Marantz PM7001 Stereo Amplifier User Manual
Contents
1. CD TUNER AUX RECORDER1 RECORDER 2 DVD IN OUT connections ENGLISH Speaker Main amplifier Speaker If you have another main amplifier you can use the PM7001 as the pre amplifier by connecting as shown in the diagram below To input jacks To power outlet SPEAKERS Set to OFF Remove LCH Remove Remove RCH Remove shorting speaker shorting shorting speaker shorting bar bar bar bar Use a bi wiring connection pg 3 for speakers Set the SPEAKERS button 1 and button 2 on the front panel in the ON position HSITSNA NAMES AND FUNCTIONS OF PARTS FRONT PANEL POWER ON OFF button Pressing this button once turns power to the amplifier ON and pressing it again turns power to the amplifier OFF When the button is in the ON position power can be switched ON OFF using the supplied remote controller If the power is switched OFF using the remote controller the amplifier engages in standby mode When in this mode you cannot switch the power ON by pressing the POWER ON OFF button The amplifier remains in standby mode even if this button is pressed To switch the power ON either turn the INPUT SELECTOR knob 3 or press the MAIN POWER ON button 1 on the remote controller 2 STANDBY indicator This indicator is lit red when the amplifier is in standby mode When in sta2. Using this remote controller you can control the PM7001 and Marantz CD players DVD players tuners tape decks etc that have a remote control receptor The operations possible by remote controller may differ with each component therefore see the instruction manual that came with the component See page 13 The RC4001PM remote controller buttons are laid out as shown below AAA marantz MAIN POWER source OFF Power AMP f OO RECORDER AUX DVD TAPE MD o o en o 3 o b O B OOO 9 MODE ODO 4 MODE 2 SCROLL CANCEL TEXT TIME OOOO CLOSE OOC IO SYSTEM REMOTE CONTROLLER HE4001PM Pi Power ON OFF buttons MAIN POWER ON button This button switches the power ON when the PM7001 is in STANDBY mode MAIN POWER OFF button This button switches the PM7001 to STANDBY mode when the power is ON SOURCE POWER button This button switches between power ON and STANDBY modes for Marantz products that have a standby function By pressing this button after one of the buttons in the button group 2 you can switch the power between ON and STANDBY modes for the Marantz product that corresponds to that button By pressing this button after the AMP button 2 you
3. m a ENGLISH www marantz com You can find your nearest authorized distributor or dealer on our website U S A Marantz America Inc 1100 Maplewood Drive Itasca IL 60143 U S A EUROPE Marantz Europe B V P O Box 8744 5605 LS Eindhoven The Netherlands HBR a Weak ERE TZ is a registered trademark Printed in China 01 2006 00M14AJ851250 mzh g
4. In these cases the MUTE indicator in the center of the panel flashes and the volume is automatically reduced Approximately 15 seconds later the protective circuit is released therefore the volume needs readjusting to continue normal use Moreover if the overcurrent continues the amplifier s power shuts OFF and the STANDBY indicator above the POWER ON OFF button flashes e If excessive ultra bass signals are input The protective circuit is also activated if ultra bass signals that exceed the base signal range settings are input In this case the MUTE indicator in the center of the panel flashes and the volume is automatically reduced Approximately 15 seconds later the protective circuit is released therefore the volume needs readjusting to continue normal use If excessive ultra bass signal input continues or if DC voltage is detected due to trouble with the amplifier the power shuts OFF and the STANDBY indicator above the POWER ON OFF button flashes e If the Main amplifier Overheats The protective circuit is activated if the temperature of the main amplifier section rises above a certain level which can happen if the amplifier is continually used with excessive signal flow being input into it The protective circuit is also activated when the set operating temperature is exceeded which can happen if the vents on top of the amplifier are covered or if the amplifier is installed on a cramped audio rack In these cases the MUT
5. jacks BUTTON NAME FUNCTION F P Frequency Direct F P E Preset 10 E MODE T mode Stereo Mono MODE MEMO Memo MEMO SCROLL CANCEL Display Cancel SCROLL CANCEL Counter Reset TEXT MODE EI Preset Scan TEXT MODE HI None TIME MODE A IF Band TIME MODE A Time Display 1 9 Preset 1 Preset 9 1 9 1 9 None 0 0 None Preset Down Back Skip Preset Up None Forward Skip vit Back Skip None Forward Skip Tuning Down Fast Rewind Tuning Up Fast Forward None y11v1 Stop None A v Direction None iT Pause OPEN CLOSE None OPEN CLOSE Eject names AND FUNCTIONS OF PARTS J m For use of Remote controller e Loading batteries Before using the remote controller for the first time load the batteries in the remote controller The batteries provided are used to verify the operations of the remote controller only HSITSNA 1 Remove the battery cover which is found on the back side of the remote controller SS 2 Load the two new size AA batteries inside the battery compartment while taking care to align their polarities correctly with the polarity markings with and with 3 Push the cover on the back side in the direction of the arrow to close 1
6. OR SYSTEM2 4 18 OHMS OHMS SYSTEM 1 AND SYSTEM 2 8 16 For details connecting the speakers see page 5 13 ENGLISH HSITSNA TROUBLESHOOTING m Before considering it as a failure In case of trouble with this component first check the following before calling for service What seems to be a serious malfunction is often due to a simple operation mistake If the trouble is not fixed after making the following checks contact the place of purchase your nearest Marantz dealer our customer service center or our repair service center Power does not turn ON 1 Is the power cable plugged securely into the power outlet 2 Isn t the STANDBY indicator above the POWER ON OFF button lit Either turn the INPUT SELECTOR knob or press the MAIN POWER ON button on the remote controller 3 If the STANDBY indicator is flashing the protective circuit has been activated Switch the PM7001 s POWER ON OFF button to the OFF position wait for more than a minute and then turn the power back ON Nothing is heard from the speakers 1 Aren t the SPEAKER 1 and 2 buttons on the front panel in the OFF position 2 Isn t the MUTE function activated 3 Did you make a mistake selecting the input source using the INPUT SELECTOR knob on the front panel 4 Are you using the component correctly 5 Are connection cables and speaker cables securely connected 6 Is the SEPARATE switch on the rear
7. can switch the PM7001 between power ON and STANDBY modes Input selector buttons This group of buttons is used for selecting the input source Caution In the PM7001 AUX and DVD and RECORDER 2 s TAPE and MD each share the same input jacks The signal codes for controlling these Marantz products using the RC4001PM differ therefore separate buttons have been built into the remote controller VOLUME adjustment buttons MUTE Button This button activates the mute function Pressing this button again releases the MUTE function The MUTE function can also be released by pressing either the VOLUME A or Y buttons 3 VOLUME A Button This button increases the volume level VOLUME v Button This button decreases the volume level Component operating buttons These buttons are for performing basic operations of a Marantz CD player DVD player etc The function of each button changes to match the component selected as the input source using the input selector buttons 2 NAMES AND FUNCTIONS OF PARTS m CD When the CD button 2 is pressed the buttons in group 4 function as indicated in the table below These buttons can only be used when a Marantz CD player is connected to the m DVD When the DVD button 2 is pressed the buttons in group 4 function as indicated in the table below These buttons can only be used when a Marantz DVD player is connected to the ENGLIS
8. panel set correctly 7 The volume may have been muted by the protective circuit activated Try adjusting the volume level again Record player audio is not heard or contains a lot of noise 1 Are the PHONO plugs connected correctly 2 Connect the grounding wire from the record player to the PHONO GND terminal Is the cartridge connected properly to the tone arm 4 Sometimes plugging the record player s power cable into the power outlet with the polarity reversed can reduce noise wm m About the Protective Circuit The PM7001 is equipped with a protective circuit to protect the amplifier circuits and speaker system against damage If the protective circuit is activated the sound is instantly muted In this case either the MUTE indicator in the center of the panel flashes or the STANDBY indicator above the POWER ON OFF button flashes e At Power On For about 8 seconds after the power is turned on the protective circuit is activated muting the sound to give the amplifier circuits time to stabilize Once the amplifier circuits stabilize the protective circuit releases and audio is enabled 14 e In the Event of Overcurrent The protective circuit is activated if current exceeding a certain level is detected which can happen if excessive signal flow is input to the amplifier or if the PM7001 is connected to a speaker system of less than 4Q impedance The protective circuit is also activated if a speaker cable shorts
9. which faithfully amplify signals from the CD player Moreover the high speed current feedback amplifier reproduces a natural sound field space BEFORE MAKING CONNECTIONS WIRING SPEAKER CABLE Be careful not to short circuit in wiring speaker cables e Peel off the corting of speaker cable as shown below Approx 7 16 ins 10 mm Cut the corting of Peel off the Twist cable edge of cable conductors e Wiring with speaker cable Turn clockwise to tighten Insert conductor to loosen of cable Turn counter clockwise Your speaker system must satisfy the below conditions If it does not the PM7001 s protective circuit will active whereby preventing proper playback In some cases the amplifier and speakers may be damaged If using 1 set of speakers total speaker impedance must be 4Q or more e If using 2 sets of speakers total speaker impedance must be 8Q or more Here following is explained BI WIRING connection that im prove sound quality The speakers in this explanation have low and mid high input jacks that support a BI WIRING con nection To determine whether or not your speakers support a BI WIRING connection check in the instruction manual that came with your speakers or contact the manufacturer ENGLISH BI WIRING CONNECTION A bi wiring connection separately connects the low and mid high jacks of the speaker to the amplifier using separate spea
10. 0 Operatable range of Remote controller Operate the remote controller RC4001PM within a distance of approx 5m from the infrared receptor window on the front of the PM7001 Approx 16 4 ft 5m Remote controller RC4001PM e Caution e Do not allow direct sunlight an inverter fluorescent light or other strong source of light to shine onto the player s infrared receptor window Otherwise the operation of the remote controller may be disabled Bear in mind that operating the remote controller may cause other devices operated by infrared rays to be operated by mistake e The remote controller cannot be operated if the space between the controller and the player s infrared reseptor window is obstructed e Do not place any objects on top of the remote controller Doing so may cause one or more buttons to be held down which will cause the batteries to run down BASIC OPERATION PLAYBACK To explain how to play back input sources representative examples are given with an CD player and analog record player Before starting either procedure check the component is correctly connected to the PM7001 m Disc Playback on an CD Player Press the power ON OFF button of the CD player to activate power to it 2 Press the POWER ON OFF button to activate power to it Approximately 8 seconds after power has been activated the muting turns OFF and audio output is enabled 3 Select the CD f
11. E indicator in the center of the panel flashes and the volume is automatically reduced Approximately 15 seconds later the protective circuit is released therefore the volume needs readjusting to continue normal use If the temperature does not sufficiently lower within a certain amount of time after the protective circuit activation the power shuts OFF and the STANDBY indicator above the POWER ON OFF button flashes e In the Event of Amplifier Trouble The protective circuit is activated and the power is automatically shut OFF if an abnormality is detected in the power circuit The same happens if the main fuse inside the amplifier blows In these cases the STANDBY indicator above the POWER ON OFF button flashes OTHERS The section describes the care and maintenance tasks that must be performed to optimize the operation of your Marantz component m Cleaning of equipment external surfaces The exterior finish of your unit will last indefinitely with proper care and cleaning Never use scouring pads steel wool scourging powders or harsh chemical agents e g lye solution alcohol thinner benzine insecticide or other volatile substances as these wil mar the finish of the equipment Likewise never use cloths containing chemical substances If the equipment get dirty wipe the external surfaces with a soft lint free cloth If the equipment becomes heavily soiled e dilute some washing up liquid in water in a ratio of
12. H CD input jacks BUTTON NAME FUNCTION AUX DVD input jacks BUTTON NAME FUNCTION F P None F P Disc Skip E Disc Select El Disc Skip MODE Auto Music Scan AMS MODE None MEMO Program MEMO None SCROLL Scroll Recall Program SCROLL None CANCEL Cancel CANCEL None TEXT MODE EI Text TEXT MODE i Audio TIME MODE pa Time 1 9 TIME MODE A OSD 1 9 ae co 0 0 Previous Track Previous Chapter Next Track Next Chapter Play Play Previous Track Previous Chapter Next Track Next Chapter Fast Reverse Scan Fast Forward Scan Stop BAT a yt fo Stop None Pause A v None u Pause OPEN CLOSE m TUNER Open Close OPEN CLOSE Open Close m TAPE When the TUNER button 2 is pressed the buttons in group function as indicated in the table below These buttons can only be used when a Marantz tuner is connected to the TUNER When the RECORDER 2 TAPE button 2 is pressed the buttons in group 4 function as indicated in the table below These buttons can only be used when a Marantz tape deck is A input jacks BUTTON NAME FUNCTION connected to the RECORDER 2 TAPE
13. ONO MM coooccccocncocncconnononnonnnonnnnonnncnnnnn 2 5mV 47kQ CD LINE TUNER AUX DVD RECORDER ie te meets be 200mV 20kQ MAIN IN er 1 6V 20kQ Output voltage Output impedance PRE OUT so ira dsd 1 6 V 560Q Maximum allowable PHONO input level 1kHz A e 130mV RIAA deviation 20Hz 20KHZ oooooococcincoinciccccnco 0 5dB S N IHF A 1W 8Q load PHONO MM coooocccocccnonnconncnnncnnnonnncns 85dB 5mV input CD LINE TUNER AUX DVD RECORDER O O AEE E 88dB 500mV input MAIN IN eeaeee onr adrian iii 107dB Tone control A A letsuerasusatiansl 10dB Treble 20KHZ sviesiai naonao ennah 10dB Power requirement scceeeseeeeseeeeeseeereees AC 120V 60Hz Power consumption WEG SOO arta i tildado asii 250W 40 100W X 2 OUTPUT coooocccnocccccoonccononnconancnnnancnnnnnos 470W Accessories Remote controlen si sctec cess ccete caeesescueenedanacetes ceases stchentee 1 AA battere Sesinia eer eales aiaia 2 Detachable AC power cable ccceeceeeeteeteeeeeeeneees 1 Maximum outer dimensions Amplifier WHOA cccisiec ceed ltentetes ice sansa 17 5 16 ins 440 mm A sn 5 ins 126 5 mm Depth inicia erst iels ave aveniedh 14 3 8 ins 364 mm Weight Amplifier cceceeseeeeeeeeeeeeeeees 23 1 lbs 10 5 kg Specifications subject to change without prior notice 5 16 ins 23 0 mm 1 gt 14 3 8 ins 364 mm 440 0 mm 5 ins 126 5 mm gt 11 16 ins 16 5 mm
14. ccccoconocicnocononcnnnonanccnrncnan cono coran coronan nn nano ncnnn 15 BEFORE USE This section must be read before any connection is made to the mains supply m EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area PM7001 can be powered by 120V AC only m COPYRIGHT Recording and playback of any material may require consent For further information refer to the following Copyright Act 1956 Dramatic and Musical Performers Act 1958 Performers Protection Acts 1963 and 1972 Any subsequent statutory enactments and orders m Do Not Locate in the Following Places To ensure long lasting use do not locate the PM7001 where Exposed to direct sunlight e Near to sources of heat such as heaters e Highly humid or poorly ventilated e Dusty e Subjected to mechanical vibrations On wobbly inclined or otherwise unstable surfaces e Radiated heat is blocked such as in cramped audio racks To ensure proper heat radiation ensure the below clearance from walls and other equipment Left 7 7 8 ins Above 7 7 8 ins 0 2 m or more 0 2 m or more Right 7 7 8 ins 0 2 m of more Rear 7 7 8 ins 0 2 m or more m Keep Objects Off Keep objects off the PM7001 Blocking the vent can result in accident and damage m Do Not Touch Hot Spots During and Immediately After Use During a
15. ch of the CD player and CD R to activate power to both components 2 Press the POWER ON OFF switch to activate power to it Approximately 8 seconds after power has been activated the muting turns OFF and audio output is enabled 3 Select the CD with the REC SELECTOR knob 2 If you want to listen to the recording source through the speakers set the INPUT SELECTOR knob 3 to the CD position 4 Load a playback disc into the CD player and a recording disc into the CD R 5 Start playback on the CD player Then start recording on the CD R About the REC SELECTOR The REC SELECTOR knob 2 can be operated independently irrespective of the input source selected using the INPUT SELECTOR knob OFF Cannot record because no signal is output to the RECORDER 1 2 jacks PHONO CD TUNER AUX DVD Selects the program source for recording COPY RECORDER 1 2 Select this to copy the RECORDER 1 signal onto RECORDER 2 COPY RECORDER 2 1 Select this to copy the RECORDER 2 signal onto RECORDER 1 11 ENGLISH HOW TO USE AND SET FEATURES MAIN IN JACKS HSITSNA You can separate the pre amplifier section and main amplifier section by using the SEPARATE switch settings on the PM7001 If you have another pre amplifier you can use the PM7001 as the main amplifier by connecting as shown in the diagram below Pre amplifier A To PRE OUT Jacks To power outlet Set
16. ep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacture s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over LA rs Bb Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is dama
17. ged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Additional Safety Information This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus When the switch is in the OFF position the apparatus isn t completely switched off from the MAINS HSITSNA CONTENTS BEFORE USE cuore ET 1 FEATURES unica de AICA 2 BEFORE MAKING CONNECTIONS dcciccccccccconcconcnnonononcononcnnn conca ran ee aaaea nn rre 3 WIRING SPEAKER CABLE suis ToS oivece ig cose BSE lead ante GA esas 3 BI WIRING CONNECTION ciaci n citant tal A e 3 CONNECTIONS Sonora cs 4 NAMES AND FUNCTIONS OF PARTS encino 6 FRONT PANEL sico eiii litio onde deena eae 6 PEAR PANEL coito iia 7 RC4001PM REMOTE CONT ROLLER ci occiso do dd as 8 BASIC OPERATION scott tadas EAS ea cirio nasi eee recente 11 PLAYBACK iuris id den 11 A nn aA EEEE aa RE Ta EON Naaa EVE aSa Oaai 11 HOW TO USE AND SET FEATURES coincidido ios 12 MAININ JACK SS iii id is 12 REMOTE CONTROL JACKS tunas ista ll osas ers Ea 13 TROUBLESHOOTING curtido 14 OTHERS Lamar ds 15 SPECIFICATIONS amp DIMENSIONAL DRAWINGS ooocoo
18. input buffer amplifier nearby the CD input jack This buffer amplifier faithfully transmits the CD input jack signal by preventing interference from between the left and right channels and from the effects of other circuits A discrete configuration high speed buffer amplifier which is built on the HDAM SA technology is incorporated into the buffer amplifier circuit e CD Direct Selector The output of CD direct buffer amplifier has a specialized relay switch which directly transmits the input signal by the shortest path to the pre amplifier e Improved Momentary Current Supply Capability It is known that sound quality differs between amplifiers that use the same spec and Marantz believes that this is caused by differences in speaker drive capability The PM7001 main amplifier has the capability to momentarily pass 25 amperes or more of current providing high powered drive to the speakers e Short Power Line Layout In order to improve the momentary current supply capability a new layout which places priority on making the large current line connections as short as possible was adopted In this layout the power supply circuit main amplifier output stage and heatsink are unified and the large current line is arranged to be as short as possible while still achieving symmetry on the left and right sides e Current Feedback Amplifier Both pre amplifier and main amplifier incorporate a high speed current feedback amplifier circuit
19. ke copies We recommend the knob be set to the OFF position when not recording to obtain optimal sound quality See page 11 names AND FUNCTIONS OF PARTS 3 Infrared Receptor Window This is the receptor of control signals sent from the RC4001PM remote controller Point the remote controller towards this window to properly transmit signals REAR PANEL SvSTEM2 O PHONO Input jacks These jacks are for connecting to an analog record player MM cartridges can be used PHONO GND terminal Connect the grounding wire from an analog record player PRE OUT jacks These jacks are for connecting to the input jacks of an other main amplifier or active subwoofer MAIN IN jacks These jacks are for connecting to the output terminals of another pre amplifier when using the PM7001 as the main amplifier In this case set the SEPARATE switch to the ON position SPEAKERS SYSTEM 1 2 output terminals You can connect 2 speaker systems SPEAKERS 1 and SPEAKERS 2 Speaker output can be turned ON OFF from the SPEAKERS 1 and 2 buttons on the front panel AC IN socket Connect the supplied AC power cable to this socket and a power outlet REMOTE CONTROL jacks These jacks are for connecting to other Marantz components such as a CD player or DVD player that has a remote control connector D BUS jack You can use the remote controller supplied with the PM7001 to control the system F
20. ker cables Because separate cables are used for low and mid high sounds the kick back current in the low speaker causes little interference with the mid high speaker The PM7001 and speakers of Connection Example 1 pg 5 use a bi wiring connection therefore also refer to that page for help Bi wiring Speaker system connection 7 HI epale ane iier EN aie CONNECTIONS HSITSNA Record Player Connection Example Basic Connection for Stereo Playback Refer also to the instruction manuals of components to connect equipment correctly To LINE OUT jacks E gt o ooo O oo oojoo oooO e A AK lt T gt lt CD player To LINE OUT jacks o bees sos 0 Tuner To LINE OUT jacks A a O o ooo DVD Player To LINE OUT jacks Lo yy Oo oo Oooo CD R etc Mn U E IN jacks E OUT jacks N N MD or Tape deck etc U To LINE IN jacks
21. maranitz Model PM7001 User Guide rt Integrated Amplifier CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shockto persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOC ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON DANTE DE LA PRISE ET POUSSER JUSQU AU FOND IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards There are however some installation and operation precautions which you should be particularly aware of f 10 11 12 13 14 oN o oF PF SN Read these instructions Ke
22. me The volume can also be adjusted using the remote controller If the amplifier s protective circuit activates the VOLUME knob automatically turns for approx 15 seconds and the volume decreases SOURCE DIRECT button When this button is pressed in the audio signal is transmitted bypassing the balance and tone control circuits allowing you to enjoy a higher level of sound quality SPEAKERS 1 2 buttons These buttons turn the speaker output to the speakers connected to the SPEAKERS SYSTEM 1 and 2 terminals on the rear panel ON and OFF When listening with headphones turn the speaker output OFF BALANCE knob This knob is used to adjust the sound level from one of either the L left or R right channels If the BALANCE knob 0 is turned all the way round to one side sound is not output from the opposite side Please note that this knob does not function when the SOURCE DIRECT button 8 is in the ON position 4 Tone Control knobs BASS TREBLE These knobs are used to adjust the BASS and TREBLE sound level Turning the knobs clockwise increases the sound level and turning them counterclockwise decreases the sound level Please note that these knobs do not function when the SOURCE DIRECT button 8 is in the ON position 2 REC SELECTOR knob This knob switches the input sources for recording Moreover you can connect a tape deck CD R player and other such device to the RECORDER 1 and 2 terminals O to ma
23. nd immediately after use the PM7001 is hot in areas other than the controls and rear panel connection jacks Do not touch hot spots and especially the top panel Contact with hot areas can cause burns m Battery Handling Improper use of dry cell batteries can result in electrolyte leaks rupture and corrosion Read the following precautions before use e If not planning to use the remote controller for an extended period of 1 month or more remove the batteries e Do not mix old batteries with new batteries e Load batteries in the proper direction indicated on the re mote controller Do not mix batteries of differing type Even batteries of the same shape and size can have differing voltages e If batteries leak wipe the case clean of any adhering elec trolyte and replace the old batteries with new batteries m Accessories Check Before use check the below accessories were included in the package e AC power cable The power cable included in the package can be used with the PM7001 only It cannot be used with other equipment e RC4001PM remote controller e AA size batteries x 2 e Registration Card e User Guide This manual ENGLISH HSITSNA FEATURES Marantz wreonateo AMPLIFIER Pm7001 The PM7001 is an integrated amplifier developed on the design concepts of Marantz s PM 11S1 high end model amplifier e CD Direct Buffer Amplifier The PM7001 incorporates a specialized
24. ndby mode you can switch the power ON by using the MAIN POWER ON button 1 on the remote controller If the amplifiers protective circuit activates this indicator flashes and the amplifiers power automatically shuts off 3 INPUT SELECTOR knob This knob selects the input source for playback The selected input source is displayed on the function indicator The amplifier memorize the selected input source when the power is turned OFF and then re selects the same input source when the power is turned ON again 4 MUTE indicator When the MUTE button 3 on the remote controller is pressed the MUTE function is activated and the volume is lowered Pressing the MUTE button 3 again releases the MUTE function Moreover the MUTE function can also be released by pressing the VOLUME A v button 3 on the remote controller If the amplifier s protective circuit activates this indicator flashes for approx 15 seconds and the MUTE function activates While this indicator is flashing the VOLUME knob 2 automatically turns and the volume decreases 5 Function indicator This indicator displays the input source currently selected by the INPUT SELECTOR knob 6 6 Power indicator This indicator is lit a blue color while power to the PM7001 is ON 6 7 VOLUME knob Turning this knob clockwise increases the volume while turning it counterclockwise decreases the volu
25. one part detergent to six parts water dip a soft lint free in the solution and wring the it is damp e wipe the equipment with the damp cloth dry the equipment by wiping it with a dry cloth E Repairs Only the most competent and qualified service technicians should be allowed to service the factory trained warranty station personnel have the knowledge and special facilities needed for repair and calibration of this precision equipment After the warranty period has expired repairs will be performed for a charge if the equipment can be returned to normal operation In the event of difficulty refer to your dealer or write directly to the nearest location to you that is listed on the Marantz Authorized Service Station list If writing please include the model and serial number of the equipment together with a full description of what you think is abnormal about the equipment s behaviour SPECIFICATIONS amp DIMENSIONAL DRAWINGS Power output 20 Hz 20 kHz simultaneous drive of both channels e eel deco ce 70W x 2 8Q load e sesh 100W x 2 40 load Total harmonic distortion 20Hz 20kHz simultaneous drive of both channels 8Q load ooooooococcconicocccccncoccoccccccnnnane 0 02 Output band width 8Q load 0 05 5Hz 60kHz Frequency response CD 1W 8Q load 5Hz 100kHz 3dB Dumping factor 8 load 20Hz 20KHZ oooooicciccccncco o 100 Input sensitivity Input impedance PH
26. or more details see page 13 PHONES jack This jack is for connecting headphones with a standard stereo plug To listen with headphones turn the speaker output OFF by setting the SPEAKERS 1 and 2 buttons in the OFF position SERIAL No o SEPARATE switch This switch is used for selecting the pre amplifier and main amplifier connection modes OFF Select this position when the amplifier is used as a normal integrated amplifier Standard factory set ting ON The pre amplifier and main amplifier are separated The PM7001 can be used as a main amplifier when input is connected to the MAIN IN jacks RECORDER 1 RECORDER 2 output jacks These jacks are for connecting to the recording input jacks of a CD R recorder MD deck tape deck etc Output sig nals can be selected using the REC SELECTOR knob 2 on the front panel RECORDER 1 RECORDER 2 input jacks These jacks are for connecting to the output jacks of a CD R player MD deck tape deck etc AUX DVD input jacks These jacks are for connecting to the output jacks of a DVD player or other LINE component TUNER input jacks These jacks are for connecting to the output jacks of a tuner or other LINE component CD input jacks These jacks are for connecting to the output jacks of a CD player or similar component ENGLISH HSITSNA names AND FUNCTIONS OF PARTS RC4001PM REMOTE CONTROLLER
27. rom the INPUT SELECTOR knob 6 4 To use the speakers connected to the SPEAKERS SYSTEM terminals press the SPEAKERS button 1 and 2 5 Load a disc into the CD player and press the play button to start playback 6 Adjust the volume level from the VOLUME knob 7 Adjust bass treble as desired from the BASS and TREBLE knobs 1 Be sure to first set the SOURCE DIRECT button in the OFF position m Disc Playback on an Analog Record Player 1 Press the POWER ON OFF switch to activate power to it Approximately 8 seconds after power has been activated the muting turns OFF and audio output is enabled 2 Select PHONO as the input source from the INPUT SELECTOR knob To prevent unexpected accidents it is recommended to set the volume level to MIN by turning the VOLUME knob until muting the volume level 3 MM type cartridges can be connected Use a step up transformer when using an MC cartridge 4 To use the speakers connected to the SPEAKERS SYSTEM terminals press the SPEAKERS button 1 and 2 Set a record on the analog record player and play it Adjust the volume level from the VOLUME knob 2 Adjust bass treble as desired from the BASS and TREBLE knobs Be sure to first set the SOURCE DIRECT button in the OFF position NON RECORDING This example explains how to record from an input source such as an CD player to a recording device such as a CD R 1 Press the power ON OFF swit
28. the SPEAKERS 1 and 2 button on the front panel to the ON position SPEAKERS SYSTEMIO L Ol 68 ACIN RECORDER 2 IN OUT QO de Set to ON Remove L CH Remove Remove R CH Remove shorting shorting speaker shorting shorting speaker bar bar bar bar Use a bi wiring connection pg 3 for speakers 12 How TO USE AND SET FEATURES REMOTE CONTROL JACKS The REMOTE CONTROL jacks are for connecting components that are capable of remote control D BUS jacks such as a Marantz CD Player or DVD Player This enables these other components to be operated with the remote controller included with the PM7001 The PM7001 comes with an RC4001PM system remote controller that can operate the basic features of Marantz CD Players and DVD Players Here a brief explanation of how to control the PM7001 and CD5001 using this remote controller is provided As shown in the illustration below connect the REMOTE CONTROL IN jack of the CD5001 to the REMOTE CONTROL OUT jack of the PM7001 and set the CD5001 switch to EXTERNAL Both the PM7001 and CD5001 can be operated by pointing the RC4001PM remote controller pg 8 9 10 at the receptor of the PM7001 Set to EXTERNAL CD5001 DIGITAL OUT REMOTE CONTROL COAX OPT s fa PM7001 SPEAKERS O R SYSTEM1O STEM 1
Download Pdf Manuals
Related Search