Home

Lenovo 3656 Personal Computer User Manual

1. Figure 2 Rear connector locations Voltage selection switch some models Power cord connector PS 2 mouse connector PS 2 keyboard connector DVI monitor connector Parallel port VGA monitor connector EJ USB connectors 4 E Ethernet connector USB connectors 2 Microphone connector Audio line out connector Audio line in connector PCI Express x1 card slot PCI Express x16 graphics card slot PCI card slots 2 Serial port some models NOGBENE SEBBEREE SI Ea E D La Ke Chapter 1 Product overview 9 10 User Guide Connector Audio line in connector Audio line out connector DVI monitor connector Ethernet connector Microphone connector Parallel port Serial port PS 2 keyboard connector PS 2 mouse connector USB connector VGA monitor connector Description Used to receive audio signals from an external audio device such as a stereo system When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording devices Used to attach a DVI monitor or other devices that use a DVI monitor connector Used to attach an Ethernet cable for a local are
2. This section provides instructions on how to replace the secondary hard disk drive 30 User Guide To replace the secondary hard disk drive 1 afk oN Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Remove the computer cover See Removing the computer cover on page 16 Locate the secondary hard disk drive See Figure 5 on page 13 Disconnect the signal and power cables from the hard disk drive Press the blue release button to release the hard disk drive cage from the chassis Figure 21 Removing the secondary hard disk drive 6 Remove the hard disk drive cage from the chassis by simply sliding it outward Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage Remove the hard disk drive from the blue plastic bracket by flexing the sides of the bracket enough to slide it free from the hard disk drive Chapter 2 Installing or replacing hardware 31 32 User Guide 9 To install anew hard disk drive into the blue bracket flex the bracket and align pin H pin H pin Bf and pin H on the bracket with the holes in the hard disk drive Do not touch the circuit board on the bottom of the hard disk drive Figure 22 Installing the secondary hard disk drive into the bracket 10 Slide the ne
3. 6 User Guide Power Manager The Power Manager program provides convenient flexible and complete power management for your ThinkCentre computer By using the Power Manager program you can adjust your power settings to achieve the best balance between system performance and power saving Factory Recovery The Factory Recovery program enables you to restore the contents of the hard disk drive to the factory default settings ThinkVantage System Update The ThinkVantage System Update TVSU program helps you keep the software on your computer up to date by downloading and installing software packages ThinkVantage applications device drivers BIOS updates and other third party applications Some examples of software that you should keep updated are programs provided by Lenovo such as the Rescue and Recovery program and the ThinkVantage Productivity Center program Fingerprint Software The integrated fingerprint reader provided on some keyboards works with the Fingerprint Software program to enable you to enroll your fingerprint and associate it with your Windows password As a result fingerprint authentication can replace your password and enable simple and secure user access A fingerprint reader keyboard is available with certain computers or can be purchased for computers that support this option Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox program helps you maintain your computer improve computing security diagn
4. Attention If you restore the hard disk drive from a Rescue and Recovery backup or restore the hard disk drive to the factory default settings all files on the primary hard disk drive partition usually drive C will be deleted in the recovery process If possible make copies of important files If you are unable to start the Windows operating system you can use the Rescue files feature in the Rescue and Recovery workspace to copy files from your hard disk drive to other media To start the Rescue and Recovery workspace do the following 1 Make sure the computer is turned off 2 Repeatedly press and release the F11 key when turning on the computer When you hear beeps or see a logo screen release the F11 key If you have set a Rescue and Recovery password type your password when prompted The Rescue and Recovery workspace opens after a short delay Note If the Rescue and Recovery workspace fails to open see Solving recovery problems on page 58 Do one of the following To rescue files from your hard disk drive or from a backup click Rescue files and follow the instructions on the screen e To restore your hard disk drive from a Rescue and Recovery backup or to restore your hard disk drive to the factory default settings click Restore your system and follow the instructions on the screen For more information about the features of the Rescue and Recovery workspace click Help Notes 1 After restoring a ha
5. on page 16 Disconnect the signal and power cables from the rear of the optical drive w 4 Press the blue release button and remove the optical drive out of the front of the computer Note There is a spare retainer bracket attached to the side of the upper drive cage Figure 24 Removing the optical drive 5 Remove the retainer bracket from the drive being replaced and install it on a new drive To i i I Figure 25 Retainer bracket for optical drive 6 Slide the new optical drive into the bay from the front until it snaps into position 7 Connect the signal and power cables to the drive 8 Go to Completing the parts replacement on page 45 34 User Guide What to do next e To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on eral 45 Replacing the diskette drive or card reader Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the diskette drive or card reader Depending on your model type your computer might have a diskette drive or a
6. 8 When prompted to change the machine type model press Y Type in the seven character machine type model of your computer and then press Enter Follow the instructions on the screen to complete the update Updating flashing the BIOS from your operating system Note The Web page content including the links referenced in the following procedure is subject to change because of the constant improvements made to the Web site Go to http www lenovo com support Locate the Downloadable files for your machine type as follows a In the Enter a product field type your machine type b Click Go gt Continue gt Downloads and drivers c Under the BIOS category click the Flash BIOS update d Click the TXT file that contains the installation instructions for the flash BIOS update flash from the operating system version Print these instructions This is very important because they are not on the screen after the download begins From your browser click Back to return to the list of files Carefully follow the printed instructions to download extract and install the update Recovering from a POST BIOS update failure 64 User Guide If the power to your computer is interrupted while the POST BIOS is being updated flash update your computer might not restart correctly If this happens perform the following procedure which is commonly called Boot block recovery 1 Turn off the computer and any attached d
7. Figure 8 Opening the PCI card latch 4 If you are installing a PCI card remove the appropriate PCI card slot cover If you are replacing a PCI card locate the appropriate PCI card slot on the system board and remove the old PCI card that is currently installed Notes a The PCI card fits tightly into the PCI card slot If necessary alternate moving each side of the PCI card a small and equal amount until it is completely removed from the PCI card slot Chapter 2 Installing or replacing hardware 19 b If the PCI card is secured in place by a retaining latch f press the retaining latch to release the PCI card from the latch Then grasp the PCI card by the edges and carefully pull it out of the slot 5 Remove the PCI card from its static protective package 6 Install the new PCI card into the appropriate PCI card slot on the system board Then pivot the PCI card latch to the closed position to secure the PCI cards Figure 9 Closing the PCI card latch 7 Reinstall all parts and reconnect all cables that have been removed What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on age 45 45 20 User Guide Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the Important safety informati
8. P N 89Y0418
9. on page 56 e Use a recovery medium if you want to restore the system drive or the hard disk drive to the factory default settings See Creating and using recovery media on Note If you are unable to access the Rescue and Recovery workspace or the Windows environment from a rescue medium a recovery repair diskette or a recovery medium you might not have the rescue device diskette drive or recovery device set as the first boot device in the startup device sequence For more information see Setting a rescue device in the startup sequence It is important to create a rescue medium a recovery repair diskette and a recovery medium as early as possible and store them in a safe place Chapter 4 Using the Setup Utility The Setup Utility program is used to view and change the configuration settings of your computer regardless of which operating system you are using However the operating system settings might override any similar settings in the Setup Utility program Starting the Setup Utility program To start the Setup Utility program do the following 1 Make sure your computer is turned off 2 Repeatedly press and release the F1 key when turning on the computer When you hear multiple beeps or see a logo screen release the F1 key Note If a user password or an administrator password has been set the Setup Utility program menu is not displayed until you type your password For more information see Using
10. operating systems and application programs network setup and configuration upgraded or extended hardware repair services and custom installations Service availability and service name might vary by country or region For more information about these services go to http www lenovo com Appendix Notices Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services currently available in your area Any reference to a Lenovo product program or service is not intended to state or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to Lenovo United States Inc 1009 Think Place Building One Morrisville NC 27560 U S A Attention Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLI
11. Doctor for Rescue and Recovery 5 te se 4 69 PC Doctor for DOS 2 2 70 Cleaning the mouse c s s 70 Optical mouse e e 70 Non optical mouse 2 71 Chapter 7 Getting information N and service a 7 Information resources 2 73 Online Books folder 2 73 Lenovo ThinkVantage Tools 7 ThinkVantage Productivity Center 74 Lenovo Welcome 74 Access Help s e os e 2 nn son o 74 Safety and Warranty 74 Lenovo Web site http www lenove com 74 Help and service 2 ancs e 1D iii Using the documentation and diagnostic programs Calling for service Using other services Purchasing additional services Appendix Notices iv User Guide 75 79 76 76 77 Television output notice Trademarks Index 78 78 79 Important safety information CAUTION Before using this manual be sure to read and understand all the related safety information for this product Refer to the ThinkCentre Safety and Warranty Guide that you received with this product for the latest safety information Reading and understanding this safety information reduces the risk of personal injury and or damage to your product If you no longer have a copy of the ThinkCentre Safety and Warranty Guide you can obtain a Portable Document Format PDF version from the Lenov
12. assembly CAUTION A A The heat sink and fan assembly might be very hot Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover To replace the heat sink and fan assembly 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 3 Lay the computer on its side 4 Locate the heat sink and fan assembly See Locating parts on the system board on page 12 Chapter 2 Installing or replacing hardware 25 5 Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system board 6 Pivot the handle to release the heat sink and fan assembly clamp and then disengage the clamp from the plastic retention bracket Figure 16 Removing the heat sink and fan assem
13. card reader installed The artwork in this section shows how to replace the diskette drive To replace the card reader the procedure is almost the same as replacing the diskette drive To replace the diskette drive or card reader 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 3 Remove the front bezel See Removing and reinstalling the front bezel on 4 Disconnect the signal and power cables from the rear of the diskette drive or card reader Chapter 2 Installing or replacing hardware 35 5 Press the release button and slide the diskette drive or card reader out of the front of the computer Figure 26 Removing the diskette drive or card reader 6 Remove the retainer bracket from the failing diskette drive or card reader and install it on a new diskette drive or card reader Figure 27 Retainer bracket for diskette drive or card reader 7 Slide the new diskette drive or card reader into the drive bay until it snaps into position 8 Connect the flat cable to the new diskette drive or card reader 9 Reinstall the front bezel 10 Go to Completing the parts replacement on page 45 M What to do next To work with another opti
14. computer cover See Removing the computer cover on page 16 Locate the rear fan assembly See Locating components on page 11 Disconnect the rear fan assembly cable from the system fan connector on the system board See Locating parts on the system board on page 12 The rear fan assembly is attached to the chassis by four rubber mounts Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis Figure 30 Removing the rear fan assembly 6 Install the new rear fan assembly by aligning the new rubber mounts of the new rear fan assembly with the holes on the chassis and push the rubber mounts through the holes Note The new rear fan assembly you received will have four new rubber mounts attached Chapter 2 Installing or replacing hardware 39 7 Pull on the tips of the rubber mounts until the rear fan assembly is in place Figure 31 Installing the rear fan assembly 8 Connect the rear fan assembly cable to the system fan connector on the system board 9 Go to Completing the parts replacement on page 45 r What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on TAa Replacing the front audio and USB assembly Attention Do not open your computer or att
15. increase storage capacity and enable your computer to read other types of media Internal drives are installed in bays In this manual the bays are referred to as bay 1 bay 2 and so on When installing or replacing an internal drive it is important to note the type and size of the drive that you can install or replace in each bay and correctly connect 12 User Guide the cables to the drive installed Refer to the appropriate section in Chapter 2 Installing or replacing hardware on page 15 for instructions on how to install or replace internal drives for your computer Figure 5 shows the locations of the drive bays Figure 5 Drive bay locations Bay 1 Optical drive bay with an optical drive installed H Bay 2 Optical drive bay Bay 3 Diskette drive or card reader available in some models El Bay 4 Primary SATA hard disk drive bay with a 3 5 inch SATA hard disk drive installed H Bay 5 Secondary SATA hard disk drive bay with a 3 5 inch SATA hard disk drive installed in some models Chapter 1 Product overview 13 14 User Guide Chapter 2 Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer Handling static sensitive devices Do not open the static protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part Static electr
16. or your user name Not be a common word or a common name Be significantly different from your previous password User Password When a User Password is set the computer cannot be used until a valid password is typed in Administrator Password When an Administrator Password is set it deters unauthorized people from changing configuration settings If you are responsible for maintaining the settings of several computers you might want to set an Administrator Password After you set an Administrator Password a password prompt is displayed each time you try to access the Setup Utility program If both the user and administrator passwords are set you can type either password However to change any configuration settings you must use your administrator password Setting changing and deleting a password To set change or delete a password do the following Note A password can be any combination of up to 12 1 to 12 alphabetic and numeric characters For more information i eRe CET 1 Start the Setup Utility program see Chapter 4 Using the Setup Utility on page 59 2 From the Setup Utility program menu select Security 3 Based on your need select Set User Passwords or Set Administrator Passwords 4 Read the information displayed on the right side of the screen Enabling or disabling a device 60 User Guide You can enable or disable user access to a device SATA 1 When this feature is set
17. program help system Note If you encounter failures that prevent you from gaining access to the Rescue and Recovery workspace you can run the PC Doctor for Rescue and Recovery diagnostic program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace See Creating and using rescue media on page 55 Chapter 6 Troubleshooting and diagnostics 69 PC Doctor for DOS You can also download the latest version of the PC Doctor for DOS diagnostic program from http www lenovo com support The PC Doctor for DOS diagnostic program runs independently of the Windows operating system Use the PC Doctor for DOS diagnostic program if you are unable to start the Windows operating system or if the two diagnostic programs preinstalled on your computer have not been successful in isolating a possible problem You can run the PC Doctor for DOS diagnostic program from a diagnostic disc that you created Creating a diagnostic disc This section provides instructions on how to create a diagnostic disc To create a diagnostic disc do the following 1 Download a self starting bootable CD DVD image known as an ISO image of the diagnostic program from http www lenovo com support 2 Use any CD DVD burning software to create a diagnostic disc with the ISO image Running the diagnostic program from a diagnostic disc This section provides instructions on how to run the diagn
18. there is a smudge on the lens gently clean the area with a plain cotton tipped swab b If there is debris in the lens gently blow the debris away from the area Check the surface on which you are using the mouse If you have a very intricate picture or pattern beneath the mouse it may be difficult for the digital signal processor DSP to determine changes in the mouse position Reconnect the mouse cable to the computer Turn your computer back on Non optical mouse The non optical mouse uses a ball to navigate the pointer If the pointer on the screen does not move smoothly with the mouse you might need to clean the mouse 2 4 To Retainer ring Ball Plastic rollers Ball cage clean the non optical mouse do the following Note The following illustration might be slightly different from your mouse 1 2 3 Turn off your computer Disconnect the mouse cable from the computer Turn the mouse upside down Twist the retainer ring to the unlocked position to remove the ball Place your hand over the retainer ring and ball H and then turn the mouse right side up so that the retainer ring and ball fall out into your hand Wash the ball in warm soapy water then dry it with a clean cloth Chapter 6 Troubleshooting and diagnostics 71 72 User Guide 1 12 Blow air carefully into the ball cage J to dislodge dust and lint Look for a buildup of dirt on the plastic rollers inside the ball cage This bui
19. to Disable all devices connected to the SATA controller such as hard disk drives or the CD ROM drive are disabled and will not be displayed in the system configuration OnBoard Floppy When this feature is set to Disable the diskette drive cannot be Controller accessed To set the SATA 1 do the following 1 Start the Setup Utility program see Starting the Setup Utility program on page 59 2 From the Setup Utility program menu select Devices gt SATA Drives Setup gt SATA 1 and press Enter Select 32 Bit Data Transfer Select the desired settings and press Enter gt o 5 Return to the Setup Utility program menu and select Exit gt Save Changes and Exit Note If you do not want to save the settings select Discard Changes or Discard Changes and Exit To set the OnBoard Floppy Controller do the following 1 Start the Setup Utility program see Starting the Setup Utility program on page 59 2 From the Setup Utility program menu select Devices gt Floppy Drive Setup gt OnBoard Floppy Controller 3 Select the desired settings and press Enter 4 Return to the Setup Utility program menu and select Exit gt Save Changes and Exit Note If you do not want to save the settings select Discard Changes or Discard Changes and Exit Selecting a startup device If your computer does not start up from a device such as the CD ROM diskette or hard disk drive as expected use one of the follow
20. v safety information 74 security cable lock 47 features 3 46 padlock 48 selecting start up device 61 temporary startup device 61 serial port 10 service and help 75 customer support center 75 getting 73 services other 76 purchasing additional 76 setting password 60 rescue device 58 settings changing 59 viewing 59 Setup Utility 59 Setup Utility program starting 59 Setup Utility exiting 62 software recovering 51 software overview 5 solving recovery problems 58 starting the Setup Utility program 59 startup device 61 sequence changing 62 temporary selecting 61 static sensitive devices handling 15 system management 2 programs 63 system board connectors 12 identifying parts 12 location 12 memory module 21 T television output notice 78 temporary startup device 61 ThinkVantage Productivity Center 74 trademarks 78 troubleshooting basic 67 troubleshooting diagnostics 67 U updating flashing the BIOS 63 system programs 63 updating flashing the BIOS 64 USB connector 10 user password 60 using diagnostic programs 75 documentation 75 other services 76 passwords 59 recovery repair diskette creating and using 56 rescue media creating and 55 Setup Utility 59 V VGA monitor connector 10 video subsystem 1 viewing and changing settings 59 W warranty information 74 workspace backup and recovery 54 Index 81 82 User Guide lenovo Part Number 89Y0418 Printed in USA 1P
21. ED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product specifications or warranties Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve a
22. Eon Handling static sensitive devices Installing or replacing hardware Installing external options Removing the computer cover P Removing and reinstalling the front bezel Installing or replacing a PCI card Installing or replacing a memory module Replacing the battery Replacing the power supply assembly Replacing the heat sink and fan assembly Replacing the primary hard disk drive Replacing the secondary hard disk drive Replacing the optical drive Replacing the diskette drive or card redder Replacing the front fan assembly Replacing the rear fan assembly Replacing the front audio and USB assembly Replacing the internal speaker Replacing the keyboard Replacing the mouse Completing the parts replacement Installing security features Integrated cable lock Padlock Password protection Erasing lost or forgotten passwords clearing CMOS bar Aue Su Chapter 3 Recovery information Creating and using recovery media Creating recovery media Using recovery media Performing backup and recovery operations Performing a backup operation Performing a recovery operation Using the Rescue and Recovery workspace Creating and using rescue media Copyright Lenovo 2008 2009 9 15 15 15 15 16 18 18 21 22 24 25 27 30 38 35 37 38 40 42 43 45 45 46 47 48 48 48 51 Sl 51 82 58 gt 53 53 54 55 Creating rescue med
23. PS 2 keyboard connector or a USB connector FA Depending on where your keyboard is connected Figure 35 Keyboard connectors 3 Disconnect the failing keyboard cable from the computer 4 Connect a new keyboard to the appropriate connector on the computer 5 Go to Completing the parts replacement on page 45 44 User Guide Replacing the mouse Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the mouse To replace the mouse 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Locate the connector for the mouse Note Your mouse might be connected to a PS 2 mouse connector ora USB connector FA Depending on where your mouse is connected see Locating connectors on the rear of your computer on page 9lor Locating connectors on the front of your computer on page 8 ad Figure 36 Mouse connectors 3 Disconnect the failing mouse cable from the computer 4 Connect a new mouse ca
24. Rear fan assembly Power supply assembly Chapter 1 Product overview 11 Locating parts on the system board Figure 4 shows the location of the parts on the system board Tor gy E ee mm Figure 4 System board parts locations 4 pin power connector El System fan connector Microprocessor fan connector E Microprocessor and heat sink 5 Memory slots 4 H 24 pin power connector Thermal sensor connector E Diskette drive connector E Cover presence Intrusion switch connector SATA connectors 4 Power fan connector Front panel connector Locating internal drives mm Internal speaker connector Front USB connector 2 Clear CMOS Complementary Metal Oxide Semiconductor Recovery jumper Front USB connector 1 Serial COM2 connector Serial COMI connector CD IN connector H Front audio connector PCI card slots 2 PCI Express x16 graphics card slot p grap PCI Express x1 card slot 24 Battery Internal drives are devices that your computer uses to read and store data You can add drives to your computer to
25. Windows Vista e Microsoft Windows XP Professional preinstalled through downgrade rights in Windows 7 Professional Windows Vista Business or Windows Vista Ultimate Operating system s certified or tested for compatibility varies by model type e Linux 1 The operating system s listed here are being certified or tested for compatibility at the time this publication goes to press Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this manual This list is subject to change To determine if an operating system has been certified or tested for compatibility check the Web site of the operating system vendor Chapter 1 Product overview 3 Specifications This section lists the physical specifications for your computer Dimensions Width 175 mm 6 9 inches Height 402 mm 15 8 inches Depth 440 mm 17 3 inches Weight Maximum configuration as shipped 11 kg 24 Ibs Environment Air temperature Operating 10 to 35 C 50 to 95 F Non operating 40 to 60 C 40 to 140 F Humidity Operating 10 to 80 10 per hour non condensing Non operating 10 to 90 10 per hour non condensing Maximum altitude Operating 50 to 10 000 ft 15 2 to 3 048 m Non operating 50 to 35 000 ft 15 2 to 10 668 m Electrical input Input voltage Low range Minimum 100 V ac Maximum 127 V ac Input frequency range 50 60 Hz Voltage selection sw
26. a network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to attach a microphone to your computer when you want to record sound or if you use speech recognition software This connector might be located on the front of the computer Used to attach a parallel printer a parallel scanner or other devices that use a 25 pin parallel port Used to attach an external modem a serial printer or other devices that use a 9 pin serial port Used to attach a keyboard that uses a PS 2 keyboard connector Used to attach a mouse trackball or other pointing devices that use a PS 2 mouse connector Used to attach a device that requires a Universal Serial Bus USB connector such as a USB keyboard a USB mouse a USB scanner or a USB printer If you have more than eight USB devices you can purchase a USB hub which you can use to connect additional USB devices Used to attach a VGA monitor or other devices that use a VGA monitor connector Locating components To remove the computer cover see Removing the computer cover on page 16 Figure 3 shows the location of the various components in your computer Figure 3 Component locations Heat sink and fan assembly H Memory modules Battery El PCI Express x16 graphics card slot E PCI card installed in some models J PCI card slot PCI Express x1 card slot H Cover presence Intrusion switch E
27. ailable on the Lenovo Support Web site at http www lenovo com support Notes 1 The publications are in Portable Document Format PDF To view the publications you need to have the Adobe Reader program preinstalled on your computer If the Adobe Reader program has not been installed on your computer a message will appear when you attempt to view the PDF file and you will be guided through the Adobe Reader program installation 2 The publications are available in other languages on the Lenovo Support Web site at http www lenovo com support 3 If you want to install a different language version of the Adobe Reader program rather than the version preinstalled on your computer download the language version you want from the Adobe Web site at http www adobe com Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely Note The Lenovo ThinkVantage Tools program is only available on computers with the Windows 7 operating system from Lenovo To access the Lenovo ThinkVantage Tools program click Start gt All Programs gt Lenovo ThinkVantage Tools Copyright Lenovo 2008 2009 73 ThinkVantage Productivity Center Note The ThinkVantage Productivity Center program is only available on computers preinstalled with the Windows Vista operating system or the Windows XP operating syst
28. an operational state after all other methods of recovery have failed As a precautionary measure it is important to create recovery media as soon as possible Note The recovery operations you can perform using recovery media vary depending on the operating system from which they are created Your Microsoft Windows license permits you to create only one data medium so it is important that you store the created recovery medium in a safe place Creating recovery media This section provides instructions on how to create recovery media on different operating systems Note On the Windows 7 operating system you can create recovery media using discs or external USB storage devices On the Windows Vista operating system and the Windows XP operating system you can create recovery media using discs only e To create recovery media on the Windows 7 operating system click Start gt All Programs gt Lenovo ThinkVantage Tools gt Factory Recovery Disks Then follow the instructions on the screen Copyright Lenovo 2008 2009 51 e To create Product Recovery discs on the Windows Vista operating system click Start gt All Programs gt ThinkVantage gt Create Product Recovery Media Then follow the instructions on the screen To create Product Recovery discs on the Windows XP operating system click Start gt All Programs gt Think Vantage gt Create Recovery Media Then follow the instructions on the screen Using recovery
29. and solutions for computer problems access the Lenovo troubleshooting center update system drivers and view system information To run the Lenovo System Toolbox program click Start gt All Programs gt Lenovo Services Lenovo System Toolbox Follow the instructions on the screen For additional information about running the diagnostic program refer to the Lenovo System Toolbox help system PC Doctor for Rescue and Recovery The PC Doctor for Rescue and Recovery diagnostic program is part of the Rescue and Recovery workspace on each Lenovo computer Use the PC Doctor for Rescue and Recovery diagnostic program if you are unable to start the Windows operating system To run the PC Doctor for Rescue and Recovery diagnostic program from the Rescue and Recovery workspace do the following 1 Turn off the computer 2 Repeatedly press and release the F11 key when turning on the computer When you hear beeps or see a logo screen stop pressing the F11 key The Rescue and Recovery workspace opens after a short delay 3 From the Rescue and Recovery workspace select Launch advanced Rescue and Recovery gt Diagnose hardware The PC Doctor for Rescue and Recovery diagnostic program opens 4 Select the diagnostic test you want to run Then follow the instructions on the screen For additional information about running the PC Doctor for Rescue and Recovery diagnostic program refer to the PC Doctor for Rescue and Recovery diagnostic
30. ble The following items are not covered by the warranty Replacement or use of parts not manufactured for or by Lenovo or non warranted Lenovo parts Identification of software problem sources Configuration of BIOS as part of an installation or upgrade Changes modifications or upgrades to device drivers Installation and maintenance of network operating systems NOS Installation and maintenance of application programs Chapter 7 Getting information help and service 75 Refer to the safety and warranty information that is provided with your computer for a complete explanation of warranty terms You must retain your proof of purchase to obtain warranty service For a list of service and support phone numbers for your country or region go to http www lenovo com support and click Support phone list or refer to the safety and warranty information provided with your computer Note Phone numbers are subject to change without notice If the number for your country or region is not provided contact your Lenovo reseller or Lenovo marketing representative If possible be at your computer when you call Have the following information available Machine type and model Serial numbers of your hardware products Description of the problem e Exact wording of any error messages e Hardware and software configuration information Using other services If you travel with your computer or relocate it to a count
31. ble to the appropriate connector on the computer 5 Go to Completing the parts replacement Completing the parts replacement After completing all parts replacements you need to reinstall the computer cover and reconnect cables including telephone lines and power cords Depending on the parts replaced you might need to confirm the updated information in the Setup Utility program Refer to Chapter 4 To reinstall the computer cover and reconnect cables to your computer 1 Ensure that all components have been reassembled correctly and no tools or loose screws are left inside your computer See 11 for the location of various components Chapter 2 Installing or replacing hardware 45 2 Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails Then push the computer cover closed until it snaps into position 5 Figure 37 Reinstalling the computer cover 3 If the computer cover is secured with thumbscrews install them 4 If a cover lock is installed lock the cover 5 Reconnect the external cables and power cords to the computer See Locating connectors on the rear of your computer on page 9 6 To update your configuration see Chapter 4 Using the Setup Utility on page Note In most areas of the world Lenovo requires the return of the defective CRU Information about this will come with the CRU or will com
32. bly Note You might have to gently twist the heat sink and fan assembly to free it from the microprocessor 7 Lift the failing heat sink and fan assembly off the system board 26 User Guide 8 Position the new heat sink and fan assembly on the microprocessor socket and then position the clamp on the plastic retention bracket Pivot the handle to clamp the heat sink and fan assembly to the plastic retention bracket m Figure 17 Replacing the heat sink and fan assembly 9 Connect the heat sink and fan assembly cable to the microprocessor fan connector on the system board 10 Go to Completing the parts replacement on page 45 r What to do next e To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on pace 45 Replacing the primary hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety informat
33. circuit board H on the bottom of the hard disk drive Figure 19 Installing the primary hard disk drive into the bracket 10 Slide the new hard disk drive into the drive cage until it snaps into position Chapter 2 Installing or replacing hardware 29 11 Align the drive cage pivot pin with the slot in the upper drive cage and slide the hard disk drive cage into the chassis 12 Connect the signal and power cables to the rear of the new hard disk drive 13 Press down on the metal latch H pivot the drive cage into place and then slide it forward until it snaps into position Note There are two arrows one on the upper drive cage and one on the hard disk drive cage The arrows are aligned when the hard disk drive is in the proper position Figure 20 Installing the primary hard disk drive and bracket 14 Go to Completing the parts replacement on page 45 r What to do next e To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 Replacing the secondary hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support
34. connecting the power switch and LED assembly cable Figure 7 Removing the front bezel 4 To reinstall the front bezel align the plastic tabs on the right side of the front bezel with the corresponding holes in the chassis then pivot the front bezel inward until it snaps into position on the left side To complete the installation go to Completing the parts replacement on page Installing or replacing a PCI card 18 User Guide Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to install or replace a PCI card Your computer has two standard PCI card slots one PCI Express x1 card slot and one PCI Express x16 graphics card slot To install or replace a PCI card do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 3 At the rear of the computer press the release button to open the PCI card latch J and remove the slot cover
35. cue and Recovery main window click the Launch advanced Rescue and Recovery arrow 3 Click the Create Rescue Media icon The Create Rescue and Recovery Media window opens Chapter 3 Recovery information 55 4 In the Rescue Media area select the type of rescue media you want to create You can create a rescue medium using a disc a USB hard disk drive or a secondary internal hard disk drive 5 Click OK and follow the instructions on the screen To create a rescue medium on the Windows Vista operating system or the Windows XP operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Create Recovery Media The Create Rescue and Recovery Media window opens 2 In the Rescue Media area select the type of rescue media you want to create You can create a rescue medium using a disc a USB hard disk drive or a secondary internal hard disk drive 3 Click OK and follow the instructions on the screen Using rescue media This section provides instructions on how to use the rescue media you have created Note Make sure your rescue device optical drive USB device or the secondary internal hard disk drive is set as the first boot device in the startup device sequence before doing this procedure See Selecting a startup device on page 61 To use the rescue medium you have created do one of the following If you have created the rescue medium using a disc
36. dule being replaced as shown Figure 11 Removing the memory module 6 Position the memory module over the memory slot Make sure that the notch on the memory module aligns correctly with the slot key J on the system board Push the memory module straight down into the slot until the retaining clips close Figure 12 Installing the memory module r What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support 22 User Guide This section provides instructions on how to replace the battery Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps this information active when you turn off the computer The battery normally requires no charging or maintenance throughout its life however no battery lasts forever If the battery fails the date time and configuration information including passwords are lost An error me
37. e Setup Utility program 62 User Guide After you finish viewing or changing settings press Esc to return to the Setup Utility program menu you might have to press Esc several times If you want to save the new settings select Save Changes and Exit Otherwise your changes will not be saved Chapter 5 Updating system programs This chapter contains information about updating the POST BIOS and how to recover from a POST BIOS update failure Using system programs System programs are the basic layer of software built into your computer They include the power on self test POST the basic Input Output system BIOS code and the Setup Utility program The POST is a set of tests and procedures that are performed each time you turn on your computer The BIOS is a layer of software that translates instructions from other layers of software into electrical signals that the computer hardware can execute You can use the Setup Utility program to view and change the configuration and setup of your computer Your computer system board has a module called electrically erasable programmable read only memory EEPROM also referred to as flash memory You can easily update the POST the BIOS and the Setup Utility program by starting your computer using a flash update diskette or disc or by running a special update program from your operating system Lenovo might make changes and enhancements to the POST BIOS When updates are released they ar
38. e a few days after the CRU arrives Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www lenovo com support Installation instructions are provided in readme files with the device driver files Installing security features 46 User Guide To help prevent hardware theft and unauthorized access to your computer several security options are available In addition to physical locks unauthorized use of your computer can be prevented by a software lock that locks the keyboard until a correct password is typed in Make sure that any security cables you installed do not interfere with other computer cables Integrated cable lock An integrated cable lock sometimes referred to as the Kensington lock can be used to secure your computer to a desk a table or other non permanent fixture The cable lock attaches to_a security slot at the rear of your computer and is operated with a key See Figure 38 The cable lock also locks the buttons used to open the computer cover This is the same type of lock used with many notebook computers You can order a security cable directly from Lenovo by searching on Kensington at http www lenovo com support Figure 38 Integrated cable lock Chapter 2 Installing or replacing hardware 47 Padlock Your computer is equipped with a padlock loop so that the computer cover cannot be remov
39. e available as downloadable files at http www lenovo com Instructions for using the POST BIOS updates are available in a TXT file that is included with the update files For most models you can download either an update program to create a system program update flash diskette or disc or an update program that can be run from the operating system Note You can download a self starting bootable CD DVD image known as an ISO image of the diagnostics program to support systems without a diskette drive from http www lenovo com Updating flashing the BIOS from a diskette or disc This section provides instructions on how to update flash the BIOS using a diskette or disc System program updates are available at http www lenovo com support 1 To update flash the BIOS From a diskette make sure the computer is turned off and insert a system program update flash diskette Then turn on the computer The update begins From a disc make sure the computer is turned on and insert the disc into the optical drive 2 Turn on the computer If it is on already you must turn it off and back on again The update begins 3 Select a language when prompted by pressing the number on your keyboard that corresponds to the language and then press Enter 4 When prompted to change the serial number press Y 5 Type in the seven character serial number of your computer and then press Enter Copyright Lenovo 2008 2009 63
40. e computer is on e The voltage is set to the correct setting for your country The monitor screen is blank Verify that e The monitor cable is securely attached to the rear of the monitor and to the rear of the computer e The monitor power cord is plugged into the monitor and into a working electrical outlet e The monitor is turned on and the brightness and contrast controls are set correctly e The voltage is set to the correct setting for your country e The monitor signal cable is securely connected to the monitor and to the monitor connector on the computer Note If your computer has two monitor connectors verify that your monitor is connected to the option connector rather than the one in the rear of the system board For more information see Connecting your computer in the ThinkCentre Safety and Warranty Guide The keyboard does not work Verify that The computer does not respond The computer is turned on to the keyboard e The monitor is turned on and the brightness and contrast controls are set correctly The keyboard is securely connected to the keyboard connector on the computer e No keys are stuck Copyright Lenovo 2008 2009 67 Symptom Action The USB Keyboard does not work Verify that e The computer is turned on e The keyboard is securely connected to a USB connector on the front or rear of the computer e No keys are stuck The mouse does not wo
41. e only computer parts provided by Lenovo 2 When installing or replacing an option use the appropriate instructions in this section along with the instructions that come with the option Installing external options External speakers a printer or a scanner can be connected to your computer For some external options you must install additional software in addition to making the physical connection When installing an external option see connectors on the front of your computer on page 8land Locating connectors on the rear of your computer on page 9 to identify the required connector and then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Copyright Lenovo 2008 2009 15 Removing the computer cover 16 User Guide Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to remove the computer cover CAUTION A A Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover To remove the computer cover 1 Remove any media from the drives shut down your o
42. e selected files or restore only the Windows operating system and applications Performing a backup operation This section provides instructions on how to perform a backup operation using the Rescue and Recovery program on different operating systems To perform a backup operation using the Rescue and Recovery program on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens From the Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow Click Back up your hard drive and select backup operation options Follow the instructions on the screen To perform a backup operation using the Rescue and Recovery program on the Windows Vista operating system or the Windows XP operating system do the following 1 3 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Rescue and Recovery The Rescue and Recovery program opens From the Rescue and Recovery main window click Launch advanced Rescue and Recovery Back up your hard drive and select backup operation options Follow the instructions on the screen Performing a recovery operation This section provides instructions on how to perform a recovery operation using the Rescue and Recovery program on different operating systems e To perform a recovery operat
43. ed when a padlock is installed Figure 39 Installing a padlock Password protection To deter unauthorized use of your computer you can use the Setup Utility program to set a password When you turn on your computer you are prompted to type the password to unlock the keyboard for normal use Refer to Using the Setup Utility on page 59 for more information M What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 e 45 Erasing lost or forgotten passwords clearing CMOS This section provides instructions on how to erase lost or forgotten passwords such as a user password To erase a lost or forgotten password do the following 1 Remove the computer cover See Removing the computer cover on page 16 2 Locate the Clear CMOS Recovery jumper on the system board See Locating parts on the system board on page 12 3 Move the jumper from the standard position pin 1 and pin 2 to the maintenance or configure position pin 2 and pin 3 48 User Guide Reinstall the computer cover and connect the power cord See Completing the parts replacement on page 45 Restart the computer leave it on for approximately 10 seconds Turn off the computer by holding the power switch for approximately five seconds Repeat step 1 and step 2 Move the Clear CMOS Recover
44. em from Lenovo The ThinkVantage Productivity Center program contains information sources and tools designed to make computing easy and secure It provides easy access to various technologies such as Rescue and Recovery Client Security Solution Factory Recovery System Update To access the ThinkVantage Productivity Center program click Start gt All Programs gt ThinkVantage Productivity Center Lenovo Welcome The Lenovo Welcome program introduces you to some innovative built in features of Lenovo and guides you through a few important setup tasks to help you make the most of your computer Note The Lenovo Welcome program is only available on computers preinstalled with the Windows 7 operating system from Lenovo Access Help The Access Help information system provides information about getting started doing basic tasks customizing settings for your personal preference protecting data expanding and upgrading and troubleshooting To open the Access Help information system on the Windows 7 operating system click Start gt Help and Support gt Lenovo Access Help To open the Access Help information system on the Windows Vista operating system or the Windows XP operating system click Start gt All Programs gt ThinkVantage gt Access Help After you have opened the Access Help information system use the left panel to make a selection from the Contents tab or the Index tab or use the Search tab t
45. empt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the front audio and USB assembly 40 User Guide To replace the front audio and USB assembly 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 3 Remove the front bezel See Removing and reinstalling the front bezel on page 18 4 Disconnect the front audio and USB assembly cables from the system board See Locating parts on the system board on page 12 5 Note the front audio and USB assembly cables routing and remove the screw that secures the front audio and USB assembly to the chassis 7 S Lye eR SSX Figure 32 Removing the front audio and USB assembly 6 Remove the front audio and USB assembly 7 Route the cables for the new front audio and USB assembly through the hole in the chassis to the system board 8 Install the new front audio and USB assembly into the chassis and secure it with the screw 9 Connect the n
46. er running the diagnostic programs save and print the log files created by the diagnostic programs You will need the log files when you speak to a Lenovo technical support representative Lenovo ThinkVantage Toolbox Note The Lenovo ThinkVantage Toolbox program is only available on computers preinstalled with the Windows 7 operating system from Lenovo The Lenovo ThinkVantage Toolbox program helps you maintain your computer improve computing security diagnose computer problems get familiar with the innovative technologies provided by Lenovo and get more information about your computer You can use the Diagnostics feature of the Lenovo ThinkVantage Toolbox program to test devices diagnose computer problems create bootable diagnostic media update system drivers and view system information 68 User Guide To run the Lenovo ThinkVantage Toolbox program click Start gt All Programs gt Lenovo ThinkVantage Tools gt System Health and Diagnostics Follow the instructions on the screen For additional information about running the Lenovo ThinkVantage Toolbox program refer to the Lenovo ThinkVantage Toolbox help system Lenovo System Toolbox Note The Lenovo System Toolbox program is only available on computers preinstalled with the Windows Vista operating system or the Windows XP operating system from Lenovo The Lenovo System Toolbox diagnostic program works through the Windows operating system to enable you to view symptoms
47. erform the following recovery operations from the Rescue and Recovery workspace Rescue files from your hard disk drive or from a backup The Rescue and Recovery workspace enables you to locate files on your hard disk drive and transfer them to a network drive or other recordable media such as a USB device a disc or a diskette This solution is available even if you did not back up your files or if changes were made to the files since your last backup operation You can also rescue individual files from a Rescue and Recovery backup located on your local hard disk drive a USB device or a network drive Restore your hard disk drive from a Rescue and Recovery backup If you have backed up your hard disk drive using the Rescue and Recovery program you can restore the hard disk drive from a Rescue and Recovery backup even if you cannot start the Windows operating system Restore your hard disk drive to the factory default settings The Rescue and Recovery workspace enables you to restore the complete contents of your hard disk drive to the factory default settings If you have multiple partitions on your hard disk drive you have the option to restore the factory default settings to the C partition and leave the other partitions intact Because the Rescue and Recovery workspace operates independently from the Windows operating system you can restore the factory default settings even if you cannot start the Windows operating system
48. evices such as printers monitors and external drives Unplug all power cords from electrical outlets and remove the computer cover See Removing the computer cover on page 16 3 Access the system board See Removing and reinstalling the front bezel on Locate the Clear CMOS Recovery jumper on the system board See Locating parts on the system board on page 12 Remove any cables that might prevent your access to the Clear CMOS Recovery jumper Move the jumper from the standard position pin 1 and pin 2 to pin 2 and pin 3 Reconnect any cables that were disconnected See Completing the parts replacement on page 45 Reinstall the computer cover and reconnect the power cords for the computer and monitor to electrical outlets Do one of the following Insert the POST BIOS update flash update diskette into the diskette drive and turn on the computer and the monitor Turn on the computer and the monitor and then insert the POST BIOS update flash update disc into the optical drive Turn the computer off and back on again 10 11 12 13 14 15 The recovery session will take two to three minutes During this time you will hear a series of beeps After the update session is completed there will be no video the series of beeps will end and the system will automatically turn off Immediately remove the disc from the optical drive before the computer completely turns off or remove
49. ew front audio and USB assembly cables to the system board See Locating parts on the system board on page 12 10 Reinstall the front bezel 11 Go to Completing the parts replacement on page 45 M What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 Chapter 2 Installing or replacing hardware 41 Replacing the internal speaker 42 User Guide Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the internal speaker To replace the internal speaker 1 w Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Remove the computer cover See Removing the computer cover on page 16 Locate the internal speaker connector on the system board See Locating parts on the system board on page 12 Disconnect the internal speaker cable from the system board Push the metal tab on the top of the internal speaker outward and sl
50. g a recovery repair 56 documentation using 75 drivers device 46 DVI monitor connector 10 Copyright Lenovo 2008 2009 E enabling disabling device 60 environment operating 4 Ethernet 2 Ethernet connector 10 exiting Setup Utility 62 expansion PCI cards 2 external options installing 15 F failure recovering from POST BIOS 64 features 1 flashing the BIOS 63 folder books online 73 front bezel front bezel removing 18 front bezel reinstalling 18 front connectors 8 front fan assembly replacing 37 G getting help 73 information 73 service 73 H hard disk drive replacing 27 heat sink and fan assembly replacing 25 help and service 75 getting 73 important safety information v information getting 73 important safety v resources 73 safety 74 warranty 74 Input Output I O features 2 installing device drivers 57 installing options memory module 21 PCI card 18 security features 46 internal drives 1 internal speaker replacing 42 79 K keyboard connector 10 keyboard replacing 43 L Lenovo System Toolbox 69 Lenovo ThinkVantage Toolbox 68 Lenovo ThinkVantage Tools 73 Lenovo Welcome 5 74 locating components 11 M media creating and using recovery media 51 media creating and using rescue 55 memory module installing replacing 21 system board 21 Microphone connector 10 mouse cleaning 70 non optical 71 optical mouse 70 mouse connector 10 mouse replacing 45 N no
51. ge available at your electrical outlet If necessary use a ballpoint pen to slide the voltage selection switch to a different position If the voltage supply range in your local country or region is 100 127 V AC set the voltage selection switch to 115 V If the voltage supply range in your local country or region is 200 240 V AC set the voltage selection switch to 230 V 7 Install the new power supply assembly into the chassis so that the screw holes in the power supply assembly align with those in the chassis 8 Install the four screws to secure the power supply assembly Note Use only screws provided by Lenovo 9 Reconnect the power supply assembly connectors to the system board 10 Reconnect a power supply assembly connector to each of the drives 11 Go to Completing the parts replacement on page 45 r What to do next e To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 Replacing the heat sink and fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the heat sink and fan
52. gnostics on page 67 For information on additional resources to help you troubleshoot your computer problem see Information resources on page 73 If you suspect a software problem see the documentation including readme files and online help that comes with the operating system or application program Most computers come with a set of diagnostic programs that you can use to help you identify hardware problems For instructions on using the diagnostic programs see Diagnostic programs on page 68 Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download device drivers and updates To access these pages follow the instructions at http www lenovo com support Calling for service During the warranty period you can get help and information by telephone through the Customer Support Center These services are available during the warranty period Problem determination Trained personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the problem Hardware repair If the problem is caused by hardware under warranty trained service personnel are available to provide the applicable level of service Engineering Change management There might be changes that are required after a product has been sold Lenovo or your reseller will make selected Engineering Changes ECs that apply to your hardware availa
53. ia 2 55 Using rescue media i 4 56 Creating and using a recovery repair diskette es a gt 26 Creating a recovery repair diskette 57 Using a recovery repair diskette 57 Installing or reinstalling device drivers 57 Setting a rescue device in the startup sequence 58 Solving recovery problems 58 Chapter 4 Using the Setup Utility 59 Starting the Setup Utility program 59 Viewing and changing settings 59 Using passwords nenn 59 Password considerations 60 User Password 60 Administrator Password z a amp 60 Setting changing and deleting a password 60 Enabling or disabling a device 60 Selecting a startup device e amp 20 ol Selecting a temporary startup device o 61 Selecting or changing the startup device sequence 62 Exiting from the Setup Utility program 62 Chapter 5 Updating system programs 63 Using system programs de 963 Updating flashing the BIOS from a diskette or disc 63 Updating flashing the BIOS from your A system 64 Recovering fiom a POST BIOS update failure 64 Chapter 6 Troubleshooting and diagnostics 67 Basic troubleshooting 67 Diagnostic programs SiMe amp ob amp 468 Lenovo ThinkVantage Toolbox nop m of amp 68 Lenovo System Toolbox aok 69 PC
54. icity although harmless to you can seriously damage computer components and parts When you handle parts and other computer components take these precautions to avoid static electricity damage Limit your movement Movement can cause static electricity to build up around you Always handle parts and other computer components carefully Handle adapter cards memory modules system boards and microprocessors by the edges Never touch any exposed circuitry Prevent others from touching the parts and other computer components Before you replace a new part touch the static protective package containing the part to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body When possible remove the new part from the static protective packaging and install it directly in the computer without setting the part down When this is not possible place the static protective package that the part came in on a smooth level surface and place the part on it Do not place the part on the computer cover or other metal surface Installing or replacing hardware This section provides instructions on how to install or replace hardware for your computer You can expand the capabilities of your computer by adding memory modules PCI cards or drives and maintain your computer by replacing the failing hardware Notes 1 Us
55. ide the internal speaker upward to completely remove it from the chassis Figure 33 Removing the old internal speaker 6 Position a new internal speaker into the metal clips and push downward on the internal speaker until it snaps into position Figure 34 Installing a new internal speaker 7 Connect the speaker cable to the system board See system board on page 12 8 Go to Completing the parts replacement on page 45 r What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 e 45 Replacing the keyboard Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the keyboard To replace the keyboard 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Locate the keyboard connector Chapter 2 Installing or replacing hardware 43 Note Your keyboard might be connected to a
56. ing procedures to select a startup device Selecting a temporary startup device Use this procedure to start up from any startup device Note Not all CDs hard disk drives and diskettes are bootable 1 Turn off your computer 2 Press and hold the F12 key and then turn on the computer When the Startup Device Menu appears release the F12 key Note If you are using a USB keyboard and the Startup Device Menu does not display using this method repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer 3 Select the desired startup device from the Startup Device Menu and press Enter to begin Note Selecting a startup device from the Startup Device menu does not permanently change the startup sequence Chapter 4 Using the Setup Utility 61 Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence do the following 1 Start the Setup Utility program see Starting the Setup Utility program on page 59 2 Select Startup and read the information displayed on the right side of the screen 3 Select the devices for the Primary Boot Sequence the Automatic Boot Sequence and the Error Boot Sequence 4 From the Setup Utility menu select Exit gt Save Changes and Exit If you have changed these settings and want to return to the default settings select Load Optimal Defaults on the Exit menu Exiting from th
57. ion in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the primary hard disk drive To replace the primary hard disk drive 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 Chapter 2 Installing or replacing hardware 27 28 User Guide Locate the primary hard disk drive See Figure 5 on page 13 Disconnect the signal and power cables from the hard disk drive Press the blue release tab down slide the hard disk drive cage H back and pivot it outward Figure 18 Removing the primary hard disk drive 6 Remove the hard disk drive cage from the chassis by simply sliding it outward Pull on the blue handle to release and remove the hard disk drive from the drive cage Remove the hard disk drive from the blue plastic bracket by flexing the sides of the bracket enough to slide it free from the hard disk drive 9 To install a new hard disk drive into the blue bracket flex the bracket and align pin H pin H pin E and pin H on the bracket with the holes in the hard disk drive Do not touch the
58. ion using the Rescue and Recovery program on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens From the Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow Click the Restore your system from a backup icon Chapter 3 Recovery information 53 4 Follow the instructions on the screen e To perform a recovery operation using the Rescue and Recovery program on the Windows Vista operating system or the Windows XP operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Rescue and Recovery The Rescue and Recovery program opens 2 From the Rescue and Recovery main window click Launch advanced Rescue and Recovery 3 Click the Restore your system from a backup icon 4 Follow the instructions on the screen For more information about performing a recovery operation from the Rescue and Recovery workspace see Using the Rescue and Recovery workspace Using the Rescue and Recovery workspace 54 User Guide The Rescue and Recovery workspace resides in a protected hidden area of your hard disk drive that operates independently from the Windows operating system This enables you to perform recovery operations even if the Windows operating system cannot be started You can p
59. itch setting 115 V ac High range Minimum 200 V ac Maximum 240 V ac Input frequency range 50 60 Hz Voltage selection switch setting 230 V ac 4 User Guide Software overview The computer comes with a preinstalled operating system and several preinstalled applications Software provided with your Windows operating system This section describes the Windows applications provided with your computer Software provided by Lenovo The following software applications are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer Software provided with your computer may vary depending on your model type Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely For more information see Lenovo ThinkVantage Tools on page 73 Note The Lenovo ThinkVantage Tools program is only available on computers with the Windows 7 operating system from Lenovo ThinkVantage Productivity Center The ThinkVantage Productivity Center program guides you to a host of information and tools to help you set up understand maintain and enhance your computer Note The ThinkVantage Productivity Center program is only available on computers preinstalled with the Windows Vista operating system or the Windows XP operating system from Lenovo Lenovo We
60. l hard disk drive Optical drive some models Video subsystem Integrated graphics controller for a VGA Video Graphics Array connector and a Digital Visual Interface DVI connector dual display supported e PCI Express x16 graphics card slot on the system board Audio subsystem e High Definition HD with Realtek ALC662 Microphone connector and headphone connector on the front panel Copyright Lenovo 2008 2009 1 2 User Guide Audio line in connector audio line out connector and microphone connector on the rear panel Mono internal speaker Connectivity 10 100 1000 Mbps integrated Ethernet controller Peripheral Component Interconnect PCI V 90 Data Fax modem some models System management features e Ability to store power on self test POST hardware test results ASF 2 0 Alert Standard Format Specification Automatic power on startup e Preboot Execution Environment PXE and Dynamic Host Configuration Protocol DHCP e Remote Administration System Management SM BIOS and SM software e Wake on LAN Wake on Ring in the Setup Utility program this feature is called Serial Port Ring Detect for an external modem Input Output I O features e 25 pin Extended Capabilities Port ECP Extended Parallel Port EPP 9 pin serial port some models e DVI monitor connector e Eight USB Universal Serial Bus connectors two on the front panel and six on the rear panel e Etherne
61. lcome The Lenovo Welcome program introduces you to some innovative built in features of Lenovo and guides you through a few important setup tasks to help you make the most of your computer Note The Lenovo Welcome program is only available on computers preinstalled with the Windows 7 operating system from Lenovo ThinkVantage Rescue and Recovery The ThinkVantage Rescue and Recovery RnR program is a one button recovery and restore solution that includes a set of self recovery tools to help you diagnose computer problems get help and recover from system crashes quickly even if the primary operating system could not start ThinkVantage Client Security Solution The ThinkVantage Client Security Solution program is available on select Lenovo computers It helps protect your information including vital security information like passwords encryption keys and electronic credentials while guarding against unauthorized user access to data Note The ThinkVantage Client Security Solution program is only available on computers preinstalled with the Windows Vista operating system or the Windows XP operating system from Lenovo Password Manager The Password Manager program helps you automatically capture and fill in authentication information for Windows applications and Web sites Note The Password Manager program is only available on computers preinstalled with the Windows 7 operating system from Lenovo Chapter 1 Product overview 5
62. ldup usually appears as a stripe running across the middle of the rollers If the rollers are dirty clean them by using a cotton swab soaked in isopropyl rubbing alcohol Turn the rollers with your finger and continue swabbing them until all the dirt is removed Be sure the rollers are still centered in their channels after you clean them Remove any fibers from the swab that might be remaining on the rollers Replace the ball and the retainer ring Twist the retainer ring to the locked position Reconnect the mouse cable to the computer Turn your computer back on Chapter 7 Getting information help and service This chapter contains information about help service and technical assistance for products manufactured by Lenovo Information resources This section describes how to access useful resources relating to your computing needs Online Books folder Note The Online Books folder is only available on computers that have an internal hard disk drive and preinstalled software from Lenovo The Online Books folder preinstalled on your computer contains the ThinkCentre User Guide which provides information about your computer to help you set up use and maintain your computer It requires no Internet access to view the publication To view the publications click Start gt All Programs gt Online Books gt Online Books then double click the appropriate publication for your computer The publications are also av
63. lenovo ThinkCentre User Guide o Thinktentre Machine Types 3656 7061 7090 9353 9421 9485 9623 9625 9705 9795 9935 9946 and 9953 lenovo ThinkCentre User Guide Note Before using this information and the product it supports be sure to read and understand the ThinkCentre Safety and Warranty Guide and Notices on page 77 Second Edition December 2009 Copyright Lenovo 2008 2009 LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 Contents Important safety information Chapter 1 Product overview Features Specifications Software overview Software provided with your Windows operating system Antivirus sativa Locations G gis nad lt CON Ol Locating connectors on the front of your computer 8 Locating connectors on the rear of your computer 11 12 12 Locating components Locating parts on the system hoard Locating internal drives Chapter 2 Installing or replacing hardware
64. ligning the new rubber mounts of the new front fan assembly with the holes on the chassis and push the rubber mounts through the holes Note The new front fan assembly you received will have four new rubber mounts attached Chapter 2 Installing or replacing hardware 37 7 Pull on the tips of the rubber mounts until the fan assembly is in place Figure 29 Installing the front fan assembly 8 Connect the front fan assembly cable to the power fan connector on the system board 9 Go to Completing the parts replacement on page 45 M What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on age 45 Replacing the rear fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the rear fan assembly 38 User Guide To replace the rear fan assembly 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Remove the
65. make sure that your computer is turned on and insert the rescue disc Then restart the computer The rescue medium starts If you have created the rescue medium using a USB hard disk drive attach the USB hard disk drive to one of the USB connectors on your computer Then turn on the computer The rescue medium starts If you have created the rescue medium using a secondary internal hard disk drive set the secondary internal hard disk drive as the first boot device in the startup device sequence Then the rescue medium starts When the rescue medium starts the Rescue and Recovery workspace opens The help information for each feature is available from the Rescue and Recovery workspace Follow the instructions to complete the recovery process Creating and using a recovery repair diskette 56 User Guide If you are unable to access the Rescue and Recovery workspace or the Windows environment use a recovery repair diskette to repair the Rescue and Recovery workspace or repair a file needed to enter the Windows environment It is important to create a recovery repair diskette as early as possible and store it in a safe place as a precautionary measure Note You need to have a diskette drive for creating and using a recovery repair diskette If you do not have an internal diskette drive you can use an external USB diskette drive Creating a recovery repair diskette This section provides instructions on how to create a recove
66. media 52 User Guide This section provides instructions on how to use recovery media on different operating systems To use recovery media on the Windows 7 operating system or the Windows Vista operating system do the following Attention When you use recovery media to restore the computer to the factory default settings on the Windows 7 operating system or the Windows Vista operating system all the files currently on the system drive or the hard disk drive will be deleted and replaced by the factory default settings 1 Depending on the type of your recovery media connect your boot medium memory key or USB hard disk drive to your computer or insert the boot disc into your CD or DVD drive 2 Restart your computer 3 Repeatedly press and release the F12 key when turning on the computer When the Please select boot device window opens release the F12 key 4 Depending on the type of your recovery media select the proper startup device and press Enter After a short delay the Product Recovery program opens 5 Follow the instructions on the screen After restoring the computer to the factory default settings you might have to reinstall some software programs or device drivers See reinstalling device drivers on page 57 for details To use Product Recovery discs on the Windows XP operating system do the following Attention When you use Product Recovery discs to restore the computer to the factory default set
67. n optical mouse 71 notice television output 78 notices 77 O online books folder 73 operations backup and recovery 53 optical drive replacing 33 optical mouse 70 P padlock 48 parallel port 10 parts replacement completing 45 password administrator 60 considerations 60 setting changing deleting 60 user 60 password protection 48 passwords erasing 48 lost or forgotten 48 passwords using 59 PC Doctor for Rescue and Recovery 69 PCI card 18 installing replacing 18 slots 18 PCI card latch 19 physical specifications 4 power Advanced Configuration and Power Interface ACPI support 2 80 User Guide power continued features 2 power supply assembly replacing 24 power on self test POST 63 Productivity Center ThinkVantage 74 programs updating system 63 protection password 48 purchasing additional services 76 R rear connectors 9 rear fan assembly replacing 38 recovering from a POST BIOS update failure 64 software 51 recovery Boot block 64 operations backup and 53 problems solving 58 recovery repair diskette creating and using 56 recovery media creating and using 51 reinstalling device drivers 57 removing cover 16 replacing battery 23 hard disk drive 27 heat sink and fan assembly 25 Rescue and Recovery 51 workspace Rescue and Recovery 54 Rescue and Recovery workspace 54 rescue device startup sequence 58 rescue media creating and using 55 resources information 73 S safety
68. nderstanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the power supply assembly To replace the power supply assembly 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Remove the computer cover See Removing the computer cover on page 16 Disconnect the power supply assembly cables from the system board and all drives See Locating parts on the system board on page 12 Lay the computer on its side and remove the four screws at the rear of the chassis that secure the power supply assembly Figure 15 Removing the retaining screws for the power supply assembly 5 Remove the power supply assembly from the chassis 6 Ensure that the power supply assembly is the correct replacement Some 24 User Guide power supply assemblies automatically sense the voltage some power supply assemblies are voltage specific and some power supply assemblies have a voltage selection switch If your computer has a voltage selection switch ensure that you set the voltage selection switch of the new power supply assembly to match the volta
69. ng or reinstalling device drivers Before installing or reinstalling device drivers make sure that you have a preinstalled operating system and the documentation and software media for the device Device drivers for factory installed devices are located in the SWTOOLS DRIVERS subdirectory on the computer hard disk drive usually drive C The latest device drivers for factory installed devices are also available at http www lenovo com Other device drivers are on the software media that come with individual devices To install or reinstall a device driver for a factory installed device do the following 1 Turn on the computer 2 Use Windows Explorer or My Computer to display the directory structure of your hard disk drive 3 Go to the C SWTOOLS directory Chapter 3 Recovery information 57 4 Open the DRIVERS folder Within the DRIVERS folder there are several subfolders named for various devices installed in your computer such as AUDIO or VIDEO Open the appropriate device subfolder O 0 Do one of the following e In the device subfolder look for a README txt file or a file with the txt extension This file might be named after the operating system such as WIN98 txt The TXT file contains information about how to install the device driver Follow the instructions to complete the installation If the device subfolder contains a file with the inf extension and you want to install the device driver
70. o Support Web site at http www lenovo com support Copyright Lenovo 2008 2009 v Vi User Guide Chapter 1 Product overview This chapter provides an introduction to the features and options that are available for your computer You can expand the capabilities of your computer by adding memory modules drives or PCI cards When installing or replacing an option use these instructions along with the instructions that come with the option Important Before you install or replace any option be sure to read and understand the Important safety information first These precautions and guidelines will help you work safely Note Use only computer parts provided by Lenovo Features This section provides an overview of the computer features and preinstalled software m System information The following information covers a variety of models For information about our specific model use the Setup Utility See Chapter 4 Using the Setup Utility on page 59 Microprocessor e AMD Athlon microprocessor e AMD Phenom microprocessor e AMD Sempron microprocessor Internal cache size varies by model type Memory Supports up to four DDR2 DIMMs double data rate 2 dual inline memory modules Flash memory for system programs varies by model type Internal drives Diskette drive or card reader varies by model type Serial Advanced Technology Attachment SATA interna
71. o find a particular word or phrase Safety and Warranty The safety and warranty information that is provided with your computer contains information on safety warranty and notices Be sure to read and understand all the safety information before using this product Lenovo Web site http www lenovo com The Lenovo Web site provides up to date information and services to help you buy upgrade and maintain your computer You can also do the following Shop for desktop and notebook computers monitors projectors upgrades and accessories for your computer and special offers Purchase additional services such as support for hardware operating systems application programs network setup and configuration and custom installations 74 User Guide Purchase upgrades and extended hardware repair services Download the latest device drivers and software updates for your computer model e Access the online manuals for your products Access the Lenovo Limited Warranty Access troubleshooting and support information for your computer model and other supported products Find the service and support phone number for your country or region Find a Service Provider located near you Help and service This section contains information about obtaining help and service Using the documentation and diagnostic programs If you experience a problem with your computer see Chapter 6 Troubleshooting and dia
72. on in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to install or replace a memory module Your computer has four slots for installing or replacing DDR2 DIMMs double data rate 2 dual inline memory modules that provide up to a maximum of 8 GB of system memory When installing or replacing memory modules use the following guidelines Use 1 8 V 240 pin DDR2 SDRAM double data rate 2 synchronous dynamic random access memory Use 512 MB 1 GB or 2 GB memory modules in any combination up to a maximum of 8 GB Note Only DDR2 SDRAM DIMMs can be used To install or replace a memory module 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Remove the computer cover See Removing the computer cover on page 16 Remove any parts that might prevent access to the memory slots Locate the memory slots See Locating parts on the system board on page 12 Open the retaining clips oP ON Figure 10 Opening the retaining clips Chapter 2 Installing or replacing hardware 21 If you are replacing an old memory module open the retaining clips and remove the memory mo
73. on go to the appropriate section e To complete the installation go to Completing the parts replacement on ee 45 36 User Guide Replacing the front fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the front fan assembly To replace the front fan assembly 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 3 Remove the front bezel See Removing and reinstalling the front bezel on 4 Disconnect the front fan assembly cable from the power fan connector on the system board See Locating parts on the system board on page 12 5 The front fan assembly is attached to the chassis by four rubber mounts Remove the front fan assembly by breaking or cutting the rubber mounts and gently pulling the front fan assembly out of the chassis Figure 28 Removing the front fan assembly 6 Install the new front fan assembly by a
74. ose computer problems get familiar with the innovative technologies provided by Lenovo and get more information about your computer See Lenovo Think Vantage Toolbox on page 68 for detailed information Note The Lenovo ThinkVantage Toolbox program is only available on computers preinstalled with the Windows 7 operating system from Lenovo Lenovo System Toolbox The Lenovo System Toolbox program is preinstalled on your computer This diagnostic program works through the Windows operating system to diagnose hardware problems and report operating system controlled settings that can cause hardware failures See Lenovo System Toolbox on page 69 for more information Note The Lenovo System Toolbox program is only available on computers preinstalled with the Windows Vista operating system or the Windows XP operating system from Lenovo PC Doctor for Rescue and Recovery The PC Doctor for Rescue and Recovery diagnostic program is preinstalled on your ThinkCentre computer as part of the Rescue and Recovery workspace It helps you diagnose hardware problems and report operating system controlled settings that can cause hardware failures Use the PC Doctor for Rescue and Recovery program if you_are unable to start the Windows operating system For more information see PC Doctor for Rescue and Recovery on page 69 Adobe Reader The Adobe Reader program is a tool used to view print and search PDF documents See Online Book
75. ostic program from a diagnostic disc that you created To run the diagnostic program from a diagnostic disc that you created do the following 1 Make sure the optical drive you want to use is set as the first boot device in the startup device sequence See Selecting a startup device on page 61 2 Make sure the computer is turned on and then insert the disc into the optical drive The diagnostic program opens Note You can insert the disc into the optical drive when you are setting the startup device sequence However if you insert the disc into the optical drive when you have already entered the operating system you need to restart the computer to access the diagnostic program 3 Follow the instructions on the screen to select the diagnostic test you want to run Note For additional help press the F1 key 4 Remove the diagnostic disc from the optical drive when you complete the diagnostic process Cleaning the mouse This section provides instructions on how to clean an optical or non optical mouse Optical mouse 70 User Guide An optical mouse uses a light emitting diode LED and an optical sensor to navigate the pointer If the pointer on the screen does not move smoothly with the optical mouse you might need to clean the mouse To clean the optical mouse 1 Turn off your computer 2 Disconnect the mouse cable from the computer 5 6 Turn the mouse upside down to look at the lens a If
76. passwords The Setup Utility program might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer Viewing and changing settings The Setup Utility program menu lists items that identify system configuration topics To view or change settings see Starting the Setup Utility program When working with the Setup Utility program menu you must use the keyboard The keys used to perform various tasks are displayed at the bottom of each screen Using passwords By using the Setup Utility program you can set passwords to prevent unauthorized access to your computer and data See Starting the Setup Utilit program The following types of passwords are available e User Password e Administrator Password You do not have to set any passwords to use your computer However if you decide to set any passwords read the following sections Copyright Lenovo 2008 2009 59 Password considerations A password can be any combination of up to 12 1 to 12 alphabetic and numeric characters a z and 0 9 For security reasons it is recommended to use a strong password that cannot be easily compromised A strong password should adhere to the following rules Have at least eight characters in length and contain at least one alphabetic character and one numeric character Setup Utility program and hard disk drive passwords are not case sensitive Not be your name
77. perating system and turn off all attached devices and the computer 2 Unplug all power cords from electrical outlets 3 Disconnect the cables attached to the computer This includes power cords Input Output I O cables and any other cables that are connected to the computer See Locating connectors on the front of your computer on page 8 and Locating connectors on the rear of your computer on page 9 4 Remove any locking devices such as a cable lock that secures the computer cover 5 If there are thumbscrews that secure the computer cover remove them 6 Press the cover release button on the side of the computer cover and slide the computer cover to the rear to remove Figure 6 Removing the computer cover Chapter 2 Installing or replacing hardware 17 Removing and reinstalling the front bezel This section provides instructions on how to remove and reinstall the front bezel To remove and reinstall the front bezel 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Remove the computer cover See Removing the computer cover on page 16 Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the front bezel outward Carefully set the front bezel to the side without dis
78. rd disk drive to the factory default settings you might have to reinstall device drivers for some devices See Installing or reinstalling Some computers come with Microsoft Office or Microsoft Works preinstalled If you need to recover or reinstall your Microsoft Office or Microsoft Works applications you must use the Microsoft Office CD or Microsoft Works CD These CDs are provided only with computers preinstalled with Microsoft Office or Microsoft Works Creating and using rescue media With rescue media such as a disc or a USB hard disk drive you can recover the computer from failures that prevent you from gaining access to the Rescue and Recovery workspace on your hard disk drive Notes 1 The recovery operations you can perform using rescue media vary depending on the operating system The rescue discs can be started in any type of CD or DVD drive You can also run the PC Doctor for Rescue and Recovery diagnostic program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace Creating rescue media This section provides instructions on how to create rescue media on different operating systems To create a rescue medium on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens 2 From the Res
79. rk The computer does not respond to the mouse Verify that The computer is turned on The mouse is securely connected to the mouse connector on the computer The mouse is clean Refer to Cleaning the mouse on page 70 for further information The operating system will not start Verify that e There is no diskette in the diskette drive e The startup sequence includes the device where the operating system resides ing system is on the hard disk drive For more information The computer beeps multiple times before the operating system starts Verify that no keys are stuck down Diagnostic programs Diagnostic programs are used to test hardware components of your computer Diagnostic programs are also used to report operating system controlled settings that interfere with the correct operation of your computer There are two programs preinstalled on your computer to help you diagnose computer problems Lenovo ThinkVantage Toolbox or Lenovo System Toolbox depending on your operating system used when you are running the Windows operating system PC Doctor for Rescue and Recovery used when your Windows operating system does not start Notes 1 You can also download the PC Doctor for DOS diagnostic program from http www lenovo com support See PC Doctor for DOS on page 70 for detailed information If you are unable to isolate and repair the problem yourself aft
80. ry repair diskette To create a recovery repair diskette do the following 1 Turn on the computer and make sure that your computer has Internet access 2 Follow the instructions on the Web site at 3 After the recovery repair diskette is created take out the diskette from the diskette drive and label it Recovery Repair Diskette Then store it in a safe place for future use Using a recovery repair diskette This section provides instructions on how to use a recovery repair diskette To use the recovery repair diskette you created do the following 1 Turn off the computer 2 Insert the recovery repair diskette into the diskette drive 3 Turn on the computer and follow the instructions on the screen Notes 1 If the repair operation completes without any error you will be able to access the Rescue and Recovery workspace by repeatedly pressing the F11 key while you restart your computer When you hear beeps or see a logo screen release the F11 key You will also be able to access the Windows environment after the repair operation completes 2 If an error message appears during the repair operation and the repair operation cannot be completed you might have a problem with the partition that contains the Rescue and Recovery workspace Use a rescue medium to access the Rescue and Recovery workspace For information about creating and using rescue media see Creating and using rescue media on page 55 Installi
81. ry where your desktop or notebook computer machine type is sold your computer might be eligible for International Warranty Service which automatically entitles you to obtain warranty service throughout the warranty period Service will be performed by service providers authorized to perform warranty service Service methods and procedures vary by country and some services might not be available in all countries International Warranty Service is delivered through the method of service such as depot carry in or on site service that is provided in the servicing country Service centers in certain countries might not be able to service all models of a particular machine type In some countries fees and restrictions might apply at the time of service To determine whether your computer is eligible for International Warranty Service and to view a list of the countries where service is available go to http www lenovo com support click Warranty and follow the instructions on the screen For technical assistance with the installation of or questions related to Service Packs for your preinstalled Microsoft Windows product refer to the Microsoft Product Support Services Web site at http support microsoft com directory or you can contact the Customer Support Center Some fees might apply Purchasing additional services 76 User Guide During and after the warranty period you can purchase additional services such as support for hardware
82. s an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may Copyright Lenovo 2008 2009 77 vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment Television output notice The following notice applies to models that have the factory installed television output feature This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited Trademarks 78 User Guide The following terms are trademarks of Lenovo in the United States other countries or both Leno
83. s folder on page 73 for more information about accessing the online books and the Lenovo Web site Antivirus software Your computer comes with antivirus software that you can use to detect and eliminate viruses Lenovo provides a full version of antivirus software on your computer with a free 30 day subscription After 30 days you must renew the license to continue receiving the antivirus software updates For more information about how to use your antivirus software refer to the help system of your antivirus software Chapter 1 Product overview 7 Locations This section provides information to help you locate your computer connectors components parts on the system board and internal drives Locating connectors on the front of your computer Figure 1 shows the location of the connectors on the front of your computer Figure 1 Front connector locations USB connector Microphone connector H Headphone connector EJ USB connector 8 User Guide Locating connectors on the rear of your computer shows the location of the connectors on the rear of your computer Some connectors on the rear of your computer are color coded to help you determine where to connect the cables on your computer AAN Pea rt
84. ssage is displayed when you turn on the computer Refer to the Lithium battery notice in the ThinkCentre Safety and Warranty Guide for information about replacing and disposing of the battery To replace the battery 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 16 3 Locate the battery See Locating parts on the system board on page 12 4 Remove the old battery Figure 13 Removing the old battery 5 Install a new battery Figure 14 Installing a new battery 6 Reinstall the computer cover and connect the cables See Completing the parts replacement on page 45 Note When the computer is turned on for the first time after replacing the battery an error message might be displayed This is normal after replacing the battery 7 Turn on the computer and all attached devices Chapter 2 Installing or replacing hardware 23 What to do next To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 45 Replacing the power supply assembly Attention Do not open your computer or attempt any repair before reading and u
85. t connector One external Serial Advanced Technology Attachment eSATA connector through PCI bracket some models e PS 2 keyboard connector e PS 2 mouse connector Three audio connectors audio line in connector audio line out connector and microphone connector on the rear panel Two audio connectors microphone connector and headphone connector on the front panel e VGA monitor connector Expansion Three drive bays Two 32 bit PCI card slots One PCI Express x1 card slot One PCI Express x16 graphics card slot Power e 280 watt auto sensing power supply some models Automatic 50 60 Hz input frequency switching Advanced Configuration and Power Interface ACPI support Security features Cover presence switch also called intrusion switch some models Diskette and hard disk drive I O control Keyboard with fingerprint reader some models Startup sequence control Startup without diskette drive keyboard or mouse Serial port and parallel port I O control Support for the addition of an integrated cable lock Kensington lock User and administrator passwords for BIOS access Unattended start mode Preinstalled software Your computer might come with preinstalled software If it does an operating system device drivers to support built in features and other support programs are included Operating system preinstalled e Microsoft Windows 7 e Microsoft
86. the diskette from the diskette drive Repeat steps 2 through 5 Move the jumper back to the standard position pin 1 and pin 2 Reconnect any cables that were disconnected See Completing the parts replacement on page 45 Reinstall the computer cover and reconnect the power cords for the computer and monitor to electrical outlets Turn on the computer to restart the operating system Chapter 5 Updating system programs 65 66 User Guide Chapter 6 Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs If your computer problem is not described here see Chapter 7 Getting information help for additional troubleshooting resources Basic troubleshooting The following table provides information to help you troubleshoot your computer problems Note If you cannot correct the problem have the computer serviced For a list of service and support telephone numbers refer to the ThinkCentre Safety and Warranty Guide that comes with your computer or go to the Lenovo Support Web site at http www lenovo com support phone Symptom Action The computer does not start Verify that when you press the power The power cord is plugged into the rear of the computer and into a working button electrical outlet If your computer has a secondary power switch on the back of the computer make sure that it is switched on The power indicator on the front of th
87. tings on the Windows XP operating system all the files currently on the hard disk drive will be deleted and replaced by the factory default settings During the restore process you will be given the option to save one or more files currently on the hard disk drive to other media before the data is deleted 1 Insert the boot disc into your CD or DVD drive 2 Restart your computer 3 Repeatedly press and release the F12 key when turning on the computer When the Please select boot device window opens release the F12 key 4 Select the CD or DVD drive as the startup device and press Enter After a short delay the Rescue and Recovery workspace opens 5 From the Rescue and Recovery menu click Restore your system 6 Follow the instructions on the screen Performing backup and recovery operations The Rescue and Recovery program enables you to back up all your hard disk drive contents including the operating system data files software programs and personal settings You can designate where the Rescue and Recovery program stores the backup On a protected area of your hard disk drive On a secondary hard disk drive installed in your computer On an attached external USB hard disk drive On a network drive On recordable CDs or DVDs a recordable CD or DVD drive is required for this option After you have backed up the contents on the hard disk drive you can restore the complete contents of the hard disk drive restore only th
88. using the INF file click Start gt Help and Support to enter the Windows Help and Support information system for the detailed information about how to install the device driver e In the device subfolder look for a SETUP EXE file Double click the file and follow the instructions on the screen Setting a rescue device in the startup sequence Before you start the Rescue and Recovery program from an internal hard disk drive a disc a USB hard disk drive or other external devices you must first make sure that your rescue device is set as the first boot device in the startup device sequence in the Setup Utility program Refer tol Selecting ar device orl age 6ilfor detailed information about temporarily or permanently changing the startup sequence Note If you use an external device you must first turn off your computer before connecting the external device For more information on the Setup Utility program see Chapter 4 Using the Setup Utility on page 59 Solving recovery problems 58 User Guide If you are unable to access the Rescue and Recovery workspace or the Windows environment do one of the following Use a rescue medium to start the Rescue and Recovery workspace See and using rescue media on page 55 Use a recovery repair diskette to repair the Rescue and Recovery workspace or repair a file needed to enter the Windows environment See Creating and using n a recovery repair diskette
89. vo The Lenovo logo PS 2 Rescue and Recovery ThinkCentre ThinkVantage Microsoft Windows and Windows Vista are trademarks of the Microsoft group of companies AMD AMD Athlon AMD Phenom AMD Sempron and combinations thereof are trademarks of Advanced Micro Devices Inc Linux is a trademark of Linus Torvalds in the United States other countries or both Other company product or service names may be trademarks or service marks of others Index A administrator password 60 antivirus software 7 audio line in connector 10 audio line out connector 10 audio subsystem 1 backup and recovery operations 53 basic troubleshooting 67 battery replacing 23 BIOS updating flashing 63 64 Boot block recovery 64 C cable lock security 47 changing password 60 startup device sequence 62 cleaning the mouse 70 CMOS clearing 48 components internal 11 computer cover reinstalling 45 connector description 10 connectors front 8 rear 9 considerations password 60 cover removing 16 creating and using a recovery repair diskette 56 and using rescue media 55 creating and using recovery media 51 CRU completing the installation 45 customer support center 75 D deleting password 60 device drivers 46 installing 57 reinstalling 57 devices handling static sensitive 15 diagnostics programs using 75 diagnostics troubleshooting 67 diskette drive or card reader replacing 35 diskette creating and usin
90. w hard disk drive into the hard disk drive cage until it snaps into position 11 Install the hard disk drive cage into the chassis until it snaps into position underneath the metal tab Make sure that the hard disk drive cage is secured in the chassis Figure 23 Installing the secondary hard disk drive and drive cage 12 Connect the signal and power cables to the rear of the new hard disk drive 13 Go to Completing the parts replacement on page 45 What to do next e To work with another option go to the appropriate section e To complete the installation go to Completing the parts replacement on page 45 45 Replacing the optical drive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the optical drive To replace the optical drive Chapter 2 Installing or replacing hardware 33 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover
91. y jumper back to the standard position pin 1 and pin 2 Reinstall the computer cover and connect the power cord See Completing the parts replacement on page 45 Chapter 2 Installing or replacing hardware 49 50 User Guide Chapter 3 Recovery information This chapter will help you get familiar with recovery solutions provided by Lenovo This chapter explains when and how to use the following recovery methods Creating and using recovery media Performing backup and recovery operations Using the Rescue and Recovery workspace Creating and using rescue media Creating and using a recovery repair diskette Installing or reinstalling device drivers Setting a rescue device in the startup sequence Solving recovery problems Notes 1 There are a variety of methods to choose from when considering how to recover in the event of a software or hardware related problem Some methods vary depending on the type of your operating system 2 The product on the recovery media may be used only for the following purposes Restore the product preinstalled on your computer Reinstall the product Modify the product using the Additional Files Creating and using recovery media Recovery media enable you to restore the hard disk drive to the factory default settings Recovery media are useful if you transfer the computer to another area sell the computer recycle the computer or put the computer in

Lenovo 3656 Personal Computer User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents