Home

Land Pride 357-044M Lawn Mower User Manual

1. 34 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 4 Maintenance amp Lubrication Table of Contents IMPORTANT Blade mounting bolts have right hand threads Turn blade bolts counterclockwise to loosen and clockwise to tighten 1 Remove blades by grasping the blade end with a rag or thick padded glove while loosening the blade mounting bolt 2 With a 11 16 wrench remove the 1 2 center blade bolt and Washer from the bottom of the blade IMPORTANT Replace blades with Land Pride blades only IMPORTANT Always install blades with cutting edge facing direction of blade spindle rotation and with wing tips pointing up towards bottom of deck 3 Reinstall blade blade washer and bolt Care should be taken when installing the blade bolt to not get it cross threaded 4 Tighten blade bolt to 135 ft lbs of torque Blade Sharpening 4 CAUTION ALWAYS wear eye protection and gloves when sharpening a blade NOTE Care should be taken in order not to remove any more material than necessary to sharpen blade 1 Ifthe blade cutting edge is dull or nicked it should be replaced or sharpened 2 Clean blade blade washer and mounting surface of all debris before replacing or sharpening 3 Sharpen blades on a grinder following pattern as shown in Figure 4 13 Grind cutting edge atthe same bevel 27 1 2 degrees as the or
2. on removal and installation Replace filter annually or after every 100 hours of operation whichever occurs first Be sure to Install the fuel filter with Flow Arrow pointing towards the engine side of the fuel line Always check fuel line hoses for any cracks or leaks Replace as needed Flow Arrow Indicates direction fuel must flow through the filter Fuel Filter Figure 4 7 Draining The Fuel Tank 1 Park the unit on a flat surface Make sure blade engagement switch is in the down OFF position Place control levers in park and set park lever to ON Stop engine and remove ignition key 2 Disconnect negative battery cable 3 Trace the fuel line from the tank to the tee under the Left Right Fuel Tank Valve Refer to Figure 4 8 Loosen the fuel line hose clamp at the tee and remove the fuel line from the tee 4 Place the end of the fuel line into a gas can or adrain pan to drain the fuel tank 5 When the fuel tank is drained re route the fuel line to the Left Right Fuel Tank Valve and reattach with previously removed clamp Left Right Fuel Tank Valve J Center Position O as Shown is OFF 5 Fuel Shut Off Valve Honda Engine Location Shown Figure 4 8 Engine Oil and Oil Filter Refer to Figure 4 9 Check engine oil daily and after every 4 hours of operation Crankcase dipstick and engine oil fill tube are located atthe rear of the machine Mower must be sitting level when checking oil Refer to engine
3. 831 038C Air Filter Paper 831 054C 831 036C Fuel Filter Replaceable Automotive Type Land Pride Part No 831 035C Cooling Air cooled Fly wheel fan Z44 amp Z52 Accu Z Razor General Specifications Width of Cut Trim Capacity left side Overall width Tire to tire width Height 39 Overall Length without hitch plate 67 9 w Honda Engine 68 7 w Briggs amp Stratton Engine Weight 720 lbs w Honda Engine 735 lbs w Honda Engine 709 lbs w Briggs amp Stratton Engine 724 lbs w Briggs amp Stratton Engine Drive Tires 18 x 8 5 8 turf tread 18 x 9 5 8 turf tread Front Tires 11 x 4 00 5 rib tire Starter 12 volt 8 KW solenoid shift positive engagement w Honda Engine 12 volt 8 KW industrial Starter w Briggs amp Stratton Engine Ignition Electronic Charging System 12 volt 20 amp w Honda Engine 12 volt 16 amp w Briggs amp Stratton Engine Governor Mechanical Fuel Unleaded gasoline with octane rating of 87 or higher Fuel Capacities 12 US GAL Traction Drive Type Dual Hydrostatic Transmission Hydraulic Drive Oil 20W 50 Mobil oil Hydraulic Oil Capacity 2 4 qts or 77 oz Hydraulic Motor Pumps Two variable displacement axial piston type Hydraulic Motor Pump Drive V belt drive from engine crankshaft Specifications to continue on next page 2 27 07 244 8 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 35
4. Adjustment on page 22 9 Re install deck belt covers 10 Re attach the negative battery cable and floor panel Drive Belt Viewed from the Bottom Drive motors removed for clarity Figure 4 10 figure 1 1 Deck drive belt 6 Deck belt idler eee Ea eo 2 Engine pulley 8 Fixed idler pulley 2 Deck blade spindle pulley 7 Idler arm 3 a 3 Electric clutch pull 5 Ovet centertensioner 3 Electric clutch pulley 9 Clutch restraint bracket i C Cue pu ey 9 Gusiconicrrslenss 4 Pump tension idler pulley 10 1 4 20 x 5 8 GR5 Hex 4 Spindle belt tension idler Use 3 4 socket wrench 5 Pump idler arm ee 5 Tension idler spring 6 Pump pulley 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 33 Table of Contents Section 4 Maintenance amp Lubrication Land Pride Drive Belt Replacement Instructions Refer to Figure 4 11 on page 33 1 Park unit on a flat surface Stop engine and remove ignition key Make sure blade engagement switch is in the down OFF position Spread control levers fully apart and set park to ON Ay WARNING Make sure engine and engine muffler is completely cooled before working on and around the drive belt Server burns to the body could result if engine and muffler have not cooled 2 Disconnect negative battery cable 3 Place deck height in the lowest position 4 Remove deck
5. Danger Guard Missing 6 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Introduction Table of Contents Land Pride welcomes you to the growing family of new product owners This mower has been designed with care and built by skilled workers using quality materials Proper assembly maintenance and safe operating practices will help you get years of satisfactory use from the machine Application The Accu Z Razor Mowers from Land Pride are compact in size and ideal for homeowner grass maintenance The Razor is a true zero turn mower When mowing alongside a building or landscaping the Razor allows you to turn away and not hit anything with the rear end Also the control lever heights are adjustable making the mower comfortable to handle See Section 5 Specifications amp Capacities on page 39 and Section 6 Features and Benefits on page 41 for additional information and performance enhancing options Using This Manual e This Operator s Manual is designed to help familiarize you with safety assembly operation adjustments troubleshooting and maintenance Read this manual and follow the recommendations to help ensure safe and efficient operation The information contained within this manual was current at the time of printing Some parts may change slightly to assure you of the best performance To order a new Operator s or Par
6. Manual Honda 18 HP P N 31ZJ4620 Honda 20 HP P N 31ZJ4620 B amp S 20 HP 276245 5 05 B amp S 25 HP 276245 5 05 1 770 497 6400 1 800 999 9333 Honda Service Hotline B amp S Service Hotline Serial Number Plate For prompt service always use the serial number and model number when ordering parts from your Land Pride dealer Be sure to include your serial and model numbers in correspondence also Refer to Figure 1 for the location of your serial number plate 4 YA Y Serial Number Plate Location Figure 1 Further Assistance Your dealer wants you to be satisfied with your new mower If for any reason you do not understand any part of this manual or are not satisfied with the service received the following actions are suggested 1 Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you 2 If you are still not satisfied seek out the owner or general manager of the dealership explain the problem and request assistance 3 For further assistance write to Land Pride Service Department 1525 East North Street P O Box 5060 Salina Ks 67402 5060 E mail address IpservicedeptO landpride com 2 27 07 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 7 Table of Contents Section 1 Assembly amp Set up Uncrating Instructions The crate is assemb
7. Refer to Figure 4 2 The battery is located under the seat The electrical system is a 12 volt negative ground Recommended battery size is a garden mower BCI group U1R with 225 or better cranking AMP rating A maintenance free battery is recommended Otherwise follow battery manufacturer s maintenance safety storing and charging specifications S eh Battery Figure 4 2 A WARNING Acid can cause serious injury to skin and eyes Avoid skin contact with battery acid and always wear eye protection when checking the battery Flush area with clean water and call a physician immediately Acid will also damage clothing A WARNING Do not allow an open flame near the battery when charging Hydrogen gas forms inside the battery This gas is both toxic and flammable and may cause an explosion if exposed to a flame A WARNING Incorrect battery cable connections can damage mower s electrical system and cause battery cables to spark Sparks around a battery can result in a battery gas explosion and personal injury e Always disconnect negative black battery cable before disconnecting positive red cable e Always reconnect positive red battery cable to the positive post before reconnecting negative black cable to the negative post A WARNING Keep battery terminals from touching any metal mower parts when removing or installing the battery Do not allow metal tools to short between the battery termina
8. TRAVEL REVERSE TRAVEL FORWARD TRAVEL LEFT TURN N Neutral Position Direction of arrows indicate direction of mower movement REVERSE TRAVEL RIGHT TURN Steering Figure 2 8 Moving Mower with Stalled Engine Refer to Figure 2 9 Each hydro drive is equipped with a bypass valve for the purpose of moving the mower when the engine is inoperable To bypass the hydro drives pull out on the bypass valve rods and lift them into the slot to lock in position Both bypass valve rods are located at the rear of the engine platform The park lever must be down OFF to move the mower IMPORTANT Do not tow the machine Move it by hand or use a winch and load it on a trailer IMPORTANT Following repairs always make certain the two bypass valves are returned to their operating position before operating the mower PIVOT RIGHT TURN 23801 Bypass Valve Rods Bypass Valve Figure 2 9 23643 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 15 Table of Contents Section 2 Operating Procedures Land Pride Safe Operating Instructions The safe operation of any machinery is a big concern to all consumers Your Zero Turn Riding Mower has been designed with many built in safety features However
9. drive belt 1 in Figure 4 10 from the electric clutch pulley 3 as outlined in Deck Belt Replacement Instructions on Page 33 This belt does not need to be removed from any of the other deck pulleys 5 Release belt tension from the IZT units 6 by pulling on the idler pulley 4 extending spring 7 carefully and sliding the belt over the pulley Use caution when releasing the idler pulley as there is still tension on it and it will snap back into position 6 Remove clutch restraint bracket 9 by removing the two 1 4 20 GR5 hex flange head screws and hex flange nuts 10 7 Slide the belt off and above the engine pulley 2 The belt will have to be slid above the engine pulley to allow the belt to be removed from the other pulleys Refer to Figure 4 12 AO YE Drive Belt on 221 ws K Engine Pulley oy Pump Motor Belt Removal Figure 4 12 8 Slide the belt over the IZT pulleys 6 9 Slide the belt off of the fixed idler pulley 8 10 The belt can now be removed from above the engine pulley 2 11 Install new belt by sliding it up and over the engine pulley 2 Make certain it is not in the pulley groove at this time but is above the pulley 12 Slide the belt over the fixed idler pulley 8 and then over the IZT pulleys 6 13 Slide the belt onto the engine pulley 2 14 Pull the idler pulley 4 over and slide the belt onto it Make certain to keep fingers from getting be
10. hole and seep out When finished screw cap back on securely and wipe up any spilled gasoline Use regular unleaded gasoline with an octane rating of 87 or higher IMPORTANT Never use methanol gasoline containing more than 10 ethanol because the fuel system could be damaged Do not mix oil with gasoline Using a fuel stabilizer conditioner in the fuel can provide benefits such as 1 Keeps gasoline fresh during storage of 90 days or less For longer storage drain the fuel tanks 2 Cleans the engine during operation 3 Eliminates gum like varnish build up in the fuel system IMPORTANT Do not use fuel additives containing methanol or ethanol Add the correct amount of gas stabilizer conditioner to the gas Follow the gas stabilizer conditioner manufacturer s directions for best results 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 31 Table of Contents Section 4 Maintenance amp Lubrication Land Pride Fuel Filter Refer to Figure 4 7 A DANGER Close fuel shut off valve before replacing fuel filter Otherwise fuel can leak out creating a fire and or explosion hazard The fuel filter is installed in the fuel line between the Left Right Fuel Tank Valve and engine fuel pump Location of fuel filter will vary depending on which engine your mower is equipped with See engine owner s manuals for exact location of fuel filter and instructions
11. left control lever and reassemble the bolts flat washers and locknuts in the same order they were removed without tightening them c Pivotthe upper control levers forward or backward to fit operator s personal reach preference 2 Verify that the control levers align with each other when in the neutral position and tighten the locknuts to the correct torque FET 7 SAD Y Upper Control Lever lt lt J mats gt y yA Bolts with Flat g Washers and Locknuts Es ZN pao ama A T Figure 3 4 Forward Travel Adjustment Refer to Figure 3 4 Reach Adjustment instructions are for adjusting the control levers to be equally aligned while in neutral However with this adjustment the mower may want to steer slightly to the right or left when pushing the levers equally forward Make the following adjustments if you prefer to have the levers equally aligned while in forward travel position instead of while in neutral position 1 While driving forward make the necessary steering correction required to make the unit go straight and take careful notice of how the upper control levers are positioned The distance one lever is ahead of the other to make the mower travel straight 2 Stop the mower on a level surface place the control levers in neutral shut the power off and remove the switch key 3 Either adjust the upper trailing lever forward by the distance it was trailing or adjust the up
12. manual and maintenance schedule for oil recommendation and capacities Change the engine oil and filter after the first 5 hours of operation and per the engine manufacturer s recommendations after that It is recommended oil be changed more frequently if the mower is being operated in extremely dirty conditions Cas IO S77 i ESA JEANS Crankcase Dipstick eo LA al L me LA Engine Oil a O N D Filler Tube l Cie aay Ny Lt agti VY y A a ON Bumper Removed for Clarity Oil Filter Drain amp Filler Tube Honda Engine Shown Figure 4 9 The oil fill and dipstick are located on the right hand side for the Honda engine and left hand side for the Briggs amp Stratton engine The oil drain and oil filter are located on the right hand side for both engines Drain oil by unscrewing the oil drain plug see Figure 4 9 as needed to allow oil to flow freely Do not remove drain plug Drain plug will offer resistance once it is unscrewed as far as it should be IMPORTANT Make certain engine is level and you are inserting the dipstick correctly when checking oil An oil overfill can cause engine problems Oil Check Honda Engine 1 Unscrew oil filler cap dipstick and wipe it clean 2 Insert dipstick fully in without screwing it in and removing it again to check oil level 3 If oil level is near or below the lower limit mark on the dipstick fill with
13. no one should operate this mower before carefully reading this Operator s Manual Also read all instructions noted on the safety decals A Be familiar with all functions of this mower A Do not operate a mower with damaged parts Repair all damages and defective parts before putting mower back in to service A Keep all bystanders away from this mower during operation A Do not allow anyone to operate this mower who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of this mower A Do not allow anyone under 16 years of age to operate this mower A No riders allowed Carrying a rider can result in injury and or death to the rider and operator A Do not operate mower while drinking or under the influence of alcohol or drugs A Always park on level ground place control levers in park set park lever to ON and remove ignition key before leaving the mower The mower could move before the park lever is set to ON if not stopped on level ground A Do not leave mower unattended with engine running A Always operate mower with belt guards installed Do not leave pulleys and belts exposed A Wear snug fitting clothing to avoid entanglement with moving parts A Keep hands feet long hair clothing and jewelry away from moving parts and obvious pinch points to avoid getting caught A Always be aware of and avoid tree limbs and brush that have a potential of hitting and or poking
14. one while riding the mower Serious body harm could result A Always wear long pants safety glasses and safety shoes Some conditions may warrant extra safety gear to be worn such as safety helmets A Do not touch engine engine exhaust pipe and or muffler while they are hot A Use extreme caution when driving through dry grass brush and other fire hazard materials Never stop or park over combustible materials Keep grass and brush from collecting on and around engine and muffler parts A Battery fumes are explosive A spark will ignite battery fumes Wear a face shield when charging or jumping a battery Follow all battery safety rules outlined in this manual A Avoid battery acid spills Do not get battery acid on eyes face or other body parts Flush eyes and other body parts immediately with water for at least 15 minutes if battery acid has gotten on them A Do not operate this mower on streets highways public roads or where it may be a hazard to faster moving traffic A Never attempt wheelies jumps or other stunts Never drive recklessly Always operate your mower at a safe speed that will allow you to maintain control A Never modify engine RPM or any parts on the mower without authorization Unauthorized modifications will void warranty to all parts directly and indirectly affected by the modification A Do not pull a trailer or implement exceeding a gross weight of 300 pounds and 50 pounds tongue weight Loss of con
15. recommended oil to the upper limit mark Do not overfill 4 Reinstall oil filler cap dipstick by screwing it in firmly Oil Check Briggs amp Stratton Engine 1 Unscrew oil filler cap dipstick and wipe it clean 2 Insert dipstick fully in by screwing it in and removing it again to check oil level 3 If oil level is near or below the lower limit mark on the dipstick fill with recommended oil to the upper limit mark Do not overfill 4 Reinstall oil filler cap dipstick by screwing it in firmly 32 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 4 Maintenance amp Lubrication Table of Contents Engine Air Filter Perform engine air filter maintenance per the engine operator s manual General Engine Maintenance Detailed instructions and recommendations for break in and regular maintenance are specified in the engine operator s manual Please refer to this manual for engine servicing lubricating oil levels with quality and viscosity recommendations bolt torques etc The engine warranty is backed by the engine manufacturer Special attention should be paid to applicable data which is not duplicated here Belt Replacement Refer to Figure 4 10 and Figure 4 11 Replace belts that show signs of severe cuts tears excessive weather checking cracking and or burns Slight raveling of belt covering does not indicate belt damage Tri
16. smooth operation move levers slowly avoid sudden movement Skill and ease of operation come with practice and experience Inexperienced operators may have a tendency to over steer and lose control Slow moving practice maneuvers are recommended to become familiar with these characteristics before attempting normal speed operation Sharp depressions or raised obstacles such as gutters or curbs should not be directly approached at high speed in an attempt to jump them as the operator could be thrown from the mower Approach at a slow speed and angle one drive wheel at the obstruction Continue at an angle until both wheels clear the obstruction When turning on soft wet turf keep both wheels rolling either forward or backward Pivoting on one stopped wheel can damage turf Peak mowing performance is maintained when the throttle is set at full rom This gives maximum power to the drive wheels and deck when needed Use the control levers to control ground speed rather than engine rpm Keep blades sharp Many problems with incorrect cutting patterns are due to dull blades or blades which have been sharpened incorrectly Information on sharpening blades is listed in this manual s maintenance section In addition most communities have individuals or companies which specialize in sharpening mower blades Blade sharpness should be checked daily Use high blade speed Your Razor is designed to operate at full throttle The throttle s
17. temperatures and hot weather periods Refer to Engine Owner s Manual 2 Torque lug nuts initially and after first 2 hours of operation 3 Refer to Engine Owner s Manual 4 Inspect pump and deck belt tensions every 6 months or 100 hours and replace if worn or cracking is noticed Otherwise replace every 200 hours or 2 years whichever comes first 5 Check fuel line hoses fuel valve and grommet for any cracks or leaks 6 Clean air cleaner more often under dusty conditions or when airborne debris is present Replace air cleaner if very dirty 7 Initial transaxle hydraulic oil and filter change is after the first 50 hours of operation Thereafter change transaxle hydraulic oil and filter ever 200 hours of operation 8 X M Service per hours indicated in column or monthly whichever comes first 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 27 Table of Contents Section 4 Maintenance amp Lubrication Land Pride Maintenance Ay WARNING Read and observe all safety warnings in this manual and in the engine service manual A WARNING Except when checking or changing components always keep protective shields on for safety as well as for cleanliness Ay WARNING Keep your machine clean and remove any deposits of trash and clippings which can cause engine fires and hydraulic overheating as well as excessive belt wear WARNING DO NOT have
18. warranty The seat platform is slotted so the seat can be adjusted to the operator Loosen the seat mounting hardware located under the seat and adjust the seat forward or rearwards to a length that is comfortable for the operator to raise and lower the mower deck with his right foot Tighten the seat mounting hardware once the seat is adjusted Upper Control Lever Adjustments IMPORTANT Do not make adjustment to the lower control levers since they are already adjusted for neutral creep on page 20 The control levers may be adjusted while in the neutral position for height reach and forward travel to fit the operator s steering comfort zone Height Adjustment Refer to Figure 3 4 1 Adjust control levers vertically by removing the bolts flat washers and locknuts that attach the upper control levers to the lower control levers 2 Reposition upper control levers to a height that fits the operator s personal preference 3 Reassemble bolts flat washers and locknuts in the same order they were removed without tightening them Reach Adjustment Refer to Figure 3 4 1 Pivotthe upper control levers forward or backward to fit the operator s personal reach preference If reach comfort zone can not be achieved then try exchanging sides the levers are located a Remove the bolts flat washers and locknuts that attach the upper control levers to the lower control levers b Switch right control lever with
19. 00000 eee 25 Pivot Front Wheels 0000 25 Section 4 Maintenance amp Lubrication 26 Maintenance Locations 26 Maintenance Schedule o o o o o 27 Maintenance 000 eee eee eee 28 Torque Values o oooccccccooc eee 28 A slg ease alee Ble Wis ee alee el 29 Electrical System 0 000 eee eee 29 Access to IZT Units 05 30 Hydraulic System ooooooooooooo 30 Hydraulic oil and Filter 30 Fuel System 20 0 es 31 Fuel Filter n aaan asap Stas a lass las a lag at lap elas atlas a ag easing 32 Draining The Fuel Tank 04 32 Engine Oil and Oil Filter 32 Oil Check Honda Engine 32 Oil Check Briggs amp Stratton Engine 32 Engine Air Filter 0 0 00 33 General Engine Maintenance 33 Belt Replacement o oooooococcocoo o 33 Deck Belt Replacement Instructions 33 Drive Belt Replacement Instructions 34 Mower Blade Maintenance 34 Strage escena a id ai ad dao 36 Preparation of Engine for Storage 36 New Season Preparation o o o o 36 Lubrication Points 0 0005 37 Center Blade Spindle 37 Left Blade Spindle 37 Right Blade Spindle 37 Gauge Wheel Bearing Zerk 38 Fron
20. 44 16 811 fpm and 52 18 937 fpm Assures a good finish cut Heavy duty high lift blades are 20 thick to handle the wear with a high lift design to stand the grass up before cutting Made from highest quality Marbain steel for longer blade life 1 Blades spindles with ball bearings handle heavy shock loads Single belt drive Single belt design offers easier maintenance over multiple belt designs less expensive to maintain Electric clutch control Park Safety Lockout Hydro Gear IZT Zero Turn Transaxle drive unit on each rear wheel Choice of Honda or premium Briggs Intek Series Engines and 18 20 or 25 HP The engine is centered and oriented for maximum ease of service Electric start Easy and smooth engagement of the mower blade drive system Control levers can not be bumped into forward or reverse accidently without manually setting the park lever to OFF Each mower has a homeowner friendly integrated hydrostatic transaxle containing a pump and drive motor for each rear wheel Except for changing hydraulic filters these units are self contained and are maintenance free Makes it possible for you to buy more value performance and power for your dollar Engine orientation provides for increased air flow around engine fins to help extend engine life Also it provides for a shorter overall mower length with more leg room available Spark plugs air cleaner choke and throttle can be serviced fro
21. 7 044M 39 Table of Contents Land Pride Section 5 Specifications amp Capacities Z44 amp Z52 Accu Z Razor General Specifications Ground Speed Forward 0 7 MPH Reverse 0 5 MPH Steering Type Twin Lever Steering Controls Twin lever steering provides independent control of each drive wheel Speed forward reverse brake and turns Steering Turning Radius Brake Service True zero degree Turns with counter rotating independent drive wheels Hydrostatic dynamic braking Parking Mower Drive Lever applied pawl and cog wheel Single V belt with electric clutch and spring tension idler pulley Safety Features Mainframe Construction Operator presence system connected to deck and drive clutches Molded vinyl seat Bolt loosening required for forward and reverse adjustments Optional armrests kit for standard molded vinyl seat Optional deluxe cushion seat with arm rests 1 1 2 square solid steel Drive Motor Mount Front Caster Wheels 1 8 welded steel Mounted with roller bearings on each wheel Front Caster Forks Deck Thickness 3 8 steel 11 Gauge decks with reinforcements welded into spindle mount areas Box Section Reinforced Front Edge Deck Trim Edges 11 GA x 3 1 2 x 1 1 2 Box Solid 1 x 3 8 steel bars for reinforced impact area Deck Housing Depth Deck Lift Hand Operated Controls 4 1 8 deep room for high capacity mowing Foot operated de
22. Hour Meter 00000 eee 11 COMO Savia ata 11 Ignition Switch o ooooocoooooooooo o 11 NFOUIG dara wae 11 CHOKE ciar ria 11 Blade Engagement Switch 12 Left Right Fuel Tank Valve 12 Control Levers lt td 12 Paik Levels a E A 12 Deck Lift Pedal oo o oooooo 13 Safety Start Interlock SysteM 13 Engine Starting 2 000 0 eee ooo 13 Driving the Mower 00 eee eee 14 To Start and Increase Speed 14 To Decrease Speed or Stop 14 Steering naci beads bP ees 14 Moving Mower with Stalled Engine 15 Safe Operating Instructions 16 Mower Deck Operation 445 18 General Operating Information 18 Section 3 Adjustments 19 Torque Values 000 cee eee eee 19 Steering Linkage 20e cee e eee 19 Control Lever Neutral Adjustment 20 Steering Dampener 2000000 20 Seat Adjustment 0 cece eee eee 21 Upper Control Lever Adjustments 21 Copyright 2006 All rights Reserved Hydro Drive Belt Adjustment 22 Deck Drive Belt Adjustment 22 Engine RPM Setting 2 00 22 Deck Leveling amp Height Adjustment 22 Deck Level Adjustments 22 Deck Cutting Height Adjustment 25 Anti Scalp Rollers 2
23. OTE The engine starter should not be operated for periods longer then 30 seconds at a time An interval of at least two minutes should be allowed between such cranking periods to protect the starter from overheating and burn out 5 Perform test to make sure safety start interlock system is operating properly Refer to Safety Start Interlock System on Page 13 6 As soon as engine begins to run check to make certain the oil warning light is off If not stop engine immediately and check for the cause Refer to Troubleshooting on page 42 7 Allow the engine to idle a few minutes before advancing the throttle and or engaging the blade clutch 8 Before stopping the engine place control levers in park position with park lever up ON Disengage the blade engagement switch e Throttle back to low idle for one minute to allow accumulated raw fuel to escape the muffler during engine slow down e Rotate ignition key counter clockwise to the OFF position e Remove key from switch before leaving the seat Driving the Mower Ay WARNING In the event of a system shutdown while mowing spread control levers fully apart and set park lever to ON to aid slowing and stopping the mower See Figure 2 5 on Page 12 A DANGER When going in reverse push forward gently on control levers and avoid sudden movement Any sudden movement could cause the front of the mower to come off of the ground resulting in possi
24. Table of Contents Mowers accu Z Razor Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers In Ri 357 044M Operator s Manual Read the Operator s manual entirely When you see this symbol the subsequent instructions and warnings are serious follow without exception Your life and the lives of others depend on it 2 27 07 Copyright 2006 Printed hh lt o Q 5 gt E S o S 2 a S 9 lt 1 y 2 lt a S 8 S not supplied with standard unit Table of Contents Important Safety Information 1 Safety at All TiMeS o ooooooooo 1 Safety Labels oooooccccoooooooooo 4 Introduction cir ie tied eee dwn 7 Application 0 00000 cee ee 7 Using This Manual 0 000 7 Owner Assistance 00 cee eee eee 7 Section 1 Assembly amp Set up 8 Uncrating Instructions 4 Control Lever Assembly 055 8 Seat Assembly 0 0000 e eee ee eee 8 Hitch Plate Assembly 00 0c eeee 8 Electrical Cable Connection 9 Engine Preparations 00 sees 9 Remove Mower From Crate Floor 9 Section 2 Operating Procedures 10 Mower Features 0 0 0 ee eee ee 10 Operating Check List 11 Instrumentation 0 020020 o 11 Engine Oil Pressure Light 11
25. a safety hazard to the operator and bystanders Not enough belt tension may also lead to premature belt damage due to excessive belt slippage IMPORTANT Do not over tension the spring to compensate for a badly worn belt or pulley o Y UU ky ar Normal Spring ngh 4 3 4 1 8 Spring Extension 24562 Deck Drive Belt Adjustment Figure 3 6 an E SS PS Counterclockwise to Release Belt Tension Engine RPM Setting The Razor is designed so that the engine will run at 3600 rpm static pump load only At this speed the hydraulic pumps are running at their maximum rated speed Deck Leveling amp Height Adjustment The mower deck has three areas that may need to be checked and adjusted periodically Before considering any mower deck leveling adjustments check that the tire air pressure is within the specified range A WARNING Stop engine Make sure blade engagement switch is in the down OFF position Place control levers in park position and set park lever to ON before leaving machine Deck Level Adjustments Leveling the deck must be done in the following order 1 Check tire pressures to make certain they are properly inflated before leveling deck Tire Inflation Chart Inflation PSI Drive Wheels 8 12 Gauge Wheels 8 12 2 Park the unit on a flat surface Refer to Figure 3 7 3 Raise deck fully up 4 Position the blade cutting height at 3 1 4 by placing 3 high d
26. afely to the ground 9 Remove breather assembly located on top of pump and add 20W 50 Mobil oil 10 Check oil level Oil level should be 1 7 8 from top of case port 11 Reinstall breather assembly into case port 12 Wipe off excess oil A degreaser may need to be used to remove excess oil Fuel System A DANGER Replacement of fuel system parts i e gas caps hoses fuel tanks fuel filters etc must be the same as original parts Fire and or explosion can occur if not followed Observe safe fuel handling precautions Do not smoke while handling fuel Do not fill tank with engine running or while engine is hot Allow the engine to cool before filling Spilling fuel over the engine muffler or a hot object may result in a fire or explosion Allow engine to cool before servicing the fuel system Do not fill fuel tanks to the top if mowing on hilly terrain or in hot weather Gas can rise up to the fuel cap vent hole and seep out Clean up any gasoline spills immediately Keep fuel away from open flame or spark Store the mower away from open flame or spark if there is fuel in the tank Use extra caution when handling gasoline and other fuels They are flammable and vapors are explosive A fire or explosion from gasoline can burn you and others and can damage property Refuel outdoors preferably or in well ventilated areas Never attempt to start engine when there is a strong odor of gasoline fumes present Locate an
27. al thread diameter in inches threads per in 1380 2960 2190 4100 1 3 8 6 890 655 1470 3230 2380 2 N m newton meters 13 8 12 1010 745 1670 3680 2710 3 ft lb foot pounds 1 1 2 6 1180 870 1950 4290 3160 4mm x pitch nominal thread diameter in millimeters x 11 2 12 1330 logo 2970 2190 4820 3560 thread pitch Torque tolerance 0 15 of torquing values Unless otherwise specified use torque values listed above Additional Torque Values Drive Wheel Lug Nuts 1 2 20 UNF 75 ft lbs Blade Spindle bolts 1 2 20 UNF x 2 GR8 135 ft lbs Pulley bolts before Installing pulleys 5 8 11 UNC x 3 1 2 GR5 130 ft lbs Electric Clutch Bolt 7 16 20 UNF x 3 GR5 50 ft lbs Tire Inflation Chart Tire Inflation PSI Drive Wheels 8 to 12 Gauge Wheels 8 to 12 44 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Section 8 Appendix Warranty Land Pride warrants to the original purchaser that this Land Pride product will be free from defects in material and workmanship beginning on the date of purchase by the end user according to the following schedule Residential use 2 years from date of delivery on all materials amp workmanship Residential purpose means use of product on same lot as your ho
28. and Pride liable for damages of any kind direct consequential or contingent to property Furthermore Land Pride shall not be liable for damages resulting from any cause beyond its reasonable control This Warranty does not extend to loss of crops any expense or loss for labor supplies rental machinery or for any other reason No other warranty of any kind whatsoever express or implied is made with respect to this sale and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale This Warranty is not valid unless registered with Land Pride within 30 days from the date of purchase by the end user 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 45 Corporate Office P O Box 5060 Salina Kansas 67402 5060 USA www landpride com
29. ap and fuel tank cap to make certain they are securely in place New Season Preparation Before starting the mower following post season storage the following servicing is required IMPORTANT Do not use a high pressure washer on or around the IZT units Water intrusion will result and void the IZT warranty 1 Clean mower removing trash and dirt accumulation 2 Check engine oil level 3 Tighten any bolts that have loosened and make sure all hair pins cotter pins and clevis pins are in place 4 Install all safety shields and review safety precautions listed in this manual Check and inflate tires to 8 12 psi Fill fuel tank with fresh gasoline Reconnect spark plug leads to spark plug Run machine at half speed for 5 minutes checking operation of the control levers Stop engine and check for oil leaks loose fittings and so forth ONO 36 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Section 4 Maintenance amp Lubrication Lubrication Points Center Blade Spindle Through opening between front shields 1 Zerk Type of Lubrication Multi purpose Grease Quantity As required Left Blade Spindle Under lower edge of pulley cover 1 Zerk Type of Lubrication Multi purpose Grease Quantity As required Right Blade Spindle Under lower edge of pulley cover 1 Zerk Type of Lubrication Multi pu
30. ate with the control levers in neutral 7 Turn ignition switch off place control levers in park and set park lever to ON Remove support blocking and safely lower mower wheels to the floor Steering Dampener Refer to Figure 3 3 The steering dampeners located under the seat are incorporated into the unit to provide some resistance when control levers are moving forward or rearward Make sure steering dampeners are adjusted properly by moving control levers to the reverse position and releasing them If control levers return to neutral position they are working correctly Adjust control levers if they do not return to neutral Adjusted as follows 1 Place control lever in neutral position 2 Adjust left dampener rod a Loosen nut on the left front ball stud b Pull dampener spring housing to the rear past the point that the internal spring is engaged c Release dampener spring housing and allow the internal spring to bring the housing back to neutral position d Retighten left front ball stud nut rotating O a AO Pump Linkage Rod O 1 Jam Nut i E E O h Ao LENT N 0684 Jam Nut Steering Control Linkage Figure 3 2 4 If wheel is rotating forward a Loosen jam nuts on the pump linkage rod b Rotate rod to lengthen the steering control lin
31. ble loss of control To Start and Increase Speed Refer to Figure 2 8 on page 15 After starting the engine engage control levers by moving the handles towards each other This moves the levers from park position to neutral position and makes them ready for steering while traveling Moving control levers an equal distance away from neutral will increase travel speed Start forward travel by gently pushing on the control levers The further forward the control levers are pushed the faster the travel speed e Start backing up by gently pulling on the control levers The further back the control levers are pulled the faster the travel speed To Decrease Speed or Stop Refer to Figure 2 8 on page 15 Moving control levers an equal distance towards neutral will decrease travel speed When moving forward pull back gently on control levers to decrease speed The further back the control levers are pulled the slower the travel speed until neutral is reached e When backing up push forward gently on control levers to decrease speed The further forward the control levers are pushed the slower the travel speed until neutral is reached e Move control levers to neutral to stop e Spread both control levers fully apart and set park lever to ON to apply park brakes A DANGER Never make sudden stops or sudden reversing of direction especially when going down a slope The steering is designed for sensitive response Rapid
32. calp rollers are standard on the Razor These anti scalp rollers are designed to minimize scalping when mowing on rough uneven terrain UA 4 hm E Anti Scalp Rollers Anti Scalp Roller Adjustment Figure 3 15 After setting the cutting height adjust the front anti scalp rollers so they extend below the deck but do not contact the ground They should always be at least 1 4 to 3 4 below the deck With the unit sitting on a flat level surface the front wheel position can be adjusted up or down as needed from 3 4 to 1 3 4 below the blade surface Move the front wheels up or down in 1 2 increments using the different axle mount holes in the roller mount bracket NOTE When the anti scalp rollers are installed the minimum cutting height is 1 1 2 with the anti scalp rollers set at 3 4 Pivot Front Wheels Refer to Figure 3 16 The front wheels can be set to pivot about the center of the mower frame to allow the front wheels to float with the contour of the ground or locked to prevent the wheels from floating Place the pins in the appropriate holes to obtain the desired functions gt ooo Wy A Pivot Locking Pins Figure 3 16 2 27 07 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 25 Table of Contents Section 4 Maintenance amp Lubrication Maintenance Locations 6 5 10 7 Engine Oil Fill amp Dipstick Fuel Filter Eng
33. ce Cutting Plane Straight Blade Comparison of Warped and Straight Blades Figure 4 15 Twisted Edge Replace R Cutting Edge Cutting Plane Original Edge Xx a v4 19075 e Straight Edge Blade Resharpening End View of Blades Twisted amp Straight Blades Figure 4 13 Figure 4 16 2 27 07 Z44 8 Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 35 Table of Contents Section 4 Maintenance amp Lubrication Land Pride Storage Take the following steps when storing the mower at the end of the season and when the unit will not be used for long periods to ensure readiness for the next mowing season IMPORTANT Do not use a high pressure washer on or around the IZT units Water intrusion will result and void the IZT warranty 1 Remove all grass dirt trash and grease that may have accumulated on the mower and moving parts 2 Scrape off compacted dirt trash and grass clippings from the deck underside A coating of oil may also be applied to the deck underside to minimize oxidation 3 Clean and touch up all scrapes with Land Pride spray paint 4 Check blades and blade bolts for wear and replace if necessary 5 Service air cleaner according to engine manufacture s recommendations 6 Check thoroughly for any worn or damaged parts that need replacing and order them from your nearest Land Pride Dealer 7 Thoroughly lubricate machine according to lubricat
34. ck height adjustment Pin for setting height and transport position Ignition switch throttle lever control levers blade engagement switch choke lever and Left Right Fuel Tank Valve Indicators Cup Holder Engine warning light and hour meter Two cup holders molded into the left side fuel tank Accommodates nearly any cup size including Big Gulp Cutting Heights Foot operated deck height adjustment Pin for setting height transport position Height adjustment in 1 4 increments from 1 1 2 to 4 1 2 Mowing Blades Heavy duty heat treated high lift steel blades 20 x 2 1 2 x 15 81 20 x 2 1 2 x 17 81 Blade Tip Speed Blade Drive 16 811 FPM 18 937 FPM V belt drive to all three spindles Spring tension idler pulleys Spindles Flotation Machine ductile housing 1 diameter high carbon steel shafts and greasable ball bearings Free floating mower using three blades with center blade to the front Mower is suspended at the four corners on spring assisted chains Includes 4 anti scalp wheels to improve flotation in rolling and uneven terrain 40 2448252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 6 Features and Benefits Table of Contents Z44 amp Z52 Accu Z Razor Features Ys 44 or 52 Cutting width Ground speed Sized and priced right for residential owners Forward 0 7 mph and Rev
35. d correct cause Store gasoline in an approved container and keep it out of children s reach Never buy more than a 30 day supply of gasoline Do not fill gasoline containers inside a vehicle on a truck or on a trailer Interior carpets and plastic truck bed liners insulate the container and slow loss of static charge When practical remove equipment from the truck or trailer and refuel the equipment with its wheels on the ground If this is not possible then refuel the equipment on the truck or trailer using a portable container and not a gasoline dispenser nozzle If a gasoline dispenser nozzle must be used keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete Gasoline is a poison harmful or fatal if swallowed Long term exposure to vapors can cause serious injury and illness Avoid prolonged breathing of vapors Keep face away from nozzle and gas tank opening e Keep gas away from eyes and skin The fuel tanks are located in the mower s fenders Total capacity for the fuel tanks is 12 U S gallon When filling the fuel tanks disengage blade engagement switch place control levers in park position set park to ON and stop engine Allow engine to cool before filling the tanks Clean dirt from around fuel tank cap remove cap and begin filling Do not fill fuel tanks to the top if mowing on hilly terrain or in hot weather Gas can rise up to the fuel cap vent
36. e and state of the art features Knowing the location and how these features work will make handling your mower more comfortable Below is a list of the major features we will be reviewing in this section 13 18 14 v Z 22 J Lon gt 5 D a Q z Ki A 5 Le S z o 5 6 N te C 0 ij e i 21 WS e Muffler Shield Is Located Under 2 the Engine 74 T T 18 7 19 20 2 3 4 Pr 13 8 10 23643 1 Blade Engagement Switch 9 Deck Height Indicator 17 Park Lever 2 Oil Pressure Light 10 Discharge Chute Guard 18 Fuel Tanks 3 Ignition Switch 11 Right Deck Cover Guard 19 Left Right Fuel Tank Valve 4 Hour Meter 12 Left Deck Cover Guard 20 Seat Platform Guard 5 Throttle Lever 13 Anti Scalp Wheels 21 Muffler Shield Guard 6 Choke Lever 14 Deck Adjusting Rod 22 Bypass Valve Rods 7 Battery Located under the seat 15 Floor Platform Guard 8 Control Levers 16 Deck Lift Pedal Razor Features Figure 2 1 10 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 2 Operating Procedures Table of Contents Operating Check List Hazard contro
37. eck support blocks under the deck edge in three locations a Place two of the 3 support blocks under the deck front edge in line with the far left and far right blade spindles b Center the third 3 support block under the deck back edge Blocking up Deck Figure 3 7 22 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Section 3 Adjustments Refer to Figure 3 8 5 Set cutting height at 3 1 4 on the height indicator by placing the height adjusting stop in the 3 hole and turning the height adjustment stop so that the flat side is against the stop handle 6 Clamp the height adjusting stop against the stop handle This will assure that the height will not move during the setting process Otherwise spring Pe 5 16 pressure from the deck lift springs will tend to pull the stop away from the handle 5 gt ju S ASIA 7 y i gt lt Figure 3 10 Figure se 8 Loosen the two nuts on the front of height indicator Refer to Figure 3 9 amp Figure 3 10 so that the foot pedal is free 7 On both sides of the mower loosen all nuts on the deck lift threaded rods and hardware on the adjuster until all deck lift chains are loose and the deck is sitting tightly on all three blocks Pigs Deck Lift A Threaded R O SS O Hb a AXN i Deck Level Adjustment Right Side Shown Deck Lift Rod Adjustmen
38. ement being towed with the hitch to come in contact with the mower or damage may result Electrical Cable Connection Refer to Figure 1 3 A WARNING Incorrect battery cable connections can damage mower s electrical system and cause battery cables to spark Sparks around a battery can result in a battery gas explosion and personal injury e Always disconnect negative black battery cable before disconnecting positive red cable e Always reconnect positive red battery cable to the positive post before reconnecting negative black cable to the negative post A WARNING Keep battery terminals from touching any metal mower parts when removing or installing the battery Do not allow metal tools to short between the battery terminals and metal mower parts Shorts caused by battery terminals or metal tools touching metal mower components can cause sparks Sparks can cause a battery gas explosion which will result in personal injury Black Negative Battery Cable lef E E EN Negative Y i Post Connecting the Negative Cable Figure 1 3 IMPORTANT The negative battery cable is disconnected before leaving the factory and is to be disconnected after initial dealer set up to prevent battery discharge while setting on the dealer lot Connect the black negative battery cable to the battery s negative post with 1 4 20 x 3 4 GR5 hex head serrated screw flat washer lock washer and nut before starting the mowe
39. engine is running Sweoo 838 308C Warning Rotating Blade Hazard FFAG ELITE Wee E SS WN 838 833C Warning Fuel Imbedded in Fuel Tank 2 27 07 Z44 8 Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 5 M Table of Contents Land Pride Important Safety Information serious burns REST HR A ble e Keep away from muffler 838 444C Danger Muffler Hot Both Sides of Engine To prevent serious injury or death g parts d wait for all moving parts to f os pida ayuda a alguien que ra que le lraduzca las medidas 838 310C AS o E 838 310C Warning General M A Zz oy n this is visi OT OP GLEMENT HAZARD can cause Serious Injury or Death Si no entiende ingles se prefiere que busque a alquien que interprete las instrucciones para usted PHDC 6 EH l j oh UE i he 818 543C ANG A 23643
40. engine running when servicing or making adjustments to the mower Place control levers in the neutral position disengage blade engagement shut engine off and remove ignition switch key 4 DANGER Repairs or maintenance specifically requiring engine power should be performed by trained personnel only Control levers should be set in park position with the park lever set to ON If the control levers are to be operated the tires should be properly supported off the floor Enclosed areas should be properly ventilated to prevent carbon monoxide poisoning Ay WARNING Before working on or under the deck make certain the engine cannot be accidentally started Shut engine off and remove ignition switch key for maximum safety Repairs or maintenance requiring engine power should be performed by trained personnel only A DANGER Exercise caution when working under the deck as the mower blades are extremely sharp Wearing gloves is advisable when working around or with the blades A WARNING When possible clean under mower using a stick or similar instrument making sure that no part of the body especially arms and hands are under mower IMPORTANT The arm rests on the Deluxe Seat must be pivoted up before hinging the seat platform forward Leaving the arm rests down while hinging the seat platform forward can cut the arm rest covers and void their warranty Regular maintenance is the best prevention for costly downtime or expe
41. erheat engine and hydraulic Pumps Blade P Engagement Ze lt Control Panel Figure 2 2 Choke Refer to Figure 2 2 A cable is linked from engine to choke knob to choke the engine during starting When choke control knob is down the choke is off engine running position When control knob is pulled up the choke is on engine starting position Shut choke off soon after engine has started IMPORTANT DO NOT operate mower with choke pulled up or on engine starting position 2 27 07 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 11 Table of Contents Section 2 Operating Procedures Land Pride Blade Engagement Switch Refer to Figure 2 2 The Blade engagement switch engages the deck blades Pull switch up to engage blades and push switch down to disengage the blades IMPORTANT Never engage blades with engine running at high rpm or when the deck is under load Clutch belts or deck could be damaged Left Right Fuel Tank Valve Refer to Figure 2 3 Located behind the seat on one side is the Left Right Fuel Tank Valve for controlling which fuel tank is in use The valve lever must be over one of the two arrows to supply fuel to the engine Arrows point to the fuel tank being used Switch valve from one tank to the other when tank in use is about out of fuel The mower does not have to be turned off to make the switch See Fuel System on
42. erse 0 5 mph for high mowing productivity Mid mount deck design Mid mount design puts the deck closer to the operator s line of sight for a more efficient and precise operation Compact size Drive tire stance Steering levers designed for more adjustment and comfort Stamped reinforcing ring added to deck construction Deck Construction Enhances mowing maneuverability as well as fitting on trailers or storing more efficiently Narrow width 44 44 52 45 allows for tight turns in corners yet gives a very stable platform for the operator Steering levers are designed with more adjustments to fit more comfortably to operators of all sizes Also new comfort grip handles are standard equipment Makes a stronger deck and reduces unwanted flex Single welded frame design 11 Gauge with 1 x 3 8 reinforcements Floating deck design Deck height adjustment Anti scalp rollers 4 Cutting height Deck has chain suspension which offers excellent flotation over uneven terrain Height is changed by a spring loaded foot operated lever and pin Easier than hand levers to push and faster than waiting on an electric actuation Front middle and front corners to keep scalping to a minimum 1 1 2 to 4 1 2 Range in 1 4 increments to cut any type of turf grass Tires High blade tip speed High lift blades 1 Blade spindles Wide tires offer excellent ground flotation Heavy wheel forks take abuse
43. etting directly controls blade speed The highest blade speed generally gives the best cut Select a mowing pattern that discharges cut grass away from uncut grass Generally this means using a pattern utilizing left turns because the mower discharges cut grass is to the right Refer to Figure 2 10 In any case avoid discharging cut grass onto an unmowed area because grass is then mowed twice Mowing twice puts an unnecessary load on the mower and reduces mowing efficiency Discharge Chute Discharge Chute Figure 2 10 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 17 Table of Contents Section 2 Operating Procedures Land Pride Mower Deck Operation A DANGER Never attempt to make any adjustments to the mower deck while the engine is running or when the blades are engaged Mower blades cannot be seen and are located very close to deck housing Fingers and toes can be cut off instantly With the engine running at a medium speed engage blades Refer to Figure 2 11 Advance engine throttle to full rom once the blades have become fully engaged NOTE Engaging the blades at high engine rpm or when under heavy load in tall grass for example can cause belts to slip resulting in premature wear or possible damage Engagement Switch Xi Blade Engagement Switch Figure 2 11 General Operating Information After thoroughly familiarizing yourself wi
44. g Radius Mowers Riding Mowers Accu Z Razor 357 044M 43 Table of Contents Section 8 Appendix Torque Values Chart Bolt Head Identific ation Bolt Head Identification Inches eae des daa Metric Class 5 8 Class 8 8 Class 10 9 in tpi N m ft lb N m ft lb N m ft lb mm x pitch N mi ft lb N m ft lb N m ft Ib 1 4 20 7 4 5 6 11 8 16 12 4 3 6 5 9 7 1 4 28 8 5 6 13 10 18 14 7 5 11 8 15 11 5 16 18 15 11 24 17 33 25 17 12 26 19 36 27 3 8 16 27 20 42 31 59 44 M10 X 1 5 J33 24 52 39 3 8 24 31 22 47 35 67 49 M10 X 0 75 39 29 61 45 7 16 14 43 32 67 49 95 70 M12 X 1 75 58 42 91 67 6 1 2 13 66 49 7 145 105 90 66 105 77 1 2 20 75 55 85 165 120 92 68 145 105 9 16 12 95 70 110 210 155 99 73 155 115 gi6 18 105 z9 165 120 Mi6x2 145 105 225 165 315 230 5 8 11 130 97 285 210 M16X1 5 155 115 240 180 325 240 M18X2 5 1195 145 310 230 510 375 M18X1 5 220 165 350 260 5 8 18 150 110 3 4 16 260 190 405 295 m20x2 5 280 205 440 325 610 450 3 4 10 235 170 225 165 820 605 650 480 250 185 905 670 760 560 340 250 1230 910 830 610 ar 12 370 275 955 705 1350 M30X3 5 oso 705 1510 1120 2100 1550 1 1 8 7 480 355 795 1750 1290 785 1240 2320 11 8 12 540 395 890 1960 1440 11 4 7 680 500 1120 2460 1820 1680 1270 2650 1950 3660 11 4 12 750 555 1680 1240 2730 2010 in tpi nomin
45. grene may result p 2 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual Prepare for Emergencies A Be prepared if a fire starts A Keep a first aid kit and fire extinguisher handy A Keep emergency numbers for doctor ambulance hospital and fire department near phone E Wear Protective Equipment A Protective clothing and equipment should be worn A Wear clothing and equipment appropriate for the job Avoid loose fitting clothing A Prolonged exposure to loud noise can cause hearing impairment or hearing loss Wear suitable hearing protection such as earmuffs or earplugs A Operating equipment safely requires the full attention of the operator Avoid wearing radio headphones while operating machinery Nak 2 27 07 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 3 Table of Contents Land Pride Important Safety Information Safety Labels Your mower comes equipped with all safety labels in place 4 Refer to this section for proper label placement They were designed to help you safely operate your implement To install new labels Read and follow their directions a Clean t
46. gure 2 2 Registers 1 10 hour increments up to 9 999 9 total hours The meter is connected to the ignition switch and records accumulative time only while the engine is running See Maintenance Schedule on page 27 Controls For general location of the controls described in this section refer to Figure 2 1 on page 10 and Figure 2 2 on page 11 A WARNING Do not operate mower while smoking IMPORTANT Prevent damage to the deluxe seat arm rests when hinging the seat platform Before hinging the seat platform up spread the control levers fully apart set the park lever to ON and pivot the seat arm rests up Ignition Switch Refer to Figure 2 2 A three position ignition switch off run and start is provided With key inserted rotate it clockwise to START position release key when engine starts and switch will automatically return to RUN position Turn key counterclockwise to OFF position to stop engine Throttle Refer to Figure 2 2 A cable is linked from engine to throttle for controlling engine speed Move throttle lever forward to increase engine rpm and rearward to decrease rpm Always travel and cut grass with throttle set at full engine rpm speed Slow down travel speed by pulling back on the control levers Slow engine rpm speed only if mower is not traveling or powering the cutting blades IMPORTANT Always operate throttle at full engine rpm while traveling or cutting grass Slow engine rpm may ov
47. he area the label is to be placed 1 Keep all safety labels clean and legible b Spray soapy water on the surface where the label is to 2 Replace all damaged or missing labels To order new be placed labels go to your nearest Land Pride dealer 3 Some new equipment installed during repair requires safety labels to be affixed to the replaced component as specified by Land Pride When ordering new components make sure the correct safety labels are included in the request c Peel backing from label Press firmly onto the surface Squeeze out air bubbles with the edge of a credit card 838 303C Danger Battery In Engine Compartment Beneath The Seat Mount 838 815C Warning Rollover Hazard WARNING Do not operate unless deflector is In place and in lowest pasition or complete grass collection system is in place 838 306C 838 306C Warning Do not operator without deflector 4 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Important Safety Information Warning Moving Parts MA f ARNI l ROTATING BLADE HAZARD e Keep Away Rotating Blades e To prevent serlous injury or death from thrown object o Do not operate with deflectors removed e Do not point discharge toward people animals or buildings when operating e Do not place hands or feet under deck when operating or when
48. iginal Sharpen only the top of the cutting edge to maintain sharpness Touch up sharpening can be done with a file r a jeans Ee T Resharpening Pattern Do not sharpen to original pattern below It is easier to get a straight cutting edge following the resharpening pattern shown above HORIZONTAL 19046 NAIL OR SHAFT Blade Balancing Figure 4 14 4 Balance of a blade is generally maintained by removing an equal amount of material from each end of the blade when sharpening Check blade balance by positioning the blade horizontally on a nail or shaft through the center hole See Figure 4 14 If either end of the blade rotates downward grind remove metal on that end until the blade will balance The blade is properly balanced when neither end drops If blade is out of balance true it up before reinstalling Refer to Figure 4 15 and Figure 4 16 Lay the blade on a flat surface and check for distortion Replace any distorted blade Do not re use spindle bolts which have stripped worn or undercut threads Refer to Torque Values Chart on page 44 when replacing hardware for proper torque A WARNING When mounting blades rotate them after installation to ensure blade tips do not touch each other or sides of the mower A WARNING Failure to correctly torque the bolt may result in the loss of the blade which can cause serious injury Warped Blade Repla
49. ine Air Cleaner Engine Oil Drain Plug Battery located under seat Fuel Tanks Gauge Wheel Bearing Zerk 2 Engine Oil Filter Deck Height Pivot Zerks 4 0 Safety Interlock Switch park located under seat 11 Drive Tire 12 Deck Belt 13 Pump Belt ap eee 14 Blades 15 Engine Air Intake Screen A eg 16 Front Gauge Wheel Tires E sN 17 Left Right Fuel Tank Valve 7 18 18 Floor Panel 4 1 17 19 Deck Lift Pivot Zerks 9 20 Front Axle Center Pivot Zerk 23643 located under floor panel 4 LO NO PUDO NN 16 20 Top View Honda Engine Shown Oil fill 8 dip stick 1 fuel filter 2 Oil filter 8 and fuel tank valve 17 are located on the left side for the Briggs amp Stratton engine 23687 Deck Bottom View Bottom View Drive motors removed for clarity Figure 4 1 26 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Section 4 Maintenance amp Lubricat
50. ion Maintenance Schedule Service at Intervals Indicated 25 Hours 50 Hours 100 Hours 200 Hours Page Clean mower Deck amp Engine Cooling System Verify Safety Start Interlock System Inspect Unit for loose hardware and damage Visually Inspect Tires Check Engine Oil Level Daily Before each use or every 4 hours whichever comes first Clean Air Intake Screen Daily Before each use or every 4 hours whichever comes first Check Fuel Level Daily Before each use Blades Sharp amp Securely Fastened Daily Before each use Discharge Chute Daily Before each use Securely In Place amp In Lowest Position Service Air Cleaner 6 Grease Blade Spindle Bearings Change Engine Oil amp Filter 1 fF Clean Cylinder And Head Fins fF Check Battery Connections fF Check Tire Pressure With A Gauge ee Clean Engine Exterior 3 fF Grease Deck Lift Pivot Points 8 fF Grease Front Azle Center Pivot 8 F Grease Gauge Wheel Bearings TI Check Pump And Deck Belt Tension 4 Check Fuel and Hydraulic Lines 5 Tighten Lug Nuts On Wheels 2 Replace Air Cleaner Paper Element Change Fuel Filter VI Replace Spark Plugs Change Transaxle Hydraulic oil 8 Filter 7 NOTES 1 Initial engine oil and oil filter change is after the first 5 hours of operation Thereafter change engine oil and oil filter every 50 hours of operation Change every 25 hours when operating the engine under dusty or dirty conditions heavy load high
51. ion instructions 8 Block mower up so weight is off tires NOTE Do not deflate tires 9 Protect battery from freezing temperatures Disconnect the negative ground wire from the battery to reduce the chances of a slow electrical drain Occasionally recharging battery during storage will extend battery life 10 Prepare engine for storage as described below 11 Store mower in a clean dry place Preparation of Engine for Storage When engine is to be unused for long periods proceed as follows 1 Run engine for a minimum of 15 minutes 2 Drain oil from crankcase while engine is still warm 3 Refill with fresh oil of proper viscosity 4 Drain fuel tank and run engine until it stops from lack of fuel Gasoline evaporates if left in carburetor for long periods forming gum and varnish deposits in carburetor These deposits will cause engine flooding and loss of power 5 Remove and replace fuel filter if not done in previous 100 hours 6 Remove spark plugs and pour a tablespoon of engine oil into each spark plug hole Install plugs but do not reconnect plug leads 7 Crank engine with starter at least a dozen revolutions to distribute oil over cylinder walls and valve mechanism 8 Clean exterior surface of engine Spread a light film of oil over any exposed metal surfaces of engine that are subject to corrosion 9 Clean dirt and chaff from cylinders and fins blower housing and muffler 10 Check oil filler c
52. k filter amp fittings For additional causes See engine manual Overheating Air intake screen or cleaning fins Clean screen and fin clogged Not operating engine at rated speed Increase engine speed to 3600 rpm Low oil pressure Low oil level Add oil Indicated by oil light on while engine is running Oil diluted or too light Change oil and check for source of contamination 42 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 7 Troubleshooting Table of Contents Symptoms High oil consumption Mower jerky when starting or operates in one direction only Hydraulic system operates hot Probable Causes Numerous Steering control linkage needs adjustment Suggested Remedies See your dealer Adjust linkage Hydro drive faulty Hydro drive faulty See your dealer See your dealer Not operating engine at rated speed Increase engine speed to 3600 rpm Mower creeps when steering control levers are in neutral Mower circles or veers in one direction Steering linkage needs adjustment Steering linkage needs adjustment Adjust linkage Adjust linkage Hydro drive faulty See your dealer Mower creeps with park lever engaged Steering linkage needs adjustment Adjust steering linkage and replace parking pawl 2 27 07 244 amp 252 S N 472620 526170 Zero Turnin
53. k the wheels to prevent the mower from rolling 16 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 2 Operating Procedures Table of Contents A DANGER Prior to operating the mower the operator should be thoroughly familiar with the proper use and operation of the equipment should read the manual completely and thoroughly and should have attempted slow moving maneuvers to become familiar with the operation of the equipment before attempting normal speed operation An inexperienced operator should not mow on slopes or on uneven terrain A WARNING Do not operate the mower while wearing any type of loose fitting clothing Always wear safety glasses clothing that does not hang loosely and shoes or boots when operating this machine A WARNING The tailpipe and muffler are very hot and can ignite dry grasses brush and other flammable materials Always keep the area around the muffler and tailpipe clear of debris Allow the muffler and tail pipe to cool completely before removing any debris to prevent sever burns to the body A WARNING Never direct discharge of material from mower deck towards bystanders A WARNING Never operate the mower deck with discharge chute removed or in raised position A WARNING Always check area to be mowed for rocks and other debris before mowing The mower s control levers are very responsive For
54. kage until the wheel comes to a stop c Repeat for the opposite side if necessary d When both wheels remain in neutral tighten jam nuts to lock pump linkage rod s in place Ball Stud y E mb O 4 nN U al O All H A O lA Re O j N al a JA l LBH 7 Dampener Spring Housing Steering Dampener Figure 3 3 20 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 3 Adjustments Table of Contents 3 Repeat step 2 to adjust the right dampener rod 4 Check steering dampeners a Move the control levers to reverse position and release The control levers should return to neutral position b Repeat steps 1 through 4 if control levers do not return to neutral position NOTE The dampener must not bottom out when the pump lever is fully stroked in either direction Seat Adjustment Refer to Figure 1 1 on page 8 IMPORTANT The arm rests on the Deluxe Seat must be pivoted up before hinging the seat platform forward Leaving the arm rests down while hinging the seat platform forward can cut the arm rest covers and void their
55. l and accident prevention are dependent upon awareness concern prudence and proper training involved in operation transport maintenance and storage of the riding mower Therefore it is absolutely essential that no one operates the mower without first having read fully understood and become totally familiar with the Operator s Manual Make sure the operator has paid particular attention to Important Safety Information pgs 1 to 6 e Section 1 Assembly amp Set up pg 8 e Section 2 Operating Procedures pgs 10 to 18 e Section 3 Adjustments pgs 19 to 25 e Section 4 Maintenance amp Lubrication pgs 26 to 38 Before beginning to operate your mower the following Operating Checklist should be performed Operating Checklist eference Page 1 Read Operating Procedures Pa Lubricate mower as needed Refer to Lubrication Pa Check mower safety start interlock system daily prior to operation Check mower initially and periodically for loose bolts amp pins Torque Values Chart Make sure all guards and shields are in place Check blade for nicks and sharpness Instrumentation Engine Oil Pressure Light Refer to to Figure 2 2 This light comes on when ignition switch is placed in RUN position and stays lit until the engine is running with a safe oil pressure Shut engine off immediately if light comes on during operation Locate and correct the problem Hour Meter Refer to Fi
56. led with wire clips The mower frame is banded to the crate floor 1 First remove the top panel by prying the wire clips free with a pry bar Then remove the side panels in the same way 2 Cut metal bands securing front wheels to the crate floor Discard bands Control Lever Assembly Refer to Figure 1 1 Control levers 1 are factory shipped rotated down and secured with plastic ties IMPORTANT Be careful not to cut the seat cover when removing packing material around the seat Cutting the seat cover will void its warranty 1 Being careful not cut control lever handles cut plastic ties securing the control levers 1 2 Rotate control levers 1 up until the bolt holes align Install bolts 3 and nuts 2 as shown 3 Align control lever handles with each other and tighten nuts 2 NOTE See Upper Control Lever Adjustments on page 21 for final adjustments to the control levers Seat Assembly Refer to Figure 1 1 1 The seat 4 is factory mounted to the hinged seat platform 5 Cut plastic ties securing the seat platform to the crate frame 2 Spread control levers 1 fully apart before attaching the seat platform 5 to the mower frame IMPORTANT The arm rests on the Deluxe Seat must be pivoted up when attaching the seat platform to the mower deck Leaving arm rests down while attaching the seat platform can cut the arm rest covers and void the warranty 3 Pivot the arm rest
57. ls and metal mower parts Shorts caused by battery terminals or metal tools touching metal mower components can cause sparks Sparks can cause a battery gas explosion which will result in personal injury A WARNING Do not overfill battery Electrolyte may overflow and damage paint wiring or structure When cleaning the battery use soap and water Be careful not to get soap and water into the battery Use soda mixed in water to clean corrosion off the terminals Common circuit problems are usually caused by electrical shorts corroded or dirty terminals loose connections defective wire insulation or broken wires Switches solenoids and ignition components may also fail causing a shorted or open circuit Refer to Figure 4 3 The electrical system is protected by fuses located along the wire harness beneath the seat next to the engine The fuses are e Main 20 Amp blade type e Clutch 10 Amp blade type Wiring Harness Fusses Figure 4 3 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 29 Table of Contents Section 4 Maintenance amp Lubrication Land Pride Refer to Figure 4 4 Remove the cover over the fuse to access the fuse 20amp Fuse W Cover Removed Figure 4 4 Before attempting any diagnosis of electrical system use a test light or voltmeter to check battery voltage If battery voltage is satisfactory check cleanliness and tightne
58. m ravelings with a sharp knife Inspect belt pulley grooves and flanges for wear A new belt or one in good condition should never run against the bottom of the groove Replace pulley when this is the case otherwise belt will lose power and slip excessively Never pry a belt onto a pulley as this will cut or damage the fibers of the belt covering Keep oil and grease away from belts and never use belt dressings Any of these will destroy the belt composition in a very short time 23652 Deck Belt Drive Layout Deck Belt Replacement Instructions Refer to Figure 4 10 1 Park mower on a flat surface Stop engine and remove ignition key Make sure blade engagement switch is in the down OFF position Spread control levers fully apart and set park to ON Disconnect negative battery cable 2 Place deck height in the lowest position 3 Remove the deck belt covers and floor panel 4 Release the deck belt tension by putting a 3 4 socket wrench on the over center release bolt 9 and turning counterclockwise This will relieve the tension on the deck belt idler spring 5 Pull tension idler 4 to the left of the machine to provide maximum belt clearance 6 Remove existing deck belt 1 Route new deck belt 1 as shown in Figure 4 10 8 Re tension deck belt idler 3 by turning the over center release bolt 9 clockwise Check belt tension per the Deck Drive Belt
59. m the rear verses the side The muffler is located to reduce potential burn hazard and to lower sound level at the operator s station Easily starts with the turn of a key Integrated fan blades Sleek styling twin six gallon molded fuel tanks with extra large inboard fuel caps Molded in dual cup holders and storage compartments Seat Options Pumps stay cool Twin six gallon tanks 12 gallons total with selector valve for extending operating range and decreasing down time Extra large fuel openings for easy fueling Inboard positioning of fuel caps so they don t come off during operation Cup holders fit a wide variety of cups and are in easy access to driver Storage compartments offer additional operator convince Molded seat incorporates a high back to give adequate comfort for the long jobs or Deluxe Cushion seat for additional suspension over rough terrain 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 41 Table of Contents Section 7 Troubleshooting Symptoms Probable Causes Suggested Remedies Starting motor does not crank Park lever is not in park position ON Place control handle in neutral and full or park switch is out of adjustment out pull up on park lever Re adjust park position switch Blade Engagement switch is engaged Disengage blade switch Weak or dead battery Recharge or replace For additional cau
60. me Deck All defects in the deck which results in the front edge of the deck being bent into the blades for the entire length of ownership by the original purchaser Engine 2 year limited warranty on Parts and Labor through engine manufacturer Battery 1 year limited warranty Belts blades and tires are considered wear items This Warranty is limited to the replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part and does not cover common wear items Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship This Warranty does not apply to any part or product which in Land Pride s judgment shall have been misused or damaged by accident or lack of normal maintenance or care or which has been repaired or altered in a way which adversely affects its performance or reliability or which has been used for a purpose for which the product is not designed Misuse also specifically includes failure to properly maintain oil levels grease points and other routine maintenance items Claims under this Warranty should be made to the dealer which originally sold the product and all warranty adjustments must be made through an authorized Land Pride dealer Land Pride reserves the right to make changes in materials or design of the product at any time without notice This Warranty shall not be interpreted to render L
61. mmon practices that may or may not be applicable to the products described in this manual Practice Safe Maintenance A Understand procedure before doing work Use proper tools and equipment refer to Operator s Manual for additional information A Work in a clean dry area A Put mower in park turn off engine and remove key before performing maintenance A Allow mower to cool completely before performing maintenance A Do not grease or oil mower while in operation A Inspect all parts Make sure parts are in good condition and installed properly A Remove buildup of grease oil or debris A Remove all tools and unused parts from mower before operation E a by Keep Riders Off Machinery A Riders obstruct the operator s view they could be struck by foreign objects or thrown from the machine A Never allow children under 16 years of age to operate equipment Avoid High Pressure Fluids Hazard A Escaping fluid under pressure can penetrate the skin causing serious injury A Avoid the hazard by relieving pressure before disconnecting hydraulic lines A Use a piece of paper or cardboard NOT BODY PARTS to check for suspected leaks A Wear protective gloves and safety glasses or goggles when working with hydraulic systems A If an accident occurs see a doctor immediately Any fluid injected into the skin must be surgically removed within a few hours or gan
62. movement of the control levers in either direction could result in a reaction that can cause serious injury Steering Refer to Figure 2 8 After starting engine engage the control levers and steer as follows e To Steer Straight While Traveling Forward Push control levers forward an equal distance e To Steer Straight While Backing Up Pull control levers rearward an equal distance To Turn Left While Traveling Forward Move right control lever farther forward from neutral than the left control lever e To Turn Left While Backing Up Move right control lever farther back from neutral than the left control lever e To Turn Right While Traveling Forward Move left control lever farther forward from neutral than the right control lever e To Turn Right While Backing Up Move left control lever farther back from neutral than the right control lever e To Make A Pivot Turn Move one control lever forward and the other control lever back of neutral this will allow the drive wheels to counter rotate 14 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 2 Operating Procedures Table of Contents Front of Mower Faces This Direction 7 CONTROL LEVERS OUT PARK LEVER UP ON NEUTRAL POSITION PARK LEVER ON PARK LEVER DOWN OFF CONTROL LEVERS IN at NEUTRAL POSITION PARK LEVER OFF i FORWARD
63. n transport maintenance and storage of equipment Be Aware of Signal Words A Signal word designates a degree or level of hazard seriousness The signal words are A DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury This signal word is limited to the most extreme situations typically for machine components that for functional purposes cannot be guarded dh WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed It may also be used to alert against unsafe practices A CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices For Your Protection A Thoroughly read and understand the Safety Label section read all instructions noted on them Shutdown and Storage A Lower machine to ground put mower in park turn off engine and remove the key A Detach and store implements in a area where children normally do not play Secure implement by using blocks and supports 2 27 07 244 8 Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 1 Table of Contents Important Safety Information Land Pride These are co
64. n and increase in speed as you pull further back If you push one lever forward and pull one lever back the mower will do a Zero turn in the direction of the control lever closest to your body Now take a few moments in a safe area to practice steering your mower with the engine still at half throttle Gradually increase your throttle speed until you feel totally confident in your mower steering and handling ability After removing all obstacles from the lawn it is now time to cut the grass With your mower at half throttle place your right foot on the deck lift pedal and release and lower the deck to your preset cutting height With your right hand pull up on the cutting blade engagement knob and increase the engine speed to full throttle You may now begin mowing When you are done mowing or just want to take a break make sure you e Park on level ground Disengage the cutting blades Throttle back e Move the control levers to wide open e Set the park lever to ON Turn the engine off e Remove the key e Step carefully off the front of the machine 18 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 3 Adjustments Table of Contents A WARNING Unless specifically required DO NOT have engine running when servicing or making adjustments to the mower Place control levers in the park position set the park lever to ON and
65. ng Mower with Stalled Engine on page 15 IMPORTANT Do not use a high pressure washer on or around the IZT units Water intrusion will result and void the IZT warranty Hydraulic oil and Filter Refer to Figure 4 6 Initially change hydraulic oil and oil filter after the first 50 hours of operation Thereafter change the hydraulic oil and oil filter every 200 hours or every 2 years whichever comes first Filter replacement kit 356 552A may be purchased from your nearest Land Pride dealer The Kit contains two filters and two magnetic plugs Change hydraulic oil and oil filter as follows 1 Raise mower so that filter and 9 16 magnetic plug can be accessed and worked on in a safe manner 2 Place oil pan beneath pump Access to Oil Filter and Magnetic Plug Figure 4 6 30 2448252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 4 Maintenance amp Lubrication Table of Contents 3 Clean the exterior of the unit of any debris before removing the oil filter and magnetic plug 4 Remove oil filter from underside of pump with 3 8 allen wrench and allow oil to drain completely IMPORTANT The filter is plastic excessive torque will damage filter 5 Torque bypass filter to 20 50 in lbs 2 6 Nm 6 Wipe off excess oil from case 7 Optional Replace 9 16 magnetic plug with newly supplied 9 16 magnetic plug 8 Lower mower s
66. ngage the park lever to ON to stop or slow the mower Control Levers With Handles Placed In Operating Position gt SS Control Levers Figure 2 4 23625 SE To Control Levers Spread Fully Apart Figure 2 5 Figure 2 6 12 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 2 Operating Procedures Deck Lift Pedal Refer to Figure 2 7 The deck lift pedal is used to raise and lower the deck and to set deck cutting height 1 Pushing on the deck lift pedal with your foot will raise the deck 2 Using the deck height indicator place deck height locking pin into the desired cutting height hole 3 Lower deck gently against locking pin When going over obstructions push the deck lift pedal to raise the deck Go around the obstruction if the deck will not raise high enough Never mow over obstructions you are not certain the deck will clear gt Figure 2 7 Safety Start Interlock System The mower is equipped with a safety start interlock system consisting of park switch seat switch and blade engagement switch Check mower safety start interlock system daily prior to operation This system is an important mower safety feature It should be repaired immediately if it malfunctions The machine incorporates a
67. nsive premature repair The following pages contain suggested maintenance information and schedules which the operator should follow on a routine basis Check initially and periodically for loose bolts and pins Torque loose bolts per the Torque Values Chart on page 44 Remain alert for unusual noises they could be signaling a problem Visually inspect the machine for any abnormal wear or damage A good time to detect potential problems is while performing scheduled maintenance service Correcting the problem as quickly as possible is the best insurance Clear away heavy build up of grease oil and dirt especially in the engine and under the seat platform minute dust particles are abrasive to close tolerance engine and hydraulic assemblies Inspect mower daily for grass clippings tangled wire and string The underside of the mower deck will collect a build up of grass clippings and dirt especially when grass is wet or has high moisture content This build up will harden restricting blade and air movement and will usually produce a poorer quality of cutting Therefore debris should be routinely removed from under the deck To do this it will be necessary to raise and block the deck in the full up position and scrape the build up from underneath Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel Consult your Land Pride dealer when assistance is needed Tor
68. od than the front Refer to Figure 3 10 on Page 23 26 Tighten A nut on both sides to jam it and B nut 14 Go to the right front of the mower tightly against the lift block 15 Loosen the 5 16 jam nut for the 5 16 adjuster bolt and then back the adjuster bolt out to allow the adjuster to move up and down freely 16 Be sure that the adjuster is free to move up and down Tighten the adjuster bolt until the chain just becomes tight Make sure the deck stays tight against the 3 block 17 Tighten the adjuster bolt jam nut to prevent the adjuster bolt from moving 18 Tighten the hardware holding the chain and adjuster onto the deck lift arm Refer to Figure 3 13 19 Go to the right rear of the mower 20 Make sure that there is still slack in the back right lift chain If not loosen the two nuts A amp B on the lift block until there is slack in the right rear deck lift chain 21 Tighten B nut until the chain just becomes tight making sure that the deck stays tight against the 3 Deck Lift Rod Adjustment Left Rear Side Shown block Figure 3 14 94 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 3 Adjustments Table of Contents Refer to Figure 3 12 on Page 24 27 Compress the deck lift assist springs so that there is 1 of space between the front nut and on the spring and the rear nu
69. on the Deluxe Seat up 4 Mount seat platform to the hinge tabs at the front with two 5 16 18 x 5 8 lg GR5 bolts 6 and two 5 16 flange hex locknuts 7 Tighten nuts snugly to remove all play and then back nuts up one quarter turn 5 Connect switch wires on the mower to the seat switch located under the seat 6 Hinge the seat platform down and secure in place with two 5 16 18 x 3 4 lg phillips head machine screws 8 7 The seat platform is slotted so the seat can be adjusted to fit the operator See Seat Adjustment on page 21 for positioning ee Rag OX mbly Standard Seat Assembly Shown Figure 1 1 Hitch Plate Assembly Refer to Figure 1 2 A hitch plate 1 is supplied with the mower and is shipped packaged with the manual 1 Remove two 5 16 18 x 5 8 GR5 hex flange screws 2 located under the bumper 2 Install hitch plate 1 as shown with existing 5 16 18 x 5 8 GR5 hex head flange screws 3 Tighten 5 16 hex head flange screws 2 to 17 ft lbs of torque Hitch Plate Assembly Figure 1 2 8 Z44 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 1 Assembly amp Set up Table of Contents IMPORTANT Do not pull a trailer or implement exceeding 300 pounds towing capacity and 50 pounds tongue weight Loss of control may result Do not make turns that will cause a trailer or impl
70. osition is made to the pump linkage rods located between the control lever and pump arms The pump linkage rods are properly adjusted when control levers are in neutral position and drive wheels are not turning Refer to Figure 3 2 If the mower creeps in neutral position adjust pump linkage rods located under the seat as follows 1 Raise and block mower up to support drive wheels off the floor Ay WARNING Make certain mower is secure when it is raised and placed on the jack stands The jack stands should not allow the mower to move when the engine is running and the drive wheels are rotating Use only certified jack stands 2 Position control levers in neutral position and disengage blades 3 Start engine and observe which way the wheels are 5 If wheel is rotating in reverse a Loosen jam nuts on pump linkage rod b Rotate rod to shorten steering control linkage until the wheel comes to a stop c Repeat for the opposite side if necessary d When both wheels remain in neutral tighten jam nuts to lock the pump linkage rod s in place 6 Test again by moving control levers forward and backward before returning them to neutral position The unit is ready for operation if the tires do not rot
71. page 31 for more information ZAR Left Right Fuel Tank Valve Center Position O as Shown is OFF Left Righ Figure 2 3 Control Levers Refer to Figure 2 4 and Figure 2 5 The control levers are used to steer accelerate brake and change direction Pulling the lever handles together and pushing forward from neutral position will move the mower forward Pushing one lever more than the other will turn the mower Pulling back on the levers from the neutral position will move the mower in reverse and pulling one lever back further than the other will turn the mower Use levers for braking by returning them to neutral See Driving the Mower on page 14 for a detailed description of operating the control levers Park Lever Refer to Figure 2 5 and Figure 2 6 A WARNING The park lever is not designed to hold the mower on steep slopes Both rear wheels are set in park when the park lever is engaged To place the mower in park set control levers in neutral spread control levers fully apart and set the park lever to ON The control levers will be locked in place and cannot be accidently bumped or pulled into power until the park lever is returned to the OFF position Always set park to ON before getting off the mower and always leave the park lever in the ON position until seated and ready to start traveling In the event of a system failure while mowing turn the switch key off move the control levers out and e
72. per leading lever back by the distance it was leading Tighten the locknuts to correct torque Example If the right control lever is one inch ahead of the left control lever stop the unit and either adjust the right upper control lever back one inch or adjust the left upper control lever forward one inch 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 21 Table of Contents Section 3 Adjustments Land Pride Hydro Drive Belt Adjustment The pump drive belt tension remains constant by means of a tension idler and spring There is no tension adjustment of this belt Deck Drive Belt Adjustment The spindle belt remains in constant tension by means of a spring tensioned idler The spring tension should be adjusted so that the belt does not slip under normal operating load conditions and may require readjusting as the belt stretches and wears The belt should be replaced if it is excessively worn or damaged Refer to Figure 3 5 and Figure 3 6 Check spring length to verify if belt is tensioned correctly Installed spring length should be 4 3 4 or 1 8 Vary the spring length by adjusting the length of the eye bolt A Eye Bolt Adjust Length To Vary Spring Tension YE SS Tension Idler Anchor Bracket AN SS lt KCC Drive Belt Adjustment Figure 3 5 Excessive belt tension may lead to premature damage of belt and drive components and is also
73. que Values WARNING Particular attention must be given to tightening the drive wheel lug nuts blade spindle bolts and electric clutch bolt Failure to correctly torque these items may result in the loss of a wheel blade or burnt clutch which can result in serious damage and or personal injury It is recommended that the lug nuts spindle bolts and electric clutch bolt be checked after the first 2 hours of initial operation and after removal for repair or replacement Thereafter they should be checked every 50 hours of operation See Torque valves in chart below For all other torques see Torque Values Chart on page 44 and engine manual for engine torque values Torque Values Wheel Lug Nuts Spindle Housing Flange Bolts Electric Clutch Bolt 68 74 50 to 55 28 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Section 4 Maintenance amp Lubrication Table of Contents Tires Use only tires recommended by Land Pride Solid fill tires are not to be used on the Razor mower Itis important for your safety and the safety of others that the tires have correct air pressure Check air pressure in all four tires before each use Visually inspect tires for loss of air throughout each day of operation See Tire Inflation Chart below for correct tire pressure Tire Inflation Chart Drive Wheels 8 12 Electrical System
74. r Tighten hex nut to 8 ft Ibs of torque Engine Preparations 1 Check engine oil level at the dipstick Add oil if oil is below the full mark on the dipstick Do not overfill Refer to engine manual for oil recommendation Also see Engine Oil and Oil Filter instructions on page 32 NOTE Vehicles are shipped from the factory with about a quart of fuel in the tank 2 See Fuel System instructions on page 31 before adding fuel Add fuel to the fuel tank Remove Mower From Crate Floor IMPORTANT Thoroughly read and understand Section 2 Operating Procedures pages 10 to 18 before starting and moving the mower 1 Make a ramp in front and level with the crate floor to be used for driving the mower off 2 Check under the mower to make sure itis not banded to the crate floor Remove any bands that are still present 3 Follow all precautions and operating information provided in Section 2 Operating Procedures before starting and driving the mower off 4 Raise deck fully up 5 Start the engine and drive the mower forward off the crate floor 6 Make necessary adjustments to the mower as outlined in Section 3 Adjustments beginning on page 19 2 27 07 Z44 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 9 Section 2 Operating Procedures Table of Contents Mower Features Refer to Figure 2 1 Your Razor riding mower is designed with innovativ
75. remove ignition switch key Repairs or maintenance requiring engine power should be performed by trained personnel only To prevent carbon monoxide poisoning be sure proper ventilation is available when engine must be operated in an enclosed area Read and observe safety warnings in front of manual Your Razor was adjusted before it left the factory and was checked during pre delivery set up However after start up and continued use a certain amount of break in wear will cause some adjustments to change Remain alert for unusual noises they could be signaling a problem Visually inspect the machine for any abnormal wear or damage A good time to detect potential problems is while performing scheduled maintenance service Correcting the problem as quickly as possible is the best insurance A WARNING Keep your machine clean Remove heavy trash deposits and clippings from the machine Keep all moving parts hydraulic system engine cooling system and exhaust system clean of trash and clippings Accumulation of trash and or clippings can cause fires hydraulic overheating and excessive belt wear Clear away heavy build up of grease oil and dirt especially in the area of oil fuel and engine combustion air minute dust particles are abrasive to close tolerance engine and hydraulic assemblies Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel Consult your Land Pride
76. rpose Grease Quantity As required 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 37 Table of Contents Land Pride Section 4 Maintenance amp Lubrication Gauge Wheel Bearing Zerk Located on hub of gauge wheel 2 Zerks One on each gauge wheel Type of Lubrication Multi purpose Grease Quantity As required NOTE Caster spindles have sealed bearings and require no servicing Front Axle Center Pivot Remove floor panel above deck to access 1 Zerk Type of Lubrication Multi purpose Grease Quantity As required 100 M H EA Hours Deck Lift Pivot Points 4 Zerks 2 left side and 2 right side Type of Lubrication Multi purpose Grease Quantity As required 38 244 amp Z52 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Table of Contents Section 5 Specifications amp Capacities Z44 amp Z52 Accu Z Razor Engine Specifications Engine Type gs Sion Horsepower 18 No of Cylinders Displacement 34 9 cu in 34 9 cu in 32 5 cu in 32 5 cu in 32 5 cu in 725 cc 725 cc 675cc 675cc 670cc Compression Ratio N A N A 8 3 1 8 3 1 8 3 1 Max Torque N A N A 32 5 FT LBS O 32 5 FT LBS O 32 5 FT LBS O 2500 RPM 2500 RPM 2500 RPM Oil Capacity w Filter 2 US quarts 2 US quarts 2 3 US quarts 2 3 US quarts 2 3 US quarts Oil Filter 831 053C
77. separate seat switch which will stop the mower engine when the operator is unseated for any reason while the mower is moving or the blades are engaged This is a safety feature designed to prevent runaway or accidental entanglement To inspect the system 4 The operator must be on the seat when testing the seat safety switch 5 Spread control levers fully apart and set the park lever to ON 6 Start mower engine per the instructions outlined in section on Engine Starting below Allow the engine to warm up to operating temperature 7 With the blade engagement switch down OFF and park lever set to ON slowly raise off of the seat The engine should continue to run Table of Contents 8 Set the park lever to OFF and slowly raise off the seat The engine should stop within five seconds 9 With the control levers spread fully apart and the park lever set to ON restart the engine 10 With the park lever set to ON and the engine running at a slow idle pull up on the blade engagement switch to turn the blades ON Slowly raise off of the seat The engine should stop within five seconds 11 Replace the seat safety switch if the switch failed to operate properly in any of the above steps and if no other cause such as damaged wiring can be determined 12 Contact your local Land Pride Dealer if the problem cannot be located Engine Starting The Razor safety start interlock system is also designed to protec
78. service center when assistance is needed Torque Values A WARNING Particular attention must be given to tightening the drive wheel lug nuts and blade spindle bolts Failure to correctly torque these items may result in the loss of a wheel or blade which can cause serious damage or personal injury Torque Values Wheel lug nuts 75 102 Blade bolts 135 183 It is recommended that the following be checked after the first 2 hours of initial operation and every 50 hours following removal for repair or replacement e Wheel lug nuts e Wheel motor nuts Blade bolts e For engine torque values see engine owner s manual Steering Linkage Refer to Figure 3 1 The steering has been factory adjusted to eliminate creeping when control levers are in neutral position However should the mower begin to creep adjustments can be made as outlined on the following page Neutral and arking Slot K G Control Lever In Neutral Position Figure 3 1 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 19 Table of Contents Section 3 Adjustments Land Pride Control Lever Neutral Adjustment Before considering any adjustment check tire air pressure and make certain hydraulic oil is at operating temperature Unequal tire pressure will cause mower to driftto one side Refer to Tire Inflation Chart on page 22 and page 44 Adjustments for neutral p
79. ses See engine manual Engine cranks but does not start No fuel or line plugged Fill tank or replace line Numerous See engine manual Left Hand Tank has gas Switch Left Right tank valve See Figure 4 8 on page 32 Engine Numerous See engine manual Runs with continuous misfiring or engine runs unevenly or erratically Grass cutting is ragged or uneven Dull bent or broken cutting blades Sharpen or replace cutting blades Deck full of wet sticky grass Clean underside of deck Cutting Blades are not operating at full Increase engine rpms to full speed engine speed 3600 rpm Belt over center take up is loose Tension over center take up Worn or broken belts Replace worn and broken belts Deck is not level Check air pressure in all 4 tires Make level adjustments to the deck Loss of power or system will not operate Bypass valve rods are disengaged Engage bypass valve rods in either direction Linkage bolt is loose or lost Replace linkage bolt Bad pump belt and or idler pulley Replace belt and or idler pulley Tighten idler pulley if loose Loose lost or broke idler pulley spring Reattach or replace idler pulley spring Restrictions in air cleaner Service air cleaner Internal interference or leakage in See your dealer Hydro Drive Insufficient hydraulic oil supply Have dealer check hydro drive Poor compression See your dealer Steering linkage needs adjustment Adjust linkage Air in system Chec
80. ss of terminals and ground connections A general understanding of electrical servicing and use of basic test equipment is necessary for troubleshooting and repair Major overhaul or repair of starting motor or alternator should be performed by trained technicians only Access to IZT Units Integrated Zero Turn Transaxle Refer to Refer to Figure 4 5 The IZT units are accessed by lifting the seat platform which is hinged at the front To raise it remove two bolts and tilt the seat platform up and forward NOTE If the seat is equipped with the optional arm rest kit make certain to place the control arms in the park position set park lever to ON and pivot the arm rests upward before tilting the seat platform Bolts 23643 Access to IZT Units Figure 4 5 WARNING Always wear adequate eye protection when servicing the hydraulic system and battery Hydraulic System The Razor is equipped with Hydro Gear IZT Integrated Zero Turn Transaxle units These units are self contained except for changing oil and filters Repair of an IZT unit should be performed by trained technicians only NOTE The IZT units are equipped with bypass valves For more information refer to Movi
81. stand the instructions given in this manual before operation Refer to the Safety Label section read all instructions noted on them Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment A Operator should be familiar with all functions of the unit A Operate implement from the driver s seat only A Do not leave equipment unattended with engine running A Dismounting from a moving mower could cause serious injury or death A Do not stand between the mower and implement during hitching A Keep hands feet and clothing away from power driven parts A Wear snug fitting clothing to avoid entanglement with moving parts A Watch out for wires trees etc when raising implement Make sure all persons are clear of working area A Turning mower too tight may cause implement to ride up on wheels This could result in injury or equipment damage Look For The Safety Alert Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken When you see this symbol be alert and carefully read the message that follows it In addition to design and configuration of equipment hazard control and accident prevention are dependent upon the awareness concern prudence and proper training of personnel involved in the operatio
82. t Left Side of Foot Pedal Shown Figure 3 9 Figure 3 11 2 27 07 244 8 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 23 Table of Contents Land Pride Section 3 Adjustments Refer to Figure 3 12 9 Start the leveling process on the left front side of the mower 10 Set the amount of threads on the deck lift rod to protrude approximately 1 pass the lift block 11 Jam both nuts against the lift block 12 Push or pull on the deck lift foot pedal until the chain on the left front just becomes tight making sure that the deck stays tight against the 3 block Deck Lift Assist Spring 1 Protrusion V j L eck Y DN Deck Lift Rod Adjustment Right Back Side Shown Z Lift Rod yo Figure 3 13 NI ANOS Refer to Figure 3 14 X 7 oA 22 Go to the left rear of the mower 23 Make sure that there is still slack in the chain If not Deck Lift Chain loosen the two nuts A amp B on the lift block until Deck Lift Rod Adjustment Left Front Side Shown there is slack in the left rear deck lift chain Figure 3 12 24 Tighten B nut until the chain just becomes tight ki hat th i i 7 Refer to Figure 3 11 ee sure that the deck stays tight against the 3 13 While keeping the left front chain tight tighten the pr nuts against the deck lift block on the height indicator or amen O A O mie re raise rear ofthe deck to be approximately 1 4 higher r
83. t Axle Center Pivot 38 Deck Lift Pivot Points 38 Section 5 Specifications amp Capacities 39 Section 6 Features and Benefits 41 Section 7 Troubleshooting 42 Section 8 Appendix 44 Torque Values Chart 00000 oo 44 Tire Inflation Chart 000 000 eee 44 Warranty 222 45 Land Pride provides this publication as is without warranty of any kind either expressed or implied While every precaution has been taken in the preparation of this manual Land Pride assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Land Pride reserves the right to revise and improve its products as it sees fit This publication describes the state of this product at the time of its publication and may not reflect the product in the future Land Pride is a registered trademark All other brands and product names are trademarks or registered trademarks of their respective holders Printed in the United States of America 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 2 27 07 Land Pride Important Safety Information Table of Contents These are common practices that may or may not be applicable to the products described in this manual Safety at All Times Thoroughly read and under
84. t on the deck lift block Typical both sides 28 When completed all chains will be tight and deck cutting height will be set to the deck height indicator Deck Cutting Height Adjustment Deck height is adjustable from 1 1 2 to 4 1 2 in 1 4 increments The holes in the height adjusting bar are spaced at 1 2 intervals By turning the height adjusting stop around 1 4 increments can be attained due to the 1 4 plate that is part of the stop Refer to Figure 3 8 EXAMPLES e When the height adjusting stop is placed in the 1 1 2 hole with the 1 4 plate facing to the front of the unit the cutting height is at 1 1 2 When the height adjusting stop is placed in the 1 1 2 hole with the 1 4 plate on the operator s side of the hole the cutting height is at 1 3 4 When the height adjusting stop is placed in one of the holes with the 1 4 plate on the operator s side of the hole the deck height will be set at one of the following 1 3 4 2 1 4 2 3 4 3 1 4 3 3 4 or 4 1 4 When the height adjusting stop is placed in one of the holes with the 1 4 plate facing to the front of the unit the deck height will be set at one of the following 1 1 2 2 2 1 2 3 3 1 2 or 4 The notch located at the rear of the right height adjusting bar 4 1 2 height is to used when the deck is placed in the transport mode Anti Scalp Rollers Refer to Figure 3 15 Anti s
85. t the operator and others from accidental injury due to unintentional engine starting The engine starting motor will not engage until e Park lever is in the up position ON e Blade engagement switch is in the down position OFF Ay WARNING Never leave the machine unattended with key in ignition switch NOTE The operator s seat is equipped with a separate safety switch The engine will stop if for any reason the operator should become unseated when the park lever is OFF or the blade engagement switch is ON The following steps are the correct procedures for starting the engine If difficulty is encountered contact the Land Pride Dealer in your area 1 Perform daily pre operation checks before starting the mower See Operating Check List on page 11 2 Make sure the control levers are in the park position park lever is ON and blade engagement switch is disengaged OFF 3 Set throttle at approximately 1 2 open position NOTE Use choke when engine is cold or if warm engine fails to start within 5 seconds of cranking Avoid flooding Operate the engine without choking as soon as possible 4 Insert key in ignition switch and rotate clockwise to engage starting motor Release key when engine starts 2 27 07 244 amp 252 S N 472620 526170 Zero Turning Radius Mowers Riding Mowers Accu Z Razor 357 044M 13 Table of Contents Section 2 Operating Procedures Land Pride N
86. th the Operator s Manual and completing the Operator s Checklist you are almost ready to begin mowing Approach the mower from the front Spread the control levers fully apart if they aren t already in the wide open position and set the park lever to ON Taking care not to step on either side of the mower deck step up on the operator s platform and comfortably seat yourself With both control levers still wide apart reach for the throttle and choke control to your right side Position the throttle control at half throttle and pull the choke to the up on position Insert your ignition key and rotate the ignition key clockwise until you hear the engine begin to start Release the ignition key and push the choke to down off position Allow the engine to warm up momentarily If your mower has just been running and the engine is already warm using the choke is usually not necessary With the engine at half throttle set the park lever in the OFF position and pull the control levers in to bring both control levers equally together in the neutral position just in front of you It s now time to test your steering skills Gently push both control levers equally forward The farther forward you push the levers the faster you will go Pull back equally and you will slow down coming to a stop when you reach the neutral position Now slowly pull the levers back toward your body past neutral position The mower will reverse directio
87. trol may result Do not make turns so sharp as to cause trailer or implement being towed to come in contact with the mower Damage may result A Do not attach an implement trailer or other device to the hitch that will produce negative tongue weight A Do not tow the mower with its wheels on the ground Always tow the mower loaded on a trailer A Use extreme caution when cresting hills or when visibility is limited Proceed slowly until you are sure trail conditions immediately ahead are safe A Reduce speed on hilly rough wet slick or unstable ground Do not operate mower on slopes over 15 A Do not operate the mower at night With poor visibility night operation can lead to a serious accident A When refueling use a UL listed container that has a screen or filter Set container on the ground before fueling to eliminate static discharge and do not use Methanol fuel A Do not smoke or use electrical devices including cell phones while refueling A Always maintain proper tire inflation See Tires on page 29 A Always disconnect the negative battery terminal before making adjustments to the mower electrical system or welding on this mower A Always check wheel lug nut torque values two hours after initial operation and two hours after each tire repair and or replacement Routinely check lug nut torque valves every 100 hours of operation See Torque Values on page 19 A Support this mower securely before working beneath Choc
88. ts Manual contact your authorized dealer Manuals can also be downloaded free of charge from our website at www landpride com or printed from the Land Pride Service amp Support Center by your dealer Terminology Right or Left as used in this manual is determined by facing forward while sitting in the operator seat unless otherwise stated Definitions NOTE A special point of information that the operator must be aware of before continuing IMPORTANT A special point of information related to its preceding topic Land Pride s intention is that this information should be read and noted before continuing Owner Assistance The Warranty Registration card should be filled out by the dealer at the time of purchase This information is necessary to provide you with quality customer service If customer service or repair parts are required contact a Land Pride dealer A dealer has trained personnel repair parts and equipment needed to service the mower The parts on your mower have been specially designed and should only be replaced with genuine Land Pride parts Therefore should your mower require replacement parts go to your Land Pride Dealer For parts and service to your mower engine contact your nearest engine dealer or call Customer Service Hotline provided below Service Manual Honda 18 HP P N GXV610K1 Honda 20 HP P N GXV620K1 B amp S 20 HP 273521 5 99 B amp S 25 HP 273521 5 99 Owner s
89. tween the belt and the pulley when the pulley is released and tension is re established 15 Re install the deck drive belt on the electric clutch pulley and make sure it is routed properly on all of the deck pulleys 16 Reattach clutch restraint bracket 9 with two 1 4 20 GR5 hex flange head screws and hex flange nuts 10 Tighten nuts to correct torque 17 Re tension the deck belt idler per the Deck Belt Replacement Instructions on page 33 18 Re attach the negative battery cable Mower Blade Maintenance Blade Inspection Check the mower blades daily they are the key to power efficiency and well groomed turf Keep them sharp a dull blade will tear rather than cut the grass leaving a brown ragged top on the grass within a few hours A dull blade also requires more power from the engine Replace any blade which is bent cracked or broken 4 WARNING DO NOT try to straighten a blade that is bent Never weld a broken or cracked blade ALWAYS replace with a new Land Pride blade to assure safety A DANGER Never work with blades while engine is running or blade is engaged Always place blade engagement switch in the down Off position place both control levers in neutral position place park lever in ON position and turn engine off Block up mower when you must work under it Wear gloves when handling blades Always check for blade damage if mower strikes rock branch or other foreign object during mowing

Land Pride 357-044M Lawn Mower User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents