LG Electronics -BKE 7630 NS G Air Conditioner User Manual
Contents
1. When cleaning the unit first make sure the power and breaker are turned off e Otherwise it may cause electrical shock Do not step on the indoor outdoor unit and do not put anything on it e It may cause an injury through dropping of the unit or falling down cord Turn off the main power switch when not using the product for a long time e Otherwise it may cause the failure of product or a fire Do not place a heavy object on the power e Otherwise it may cause a fire or electrical shock Owner s Manual 5 Safety Precautions When the product is submerged into water Take care so that children may not step on always contact the service center the outdoor unit e Otherwise it may cause a fire or electrical shock Otherwise children may be seriously injured due to falling down A CAUTION E Installation Install the drain hose to ensure that drain Install the product so that the noise or hot can be securely done wind from the outdoor unit may not cause any damage to the neighbors e Otherwise it may cause water leakage e Otherwise it may cause dispute with the neighbors Always inspect gas leakage after the Keep level parallel in installing the product installation and repair of product e Otherwise it may cause the failure of product e Otherwise it may cause vibration or water leakage 6 Room Air Conditioner Safety Precautions E Ope2. NANO Plasma Filter Signal rls Front Panel Power Cord Air Discharge Outdoor Air Intake Vents Connecting Wires Piping Drain Hose Base Plate Owner s Manual 9 Electrical Safety ie Electrical Safety A WARNING This appliance must be properly grounded To minimize the risk of electric shock you must alway plug into a grounded oulet Preferred method Ensure proper ground exists before use WARNING Do not cut or remove the grounding prong from the A power plug WARNING Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal and not insulated and the wall receptacle is grounded through the house wiring WARNING If you have any doubt whether the air conditioner is properly grounded have the wall receptacle and circuit checked by a qualified electrician 10 Room Air Conditioner Electrical Safety We strongly discourage the use of an adapter due to potential safety hazards For temporary connections use only a UL listed adapter available from most local hardware stores Ensure that the large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection To disconnect the power cord from the adapter use one hand on each to avoid damaging the ground terminal Avoid frequently unplugging the power cord as this can lead to eventual gr
3. The highest setting provides maximum cooling E The air filter is dirty e Clean the filter at least every 2 weeks See the care and Maintenance section Air 7 E The room may have been e When the air conditioner is first turned conditioner hot on you need to allow time for the Sia POLCON room to cool down as it should E Cold air is escaping e Check for open furnace floor registers and cold air returns E Cooling coils have iced up e See Air Conditioner Freezing Up below Air E Ice blocks the air flow and e Set the mode control at High Fan or conditioner stops the air conditioner from High Cool with thermostat at 1 or 2 freezing up cooling the room Owner s Manual 29
4. for service at all A PRECAUTION e Contact the authorized service technician for repair or maintenance of this unit e Contact the installer for installation of this unit e The air conditioner is not intended for use by young children or invalids without supervision e Young children should be supervised to ensure that they do not play with the air conditioner When the power cord is to be replaced replacement work shall be performed by authorized personnel only using only genuine replacement parts e Installation work must be performed in accordance with the National Electric Code by qualified and authorized personnel only 2 Room Air Conditioner Safety Precautions 7 Safety Precautions To prevent the injury of the user or other people and property damage the following instructions must be followed E Incorrect operation due to ignoring instruction will cause harm or damage The seriousness is classified by the following indications AWARN l NG This symbol indicates the possibility of death or serious injury A CAUTION This symbol indicates the possibility of injury or damage to properties only E The meanings of the symbols used in this manual are as shown below Be sure not to do Be sure to follow the instruction E Installation Always perform grounding Don t use a power cord a plug or a loose socket which is damaged e Otherwise it may cause electrical shock e Otherwise i
5. LG BEKO Air Conditioner OWNER S MANUAL MODELS LG BKE 7630 NS G LG BKE 7630 NS M LG BKE 7630 NSA Prior to installation this air conditioning unit must be submitted for approval by the utility service which provides electricity EN 61000 2 EN 61000 3 Norm IMPORTANT Please read this owner s manual carefully and thoroughly before installing and operating your room air conditioner Please retain this owner s manual for future reference after reading it thoroughly Room Air Conditioner Owner s Manual TABLE OF CONTENTS f FOR YOUR RECORDS Safety Precautions 00 3 Write the model and serial numbers here Model Prior to Operation ccccceeee 8 Sone You can find them on a label on the side of each unit Dealer s Name Introduction 9 Date Purchased S E Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues Electrical Safety cccce 10 READ THIS MANUAL I Inside you will find many helpful hints on how to use Operating Instructione 12 and maintain your air conditioner properly Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner Maintenance and Service PON AO 26 You ll find many answers to common problems in the chart of troubleshooting tips If you review our chart of Troubleshooting Tips first you may not need to call
6. direct airflow for a long time may be hazardous to your health Do not expose occupants pets or plants to direct airflow for a long time 2 Due to the possibility of oxygen deficiency ventilate the room when using the appliance together with stoves or other heating devices 3 Do not use this air conditioner for non specified special purpose e g preserving precision devices food pets plants or art objects Such use may damage your properties Cleaning and Maintenance 1 Do not touch the metal parts of the unit when removing the filter Injury can occur 2 Do not use water to clean inside the air conditioner Exposure to water can destroy the insulation leading to electric shock 3 When cleaning the unit first make sure that the power and breaker are turned off The fan rotates at a very high speed during operation There is a possibility of injury if the units power is triggered while cleaning inner parts of the unit Service For repair and maintenance contact your authorized service dealer 8 Room Air Conditioner Introduction 7 Introduction Symbols used in A This symbol alerts you to the risk of electric shock This symbol alerts you to hazards that may cause harm to the A air conditioner This symbol indicates special notes Features WARNING This appliance should be installed in accordance with national wiring A regulations This guide acts as a guide to help to explain product features Indoor
7. operating normally when You hear a pinging noise This is caused by water being picked up by the fan on rainy days or in highly humid conditions This feature is designed to help remove moisture in the air and improve cooling efficiency You hear the thermostat click This is caused by the compressor cycle starting and stopping You see water dripping from the rear of the unit Water may be collected in the base pan in highly humid conditions or on rainy days This water overflows and drips from the rear of the unit You hear the fan running while the compressor is silent This is a normal operational feature 28 Room Air Conditioner Maintenance and Service Troubleshooting The air conditioner may be operating abnormally when Possible Causes What To Do The air conditioner is e Make sure the air conditioner plug is unplugged pushed completely into the outlet E The fuse is blown circuit e Check the house fuse circuit breaker breaker is tripped box and replace the fuse or reset the Air breaker conditioner rs doesnot star E Power failure e If power failure occurs turn the mode control to Off When power is restored wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload E Airflow is restricted e Make sure there are no curtains blinds or furniture blocking the front of the air conditioner E The thermostat may not be e Turn the knob to a higher number set high enough
8. the door of the remote controller closed You can select the fan speed in four steps low medium high or CHAOS Each time the button is pressed the fan speed mode is shifted Air purifying operation NANO PLASMA can be with cooling Heating or any other operations NANO PLASMA Air Purifying Operation only If you press the only NANO PLASMA button only NANO PLASMA purification function operates Then fan speed is low You can select the fan speed in four steps low medium high or CHAOS Each time the button 5 is pressed the fan speed mode is shifted Owner s Manual 21 Operating Instructions 2nd F operation Press the Start Stop button The unit will respond with a beep Open the door of the remote control and press the 2nd Function button to operate functions printed in blue unter LILI buttons ummi Check the indication of 2nd function on the display of the remote controller These buttons can set the timer as follows a R OOO ON OFF SET O O a v O a 3 2nd function disappears in a short time automatically or when the button is pressed again For more details refer to functions next pages 22 Room Air Conditioner Operating Instructions Additional Ea Va Yo f ors a Cae Sleep mode A 1 Press the Sleep Mode Auto button to set the time you
9. want the unit to stop automatically 2 The Timer is programmed in one hour increments by pressing the Sleep Mode Auto button 1 to 7 times The sleep mode is available for 1 to 7 times To alter the time period in steps of 1 hour press the Sleep Mode Button while aiming at air conditioner 3 Make sure the Sleep Mode Auto LED lights up To cancel the Sleep Mode press the sleep Mode Auto button several times until the star Sev disappears from the operation display The Sleep Mode will be operated at slow fan speed cooling or medium fan speed heat pump only for a comfortable sleep In cooling mode or healthydehumidification mode The temperature will automatically rise by 1 C over the next 30 minutes and by 2 C in 1 hour for a comfortable sleep Setting the time 1 Time can be set only when you press the Reset button Having replacing the batteries you should press the reset buttons to reset the time Press the Start Stop button 2 Press 2nd F button and check if 2nd F icon is on 3 Press the Time Setting buttons until the desired time is set PR CANCEL 4 Press the Timer SET button ay OSE Check the indicator for A M and P M Delay start Pre set stop 1 Make sure the time is set correctly on the display of the remote controller 2 Press 2nd F button 3 Press the ON OFF Timer buttons to turn Timer on or off pecs 4 Press the Time Setting buttons until the desired time is set P 5 To set the select
10. Temp gt 24 C 21 C lt Room Temp lt 24 C Room Temp lt 21 C Healthy Dehumidification 20 Test operation During the TEST OPERATION the unit operates in cooling mode at high speed fan regardless of room temperature and resets in 18 minutes During test operation if remote controller signal is received the unit operates as remote controller sets lf you want to use this operation open the front panel upward and Press the power button let it be pressed for about 3 seconds lf you want to stop the operation re press the button Auto restart In case the power comes on again after a power failure Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions So there is no need of activating this function by pressing any key or button In the initial mode the fan operates at a low speed and the compressor starts 2 5 3 minutes later As the compressor starts the fan speed also resumes its previous setting mode Helpful information Fan speed and cooling capacity The cooling capacity indicated in the specification is the value when the fan speed is set to high and the capacity will be lower at low or medium fan speed High fan speed is recommended when you wish to cool the room quickly Owner s Manual 25 Maintenance and Service E Maintenance and Service Indoor Unit WARNING Turn the system off before cleaning To clean wipe with a soft dry cl
11. a x O Je 4 e e 9 JET T 0 on e o Ic gt Lh Lic miil miil miil Cooling Auto Healthy Heating changeover Dehumidification Heat pump model only Press the Jet Heat button to operate the speed heating mode and the unit will operate at super high fan speed on heating mode for 60 minutes To cancel the Jet Heat mode press the Jet Heat button the fan speed button or the room temperature setting button again and the unit will operate at high fan speed on heating mode p OB IS LW During the JET HEAT function at any moment the A C starts to blow the heat air at extremely high speed for 60 minutes setting the room temp automatically to 30 C It is especially used to heat the room temp quickly in a cool winter On cooling healthy dehumidification mode or auto changeover mode however the JET HEAT function is not available T In order to return to the normal heating mode from the JET HEAT mode just press the operation mode selection button airflow volume selection temp setting button or the JET HEAT button again 20 Room Air Conditioner Operating Instructions NANO PLASMA purification operation Optional Press the Start Stop button The unit will respond with a beep Open the door of the remote controller Press the NANO PLASMA button Operation will start when the button is pressed and stop when the button is pressed again Set the fan speed again with
12. appliances power cord power cord randomly e It will cause an electric shock or Otherwise it may cause a fire e Otherwise it may cause a fire a fire due to heat generation or electrical shock or electrical shock Take care so that the power Unplug the unit if strange Keep the flames away cord may not be pulled sounds smell or smoke during operation comes from it e Otherwise it may cause a fire e Otherwise it may cause e Otherwise it may cause a fire or electrical shock electrical shock or a fire os vy 4 Room Air Conditioner Take the power plug out if necessary holding the head of the plug and do not touch it with wet hands e Otherwise it may cause a fire or electrical shock vy a AAJN Do not allow water to run into electrical parts e Otherwise it may cause the failure of machine or electrical Do not use the power cord near the heating tools e Otherwise it may cause a fire and electrical shock Hold the plug by the head when taking it out e It may cause electric shock and damage Safety Precautions Do not open the suction inlet of the indoor outdoor unit during operation e Otherwise it may electrical shock and failure 4c Never touch the metal parts of the unit when removing the filter e They are sharp and may cause injury Ventilate the room well when using this appliance together with a stove etc e An oxygen shortage may occur
13. de by using a multiple lighting system 12 Room Air Conditioner Operating Instructions Remote Cont The controls will look like the following Controls 1 START STOP BUTTON D Operation starts when this button is pressed Signal transmitter and stops when the button is pressed again gt 2 OPERATION MODE SELECTION BUTTON Aox Used to select the operation mode 3 ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature 4 INDOOR FAN SPEED SELECTOR H Used to select fan speed in four steps lt C D low medium high and CHAOS 5 JET COOL HEATING OPTIONAL Sal aa e DAILY BE qa amy sit Sat fee ie angers D cooling heaing speed cooling heating operates 7 super high fan speed in cooling heatig mode OO 6 CHAOS SWING BUTTON iE 3 Used to stop or start louver movement and set the desired up down airflow direction 4 7 ON OFF TIMER BUTTONS 9 10 Used to set the time of starting and stopping 9 Operation See page 23 y 8 TIME SETTING BUTTONS 11 12 Used to adjust the time See page 23 8 17 9 TIMER SET CANCEL BUTTON 13 14 Used to set the timer when the desired time is obtained and to cancel the Timer 16 operation See page 23 10 SLEEP MODE AUTO BUTTON Used to set Sleep Mode Auto operation See page 23 11 AIR CIRCULATION BUTTON l Used to circulate the room air without 15 Flip up a cooling or heating See page 24 open
14. e system will not automatically switch from the cooling mode to the heating mode or from heating mode to cooling mode it must be done by manually resetting LW During Auto Operation pressing the chaos swing button makes the horizontal louvers swing up and down automatically If you want to stop auto swing press the chaos swing button again Owner s Manual 15 Operating Instructions Auto changeover operation Heat pump model only Press the Start Stop button The unit will respond with a beep Open the door of the remote controller To select Auto Changeover Operation press the Operation Mode Selection button Each time the button is pressed the operation mode is shifted in the direction of the arrow LL mutill a Fa oa 8 a7 e Ic 9 CE HL muii muii mii Cooling Auto Healthy Heating changeover Dehumidification Heat pump model only Close the door of the remote controller Set the temperature lower than the room temperature The temperature can be set within a range of 18 C 30 C at intervals of 1 C To raise the temperature To lower the temperature Set the fan speed again with the door of the remote controller still closed You can select the fan speed in four steps low medium high and CHAOS Each time the button is pressed the fan speed mode is shifted During Auto changeover Operation The air conditioner changes the operation mode automatica
15. ed 12 ROOM TEMPERATURE CHECKING BUTTON Operation Mode Used to check the room temperature 13 NANO PLASMA OPTIONAL Cooling Operation Used to start or stop the ay plasma purification function See page 21 14 HORIZONTAL AIRFLOW DIRECTION Auto Operation or Auto Changeover A CONTROL BUTTON OPTIONAL Uy Used to set the desired vertical airflow Healthy Dehumidification Operation ao ealthy Dehu ication Operation 15 RESET BUTTON y Used prior to resetting time Heating Operation 0 16 2nd F Button Used prior to using modes printed in blue e Cooling Model lt Heat Pump Model at the bottom of buttons See page 22 17 AUTO CLEAN OPTIONAL Used to set Auto Clean mode Owner s Manual 13 Operating Instructions 7A Cooling operation 1 Press the Start Stop button The unit will respond with a beep Open the door of the remote controller To select Cooling Operation press the Operation Mode Selection button Each time the button is pressed the operation mode is shifted in the direction of the arrow Oe rt L c auil auil Cooling Healthy Heating Dehumidification Heat pump model only Close the door of the remote controller Set the temperature lower than the room temperature The temperature can be set within a range of 18 C 30 C at intervals of 1 C To raise the temperature To lower the temperature Set the fan speed again with the door of the remote contro
16. ed time press the Timer setting button aiming the remote controller atthe Ss signal receptor CANCEL To cancel the timer setting Check if 2nd F icon is off CANCEL Press the Timer Cancel button aiming the remote controller at the signal receptor 5 The timer lamp on the air conditioner and the display will go out Select one of the following four types of operation wiahewnitrunnin Delay OFF Timer Delay ON Timer Delay OFF and ON Timer Delay ON and OFF Timer Owner s Manual 23 Operating Instructions Airflow direction control The up down and right left airflow can be adjusted by Press Chaos Swing button and the louvers will swing using the remote control a gt n Press the button again and the louvers will stop After 30 minutes the louvers return to the maximum airflow Press the Start Stop button to start the unit position automatically Air circulation mode Circulates the room air without cooling or heating 1 Press the Start Stop button the unit will respond with a beep 2 Open the door on the remote control Press the Air Circulation button Close the door on the remote control Now each time that you press the Indoor Fan Speed Selector the fan speed is shifted from low to CHAOS and back to low again m muii CHAOS Air Fan speed is on low Fan speed is on medium Fan speed is on high CHAOS Air economizes power consumption and prevents overco
17. ller still closed You can select the fan speed in four steps low medium high and CHAOS Each time the button is pressed the fan speed mode is shifted Natural wind by the CHAOS logic LI For fresher feeling press the Indoor fan speed selector and set to CHAOS mode In this mode the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic 14 Room Air Conditioner Operating Instructions Auto operation Cooling model only Press the Start Stop button The unit will respond with a beep Open the door of the remote controller To select Auto Operation press the operation mode selection button Each time the button is pressed the operation mode is shifted in the direction of the arrow ar Llc ae PLLA Cooling Healthy Heating Dehumidification Heat pump model only The temperature and fan speed are automatically set by the electronic controls based on the actual room temperature If you want to change the set temperature press the Room Temperature Setting buttons The cooler or warmer you feel the more times up to two times you should press the button The set temperature will be changed automatically To raise the temperature To lower the temperature During Auto Operation T You cannot control the indoor fan speed It has already been set by the Fuzzy rule Lilf the system is not operating as desired manually switch to another mode Th
18. lly to keep indoor temperature When room temperature vary over 2 C with respect to setting temperature air conditioner keeps the room temperature within 2 C with respect to setting temperature by auto changeover mode 16 Room Air Conditioner Operating Instructions Healthy dehumidification operation Press the Start Stop button The unit will respond with a beep Open the door of the remote controller To select Healthy Dehumidification Operation press the Operation Mode Selection button Each time the button is pressed the operation mode is shifted in the direction of the arrow am L miil amil Cooling Healthy Heating Dehumidification Heat pump model only Set the fan speed again with the door of the remote controller still closed D You can select the fan speed in four steps low medium high or CHAOS Each time the button is pressed the fan speed mode is shifted Natural wind by the CHAOS logic 11 For fresher feeling press the Indoor Fan Speed Selector and set to CHAOS mode In this mode the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic During Healthy Dehumidification Operation LW If you select the dehumidification mode on the operation selection button the A C starts to run the dehumidification function It automatically sets the room temp and airflow volume to the best condition for dehumidification based on the
19. oling The fan speed is automatically changed from high to low or vice versa depending on the ambient temperature Auto clean 1 Whenever you press the Auto Clean button Auto Clean Function will be reserved and cancelled 2 Auto Clean function works before and after cooling or dehumidification mode For details refer to AUTO CLEAN the below points 3 When the unit is started after the reservation of Auto Clean the Cool Start function operates and indoor Fan is started after 20 seconds 4 When you press Start Stop button to turn off the unit after the you have reserved Auto Clean function the air conditioner circulates the indoor air in the Auto Clean mode with no more Cooling or Dehumidification operation For Cooling only model it lasts for 30 minutes for Heat pump model for 16 minutes 5 If you press the auto clean button again during the product operation Auto Clean function will be cancelled LI During Auto Clean function moistures left in indoor units after Cooling Operation or Healthy Dehumidification Operation can be removed 4 During Auto Clean function only Start Stop button Plasma button and Auto Clean button are available 24 Room Air Conditioner Operating Instructions Forced operation Operation procedures when the remote control can t be used The operation will be started if the power button is pressed If you want to stop operation re press the button Heat pump Model Cooling Model Room
20. onds after opening the inlet grille it may cause electric shock Plasma Purifier Filter 3 Put the Plasma Filter into the neutral detergent for 1 2 hours and then raise it 4 Insert the Plasma Filter after perfectly drying it in shade Now insert Air Filter and close the front panel completely by matching the hook Front Panel Hook Hook Hanger Owner s Manual 27 Maintenance and Service Common Prot Before calling for service If you have problems with your air conditioner read the following information and try to solve the problem If you cannot find a solution turn off the air conditioner and contact your dealer Air conditioner does not operate 1 Ensure that the air conditioner is plugged into a proper outlet 2 Check the fuse or circuit breaker 3 Check whether the voltage is unusually high or low Air does not feel cold enough on the cooling setting 1 Ensure that the temperature settings are correct 2 Check to see if the air filter is clogged with dust If so replace the filter 3 Ensure that the air flow from the outside is not obstructed and that there is a clearance of over 20 between the back of the air conditioner and the wall or fence behind it 4 Close all doors and windows and check for any source of heat in the room Pp Before calling for service please review the following list of common problems and solutions The air conditioner is
21. oth Do not use bleach or abrasives Supply power must be disconnected before cleaning the indoor unit Air filter The air filters behind the front grill should be checked and cleaned once every 2 weeks or more often if neccessary 1 Lift the front panel After lifting up the filter tab a bit take the filter out slowly Clean the filter after stopping the product 2 Clean the filter with a vacuum or warm soapy water e If dirt is conspicuous wash with a solution of detergent in lukewarm water e If hot water 40 C or more is used it may be deformed 3 After washing with water dry well in the shade 4 Re install the air filter Never use any of the followings e Water hotter than 40 C Could cause deformation and or discoloration e Volatile substances Could damage the surfaces of the air conditioner Gasoline The heat exchanger coils and panel vents of the outdoor unit should be checked regularly If clogged with dirt or soot the heat exchanger and panel vents may be professionally steam cleaned Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs Air outlet vents 26 Room Air Conditioner Maintenance and Service e Recomended use period About 3 months 1 Lift the front panel hold it up and pull the Air filter Front Panel 2 Remove the Plasma Filter WARNING Don t touch the PLASMA Filter within 10 sec
22. ound terminal damage Temporary method Receptacle Cover We strongly discourage the use of an extension cord due to potential safety hazards For temporary situations use only CSA certified and UL listed 3 wire grounded extension cords rated 15 A 125 V Owner s Manual 11 Operating Instructions 7 Operating Instructions How to insert the 1 Remove the battery cover by pulling it according to the arrow direction 2 Insert new batteries making sure that the and of battery are installed correctly 3 Reattach the cover by sliding it back into position Woj Use 2 AAA 1 5volt batteries Do not use rechargeable batteries e The remote controller may be stored by mounting e To operate the room air conditioner aim the iton a wall Signal receptor remote controller at the signal receptor Receives the signals from the remote controller Signal receiving sound two short beeps or one long beep Operation indicating lamps A On or xe Sleep Mode Timer Defrost Mode operation yy Nano Plasma Lights up during the system operation Lights up during Sleep Mode Auto operation Lights up during Timer operation Lights up during Defrost Mode or Hot Lights up during outdoor unit operation Start operation Heat pump model only Operation indicating Cooling model only lamps The function illustrates its dynamic mo
23. ration Avoid excessive cooling Use a soft cloth to clean Do When gas leaks open the and perform ventilation not use wax thinner or a window for ventilation sometimes strong detergent before operating the unit e Otherwise it may do harm to e The appearance of the air e Otherwise it may cause your health conditioner may deteriorate explosion and a fire change color or develop surface flaws Do not use an appliance for Do not place obstacles Always insert the filter special purposes such as around the flow inlet or securely Clean it every two preserving animals outlet weeks vegetables precision machine or art articles e Otherwise it may damage your Otherwise it may cause the e Operation without the filter will properties failure of appliance or an cause failure accident Do not insert the hands or bars through the Do not drink water coming out of the air air inlet or outlet during operation conditioner e Otherwise it may cause personal injury e Otherwise it may cause stomachache Owner s Manual 7 Prior to Operation Preparing for Operation 1 Contact an installation specialist for installation 2 Plug in the power plug properly 3 Use a dedicated circuit 4 Do not use an extension cord 5 Do not start stop operation by plugging unplugging the power cord 6 If the cord plug is damaged replace it with only an authorized replacement part Usage 1 Being exposed to
24. sensed current room temp In this case however the setting temp is not displayed on the remote controller and you are not able to control the room temp either 4 During the healthy dehumidification function the airflow volume is automatically set according to the optimization algorithm responding to the current room temp status so that the room condition is kept healthy and comfortable even in the very humid season Owner s Manual 17 Operating Instructions cq Heating operation Heat pump model only Press the Start Stop button The unit will respond with a beep Open the door of the remote controller To select Heating e Operation press the Operation Mode Selection button i Each time the button is pressed the operation mode is mH h 3 shifted in the direction of the arrow umi i oe we X i mumi mui m Heating Cooling Healthy Heat pump model only Dehumidification Close the door of the remote controller Set the temperature higher than the room temperature The temperature can be set within a range of 16 C 30 C at intervals of 1 C To raise the temperature To lower the temperature Set the fan speed again with the door of the remote controller still closed You can select the fan speed in four steps low medium high and CHAOS Each time the button is pressed the fan speed mode is shifted Natural wind by the CHAOS logic Li For fresher feeling press
25. t may cause a fire or electrical shock ink For installation of the product always Securely attach the electrical part cover to contact the service center or a professional installation agency e Otherwise it may cause a fire electrical shock explosion or injury the indoor unit and the service panel to the outdoor unit e If the electrical part cover of the indoor unit and the service panel of the outdoor unit are not attached securely it could result in a fire or electric shock due to dust water etc Owner s Manual 3 Safety Precautions Always install an air leakage Do not keep or use Ensure that an installation breaker and a dedicated flammable gases or frame of the outdoor unit is switching board combustibles near the air not damaged due to use for conditioner a long time e No installation may cause a fire Otherwise it may cause a fire e It may cause injury or an and electrical shock or the failure of product accident SSS JC cee lt IA Do not disassemble or Do not install the product at Use caution when repair the product a place that ther is concern unpacking and installing randomly of falling down e It will cause a fire or electrical e Otherwise it may result in e Sharp edges may cause injury shock personal injury E Operation Do not share the outlet with Do not use the damaged Do not modify or extend the other
26. the Indoor Fan Speed Selector and set to CHAOS mode In this mode the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic 18 Room Air Conditioner Operating Instructions 3 Jet cool operation Press the Start Stop button The unit will respond with a beep Press the Jet Cool button to operate the speed cooling mode and the unit will operate at super high fan speed ET on cooling mode for 30 minutes To cancel the Jet Cool mode press the Jet Cool button the fan speed button or the room temperature setting button again and the unit will operate at high fan speed on cooling L During the JET COOL function at any moment the A C starts to blow the cool air at extremely high speed for 30 minutes setting the room temp automatically to 18 C It is especially used to cool the room temp quickly in a hot summer In heat pump mode neuro fuzzy mode or auto changeover mode however the JET COOL function is not available 11 In order to return to the normal cooling mode from the JET COOL mode just press the operation mode selection button airflow volume selection temp setting button or the JET COOL button again Owner s Manual 19 Operating Instructions Jet heat operation Optional Press the Start Stop button The unit will respond with a beep Open the door of the remote controller To select Heating Operation
Download Pdf Manuals
Related Search