Home

Makita 9045N Sander User Manual

image

Contents

1. Balt Bearing 6200LLB Abrasive Paper 114 150 Dust Bag Fastener MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase Should any trouble develop during this one year period return the COMPLETE tool freight prepaid to one of Makita s Factory or Authorized Service Centers If inspection shows the trouble is caused by defective workmanship or material Makita will repair or at our option replace without charge This Warranty does not apply where repairs have been made or attempted by others repairs are required because of normal wear and tear e The tool has been abused misused or improperly maintained e alterations have been made to the tool IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CON SEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A SPECIFIC PURPOSE AFTER THE ONE YEAR TERM OF THIS WARRANTY This Warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental
2. EJ y N FINISHING SANDER Thakita t DESCRIPTION te gy a aaa EM NO oescripTion TEM MO MACHINE MACHINE 1 2 Rivet 0 5 31 2 2 1 Name Plate 32 1 3 4 P H Screw MSx35 33 2 4 2 Carbon Brush 34 1 5 2 Brush Holder Cap 35 1 6 1 Slider Cover 36 1 7 1 Rubber Washer 37 4 8 1 Switch 9 1 FIELD ASSEMBLY 38 1 With Garter Spring x 2 39 1 10 1 Baffle Plate 40 2 11 1 Separate 41 2 12 1 Motor Housing 42 2 With Brush Holder x 2 amp S Screw MSx8 x 2 43 2 15 2 H Bolt M5x40 With Washer 44 1 16 2 Rubber Pin 4 45 1 17 1 P H Screw M4x12 With Washer 46 1 18 1 CORD ASSEMBLY 47 1 Assembled Cord Plug amp Cord Guard 19 1 Cord Guard 46 q 20 1 Strain Relief ag 1 21 2 P H Screw M4x18 With Washer 50 4 22 1 P H Screw M4x10 With Washer 51 1 23 1 Stopper 24 1 Frame 52 1 With Needle Bearing 810 53 1 25 1 Frame Cover 26 1 Poly V Belt 3 250 ACCESSORIES 27 1 V Pulley 3 26 aoe hs 28 1 Spindle F0 29 1 Key 4 402 1 30 2 Steel Band P H Screw M14x25 Rubber Sleeve P H Screw M4x30 With Washer Handle Cover Rubber Pin 6 Balance Weight Base With Sponge Rubber Ball Bearing 6002LLB Bearing Retainer 40 C H Screw M4x12 C H Screw M4x10 Push Button H Nut M4 Ball Bearing 6003DDU F Washer 26 F Washer 7 C H Screw M5x12 Bearing Retainer With Sponge Rubber Ball Bearing 608LB Insulation Washer ARMATURE ASSEMBLY Assembled Items 49 53 Fan 70
3. Finishing Sanden MODEL 9045N INSTRUCTION MANUAL Finishing Sander amp Standard Equipment Dust bag 2 Tool body Abrasive paper DOUBLE INSULATION Specifications Continuous Power Overall Pad size rating supply Input length cord P PARS E A aa Sie 114mm x 234 mm A10W 268 mm 2 5m 4 1 2 x 9 1 4 10 5 8 6 2 Ibs 8 2 ft Manufacturer reserves the right to change specifications of parts and accessories without notice Note Specifications of parts and accessories may vary from country to country IMPORTANT SAFETY INSTRUCTIONS WARNING When using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following READ ALL INSTRUCTIONS 1 2 10 11 12 13 14 15 16 17 KEEP WORK AREACLEAN Cluttered areas and benches invite injuries CONSIDER WORK AREA ENVIRONMENT Don t use power tools in damp or wet locations Keep work area well lit Don t expose power tools to rain Don t use tool in presence of flammable liquids or gases KEEP CHILDREN AWAY All visitors should be kept away from work area Don t let visitors contact tool or extension cord STORE IDLE TOOLS When not in use tools should be stored in dry and high or locked up place out of reach of children DON T FORCE TOOL It will do the job bet
4. l off the dust bag e Removing the frame cover Remove from either the front or back as shown when taking off the frame cover e Regular emptying of dust bag Regular emptying of the dust bag insures the maximum suction force A full bag makes for ineffective dust collection e Operation with coolant This tool can be used to sand with waterproof paper and a coolant but coolant should never be allowed to enter the motor area To use coolant first remove the dust bag and clean off any dust adhering to the tool Do a dry run for 2 or 3 minutes with the tool held off the surface in order to remove dust adhering to the dust chute area Then use only enough coolant to give good operation as excessive coolant can easily be splashed into the motor and markedly shorten motor life Coolant may also bridge parts which could result in a shock hazard eCommercial abrasive paper of the size 228 mm 9 x 280 mm 11 1 16 may be used by cutting it in half 228 mm 9 280 mm 11 1 16 Maintenance e Carbon brushes Replace carbon brushes when they wear down to about 6 mm 1 4 or spark ing will occur Both brushes should be changed at the same time 6mm 4 Optional accessories CAUTION The use of any other accessories not specified in this manual might be hazardous e Abrasive papers 742502 7 742503 5 742504 3 f 742505 1 10 Leh 3 Aes BB 7 oD N br S
5. or consequential damages so the above limitation or exclusion may not apply to you Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you z Makita Electric Wonka Ltd 11 8 3 chome Sumiyoshi cho Anjo Aichi 446 Japan 883130 062 B PRINTED IN JAPAN 1985 6 N
6. oubt DO NOT PLUG IN THE TOOL Using a power source with voltage less than the nameplate rating is harmful to the motor How to use e Attaching sandpaper To replace the sandpaper pul back on the lever clip to release the paper clamp below Dustproof frame cover must first be removed Insert the paper between the base and the paper clamp bending a por tion of about 20 mm 3 4 on both ends to make entry easier Then make sure that the paper is snugly fit to the pad with the right tension Failure to have it on tight will cause the paper to rip or mark the sanding surface e Switch There is a slide switch on the upper side of the tool handle Press it forward to put the tool on slip it backward to put the tool off e Sanding Lightly press the tool in such a manner that the entire pad surface contact uniformly the surface to be sanded Excessive pressure on the tool or one sided pressure may pro duce uneven surface cause damage to the abrasive paper and shorten tool life Do not allow the pad without abrasive paper to contact works surface or it will be damaged lessening its life e Dust bag attachment To install the dust bag fit the bag s entry port onto the dust chute on the right side of the sander then see that the small hole on the port fits over the pin protruding from the chute by turning left or right When removing the dust bag turn the bag to the left to slip the hole off the pin then simply pul
7. switch is OFF when plugging in OUTDOOR USE EXTENTION CORDS When tool is used outdoors use only exten sion cords intended for use outdoors and so marked STAY ALERT Watch what you are doing use common sense Don t operate tool when you are tired 18 CHECK DAMAGED PARTS Before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate proper ly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual Have defective switches replaced by authorized service center Don t use tool if switch does not turn it on and off 19 GUARD AGAINST ELECTRIC SHOCK Prevent body contact with grounded sur faces For example pipes radiators ranges refrigerator enclosures 20 REPLACEMENT PARTS When servicing use only identical replacement parts SAVE THESE INSTRUCTIONS VOLTAGE WARNING Before connecting the tool to a power source receptacle outlet etc be sure the voltage supplied is the same as that specified on the nameplate of the tool A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user as well as damage to the tool If ind
8. ter and safer at the rate for which it was intended USE RIGHT TOOL Don t force smal tool or attachment to do the job of a heavy duty tool Don t use tool for purpose not intended DRESS PROPERLY Don t wear loose clothing or jewelry They can be caught in moving parts Rubber gloves and non skid footwear are recommended when working outdoors Wear protective hair covering to contain long hair USE SAFETY GLASSES Also use face or dust mask if cutting operation is dusty DON T ABUSE CORD Never carry tool by cord or yank it to disconnect from re ceptacle Keep cord from heat oil and sharp edges SECURE WORK Use clamps or a vise to hold work It s safer than using your hand and it frees both hands to operate tool DON T OVERREACH Keep proper footing and balance at all times MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and charging accessories Inspect tool cords periodically and if damaged have repaired by authorized service facility Keep handles dry clean and free from oil and grease DISCONNECT TOOLS When not in use before servicing and when changing acces sories such as blades bits cutters REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on AVOID UNINTENTIONAL STARTING Don t carry plugged in tool with finger on switch Be sure

Download Pdf Manuals

image

Related Search

Related Contents

Bisomac 210 1-Phase Manual  Mode d`emploi Konftel 300W  Untitled - Emcotec  Honeywell HS-160R User's Manual  BELZONA 3131 Fiche Technique  D-304955 Installationsanleitung PowerMaster  Discovery 1 My95 - Manual De Reparaciones De Carroceria  I*I  

Copyright © All rights reserved.
Failed to retrieve file