Kuppersbusch USA EKWE Cooktop User Manual
Contents
1. All of the cooking zones can be switched off quickly with the ON OFF sensor Minute minder and switch off function Adjusting the minute minder The minute minder operates as a switch off and as a reminder for a maximum of 99 minutes The time is set in minutes The minute minder also operates if the control honeycomb has been switched off Touch the plus sensor lightly to switch on the minute minder The display will show 0 Set the required time by touching the plus sensor again if necessary for longer The time set can be reduced again by touching the minus sensor When the time set has elapsed O will flash in the display and an acoustic signal will sound If you wish to stop the acoustic signal press one of the clock sensors Should you wish to switch the minute minder off before the time has elapsed touch the plus and minus sensors of the clock simultaneously setting the switch off function for a cooking zone The switch off function can be used to switch a cooking zone off after a required period of time The switch off is a function of the minute minder and can only be activated if a cooking zone has also been activated Set a power level for the cooking zone selected Set the minute minder to the time required Now touch the clock sensor and the plus sensor of the selected cooking zone simult2. nnnnenenmeanenmanennnnnenmanmeaman manna 15 3 Safety instructions The cooktop must be built into a countertop opening Do not use the appliance if it has not been installed Be sure the appliance is properly installed and grounded by a qualified technician The appliance may only be installed and connected to the power supply maintained and repaired by a qualified electrician in accordance with safety regulations Do not repair or replace any part of the appliance unless specifically recommended in this manual Work performed incorrectly puts your safety at risk This appliance is for residential use only Use for any other purpose is at the owner s risk and could be dangerous The manufacturer can t be held responsible for damage caused by improper use of this appliance Danger of burning The cook top ET becomes hot during operation 2 CAUTION Keep children away from this appliance CAUTION Items of interest to children should not be stored in cabinets above a cooktop A child can be seriously injured by climbing on a cooktop to reach them Do not leave children alone or unattended in the area where the appliance is in use They should never be allowed to sit or stand on any part of the appliance Don t touch the cooking surface or areas near it The cooking surface may be hot even though it s dark in color Areas near it may become hot enough to cause burns During and after use do not touch the su
3. USA If you touch the plus key the cooking zone starts at setting 5 without an automatic boost If you touch the minus key the cooking zone starts at setting 9 In this case the automatic boost function is automatically activated too Switching off the cooking zone press the plus sensor and the minus sensor simultaneously All cooking zones have an automatic boost function The booster cooking phase is activated at full power The booster cooking time depends on the subsequent cooking level which has been selected after the activation The cooking zone automatically changes to the selected subsequent cooking level as soon as the set booster cooking time has elapsed If the pan on detection function is activated and the pan is removed from the cooking zone the automatic boost function will be cut off When a pan is replaced on the cooking zone the automatic boost function resumes operation again Selecting the required setting by means of the minus sensor will automatically activate the automatic boost function During automatic operation an A will flash in the display in alternation with the cooking level set If the automatic boost function is to be activated when the required setting is selected by means of the plus sensor the plus sensor must be touched again once power level 9 has been reached Sy Residual heat indicators AN w Dual circuit cooking zones Then set it at the required cooking
4. an underlined U appears in the display Then the cooking zone switches off automatically after 1 minute The pan on detection must be switched off when glass cookware or any other cookware unsuitable for the pan on detection is being used Before setting the power level of the cooking zone touch the plus and minus sensors simultaneously The display will show a dot This dot remains visible next to the power level set If the dot blinks it is an indication that the pan on detection has developed a defect The cooking zone can still be operated with the pan on detection switched off Select the circuit manually for dual circuit cooking zones The automatic pan size detection for dual circuit cooking zones 4 ry Y Users Guide EKWE EKWH USA Dual circuit cooking zones have a sensor which recognises the size of the pan being used Only the inner circuit will be switched on if a small pan is placed on the cooking zone If the cooking zone is fully covered by a pan both circuits will be switched on Please ensure that the outer circuit is always fully covered even in the case of pans with a rounded base Moving the pan around during the cooking procedure may result in the outer cooking circuit being switched off if it is not fully covered The outer cooking zone circuit can also be switched on or off manually if the pan on detection or the pan size detection is activated The emergency switch
5. See Installation zone the wrong cooking zone heats up dual instructions lf this dot blinks it is an indication that the pan on detection has developed a defect The cooking zone can still be operated with the pan on detection switched off Should you need to contact Customer service or order spare parts always quote the information printed on the model identification plate It is located underneath the control honeycomb You will also find it stuck onto the front page of the operating instructions enclosed Users Guide EKWE EKWH USA After Sales Service Users Guide EKWE EKWH USA In the event of a problem that you can t easily fix yourself or for spare part service please contact the K ppersbusch Customer Care line at 1 800 459 0844 cg gt Always have the information from the identification panel handy when calling Customer Service The panel is located on the underside of the cook top and on the cover page of this manual Model Production number Kunpparsbuner A F Hr ii Gal earkirahan AC LE U Bee 3 TSH E Mela in Barsana a Tup gt HER GAS 5 hir T asa all 248 H 5A u criss TO UL ST ESA aaa 15 KUPPERSBUSCH USA 4920 West Cypress Street Tampa Florida 33607 Telephone 813 288 8890 Fax 813 288 8604 Customer Care line 1 800 459 0844 www kuppersbuschusa com KUPPERSBUSCH IS A BRAND OF TEKA USA INC K ppersbusch THE FUTURE OF COOKING SINCE 1875
6. by the use of unauthorized parts 2 Service visits to teach you how to use the appliance 3 Service visits to correct the installation You are responsible for providing electrical wiring and other connecting facilities 4 Reset circuit breakers or replace home fuses 5 Damage resulting from accident alteration misuse improper installation abuse or installation not in accordance with local electrical codes or improper storage of the appliance 6 Repairs due to other than normal household use Disposing of the packaging and the old appliance Be sure to dispose of the transport packaging properly Disposal should not have a negative impact on the environment Recycling the packaging saves raw materials and reduces the amount of waste Be sure to dispose of your old appliance properly as well Even if it can no longer be used it still contains useful materials Before discarding an old appliance disconnect the power cord to prevent it from becoming a hazard For your information Carefully read the information in this manual before you use your appliance You ll find important information about safety and how to use maintain and service your appliance so that it enjoys a long service life If you experience any problems first be sure to read the chapter titled What to do if trouble occurs Usually it s easy to solve minor problems yourself and avoid unnecessary service costs Please keep this manual in a sa
7. level An A will flash in the display in alternation with the cooking level set As long as the cooking zone is still hot an H will appear in the display when the cooking zone has been switched off Dual circuit cooking zones are indicated by means of a flashing cooking zone symbol under the plus minus sensors Depending on the size of the pan on the cooking zone the pan on detection will activate either the inner cooking zone circuit alone or both circuits The cooking zone symbol stops flashing when both circuits have been activated lf the pan on detection has been switched off the smaller cooking zone will always heat up Switch on the outer circuit for large pans Touch the cooking zone symbol under the plus minus sensors The cooking zone symbol will stop flashing on activation Touching the cooking zone symbol again will deactivate the dual circuit zone Users Guide EKWE EKWH USA The pan on detection All of the cooking zones have a pan on detection and the dual circuit zone also has a pan size detection The pan on detection will recognize pans made of metal In order to be able to use glass or ceramic cookware the pan on detection must be deactivated When a pan suitable for the pan on detection is placed onto a cooking zone which is switched off the display will indicate a U If no pan or a pan unsuitable for the pan on detection function has been placed on the activated cooking zone
8. used on the range top without breaking due to the sudden change in temperature Follow the manufacturer s instructions Do not place non food items on the cooking surface when it s hot Be careful when working with attachments The connecting cord must not come in contact with the hot cooking surface Do not put plastic on the cooking surface Things that can melt i e plastics foils or sugar must be kept away from the cooking surface Be sure to immediately remove or lift off any melted item from the hot cooking surface Use the supplied cleaning scraper in order to avoid damage to the cooking surface Clean and remove any burned on materials Don t heat these materials repeatedly Lime deposits are harmful to the cooking surface If a wet sponge or cloth is used to wipe spills on a hot cooking area be careful to avoid steam burn Some cleaners can produce noxious fumes if applied to a hot surface Please follow the cleaning and maintenance instructions carefully Users Guide EKWE EKWH USA An overview of your honeycomb cooktop Cooking zones Control honeycomb The honeycomb cooktop is equipped with an easy to operate sensor control system which is operated via the control honeycomb The layout of the cooking zones is shown in the control honeycomb The control honeycomb itself is not indicated The cooking zones can be activated by the touch
9. LED displays No fault normal display after power cuts lf there were no objects on the sensors confirm by means of the off sensor Horizontal lines in the displays running from top to bottom Disconnect the fuse call Customer service Faulty electronic component Not possible to switch off the cooktop Disconnect the fuse call Customer service Faulty electronic component LED display for cooking settings and heat display does not come on or only partially Call Customer service Risk of burning as the temperature warning is not guaranteed LED display defective Cooking zone does not heat up Household fuse defective Check and replace fuse if necessary Child proof lock not unlocked Unlock child proof lock Cooking zone defective Call Customer service Under no circumstances continue to use the outer circuit which is still working Immediately call Customer service Inner circuit of a dual circuit cooking zone defective The plug is not inserted in the power component or in the control honeycomb Put the plug in again Individual sensors or all of the sensors no longer react to touch Power failure or fault in the electronics system Brief disconnection of the cooktop from the power source by means of circuit zones incorrectly allocated the fuse Pan on detection reacts to the wrong cooking No start or faulty start Start up once again
10. User s guide EKWE EKWH OO Kuppersbusch Warranty This warranty is extended to the original purchaser and succeeding owners for products purchased for ordinary home use It does not cover its use in a commercial situation Should the appliance be sold by the original purchaser during the warranty period the new owner will continue to be protected until the expiration date of the original purchaser s warranty period Save your dated receipt or other evidence of the installation occupancy date Proof of original purchase date is needed to obtain service under warranty The warranty applies even if the owner should move during the warranty period KUPPERSBUSCH does not assume any responsibility for con sequential or incidental damages This warranty provides you with certain legal rights You may also have other rights which may vary from state to state What Is Covered For one full year from the date of the original purchase we will provide parts service and labor in your home to repair or replace any part of the cook top that fails because of a defect in materials or workmanship This service is provided free of charge All warranty service will be provided by our authorized Customer Care professionals during normal business hours What Isn t Covered 1 Service by an unauthorized agency will not be reimbursed Likewise the warranty doesn t cover any damage or repairs due to service performed by an unauthorized agency or
11. aneously The bordering around the cooking zone and an LED display in the clock sensor will flash simultaneously In order to deactivate the switch off function touch the plus and minus sensor of the minute minder or switch off the cooking zone Users Guide EKWE EKWH USA Childproof lock sensor lock The childproof lock can be used to protect the appliance against unauthorized use The cooktop must be switched on Activating the childproof lock Touch the key sensor for approx 2 seconds The childproof lock may also be activated while the appliance is in operation In this case however the settings of the cooking zone can only be turned down or switched off An activated childproof lock will be indicated by means of flashing plus and minus sensors of one of the operating fields not required for your honeycomb layout and the flashing control lamp of the locking sensor Please note The touch control not in use which is used to indicate the childproof lock depends on the layout of your honeycomb cooking zones and varies from model to model Attention Switching the cooktop off does not cancel the childproof lock Cancelling the childproof lock Touch the flashing plus and minus sensors simultaneously until an acoustic signal sounds Then touch the key sensor within a period of 2 seconds Note The childproof lock will no long
12. cooking surface with the cleaning scraper If not the cooking surface can be ruined while it s cooling down Steam and or pressure cleaning machines can t be used to clean the appliance This can damage the unit and result in the risk of personal injury Risk of burning Make sure the appliance has cooled down before cleaning If a wet sponge or cloth is used to wipe spills on a hot surface you could be burned by the resulting steam Be aware that some cleaners can produce noxious fumes if applied to a hot surface Please note the instructions regarding cleansers Clean the cooking surface after every use Food residue that hasn t been removed will burn into the surface the next time it s turned on and then these incrustations may be permanent gt Cleanser residues can cause discoloration the next time you turn on the cook top Cloths and sponges that have been used to clean other surfaces can cause discoloring too ce VSR O FIX C is the perfect cleanser for glass ceramic You can get it from KUPPERSBUSCH Customer Service gt gt D D Do not use any aggressive or bleaching cleaning agents that contain active oxygen chlorine or corrosive components abrasive or aggressive cleaning or scouring agents like steel wool soap filled steel wool metal or plastic sponges or similar agents with an abrasive surface Please note the information for the cleaning scraper CAUTION Risk of cutting The blade of the cleaning s
13. craper is very sharp Always keep the cleaning scraper flat on the surface and push the caking away AN Do not scratch the surface with the edge of the scraper and don t damage the sealing with the edge Cleaning the cooking surface Use the cleaning scraper to remove all food residue and fat splashes from the hot cooking surface When the cooking surface has cooled clean it with water and a small amount of detergent with a cleanser for glass ceramic surfaces or with VSR O FIX C A soft brush or a soft sponge can also be used Wipe off the surface with clear water Dry it thoroughly Remove caking Heavy food residue should be soaked first Use a wet cloth for best results It will be easier to remove the food residue Care of the cooking surface Clean the glass ceramic surfaces with a cleanser to protect it from discoloring and reduce the danger of damage from sugar It can also remove stains and discoloration Users Guide EKWE EKWH USA 1 3 What to do if trouble occurs Never unscrew the appliance Only a qualified technician should perform repairs However there are some problems that you can handle yourself First check and see if there have been any operating errors Remember repairs during the warranty period are not free of charge if they are caused by operating errors or non observance of the following instructions Problem Possible cause Solution Circling symbol lines in
14. e in contact with the hot cooking surface CAUTION Overheated greases and oils may ignite themselves Prepare meals with greases and oils very carefully and control the heat Should fats or oils ignite do not use water to extinguish them Smother the fire or flame or use a dry chemical or foam type extinguisher Don t switch the cooking surface on unless you re using it for cooking Never use a cooking zone without a pot or pan set on it Never use the appliance to heat a room Immediately switch off the cooking zone after using with the respective minus key and not just by pot recognition Never leave the cooking surface unattended at high heat settings Boilover can cause smoking and greasy spillovers that may ignite Wear proper apparel Loose fitting or hanging garments should not come in contact with the cooking surface Dish cloths potholders and aprons should not be stored near the surface units To reduce the risk of burns ignition of flammable materials and spillage due to unintentional contact with the untensil the handle of an utensil should be positioned so that it is turned inward and does not extend over adjacent surface units Use only dry potholders Moist or damp potholders on hot surfaces may result in burns from steam Do not let potholder touch a hot surface Do not use a towel or other bulky cloth CAUTION Only certain types of glass glass ceramic ceramic earthenware or other glazed utensils can be
15. er be activated after a power failure Time limit function holiday function The appliance has an automatic time limit function It prevents the appliance from being in operation for a longer period of time The timer of the time limit function depends on the setting of the cooking level The higher the setting of the cooking level the faster it switches off Cooking level Appliance switches off after 9 2 hours 8 7 6 5 3 hours 4 4 hours 3 5 hours 2 1 10 hours Users Guide EKWE EKWH USA 1 1 Other functions selecting pots and pans e f two or more sensor keys are pressed at the same time e g when a pan is mistakenly put onto a sensor key no function is activated An audible signal sounds after 10 seconds The appliance switches off automatically after 20 seconds Exceptions Cancelling the childproof lock Switching off the cooking zones Switching off activating the minute minder of a cooking zone e f you continue to press a sensor key after having set the highest cooking setting an audible signal sounds after 10 seconds After 20 seconds the appliance switches off automatically e The appliance does not automatically switch on again after a power failure A childproof lock which was activated prior to a power failure it will be de activated e The cooktop is switched off if the electronics become overheated All 4 LED displays flash and a cyclical s
16. fe place and pass it on to new owners for their information and safety The following symbols are used in this operating manual The warning triangle will alert you about possible health risks or things that can cause potential damage to your appliance You ll find useful hints and information when you see this symbol For technical information and or replacement parts please contact the K ppersbusch Customer Care line at 1 800 459 0844 For the most efficient assistance please have the Model and Serial numbers for the appliance available Users Guide EKWE EKWH USA Contents Users Guide EKWE EKWH USA Safety instructions cinn nnna i 4 An overview of your honeycomb cooktop mmmunn 5 Before using the appliance for the first time s essssssseeeeees 5 Using the COOKING Zones ununnsnsennnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnn nn 6 Switching the honeycomb cooktop on 6 The cooking levels 6 Automatic boost function 7 Residual heat indicators 8 Dual circuit cooking zones 8 The pan on detection 9 The emergency switch 10 Minute minder and switch off function 10 Childproof lock sensor lock 11 Time limit function holiday function 11 Other functions 12 Selecting pots and pans 12 Gleanind and care 3 1592 aita amateur taamal ks 13 What to do if trouble OCGUFS munennennnanenananenmamnamamen 14 After Sales Service
17. ignal sounds CAUTION Only certain types of glass glass ceramic ceramic earthenware or other glazed cookware are suitable for range top service without breaking due to the sudden change in temperature Follow the manufacturer s instructions gt Only pots and pans made of metal can be used with the pan recognition function To use other kinds of utensils please deactivate the pan recognition function You can save time and power by using ideal pots and pans e Use pots and pans with flat smooth bottoms Uneven bottom surfaces can increase energy usage and the amount of time needed to start the cooking process e Pans with rough bottom surfaces will scratch the glass ceramic cooking area when they are moved around e Use a pan with a diameter at least as large as the cooking area Using undersized cookware will expose a portion of the heating element to direct contact and may result in ignition of clothing e Whenever possible always place a lid on the pan It will help you save a lot of energy Liquids and foods will only boil over if the temperature is set too high The cooking zones enable you to set the required temperature precisely With a little practice you ll learn how to choose the perfect cooking settings so nothing will boil over even when a lid is on Users Guide EKWE EKWH USA Cleaning and care Sugar and food containing sugar i e marmalade and melted plastic must immediately be removed from the hot
18. of a fingertip on the control honeycomb The control honeycomb consists of the following touch controls and sensors A and B Touch controls for the minute minder with plus and minus sensors C Minute minder with a control function D Touch controls for the cooking zones with plus and minus sensors and if required additional sensors for dual circuit cooking zones E Key sensor for the childproof lock F Off sensor Stand by sensor Before using the appliance for the first time Before using the appliance the first time be sure to clean the cooking surface with a mixture of water and mild detergent on a clean cloth Then wipe the surface dry with a non fluffy cloth Users Guide EKWE EKWH USA 5 Using the cooking zones AN Please note the safety instructions Subsequent to initial connection and after a power failure A L will appear briefly in the LED displays Rotating circling symbols will then be indicated This means that various sensors have been checked automatically and that the touch sensitivity has also been newly set Touch the off sensor in order to confirm that there were no objects on the cooking zones or on the sensors These symbols will be switched off immediately if there are no objects on the sensors Otherwise remove any objects and disconnect the cooking zone briefly from the mains fuse once again Important There may not be any objects on the sensors or on the cooking zones while the
19. rface or let clothing or other flammable materials come in contact with it until it s had time to cool Use the proper pan size This appliance is eguipped with different sized surface units Use flat bottomed cookware that is large enough to cover the surface unit heating element The use of undersized cookware will leave a portion of the heating element exposed and direct contact could result in the ignition of clothing Using a proper relationship between cookware and bumers will also improve efficiency Review Selecting pots and pans on page 12 Flammable materials should not be stored near surface units Don t put combustible or flammable objects on the cooking top They could be ignited if the burners are unintentionally turned on Do not use aluminium foil to line the surface unit drip bowis The glass ceramic surface is very durable and can easily withstand light to medium impacts and loads distributed over large areas Be sure to avoid concentrated loads i e spice bottles from falling on the surface to avoid cracking or breaking of the cooking surface CAUTION If the cooking surface becomes cracked or fractured quit using the appliance immediately Disconnect the power and call Customer Service Cleaning solutions and spills may penetrate the broken cooktop and create a risk of electric shock Never flamb under the cooker hood The fat in the filter can ignite The connecting cable must not com
20. sensor sensitivity is automatically being set Switching the honeycomb cooktop on The cooking levels ce Before you start to use a cooking zone put the cook top into the stand by mode Touch the stand by sensor key for about 2 seconds The touch controls of the cooking zones will light up and the appliance will be ready for operation stand by mode Each cooking zone can now be operated individually Cooking zones on which a pan has been placed will indicate a small u The stand by mode automatically switches itself off if no cooking zone is activated within 20 seconds after 10 seconds an acoustic buzzer will indicate that the appliance will switch off after another 10 seconds or if it remains unused for one minute after operation There exist 9 cooking levels The cooking setting required can be activated by means of the plus or the minus sensor It is shown in the display In order to be able to set a cooking level a pan suitable for the pan on detection must have been placed on the cooking zone or the pan on detection must be deactivated The 0 setting remains visible for approx 2 seconds after switch off Cooking level Suitable for 1 3 heating up keeping warm defrosting 4 5 steaming soaking cooking 6 8 frying deep fat frying 9 heating large quantities Users Guide EKWE EKWH USA Automatic boost function Users Guide EKWE EKWH
Download Pdf Manuals
Related Search