic compounds including manganese based compounds containing MMT Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty 214 Maintenance and care Octane recommendations Your vehicle is designed to use Regular unleaded gasoline with an R M 2 octane rating of 87 We do not recomme
190. y a qualified service technician if e Oncoming motorists frequently signal you to deactivate your high beams and your high beams are not activated The headlamps do not seem to provide enough light for clear night vision The headlamp beams are pointed substantially away from a slightly down and to the right position CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance Guide for a list of Ford approved cleaners polishes and waxes Washing your vehicle Wash your vehicle regularly with cold or lukewarm water Never use strong detergents or soap If your vehicle is particularly dirty use a quality car wash detergent Always use a clean sponge washing glove or similar device and plenty of water for best results To avoid spots avoid washing when the hood is still warm immediately after or during exposure to strong sunlight During winter months it is especially important to wash the vehicle on a regular basis Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle Remove any exterior accessories such as antennas before entering a car wash If you have wax applied to the vehicle at a commercial car wash it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield After washing apply the brakes several times to dry them 227 Maintenance and care Waxing your vehicle Wax when w
191. z F F y 2 lt zi S O E T j H 5 z 5 5 a A 5 o P D G Z Q o 5 3 2 A B Q A D 2 oO 2 5 a 5 D z including photocopying recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company Copyright 1998 Ford Motor Company j Introduction ICONS Indicates a safety alert Read the following section on Warnings Indicates vehicle information related to recycling and other environmental concerns will follow Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment Indicates a message regarding child safety restraints Refer to Seating AL and safety restraints for more information Indicates that this Owner Guide contains information on this subject Please refer to the Index to locate Lli the appropriate section which will provide you more information WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others your vehicle and its equipment BREAKING IN YOUR VEHICLE There are no particular breaking in rules for your vehicle During the first 1 600 km 1 000 miles of driving vary speeds frequently This is necessary to give the moving parts a chance to break in Introduction IN

Mercury 1999 Mountaineer Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents