Kuppersbusch USA KGCT 907.2E Cooktop User Manual
Contents
1. If the moving part of the cooking area is blocked during extension or retraction a force dependent safety cut out responds and interrupts the travel operati on If the blockage lasts a lengthy period the moving part no longer moves back into the end position In this case press the buttons Y and ZX to move the moving part of the cooking area back into its end position KGCT 907 2E You have 9 cooking settings available Select the required cooking setting with the plus or minus sensor It will be indicated in the display The pan detection function must either be deactivated or a pan that is suitable for detection by the pan detection function must have been placed on the cooking zone in order to be able to select a setting for the cooking zone LILI OW The 0 position is visible for about 2 seconds after the appliance switches off Cooking setting Suitable for 1 3 Heating warming creeing defrosting 4 5 Steaming poaching boiling 6 8 roasting deep frying 9 Heating large quantities When pressing the plus sensor the cooking zone starts at cooking set ting 5 without boost When pressing the minus sensor the cooking zone starts at cooking setting 9 This automatically starts the auto matic boost Switching off the cooking zone Press the plus and minus sensor at the same time LILI IW IR If the sensor of a rear cooking zone A O is touched when the cooking ar2. itself off switching off the pan recognition function put onto the cooking zone an un e g when using glass pans or other pans that are unsuitable for use with the saucepan sensor UNC ai O Press the plus and minus sensor at the same time before making the cooking setting LI LIW A circle will appear in the display LI O O next to the selected cooking set LIT There is a defect in the pan re cognition function if this circle li ghts up You can nevertheless continue to use the cooking zone O OR a EJE The automatic pan size sensor of the dual circuit zone The dual circuit zone has a sensor to detect the size of the pan being used When a small pan is placed on the cooking zone only the inner ring will switch on If the entire zone is covered by the pan both rings will switch on Please note that the outer ring must always be completely covered even if you are using pans with a rounded base Moving the pan during cooking can cause the outer ring to switch off if it has KGCT 907 2E not been completely covered 9 rn Y ce The outer cooking zone circuit can also be switched on and off when the pan detection function is active Some instructions on cookware Only use pans with even and flat bottoms ment Rough pan bottoms scratch the glass ceramic area when shifted Uneven pan bottoms prolong the boost about When using fireproof glas
3. 30 V 3 safety current 16 A Connection cable Use H 05 RR F or H 07 RN F Length of cable as necessary Connection data When assembling the connecting box remember that it must be at least 300 mm from the floor as shown in the drawing Single phase connection 230 V phase against neutral conductor Cable to the hob Supply line from cooker junktion box min 300 The conductor colours may be different The connection diagram and the terminal numbers are the decisive factors Ges Ces baa Fees A Three phase connection 400 V system with 230 V phase against neu tral conductor KGCT 907 2E
4. BEDIENUNGSANWEISUNG mit Montageanweisungen Instructions for use and installation instructions CF Instructions d utilisation et avis de montage WD Gebruiksaanwijzing en montagehandleiding CD Istruzioni di uso e di montaggio CE gt Instrucciones de uso y de montaje CP gt Instru es de uso e de montagem OAHTIEZ XPH2H2 KAI Z YNAPMOAOTHZH2 OO OO KGCT 907 2E K ppersbusch 072594 L41 For your information Please read the instructions in this booklet carefully as it contains important information concerning the safety the installation the use and the mainte nance of your appliance The appliance should only be used for cooking in the household Keep the operation instructions in a safe place Notes on disposal Disposing of the packaging The transport packaging consists of the following materials Corrugated card board cardboard styrofoam CFC free Polyethylen foil Do not put these materials in the household rubbish but ask your local au thority to give you the adress of the most convenient collection point What to do if you happen to have an old appliance Old appliances contain many materials which can be recycled For this reason you should not simply put your old appliance on the rubbish tip but ask your local authority how it might be recycled Conditions of guarantee The conditions of guarantee applicable for this product are subject to those published by the representative in the relevant coun
5. Watt 2 Extend retract sensor buttons cooking area Ag Y 180 mm 1800 Watt 180 mm 1800 Watt O00 3 Sensor buttons grill area NR 140 mm 1200 Watt 4 Sensor cooking zones 9 Safety strip oF IES 10 Grill area 6 On sensor Stand by switch ca ca 440 x 200 mm 1960 Watt KGCT 907 2E 15 Safety instructions for connection and function m The mains connection maintenance and repair jobs should only be carried out by an authorised technician in accordance with the applicable safety standards Work which has been improperly carried out can endanger your safety m The surfaces of heating and cooking zones become hot during operation The cooking area is moved by a motor Therefore Always keep children away for the cooking zones and the grill area m Overheated fats and oils may spontaneously ignite You should therefore cook food involving the use of fats and oils e g chipped potatoes only un der supervision Never extinguish fats or oils with water Place a lid on the pan switch off the cooking zone and take the pan off the hot cooking zone m f cracks fractures or any other defects appear in your glass ceramic coo king area do not use your appliance Unplug or otherwise disconnect your appliance from the mains supply and call our service centre m f the cooking area cannot be switched off due to a defect in the sensor control immediately disconnect your appliance and call the service centre m Be caref
6. ea em a aS is retracted the symbol ap pears in the display and an acou LIL stic signal is emitted a The automatic boost function All cooking zones are equipped with an automatic boost function Maximum power is used for the boost The time period of the boost depends on the selected cooking setting After the elapsed time the cooking zone automatically switches back to the selected cooking setting ce The automatic cooking function will be deactivated if the pan detection function is activated and the pan is taken off the cooking zone The au tomatic cooking function will continue to operate once the pan has been put back onto the cooking zone When selecting the respective coo king setting by pressing the minus sensor the boost function swit ches on automatically E OCILI During automatic operation a A lights up in the display alternately with the selected cooking setting When selecting the required coo king setting by pressing the plus sensor it is necessary to press the plus sensor again after reaching cooking setting 9 if the automatic boost function is to be activated Select the required cooking set ting A A MO IOO A lights up in the display alterna z tely with the selected cooking set ting A Cooking zone heating indicator Old As long as the cooking zone is still CS hot an H will appear in the dis play when the cooking zone has T been switched of
7. f Dual circuit cooking zones Usually the cooking zone with the smaller diameter is being heated Switch on the outer cooking zone circuit for bigger sauce pans Press the cooking zone symbol next to the plus minus sensor The light on the left below the symbol for the dual circuit cooking zone indicates that the cooking zone has been activated OIL ML Pressing the cooking zone symbol once again deactivates the dual circuit cooking zone The grill area The setting of the grill area you want can be selected with the plus or the minus sensor Preheat the grill area for about 5 minutes at setting 9 Grill the food on each side at setting 9 for 1 2 minutes then turn down and finish the grilling pro cess The grill area can also be used as an area for keeping food warm at setting1 In this case do not apply oil to the grill area The pan recognition function All cooking zones have a saucepan sensor The dual circuit zone is also able to detect the saucepan size ce The pan detection function detects all pans made of metal The pan detection function must be deactivated in order to use cooking equipment made of glass or ceramics DW 8 WO CH EJE If a suitable pan is put onto the cooking zone U is indicated by the display KGCT 907 2E If no pan or an unsuitable pan is CMC 200 derlined U is indicated After 1 minutes the cooking zone auto matically switches
8. irect contact with food We recommend you to rub down the grill surface with half a lemon or lemon juice Any slight dirt marks from protein e g from meat is removed and the grill surface shines again KGCT 907 2E What to do if there is a fault La Unplug the appliance befor repair Check carefully to make sure that the fault is not due to misoperation You can rectify many faults yourself Important note Repairs should only be carried out by an authorised technician Even during the guarantee period repairs will not be free of charge if due to incorrect ope ration or to non adherence to our instructions given under What to do if there is a fault Fault Cause Remedy Circulating dash symbols on all 4 LED displays No faults normal display after power interruption If no objects have been lying on or obstructing the sensors con firm this by pressing the Off sensor Horizontal dashes that are shown on the display running from top to bottom Failure of electronic component Switch off cooker fuse in fuse box Call service centre Not possible to switch off cooking area Failure of electronic component Switch off cooker fuse in fuse box Call service centre Cooking area cannot be retracted or extended Safety cut out after too frequent retrac tion and extension of the cooking area owing to risk of motor overheating Wait until duration of safety cu
9. itchen wall behind the built in furniture If there is no built in oven below the hob the connecting box can also be fa stened to the furniture below the hob m When assembling the connecting box remember that it must be at least 300 mm from the floor as shown in the drawing m The connecting box must not come into contact with any hot appliance parts m The connecting box must not be used as a voltage distributor for other appliances m The appliance is connected to the mains at the connecting box as shown in the wiring diagram The connection may only be made in the connector box m The connector box must not be removed m The fitted connection cable must be replaced by the K PPERSBUSCH Cu stomer Service if it becomes damaged m The green yellow earth conductor must be longer than the other wires Connection diagram PE L1 230 V_ 230 V 230 V ol3No o o o o PE L4 L2 L3 N 230 V 230 V 230 V Caution Incorrect connection results in the total destruction of the power electronics 24 Electrical Permanent connection by means of an oven connection connection socket Connection is depicted on the underside of the appliance suitable for diagram the various types of mains Permanent connection 400 V 3 N 50 Hz AC 230 V in UK Voltage of heating element 230 V Total connection output 10 4 kW 400 V 3 N safety current 16 A 400 V 2 N safety current 20 A 230 V 1 N safety current 25 A 2
10. lling onto your cooking area might break it m Please read through the cleaning and care instructions Be especially careful to keep the sensor keys clean since soiling could be mistaken for finger contact by the appliance Never put anything pans tea towels etc onto the sensor keys If food boils over onto the sensor keys we advice you to activate the emergency switch m You might hear a humming sound from the heating when switching on the appliance This is due to technical reasons and has no influence on quality and functioning of your appliance m Hot pans should not cover the the sensor keys otherwise the appliance switches itself off automatically Use of the cooking zones and the grill area A Read the safety instructions After initial connection and after a power failure the abbreviations C A L ap pears briefly in the LED displays Then rotating circles are displayed This me ans that the sensors are being checked in a self test and at the same time the button sensitivity reset Acknowledge this display by touching the Off sensor Provided that no objects are lying on he sensors these symbols are switched off immediately Other wise remove objects switch off lighting if on and disconnect the cooking zone again briefly from the mains fuse Important There must be no objects on the sensors while the sensor sensitivity is being set Extreme lighting shining on the buttons such as direct sunlight or bright hal
11. n sensor is switched off You should always give the data on the rating plate to your service centre in case you have enquiries or want to order spare parts The rating plate is lo cated underneath the cooking area The rating label is located at the bottom side of the hob It is also stuck onto the cover page of this operating manual 22 KGCT 907 2E Installation Installation in a fitted kitchen m Be careful during fitting Do not put or drop edged or pointed tools screwdriver etc on the glass top m Any cooker hoods or wal least 650 mm from the h m The appliance must be in m The K ppersbusch built in the zoom cooking centre cupboards must have a vertical clearance of at ob unit stalled absolutely horizontally oven EEB 9800 9600 can be fitted underneath KGCT 907 2E The cooker is Y type design providing overheating protection for surrounding surfaces fitted cupboard components That means that this appliance can be placed with its back wall and one side wall next to cupboard or room walls of any height The other side wall may only be placed next to a fitted cupboard of the same height at the most The plastic coating or veneer must be applied with a heat resistant adhesive 100 C This adhesive prevents the surfaces from warping or working loose Have you connected the mains lead with the appliance Using 4 2 x16 mm screws install the supporting rails in horizontal po
12. ogen lights is to be avoided switch on the cooking area and the grill area Press the sensor button for ap prox 2 seconds The LED display above the sensor lights up and the appliance is in operation stand by mode The stand by mode automatically switches itself off if no cooking zone is activated within 20 minutes after 10 seconds an acustic signal indicates that the appliance switches itself off after another 10 seconds or if the appliance is not used 1 minute after starting operation KGCT 907 2E Extending and retracting cooking area The cooking setting The cooking area cannot be extended and retracted unless the appliance is switched on If you touch the button Y the coo king area is extended The rear cooking zones can only be used in the fully extended condition If you touch the button ZA the coo king area is retracted if the button ZA is pressed when the cooking area is switched on an acoustic signal is emitted The cooking area cannot be retracted if the rear cooking zones are switched on if the retraction function is interrupted by the safety strip being pressed slightly to the rear e g by kitchenware Caution If the cooking area is retracted and extended consecutively very fre quently a safety cut out facility is activated This prevents the motor from overheating The moving part of the cooking area can no longer be retracted or extended for a brief period
13. s or times and increase the power require porcelain cookware please follow the manufacturers instructions Choose a pan with a diameter at least as large as the cooking zone heating of the cooking area You will save a lot of energy by coo K pE nes you can precisely set the king in a closed pan Liquids and temperature required With a little practice you will readily make the correct You will thereby save energy and coo X yr foods will only boil over if the tempe choice of cooking settings so that nothing boils over even when a lid is in king time You will also avoid over Wherever possible place a lid on the pan rature is too high For the cooking zo place The rapid switch off function All the cooking zones can be swit ched off quickly with the OFF sen sor Child proof lock sensor lock Time limit function holiday function Operating the sensor lock detains unauthorised persons from using the ap pliance In order to activate this lock the cooking area has to be in operation Activating child proof lock Press the sensor lock 2 seconds The child proof lock can be activa ted if the cooking area is in opera tion In this case you can only choose a lower cooking setting or switch off The lock is indicated by 3 flashing control indicators Goat 809 8003 8 a OG OO Ot O Be careful Switching off the cooking area does not deactivate the lock Ol Deac
14. sition on the right and on the left onto the cupboard sides according to measu rements Fit in the appliance Fasten the appliance onto the supporting rails using 4 2 x 7 mm srews Seal the appliance on the back and on the two sides with silicon 23 Electrical connection m The built in cooking area must be connected to the mains supply by a qualified electrician who is authorized to carry out such work m Both legal wiring regulations and the requirements of your local electricity supply board must be fully complied with m When connecting the hob a device must be provided which enables all pole disconnection of the hob from the supply with a gap construction of at least 3 mm Circuit breakers fuses and contactors are considered to be suitable disconnecting units m When connecting and repairing the appliance disconnect it from the elec tricity supply with one of these devices m Overall protection against electric shock must be ensured by the installation m The earthed conductor lead must be sufficiently long so that in the event of failure of the strain relief it is not subjected to strain until after the live wires of the connection cable m Any superfluous cable must be removed from the installation area beneath the appliance At the factory the electronic hob has been equipped with a temperature proof cable with a connecting box for the oven connection cable The connecting box is fastened to the k
15. t out has expired Cooking area cannot be retracted Safety strip pressed in safety cut out has been activated Remove obstacle preventing retraction of the cooking area Rear cooking zones cannot be switched on Cooking area not fully extended Extend cooking area fully The LED indicator for the cooking level or heat indicator does not light up or only partly lights up LED indicator defec tive Call Customer Service There is a danger of being burned as the temperature warning is not reliable Cooking area does not heat Fuse is defective Check or replace cooker fuse in fuse box Child proof lock activated Deactivate child proof lock Cooking area is defective Call service centre Inner circuit of the dual circuit zone is defective Do not operate the functioning outer circle Immediately call service centre Individual all sen sors do not react to touch Disconnect the hob from the mains via the fuses Individual all sen sors do not react to touch Sudden change in heat radiation Remove the source of heat Electronic circuits have experienced slight movement due to impact Disconnect the hob from the mains via the fuses 21 CH D CT When this point flashes it indicates Ch JI Le that the saucepan sensor is defec tive However you can continue to L T use the cooking zone when the saucepa
16. tivating the child proof lock at once after max 3 Sek HAD 8 HB Oui Old DO Old Ol EQ Press the sensors under the two left flasing control indicators at once After not more than 3 seconds press the sensor under the flashing control indicator on the right Note When the power supply has been interrupted the child proof lock is no longer active 20 The appliance is equipped with an automatic time limit function This function makes sure that the appliance is not in operation for a long time The time period of the time limit depends on the selected cooking setting eg The hig her the selected cooking setting the faster the appliance is switched off Cooking setting Switching off time after 2 hours 4 hours 5 hours 9 8 7 6 5 3 hours 4 3 2 1 10 hours The function to limit operation time works separately for each cooking zone Other functions m pressing two or more sensor keys at the same time e g when a pan is mistakenly put onto the sensor key no function is activated An audible signal sounds after 10 seconds The appliance switches off automatically after 20 seconds Exceptions Deactivation of the child proof lock Switching off the cooking zones m f you continue to press a sensor button even after having set the highest cooking setting an audible signal sounds after 10 seconds After 20 se conds the appliance switches off automaticall
17. try Details regarding same may be obtained from the dealer from whom the appliance was purchased For claims under guarantee the sales receipt must be produced Contents Your appliance at a glance cece eee 15 Safety instructions o oooooooooomoooo 16 for connection and function for the cooking zones and the grill area Before first use 2 1 1 ees 16 Use of the cooking zones and the grill area 16 Switch on the cooking area and the grill area Extending and retracting cooking area The cooking setting The automatic boost function Cooking zone heating indicator Dual circuit cooking zones The grill area The pan recognition function Switching off the pan recognition function The automatic pan size sensor of the dual circuit zone Some instructions on cookware The rapid switch off function Child proof lock sensor lock Time limit function holiday function Other functions Cleaning and care 21 What to do if there is a fault 21 Installation 0 ce ee ee 23 Installation in a fitted kitchen Electrical connection KGCT 907 2E Your appliance at a glance K ppersbusch ZOOM L ah om ob ob oom OO 00 000 00 Ow 00 CC VA e 1 2 3 4 567 1 Dual circuit cooking zone 7 Sensor child proof lock sensor lock will Y 230 mm 2300 Watt 140 mm 1000 Watt 8 Cooking zones ua 140 mm 1200
18. ul when working with additional appliances The connection leads must not come into contact with the hot cooking zones m The glass ceramic cooking area should not be used as a storage area m Do not place combustible or inflammable objects upon the cooking top which might be dangerous in case of unintentional switching on m Never use the cooking zones without cookware Never use the appliance to heat rooms m Never put aluminium foil or plastic on top of the cooking zones Substances that melt for example plastic foils and especially sugar and food with a high sugar content are to be kept away from the hot cooking zone In order to avoid damaging sugar while still hot should immediately be scraped off the cooking area with a scraper m Avoid repeated burning of stains and boiling over m Chalk deposits may damage the cooking area m The appliance is equipped with a safety cut out facility It ensures that the cooking area cannot be retracted if an obstacle hits against the safety strip and presses it in m f you have pets in your flat who might reach the cooking top activate the child proof unit A Before first use Remove packaging and moving parts Before first use the cooking area should be cleaned with a damp cloth and a little washing up liquid The cooking area is insensitive to temperature shocks cold and hot and also extremely robust m Avoid dropping sharp objects onto the cooking area Pointed objects fa
19. y m In case of a break down of the mains supply the appliance does not auto matically switch on again If the child proof lock was activated before the power failure this is now deactivated m f the electronics overheat the hob will switch off All 4 LED indicators will flash and a cyclical signal will be heard KGCT 907 2E Cleaning and care m Never use sharp or abrasive agents It is sufficient to clean with a damp cloth and a little washing up liquid after usage Wipe dry m Incrustation due to boilied over foods are best presoftened with a wet cloth Then remove them with a glass scraper Sugar and melted plastic should be removed while the cooking area is still hot m Clean the glass ceramic cooking area after every use Always keep the sen sor keys clean since soiling could be detected as finger contact by the aplliance Immediately remove soiling Never put anything pans tea towels etc on the sensor keys If food boils over onto the sensor buttons we ad vise you to activate the emergency switch m Care for your glass ceramic cooking area once a week Regular care builds up a protective layer and also eases day to day cleaning Please follow the instructions of the cleaner or cleanser man ufacturer concerned Even heavy soiling can be cleaned with a cleanser and enough water Wipe dry with a cloth m Do not use the cleaning agent on the gril surface as the protective film would come into d
Download Pdf Manuals
Related Search