Kodak Z1012 IS Digital Camera User Manual
Contents
1. Coffee grounds container removable Grinding coarseness regulator Coffee beans container Compartment for measure Ground coffee funnel Mobile drawer Accessories holder OZZFATH TO monNDpD lt CHNDF OT 10 2007 13 47 Pagina 5 1 Product description 501974402003 UK 8 10 2007 13 47 Pagina 6 1 Product description 501974402003 UK 8 ______ 90 K e 7 KONON lioo gt gt 501974402003 UK 8 10 2007 13 47 Pagina 7 1 Product description 2 10 11 7 9 1 8 12 EXT CHANGE G 6 amp O 4 O o T Control Panel 8 Button to select hot water or OK to confirm I Display 9 Button to rinse the appliance or if the MENU 2 Appliance ON OFF knob light is on to change the menu parameters 3 Coffee taste selection button 10 Button to activate or deactivate menu 4 One or two cups short coffee button parameter setting mode MENU 5 One or two cups standard coffee button 11 MENU light 6 One or two cups long coffee button 12 Steam knob 7 Button to select ground coffee or if the MEN2. and press the OK button for at least 3 seconds to confirm The appliance then displays the setting message in English 22 501974402003 UK 8 10 2007 13 48 Pagina BE 14 Meaning of messages and what to do The tank is dirty or encrusted with lime scale MESSAGE MEANING WHAT TO DO The water tank is empty or is Fill the water tank as described positioned incorrectly in chapter 5 note 6 and insert FILL TANA it fully Rinse or descale the tank The appliance cannot make coffee The coffee runs off too slowly Press the OK button fig 17 Turn the grinding regulator fig 10 one click clockwise see chapter 7 The grounds container is full Empty the grounds container and clean as described in chapter 5 note 7 then replace After cleaning the grounds container has not been replaced Open the service door and insert the grounds container With the ground coffee function selected ground coffee has not been poured into the funnel Add the ground coffee as described in chapter 8 The coffee beans have run out e If the coffee grinder is very noisy this means a small stone in the coffee beans has blocked the mill Fill bean container Contact an authorised service centre DESCALE This indicates the presence of lime scale in the appliance The descaling procedure described in chapter 12 3 needs to be performed as soon as possible After c
3. and pull it out IMPORTANT THE INFUSER CAN ONLY BE REMOVED WHEN THE APPLIANCE IS OFF ATTEMPTING TO REMOVE THE INFUSER WITH THE APPLIANCE ON MAY CAUSE SERIOUS DAMAGE 501974402003 UK 8 10 2007 13 48 Pagina ne 11 Cleaning and maintenance e Wash the infuser under running water without using detergents Never wash the infuser in the dishwasher e clean the inside of the appliance thoroughly To remove coffee encrustations from the inside of the appliance scrape with a plastic or wooden fork fig 25 then vacuum up the residues with a vacuum cleaner fig 26 replace the infuser by sliding it onto the supports and pin at the bottom then push the PUSH symbol fully in until it clicks into place Infuser Push the PUSH symbol fully in until it clicks into place After having heard the click check that the red buttons have snapped out L Support Bottom pipe on the infuser The pin must be inserted into the Pin bottom pipe on the infuser Check that the two red buttons have snapped out otherwise the door cannot be closed The two red buttons have not snapped out The two red buttons have snapped out CORRECTLY CORRECT INCORRECT NOTE If the infuser is not inserted correctly until it clicks into place and the two red buttons have not snapped out the service door cannot be closed NOTE 2 If it is hard to insert the infuser before inserting it squeeze it to
4. APPLIANCE REGULARLY INVALIDATES THE GUARANTEE 12 4 Changing coffee temperature To change the temperature of the coffee proceed as follows Press the CHANGE button the light over the button comes on then press the NEXT button repeatedly until the appliance displays TEMPERATURE MEDIUM Press the CHANGE button until the appliance displays the required coffee temperature Press the OK button to confirm the temperature selected Press the MENU button to exit programming mode or NEXT to change other parameters 12 5 Changing the length of time the appliance remains on The appliance is factory preset to go off automatically one hour after the last coffee has been made The number of hours the appliance remains on can be increased as follows Press the MENU button the light over the button comes on then press the NEXT button repeatedly until the appliance displays GFF AFTER 1 HOUR Press the CHANGE button to change the number of hours the appliance remains on Press the OK button to confirm the value Press the MENU button to exit programming mode or NEXT to change other parameters 21 501974402003 UK 8 10 2007 13 48 Pagina 32 12 Changing and setting the menu parameters 12 6 Setting water hardness The appliance is preset to display the descale message after a set period of time based on a set water hardness You can make descaling less frequent by programming the appliance based on the actual lime content
5. ON position The infuser cannot be removed for cleaning The appliance is on The infuser can only be removed if the appliance is off Turn the appliance off and remove the infuser see chapter 11 2 IMPORTANT the infuser can only be removed if the appliance is off Attempting to remove the infuser when the appliance is on may cause serious damage 24 501974402003 UK 8 10 2007 13 48 Pagina 25 15 Problems that can be resolved before calling the Customer Care Centre PROBLEM Ground coffee is being used not beans and the appliance does not pour the coffee The coffee does not run out from the spouts but from around the service door CAUSE Too much ground coffee has been added The amp button has not been pressed and the appliance has used both the ground coffee added and the coffee ground by the mill Ground coffee has been added when the appliance is off The holes in the spouts are clogged with dry coffee The mobile container inside the service door is blocked and cannot swing SOLUTION Remove the infuser and thoroughly clean the inside of the appliance as described in chapter 11 2 Repeat the operation using a maximum of measure of ground coffee Thoroughly clean the inside of the appliance as described in chapter 11 2 Repeat the operation first pressing the button as described in chapter 8 Remove the infuser and thoroughly clean the
6. and the container with coffee beans fig 3 then close the lid and push the appliance inwards the appliance IMPORTANT to prevent malfunction never fill with ground coffee freeze dried coffee caramelised beans or anything else which could damage the appliance 6 Turn the ON OFF knob fig 4 The appliance displays HEATING UP PLEASE LAIT u to indicate that preheating is underway When preheating is complete the appliance displays RASNO COMPLETE PLEASE WAIT u and performs an automatic rinse cycle a little hot water runs out of the spouts and is collected in the drip tray beneath Tip if you want to make a short coffee less than 60 cc to make it hotter fill the cup with this hot rinsing water first Leave it for a few seconds then empty it to warm the cup 8 The appliance now displays the ready message READY STANDARD TASTE 501974402003 UK 8 10 2007 13 47 Pagina ne 5 Preparing coffee using coffee beans The appliance is preset to make coffee with a standard strength You can also choose coffee with different strengths To choose the required strength press the NO button fig 5 and the selected coffee strength will be displayed 2 Place cup under the spouts to make coffee fig 6 or 2 cups for 2 coffees fig 7 For a creamier coffee lower the spouts to bring them as close to the cups as possible fig 8 3 Press the Sw button to make a short coffee the WW button for a standard
7. in the water used Proceed as follows Remove the Total Hardness Test strip from its packaging then dip it fully in the water for a few seconds Remove it and wait around 30 seconds until it changes colour and a number of red dots are formed Turn the appliance on by pressing the D button fig 4 Press the MENU button then press the NEXT button repeatedly until the appliance displays WATER HARDNESS 4 Press the CHANGE button repeatedly until the number coincides with the number of red squares on the test strip for example if there are 3 red squares on the test strip press the button until WATER HARDNESS 3 is displayed Press the OK button to confirm the value The coffee maker is now programmed to provide the descaling warning when necessary based on the actual hardness of the water 12 7 Resetting factory default settings If you change the original values the factory default values can be reset as follows Press the MENU button then press the NEXT button repeatedly until the appliance displays RESET TO DEFAULT AG e Press the CHANGE button and the appliance displays RESET TO DEFAULT YES Press the OK button to reset the factory default values Press the MENU button to exit programming mode or NEXT to change other parameters 13 Changing the language To change the language proceed as follows Press the CHANGE button for at least 5 seconds until the appliance displays PRESS GK TO IRSTALL ENGLISH
8. inside of the appliance as described in chapter 11 2 Repeat the operation but switch the appliance on first Scrape the holes with a needle see chapter 11 1 Fig 23 Thoroughly clean the mobile container particularly near the hinges to ensure they are free to swing smoothly 25 501974402003 UK 8 10 2007 13 48 Pagina eb After Sales Service Before contacting the Customer Care Centre the Service number the number after the word Switch the appliance on again to see if the problem SERVICE on the rating plate inside the appliance has been eliminated If it has not switch off the your full address appliance and repeat the operation after one hour your telephone number and area code If your appliance still does not work properly after one eus NT on again contact the Customer Care Centre clearly explaining the problem and specifying the appliance type and serial number given on the rating plate the type of fault the model Electrical connection for Great Britain and Ireland only Warning this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 3amp fused plug to change a fuse in this type of plug use an A S T A approved fuse to BS 1362 type and proceed as follows 1 Remove the fuse cover A and fuse B 2 Fit replacement 13A fuse into fuse cover 3 Refit both into plug Important The fuse cover must be refitted when
9. the OK button push any other button to abort the function or wait until the appliance automatically turns back to the main menu 10 Preparing cappuccinos using steam Move the cappuccino maker outwards fig 2 Place an empty container under the cappuccino maker Turn the steam knob fig 18 The appliance displays STEAM PRESS DA Press the OK button fig 17 for steam Allow the steam mixed with water to run off for a few seconds until steam only is given off To interrupt steam delivery turn the steam knob counter clockwise the steam knob fig 18 Note if you accidentally turn the steam knob push any button except the OK button to abort the function or wait until the appliance automatically turns back to the main menu Empty the container then fill it with about 100 grams of milk for each cappuccino to be prepared In choosing the size of the container bear in mind that the milk doubles or triples in volume You are recommended to use semi skimmed milk at refrigerator temperature Dip the cappuccino maker into the milk fig 2 taking care not to immerse the raised line on the cappuccino maker indicated by the arrow in fig 19 Press the steam button beware of burns Steam is discharged from the cappuccino maker giving the milk a creamy frothy appearance To obtain a creamier froth dip the cappuccino maker into the milk and rotate the container with slow movements from the bottom upwards You should not
10. waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 501974402003 UK 8 10 2007 13 47 Pagina 9 Building in Please check the minimum measures mm necessary to the proper installation of the appliance The coffee maker must be installed in a column unit which must in turn be securely fixed to the wall with standard brackets Fasten metal strip using the two screws T So G n a a c 5 D E gt Minimum distance ATTENTION Important the appliance should be disconnected from the mains during installation or maintenance work The kitchen units coming into direct contact with the appliance must be heat resistant min 80 C To ensure correct ventilation leave an opening at the bottom of the unit following the sizes in the drawing 501974402003 UK 8 10 2007 13 47 Pagina act Lean the bars to the surface of the furniture Fix the bars with the screws provided then completely extract the two bars In case of installation above a warmer drawer use the top of the latter as a re
11. 501974402003 UK 8 10 2007 13 47 Pagina 1 KSCX 3610 Instructions for use ee KitchenAid le FOR THE WAY IT S MADE 501974402003 UK 8 10 2007 13 47 Pagina 2 501974402003 UK 8 10 2007 13 47 Pagina 3 1 Product description 2 Important notes Important information for the correct disposal of the product in accordance with EC directive 2002 96 EC Building in 3 Before first use 4 Using for the first time 5 Preparing coffee using coffee beans 6 Changing the quantity of coffee in the cup 7 Regulating the coffee mill 8 Preparing espresso coffee using ground coffee instead of beans 9 Hot water delivery 10 Preparing cappuccinos using steam 11 Cleaning and maintenance 12 Changing and setting the menu parameters 13 Changing the language 14 Meaning of messages and what to do 15 Problems that can be resolved before calling the Customer Care Centre After Sales Service 11 12 13 15 15 16 17 17 18 20 22 23 24 26 501974402003 UK 8 10 2007 13 47 Pagina 4 1 Product description Main ON OFF switch Lights Steam spout Water tank removable Cup tray Drip tray removable Service door Coffee spout adjustable in height Control panel Bean container lid Central ground coffee lid Infuser Power cable Cappuccino maker removable Cappuccino maker nozzle removable Measure for pre ground coffee
12. U light is on to display the next parameter on the menu then release They work just like a 02 To use the knobs turn them clockwise switch 501974402003 UK 8 10 2007 13 47 Pagina 8 2 Important notes READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE CONSULTATION This appliance is designed to make espresso coffee and heat drinks Use with care to avoid scalds from the water and steam jets or through incorrect use This appliance is intended for domestic use only Any other use is considered improper and thus dangerous Do not hang to the appliance when it is extracted The manufacturer is not liable for damage caused by improper incorrect or unreasonable use of the appliance When using the appliance do not touch the hot surfaces Use the knobs or handles Never touch the appliance with any wet part of the body or operate it with bare feet The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance In the event of failure or malfunction unplug the appliance from the mains and do not tamper with it in any way If it requires repair contact an authorised service centre only and ask for
13. always be resolved by following the instructions indicated in chapters 14 and 15 If this is not the case or for further explanations contact the Customer Care Centre by calling the number listed on page 2 of the enclosed sheet If your country is not listed on the sheet call the number indicated on the warranty 501974402003 UK 8 10 2007 13 47 Pagina e 6 Changing the quantity of coffee in the cup The appliance is factory preset to automatically deliver the following quantities of coffee short when the 7 button is pressed standard when the button is pressed long when the W button is pressed To change these quantities proceed as follows press the button corresponding to the quantity you want to change 7 W or W for at least 8 seconds until the message PROGRAM QUANTITY is displayed when the coffee in the cup reaches the required level press the same button again to memorise the new amount 7 Regulating the coffee mill However after making the first few coffees if you find that coffee delivery is either too fast or too slow in drips the grinding coarseness regulator can be adjusted fig 10 Turning it click 1 number clockwise speeds up coffee delivery without drips Turning it click anticlockwise slows down delivery giving a creamier appearance to the coffee These adjustments will only be evident after at least 2 cups of coffee have been run off The grinding coarseness regulator must on
14. be a little water left in the tank when the message is displayed NOTE 7 the appliance counts the number of coffees made Every 14 single coffees or 7 doubles the appliance displays EMPTY GROUNGS CONTAINER indicating that the grounds container is full and must be emptied and cleaned gt Until the grounds container has been cleaned the appliance continues to SS display the message and cannot make coffee To clean open the service door at the front by pulling the coffee spout fig 12 gt remove the drip tray fig 13 empty and clean When proceeding always completely extract the drip tray to avoid it falling when removing the grounds CA 5 iy container NU dr D Empty the grounds container and clean thoroughly making sure all residues NE Sa 7 deposited on the bottom are removed IMPORTANT when removing the drip tray the grounds container MUST be emptied even if it is not completely full If this is not done when next making coffee the grounds in the container may exceed the maximum level and block the appliance NOTE 8 while the appliance is running off coffee never remove the water tank If it is removed the appliance will not be able to make the coffee When using the appliance for the first time 4 5 cups of coffee need to be made before the appliance starts to give satisfying results If the appliance malfunctions do not contact the Customer Care Centre straight away The problem can almost
15. changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug Replacement fuse covers are available from your local electrical store For the Republic of Ireland only The information given in respect of Great Britain will frequently apply but a third type of plug and socket is also used the 2 pin side earth type Socket outlet plug valid for both countries If the fitted plug is not suitable for your socket outlet please contact KitchenAid Service for further instruction Please do not attempt to change plug yourself This procedure needs to be carried out by a qualified technician in compliance with the manufactures instructions and current standard safety regulations 26 501974402003 UK 8 10 2007 13 48 Pagina eb 501974402003 UK 8 10 2007 13 48 Pagina ep Printed in Italy MA 10 07 5019 744 02003
16. coffee and the W button for a long coffee fig 9 To make 2 coffees press the button twice within 2 seconds To change the quantity of coffee delivered automatically into the cup follow the instructions in chapter 6 The appliance now grinds the beans and starts running off the coffee into the cup Once the desired quantity has been reached the appliance automatically stops delivering the coffee and ejects the grounds into the special container 4 After a few seconds the ready message is displayed again and you can make another coffee 5 To turn the appliance off turn the main knob to the OFF position Before switching off the appliance performs an automatic rinse cycle a little hot water runs out from the spouts and is collected in the drip tray beneath Take care to avoid scalds Once switched off the lights will not shut off immediately and the cooling span motor operates to avoid condensation in the housing After about 30 minutes the appliance switches completely off NOTE I If the coffee is delivered a drop at a time or not at all turn the grinding coarseness regulator fig 10 one click clockwise see chapter 7 Turn one click at a time until the coffee is delivered satisfactorily NOTE 2 If the coffee is delivered too fast and is not creamy enough turn the grinding coarseness regulator fig 10 one click anticlockwise see chapter 7 Avoid turning the grinding coarseness regulator excessively otherwise when you sele
17. ct 2 cups the coffee may run out in drips NOTE 3 Tips to make hotter coffee When you turn the appliance on if you want to make a short coffee less than 60 cc use the hot rinse through water to preheat the cups If 2 3 minutes have passed since you last made coffee before making coffee again you must preheat the infuser by pressing the 4 button fig 1 Run off the water into the underlying drip tray or alternatively use this water to fill and then empty the cup to be used for the coffee so as to preheat it Unless preheated do not use cups that are too thick as they will absorb too much heat Use cups that have been preheated by rinsing them with hot water or by leaving them for at least 20 minutes on the cup warmer tray on top of the appliance with the appliance on NOTE 4 while the appliance is making the coffee delivery can be stopped at any time by pressing the SS W or W button as previously selected NOTE 5 as soon as delivery is complete to increase the quantity of coffee simply press and hold the SS w or W button as previously selected until the desired quantity is reached this operation must be performed within 3 seconds from when coffee delivery from the spouts ceases 501974402003 UK 8 10 2007 13 47 Pagina 5 Preparing coffee using coffee beans NOTE 6 when the appliance displays FILL TANA the water tank must be refilled or the appliance will not make coffee It is normal for there to
18. discharge steam for more than two minutes at a time Once the required temperature is reached interrupt steam delivery by pressing the steam button fig 18 Prepare the coffee as described above using large enough cups then fill with the frothed milk prepared previously The cappuccino is ready Sweeten to taste and if desired sprinkle the froth with a little cocoa powder IMPORTANT always clean the cappuccino maker immediately after use Proceed as follows Discharge a little steam for a few seconds by pressing the steam button This empties any milk left inside the steam spout IMPORTANT to guarantee hygiene you are recommended to follow this procedure each time you make cappuccino to avoid milk stagnating in the milk circuit 17 501974402003 UK 8 10 2007 13 48 Pagina act 10 Preparing cappuccinos using steam Press the steam button Wait a couple of minutes for the cappuccino maker to cool down then with one hand hold the cappuccino spout handle firm and with the other unscrew the cappuccino maker itself by rotating clockwise and extracting downwards fig 20 Remove the nozzle from the steam spout by pulling it downwards fig 21 Carefully wash the cappuccino maker and steam nozzle in warm water Make sure the two holes shown in fig 22 are not blocked If necessary clean with a pin Replace the steam nozzle by inserting it and vigorously turning it upwards into the steam spout Replace the cap
19. earn how to operate the appliance correctly may represent a hazard when you use it for the first time follow the step Never install the appliance in environments by step instructions given in the following chapters where the temperature may reach 0 C or lower the appliance may be damaged if the water freezes Make sure the mains voltage corresponds to the voltage indicated on the appliance rating plate Connect the appliance to an efficiently earthed socket with a minimum current rating of 10A only The manufacturer may not be considered liable for possible incidents caused by the failure to adequately earth the mains e If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional Observance of safety directives requires that a multi pole switch with a minimum contact gap of 3 mm be used for the installation Do not use multiple plug adapters or extension leads The power cable on this appliance must not be replaced by the user as this operation requires the use of special tools If the cable is damaged or requires replacing contact an authorised service centre only to avoid all risks For the electrical connection use a H05 VV F type cable as indicated in the table below Conductors Amount x Size 220 240 V 3 x 1 0 mm 501974402003 UK 8 10 2007 13 47 Pagina 2 4 Using for the first time The first time you turn on the app
20. eatedly until the appliance displays START TORE DADO Press the CHANGE button to set the auto start time If you hold the CHANGE button down the time is changed rapidly Press the OK button to confirm the value Press NEXT once and the appliance displays the message RUT O START AG Press the CHANGE button to modify the function the appliance displays AUTO START YES Press the OK button to activate auto start Press the MENU button to exit programming mode or the NEXT button to change other parameters 12 3 Descaling Over time the continuous heating up of the water used to make the coffee leads to lime scale building up in the inner circuits of the appliance When the appliance displays the message DESCALE you should perform the descale cycle Proceed as follows make sure the appliance is ready press the MENU button the light over the button comes on then press the NEXT button repeatedly until the appliance displays BESCALE NO Press CHANGE and the appliance displays the message GESCALE YES Press the OK button to start the descale programme 20 501974402003 UK 8 10 2007 13 48 Pagina aac 12 Changing and setting the menu parameters Empty the tank and pour in the contents of one bottle 125 ml of DURGOL descaler plus one litre of water For subsequent descaling operations descaling solution can be purchased from authorised technical service centres NB Make sure splashes of descaler do not fall ont
21. ference for the coffee maker runners In this case there will be no support surface Put the appliance on its housing and fasten it with the screws 7 811144 2VAb AB UU LU LE BL BLA L BU UU LELE BE BIILB BEE A Fix the power cord with the special clip to avoid the cord entangling when extracting or inserting To align the appliance correctly put the spacers the appliance The power cord must be long under the bar s support enough to allow the extraction of the appliance for refilling the coffee bean container Regulations require that the appliance must be earthed The electrical connection must be made by a qualified electrician in compliance with the manufacturer s instructions and applicable local regulations 501974402003 UK 8 10 2007 13 47 Pagina act 3 Before first use After removing the packaging make sure the You should personalise water hardness as soon product is complete and undamaged If in as possible following the instructions in doubt do not use the appliance and contact a paragraph 12 6 qualified professional The appliance s DATA PLATE is positioned on Installation must be carried out by a qualified the side of the coffee maker so that it remains techncian and in compliance with current visible after installation when the machine is regulations removed from its housing Packing elements plastic bags polystyrene etc must not be left within reach of children as they To l
22. leaning the infuser has probably been left out of the coffee maker Leave the service door closed and the infuser out of the appliance then follow the instructions displayed The service door is open If the service door cannot be closed check that the infuser is inserted correctly chapter 11 2 note 1 GENERAL ALARM After cleaning the infuser has probably been left out of the coffee maker The inside of the appliance is very dirty Insert the infuser see chapter 11 2 Thoroughly clean the inside of the appliance as described in chapter 1 2 If the message is still displayed after cleaning contact a service centre 23 501974402003 UK 8 10 2007 13 48 Pagina ane 15 Problems that can be resolved before calling the Customer Care Centre If the appliance is not working properly the causes of the malfunction can be identified and resolved by referring to chapter 14 If on the other hand no message is displayed run the following checks before calling the customer care centre PROBLEM CAUSE SOLUTION The coffee is not hot The cups have not been preheated The infuser is too cold Heat the cups by rinsing them in hot water or leaving them for at least 20 minutes on the cup warmer tray on the lid see note 3 chapter 5 Heat the infuser by pressing the button before making the coffee fig I 1 see note 3 chapter 5 The coffee is not creamy e
23. liance and every time that it is plugged in when you turn the main ON OFF knob clockwise A the appliance makes a SELF DIAGNOSIS operation and then turns itself off To turn it on again rotate the ON OFF knob 2 clockwise on the control panel The first time you use the appliance select the language Press the main ON OFF switch on the rear side of the appliance the lights on the front side and the display illuminate Wait for the appliance to display PRESS OK TO STALL ENGLISH Press the OK button for at least 3 seconds until the appliance displays ENGLISH STALLED The appliance then displays the setting message in English After a few seconds the appliance displays LL TARA To fill remove the tank fig 1 rinse and fill with fresh water Never exceed the MAX line When removing the tank the cappuccino maker must always be positioned towards the centre of the appliance otherwise the tank cannot be removed Put the tank back and push as far as it will go Move the cappuccino maker outwards fig 2 and place a cup underneath it The appliance now displays PRESS GK Press the OK button After a few seconds a little water runs out of the cappuccino maker When the cup contains about 30cc of water the water stops running and it switches off The appliance now displays TURN GFF PLEASE WAIT and it goes off Extract the appliance by pulling it outwards taking care to use the special handles open the lid
24. ly be turned when the coffee mill is on Turn anticlockwise to obtain finer ground coffee slower delivery and a creamier appearance Turn clockwise for coarser ground coffee and faster delivery not a drop at a time Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill This appliance is however guaranteed to be new 501974402003 UK 8 10 2007 13 47 Pagina seb 8 Preparing espresso coffee using ground coffee instead of beans e Press the amp fig 14 button to select the ground coffee function This disables the coffee mill function The appliance displays READY PRE GROUND Extract the appliance by pulling it using the special handles fig 3 Lift the central lid place one level measure of ground coffee in the funnel see fig 15 Close the lid push the appliance to replace it and proceed as described in chapter 5 Note You can make just one coffee at a time by pressing the w or W button once only NOTE Never add the ground coffee when the appliance is off to avoid it being dispersed inside the appliance NOTE 2 Never add more than one level measured scoop otherwise either the appliance will not make the coffee the ground coffee will be lost inside the appliance dirtying it or the coffee will run off in drips and the message GROUND TOO FINE ADJUST GRINDER AND PRESS OK will be displayed A little water comes out from the
25. nough The coffee is ground too coarsely Wrong type of coffee Turn the grinding regulator one click anticlockwise see chapter 7 Use a type of coffee for espresso coffee makers The coffee runs out too slowly The coffee is ground too finely Turn the grinding regulator one click clockwise see chapter 7 The coffee runs out too quickly The coffee is ground too coarsely Turn the grinding regulator one click anticlockwise see chapter 7 The coffee does not come out of one of the spouts When the steam button is pressed no steam comes out of the cappuccino maker When the D W or W button is pressed the appliance does not deliver coffee but only water The spout holes are blocked The holes in the cappuccino maker and steam nozzle are clogged The ground coffee may be blocked in the funnel Scrape off the dry coffee residues with a needle fig 23 Clean the holes in the cappuccino maker and the steam nozzle see chapter 10 fig 22 Remove the ground coffee inside the funnel using a knife see chapter 8 note 5 Then clean the infuser and the inside of the appliance see description in chapter 11 2 When the D knob is turned the appliance does not switch on The appliance is not plugged in or the main switch on the rear side of the appliance is not switched on Check that the power cable is plugged into the mains socket and the main switch is in the
26. o surfaces sensitive to acid such as marble limestone and glaze Place a container with a minimum capacity of 1 5 litres under the cappuccino maker fig 2 The descaling solution will run out of the cappuccino maker and start to fill the container underneath The descale programme automatically performs a series of run offs and pauses to remove lime scale deposits from inside the coffee maker After about 30 minutes the appliance displays RNS FILL WATER TAR The appliance must now be rinsed through to eliminate residues of descaling solution from inside the appliance Proceed as follows Remove the water tank rinse and fill with clean water mr Reposition the tank the appliance display RINSING PRESS QK Empty the collection container under the cappuccino maker full of liquid and then put it back under the cappuccino maker Press the OK button fig 17 Hot water is run off from the cappuccino maker into the container below and the appliance displays RSG When the water tank is empty the appliance displays the message VISE COMPLETE PRESS OK BUTTON Press the OK button fig 17 and refill the water tank with clean water The descale programme is now terminated and the appliance is ready to make coffee again NOTE if the descaling cycle is interrupted before completion the appliance continues to display the descale message and the programme must be started again from the beginning IMPORTANT FAILURE TO DESCALE THE
27. original spare parts to be used Failure to respect the above could reduce the safety of the appliance This appliance may be installed above a conventional built oven provided it is fitted with a cooling blower on the top side The nominal power of the oven shall not be more than 3Kw Do not rest objects containing liquids inflammable or corrosive materials use the accessories holder to contain coffee accessories for example coffee measure Do not rest big objects that may block the movement of the appliance or unstable objects Avoid exposing the appliance to atmospheric agents The parts which could come into contact with coffee or milk conform to the provisions of the EEC directive 1935 2004 relating to materials suitable for contact with foodstuffs This appliance conforms to EC directive 2004 108 EC on Electromagnetic Compatibility EMC Important information for the correct disposal of the product in accordance with EC directive 2002 96 EC This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol z on the product or on the documents accompanying the product indicates that this appliance may not be treated as household
28. puccino maker by pushing it upwards and turning it counter clockwise 11 Cleaning and maintenance Before performing any cleaning operations leave the appliance to cool down switch off the main switch and unplug from the mains socket Do not use solvents or abrasive cleaning products to clean the appliance A soft damp cloth will suffice NEVER wash ANY of the components of the appliance in a dishwasher 11 1 Cleaning the coffee maker Clean the grounds container as described in chapter 5 note 7 whenever it requires emptying The water tank should also be cleaned regularly The drip tray is fitted with a level indicator red showing the level of water it contains When the indicator starts to become visible a few millimetres under the drip tray the drip tray must be emptied and cleaned Check that the holes in the coffee spout are not blocked To unblock them scrape the dry coffee residues away with a needle fig 23 11 2 Cleaning the infuser The infuser must be cleaned regularly to avoid the build up of coffee encrustations which could cause malfunction Proceed as follows turn the appliance off by rotating the knob counter clockwise fig 4 do not switch off the main switch or unplug and wait for the display to go off open the service door fig 12 remove the drip tray and the grounds container fig 13 and clean press the two red release buttons on the infuser sideways and towards the centre fig 24
29. steam spout NOTE 3 When dosing the quantity of coffee to be added use the measure supplied only NOTE 4 Use ground coffee for espresso coffee makers only Do not use coffee beans freeze dried coffee or other materials that could damage the appliance NOTE 5 If the funnel blocks due to moisture inside the appliance or if more than one measuring scoop of pre ground coffee has been used use a knife to push the coffee down Fig 16 then remove and clean the infuser and appliance as described in chapter 11 2 Cleaning the infuser Once the coffee has been delivered to go back to making coffee using beans deactivate the ground coffee function by pressing the amp button again the light goes off and the coffee mill is enabled for operation again 501974402003 UK 8 10 2007 13 48 Pagina Le 9 Hot water delivery e Always make sure the appliance is ready Turn the cappuccino maker towards the outside of the appliance and place a container under it fig 2 Press the 2 fig 17 The appliance displays HOT WATER PRESS DA e Press the OK button again fig 17 for hot water Hot water runs off from the cappuccino maker and starts to fill the container underneath You should not run off hot water for more than 2 minutes at a time To interrupt hot water delivery press the FA button again fig 17 and place the cappuccino maker in the original position near the centre of the appliance Note if you accidentally push
30. the right size by pressing it forcefully from the top and bottom simultaneously as shown in figure 27 NOTE 3 If it is still hard to insert the infuser leave it out of the appliance close the service door unplug from the mains then plug in again Wait for all the lights to go off then open the door and replace the infuser replace the drip tray complete with the grounds container close the service door 501974402003 UK 8 10 2007 13 48 Pagina ab 12 Changing and setting the menu parameters The following menu parameters and functions can be changed by the user Clock Auto start time Descaling process Coffee temperature Length of time the appliance remains on Water hardness Factory default values 12 1 Setting the clock To set the clock proceed as follows Press the MENU the light over the button comes on then press the NEXT button repeatedly until the appliance displays Press the CHANGE button to set the clock If you hold the CHANGE button down the time is changed rapidly Press the OK button to confirm the value Press the MENU button to exit programming mode or NEXT to change other parameters When the appliance is in stand by you can see the hour by pressing any one of the buttons except the ON OFF button 12 2 Setting auto start time This enables you to set automatic start times Make sure the clock on the appliance is set as described above Press the MENU button then press the NEXT button rep
Download Pdf Manuals
Related Search