McCulloch PM105 Snow Blower User Manual
Contents
1. 1 1 8 Cabinet Dimensions and Weights sssini eine Probe Gip OP 1 1 1 Section 3 OPERATION 110111 1 4 5 9 9 9 0 9 9 2 4 09 9999929 099962 JOE GG C 1 1 1 0 4 1 3 te 0 E 0 btt i Section 4 PROGRAMMING TOEP T e de lt e IAE E E E A E E EA E Section 5 TROUBLESHOOTING Troubleshooting GUU Gasik EE E Error Codes 1 1 Distributors List Domestic and International Model HHC 990 The Henny Penny humidified holding cabinets are designed to keep hot foods moist while maintaining proper tempera ture The units are electronically controlled for easy use and for consistent operation e Electronically controlled humidity and temperature e Li2. 303 10 11 12 13 14 Y PENNY Global Foodrervice 4 2 CLOCK SET Continued 4 2 Model HHC 990 This mode allows you to program the following SP 1 Fahrenheit celsius SP 2 Lock unlock SP 3 Air temperature setpoint SP 4 Humidity setpoint SP 5 e Proof air temperature SP 6 Proof humidity setpoint SP 7 Out of water tripp point SP 8 Clean water pan setpoint SP 9 e System intialization SP 10 Audio volume 52 11 Audio tone SP 12 Audio effects SP 13 Language options 1 Press and hold the P until LEVEL 2 then CLOCK SET PROG shows in the display 2 Press P hgain then SP PROG shows in display PROG 3 After 5 seconds ENTER CODE shows in display 4 Press and SP 1 TEMP UNITS and OR or C shows in the display A 5 Press the v A to change temperature units DOWN UP 6 Press BJand SP 2 LOCK UNLOCK PROGRAMMING PROG shows in display along with either LOCK or UNLOCK 7 Press v change lock the programming or unlock the DOWN UP programming 8 Press and SP 3 AIRTEMP SETPOINT and the PROG preset cabinet temperature shows in display V A 9 Press v A to change the air temperature setpoint DOWN UP 140 F 60 C minimum 210 F 99 C maximum Y PENNY Global Foodservice 4 3 SPECIAL PROGRAMMING SP 1 Fahrenheit Celsius S
3. NY PENNY Global Foodservice Solutions Henny Penny Humidified Holding Cabinets Model HHC 990 Model HHC 992 Model HHC 993 Model HHC 996 Model HHC 997 Model HHC 998 OPERATOR S MANUAL Y PENNY Model HHC 990 Global Foodservice Solutions LIMITED WARRANTY FOR HENNY PENNY APPLIANCES Subject to the following conditions Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts NEW EQUIPMENT Any part of a new appliance except lamps and fuses which proves to be defective in material or workmanship within two 2 years from date of original installation will be repaired or replaced without charge F O B factory Eaton Ohio or F O B authorized distributor To validate this warranty the registration card for the appliance must be mailed to Henny Penny within ten 10 days after installation REPLACEMENT PARTS Any appliance replacement part except lamps and fuses which proves to be defective in material or workmanship within ninety 90 days from date of original installation will be repaired or replaced without charge F O B factory Eaton Ohio or F O B authorized distributor The warranty for new equipment and replacement parts covers only the repair or replacement of the defective part and does not include any labor charges for the removal and installation of any parts travel or other expenses incidental to the repair or re
4. the operating systems of the unit the panel is located on the top front surface of the cabinet a cleaner used to remove lime deposits in the water pan a device that lets the water drain from the water pan into a shallow pan on the floor the valve should be closed while the unit is in use if humidity 1s desired a device that senses low water levels in the water pan a sensor located outside the cabinet that when inserted into the product communicates the temperature of the product to the control panel the connection where the food probe is inserted in order to communicate with the control panel a device that measures the percentage of humidity inside the cabinet during use a preset moisure level at which the cabinet operates this setting is programmed at the factory but can be changed in the field an electronic light on the control panel the lowest temperature at which a food product can be safely held for human consumption the removeable top part of the cabinet that contains all of the operating system a preset temperature at which a sensor warns the operator that the water pan needs refilled a preset group of setpoints designed for holding specific food products at certain temperature and humidity levels the ON OFF switch that sends electricity to the unit s operating systems this switch does not disconnect the electrical power from the wall to the unit a device that shoots a stream of water under pressure this de
5. 2 Amps 24 0 22 3 13 8 12 0 11 2 11 6 17 3 10 0 8 7 8 3 2T 3 15 8 13 7 16 2 13 3 17 3 24 0 220 13 8 8 7 12 0 8 3 11 6 Phase 1 p pib prod a Volts 60Hz 120 120 208 240 240 220 240 CE 120 208 240 220 240 CE 120 208 240 240 220 240 CE 120 120 120 208 240 240 220 240 CE 220 240 CE Model HHC 990 HHC 993 HHC 992 HHC 996 HHC 997 HHC 998 Se H JY PENNY Global Soitan 2 4 ELECTRICAL CONNECTION 1004 Model HHC 990 H Y PENNY Global Foodservice Solutions 2 5 CABINET DIMENSIONS AND WEIGHTS 31 3 4 24 3 4 806 mm 628 mm 72 1 4 1835 mm HHC 990 Unit Height Vvidth Depth Shipping Weight HHC 993 38 965 mm 24 3 4 628 mm 31 3 4 806 mm 220 Ibs 100 kg HHC 990 72 1 4 1835 mm 24 3 4 628 mm 31 3 4 806 mm 367 Ibs 167 kg HHC 992 76 1930 mm 24 3 4 628 mm 31 3 4 806 mm 493 Ibs 224 kg HHC 998 38 965 mm 27 3 4 705 mm 31 3 4 806 mm 269 Ibs 122 kg HHC 996 72 1 4 1835 mm 27 3 4 705 mm 31 3 4 806 mm 400 lbs 181 kg HHC 997 76 1930 mm 27 3 4 705 mm 31 3 4 806 mm 523 Ibs 237 kg 2 4 303 Model HHC 990 The probe clip is an accessory that may be ordered as an option to hold the food probe vvhen not in use Remove one of the module screws and mount the probe clip with that scre
6. 6 Dels 28 20 30 Y PENNY Global Foodservice Solutions 4 3 SPECIAL PROGRAMMING Continued SP 9 System Initialization Factory Settings SP 10 Audio Volume SP 11 Audio Tone SP 12 Audio Effects SP 13 Language Options 303 Y PENNY Model HHC 990 Olof Foodrervice Solutions 5 1 TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION Product not Doors left open e Keep doors closed except holding temperature to load and serve product Product held too long Hold product only for recom mended times Control temperature set too low Increase air temperature SP 3 in Special Program Mode Door gasket torn or worn e Replace bad door gaskets Cabinet steaming Humidity setpoint too high e Decrease humidity setpoint product soggy SP 4 in Special Program Mode Product dry Humidity setpoint too low Increase humidity setpoint SP 4 in Special Program Mode No water in pan Pour water in water pan Unit not heating e Blown fuse e ChangelS amp fuse Unit not reaching set Doors left open e Keep doors closed except temperature to load and serve product Door gasket torn or worn e Replace bad door gaskets More detailed troubleshooting information is available in the Technical Manual available at www hennypenny com or 1 800 417 8405 or 1 937 456 8405 5 1 703 Model HHC 990 Y PENNY Global Foodrervice Sol 5 2 ERROR CODES AND The display shows the following error codes and w
7. G Continued SP 4 Humidity Setpoint SP 5 Proof Air Temperature Setpoint SP 6 Proof Humidity Setpoint SP 7 Out of Water Trip Point SP 8 Clean Water Pan Setpoint Model HHC 990 Press and SP 9 DO SYSTEM INIT shows in display PROG Press and hold pownintil the display counts down from 3 and the display flashes INIT then INIT DONE This com pletes the initialization and sets the control to factory settings Press and SP 10 AUDIO VOLUME and the volume PROG setting 1 to 10 shows in display Press 1 to test volume V A Press A to change the volume DOWN UP Press and SP 11 AUDIO TONE Hz and the tone PROG setting 50 to 2000 shows in display V A Press to change the tone setting 5 5 DOWN UP Press and SP 12 AUDIO EFFECT and the effect _ PROG setting 0 to 3 shows in display V A Press v change the pattern 01 the tone DOWN UP Press and 13 LANGUAGE and the preset PROG language shows in the display V A Press v A to change to English French German DOWN UP Spanish or Portuguese Press and hold the prog button anytime during programming to exit the Special Programming Mode For more information on the other settings of Special Programming call your local Henny Penny distributor in your area or call Henny Penny Corp at 1 800 417 8405 or 1 937 456 8405 20 21 22 Do 24 23 2
8. MER BUTTON TO SELECT FOR PROGRAMMING followed by USE UPAND DOWN TO CHANGE SELECTED TIMERS scrolls through the display Press the desired timer button 1 15 More than one can be programmed at one time 4 A j Press v A to change the selected timer settings DOWN UP Once timers are set press and hold the P and new timer PROG settings become active and normal operation is resumed Press and hold for 5 seconds and LEVEL 2 then PROG CLOCK SET shows in display After 5 seconds ENTER CODE shows in display CS 1 SET HOUR and the time of day with the hour flashing shows in the display V A Press the A to change the hours DOWN UP 1 4 1 TIMER PROGRAMMING 4 2 CLOCK SET Time of day date and day of the week 303 Model HHC 990 Press and CS 2 SET MINUTE shows in the PROG display vvith the minutes flashing A Press v change the minutes DOWN UP Press and CS 3 SET MONTH shows in the j PROG display along with the date month flashing A V Press v A to change the month DOWN UP Press and CS 4 SET DATE shows in the display PROG with the date flashing Press to change the date DOWN UP Press and CS 5 SET YEAR shows in the display PROG with the year flashing V A Press v A to change the year DOWN UP Press and hold P to exit programming PROG
9. P 2 Lock Unlock SP 3 Air Temperature Setpoint 303 Model HHC 990 10 Press and SP 4 HUMIDITY SETPOINT and the PROG preset humidity setpoint shows in display V A Press v 4 to change the humidity setpoint 0 to 90 Press and SP 5 PROOF AIR TEMP and the preset PROG proofing air temperature shows in display Press V A to change the proofing temperature DOWN 80 F 27 C minimum 140 F 60 C maximum Press and SP 6 PROOF HUMIDITY SETPOINT PROG and the preset proofing humidity shows in display 7 A Press v A to change the proofing humidity 10 to 90 DOWN UP Press and SP 7 OUT OF WATER TRIP POINT and PROG the preset trip point temperature shows in display If the float switch fails the trip point temperature is the water pan tempera ture at which the control senses the water pan is out of water We recommend a trip point temperature of 450 F 232 C 7 Press v A to change the out of water trip point DOWN UP Press and SP 8 CLEAN WATER PAN SETPOINT PROG and the preset temperature at which the controls senses that the water pan needs cleaned of lime shows in the display We recommend a setpoint temperature of 425 F 218 C 7 Press v A to change the setpoint DOWN UP 303 11 12 13 14 15 16 17 18 19 Y PENNY Global Foodrervice Sol 4 3 SPECIAL PROGRAMMIN
10. Press to view the food probe temperature cabinet temperature and humidity date and time if pressed in the Program Mode shows previous settings pressing this along witl accesses PROG the Information Mode which has historic information on the cabinet s performance Used to adjust the value of the currently displayed setting in the Program Mode 303 POWER Switch TEMPERATURE Digital Display Humidity LED HUMIDITY INFO v 4 DOWN UP 1 6 amp 7 3 1 3 1 3 1 3 1 3 1 3 1 Model HHC 990 Used to access the Program Modes once in the Program Mode itis used to advance to the next parameter pressing this along with Daccesses the Information Mode INFO which has historic information on the cabinet s performance After plugging the food probe into the receptacle the meat probe can then be inserted into the product and the product temperature is displayed Once a tray of food is placed in the cabinet the appropriate timer is pressed and the time remaining shows in the display above the timer number once the timer counts down to zero the display flashes 0 00 and the control beeps HHC 990 and 996 have 15 timers and the HHC 993 and 998 have 5 timers 3 2 3 1 3 1 3 1 eE AA OPERATING CONTROLS Continued PROG 9 Food Probe Receptacle 10 Count Down Timers 303 H Y PENNY Model HHC 990 Global Foodkervice Solutions 3 2 OPERATING CONTROLS Contin
11. R CONSEQUENTIAL DAMAGES SHALL BE AVAIL ABLE The above limited warranty does not apply a to damage resulting from accident alteration misuse or abuse b if the equipments serial number is removed or defaced or for lamps and fuses THE ABOVE LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING MERCHANTABILITY AND FITNESS AND ALL OTHER WARRANTIES ARE EXCLUDED HENNY PENNY NEITHERASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY FM05 007 D Revised 10 13 04 VY PENNY Model HHC 990 Page 303 1 1 1 1 1 1 1 1 1 2 2 1 2 1 2 2 2 4 2 5 3 1 3 1 3 4 3 5 3 6 4 1 4 1 4 3 5 1 5 2 Global Foodservice Solutions TABLE OF CONTENTS Section Section 1 INTRODUCTION Ho midified Holdine Cabinet 532282 ccs sasoxannaneoacencacnteaseadassseouaassesiasanconesasauneesactenesaele Ri E REEE EEE PEE T Section 2 INSTALLATION 11 11 4 9 6 6 55 6
12. arnings when a WARNINGS fault is detected along with an alarm sound Both the heat and humidity systems shut down except when specified otherwise Display Panel Board Correction Turn switch to OFF position then back to ON if display still shows E 4 the PC board is getting too hot clean louvers and check cooling fan 11 cooling fan is not working have it replaced once panel cools down the controls should return to normal if E 4 persists have the PC board replaced Turn switch to OFF position then back to ON if display shows E 5 the heating circuits and temperature probe should be checked once the unit cools down the controls should return to normal 11 E 5 persists have the PC board replaced Turn switch to OFF position then back to ON if display shows E 54A the control should be re initialized see Pro gramming Section if the error code persists have PC board replaced Turn switch to OFF position then back to ON if display shows E 54B the control should be re initialized see Pro gramming Section if the error code persists have PC board replaced Turn switch to OFF position then back to ON if the display shows E 6 the temperature probe should be checked once the temperature probe 15 repaired or replaced the controls should return to normal if E 6 persists have the PC board replaced 4 7 4 CPU TOO HOT e Control board too hot unit overheating o
13. d up or empty a device that shoots a stream of water under pressure this type of device should NOT be used to clean a holding cabinet the area in the cabinet that holds water for creating humidity inside the cabinet G 2 VY PENNY Global Foodservice Solutions probe clip product load capacity proof function relative humidity setpoint system initialization temperature setting vent activation switch vented panels water fill line water heater sensor water jet water pan 303
14. ft off doors e Stainless steel construction e Easily maintained e Luift out tray racks e Full perimeter magnetic door seals e Easy access to electrical controls e Food probe supplied to easily display food temperature As in any unit of food service equipment the Henny Penny humidi fied holding cabinet does require care and maintenance Require ments for the maintenance and cleaning are contained in this manual and must become a regular part of the operation of the unit at all times Should you require outside assistance just call your local indepen dent Henny Penny distributor in your area or call Henny Penny Corp 1 800 417 8405 toll free or 1 937 456 8405 1 1 HUMIDIFIED HOLDING CABINET 1 2 FEATURES 1 3 PROPER CARE 1 4 ASSISTANCE 303 Model HHC 990 1 5 SAFETY The Henny Penny Humidified Holding Cabinet has safety features incorporated However to ensure a safe operation read and fully understand the proper installation operation and maintenance procedures The instructions in this manual have been prepared to aid you in learning the proper proce dures Where information is of particular importance or safety related the words WARNING CAUTION and NOTICE are used Their usage 1s described below SAFETY ALERT SYMBOL is used with DANGER WARN ING or CAUTION which indicates a personal injury type hazard NOTICE is used to highlight especially important information CAUTION used without the safet
15. ld over flow and spill onto the floor and personal injury could result Y PENNY Olof Foodrervice Solutions 3 3 START UP Slot Figure 3 2 303 Y PENNY Model HHC 990 Global Foodservice Solutions 3 3 START UP Continued 5 Press the TEMPERATURE button to set the desired cabinet temperature While the LED is flashing press the UP and DOWN buttons until the desired tempera ture shows in the display 6 Press the HUMIDITY button to set the desired cabinet humidity OFF to 90 While the LED is flashing press the UP and DOWN buttons until the desired temperature shows in the display 7 Allow the unit to preheat for about 1 hour prior to placing product in the cabinet This allows the interior conditions to stabilize 3 4 OPERATION WITH 1 The LEDs above the TEMPERATURE and HUMIDITY PRODUCT buttons go out when the desired temperature and humidity are reached inside the cabinet Place hot product on pan and slide pan onto the racks of the cabinet The minimum holding temperature for potentially hazardous product is 150 F 66 C Use the food probe to accurately display food temperature Also the cabinet product load capacity for the full size units is 375 Ibs 170 kg and 125 Ib 57 kg for the half sized units View the temperature at any time by pressing l INFQ 2 Press the appropriate timer button 1 15 and the time hours minutes starts counting down in display 3 At the e
16. n then back to FAILED ON if the display shows E 17 the humidity sensor should be checked once the humidity sensor is repaired or replaced the controls should return to normal if E 17 persists have PC board replaced NO WATER FLOAT Float switch stuck or e Turn switch to OFF position then back to SWITCH FAILED faulty faulty relay ON if the display shows E 18 check stuck on water pan and clean float switch clean water pan needs cleaned have relay and water heater sensor loose or faulty water checked and replace if necessary tighten heater sensor acorn nuts acorn nuts on water heater cover make on water heater cover sure 2 complete pieces of insulation are loose or water heater under the water heater cover if E 18 insulation missing or persists have PC board replaced damaged NOVICE A humidity error only shuts down the humidity system If a humidity error occurs and you want to use the cabinet without humidity turn the humidity off by following the directions for SP 4 Humidity Setpoint in Special Programming Section of this manual Once the setpoint is off the alarm stops but the error code shows in display Includes E 12A E 12B E 17 and E 18 4 8 804 Y PENNY Model HHC 990 Global Foodservice J 5 2 ERROR CODES AND WARNINGS Continued Display Panel Board Correction 41 SYSTEM DATALOST Memory scrambled Turn switch to OFF p
17. nd of the timing period the control beeps and 0 00 flashes in display A float switch in the water pan senses when the water level is low and the display shows WATER LEVEL LOW Add more water to the water pan 4 Open the doors only as necessary to load and unload product This helps to keep the interior conditions constant and saves energy 3 5 303 Y PENNY Model HHC 990 obal Foodrervice Solutions 3 5 CLEANING Daily PROCEDURES 1 Turn all controls off and disconnect electrical supply BURN RISK To avoid burns allow the unit to cool before cleaning 2 Open doors and remove all trays and racks from unit and take them to a sink to thoroughly clean Figure 3 3 3 Wipe interior and exterior of cabinet with damp cloth soap and water Do not use steel wool other abrasive cleaners or cleaners sanitizers containing chlorine bromine iodine or ammonia chemicals as these will deteriorate the stainless steel and glass material and shorten the life of the unit Do not use a water jet pressure sprayer to clean the unit or component failure could result 4 Wipe the control panel with a damp cloth Do not splash water around controls 5 Reinstall racks and leave a door partially open over night to allow interior cabinet to thoroughly dry 303 3 6 H Y PENNY Model HHC 990 Global Foodservice Solutions 3 5 _ CLEANING Weekly PROCEDURES Continued 1 Remove pans and racks f
18. net is now ready for location and use Place the humidified holding cabinet in an area that allows the doors to be opened without interference of loading and unloading product Also keep the unit level for proper operation No minimum clearances are required for the rear and sides of the cabinet 303 2 2 UNPACKING Continued 2 3 LOCATION Model HHC 990 SHOCK HAZARD To avoid electrical shock the cabinet must be adequately and safely grounded earthed according to local electrical codes and this appliance must be equipped with an exter nal circuit breaker which will disconnect all ungrounded unearthed conductors The main power switch on this appliance does not disconnect all line conductors FOR EQUIPMENT WITH CE MARK ONLY To prevent electric shock hazard this appliance must be bonded to other appliances or touchable metal surfaces in close proximity to this appliance with an equipotential bonding conductor This appliance is pped with an juipotential lug equipotential lug for this purpose Th is marked with the following symbol If the electrical supply to the unit is a cord and plug then the electrical receptacle for the plug must be easily accessible Refer to the table below for the electrical ratings for the HHC 990 series cabinets Watts 2 3 2880 2680 2880 2876 2676 2192 2080 2080 2076 1992 3280 3280 3276 3876 3192 2080 2880 2680 2880 2076 2816 1992 279
19. osition then back to ON if the display shows E 41 the control should be re initialized see Pro gramming Section if E 41 persists have PC board replaced 46 DATA SAVE FAILED Memory scrambled Turn switch to OFF position then back to ON if the display shows E 46 the control should be re initialized see Pro gramming Section if E 46 persists have PC board replaced E 80 VENT STUCK OR e Vent on rear of module Check vent on rear of module for obstruc BAD SWITCH stuck or faulty vent tions or have vent activation switch activation switch replaced PLEASE DE LIME Water pan needs Follow the weekly cleaning procedures ATER PAN cleaned this warning will not shut down the heat or humidity if PLEASE DE LIME WATER PAN persists have PC board replaced WATER LEVEL LOW PLEASE Water pan low on vvaterl Fill water pan in bottom of unit to the or empty maximum water fill mark this warning won t shut down the heat or humidity 303 4 8 Model HHC 990 GLOSSARY HENNY PENNY HOLDING CABINETS a round device located inside the cabinet that measures the inside air temperature and sends that information to the control panel a metal assembly located in the vvater pan in the bottom 01 the unit that helps keep an even humidity level inside the cabinet a preset temperature at which a sensor warns the operator that the water pan has excessive lime deposits the components that control
20. placement of a part EXTENDED FRYPOT WARRANTY Henny Penny will replace any frypot that fails due to manufacturing or workmanship issues for a period of up to seven 7 years from date of manufacture This warranty shall not cover any frypot that fails due to any misuse or abuse such as heating of the frypot without shortening 0 TO 3 YEARS During this time any frypot that fails due to manufacturing or workmanship 15 sues will be replaced at no charge for parts labor or freight Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost 3 TO 7 YEARS During this time any frypot that fails due to manufacturing or workmanship 15 sues will be replaced at no charge for the frypot only Any freight charges and labor costs to install the new frypot as well as the cost of any other parts replaced such as insulation thermal sensors high limits fittings and hardware will be the responsibility of the owner Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased No allowance will be granted for repairs made by anyone else without Henny Penny s written consent If damage occurs during shipping notify the sender at once so that a claim may be filed THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY FOR ANY BREACH OF WARRANTY OR OTHER TERM BUYER AGREES THAT NO OTHER REMEDY INCLUDING CLAIMS FOR ANY INCIDENTAL O
21. r louvers clogged AIR TEMP TOO HOT Faulty relay PC board or air probe CPU TEMP SENSOR Faulty PC board OPEN CPU TEMP SENSOR Faulty PC board SHORTED AIR TEMP SENSOR Faulty air probe FAILED OPEN 303 Model HHC 990 HENNY PENNY 5 2 ERROR CODES AND WARNINGS Continued Display Panel Board Correction E 6B AIR TEMP SENSOR Faulty air temperature Turn switch to OFF position then back to FAILED SHORTED probe ON if the display shows E 6 the temperature probe should be checked once the temperature probe is repaired or replaced the controls should return to normal if E 6 persists have PC board replaced WATER HEATER Faulty water Turn switch to OFF position then back to SENSOR FAILED heater probe ON if the display shows E 12A the OPEN water heater should be checked and repaired or replaced the water heater probe is built into the water heater the controls should return to normal if CE I2A persists have PC board replaced WATER HEATER Faulty water Turn switch to OFF position then back to SENSOR FAILED heater probe ON if the display shows E 12B the CLOSED water heater should be checked and repaired or replaced the water heater probe is built into the water heater the controls should return to normal if E 12B persists have PC board replaced HUMIDITY SENSOR Faulty humidity sensor Turn switch to OFF positio
22. rom cabinet 2 Open drain valve and empty water pan into a shallow pan or floor drain See Figure 3 4 HOT WATER Hot water Do not place your hand under the drain while draining the unit Failure to follow this warning could result in severe burns and injury 3 Remove concentration ring assembly from water pan See Figure 3 5 5 HOT SURFACE Concentration ring could be hot Allovv to cool before removing or burns could result 4 Wash the concentration ring in a dishwasher or sink 5 Liberally spray the water pan with a concentrated deliming agent and let stand for 10 minutes To avoid damage to the unit delime the unit weekly 6 Scrub the pan with a brush and flush with water 7 Return concentration ring assembly to the water pan 8 Reinstall the racks and fill the water pan with water to the maximum water fill line 9 Unit is now ready for use Monthly Remove the 2 screws securing the vented panel on the rear of the module and remove the panel and clean vents Using a cloth or sponge clean the trough once a month Figure 3 4 3 7 303 Model HHC 990 This section explains the following programming functions Timer programming e Clock set Special programming To enter the Program Mode Press and hold for 2 seconds and PROG TMRS PROG shows in display After 5 seconds ENTER CODE shows in display Press _and PUSH TI
23. ued Control Decal Es k HENNY PENNY en prenes HHC 990 SmartHold a _ 0 10 Figure 3 1 3 3 303 Model HHC 990 Before using the humidified holding cabinet thoroughly clean the unit as described in the Cleaning Procedures Section 01 this manual Plug unit into electrical receptacle or turn on wall circuit breaker With the POWER switch turned to OFF the display shows POWER OFF With the POWER Switch off the display may show PURGING This means the humidity has reached 95 inside the unit and the fan runs to help drop the humidity Once the humidity reaches 92 POWER OFF again shows in the display 9 Even though POWER switch is OFF it does not dis connect all electrical supplies to the controls Unplug power cord or turn off wall circuit breaker before servicing any electrical components or electrical shock could result Turn the POWER switch to ON and the display shows PUSH TO PROOF If the unit is to be used as a proofer 80 140 F 27 60 C press the HUMIDITY button within 10 seconds while thedisplay still shows PUSH TO PROOF If not allow unit to heat normally 140 210 F 60 99 C Open door of unit and pour up to 3 gallons of water into bottom water pan minimum 1 gallon up to the slot on the concentration ring See figure 3 2 Do not overfill the water pan or water cou
24. vice should NOT be used to clean a holding cabinet 303 VY PENNY Global Foodservice Solutions air temperature probe concentration ring assembly clean water pan setpoint control panel deliming agent drain valve float switch food probe food probe receptacle humidity sensor humidity setting LED minimum holding temperature module out of water trip point parameters power switch pressure sprayer Model HHC 990 a metal holder that attaches to the outside 01 the control panel to hold the food probe vvhen not in use the clip is an optional accessory the highest recommended number of pounds kilograms of food product that can be safely held in the cabinet a program used for allowing bread to rise the humidity level inside the cabinet a preset temperature or humidity the setpoint is a programmable feature a programming process that resets factory settings a preset temperature up to which the cabinet will heat this setting is programmed at the factory but can be changed in the field an automatic control that opens and closes the vent on the rear of the cabinet to maintain the preset humidity level openings on the cabinet that allow air access on the sides and rear of the module the line marked on the inside of the water pan that shows the maximum water level to prevent overflow onto the floor a part in the water heater that sends a message to the controls when the water pan is lime
25. w See photo at left The food probe is accessed easier if the clip 18 mounted on the side of the unit that the door opens See photo below Mount clip here PENNY 2 6 PROBE CLIP OPTIONAL Probe Clip 303 Model HHC 990 Y PENNY Mobal Foodrervice Solutions INTRODUCTION This section provides explanations of all controls along with operating procedures and daily maintenance Read the Introduction Installation and Operation Sections before operating the unit Function Description Item No 3 1 3 2 OPERATING CONTROLS Fig No A rocker switch that sends electrical current to the operating components when turned on Lights when the control calls for heat and the unit should start heating it goes out once the temperature inside the cabinet reaches the programmed temperature setting Press the TEMPERATURE Button to set the cabinet temperature Shows the cabinet temperature humidity settings and the selec tions in the Program Mode the temperature of the cabinet is shown by pressing the INFO button if the temperature exceeds 300 F 149 C the display reads E 5 TOO HOT Lights when the control calls for humidity it goes out once the humidity inside the cabinet reaches the programmed humidity setting Press the HUMIDITY button to set the relative humidity inside the cabinet and to choose between the Proofing and Holding Modes when the unit is turned on
26. y alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION used with the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury 1 2 303 Model HHC 990 2 1 INTRODUCTION Installation 01 this unit should 06 performed only by a qualified service technician SHOCK HAZARD Do not puncture the skin of the unit with drills or screws or component damage or electrical shock could result 2 2 UNPACKING The Henny Penny humidified holding cabinet has been tested inspected and expertly packed to ensure arrival at its destination in the best possible condition NOGE Note any shipping damage in the presence of the delivery agent and signed prior to his or her departure To remove the Henny Penny cabinet from carton 1 Carefully cut banding straps 2 Lift carton off the unit 3 Lift the unit off the cardboard padding and skid Full size cabinets weigh approximately 300 Ibs 136 kg Care should be taken when lifting unit to prevent personal injury 303 2 1 Model HHC 990 4 Open doors and remove packing from behind racks and the water pan in the bottom of the unit 5 Peel off any protective covering from the exterior of the cabinet 6 The cabi
Download Pdf Manuals
Related Search