Krell Industries Evolution One Stereo Amplifier User Manual
Contents
1. 00000000000000000000000000000000000000000 0050 00 0 00 0 00 0005 00 0 0 00 0 00 0 0 0 0 0 0 000 000 0 00 0 00 gt2. scono ONE About Krell This section describes the Krell Legacy innovative Krell amplifier design and technol ogy and defines key terms used in this reference The Krell Legacy I design every Krell component to set the standard for workmanship style and performance Dan D Agostino High end audio is a demanding pursuit an ongoing quest for excellence in music reproduction that drives equipment manufacturers to strive for the absolute in design and performance With a keen understanding of this passionate drive Krell Industries Inc was founded in 1980 Over the past 2 1 2 decades Krell has earned a distinguished reputation for engi neering innovation and product excellence The company s history is replete with product introductions that have deeply impacted the high end audio industry The most discriminating audiophiles and product reviewers have consistently recognized Krell components for standard setting performance The Evolution One amplifier brings Krell design to a new level setting a standard for performance that will not soon be matched The shear breadth of this amplifier s dynamic range capabilities conveys a startling realism that transcends previous designs Seemingly unlimited frequency response combined with unerring accu racy and fortitude extend a tradition that began with the first Krell amplifier the KSA 100 The KSA 100 was the first high power high current true Class A b
3. 2 2 x 6 gt 0 x 2 1 9 x x x x 22 2 x x 27777777777 2 2 0 o 17 Amplifier Binding Posts 22 Amplifier Front continued SE
4. continued SECTION ONE About Krell continued Definition of Terms Following are the definitions of key terms used in your owner s reference manual Inputs and Outputs Balanced A symmetrical input or output circuit that has equal impedance from both input ter minals to a common ground reference point The industry standard for professional and sound recording installations balanced connections have 6 dB more gain than single ended connections and allow the use of long interconnect cables Balanced connections are completely immune to induced noise from the system or the envi ronment CAST and Evolution CAST Krell Current Audio Signal Transmission or CAST is a proprietary Krell circuit tech nology for connecting analog components transmitting the audio waveform between components in the current domain rather than in the voltage domain The speed and bandwidth provided by Krell CAST and its circuitry update Evolution CAST yield accurate realistic music reproduction enabling connected components to perform as if they are all part of a single circuit Operation Off When the power breaker switch on the back panel of the power supply is in the down position and the power stand by LEDs 4 the backlight 5 and the power meter scale 6 are not illuminated the amplifier is off Stand by A low power consumption status that keeps the audio and regulator circuits at idle The power stand by LEDs 4 are illum
5. In the event that Krell receives a product for warranty service that has been modified in any way without Krell authorization all warranties on that product will be void The product will be returned to original factory layout specifications at the owner s expense before it is repaired All repairs required after the product has been returned to original factory specifications will be charged to the customer at current parts and labor rates All operational features functions specifications and policies are subject to change without notification To register your product for warranty benefits please complete and return the Warranty Registration Card enclosed in the shipping box within 15 days of purchase Thank you Return Authorization Procedure If you believe there is a problem with your component please contact your dealer distributor or the Krell factory to discuss the problem before you retum the component for repair To expedite service you may wish to complete and e mail the Service Request Form in the Service Section of our website at http Awww krellonline com To contact the Krell Service Department TEE 203 799 9954 Monday Friday 9 00 AM to 5 00 PM EST FAX 203 799 9796 E MAIL service krellonline com WEBSITE __http www krellonline com Evolution One PRODUCT MODEL NUMBER SERIAL NUMBER To return a product to Krell please follow this procedure so that we may serve you better 1 Obtain a Re
6. AMPLIFIER Please contact Krell if you have questions not addressed in this guide This product is manufactured in the United States of America Krell is a registered trademark of Krell Industries Inc and is restricted for use by Krell Industries Inc its subsidiaries and authorized agents Evolution Bias is a trademark of Krell Industries Inc and is a Krell technology based on U S Patent No 5 331 291 CAST Evolution CAST and Krell Current Mode are trademarks of Krell Industries Inc All other trademarks are registered to their respective companies 2005 by Krell Industries Inc All rights reserved P N 307772 Contents List of Illustrations page iv A Letter from Dan D Agostino page 1 SECTION ONE About Krell page 3 The Krell Legacy Revolutionary Krell CAST Technology Ensuring Maximum Performance and Definition of Terms SECTION TWO Unpacking and Placement page 12 Opening the Evolution One Shipping Cartons SECTION THREE Anatomy of an Amplifier page 15 Features and Benefits of the Evolution One Design SECTION FOUR Connecting an Evolution One Amplifier to Your System page 19 CAST and Voltage Connections Connection Steps DC Protection Circuitry and Remote Control Options SECTION FIVE Amplifier Operation page 22 Powering Up Adjusting Power Meter Modes Switching between CAST and Voltage Connections Amplifier Care SECTION SIX Amplifier Troubleshooting page 26 WARRANTY page 28
7. And the Krell legacy will continue to evolve with products that deliver innovative engineering perfection in build quality and outstanding audio performance Revolutionary Krell CAST Technology Current Audio Signal Transmission termed CAST is a revolutionary method of con necting analog audio components for unparalleled sonic performance Innovative engineering combines the new Krell CAST circuitry with existing Krell Current Mode technology to create entire CAST systems that reproduce music with incredible range tonality and precision The Voltage Signal Transmission and the Traditional Audio System Traditionally signal is transmitted in the voltage domain between two components In an audio system each component is a discrete entity with unique characteristics that act upon the musical signal independently Each component is unaware of the other components in the system The cables that connect the components also have their own electrical characteristics which affect the sonic presentation of the entire system CAST transmission unifies individual components and interconnects into an electrically linked whole The original signal remains unaltered from source to speaker CAST Basics Here s how a CAST audio system works Internally each CAST source transfers or amplifies current using Krell Current Mode circuitry This current signal is then output using CAST circuitry When the signal is received by a CAST input Kre
8. It is a strong belief of mine that linearity an amplifier s ability to output an exact dupli cate of the input signal is the ultimate measure of that amplifiers worth drive Krell amplifier designs toward the common goal of linearity through the rigorous application of Krell design principles that focus our efforts on four major perform ance factors distortion bandwidth output impedance and current capability The Evolution One excels in each of these areas delivering absolute accuracy from extremely low levels of output virtually at preamplifier levels to astounding awe inspiring amounts of power As the foundation of my new Evolution Series the Evolution One Monaural Power Amplifier is designed to complement the Evolution Two Monaural Power Preamplifier perfectly Combine the Evolution One and Two with my new LAT 1000 loudspeakers and experience the extraordinary capabilities of the Evolution System eo continued A Letter from Dan D Agostino continued have some exciting news for you Work on a new source component for the Evolution Series is ongoing as of this writing Possessed of the unique Evolution technologies that power the amplifier and preamplifier this Evolution source will expose the real advantages of the latest recording formats while taking compact disc playback to the next level encourage you to audition it as soon as it is released Sincerely Daniel D Agostino Chief Executive Officer
9. RETURN AUTHORIZATION PROCEDURE page 30 SPECIFICATIONS page 31 List of Illustrations Figure 1 page 15 Evolution One Amplifier and Power Supply Chassis Front Panels Inset Evolution One Amplifier Channel Front Panel View Figure 2 page 16 Evolution One Amplifier and Power Supply Chassis Back Panels Figure 3 page 17 Evolution One Amplifier Chassis Top Figure 4 page 18 Evolution One Power Supply Chassis Top A Letter from Dan D Agostino Dear Audio Enthusiast Thank you for your purchase of the Evolution One The Evolution One Monaural Power Amplifier represents a watershed in my design philosophy and in my quest for amplifiers that deliver absolute truth in music reproduction This new amplifier operates solely in the current domain with only one voltage gain stage at its output have always been fascinated by the artistry inherent in great musical performances and believe that no component in an audio system equates more closely to the full range of musical expression than the power amplifier The Evolution One reproduces real life dynamics and trans parency in a manner that have not experienced prior to this design It is my pleasure to make it available to you Krell amplifiers are best known for their ability to drive any loudspeaker to sound its best without regard to impedance or efficiency The Evolution One amplifier joins this awesome current capability with a new ultra linear circuit topology
10. between listening sessions Turn the amplifier off using the power breaker switch 21 on the back panel of the power supply chassis 2 when the system is not being used for an extended period of time The procedure for amplifier operation follows Insert the AC power cord plug into the dedicated wall outlet 2 Move the power breaker switch to the up position to place the amplifier in stand by mode The power stand by LEDs 4 on the amplifier and power sup ply chassis illuminate in red 3 Press the power button 3 located underneath the far left edge of the amplifier chassis front panel The power stand by LEDs 4 on the amplifier and power supply chassis illuminate in blue The backlight 5 and the meter scale 6 on the amplifier chassis illuminate in blue You may now switch between CAST and balanced operation For more infor mation see Switching between Cast and Balanced Inputs below 4 With the preamplifier muted or the volume control completely lowered select a source Increase the volume control to the desired listening level 5 To place the amplifier in stand by mode press the power button 3 on the front panel It is now safe to turn off the rest of the system Switching Between CAST and Balanced Inputs If a CAST and balanced source are connected during the initial installation see Cable Connection Steps pages 19 20 the Evolution One defaults to CAST and the CAST LED illuminates in blue when the ampl
11. Factory default Power Meter Range and Power Meter Wand Action The power meter 6 7 enables you to monitor the power output of the Evolution One amplifier The 500 Watt scale is the factory default The 50 Watt scale range is the most sensitive and displays the smallest changes in power output with the greatest physical movement of the power meter wand 7 Conversely the 5000 Watt scale is the least sensitive and displays the largest changes in power output with the smallest physical movement of the power meter wand Turning Off the Lights on the Amplifier Channel Front Panel When the meter range button 12 cycled to OFF the lights on the front panels are not illuminated Amplifier Care An Evolution One amplifier is capable of enormous power output and it is impor tant to exercise care during system operation Avoid any action that can generate large transient signals Always mute the preamplifier output before switching between active sources or cuing an LP Do not change inputs to the amplifiers while the amplifiers are on Use care when listening at high volume levels Because of their tremendous reserve of clean power Evolution One amplifiers can drive loudspeakers to much higher sound pressure levels than other amplifiers without clipping Always lower the volume level at the first sign of loudspeaker distress Exercise great care when handling an amplifier especially at the back panel Rings necklaces brac
12. High relia bility connectors with 56 machined gold plated 20 amp contacts transmit these tremendous power reserves to the regulators Advanced Microprocessor Control Monitors Critical Operational Parameters If the DC level at the amplifier inputs exceeds a safe level the microprocessor control automatically switches in DC blocking capacitors to prevent damage to the input stages or the loudspeakers The microprocessor control measures the load impedance in real time to optimize the performance of the amplifier and power supply or in the case of a short circuit to shut the amplifier off It monitors the regulator output voltages the symmetry between the two halves of the bal anced output stages and it monitors the operating temperatures of the three main heat sinks If any of the heat sinks become too hot the microprocessor control adjusts the operating parameters of the amplifier and power supply to help the circuitry run cooler If the temperature of any of the heat sinks becomes unsafe the microprocessor control shuts the amplifier off until it cools down In the event of a major protection fault the microprocessor flashes a diagnostic code on the power stand by LED 4 The RMS output voltage and current sig nals used by the microprocessor are also used by the power meter 6 7 on the amplifier front panel to display accurate power measurements For more infor mation on diagnostic codes see Amplifier Troubleshooting on page 26
13. hum or other unwanted noise from being introduced into the system D continued SECTION FOUR Connections continued 3 5 6 Connect the Krell CAST cables from your CAST enabled preamplifier or source component to the left and right Krell CAST 4 pin bayonet inputs 16 on the amplifier 1 back panel For balanced operation connect the intercon nect cable from your preamplifier to the balanced XLR input 15 on the ampli fier back panel Connect the loudspeaker cables to the amplifier binding posts 17 located on the amplifier back panel Amplifier binding posts accept spade lugs only Insert the AC mains power cord plug into the IEC power cord receptacle 20 on the back panel of the power supply chassis Turn to Amplifier Operation on page 22 Note If a CAST and balanced source are connected to the amplifier during the initial installa tion the Evolution One amplifier defaults to CAST when it is powered on If only one source is connected the amplifier will automatically select that source For more informa tion see Switching Between CAST and Balanced Inputs on page 23 DC Protection Circuitry Using a Tube Preamplifier The Evolution amplifier has a built in DC monitor that continuously monitors the audio signal at the input If too high a level of DC is detected the amplifier auto matically mutes the output and engages DC coupling capacitors at the input stage For more information about DC pro
14. unit there may be a charge for service even if the product is within the warranty period Freight to the factory is your responsibility Return freight within the United States U S A is included in the warranty If you have purchased your Krell product outside the U S A and wish to have it serviced at the factory all freight and associated charges to the factory are your responsibility Krell will pay return freight to the U S A based freight forwarder of your choice Freight and other charges to ship the unit from the freight forwarder to you are also your responsibility Krell is not responsible for any damage incurred in transit Krell will file claims for damages as necessary for units damaged in transit to the factory You are responsible for filing claims for shipping damages during the return shipment Krell does not supply replacement parts and or products to the owner of the unit Replacement parts and or products will be furnished only to the distributor perform ing service on this unit on an exchange basis only any parts and or products returned to Krell for exchange become the property of Krell No expressed or implied warranty is made for any Krell product damaged by accident abuse misuse natural or personal disaster or unauthorized modification Any unauthorized voltage conversion disassembly component replacement perforation of chassis updates or modifications performed to the unit will void the warranty
15. uses cables manufactured by Krell and other manufacturers spe cially licensed by Krell Thin and flexible CAST cables are constructed with the same build quality as other Krell components and are aesthetically matched to the components that Krell manufactures An all metal body and locking connectors with gold contacts are part of the standard no compromise specification devel oped for every CAST cable made Evolution CAST By employing radical current mirror circuitry the Evolution components elevate the CAST technology to another level This advanced use of the technology increases the linearity transient speed and bandwidth of the Evolution components while reducing the distortion by an order of magnitude The Best Musical Performance When you operate a CAST system you will hear significant improvements in every performance area speed precision dynamic range depth and width of the sound stage transient impact tonal balance harmonic distortion and more The goal for CAST is the same company goal used for all Krell products Krell strives for the delivery of the best performance of a musical event for you using the full expres sion of technology to date Ensuring Maximum Performance My pursuit of excellence in sound reproduction and my love of great musical performance has led me to the Evolution One Amplifier and fuels the ongoing Evolution design effort at Krell Dan D Agostino The Krell Evolution One
16. 450 W RMS at 8 Ohms 900 W RMS at 4 Ohms 1800 W RMS at 2 Ohms Output voltage 170 V peak to peak 60 V RMS Output current 57 A peak Slew rate 100 V us Power consumption Standby 225 W Idle 300 W Maximum 3600 W Inputs 1 balanced via XLR connector 1 CAST via 4 pin bayonet connector Outputs 1 pair Krell binding posts Dimensions Amplifier chassis 15 8 in W x 6 2 in H x 21 5 in D 40 cm W x 15 8 cm H x 54 7 cm D Power supply chassis 15 8 in W x 6 4 in H x 20 5 in D 40 cm W x 16 1 cm H x 52 2 cm D Amplifier channel 15 8 in W x 12 5 in H x 21 5 in D 40 cm W x 31 6 cm H x 54 7 cm D Weight Amplifier chassis Shipped 70 Ibs 31 7 kg Unit Only 55 Ibs 24 9 kg Power supply chassis Shipped 110 Ibs 49 8 kg Unit Only 95 Ibs 43 kg
17. CTION THREE Anatomy of an Amplifier continued Figure 4 Evolution One Power Supply Chassis Top 23 24 0000000 000000 0000000 23 23 Locating Pin 24 Power Connector 25 Power Supply Front scorn FOUR Connecting the Evolution One to Your System This section describes Evolution One amplifier connections and outlines remote control options Each Evolution One has a CAST 4 pin connector a balanced input via an XLR connector a 12 Volt trigger In Out connection and an RC 5 input on the back panel CAST Connections Krell recommends using its proprietary Krell CAST system for unparalleled sonic performance for connections between an Evolution One amplifier and other CAST equipped components Krell CAST uses flexible interconnecting cables that can be drawn through tight spaces and concealed Balanced Connections Evolution One amplifiers also offer balanced connections Balanced connections not only can minimize sonic loss but also are immune to induced noise especially for installations using long cables Cable Connection Steps The following steps describe how to connect cables to an Evolution One amplifier 1 Turn off all power sources and components before connecting inputs and out puts 2 Neatly organize wiring between to and from the amplifier and all components Separate AC wires from audio cables to prevent
18. EVOLUTION EVOLUTION ONE MONAURAL POWER AMPLIFIER OWNER S REFERENCE Evolution One Monaural Power Amplifier Owner s Reference v05 0 Krell Industries Inc 45 Connair Road Orange CT 06477 3650 USA TEL 203 799 9954 FAX 203 891 2028 E MAIL krell krellonline com WEBSITE http Awww krellonline com This product complies with the EMC directive 89 336 EEC and the low voltage directive 73 23 EEC WARNINGS The amplifier must be placed on a firm level surface where it is not exposed to dripping or splash ing The ventilation grids on the top of the amplifier and the space underneath the amplifier must be unobstructed at all times during operation Do not place flammable material above or beneath the amplifier Before making connections to the amplifier ensure that the back panel power switch is down Make sure all cable terminations are of the highest quality free from frayed ends short circuits or cold solder joints The differential circuitry employed with an Evolution One Monaural Power Amplifier requires special attention when connecting speakers Do not connect the negative speaker terminals together Do not connect the negative speaker terminals to ground Do not connect an Evolution One Monaural Power Amplifier to a loudspeaker selector device that employs a common ground scheme as it may short circuit the amplifier output THERE ARE NO USER SERVICEABLE PARTS INSIDE AN EVOLUTION ONE MONAURAL POWER
19. Monaural Power Amplifier built upon the foundation of huge regulated power supplies and output stages is designed to drive any loudspeaker with complete control The product of breakthrough Krell technolo gy this amplifier provides a sound that is supremely dynamic and musical Indeed it is the sound of the music itself Core Technologies Class A Balanced Current Mode Gain Topologies from Input to Output Audio signal voltages are converted to currents at the amplifier input and the audio signal remains in the current domain throughout the entire amplifier until the output stages All signal gain is realized in the current domain using propri etary multiple output current mirrors with extraordinary open loop linearity The current mirrors in the final gain stages use 36 pairs of high voltage high speed transistors Originally developed for demanding high bandwidth video circuits these transistors help yield gain stages with superb accuracy and very low dis tortion The signal path is fully complementary and fully balanced from input to output The driver and output stages use 28 pairs of 150 Volt 14 Amp 50 megahertz power transistors mounted on Krell designed high efficiency heat sinks All transistors operate in Class A mode Independent complementary pre driver and driver stages for the positive and negative output transistors make the output stages extremely fast and linear The output stage develops 450 Watts into an 8 Ohm loa
20. ages in the high current regulators use 14 pairs of the same robust high performance power transistors used in the amplifier output stages All the regulators are located in the amplifier chassis to provide ultra low impedance supply rails for the audio circuitry Evolution Bias Control Systems The new Evolution Bias system features 12 individual bias levels for optimum performance and efficiency Evolution Bias constantly compares the audio signal at the input stage with impedance at the output stage and adjusts the bias cur rent accordingly In addition a proprietary bias monitor continuously measures and adjusts the output stage bias eliminating the need for future adjustment or calibration Separate Power Supplies Are Quiet and Powerful Housed in a separate chassis the power supply makes use of extensive electri cal and magnetic shielding to keep radiated interference out of critical amplifier circuits Internal high current line conditioning circuitry filters RF noise on the AC mains as well as compensating for asymmetric power waveforms and DC on the mains A dedicated 165 VA toroidal transformer with six independent secondary windings powers the amplifier s low level stages gain stages and control circuitry Power for the high current regulators and amplifier output stages comes from two massive 2500 VA toroidal transformers These in turn drive eight 35 amp bridge rectifiers and 120 000 microfarads of filter capacitance
21. d 900 Watts into 4 Ohms and 1800 Watts into 2 Ohms This unique circuit is impervious to low impedance or reactive loads the Evolution One amplifier simply drives any loudspeaker with absolute confi dence achieving the very best possible sonic results 7 continued SECTION ONE About Krell continued Impedance Advantage The output impedance of the final gain stages is one hundredth that of the final gain stage in most power amplifiers This provides extremely wide bandwidth and very high current capability The amplifier does not employ global negative feedback the final gain stages use only 8 dB of local nested negative feedback This is one five hundredth the amount used in most solid state power amplifiers The result is an extraordinarily open liquid effortless sound Robust Power Supply Regulation For Absolute Voltage Stability The rails powering the amplifier s low level and gain stages are regulated twice for total immunity from fluctuations in the AC mains and virtually noise free out put All the regulators use current mode circuitry for wide bandwidth low output impedance and complete immunity to varying load conditions The high current regulators powering the amplifier output stages use fully complementary gain stages and output drivers The resulting wide bandwidth and low output imped ance of the Evolution One surpasses even the stringent demands of the amplifier output stages The driver and output st
22. ded Locate the 4 locating pins 23 and the power connector 24 in the top plate of the power supply chassis See Figure 4 on page 19 Make certain the amplifier chassis feet 13 and the amplifier power connector not shown align with the 4 power supply locating pins and power supply power connector as you lower the amplifier chassis onto the power supply chassis Use the outer edges of the amplifier and power supply chassis as a guide The dimensions of the chassis are identical When viewed from the top the power supply chassis will disappear beneath the amplifier chassis indicat ing proper alignment of the feet pins and power connectors 2 people needed Visually inspect the union between the amplifier and power supply chassis Verify that the each of the amplifier chassis feet has descended upon the power supply chassis locating pins and that both halves of the power connec tors have mated squarely with one another Press firmly on the amplifier chassis to ensure that the connector is properly engaged D continued SECTION TWO Unpacking and Placement continued Placement Before you install an Evolution One amplifier into your system please follow the guidelines in this section to choose its proper location This will facilitate a clean trouble free installation Each Evolution One amplifier requires at least two inches 5 cm of clearance on each side and at least eight inches 20 cm of clearance above the com
23. e 3 Evolution One Amplifier Chassis Top 17 00000000000000000000000000000000000000000 2 5 5 5 552 2 55 5952 55 2 555552 2 5 5555
24. elets and other pieces of metal jewelry can conduct elec tricity Consider removing them before touching any part of the back panel seron SIK Amplifier Troubleshooting System Protection Each Evolution One amplifier has a built in DC monitor that continuously moni tors the audio signal at the input as well as other sophisticated protection cir cuits that monitor other areas of the topology in order to safeguard the amplifier This circuitry constantly evaluates the operation of the amplifiers and provides protection against potentially damaging DC input or output and short circuits Regulator operation is also continuously monitored to ensure constant voltage to the output stage These protective systems are designed to prevent damage to Evolution One amplifiers or loudspeakers caused by other defective components faulty wiring system mishandling or amplifier failure Evolution One amplifiers report operational issues by flashing the power stand by LEDs 4 in red in a specific sequence or by tripping the rear panel breaker 21 as follows Diagnostic Codes Possible Condition Course of Action 1 flash pause 2 flashes Amplifier is over Allow the amplifier repeat then the amplifier temperature to cool When the LEDs reverts to stand by mode stop flashing the ampli fier has cooled down flash pause 5 flashes Short circuit Check all connections repeat then the amplifier on output at the am
25. he amplifier s ability to perform optimally soron THREE Anatomy of an Amplifier This section describes Evolution One features and benefits Figure 1 Evolution One Amplifier and Power Supply Chassis Front Panels a TL 5 pex 6 7 8 4 KRELL EVOLUTION ONI NG 3 10 11 12 a 2 _ 4 KRELL XN 1 Amplifier Chassis Inset 4 2 Power Supply Chassis Evolution One 3 Power Stand by Button oe 4 Power Stand by LED View 5 Backlight 6 Power Meter Scale 13 a 7 Power Meter Wand 8 CAST LED 9 50 W Scale LED 10 5000 W Scale LED 11 Cast Balanced Button LJ 12 Meter Range Button 14 13 Amplifier Feet 14 Power Supply Feet continued SECTION THREE Anatomy of an Amplifier continued Figure 2 Evolution One Amplifier and Power Supply Chassis Back Panels 452 caer os PER Rae O 1 O 2 KRELL oe O BVOLUTION ONE KRELL INDUSTRIES INC C gt ce 5 Hz KRELL BYOLUTION ONS GO _ nae Ne oe i a Ca 15 Balanced Input 16 CAST Input 17 Amplifier Binding Posts 18 RC 5 Input 19 12 V Trigger In Out 20 IEC Power Cord Receptacle 21 Power Breaker Switch Figur
26. iased stereo power amplifier available to audiophiles It was the first Krell product and its resounding success established Krell as an important new technological contrib utor to high end audio continued SECTION ONE About Krell continued From the KSA 100 to the present Krell C E O Dan D Agostino has continually pushed the envelope of performance in his search for greater amplifier power His exploration of new technologies driven by his never ending quest to elevate the standard of excellence has resulted in breakthrough audio designs Over the years the Krell line of power amplifiers including benchmark products such as the KRS 100 KRS 200 and the Audio Standard models has established a legacy of unparalleled sonic performance The Krell product line has diversified but Dan s fundamental research into amplifier design and performance remains at the core of the company s achievements Every Krell component upholds the legacy incorporating unique technologies that are the direct result of Dan s discoveries in audio amplification The Evolution One amplifiers build on the Krell legacy They provide unprecedent ed linearity with the control and accuracy that only comes from superior current capability The sound is lively and unconstrained in a manner that evokes live per formance and the true sound of instruments Dan D Agostino remains committed to the development of new designs and technologies
27. ifier is powered on If only one source is connected the amplifier automatically selects that source If the amplifier detects a balanced source there is no illuminated LED To switch between CAST and balanced inputs press the CAST Balanced button 11 located underneath the far right edge of the amplifier chassis front panel CAST cables must be engaged for this function to be operational continued SECTION FIVE AMPLIFIER OPERATION continued Adjusting Power Meter Modes The Evolution One amplifier uses microprocessors to monitor RMS output voltage and current signals This information is output to a custom front panel power meter 6 7 which displays an accurate power measurement for the selected meter range on the power meter scale 6 The power meter has 4 modes of opera tion accessed by the meter range button 12 50 WATT range 500 WATT range 5000 WATT range and OFF There are two ways to cycles between the operational modes Press the meter range button located underneath the bottom right edge of the amplifier chassis front panel or Press the select key SEL on the Evolution Two preamplifier on another Krell pream plifier or on the Universal Krell Touch Screen Remote Scale Blue Front Panel LED Blue Backlight amp Meter Scale Light 50 Watt 50W LED illuminates Illuminated 500 Watt None Illuminated 5000 Watt 5000W LED illuminates Illuminated Off Meter is inactive Not illuminated
28. inated in red when the amplifier is in the stand by mode Krell recommends leaving the amplifier in the stand by mode when it is not playing music Operation continued Operational Mode When the power stand by LEDs 4 the backlight 5 and the power meter scale 6 are illuminated in blue the amplifier is in the operational mode and ready to play music Technology Krell Current Mode A proprietary Krell circuit topology in which the audio gain stages of a component operate in the current rather than voltage domain This unique technology provides the component with exceptional speed and a wide bandwidth Evolution Bias A patented microprocessor control system that maintains Class A bias operation regardless of musical demand Class A bias is the most accurate method used to amplify musical signals Evolution Bias maximizes an amplifier s efficiency both in power consumption and heat generation sonos WO Unpacking and Placement This section describes the procedures for safely unpacking and placing your Evolution One Monaural Power Amplifier Each Evolution One amplifier channel is shipped in 2 cartons a power supply chassis in 1 carton and an amplifier chassis in the other carton Opening the Amplifier Shipping Carton Each Evolution One shipping carton measures 27 5 in 69 9 cm wide by 12 in 30 5 cm high by 20 8 in 52 8 cm deep and contains 1 amplifier power supply chassis or 1 amplifier cha
29. ll Current Mode circuitry again takes over until the signal reaches the loud speaker By maintaining the musical signal in the current domain from beginning to end an entire CAST system behaves as if it is one component With CAST circuit board properties and signal transmission aberrations between compo nents are eliminated Cable impedances and their effects on the transmitted sig nal are non existent How CAST and Krell Current Mode Interact While CAST is a new method of transferring the musical signal between compo nents its origin stems from Krell Current Mode the technology developed to transfer the musical signal within a component CAST combined with Krell Current Mode takes circuitry signal transmission to the next evolutionary level In essence Krell Current Mode maintains the integrity of the signal within the component and oe continued SECTION ONE About Krell continued How CAST and Krell Current Mode Interact continued CAST preserves the transmitted signal between components Together CAST and Krell Current Mode technologies unify separate Krell components into a single global circuit Krell Current Mode technology enjoys bandwidth increases up to an order of magnitude greater than their voltage based counterparts This dramatic increase in circuit bandwidth delivers near perfection in the audible band that typi cally suffers from phase distortions in voltage circuits CAST Cable Construction A CAST system
30. n Tip 12 V Sleeve GND Notes When the Evolution One is in the operational mode the 12 VDC Out provides 12 Volts of DC output When the component is in the stand by mode or off the DC output is O Volts A minimum of 30 mA is required to operate the 12 Volt trigger sonon FIVE Amplifier Operation Evolution One amplifiers are easy to operate However it is important to exer cise care during operation due to the enormous power output of each amplifier Switching between active sources Such as a CD player or a recording device without muting the preamplifier output or bumping or miscuing a source can generate large transients at low frequencies Evolution One amplifiers may gen erate enough power with these transients to damage loudspeakers IMPORTANT Always mute or fully attenuate the preamplifier level when switching sources Do not change input connections to the amplifier when the amplifier is on Use care when setting high playback levels Because of their tremendous reserves of clean power Evolution One amplifiers can safely drive speakers to higher sound pressure levels than other amplifiers Always lower the volume level at the first sign of loudspeaker distress Powering On Powering Down and Powering Off When powering on any system turn on amplifiers last When powering down turn off amplifiers first Krell recommends leaving the Evolution One amplifier pow ered down in the stand by mode
31. plifier and loud reverts to stand by mode speaker binding posts Cycle the power breaker switch 21 on the power supply and attempt to power on the amplifier Call the factory if the problem persists 1 flash pause 7 flashes repeat then the amplifier reverts to stand by mode Line frequency error The amplifier is set for 60 Hz but is attempt ing to operate via a 50Hz system Contact your local authorized Krell dealer or distributor Output mutes while music is playing and then sound resumes DC detected at input during playback Input capacitors are automatically engaged Check source and preamplifier for excessive DC output Once DC has been elimi nated cycle the power breaker switch 21 to disengage the input capacitors The power breaker switch 21 trips then the amplifier powers off The amplifier repeats this action when powered on Possible component failure Contact your local authorized Krell dealer or distributor or the Krell Service Department Warranty Each Evolution Series amplifier has a limited warranty of five years for parts and labor on circuitry Should this product fail to perform at any time during the warran ty Krell will repair it at no cost to the owner except as set forth in this warranty This warranty does not apply to damage caused by acts of God or nature The warranty described on this page shall be in lieu of any other warranty e
32. po nent to provide adequate ventilation An Evolution One amplifier channel meas ures 15 8 in 40 cm wide by 12 5 in 81 6 cm high by 21 5 in 64 7 cm deep and weighs 150 Ibs 67 9 kg Although Evolution Bias circuitry reduces the high heat dissipation and heat out put of traditional Class A circuitry Evolution One amplifiers still can become hot under normal operation When the front and rear of a cabinet are open the air space between the chassis and shelf must be unobstructed If you place the amplifier in a closed cabinet you may need to modify shelf spacing or use small fans to increase ventilation Place the amplifier as close to the loudspeakers as possible Although Krell CAST technology permits you to use interconnect cables of any length try to keep the cable length to a minimum All Evolution One amplifiers drive the lowest imped ances with ease When impedance is added due to long loudspeakers cable lengths amplifier power is wasted in the cable Long loudspeakers cables reduce the maximum power that is delivered in the loudspeakers AC Power Guidelines Each Evolution One amplifier channel needs to be operated from a dedicated AC circuit rated at a minimum of 20 amps A 30 amp AC circuit is preferable but not required Use the power cord shipped with the amplifier channel to make the AC connection Operation with a power cord other than the one supplied by Krell may induce noise limit current or otherwise impair t
33. ssis Power Supply Chassis The combined weight of the shipping carton and the power supply chassis is 110 Ibs 49 8 kg Each power supply chassis measures 15 8 in 40 cm wide by 6 4 in 16 1 cm high by 20 5 in 52 2 cm deep and weighs 95 Ibs 43 kg Amplifier Chassis The combined weight of the shipping carton and the amplifier chassis is 70 Ibs 81 7 kg Each amplifier chassis measures 15 8 in 40 cm wide by 6 2 in 15 8 cm high by 21 5 in 54 7 cm deep and weighs 55 Ibs 24 9 kg To Remove the Chassis from the Shipping Carton 1 Open a shipping carton and remove the top layer of foam You see these items 1 Evolution One power supply chassis or amplifier chassis 1 packet containing the owner s reference and warranty card 2 Orient the shipping box so that one person stands at the front of the carton and the other person stands at the back of the carton 2 people needed Simultaneously grasp the pair of cardboard handle cutouts at the front and back of the carton and lift the chassis straight up out of the carton 2 people needed Place the chassis in a safe location and remove the protective plastic wrapping 2 people needed Open the remaining 3 cartons of the Evolution One using steps 1 4 above as a guide 2 people needed Place the power supply chassis where you intend to use the assembled ampli fier channel Krell recommends that you do not move the amplifier after it is assembled 2 people nee
34. tection circuitry features see Amplifier Troubleshooting on page 26 Remote Control Options The Evolution One amplifier is compatible with the remote controls included with the Krell Evolution Two preamplifier other Krell preamplifiers or preamplifier processors and it is compatible with the Universal Krell Touch Screen Remote Please contact your authorized Krell dealer distributor or Krell if you wish to pur chase a separate remote control for the Evolution One amplifier The following remote control options are available for amplifiers installed outside of the listening area RC 5 Remote Control Each Evolution One amplifier has an RC 5 remote input 18 on the back panel The RC 5 remote input accepts a remote command enabling it to switch between stand by and operational modes and to switch between CAST and bal anced inputs The RC 5 remote control is used with a third party remote control system that provides RC5 IR data with the carrier intact via a wired connection A stereo tip ring sleeve 1 8 mini connector is used in the following configura tion Tip RC 5 data Ring 5 V Sleeve GND 12 Volt Trigger The Evolution One amplifier has a 12 Volt trigger input output connection 19 that sends and receives 12 VDC power on off 12 V trigger signals to from other Krell components and other devices that incorporate a 12 Volt trigger Mono 1 8 mini connectors are utilized with the following configuratio
35. turn Authorization Number R A number and shipping address from the Krell Service Department 2 Insure and accept all liability for loss or damage to the product during shipment to the Krell factory and ensure all freight shipping charges are prepaid The product may also be hand delivered if arrangements with the Service Department have been made in advance Proof of purchase will be required for warranty validation at the time of hand delivery IMPORTANT Use the original packaging to ensure the safe transit of the product to the factory dealer or distributor Krell may at its discretion return a product in new packaging and bill the owner for such packaging if the product received by Krell was boxed in nonstandard pack aging or if the original packaging was so damaged that it was unusable If Krell deter mines that new packaging is required the owner will be notified before the product is returned To purchase additional packaging please contact your authorized Krell dealer distributor or the Krell Service Department for assistance Oo Specifications Frequency response 20 Hz to 20 kHz 0 05 dB 0 6 Hz to 220 kHz 0 3 dB Signal to noise ratio 118 dB A weighted Gain 25 8 dB Total harmonic distortion lt 0 01 at 1 kHz at 450 W 8 Ohms lt 0 1 at 20 kHz at 450 W 8 Ohms Input impedance Balanced 100 kHz CAST 50 Hz Input sensitivity Balanced 3 08 V RMS CAST 3 08 mA RMS Output power
36. xpressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose There are no warranties which exceed beyond those described in this document If this product does not perform as warranted herein the owner s sole remedy shall be repair In no event will Krell be liable for incidental or consequential damages arising from purchase use or inability to use this product even if Krell has been advised of the possibility of such damages Proof of purchase in the form of a bill of sale or receipted invoice substantiating that the unit is within the warranty period must be presented to obtain warranty service The warranty begins on the date of the original retail purchase as noted on the bill of sale or receipted invoice from an authorized Krell dealer or distribu tor Previously owned equipment when re purchased from an authorized Krell dealer or distributor has the balance of the original warranty based on the origi nal date of manufacture The warranty for Krell products is valid only in the country to which they were originally shipped through the authorized Krell distributor for that country and at the factory There may be restrictions on or changes to Krell s warranty because of regulations within a specific country Please check with your distributor for a complete understanding of the warranty in your country If a unit is serviced by a distributor who did not import the
Download Pdf Manuals
Related Search