Home

Lanzar Car Audio 1801D Car Amplifier User Manual

1. Hazardous voltage current and energy levels are present inside any component that has this label attached There are no serviceable parts inside these components If you suspect a problem with one of these parts contact a service technician To replace the power supply do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Disconnect the power supply cable from the system board See System board part and connector locations on page 12 5 Remove the hard disk drive See Replacing the hard disk drive on page 25 6 Remove the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 Chapter 2 Installing or replacing hardware 47 7 11 12 13 14 15 Remove the four screws that secure the power supply and then remove the two screws H that secure the power cord connector bracket Note the routing of the power cord connector cable E Lift the power supply up to remove it from the computer main bracket Figure 37
2. Figure 1 Front control and part locations Integrated camera with microphone MIC EJ Wireless activity indicator available in some models El Integrated camera on off button EJ Menu Enter Eff Liquid crystal display LCD panel Brightness control Right EJ Power switch Image setup control Left H Power indicator Monitor mode control Exit Wi Hard disk drive activity indictor Microphone mute on control Bluetooth activity indicator Using your computer in monitor mode Your computer can work in two modes computer mode or monitor mode This section provides instructions on how to use your computer in monitor mode 8 ThinkCentre User Guide To use your computer in monitor mode you need to have a second computer Connect one end of the VGA cable to the VGA IN connector on the rear of your computer and the other end to the VGA connector on the second computer Use the monitor mode control 232 on the front of your computer to switch your computer between computer mode and monitor mode The following table shows the functions of each control when your computer works in computer mode or monitor mode ee a Menu Open the main On Screen Display OSD menu Confirm a selection aca control Adjust overall monitor brightness Rear view Figure 2 Rear connector locations on page 9 shows the locations of the connectors on the rear of your computer Some connectors on the rear of your computer are color coded to help you deter
3. Removing or reinstalling the lift stand on page 17 To remove or reinstall the frame stand do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 16 ThinkCentre User Guide 3 Remove the four screws that secure the frame stand Keep the four screws and put them aside You will need them when installing the frame stand Figure 6 Removing the frame stand 4 Lift the frame stand off the computer and put it in a safe place 5 To reinstall the frame stand position the frame stand so that the four screw holes align with those in the computer VESA frame and then install the four screws to secure the frame stand What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Removing or reinstalling the lift stand Your computer might come with a lift stand or a frame stand This section provides instructions on how to remove or reinstall the lift stand For information about the frame stand see Removing or reinstalling the frame stand on pag
4. on page 51 Replacing the mouse Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the mouse Replacing the PS 2 or USB mouse To replace the PS 2 or USB mouse do the following 1 Remove any media from the drives Then turn off all attached devices and the computer 50 ThinkCentre User Guide 2 Disconnect all power cords from electrical outlets 3 Locate the mouse connector Note Your mouse might be connected to a PS 2 mouse connector J or a USB connector EI A Figure 39 Mouse connectors 4 Disconnect the failing mouse cable from the computer 5 Connect a new mouse cable to the appropriate connector on the computer 6 Reconnect all power cords to electrical outlets Replacing the wireless mouse To replace the wireless mouse do the following 1 Disconnect the USB dongle from your computer Then take away your failing wireless mouse 2 Remove the new wireless mouse from the package 3 Remove the USB dongle from the compartment of the new wireless mouse and correctly install the batteries for the mouse Then connect the USB dongle to an available USB connector on your computer
5. Component locations on page 11 Disconnect the right I O assembly cable and the intrusion switch cable from the right I O assembly oak Ww Remove the three screws J that secure the right I O assembly and then remove the right I O assembly from the computer Figure 36 Removing the right I O assembly 46 ThinkCentre User Guide 7 To install the new right I O assembly into the computer position the new right I O assembly into place and then align the screw holes with the corresponding holes in the computer main bracket 8 Install the three screws to secure the right I O assembly to the computer main bracket 9 Connect the right I O assembly cable and the intrusion switch cable to the new right I O assembly What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the power supply Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the power supply CAUTION Never remove the cover on a power supply or any part that has the following label attached
6. Follow the instructions on the screen to set change or delete a password Note A password can be any combination of up to 64 1 to 64 alphabetic and numeric characters For more information see Password considerations on page 64 64 ThinkCentre User Guide Enabling or disabling a device This section provides instructions on how to enable or disable user access to a device USB Support Use this option to enable or disable a USB connector When a USB connector is disabled the device connected to the USB connector cannot be used SATA Controller When this option is set to Disabled the device connected to the SATA connector such as the hard disk drive or the optical drive is disabled and cannot be accessed To enable or disable a device do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 63 2 Depending on the device you want to enable or disable do one of the following e From the Setup Utility program main menu select Devices gt USB Setup and follow the instructions on the screen to enable or disable the USB connector s of your choice e From the Setup Utility program main menu select Devices gt ATA Drive Setup gt SATA Controller to enable or disable the device connected to the corresponding SATA connector on the system board 3 Select the desired settings and press Enter 4 Press Esc to return to the Setup Utility program main menu You might have to pres
7. Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 15 3 Locate the Clear CMOS Recovery jumper on the system board See System board part and connector locations on page 12 4 Move the jumper from the standard position pin 1 and pin 2 to the maintenance position pin 2 and pin 3 5 Install the computer cover and reconnect all cables and power cords that were disconnected See Completing the parts replacement on page 52 6 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 7 Insert the POST BIOS update flash disc into the optical drive Then select the optical drive as the startup device and press Enter The recovery session begins Note The recovery session will take two to three minutes During this time you will hear a series of beeps 8 After the recovery session is completed the series of beeps will end and the system will automatically turn off Remove the disc from the optical drive before the system completely turns off 9 Repeat steps 1 through 3 10 Move the Clear CMOS Recovery jumper back to the standard position pin 1 and pin 2 68 ThinkCentre User Guide 11 Install the computer cover and
8. reinstalling 52 computer lift stand 17 removing 17 connector 10 considerations password 64 creating and using a rescue medium 60 creating and using recovery media 57 CRU completing the installation 52 Customer Support Center 77 D Description 10 device drivers 53 installing 61 reinstalling 61 diagnostic programs troubleshooting 71 diagnostics programs using 77 DisplayPort out connector 10 documentation using 77 drivers device 53 E environment operating 5 Ethernet 2 Copyright Lenovo 2011 Ethernet connector 10 exiting Setup Utility program 66 expansion 2 ExpressCard replacing 39 external options installing 15 F features 1 flashing the BIOS 67 frame stand 16 removing 16 G getting help 75 information 75 service 75 H hard disk drive replacing 25 heat sink replacing 29 help Access Help 76 and service 77 getting 75 important safety information v information getting 75 important safety v resources 75 safety 76 warranty 76 Input Output I O features 2 installing device drivers 61 installing options memory module 22 security features 53 integrated cable lock security 53 integrated camera with microphone replacing 41 internal drives 1 internal speakers replacing 40 K keyboard connector 10 keyboard replacing 49 81 L Lenovo ThinkVantage Toolbox 72 Lenovo Web site 76 Lenovo Welcome 6 media creating and using recovery media 57 memory mod
9. 2 20 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up Remove the computer cover See Removing the computer cover on page 15 Remove the rear I O assembly cover from the rear I O assembly See Removing or reinstalling the rear I O assembly cover on page 19 Remove the frame stand or lift stand See Removing or reinstalling the frame stand on page 16 or Removing or reinstalling the lift stand on page 17 ThinkCentre User Guide 6 Remove the screw that secures the VESA frame cover slide the VESA frame cover to the bottom of the computer and then lift it up to remove it from the VESA frame Figure 10 Removing the VESA frame cover 7 To reinstall the VESA frame cover align the screw hole in the VESA frame cover with the corresponding hole in the VESA frame and then install the screw to secure the VESA frame cover What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Removing or reinstalling the VESA frame To remove or reins
10. FI card 34 Rescue and Recovery 57 workspace Rescue and Recovery 59 Rescue and Recovery workspace 59 resources information 75 right I O assembly replacing 46 S safety v safety information 76 security enabling or disabling 65 features 2 53 integrated cable lock 53 selecting startup device 65 temporary startup device 65 serial port 10 service and help 77 Customer Support Center 77 getting 75 services other 78 purchasing additional 78 Set Administrator Password 64 settings changing 63 viewing 63 Setup Utility program 63 Setup Utility program exiting 66 Setup Utility program starting 63 software recovering 57 software overview 6 solving recovery problems 62 starting the Setup Utility program 63 startup device 65 sequence changing 65 temporary selecting 65 system management 2 programs 67 system board locating parts 12 memory module 22 T television output notice 80 temporary startup device 65 the BIOS updating flashing 67 68 ThinkVantage Productivity Center 75 trademarks 80 troubleshooting basic 71 troubleshooting diagnostic programs 71 U updating flashing the BIOS 67 system programs 67 updating flashing the BIOS 68 USB connector 10 using a rescue medium creating and 60 diagnostic programs 77 documentation 77 other services 78 passwords 63 Setup Utility program 63 V VESA frame 21 removing 21 VGA IN connector 10 video subsystem 1 viewing and changing sett
11. access the ThinkVantage Productivity Center program click Start gt All Programs gt ThinkVantage gt Productivity Center Lenovo Welcome The Lenovo Welcome program introduces some innovative built in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer Access Help The Access Help information system provides information about getting started doing basic tasks customizing settings for your personal preference protecting data expanding and upgrading and troubleshooting e To open the Access Help information system on the Windows 7 operating system click Start gt Help and Support gt Lenovo Access Help e To open the Access Help information system on the Windows Vista operating system click Start gt All Programs gt ThinkVantage gt Access Help After you have opened the Access Help information system use the left panel to make a selection from the Contents tab or the Index tab or use the Search tab to find a particular word or phrase Safety and warranty The ThinkCentre Safety and Warranty Guide that came with your computer contains information about safety warranty service and support phone numbers CRUs and other notices and information resources Before using the information in this manual and the product it supports be sure to read and understand the ThinkCentre Safety and Warranty Guide and Appendix A Notices on page 79 Lenovo Web sit
12. com support 2 Use any CD DVD burning software to create a diagnostic disc with the ISO image Running the diagnostic program from the diagnostic disc This section provides instructions on how to run the diagnostic program from the diagnostic disc that you created To run the diagnostic program from the diagnostic disc that you created do the following 1 Make sure that your computer is turned off 2 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 Insert the diagnostic disc into the optical drive 4 Select the optical drive with the diagnostic disc as the startup device and press Enter The diagnostic program opens 5 Follow the instructions on the screen to run the desired diagnostic test For additional help press the F1 key Chapter 6 Troubleshooting and diagnostic programs 73 6 Remove the diagnostic disc from the optical drive after completing the diagnostic test Cleaning an optical mouse This section provides instructions on how to clean an optical mouse An optical mouse uses a LED and an optical sensor to navigate the pointer If the pointer on the screen does not move smoothly with the optical mouse you might need to clean the mouse To clean an optical mouse do the following 1 Turn off your computer 2 Disconnect the mouse cable from the computer 3 Turn the mouse upside down to view the lens a If there is a smudg
13. create You can create a rescue medium using a disc a USB hard disk drive or a secondary internal hard disk drive 5 Click OK and follow the instructions on the screen to create a rescue medium e To create a rescue medium on the Windows Vista operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Create Recovery Media The Create Rescue and Recovery Media window opens 2 In the Rescue Media area select the type of the rescue medium you want to create You can create a rescue medium using a disc a USB hard disk drive or a secondary internal hard disk drive 3 Click OK and follow the instructions on the screen to create a rescue medium Using a rescue medium This section provides instructions on how to use the rescue medium you have created e If you have created a rescue medium using a disc do the following to use the rescue medium 1 Turn off your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 On the Startup Device Menu select the desired optical drive as the first boot device Then insert the rescue disc into the optical drive and press Enter The rescue medium starts e If you have created a rescue medium using a USB hard disk drive do the following to use the rescue medium 1 Attach the USB hard disk drive to one of the USB connectors on your computer 2 Rep
14. e Set Administrator Password e Set Power On Password e Hard Disk Password You do not have to set a password to use your computer However using a password improves computing security If you decide to set a password read the following sections Copyright Lenovo 2011 63 Password considerations A password can be any combination of up to 64 1 to 64 alphabetic and numeric characters For security reasons it is recommended to use a strong password that cannot be easily compromised To set a strong password use the following guidelines Note The Setup Utility program passwords are not case sensitive e Have at least eight characters in length e Contain at least one alphabetic character and one numeric character e Not be your name or your user name e Not be a common word or a common name e Be significantly different from your previous passwords Administrator password The Set Administrator Password option enables you to set an administrator password which deters unauthorized users from changing configuration settings If you are responsible for maintaining the settings of several computers you might want to set an administrator password For more information on how to set a password see Setting changing or deleting a password on page 64 After you have set an administrator password a password prompt is displayed each time you try to access the Setup Utility program You cannot access the Setup Utility program until a
15. gt ThinkVantage gt Create Product Recovery Media Then follow the instructions on the screen Using recovery media This section provides instructions on how to use recovery media on the Windows 7 operating system Copyright Lenovo 2011 57 On the Windows 7 operating system and the Windows Vista operating system you can use recovery media to restore the computer to the factory default settings only You can use recovery media to put the computer in an operational state after all other methods of recovery have failed Attention When you use recovery media to restore the computer to the factory default settings all the files currently on the hard disk drive will be deleted and replaced by the factory default settings To use recovery media on the Windows 7 operating system or the Windows Vista operating system do the following 1 Depending on the type of your recovery media connect the boot medium memory key or other USB storage device to the computer or insert the boot disc into the optical drive 2 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 Select the desired startup device and press Enter The restore process begins 4 Follow the instructions on the screen to complete the operation Notes 1 After restoring your computer to the factory default settings you might have to reinstall device drivers for some devices See Install
16. on page 63 e Viewing or changing settings on page 63 e Using passwords on page 63 e Selecting a startup device on page 65 e Exiting the Setup Utility program on page 66 Starting the Setup Utility program This section provides instructions on how to start the Setup Utility program To start the Setup Utility program do the following 1 Make sure your computer is turned off 2 Repeatedly press and release the F1 key when turning on the computer When you see a logo screen release the F1 key The Setup Utility program opens Note If a password has been set the Setup Utility program menu will not be displayed until you type the correct password For more information see Using passwords on page 63 Viewing or changing settings The Setup Utility program menu lists various items about the system configuration settings To view or change the settings start the Setup Utility program See Starting the Setup Utility program on page 63 Then follow the instructions on the screen When working with the Setup Utility program you must use the keyboard The keys used to perform various tasks are displayed at the bottom of each screen Using passwords By using the Setup Utility program you can set a password to prevent unauthorized access to your computer and data The following options are available to help you set an administrator password a power on password or a hard disk drive password
17. replacement on page 52 Turn on the computer and leave it on for approximately 10 seconds Then turn off the computer by holding the power switch for approximately five seconds 7 Repeat step 1 through step 3 8 Move the Clear CMOS Recovery jumper back to the standard position pin 1 and pin 2 9 Close the computer cover and connect the power cord See Completing the parts replacement on page 52 Chapter 2 Installing or replacing hardware 55 56 ThinkCentre User Guide Chapter 3 Recovery information This chapter provides information about the recovery solutions provided by Lenovo This chapter contains the following topics e Creating and using recovery media on page 57 e Performing backup and recovery operations on page 58 e Using the Rescue and Recovery workspace on page 59 e Creating and using a rescue medium on page 60 e Installing or reinstalling device drivers on page 61 e Solving recovery problems on page 62 Notes 1 There are a variety of methods to choose from when considering how to recover in the event of a software or hardware related problem Some methods vary depending on the type of your operating system 2 The product on the recovery media may be used only for the following purposes e Restore the product preinstalled on your computer e Reinstall the product e Modify the product using the Additional Files Creating and using recovery media Y
18. 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Remove the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 5 Locate the Bluetooth module in the computer See Component locations on page 11 6 Note the Bluetooth module cable routing and disconnect the cable from the system board 7 Carefully release the Bluetooth module and lift the Bluetooth module out of the computer Figure 27 Removing the Bluetooth module 8 Position the new Bluetooth module into the computer front bezel and then press the new Bluetooth module downward until it is secured into place 9 Connect the new Bluetooth module cable to the system board See System board part and connector locations on page 12 10 Reinstall the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the par
19. 150 watt auto sensing power supply Security features Computrace Cover presence switch also called intrusion switch available in some models Enabling or disabling SATA devices Enabling or disabling the serial port Enabling or disabling USB connectors individually ThinkCentre User Guide Chapter 1 Product overview This chapter provides information about the computer features specifications preinstalled software programs and connector and part locations This chapter contains the following topics e Features on page 1 This section provides information about the computer features e Specifications on page 4 This section lists the physical specifications for your computer e Software overview on page 6 This section provides information about the software programs provided with your computer e Locating computer controls connectors and parts on page 7 This section provides information to help you locate your computer controls connectors and parts Features This section provides information about the computer features System information The following information covers a variety of models For information about your specific model use the Setup Utility program See Chapter 4 Using the Setup Utility program on page 63 Microprocessor Your computer comes with one of the following microprocessors internal cache size varies by model type e Intel Core i3 microprocessor e I
20. Chapter 2 Installing or replacing hardware 51 Notes To save your battery energy do the following when you are not using the wireless keyboard and mouse 1 Switch off the power button on the bottom of the wireless mouse 2 Disconnect the USB dongle from your computer and store it in the wireless mouse compartment Completing the parts replacement After completing the installation or replacement for all parts you need to reinstall the computer cover and reconnect cables To reinstall the computer cover and reconnect cables do the following 1 Make sure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer See Component locations on page 11 for the locations of various components in your computer 2 Make sure that the cables are routed correctly before reinstalling the computer cover Keep cables clear of the hinges and sides of the computer chassis to avoid interference with reinstalling the computer cover 52 ThinkCentre User Guide 3 Lower and position the computer cover into place and then slide the computer cover toward the bottom of the computer until the cover is secured into place Figure 40 Installing the computer cover 4 Lock the computer cover if you have an integrated cable lock See Integrated cable lock on page 53 and Rear view on page 9 5 Reconnect the external cables and power cord to the computer See Rear view
21. Note The ThinkVantage Productivity Center program is only available on computers preinstalled with the Windows Vista operating system from Lenovo Copyright Lenovo 2011 75 If possible be at your computer when you call Have the following information available e Machine type and model Serial numbers of your hardware products Description of the problem Exact wording of any error messages Hardware and software configuration information Using other services If you travel with your computer or relocate it to a country where your desktop or notebook computer machine type is sold your computer might be eligible for International Warranty Service which automatically entitles you to obtain warranty service throughout the warranty period Service will be performed by service providers authorized to perform warranty service Service methods and procedures vary by country and some services might not be available in all countries International Warranty Service is delivered through the method of service such as depot carry in or on site service that is provided in the servicing country Service centers in certain countries might not be able to service all models of a particular machine type In some countries fees and restrictions might apply at the time of service To determine whether your computer is eligible for International Warranty Service and to view a list of the countries where service is available go to http www lenovo com
22. Removing the power supply Remove the two screws Jj as shown in Removing the power supplyFigure 37 on page 48 that secure the power cord connector and then remove the power cord connector from the power cord connector bracket Install the two screws to secure the new power cord connector to the power cord connector bracket Position the new power supply in the computer and align the four screw holes in the new power supply with those in the computer main bracket Install the four screws to secure the new power supply Route the new power cord connector cable and then position the power cord connector bracket on the bottom of the computer main bracket Align the two screw holes in the power cord connector bracket with those in the computer main bracket and install the two screws to secure the power cord connector bracket Connect the new power supply cable to the power supply connector on the system board See System board part and connector locations on page 12 Reinstall the hard disk drive See Replacing the hard disk drive on page 25 Reinstall the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 48 ThinkCentre User Guide Replacing the keyboard Attention Do
23. The card reader is available only in some models To replace the card reader do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up Remove the computer cover See Removing the computer cover on page 15 Locate the card reader in the computer See Component locations on page 11 Disconnect the USB cable from the card reader Remove the two screws that secure the card reader and then lift the card reader out of the computer ona fk Ww ce I KIT Figure 34 Removing the card reader 7 Align the screw holes in the new card reader with those in the computer and then install the two screws to secure the card reader 8 Connect the USB cable to the new card reader What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 44 ThinkCentre User Guide Replacing the rear I O assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the
24. ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the rear I O assembly To replace the rear I O assembly do the following 1 2 7 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up Remove the computer cover See Removing the computer cover on page 15 Remove the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 Locate the rear I O assembly See Component locations on page 11 Remove the four screws fj that secure the rear I O assembly and then remove the rear I O assembly from the computer Figure 35 Removing the rear I O assembly To install the new rear I O assembly into the computer connect the new rear I O assembly to the rear I O assembly connector on the system board and then align the four screw holes with those in the computer main bracket See System board part and connecto
25. Works applications you must use the Microsoft Office CD or Microsoft Works CD These discs are provided only with computers preinstalled with Microsoft Office or Microsoft Works Creating and using a rescue medium With a rescue medium such as a disc or a USB hard disk drive you can recover the computer from failures that prevent you from gaining access to the Rescue and Recovery workspace on your hard disk drive Notes 1 The recovery operations you can perform using a rescue medium vary depending on the operating system 2 The rescue disc can be started in all types of optical drives 3 You can also run the PC Doctor for Rescue and Recovery diagnostic program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace Creating a rescue medium This section provides instructions on how to create a rescue medium on different operating systems e To create a rescue medium on the Windows 7 operating system do the following 60 ThinkCentre User Guide 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens 2 Inthe Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow 3 Click the Create Rescue Media icon The Create Rescue and Recovery Media window opens 4 Inthe Rescue Media area select the type of the rescue medium you want to
26. a new battery Figure 15 Installing a new battery 7 Reinstall the computer cover and connect the cables See Completing the parts replacement on page 52 Note When the computer is turned on for the first time after replacing the battery an error message might be displayed This is normal after replacing the battery 8 Turn on the computer and all attached devices 9 Use the Setup Utility program to set the date time and any passwords See Chapter 4 Using the Setup Utility program on page 63 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the hard disk drive To replace the hard disk drive do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the
27. an duct upward Figure 22 Removing the fan duct 30 ThinkCentre User Guide 6 Follow this sequence to remove the four screws that secure the heat sink to the system board a Partially remove screw then fully remove screw and then fully remove screw E b Partially remove screw then fully remove screw E and then fully remove screw EE Note Carefully remove the four screws from the system board to avoid any possible damage to the system board The four screws cannot be removed from the heat sink Figure 23 Removing the heat sink 7 Lift the failing heat sink off the system board Notes a You might have to gently twist the heat sink to free it from the microprocessor b Do not touch the thermal grease while handling the heat sink 8 Position the new heat sink on the system board so that the four screws are aligned with the corresponding holes in the system board 9 Follow this sequence to install the four screws to secure the heat sink as shown in Figure 23 Removing the heat sink on page 31 a Partially tighten screw ff then fully tighten screw and then fully tighten screw b Partially tighten screw then fully tighten screw and then fully tighten screw Eh 10 To reinstall the fan duct position the fan duct on the heat sink and then press the fan duct downward until the two tabs on the fan duct are secured into place What to do next e To work with another piece of hardware go to the appropr
28. ant safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the internal speakers To replace the internal speakers do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Remove the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 5 Locate the internal speakers in the computer See Component locations on page 11 6 Note the location of the internal speaker cable connection Note the routing of the internal speaker cables Disconnect the internal speaker cables from the system board 7 Remove the two screws that secure each internal speaker to the front bezel and then remove the internal speakers from the computer Figure 31 Removing the internal speakers 40 ThinkCentre User Guide 8 Route the new interna
29. ating system does not Verify that you list the device where the operating system resides in the startup start device sequence Usually the operating system is on the hard disk drive For more information see Selecting a startup device on page 65 The computer beeps multiple Verify that no keys are stuck times before the operating system starts Diagnostic programs Diagnostic programs are used to test hardware components of your computer Diagnostic programs can also report operating system controlled settings that interfere with the correct operation of your system The following programs are preinstalled on your computer to help you diagnose computer problems e Lenovo ThinkVantage Toolbox used when you are running the Windows operating system e PC Doctor for Rescue and Recovery used when you cannot start the Windows operating system Notes 1 You can also download the PC Doctor for DOS diagnostic program from http www lenovo com support See PC Doctor for DOS on page 73 for detailed information 2 If you are unable to isolate and repair the problem yourself after running the programs save and print the log files created by the programs You will need the log files when you speak to a Lenovo technical support representative Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox program helps you maintain your computer improve computing security diagnose computer problems get familiar with the inno
30. ation in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support Copyright Lenovo 2011 15 This section provides instructions on how to remove the computer cover CAUTION Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover To remove the computer cover do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove any locking device that secures the computer cover such as an integrated cable lock See Integrated cable lock on page 53 4 Press the two cover release buttons on the computer cover as shown slide the computer cover toward the top of the computer and then lift the computer cover up to remove it from the chassis Figure 5 Removing the computer cover Removing or reinstalling the frame stand Your computer might come with a frame stand or a lift stand This section provides instructions on how to remove or reinstall the frame stand For information about the lift stand see
31. available in some models 2 Your computer might come with a frame stand or a lift stand For more information about the lift stand see Removing or reinstalling the lift stand on page 17 System board part and connector locations Figure 4 System board part and connector locations on page 12 shows the locations of the parts and connectors on the system board p2 E ae FH a 27 E ma Vas 25 a 24 oo p 8 23 g LOO oo mm m Figure 4 System board part and connector locations EW Microprocessor Rear I O assembly connector E Multi touch board cable connector COM connector EJ Integrated camera cable connector Thermal sensor connector EJ Memory slots 2 Right I O assembly cable connector Ei Mini PC Express slot Hard disk drive power connector EJ Ambient light sensor cable connector HJ PS 2 keyboard and mouse connector 12 ThinkCentre User Guide Bluetooth module cable connector EJ Wireless keyboard and mouse connector EJ Clear Complementary Metal Oxide Semiconductor CMOS Recovery jumper Et Battery Microprocessor fan connector EH Internal speaker cable connector EEJ Power switch cable connector EZ ExpressCard connector EBJ SATA
32. ce opens after a short delay 3 From the Rescue and Recovery workspace select Launch advanced Rescue and Recovery gt Diagnose hardware The PC Doctor for Rescue and Recovery program opens 4 Select the desired diagnostic test Then follow the instructions on the screen For additional information about running the PC Doctor for Rescue and Recovery program refer to the PC Doctor for Rescue and Recovery help system Note If you encounter failures that prevent you from gaining access to the Rescue and Recovery workspace you can run the PC Doctor for Rescue and Recovery program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace See Creating and using a rescue medium on page 60 PC Doctor for DOS You can also download the latest version of the PC Doctor for DOS diagnostic program from http www lenovo com support The PC Doctor for DOS diagnostic program runs independently of the Windows operating system Use the PC Doctor for DOS diagnostic program if you are unable to start the Windows operating system You can run the PC Doctor for DOS diagnostic program from a diagnostic disc that you created Creating a diagnostic disc This section provides instructions on how to create a diagnostic disc To create a diagnostic disc do the following 1 Download a self starting bootable disc image known as an ISO image of the diagnostic program from http www lenovo
33. ches with a frame stand and frame foot 566 9 mm 22 32 inches with a lift stand e Depth ranges from 109 mm 4 29 inches to 250 mm 9 84 inches varies by configuration Computer weight Maximum configuration as shipped 14 1 kg 31 09 Ibs Touch screen dimensions Width 531 4 mm 20 92 inches Height 311 6 mm 12 27 inches Depth 2 mm 0 08 inch Lift stand Height adjustment 110 mm 4 33 inches Tilt adjustment 5 to 25 from the vertical Frame stand Tilt adjustment 15 to 45 from the vertical Environment e Air temperature Operating 10 C to 35 C 50 F to 95 F Non operating 20 C to 60 C 4 F to 140 F with package e Humidity Operating 20 to 80 10 per hour non condensing Non operating 20 to 80 10 per hour non condensing e Altitude Operating 50 to 10 000 ft 15 2 to 3 048 m Non operating 50 to 35 000 ft 15 2 to 10 668 m Electrical input e Input voltage Low range Minimum 100 V ac Maximum 127 V ac Input frequency range 50 to 60 Hz High range Minimum 200 V ac Maximum 240 V ac Input frequency range 50 to 60 Hz Chapter 1 Product overview 5 Software overview The computer comes with a preinstalled operating system and several preinstalled applications Software provided with your Windows operating system This section provides information about the software provided with your Windows operating system Software provided by Lenovo The following
34. computer cover on page 15 3 Locate the hard disk drive in the computer See Component locations on page 11 Chapter 2 Installing or replacing hardware 25 4 Pull the handle J of the hard disk drive bracket upward and then slide the hard disk drive outward to remove it from the hard disk drive bay Figure 16 Removing the hard disk drive 5 Flex the sides of the hard disk drive bracket properly to remove the hard disk drive out of the bracket 6 To install the new hard disk drive into the bracket flex the bracket and align pin ij pin Eh pin E and pin EJ on the bracket with the corresponding holes in the hard disk drive Do not touch the circuit board fj on the bottom of the hard disk drive Figure 17 Installing the hard disk drive into the bracket 26 ThinkCentre User Guide 7 Align the four pins ij on the hard disk drive bracket with the corresponding slots in the hard disk drive bay Figure 18 Installing the hard disk drive 8 Slide the new hard disk drive with the bracket into the hard disk drive bay Press the handle of the hard disk drive bracket downward until it is secured by the two tabs Figure 19 Installing the hard disk drive What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Chapter 2 Installing or replacing hardware 27 Replacing the optical dr
35. computer to help you set up use and maintain your computer It requires no Internet access to view the publication To view the publication click Start gt All Programs gt Online Books gt Online Books then double click the publication for your computer The publication is also available on the Lenovo Support Web site at http www lenovo com support Notes 1 The publication is in PDF version To view the publication you need to have the Adobe Reader program preinstalled on your computer If the Adobe Reader program has not been installed on your computer a message will be displayed when you attempt to view the PDF file and you will be guided through the Adobe Reader installation 2 The publication is available in other languages on the Lenovo Support Web site at http www lenovo com support 3 If you want to install a different language version of the Adobe Reader program rather than the version preinstalled on your computer download the desired language version from the Adobe Web site at http www adobe com Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program helps you work more easily and securely by providing easy access to various tools such as e Lenovo ThinkVantage Toolbox e Power Manager e Product Recovery e Rescue and Recovery e System Update To access the Lenovo ThinkVantage Tools program click Start gt All Programs gt Lenovo ThinkVantage Tools ThinkVantage Productivity Center
36. connector E SATA connector E Optical drive power connector EJ Low voltage differential signaling LVDS cable connector E System fan connector BJ Inverter connector Power supply fan connector EJ Power supply connector Chapter 1 Product overview 13 14 ThinkCentre User Guide Chapter 2 Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer This chapter contains the following topics e Installing or replacing hardware on page 15 e Obtaining device drivers on page 53 e Basic security features on page 53 Installing or replacing hardware This section provides instructions on how to install or replace hardware for your computer You can maintain your computer or expand the capabilities of your computer by installing or replacing hardware Notes 1 Use only computer parts provided by Lenovo 2 When installing or replacing an option use the appropriate instructions in this section along with the instructions that come with the option Installing external options You can install external options to your computer such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When you install an external option see Locating computer controls connectors and parts on page 7 to identify the required connector Then use the in
37. croprocessor in the socket 11 Reinstall the heat sink and the fan duct See Replacing the heat sink on page 29 12 Reinstall any other parts or reconnect any other cables you removed What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the WI FI card Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the WI FI card Note The WI FI card is available only in some models To replace the WI FI card do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 34 ThinkCentre User Guide Remove the computer cover See Removing the computer cover on page 15 Locate the WI FI card on the system board See Component
38. d you need to restore the hard disk drive to the factory default settings See Creating and using recovery media on page 57 Note If you are unable to access the Rescue and Recovery workspace or the Windows environment from a rescue medium or recovery media you might not have the rescue device an internal hard disk drive a disc a USB hard disk drive or other external devices set as the first boot device in the startup device sequence You must first make sure that your rescue device is set as the first boot device in the startup device sequence in the Setup Utility program See Selecting a startup device on page 65 for detailed information about temporarily or permanently changing the startup device sequence For more information about the Setup Utility program see Chapter 4 Using the Setup Utility program on page 63 It is important to create a rescue medium and a set of recovery media as early as possible and store them in a safe place for future use 62 ThinkCentre User Guide Chapter 4 Using the Setup Utility program You can use the Setup Utility program to view and change the configuration settings of your computer regardless of which operating system you are using However the operating system settings might override any similar settings in the Setup Utility program This chapter provides information about the following topics to help you use the Setup Utility program e Starting the Setup Utility program
39. devices that use a PS 2 mouse connector Used to attach an external modem a serial printer or other devices that use a 9 pin serial port Used to attach a device that requires a USB connector such as a USB keyboard a USB mouse a USB scanner or a USB printer If you have more than eight USB devices you can purchase a USB hub which you can use to connect additional USB devices Used to connect your computer to a VGA monitor connector on a second computer so that you can use your computer in monitor mode Component locations Figure 3 Component locations on page 11 shows the locations of the various components in your computer To remove the computer cover and access the inside of the computer see Removing the computer cover on page 15 Figure 3 Component locations E Frame stand E Video Electronics Standards Association VESA frame cover EJ Fan duct E Heat sink E Memory modules 2 g WI FI card Microprocessor fan EJ Battery E ExpressCard EQ Rear I O assembly Internal speaker EQ Frame foot Hard disk drive EJ Right 1 O assembly Card reader HJ Optical drive bay B Inverter E Computer main bracket E Optical drive EJ Power supply Chapter 1 Product overview 11 Internal speaker E Integrated camera with microphone Bluetooth module HJ Ambient light sensor FER System fan Multi touch board Rear I O assembly cover EJ VESA frame Notes 1 denotes optional parts which are
40. e http www lenovo com The Lenovo Web site provides up to date information and services to help you buy upgrade and maintain your computer You can also do the following e Shop for desktop and notebook computers monitors projectors upgrades and accessories for your computer and special offers e Purchase additional services such as support for hardware operating systems software programs network setup and configuration and custom installations e Purchase upgrades and extended hardware repair services e Download the latest device drivers and software updates for your computer model e Access the online manuals for your products e Access the Lenovo Limited Warranty e Access troubleshooting and support information for your computer model and other supported products e Find the service and support phone numbers for your country or region 76 ThinkCentre User Guide Chapter 7 Getting information help and service This chapter provides information about help service and technical assistance for Lenovo products This chapter contains the following topics e Information resources on page 75 e Help and service on page 77 Information resources You can use the information in this section to access useful resources relating to your computing needs Online Books folder The Online Books folder preinstalled on your computer contains the ThinkCentre User Guide which provides information about your
41. e 16 To remove or reinstall the lift stand do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up Chapter 2 Installing or replacing hardware 17 3 Remove the three screws that secure the lift stand Keep the three screws and put them aside You will need them when installing the lift stand Remove the lift stand from the computer Figure 7 Removing the lift stand 18 ThinkCentre User Guide 4 To reinstall the lift stand insert the two tabs J on the lift stand into the corresponding holes in the computer VESA frame and then slide the lift stand toward the bottom of the computer Align the three screw holes in the lift stand with those in the computer VESA frame and then install the three screws to secure the lift stand Figure 8 Reinstalling the lift stand What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Removing or reinstalling the rear I O assembly cover This section provides instructions on how to remove or reinstall the r
42. e as downloadable files on the Lenovo Web site at http www lenovo com Instructions for using the POST and BIOS updates are available in a TXT file that is included with the update files For most models you can download either an update program to create a system program update disc or an update program that can be run from the operating system Updating flashing the BIOS from a disc This section provides instructions on how to update flash the BIOS from a disc Note You can download a self starting bootable disc image known as an ISO image with the system program updates to create a system program update disc Go to http www lenovo com support To update flash the BIOS from a disc do the following 1 Turn off your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 On the Startup Device Menu select the desired optical drive as the first boot device Then insert the disc into the optical drive and press Enter The update begins 4 When prompted to change the serial number it is suggested that you press N However if you do want to change the serial number press Y then type in the serial number and press Enter Copyright Lenovo 2011 67 5 When prompted to change the machine type and model it is suggested that you press N However if you do want to change the machine type and model press Y then type in the machine
43. e on the lens gently clean the area with a plain cotton tipped swab b If there is debris in the lens gently blow the debris away from the area 4 Check the surface on which you are using the mouse If you have a very intricate picture or pattern beneath the mouse it may be difficult for the digital signal processor DSP to determine changes in the mouse position 5 Reconnect the mouse cable to the computer 6 Turn your computer back on 74 ThinkCentre User Guide Chapter 7 Getting information help and service This chapter provides information about help service and technical assistance for Lenovo products This chapter contains the following topics e Information resources on page 75 e Help and service on page 77 Information resources You can use the information in this section to access useful resources relating to your computing needs Online Books folder The Online Books folder preinstalled on your computer contains the ThinkCentre User Guide which provides information about your computer to help you set up use and maintain your computer It requires no Internet access to view the publication To view the publication click Start gt All Programs gt Online Books gt Online Books then double click the publication for your computer The publication is also available on the Lenovo Support Web site at http www lenovo com support Notes 1 The publication is in PDF version To view t
44. e power indicator on the front of the computer is on The computer voltage matches the voltage available at the electrical outlet for your country or region The monitor screen is blank Verify that The power cord is correctly connected to the rear of the computer and to a working electrical outlet The computer voltage matches the voltage available at the electrical outlet for your country or region The brightness and contrast controls are set correctly The USB keyboard or mouse Verify that dogs not wen The computer is turned on The USB keyboard or mouse is correctly connected to one of the USB connectors on the computer For the USB keyboard no keys are stuck The USB mouse is clean Refer to Cleaning an optical mouse on page 74 Copyright Lenovo 2011 71 symptom Cm The wireless keyboard or mouse Verify that does not work e The computer is turned on e The battery or batteries installed in the wireless keyboard or mouse are in good condition The wireless configurations are all set correctly You might need to refer to the documentation that come with the wireless keyboard or mouse or refer to your Windows Help and Support information system for wireless related instructions If your wireless mouse has a dongle make sure the dongle is correctly connected to one of the USB connectors on the computer e For the wireless keyboard no keys are stuck e The wireless mouse is clean The oper
45. ear I O assembly cover To remove or reinstall the rear I O assembly cover do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up Chapter 2 Installing or replacing hardware 19 Remove the computer cover See Removing the computer cover on page 15 Locate the rear I O assembly cover See Component locations on page 11 Carefully release the bottom of the rear I O assembly cover from the computer front bezel and then release the top of the rear I O assembly cover from the computer VESA frame cover Figure 9 Removing the rear I O assembly cover 6 To reinstall the rear I O assembly cover engage the bottom of the rear I O assembly cover with the computer front bezel and then press the top of the rear I O assembly cover downward until it snaps into place What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Removing or reinstalling the VESA frame cover To remove or reinstall the VESA frame cover do the following 1
46. eatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 On the Startup Device Menu select the USB hard disk drive as the first boot device and press Enter The rescue medium starts e If you have created a rescue medium using the secondary internal hard disk drive set the secondary internal hard disk drive as the first boot device in the startup device sequence to start the rescue medium See Selecting a startup device on page 65 Note The secondary internal hard disk drive is only available in some computer models When the rescue medium starts the Rescue and Recovery workspace opens The help information for each feature is available from the Rescue and Recovery workspace Follow the instructions to complete the recovery process Installing or reinstalling device drivers Before installing or reinstalling device drivers make sure that you have a preinstalled operating system and the documentation and software media for the device Device drivers for factory installed devices are located on the computer hard disk drive usually drive C in the SWTOOLS DRIVERS subdirectory The latest device drivers for factory installed devices are also available at http www lenovo com support Other device drivers are on the software media that come with individual devices Chapter 3 Recovery information 61 To install or reinstall the device driver for a factory in
47. equence do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 63 2 Select Startup gt Primary Boot Sequence Read the information displayed on the right side of the screen 3 Select the first boot device second boot device and so on 4 Press Esc to return to the Startup menu Then select the devices for the Automatic Boot Sequence and Error Boot Sequence 5 Press Esc to return to the Setup Utility program main menu You might have to press Esc several times 6 Press F10 to save the new settings and exit the Setup Utility program Notes a If you do not want to save the new settings select Exit gt Discard Changes and Exit b If you want to return to the default settings press F9 or select Exit gt Load Optimal Defaults Exiting the Setup Utility program After you finish viewing or changing settings press Esc to return to the Setup Utility program main menu You might have to press Esc several times Then you can do one of the following e f you want to save the new settings and exit the Setup Utility program press F10 or select Exit gt Save Changes and Exit Otherwise your changes will not be saved e f you do not want to save the new settings select Exit gt Discard Changes and Exit e If you want to return to the default settings press F9 or select Exit gt Load Optimal Defaults 66 ThinkCentre User Guide Chapter 5 Updating system programs Th
48. er contains the following topics e Features on page 1 This section provides information about the computer features e Specifications on page 4 This section lists the physical specifications for your computer e Software overview on page 6 This section provides information about the software programs provided with your computer e Locating computer controls connectors and parts on page 7 This section provides information to help you locate your computer controls connectors and parts Features This section provides information about the computer features System information The following information covers a variety of models For information about your specific model use the Setup Utility program See Chapter 4 Using the Setup Utility program on page 63 Microprocessor Your computer comes with one of the following microprocessors internal cache size varies by model type e Intel Core i3 microprocessor e Intel Core i5 microprocessor e Intel Pentium microprocessor Memory module s e Supports up to two double data rate 3 dual inline memory modules DDR3 DIMMs Note Your computer supports both 1066 MHz and 1333 MHz DDR3 memory modules However if you are using the 1333 MHz memory module s with a microprocessor that runs at 1066 MHz such as the Intel Pentium G6950 microprocessor your memory module s will operate at 1066 MHz Internal drives e One slim Serial Advanced Technolog
49. es that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Locate the integrated camera with microphone in the computer See Component locations on page 11 5 Note the routing of the integrated camera cable and then disconnect the integrated camera cable from the system board See System board part and connector locations on page 12 Chapter 2 Installing or replacing hardware 41 6 Remove the two screws J that secure the integrated camera with microphone to the front bezel and then remove the integrated camera with microphone from the computer Figure 32 Removing the integrated camera with microphone 7 Route the new integrated camera cable and then position the new integrated camera with microphone in place Align the two screw holes in the new integrated camera with microphone with those in the front bezel 8 Reinstall the two screws to secure the new integrated camera with microphone to the front bezel 9 Connect the integrated camera cable to the system board See System board part and connector locations on page 12 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to C
50. g or replacing hardware Installing or replacing hardware Installing external options Installing a computer wall mount Removing the computer cover Removing or reinstalling the frame siard Removing or reinstalling the lift stand Removing or oa the rear I O ARMEI cover Pa Removing or reinstaling the VESA fane cover Removing or rainstalling the VESA a Installing or replacing a memory module Replacing the battery Replacing the hard disk drive Replacing the optical drive Replacing the heat sink Replacing the microprocessor Replacing the WI FI card Replacing the Bluetooth module Replacing the multi touch board Replacing the ambient light sensor Replacing the ExpressCard Replacing the internal speakers Replacing the integrated camera with microphone Replacing the microprocessor fan Assemb Replacing the card reader Replacing the rear I O assembly Replacing the right I O assembly Replacing the power supply Copyright Lenovo 2011 lt or On 11 12 15 15 15 15 15 16 17 19 20 21 22 24 25 28 29 32 34 35 36 37 39 40 41 42 44 45 46 47 Replacing the keyboard Replacing the mouse Os Completing the parts replacement Obtaining device drivers Basic security features Integrated cable lock Password protection Erasing lost or forgotten eewo i iearing CMOS Chapter 3 Recovery information Creating and using recovery media Creatin
51. g recovery media Using recovery media ee Performing backup and recovery operations Performing a backup operation Performing a recovery operation Using the Rescue and Recovery workspace Creating and using a rescue medium Creating a rescue medium Using a rescue medium i Installing or reinstalling device drivers Solving recovery problems Chapter 4 Using the TPP ene program Starting the Setup Utility program Viewing or changing settings Using passwords Password considerations Administrator password Power on password Hard disk drive password bos Setting changing or deleting a password Enabling or disabling a device Selecting a startup device Bae cs Selecting a temporary startup device Viewing or changing the sais device sequence oe Exiting the Setup Utility program Chapter 5 PPANS ancy programs Using system programs Updating flashing the BIOS fain a disc Updating mene the BIOS from your Tepa system 49 50 52 53 53 53 54 54 57 57 57 57 58 58 59 59 60 60 61 61 62 63 63 63 63 64 64 64 64 64 65 65 65 65 66 67 67 67 68 Recovering from a POST BIOS update failure Chapter 6 Troubleshooting and diagnostic programs Basic troubleshooting Diagnostic programs Lenovo ThinkVantage Toolbox PC Doctor for Rescue and Recovery PC Doctor for DOS Cleaning an optical mouse Chapter 7 Getting information ses and ser
52. he publication you need to have the Adobe Reader program preinstalled on your computer If the Adobe Reader program has not been installed on your computer a message will be displayed when you attempt to view the PDF file and you will be guided through the Adobe Reader installation 2 The publication is available in other languages on the Lenovo Support Web site at http www lenovo com support 3 If you want to install a different language version of the Adobe Reader program rather than the version preinstalled on your computer download the desired language version from the Adobe Web site at http www adobe com Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program helps you work more easily and securely by providing easy access to various tools such as e Lenovo ThinkVantage Toolbox e Power Manager e Product Recovery e Rescue and Recovery e System Update To access the Lenovo ThinkVantage Tools program click Start gt All Programs gt Lenovo ThinkVantage Tools ThinkVantage Productivity Center Note The ThinkVantage Productivity Center program is only available on computers preinstalled with the Windows Vista operating system from Lenovo 75 The ThinkVantage Productivity Center program contains information sources and tools designed to make computing easy and secure It provides easy access to various technologies such as e Power Manager e Product Recovery e Rescue and Recovery e System Update To
53. iate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Chapter 2 Installing or replacing hardware 31 Replacing the microprocessor Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the microprocessor CAUTION The heat sink and microprocessor might be very hot Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover To replace the microprocessor do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Remove the fan duct and the heat sink from the system board See Replacing the heat sink on page 29 5 Lift the small handle lj and open the retainer J to access the micro
54. igure 28 Removing the multi touch board 7 Align the screw holes in the new multi touch board with those in the computer main bracket and then install the two screws to secure the multi touch board 8 Connect the new multi touch board cables to the system board and the multi touch screen See System board part and connector locations on page 12 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the ambient light sensor Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support Chapter 2 Installing or replacing hardware 37 This section provides instructions on how to replace the ambient light sensor Note The ambient light sensor is available only in some models To replace the ambient light sensor do the following 1 2 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gentl
55. ing or reinstalling device drivers on page 61 2 Some computers come with Microsoft Office or Microsoft Works preinstalled If you need to recover or reinstall your Microsoft Office or Microsoft Works applications you must use the Microsoft Office CD or Microsoft Works CD These discs are provided only with computers preinstalled with Microsoft Office or Microsoft Works Performing backup and recovery operations The Rescue and Recovery program enables you to back up all your hard disk drive contents including the operating system data files software programs and personal settings You can designate where the Rescue and Recovery program stores the backup e Ina protected area of your hard disk drive e On the secondary hard disk drive if a secondary hard disk drive is installed in your computer e On an attached external USB hard disk drive e On a network drive e On recordable discs a recordable optical drive is required for this option After you have backed up the contents on the hard disk drive you can restore the complete contents of the hard disk drive restore only the selected files or restore only the Windows operating system and applications Performing a backup operation This section provides instructions on how to perform a backup operation using the Rescue and Recovery program on different operating systems e To perform a backup operation using the Rescue and Recovery program on the Windows 7 operating system do
56. ings 63 W warranty information 76 Web site Lenovo 76 WI FI card replacing 34 workspace backup and recovery 59 Copyright Lenovo 2011 83 84 ThinkCentre User Guide lenovo Part Number 89Y8034 Printed in USA 1P P N 89Y8034
57. ion of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to Lenovo United States Inc 1009 Think Place Building One Morrisville NC 27560 U S A Attention Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product specifications or warranties Nothing in this document shall opera
58. is chapter provides information about updating the POST and BIOS and how to recover from a POST and BIOS update failure This chapter contains the following topics e Using system programs on page 67 e Updating flashing the BIOS from a disc on page 67 e Updating flashing the BIOS from your operating system on page 68 e Recovering from a POST BIOS update failure on page 68 Using system programs System programs are the basic layer of software built into your computer System programs include the POST the BIOS and the Setup Utility program The POST is a set of tests and procedures that are performed each time you turn on your computer The BIOS is a layer of software that translates instructions from other layers of software into electrical signals that the computer hardware can execute You can use the Setup Utility program to view or change the configuration settings of your computer See Chapter 4 Using the Setup Utility program on page 63 for detailed information Your computer system board has a module called electrically erasable programmable read only memory EEPROM also referred to as flash memory You can easily update the POST the BIOS and the Setup Utility program by starting your computer with a system program update disc or running a special update program from your operating system Lenovo might make changes and enhancements to the POST and BIOS When updates are released they are availabl
59. ith another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the heat sink Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the heat sink CAUTION The heat sink might be very hot Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover To replace the heat sink do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Locate the heat sink on the system board See Component locations on page 11 Chapter 2 Installing or replacing hardware 29 5 Remove the fan duct by pressing the two tabs J inward and then pivoting the f
60. ive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the optical drive Note The optical drive is available only in some models To replace the optical drive do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 amp Locate the optical drive See Component locations on page 11 oa Press the optical drive release button fj toward the top of the computer and then slide the optical drive out of the optical drive bay Figure 20 Removing the optical drive 28 ThinkCentre User Guide 6 To install a new optical drive slide the new optical drive into the optical drive bay until it snaps into position Figure 21 Installing the optical drive What to do next e To work w
61. k the Launch advanced Rescue and Recovery arrow 3 Click the Restore your system from a backup icon 4 Follow the instructions on the screen to complete the recovery operation e To perform a recovery operation using the Rescue and Recovery program on the Windows Vista operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Rescue and Recovery The Rescue and Recovery program opens 2 In the Rescue and Recovery main window click Launch advanced Rescue and Recovery 3 Click the Restore your system from a backup icon 4 Follow the instructions on the screen to complete the recovery operation For more information about performing a recovery operation from the Rescue and Recovery workspace see Using the Rescue and Recovery workspace on page 59 Using the Rescue and Recovery workspace The Rescue and Recovery workspace resides in a protected hidden area of your hard disk drive that operates independently from the Windows operating system This enables you to perform recovery operations even if you cannot start the Windows operating system You can perform the following recovery operations from the Rescue and Recovery workspace e Rescue files from your hard disk drive or from a backup The Rescue and Recovery workspace enables you to locate files on your hard disk drive and transfer them to a network drive or other recordable media such as a USB device or a disc This so
62. l speaker cables and then position the new internal speakers on the front bezel so that the two screw holes in each internal speaker align with those in the front bezel 9 Reinstall the two screws to secure each of the internal speakers to the front bezel 10 Reconnect the internal speaker cables to the system board See System board part and connector locations on page 12 11 Reinstall the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the integrated camera with microphone Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the integrated camera with microphone Note The integrated camera with microphone is available only in some models To replace the integrated camera with microphone do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cabl
63. lenovo ThinkCentre User Guide o Thinktentre Machine Types 0800 0852 0870 2471 2557 3091 3265 3373 3429 3650 3678 4285 5205 and 5248 lenovo ThinkCentre User Guide Machine Types 0800 0852 0870 2471 2557 3091 3265 3373 3429 3650 3678 4285 5205 and 5248 Note Before using this information and the product it supports be sure to read and understand the ThinkCentre Safety and Warranty Guide and Appendix A Notices on page 79 Second Edition May 2011 Copyright Lenovo 2011 LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 Contents Important safety information Chapter 1 Product overview Features Single touch dad mui PA feature Specifications Software overview Software provided with your rWindows operating system Locating computer controls connectors and parts id Front view Rear view ae Component locations o ne System board part and connector locations Chapter 2 Installin
64. locations on page 11 Disconnect the two cables from the WI FI card Carefully remove the two screws that secure the WI FI card to the system board Then pivot the WI FI card upward and lift the WI FI card to remove it from the mini PCI Express slot OORA Ww gt Wy y Figure 26 Removing the WI FI card 7 Insert the notched end of the new WI FI card into the mini PCI Express slot Press the new WI FI card firmly and then pivot the WI FI card to align the screw holes in the new WI FI card with those in the system board 8 Install the two screws to secure the new WI FI card to the system board 9 Connect the two cables to the new WI FI card What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the Bluetooth module Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the Bluetooth module Note The Bluetooth module is available only in some models Chapter 2 Installing or replacing hardware 35 To replace the Bluetooth module do the following
65. lution is available even if you did not back up your files or if changes were made to the files since your last backup operation You can also rescue individual files from a Rescue and Recovery backup located on your local hard disk drive a USB device or a network drive e Restore your hard disk drive from a Rescue and Recovery backup If you have backed up your hard disk drive using the Rescue and Recovery program you can restore the hard disk drive from a Rescue and Recovery backup even if you cannot start the Windows operating system e Restore your hard disk drive to the factory default settings The Rescue and Recovery workspace enables you to restore the complete contents of your hard disk drive to the factory default settings If you have multiple partitions on your hard disk drive you have the option to restore the factory default settings to the C partition and leave the other partitions intact Because the Rescue and Recovery workspace operates Chapter 3 Recovery information 59 independently from the Windows operating system you can restore the factory default settings even if you cannot start the Windows operating system Attention If you restore the hard disk drive from a Rescue and Recovery backup or restore the hard disk drive to the factory default settings all files on the primary hard disk drive partition usually drive C will be deleted in the recovery process If possible make copies of important files If you are unable
66. mine where to connect the cables on your computer _ 1 anane o E 10 11 a 13 r Lit m ri lt PD Figure 2 Rear connector locations E Card reader available in some models EJ Power cord connector H USB connector ET Integrated cable lock slot EJ Headphone connector Ethernet connector Chapter 1 Product overview 9 E Microphone connector H USB connector i Serial port available in some models PS 2 mouse connector available in some models USB connectors 4 DisplayPort out connector EZI VGA IN connector ExpressCard slot available in some models EJ PS 2 keyboard connector available in some models Connector DisplayPort out connector Ethernet connector Microphone connector PS 2 keyboard connector optional PS 2 mouse connector optional Serial port optional USB connector VGA IN connector 10 ThinkCentre User Guide Description Used to attach a high performance monitor a direct drive monitor or other devices that use a DisplayPort connector Used to attach an Ethernet cable for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to attach a microphone to your computer when you want to record sound or if you use speech recognition software Used to attach a keyboard that uses a PS 2 keyboard connector Used to attach a mouse a trackball or other pointing
67. not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the keyboard Replacing the PS 2 or USB keyboard To replace the PS 2 or USB keyboard do the following 1 Remove any media from the drives Then turn off all attached devices and the computer 2 Disconnect all power cords from electrical outlets 3 Locate the keyboard connector Note Your keyboard might be connected to a PS 2 keyboard connector J or a USB connector El Figure 38 Keyboard connectors 4 Disconnect the failing keyboard from the computer 5 Connect a new keyboard to the appropriate connector on the computer 6 Reconnect all power cords to electrical outlets Replacing the wireless keyboard To replace the wireless keyboard do the following 1 Take away your failing wireless keyboard 2 Remove the new wireless keyboard from the package Chapter 2 Installing or replacing hardware 49 3 Correctly install the batteries for the new wireless keyboard by referring to the following illustrations 4 Remove the USB dongle from the wireless mouse compartment and connect it to an available USB connectors on the computer See Replacing the wireless mouse
68. ntel Core i5 microprocessor e Intel Pentium microprocessor Memory module s e Supports up to two double data rate 3 dual inline memory modules DDR3 DIMMs Note Your computer supports both 1066 MHz and 1333 MHz DDR3 memory modules However if you are using the 1333 MHz memory module s with a microprocessor that runs at 1066 MHz such as the Intel Pentium G6950 microprocessor your memory module s will operate at 1066 MHz Internal drives e One slim Serial Advanced Technology Attachment SATA optical drive e One SATA hard disk drive Video subsystem e Integrated graphics card for a Video Graphics Array VGA IN connector and a DisplayPort out connector Audio subsystem e Integrated high definition HD audio e Microphone connector and headphone connector e Internal speakers Copyright Lenovo 2011 1 Table 1 Operating system edition and supported touch feature Windows 7 Professional Single touch or multi touch Windows 7 Starter Single touch Windows 7 Ultimate Single touch or multi touch Specifications This section lists the physical specifications for your computer 4 ThinkCentre User Guide Computer dimensions without a stand and frame foot Width 560 mm 22 05 inches Height 392 mm 15 43 inches Depth 79 mm 3 11 inches or 86 mm 3 39 inches varies by configuration Computer dimensions with a stand and frame foot e Width 560 mm 22 05 inches e Maximum height 421 9 mm 16 61 in
69. ogy that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited European conformance CE mark CE Trademarks The following terms are trademarks of Lenovo in the United States other countries or both Lenovo The Lenovo logo Personal System 2 PS 2 Rescue and Recovery ThinkCentre ThinkVantage Microsoft Windows and Windows Vista are trademarks of the Microsoft group of companies Intel Intel Core and Pentium are trademarks of Intel Corporation in the United States other countries or both Other company product or service names may be trademarks or service marks of others 80 ThinkCentre User Guide Index A a rescue medium creating and using 60 Access Help 76 Administrator password 64 ambient light sensor replacing 37 antivirus software 7 audio subsystem 1 backup and recovery operations 58 basic troubleshooting 71 battery replacing 24 Bluetooth module replacing 35 boot block recovery 68 C card reader replacing 44 changing startup device sequence 65 cleaning an optical mouse 74 CMOS clearing 54 computer cover removing 15 computer cover
70. ompleting the parts replacement on page 52 Replacing the microprocessor fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the microprocessor fan assembly To replace the microprocessor fan assembly do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 42 ThinkCentre User Guide Remove the frame stand or lift stand See Removing or reinstalling the frame stand on page 16 or Removing or reinstalling the lift stand on page 17 Remove the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 Remove the VESA frame cover See Removing or reinstalling the VESA frame cover on page 20 Note the routing of the micro
71. on page 9 6 Depending on the parts you installed or replaced you might need to confirm the updated information in the Setup Utility program Refer to Chapter 4 Using the Setup Utility program on page 63 Note In most areas of the world Lenovo requires the return of the defective Customer Replaceable Unit CRU Information about this will come with the CRU or will come a few days after the CRU arrives Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www lenovo com support Installation instructions are provided in readme files with the device driver files Basic security features There are several security options available to help you prevent hardware theft and unauthorized access to your computer In addition to physical locks you can also prevent unauthorized use of your computer by a software lock that locks the keyboard until a correct password is typed in Integrated cable lock Note Make sure that any security cables you installed do not interfere with other computer cables Chapter 2 Installing or replacing hardware 53 An integrated cable lock sometimes referred to as the Kensington lock can be used to secure your computer to a desk a table or other non permanent fixture The integrated cable lock attaches to the integrated cable lock slot in the rear of your computer and is operated with a key See Rear view on page 9 for the location of
72. or for Rescue and Recovery diagnostic program is preinstalled on your ThinkCentre computer as part of the Rescue and Recovery workspace to help you diagnose hardware problems It can also report operating system controlled settings that interfere with the correct operation of your system Use the PC Doctor for Rescue and Recovery diagnostic program if you are unable to start the Windows operating system For more information see PC Doctor for Rescue and Recovery on page 73 Adobe Reader The Adobe Reader program is a tool used to view print and search PDF documents See Online Books folder on page 75 for more information about accessing and viewing the publications Antivirus software Your computer comes with antivirus software that you can use to detect and eliminate viruses Lenovo provides a full version of antivirus software on your computer with a free 30 day subscription After 30 days you must renew the license to continue receiving the antivirus software updates For more information about how to use your antivirus software refer to the help system of your antivirus software Locating computer controls connectors and parts This section provides information to help you locate your computer controls connectors and parts Chapter 1 Product overview 7 Front view Figure 1 Front control and part locations on page 8 shows the locations of the controls and parts on the front of your computer
73. ou can use recovery media to restore the hard disk drive to the factory default settings Recovery media are useful if you transfer the computer to another area sell the computer recycle the computer or put the computer in an operational state after all other methods of recovery have failed As a precautionary measure it is important to create recovery media as early as possible Note The recovery operations you can perform using recovery media vary depending on the operating system from which the recovery media were created The recovery media might contain a boot medium and a data medium Your Microsoft Windows license permits you to create only one data medium so it is important that you store the recovery media in a safe place after you have made them Creating recovery media This section provides instructions on how to create recovery media on different operating systems Note On the Windows 7 operating system you can create recovery media using discs or external USB storage devices On the Windows Vista operating systems you can create recovery media using only discs so this operation is also called creating Product Recovery discs e To create recovery media on the Windows 7 operating system click Start gt All Programs gt Lenovo ThinkVantage Tools gt Factory Recovery Disks Then follow the instructions on the screen e To create Product Recovery discs on the Windows Vista operating system click Start gt All Programs
74. pressCard is available only in some models To replace the ExpressCard do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Locate the ExpressCard in the computer See Component locations on page 11 5 Carefully remove the four screws J that secure the ExpressCard to the system board and then lift it off the system board Figure 30 Removing the ExpressCard 6 Connect the new ExpressCard to the ExpressCard connector on the system board Align the screw holes in the new ExpressCard with the corresponding holes in the system board and then install the four screws to secure the new ExpressCard Chapter 2 Installing or replacing hardware 39 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the internal speakers Attention Do not open your computer or attempt any repair before reading and understanding the Import
75. processor E 6 Lift the microprocessor straight up and out of the socket See Figure 24 Removing the microprocessor on page 33 Notes a Your microprocessor and socket might look different from the one illustrated b Note the orientation of the microprocessor in the socket You can either look for the small triangle E on one corner of the microprocessor or note the orientation of the notches J on the microprocessor This is important when installing the new microprocessor on the system board 32 ThinkCentre User Guide c Touch only the sides of the microprocessor Do not touch the gold contacts on the bottom d Do not drop anything onto the microprocessor socket while it is exposed The socket pins must be kept as clean as possible Figure 24 Removing the microprocessor 7 Make sure that the small handle is in the raised position and the microprocessor retainer is fully open Chapter 2 Installing or replacing hardware 33 8 Hold the new microprocessor and align the notches on it with the alignment keys in the microprocessor socket or align the small triangle JJ on one corner of the new microprocessor with the corresponding beveled corner of the microprocessor socket Figure 25 Installing the microprocessor 9 Lower the new microprocessor straight down into the microprocessor socket on the system board 10 Close the microprocessor retainer and lock it into position with the small handle to secure the new mi
76. processor fan assembly cable and then disconnect the microprocessor fan assembly cable from the system board Remove the three screws J that secure the microprocessor fan assembly and then lift the microprocessor fan assembly off the system board Figure 33 Removing the microprocessor fan assembly 9 10 11 12 Position the new microprocessor fan assembly on the system board and align the three screw holes in the new microprocessor fan assembly with those in the system board Install the three screws to secure the microprocessor fan assembly to the system board Connect the microprocessor fan assembly cable to the system board See System board part and connector locations on page 12 Reinstall the VESA frame cover and the rear I O assembly cover What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Chapter 2 Installing or replacing hardware 43 Replacing the card reader Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the card reader Note
77. r locations on page 12 Chapter 2 Installing or replacing hardware 45 8 Install the four screws to secure the rear I O assembly to the computer main bracket 9 Reinstall the rear I O assembly cover See Removing or reinstalling the rear I O assembly cover on page 19 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Replacing the right I O assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the right I O assembly To replace the right I O assembly do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up Remove the computer cover See Removing the computer cover on page 15 Locate the right I O assembly See
78. reconnect all cables and power cords that were disconnected See Completing the parts replacement on page 52 12 Turn on the computer to restart the operating system Chapter 5 Updating system programs 69 70 ThinkCentre User Guide Chapter 6 Troubleshooting and diagnostic programs This chapter provides information about some basic troubleshooting and diagnostic programs If your computer problem is not described in this chapter see Chapter 7 Getting information help and service on page 75 for additional troubleshooting resources This chapter contains the following topics e Basic troubleshooting on page 71 e Diagnostic programs on page 72 e Cleaning an optical mouse on page 74 Basic troubleshooting The following table provides some basic information to help you troubleshoot your computer problems Note If you cannot solve the problem after doing the basic troubleshooting have the computer serviced Refer to the ThinkCentre Safety and Warranty Guide that came with your computer for the safety and warranty information and the list of service and support telephone numbers You can also get the latest service and support telephone numbers from the Lenovo Support Web site at http www lenovo com support a a The computer does not start Verify that when you press the power switch The power cord is correctly connected to the rear of the computer and to a working electrical outlet Th
79. s Esc several times 5 Press F10 to save the new settings and exit the Setup Utility program Notes a If you do not want to save the new settings select Exit gt Discard Changes and Exit b If you want to return to the default settings press F9 or select Exit gt Load Optimal Defaults Selecting a startup device If your computer does not start up from a device such as a hard disk drive or the disc in an optical drive as expected do one of the following to select the desired startup device Selecting a temporary startup device This section provides instructions on how to select a temporary startup device You can use the instructions in this section to start up from any startup device Note Not all discs and hard disk drives are bootable To select a temporary startup device do the following 1 Turn off your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 Select the desired startup device on the Startup Device Menu and press Enter to begin Note Selecting a startup device on the Startup Device Menu does not permanently change the startup device sequence Viewing or changing the startup device sequence This section provides instructions on how to view or permanently change the configured startup device sequence Chapter 4 Using the Setup Utility program 65 To view or permanently change the configured startup device s
80. set of self recovery tools to help you diagnose computer problems get help and recover from system crashes even if you cannot start the Windows operating system Power Manager The Power Manager program provides convenient flexible and complete power management for your ThinkCentre computer By using the Power Manager program you can adjust your power settings to achieve the best balance between system performance and power saving Password Manager The Password Manager program helps you automatically capture and fill in authentication information for Windows applications and Web sites ThinkVantage System Update The ThinkVantage System Update program helps you keep the software on your computer up to date by downloading and installing software packages ThinkVantage applications device drivers BIOS updates and other third party applications Some examples of software that you should keep updated are programs 6 ThinkCentre User Guide provided by Lenovo such as the Rescue and Recovery program and the ThinkVantage Productivity Center program Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox program helps you maintain your computer improve computing security diagnose computer problems get familiar with the innovative technologies provided by Lenovo and get more information about your computer For more information see Lenovo ThinkVantage Toolbox on page 72 PC Doctor for Rescue and Recovery The PC Doct
81. software programs are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer Software programs provided with your computer might vary depending on your model type and preinstalled operating system Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely For more information see Lenovo ThinkVantage Tools on page 75 ThinkVantage Productivity Center The ThinkVantage Productivity Center program guides you to a host of information sources and tools to help you set up understand and maintain your computer and enhance your computer performance For more information see ThinkVantage Productivity Center on page 75 Note The ThinkVantage Productivity Center program is only available on computers preinstalled with the Windows Vista operating system from Lenovo Lenovo Welcome The Lenovo Welcome program introduces some innovative built in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer Product Recovery The Product Recovery program enables you to restore the contents of the hard disk drive to the factory default settings ThinkVantage Rescue and Recovery The ThinkVantage Rescue and Recovery program is a one button recovery and restore solution that includes a
82. stalled device do the following 1 Turn on the computer N Use Windows Explorer or My Computer to display the directory structure of your hard disk drive Go to the C SWTOOLS directory Open the DRIVERS folder Within the DRIVERS folder there are several subfolders named for various devices installed in your computer such as AUDIO or VIDEO gt OQ 5 Open the appropriate device subfolder 6 Do one of the following e n the device subfolder look for a SETUP exe file Double click the file and follow the instructions on the screen to complete the installation e Inthe device subfolder look fora README txt file or a file with the txt extension This file might be named after the operating system such as WIN98 txt The TXT file contains information about how to install the device driver Follow the instructions to complete the installation e f the device subfolder contains a file with the inf extension and you want to install the device driver using the INF file refer to your Windows Help and Support information system for detailed information about how to install the device driver Solving recovery problems If you are unable to access the Rescue and Recovery workspace or the Windows environment do one of the following e Use a rescue medium to start the Rescue and Recovery workspace See Creating and using a rescue medium on page 60 e Use recovery media if all other methods of recovery have failed an
83. structions that come with the option to help you make the connection and install any software or device drivers that are required for the option Installing a computer wall mount CAUTION If you wish to perform a self installation of a wall mounting unit for this product Lenovo recommends that you select a wall mount product that is certified by Underwriters Laboratories UL Intertek ETL the Canadian Standards Association CSA NRTL TUV Rheinland of North America TUV US or any other safety test laboratory that is recognized by the United States Occupational Safety and Health Administration OSHA To avoid the risk of personal injury or damage to equipment self installers should ensure that the weight bearing capacity of the wall mount product is rated above 12 kg 26 5 Ibs so that it can support the machine for long time operation safely Your computer supports VESA standard 100 mm x 100 mm 3 94 inches x 3 94 inches wall mounts For proper mounting use four screws of the following specifications Diameter x Pitch x Length 4 mm x 0 7 mm x 10 mm 0 16 inch x 0 03 inch x 0 39 inch Note When installing a computer wall mount make sure that you leave at least a 60 mm 2 36 inches space between the wall and your computer for easy access to the connectors on the rear of your computer Removing the computer cover Attention Do not open your computer or attempt any repair before reading and understanding the Important safety inform
84. support This section provides instructions on how to replace the battery Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps the information active when you turn off the computer The battery normally requires no charging or maintenance throughout its life However if the battery fails the date time and configuration information including passwords are lost An error message will be displayed when you turn on the computer Refer to the Lithium battery notice in the ThinkCentre Safety and Warranty Guide for information about replacing and disposing of the battery To replace the battery do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Locate the battery on the system board See System board part and connector locations on page 12 5 Remove the battery t Figure 14 Removing the battery 24 ThinkCentre User Guide 6 Install
85. support click Warranty and follow the instructions on the screen For technical assistance with the installation of or questions related to Service Packs for your preinstalled Microsoft Windows product refer to the Microsoft Product Support Services Web site at http support microsoft com directory or you can contact the Customer Support Center Some fees might apply Purchasing additional services During and after the warranty period you can purchase additional services such as support for hardware operating systems and application programs network setup and configuration upgraded or extended hardware repair services and custom installations Service availability and service name might vary by country or region For more information about these services go to the Lenovo Web site at http www lenovo com 78 ThinkCentre User Guide Appendix A Notices Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services currently available in your area Any reference to a Lenovo product program or service is not intended to state or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operat
86. tall the VESA frame do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Remove the rear I O assembly cover from the rear I O assembly See Removing or reinstalling the rear I O assembly cover on page 19 5 Remove the frame stand or lift stand See Removing or reinstalling the frame stand on page 16 or Removing or reinstalling the lift stand on page 17 6 Remove the VESA frame cover See Removing or reinstalling the VESA frame cover on page 20 7 Disconnect the thermal sensor cable from the system board See System board part and connector locations on page 12 Chapter 2 Installing or replacing hardware 21 8 Remove the four screws fj that secure the VESA frame to the computer main bracket and then lift the VESA frame off the computer main bracket Figure 11 Removing the computer VESA frame 9 To reinstall the computer VESA frame position the VESA frame on the computer main bracket and align the screw holes in the VESA frame with
87. te as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment Copyright Lenovo 2011 79 Television output notice The following notice applies to models that have the factory installed television output feature This product incorporates copyright protection technol
88. the following 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens 2 In the Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow 3 Click Back up your hard drive and select backup operation options Then follow the instructions on the screen to complete the backup operation 58 ThinkCentre User Guide e To perform a backup operation using the Rescue and Recovery program on the Windows Vista operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Rescue and Recovery The Rescue and Recovery program opens 2 Inthe Rescue and Recovery main window click Launch advanced Rescue and Recovery gt Back up your hard drive and select backup operation options 3 Follow the instructions on the screen to complete the backup operation Performing a recovery operation This section provides instructions on how to perform a recovery operation using the Rescue and Recovery program on different operating systems e To perform a recovery operation using the Rescue and Recovery program on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens 2 Inthe Rescue and Recovery main window clic
89. the integrated cable lock slot This is the same type of lock used with many notebook computers You can order an integrated cable lock from Lenovo by searching for Kensington at http www lenovo com support Figure 41 Integrated cable lock Password protection To deter unauthorized use of your computer you can use the Setup Utility program to set a password When you turn on your computer you are prompted to type the password The computer cannot be used until a valid password is typed in Refer to Chapter 4 Using the Setup Utility program on page 63 for more information Erasing lost or forgotten passwords clearing CMOS This section provides instructions on how to erase lost or forgotten passwords such as a user password To erase a lost or forgotten password do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Remove the computer cover See Removing the computer cover on page 15 3 Locate the Clear CMOS Recovery jumper on the system board See System board part and connector locations on page 12 4 Move the jumper from the standard position pin 1 and pin 2 to the maintenance position pin 2 and pin 3 54 ThinkCentre User Guide Close the computer cover and connect the power cord See Completing the parts
90. those in the computer main bracket 10 Reinstall the four screws to secure the VESA frame to the computer main bracket 11 Reconnect the thermal sensor cable to the system board See System board part and connector locations on page 12 12 Reinstall the VESA frame cover See Removing or reinstalling the VESA frame cover on page 20 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to install or replace a memory module Your computer has two slots for installing or replacing DDR3 SODIMMs small outline dual inline memory modules When installing or replacing a memory module use 1 GB 2 GB or 4 GB DDR3 SODIMMs in any combination up to a maximum of 8 GB of system memory To install or replace a memory module do the following 22 ThinkCentre User Guide 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outle
91. to start the Windows operating system you can use the rescue files feature of the Rescue and Recovery workspace to copy files from your hard disk drive to other media To start the Rescue and Recovery workspace do the following 1 Make sure the computer is turned off 2 Repeatedly press and release the F11 key when turning on the computer When you hear beeps or see a logo screen release the F11 key 3 If you have set a Rescue and Recovery password type your password when prompted The Rescue and Recovery workspace opens after a short delay Note If the Rescue and Recovery workspace fails to open see Solving recovery problems on page 62 4 Do one of the following e To rescue files from your hard disk drive or from a backup click Rescue files and follow the instructions on the screen e To restore your hard disk drive from a Rescue and Recovery backup or to restore your hard disk drive to the factory default settings click Restore your system and follow the instructions on the screen For more information about the features of the Rescue and Recovery workspace click Help Notes 1 After restoring your hard disk drive to the factory default settings you might have to reinstall device drivers for some devices See Installing or reinstalling device drivers on page 61 2 Some computers come with Microsoft Office or Microsoft Works preinstalled If you need to recover or reinstall your Microsoft Office or Microsoft
92. ts and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Locate the memory slots See Component locations on page 11 5 Open the retaining clips If you are replacing an old memory module open the retaining clips and remove the old memory module as shown Figure 12 Removing the memory module 6 Insert the notched end J of the new memory module into the slot Press the memory module firmly and pivot the memory module until it snaps into place Make sure that the memory module is secured in the slot and does not move easily Figure 13 Installing a memory module What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 Chapter 2 Installing or replacing hardware 23 Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com
93. ts replacement on page 52 Replacing the multi touch board Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the multi touch board Note The multi touch board is available only in some models 36 ThinkCentre User Guide To replace the multi touch board do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Place a soft clean towel or cloth on the desk or surface Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up 3 Remove the computer cover See Removing the computer cover on page 15 4 Locate the multi touch board in the computer See Component locations on page 11 5 Note the multi touch board cable routing and disconnect the three multi touch board cables from the system board and the multi touch screen 6 Carefully remove the two screws Ef that secure the multi touch board and then lift the multi touch board off the computer main bracket F
94. type and model and press Enter 6 Follow the instructions on the screen to complete the update After the update is completed remove the disc from the optical drive Updating flashing the BIOS from your operating system Note Because Lenovo makes constant improvements to its Web sites the Web page contents are subject to change without notice including the contents referenced in the following procedure To update flash the BIOS from your operating system do the following 1 Go to http www lenovo com support 2 Do the following to locate the downloadable files for your machine type a In the Enter a product number field type your machine type and click Go b Click Downloads and drivers c Select BIOS from the Refine results drop down list box to easily locate all the BIOS related links d Click the BIOS update link 3 Click the TXT file that contains the instructions for updating flashing the BIOS from your operating system 4 Print these instructions This is very important because these instructions will not be displayed on the screen after the download begins 5 Follow the printed instructions to download extract and install the update Recovering from a POST BIOS update failure If the power to your computer is interrupted while the POST BIOS is being updated flash update your computer might not restart correctly If this happens perform the following procedure commonly called Boot block Recovery 1
95. ule installing 22 system board 22 Microphone connector 10 microprocessor fan assembly replacing 42 mouse connector 10 mouse replacing 50 multi touch board replacing 36 N notice television output 80 notices 79 O Online Books folder 75 operations backup and recovery 58 optical drive replacing 28 optical mouse cleaning 74 P parts replacement completing 52 password Administrator password 64 considerations 64 Hard disk drive password 64 Power on password 64 setting changing deleting 64 password protection 54 passwords erasing 54 lost or forgotten 54 PC Doctor for Rescue and Recovery 73 physical specifications 4 power supply features 2 power supply replacing 47 Power on password 64 power on self test POST 67 programs updating system 67 protection password 54 purchasing additional services 78 R rear I O assembly replacing 45 recovering a POST BIOS update failure 68 82 ThinkCentre User Guide software 57 recovery boot block 68 operations backup and 58 problems solving 62 recovery media creating and using 57 reinstalling device drivers 61 removing computer cover 15 replacing ambient light sensor 37 battery 24 Bluetooth module 35 card reader 44 ExpressCard 39 hard disk drive 25 heat sink 29 integrated camera with microphone 41 internal speakers 40 microprocessor fan assembly 42 multi touch board 36 power supply 47 rear I O assembly 45 right I O assembly 46 WI
96. valid password is typed in If you have set both a user password and an administrator password you can type either password to use your computer However to change any configuration settings you must use your administrator password Power on password After you have set a power on password using the Set Power On Password option a password prompt is displayed each time you turn on the computer You cannot use the computer until a valid password is typed in For more information about how to set a password see Setting changing or deleting a password on page 64 Hard disk drive password The Hard Disk Password option enables you to set a hard disk drive password which prevents unauthorized access to the data on the hard disk drive When a hard disk drive password is set you are prompted to type a valid password each time you try to access the hard disk drive For more information on how to set a hard disk drive password see Setting changing or deleting a password on page 64 Setting changing or deleting a password This section provides instructions on how to set change or delete a password To set change or delete a password do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 63 2 From the Setup Utility program main menu select Security 3 Depending on the password type select Set Administrator Password Set Power On Password or Hard Disk Password 4
97. vative technologies provided by Lenovo and get more information about your computer You can use the diagnostics feature of the Lenovo ThinkVantage Toolbox program to test devices diagnose computer problems create bootable diagnostic media update system drivers and view system information e To run the Lenovo ThinkVantage Toolbox program on the Windows 7 operating system click Start gt All Programs gt Lenovo ThinkVantage Tools gt System Health and Diagnostics Follow the instructions on the screen e To run the Lenovo ThinkVantage Toolbox program on the Windows Vista operating system click Start gt All Programs gt ThinkVantage gt Lenovo ThinkVantage Toolbox Follow the instructions on the screen For additional information about running the Lenovo ThinkVantage Toolbox program refer to the Lenovo ThinkVantage Toolbox help system 72 ThinkCentre User Guide PC Doctor for Rescue and Recovery The PC Doctor for Rescue and Recovery diagnostic program is part of the Rescue and Recovery workspace on your Lenovo computer Use the PC Doctor for Rescue and Recovery program if you are unable to start the Windows operating system To run the PC Doctor for Rescue and Recovery program from the Rescue and Recovery workspace do the following 1 Turn off the computer 2 Repeatedly press and release the F11 key when turning on the computer When you hear beeps or see a logo screen release the F11 key The Rescue and Recovery workspa
98. vice Information resources Online Books folder Lenovo ThinkVantage Tools ThinkVantage Productivity Center iv ThinkCentre User Guide 68 71 71 72 72 73 73 74 75 75 75 75 75 Lenovo Welcome Access Help Safety and warranty Lenovo Web site http www lenovo com Help and service Using the documentetion an diagnostic programs Calling for service Using other services Purchasing additional services Appendix A Notices Television output notice European conformance CE mark Trademarks Index 76 76 76 76 77 77 77 78 78 79 80 80 80 81 Important safety information CAUTION Before using this manual be sure to read and understand all the related safety information for this product Refer to the ThinkCentre Safety and Warranty Guide that you received with this product for the latest safety information Reading and understanding this safety information reduces the risk of personal injury and or damage to your product If you no longer have a copy of the ThinkCentre Safety and Warranty Guide you can obtain a Portable Document Format PDF version from the Lenovo Support Web site at http www lenovo com support Copyright Lenovo 2011 vi ThinkCentre User Guide Chapter 1 Product overview This chapter provides information about the computer features specifications preinstalled software programs and connector and part locations This chapt
99. y Attachment SATA optical drive e One SATA hard disk drive Video subsystem e Integrated graphics card for a Video Graphics Array VGA IN connector and a DisplayPort out connector Audio subsystem e Integrated high definition HD audio e Microphone connector and headphone connector e Internal speakers Connectivity 10 100 1000 Mbps Ethernet controller System management features Ability to store the power on self test POST hardware test results Advanced Configuration and Power Interface ACPI support Automatic power on startup Desktop Management Interface DMI Intel Active Management Technology AMT available in some models Intel Rapid Storage Technology Preboot Execution Environment PXE System Management SM Basic Input Output System BIOS and SM software Wake on LAN Windows Management Instrumentation WMI Input Output I O features One DisplayPort connector One Ethernet connector One optional 9 pin serial port One optional card reader One optional ExpressCard slot One optional Personal System 2 PS 2 keyboard connector One optional PS 2 mouse connector One VGA IN connector Six Universal Serial Bus USB connectors Two audio connectors microphone connector and headphone connector Wireless keyboard and mouse available in some models For more information about I O features see Rear view on page 9 Expansion One hard disk drive bay One optical drive bay Power supply
100. y lay it down so that the screen is against the surface and the cover is facing up Remove the computer cover See Removing the computer cover on page 15 Locate the ambient light sensor in the computer See Component locations on page 11 Carefully remove the two screws fj that secure the ambient light sensor and then lift the ambient light sensor out of the computer Figure 29 Removing the ambient light sensor Disconnect the ambient light sensor cable from the system board Align the screw holes in the new ambient light sensor with the corresponding holes in the computer and then install the two screws to secure the ambient light sensor Connect the new ambient light sensor cable to the system board See System board part and connector locations on page 12 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 52 38 ThinkCentre User Guide Replacing the ExpressCard Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the ExpressCard Note The Ex

Lanzar Car Audio 1801D Car Amplifier User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents