Marantz LN9101M Network Card User Manual
Contents
1. The following dimensions can assist in determining the best location for the combi nation of the Marantz VP 11 and the LN9101M Ana morphic Lens System 21 15 16 55 7cm x Installation Overview The LN9101M Anamorphic Lens System is designed to mount together with the Marantz VP 11 onto the ceiling of a typical room Before choosing the location on the ceiling it is important to first read the Installa tion section of the VP 11 User Guide Some of the brackets from the Marantz MT20 op tional ceiling mounting bracket will be used to mount the combination of the projector and LN9101M to the ceiling In some installations the EXT10 bracket will also be used optional extension pole kit This installation guide includes the assembly instuctions from the MT20 and EXT10 Installation Guides for easier installation The LN9101M MT20 EXT10 were designed and manufactured to meet Strict quality and safety standards There are however some installation and operation precautions which you should be particularly aware of 1 Read instructions All the safety and operating instructions should be read before the products are used 2 Retain instructions The safety and operating in structions should be retained for future reference 3 Heed warnings All warnings on the products and in the instructions should be adhered to 4 Follow instructions All installation instructions should be followed 52. CARRY or RE ORIENT the equipment using the Lens A Do not remove the cover from the equip ment B Do not remove lens covers until instructed to do so C Do not insert anything into the equipment through the ventilation holes D Do not handle the mains lead with wet hands E No naked flame sources such as lighted candles should be placed on the equipment F Do not look into the lens when the projector is turned on It could damage your eyesight G When disposing of used batteries please comply with governmental regulations or environmental public instructions rules that apply in your country or area Technical Assistance If at any time you have questions about your Marantz product contact your Marantz Dealer who is familiar with your Marantz equipment and any other brands that may be part of your system If you or your Dealer wish additional help concerning a suspected problem you can receive technical assistance for all Marantz products at Marantz America Inc 100 Corporate Drive Mahwah N J 07430 2041 Tech amp Operational Support hours 9 00 AM to 5 00 PM ET M F Tel 800 654 6633 Toll Free Tel 201 762 6666 Fax 201 762 6687 Parts Customer Service If it is determined that your Marantz product is in need of repair you can return it to your Dealer You can also return it to the Marantz Service Department For assistance on factory repair return procedure contact the Marantz at Marantz
3. Height is 9 13 16 inches 24 9cm Depth is 21 15 16 inches 55 7cm Weight 28 pounds 12 7 kg net 41 pounds 18 6 kg in shipping carton marantz Limited Warranty Marantz America Inc Marantz warrants the following Marantz Products for the periods indicated 1 The following Marantz Audio Video components have a 3 year warranty for both Parts amp Labor from the original purchase date Amplifiers Pre Amplifiers Pre Amplifier Processor Tuners Integrated Amplifiers Tuners Receivers DVD Players CD Recorders CD Players Audio Cassette Decks Learning Remote Control Devices Universal Dock amp DLP Front Projectors 2 Plasma Display Devices have a 3 year warranty for labor 2 years on parts and 1 year on the Panel from the original purchase date 3 Anamorphic Lens System have a 2 year warranty for parts and labor from the original purchase date 4 DLP lamps have a 90 day warranty for parts and labor from the original purchase date What is covered and what is not covered Except as specified below this warranty covers parts and labor to correct all defects in materials and workmanship The following are not covered by the warranty 1 Damage deterioration malfunction or failure to meet performance specifications resulting from a Accident acts of nature misuse abuse neglect or unauthorized product modification b Improper installation removal or maintenance or failure to follow instr
4. Use only the parts provided with the mount along with any parts commercially available that are specified in these instructions 6 Do not modify the mount or the parts provided with the MT20 EXT10 LN9101M 7 Do not use damaged parts If any parts become damaged contact your Marantz Dealer or Marantz 8 All bolts and screws must be tightened securely when instructed to do so 9 After the projector mounting plate is attached to the projector make sure not to block any additional ventilation openings 10 Special techniques and experience are required when installing the projector with the MT20 EXT10 LN9101M Contact your Marantz Dealer to install the projector for you 11 Once the projector is installed periodic safety checks of the rigidity of the MT20 Mounting Brack ets EXT10 Extension Pole LN9101M Anamorphic Lens System and the VP 11 to the ceiling along with secure fastening of all hardware should be conducted on a regular basis After reading the Installation Section of the VP 11 User Guide and it has been determined the EXT10 Extension Pole will be needed to meet the require ments of location and ventilation for the Projector assemble the EXT10 by performing the steps below If the EXT10 will not be needed proceed to the MT20 Assembly on page 7 Note The EXT10 hardware fasteners and parts list are located in a separate shipping carton from the projector 1 The EXT10 is adjustable from 43 3 4 inche
5. America Inc 100 Corporate Drive Mahwah N J 07430 2041 General Office hours 8 30 AM to 5 30 PM ET M F Tel 201 762 6500 Fax 201 762 6670 Copyright 2007 by Marantz America Inc LEICK ML OTo a Ja ts Safety InStructions 2 Thank You and Please Take a Moment 2 Technical Assistance and Customer Service 2 Table of COMICS sec aiccsieiids siccscmren nav xttenenammemmevineiomneareubewurins 3 Important Connector and Cable Information 4 DIMENSIONS viciiecetoircawvewsuieieionacadtuwalwerdunvevssvensenenernwecaa 5 Installation Overview 5 INSCalIO NO Riina 5 9 AIGNIMNENE sine ee ae ee 9 SPECIFICA vini a 10 Warranty RR E E O 11 CAUTION The lenses contained in this product are extremely delicate precision op tics and may be scratched or other wise damaged by physical contact with external objects of any kind It is therefore essential to avoid any such contact or any other mistreatment of the lenses Scratches or other exter nally caused damage to lenses that are deemed to have arisen through neglect or misuse are excluded from protection under the Marantz Limited Warranty 1 The LN9101M Power Supply Adapter should not be connected to the LN9101M Motorized Sled or to the AC Power Wall Outlet until the physical mount ing of the Marantz VP 11 LN9101M Anamorphic Lens System and MT20 EXT10 Mounting Brackets is completed 2 For addi
6. mechanism is com letely dry as it relies upon clean and dry rails to operate smoothly 7 The assembly and adjustemnt of LN9101M EXT10 MT20 will require a Phillips head screw driver ad justable wrench 5 32 and 3 16 allen tools 8 When the symbol illustrated here is located on the product or on the packaging it indicates the product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated col lection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please con tact your local city office your household waste disposal service or the Marantz Dealer where you purchased the product Connector and Cable Information Trigger Connectors The LN9101M Trigger In Out Jacks Receive Send a 12VDC Signal to Activate Deactivate the Anamorphic Lens A 1 8 inch 3 5mm stereo mini phone plug is used for connections 12V DC Trigger si N C Control Ground IR Connectors The LN9101M IR In Port uses a 2 5mm quad mini phone plug and allows connec tion of other brand IR Receivers IR to the LN9101M
7. on the Lens align ment collar and rotate the Lens to straighten out the pattern Then tighten the four locking screws Refer to figure 8 on page 6 Notes Inside the Lens close to the front are two vertical visible black masks When the edge of those masks are parallel with the Lens Holder Post the crosshatch should no longer be tilted Do not look directly into the Lens look off from the side at an angle 5 Rotate the front part of the LN9101M Lens for the best focus 6 Using the appropriate tools loosen the three screws on the Lens Holder Locking Ring while at the same time supporting the Lens on the bottom Refer to figure 29 7 Adjust the height of the LN9101M Lens so its vertical center coin cides with the center of the projector lens and the crosshatch pattern is centered vertically on the screen Tighten the center screw on the Locking Ring and then rotate the LN9101M Lens left to right to center the crosshatch pattern horizontally on the screen Then tighten the two screws previously loosened on the Locking Ring 8 The final adjustment is for straighten out the lines of the crosshatch test patern Loosen the tilt ad Locking Ring Screws Adjustment Screw Figure 29 10 justment screw located near the Lens Holder The front of the LN9101M Lens can be pivoted up or down to straighten out the lines in the test pattern Then tighten the screw to retain the position Note If the screen used is not a c
8. 2 You must pay any shipping charged if it is necessary to ship the product for service However if the necessary repairs are covered under warranty we will pay the return shipping charges to any destination within the United States its possessions or territories 3 Whenever warranty service 1s required you must present the original dated sales receipt or other proof of date of purchase Limitation of implied warranties All implied warranties including warranties of merchantability and fitness for a particular purchase are limited in duration to the length of this warranty Exclusion of damages Marantz liability for any defective product is limited to repair or replacement of the product at Marantz s option Marantz shall not be liable for damage to other products caused by any defects in Marantz products damages based upon inconvenience or loss of use of the product or any other damages whether incidental consequential or otherwise How state law relates to the warranty Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state www marantz com You can find your nearest authorized distributor or dealer on our website U S A Marantz Ameri
9. N9101M shipping carton and orient it as z shown Refer to figure 4A and 4B Note Plate 4 supplied with the MT 20 Ceiling Mount Bracket Kit will not be used Plate 4 Figure 4A Top Adjustment Plate Figure 4B i mr ii SN Adjustment Sled Plate 4 and the Top Adjustment Plate as illustrated in figure 4C Secure it using six 1 4 28x1 2 machine screws and tighten them with the supplied Hex Figure 4C Wrench Refer to figures 5 and 6 1 4 20 tapped hole Screws oe Sled 3 Locate the Lens Holder Assembly from the ship ping carton and orient it as shown in figure 7 Us ing the appropriate tool loosen the two hex head screws located either side of center on the Lock ing Ring Remove the hex head screws lift up on the Lens holder and Locking Ring removing them from the Post Refer to figure 8 LN9101M Sled Mounting screw locations Mounting screw locations a Figure 5 Plate 4 and LN9101M Sled Sled Mounting Plate Figure 6 Lens Holder Assembly Figure 7 Figure 8 Notes Set aside the Lens Lens Holder and Locking Ring as they will be used after the VP 11 Pro jector EXT10 MT20 have been installed and initial setup adjustment have been made The actual Lens Holder Assembly is black in color The above illustrations are shown for purposes of clarity 4 Place the Lens Holder Base onto the LN9101M Sled Mounting Plate with the Lens Holder Post oriented to th
10. ca Inc 100 Corporate Drive Mahwah NJ 07430 U S A im A I ER DI ZZ isa registered trademark Printed in U S A Part No 04104000 06 2007
11. e right Secure the Lens Holder Base with the Mounting screw four supplied locations M6x30mm ma N chine screws Refer to fig N Mounting screw ures 6 and 9 location is Set aside the behind post just assembled Figure 9 LN9101M Plate 4 for later use and proceed to the MT20 Assembly MT20 Assembly Assemble the MT20 by performing the steps below 3 Install the combined refer to figure 10 Plates 1 and 2 or EXT10 Plate 1 with the EXT10 securely to the Building Plate 1 Structure following all of the Local Building Con struction Codes Use suitable hardware in ad equate quantity and size aa depending on the installa tion requirements Q 3 Caution The Projector net Plate 4 LN9101M together with the mounting brackets weighs 80 pounds 36 29 kg 4 Attach the Horizontal Tilting Plate 3 to the previ ously combined plates already installed on ceiling using the 1 4 20 inch screws provided Refer to MT20 and LN9101M Mounting Plates Plate 1 gua Figures 15 and 16 Install two 1 4 20inch screws Notes The MT20 hardware fasteners mounting tem with rubber spacers and metal washers part way plate and parts list are located in a separate into the welded metal studs indicated 1 The shipping carton from the projector Plate 4 newly combined Plate 3 provides 10 degrees of supplied with the LN9101M will be used i
12. erform the nec essary procedures Switch On the projector and activate the built in crosshatch test pattern 2 Using the supplied LN9101M Remote Control press the ON Push button while aiming the Re mote Control at the Sensor The Sensor and the Power On indicating LED are located on the Front Side of the LN9101M opposite side of the connec tion area above the Marantz Logo Note When power is first applied the LN9101M Sled may perform an initialization of the Lens position 9 LN9101M Lens Alignment con t 3 Press the LENS IN Push button on the Remote Control and the Lens will travel to a position in front of the projector Lens Verify the horizon tal center of the LN9101M Lens coincides with the horizontal center of the projector Lens If the LN9101M Lens doesn t line up loosen the screws on the LN9101M Sled and slide the Top Adjust ment Plate slightly to the left or right relative to Plate 4 to center the Lens Tighten the screws Refer to figures 4A 4B 4C and 5 on page 6 Notes The projected test pattern will probably have some forms of geometric distortions as a result of misalignment of the Anamorphic Lens to the projector If a chattering noise is heard during sled movement loosen all eight screws on the sled mounting plate recycle the lens positions several times and then tighten the screws Refer to figures 6 and 9 on page 6 4 If the Test Pattern appears tilted on the screen loosen the four locking screws
13. lign the three 6mm mounting holes on the projector with the mounting holes on Plate 4 and the LN9101M Sled Secure the bracket to the projector using the three 6mm screws Refer to Plate 3 Figure 17 Projector Side Figure 19 Caution The Projector together with the mount ing brackets weighs 80 pounds 36 29 kg It requires two or more persons to safely complete assembly Lift and slide the projector onto the 1 4 20 inch screws previously installed in the metal studs of the plate on the ceiling see arrow in Figure 19 Tighten the 1 4 20 inch screws on both sides of the mount and install four 1 4 20 inch screws and washers into the side of the projector Mounting Plate 4 Refer to figure 20 or figure 21 when the EXT10 is used 6mm screws 1 4 20 tapped hole 6mm screw Ceiling Note For added horizontal stability 1 4 20 eye bolts may be screwed into either side of plate 4 with guide wires attached to the eye bolts Refer to figures 20 and 21 For safety the MT 20 EXT10 is designed to support the weight of the LN9101M and VP 11 Projector without assis tance from the eye bolts with guide wire 7 Before the LN9101M Lens can be installed and adjusted it is important to first complete the Instal lation and Initial Settings of the VP 11 Projector Refer to the User Guide of the VP 11 Projector and perform the necessary procedures When the Installation and Initial Settings of the projector is complete pr
14. maraniz Model LN9101M Installation Guide Anamorphic Lens System The lightning flash with arrowhead within an equilateral triangle is intended to alert the user to the presence of uninsulated danger ous voltage within the product s A enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons Ra SE a a 10 WARNING TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s in structions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polar ized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs co
15. nstead of the MT20 Plate 4 1 Insert Base Plate ar connectors 1 into Plate 3 the lateral position ing slots 3 from the underside of Plate 1 The lateral position ing slots will give horizontal tilt After positioning the plate loosely tighten the screws Indicates Forward 4 lt Positioning of Mount you 2 1 4 inches of Base STREET Bla lateral adjustment for Figure 11 projector alignment Refer to figure 11 Bini 1 Holes for 1 4 20 inch screws with rubber washer and steel washer 2 Holes for 1 4 20 inch screws 3 Holes for 1 4 20 inch screws 2 Base plate connector holes 3 provide 15 degrees of horizontal rotation adjustment Figure 15 Attach horizontal adjustment Plate 2 to Plate 3 the projector mount Figure 12 ceiling Plate 1 using the four 4 5 16 18 inch nuts and wash ers provided Refer to figures 12 and 13 Note When the EXT10 Exten Plates 1 amp 2 sion Pole will Tilting 4 _ Tilting be used attach Capability Capability the Outside Figure 13 Figure 16 Pole end to Plate 1 instead of Plate 2 using four 4 5 16 18 inch nuts and washers provided Refer to figure 14 MT20 Assembly con t Note When the EXT10 Extension Pole will be used attach the Inner Pole end to Plate 3 instead of Plate 2 using four 4 5 16 18 inch nuts and washers provided Refer to figure 17 6 Invert the projector and place it on a soft flat surface A
16. nvenience receptacles and the point where they exit from the apparatus CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of im portant operating and maintenance servicing instructions in the litera ture accompanying the appliance AV S RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL To prevent the risk of electric shock do not remove cover or 11 12 13 14 15 16 17 18 back No user serviceable parts inside Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manu facturer or sold with the appa ratus When a cart is used use caution when moving the cart ap paratus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service per sonnel Servicing is required when the ap paratus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids s
17. oceed to the LN9101M Lens Installa tion Ceiling Hex head EXT10 bolts and lock Extension nuts supplied Pole Kit with EXT10 6mm screws 6mm screw 1 4 20 tapped hole Figure 21 LN9101M Lens Installation Install the LN9101M Lens to the already functioning Projector by performing the steps below 1 Locate the previously set aside LN9101M Lens and place it on a flat surface oriented with the small Lens Cover facing up Refer to figure 22 2 Carefully remove the small cover from the Lens by screwing it counterclockwise it will take multiple Figure 20 3 The inner circumference of O1 T Orient the Lens Holder Lens turns Place the removed cover in a safe place for possible future use the Lens Holder is threaded to accept the Lens It is ex tremely important not to cross thread the Lens or Lens Holder when start ing the fastening process and do not over tighten Refer to figure 23 over the end of Lens Holder Mounting Post as illustrated in figures 24 and 25 Lower the Lens Holder Lens onto the top of the post and insert the previously removed Locking Ring in between the two ring type parts of the Lens Holder as it is lowered onto the post Figure 23 While holding the Lens Holder Lens about two Lens Holder Mounting Post Figure 24 Figure 25 inches from the top on Lens Holder Post insert the previously removed screw in the center of the Locking Ring and tighten Also
18. s to 24 inches as supplied If the default range is accept able proceed to Step 3 The adjustable range may be changed to 24 inches to 14 5 8 inches by cut ting both poles When the installation requires the 24 inches to 14 5 8 inches range proceed to Step 2 2 Cut the Outside Pole to 13 3 8 inches from the end the mount ing plate will be attached Cut the Inside Pole to 13 3 4 inches from the end the mounting plate will be attached Refer to figure 1 3 Attach the Bottom Mount ing Plate the flange with the wider space to the Outside Pole with two Round Head Philips 1 4 20 x 3 8 Screws In a similar manner attach the remain ing Plate to the Inside Pole Refer to figure 2 4 Assemble the Pole Pieces together making sure to orient them as illustrated in figure 3 on the next page Inside Pole Wi 0 0 Outside Pole 0 Cut Here Cut Here Figure 1 Figure 2 EXT10 Assembly con t 5 Set the Pole Pieces to the desired length and secure the posi tion using the two i Round Head Phil ii ips 1 4 20 x 2 1 4 Screws and two 1 4 n 20 Lock Nuts Refer DAN to figure 3 Tighten all the re cently install hard ware and proceed dp to assemble the Figure 3 LN9101M LN9101M Assembly Assemble the LN9101M by performing the steps below 1 N Orient the LN9101M Locate Plate 4 and the Top Adjust ment Plate from the L
19. tighten the other two screws located either side of the center screw on the Lock Ring Refer to figure 26 Note At this time do not be overly concerned about the exact position of the Lens The final Lens position will be set during the Lens Alignment procedure Remove the large Lens Cover from the front of the Lens by grasping both sides of the cover and pull ing straight forward Refer to figure 27 Proceed to Connecting the LN9101M Tighten Screws Large Lens Cover Insert Screw and Tighten Figure 27 Figure 26 Connecting the LN9101N Connecting the LN9101M to a Video System involves several connections Perform the following steps 1 Locate the external Power Supply supplied wth the LN9101M and connect the plug on the end of the cable to the 9V Jack on the LN9101M Sled Connection Plate Plug the CONSE Supply into an active AC Outlet Refer to figure 28 2 Connect a cable from the LN9101M 12V TRIG GER IN Jack to the Projector Trigger 2 Output Jack 3 Optionally connect the supplied External IR Sen sor to the LN9101M REMOTE IR IN Jack 4 Proceed to the LN9101M Alignment 1 12v Trigger outo Q a I 7 12v Trigger In oot 1 Figure 28 Penam he ane em to align the LN9101M Lens to the projector 1 Before the LN9101M Lens can be aligned it is important to complete the Initial Installation and Setup of the VP 11 Projector Refer to the User Guide of the VP 11 Projector and p
20. tional connection information refer to the owner s manual s for any component s connect ed to the LN9101M Anamorphic Lens System 3 The LN9101M Anamorphic Lens is designed to produce the best possible images when a curved Anamorphic Projection Screen is used contact your Marantz Dealer for additional information 4 The Anamorphic Lens is a precision optical device with special coatings just like you would find on Professional Cameras In the event the Lens re quires cleaning to remove airborne particles such as dust and dirt from the Lens use a safe cleaning product such as a clean and dry 3M Scotch Brite Microfiber Lens Cleaning Cloth At no time should ordinary household cleaning products be used to clean the Lens as damage will occur 5 To protect the lens surfaces from accidental dam age during the installation process DO NOT RE MOVE THE LENS COVERS UNTIL INSTRUCT ED 6 The LN9101M Motorized Sled uses bearings made from specialized permanently lubricated materials Keep the rail linear bearing clean dry and con taminant free Do not apply any lubricants to the Motorized Sled as this will gum up the mechanism and possibly produce a film on the projector and anamorphic lenses In case the LN9101M Sled is accidentally soiled i e spilled soda clean all contaminants with distilled water first and allow it to dry Then wipe it down with denatured alcohol The LN9101M should never be operated unless the
21. uch as vases are placed on the equipment To completely disconnect this equipment from the a c mains disconnect the power supply cord plug from the a c receptacle The mains plug of the power supply cord shall remain readily operable Do not expose batteries to excessive heat such as sunshine fire or the like e LS LA ADDITIONAL SAFETY INSTRUCTIONS WARNING THERE IS A POSSIBILITY OF SERIOUS INJURY IF YOU DO NOT FOLLOW THESE INSTRUCTIONS When mounting the projector to a building structure it is important to follow all of the local building construction codes The total weight of the Marantz VP 11 LN9101M Anamorphic Lens System and MT20 EXT10 Mounting Brackets is 80 Ibs 36 29 kg Make sure the ceiling structural members can support five times the total weight which is 400 Ibs 181 44 kg Proper installation procedure by qualified personnel as outlined in this installation guide is required It is recommended that the Profession als at your Marantz Dealer who are skilled in all aspects of installation and operation install the Marantz Video System and any associated audio equipment It is important to read this LN9101M Instal lation Guide and the VP 11 User Guide before starting the installation process The instructions in this Installation Guide must be adhered to as failure to do so could result in serious injury To prevent possible damage to the Lens As semblies DO NOT at any time attempt to LIFT
22. uctions supplied with the product c Repair or attempted repair by anyone not authorized by Marantz to repair the product d Any shipment of the product claims must be presented to the carrier e Any cause other than a product defect 2 Cleaning initial set up check ups with no defects found or charges incurred for installation removal or reinstallation of the product 3 Any product on which the serial number has been defaced modified or removed 4 Batteries 5 Accessories including but not limited to batteries cables mounting hardware and brackets cleaning accessories antenna and detachable power cords 6 Warranty is void if purchase was made from any one other than an authorized Marantz dealer Who may enforce the warranty Marantz America Inc EEE 100 Corporate Drive Mahwah N J 07430 2041 Phone 800 654 6633 Fax 201 762 6695 This warranty may be enforced only by the original purchaser What we will pay for We will pay for all labor and material expenses for items covered by the warranty Payment of shipping charges is discussed in the next section of this warranty How you can get service 1 If your unit needs service contact Marantz service referral by calling toll free 1 800 654 6633 We will advise you of the name and location of one or more authorized Marantz service stations from which service can be obtained Please do not return your unit to the factory without prior authorization
23. urved anamorphic screen some geometric distortion may be visible 9 Proceed to Operation The Marantz VP 11 Projector is designed to auto matically activate the LN9101M Lens when using the Remote Control supplied with the Projector How ever some of the Projector default settings must be changed for this to occur perform the following steps 1 Switch On the projector and press the MENU Push button on the Remote Control 2 Select the Conf Menu option and then change the default Trigger 2 settings to agree with the list below Trigger 2 Full Off Trigger 2 Normal Off Trigger 2 Zoom Off Trigger 2 V stretch On Trigger 2 Through Off 3 Exit the projector menu mode 4 When an Anamorphic Source is viewed press the ASPECT Ratio Push button until the V STRETCH Mode is selected using the Projectors Remote Control The LN9101M Lens will move into its active position in front of the projector lens 5 When viewing non Anamorphic Sources select one of the four other Aspect Ratios Full Normal Zoom or Through and the LN9101M Lens will move to its inactive position no longer in front of the projector lens Specifications Lens 1 33x 2 35 1 Cinemascope Motorized Sled Power Requirements 9 18V DC 0 5 1 5Amps Power Supply Adapter 100 240 VAC 0 2Amps Operating Temperature and Humidity 41 to 95 F 5 to 35 C 30 to 85 Overall Dimensions including Projector Width is 22 1 2 inches 57 2cm
Download Pdf Manuals
Related Search