Kodak CD913 Digital Camera User Manual
Contents
1. Bleeding Venting Trapped Air With the release valve in the OPEN position 3b and with saddle fully lowered locate and remove the oil filler plug screw Pump 6 to 8 full strokes This will help release any pressurized air which may be trapped within the reservoir Reinstall the oil filler plug screw Study understand and follow all printed materials provided with on this product before use Do not exceed rated capacity Use only on hard level surface This is a lifting device only Immediately after lifting support the load with a pair of appropriately rated jack stands Lift only on areas of the vehicle as specified by the vehicle manufacturer Never wire clamp or otherwise disable the lift control valve to function by other than operator s hand Do not move or dolly the vehicle while on the jack To avoid crushing and related injuries e Never work on under or around a load supported only by hydraulic jack e Always use adequately rated jack stands e Chock each unlifted tire in both directions Do not use this device to lift level lower support nor move a house mobile home travel trailer camper or any building structure Be alert and sober when using this product Do not operate under the influence of drugs or alcohol No alterations shall be made to this product Failure to heed these markings may result in personal injury and or property damage OPERATION Lifting Only attachments and2. Universal Joint 1 12 G251wo000500__ _____NA_ Spring 13 8405 42039 000 Pin 14 14 5405 02028 000 __ RetaimingPin______ 2 ps 423 40000 000 ____ Pistontin_________ 1 16 100 0001500 Return Spring Pedal 2 17 18 G25to009800__________ FootPedal_______ 1 19 G25t0o00mW00________ HandeFok 1 21 423 00011 000 Retumspig_ 1 23 64230001300 Sade 1 pa 5111 5502000 Screw Philips pps 423 00010 000 Cover tC 26 G25400100____ Kmb________ 1 27 5402 04028 000 ___ SpringPin____________ 1 e n eaaa LL N A 5110 04012 000 Screw Philips 1 30 5110 05025 000 5107 05016 000 Screw______________ 1 31 6G423 20000 000 G423 60000 000 Hyd Power Unit 1 32 A20060 0008 AirHose J 1 33 A27060 0003 AirMotor Tt A20060 0007 Lift Control Vave 1 35 A20060 0015 Hose Assembly __ 1 36 A20060 0016 Quick coupler Male 1 37 G25140000 000 G100 90009 K01 HandieAssembly_________ 1 pgs 6423 90004K01 FrontwheelAssemby 2 pg 6250 90004K02__________ CasterAssemby 2 ao _Gaso9009x0s___ BoltAssemly 1 a1_ 851 31000 000_ Pump Assembly 1 42 54520500 Pin pas 307 00012000__ Washer ______ 2 ap 5404 04030 000 RetamingPin____ 2 pas s2o5 00005800_ ___NA____ Nu TT lp G42308 088 includes348AtoJ ______ SealKit for Hyd Unit 1 HR EE eet ei A270
3. 01100 0000 Piston forAirMotor____ 1 lp 22040c L0 22041010 Label s _____ Eo 22040C MO Marval TI Replacement parts illustration for Models 22050C amp 22051C Figure 4 Replacement Parts Illustration for Model 22050C amp 22051C 9 Replacement Parts List for Models 22050C amp 22051C Description Filter Reservoir Filler Plug G651 31002 000 Pump Cylinder alslwWini o D 3 G250 30000 000 Universal Joint G251 00005 000 5405 12036 000 sdh N E P Retaining Pin F 7 13 14 15 22 24 26 A070 40009 000 AAA Q pring Pin ose clip 5110 04012 000 crew Philips 5105 05012 000 rew G250 70000 000 G250 20000 000 yd Power Unit ir Hose ir Motor N A ift Control Valve A20060 0016 Q gt gt T W V T W 3 o o lt QWINININ N N NiNiai ojojoj al W a o 0 0 W D Wu ii 31 34 42 Piston for Air Motor Seal Kit G2501S 074 Contents Description Alelo gt OLO OINI OQ E Back up Washer B Back up Washer D ue S i E HEEE F O ring D53x5 1 G Packing Tt H Oring D15x265 2 Back upWasher______ 2 J Packing for 22050C only 1 2 2 ty 1 1 1 1 Replacement parts illustration for Models 22100C amp 22101C Figure 5 Replacement Parts Illustration f
4. load will come down Maintain control of the rate of speed at which the load lowers at all times 1 Raise load high enough to clear the jack stands 2 Remove jack stands carefully always used in pairs 3 Slowly turn the release valve knob counter clockwise but no more than 1 2 full turn If the load fails to lower a Use another jack to raise the vehicle high enough to reinstall jack stands b Remove the malfunctioning jack and then the jack stands c Use the functioning jack to lower the vehicle 4 After removing jack from under the vehicle fully lower the saddle to reduce ram exposure to rust and contamination MAINTENANCE Important Use ONLY good grade hydraulic jack oil Avoid mixing different types of fluid and Never use brake fluid turbine oil transmission fluid motor oil or glycerin Improper fluid can cause failure of the jack and the potential for sudden and immediate loss of load We recommend Mobil DTE 13M Adding oil 1 With saddle fully lowered set jack in its upright level position Locate and remove oil filler plug screw 2 Fill with oil until 3 16 above the inner cylinder as seen from the oil filler hole Reinstall the oil filler plug screw Changing oil For best performance replace the complete fluid supply at least once per year 1 With saddle fully lowered remove the oil filler plug screw 2 Lay the jack on its side and drain the fluid into a suitable container Note Dispose of hydraul
5. or adapters supplied by the manufacturer shall be used Lift only on area of the vehicle as specified by the vehicle manufacturer Note The jack is equipped with handle position lock To adjust the handle release lock device by pulling the lever up then back until lever is locked into place 1 Follow the vehicle manufacturer s recommended guidelines for lifting Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement 2 Locate and close the release valve by turning the release valve knob clockwise until firm resistance is felt 3 Refer to the vehicle manufacturer owner s manual to locate approved lifting points on the vehicle Center jack saddle under lift point 4 Verify lift point then pump handle or foot pedal to contact lift point To lift pump handle or squeeze lift control valve models 22041C 22051C amp 22101C until load reaches desired height Never use foot pedal to raise load 5 Transfer the load immediately to appropriately rated jack stands NEVER use hydraulic jack as a stand alone device ALWAYS transfer the lifted load IMMEDIATELY to a pair of appropriately rated jack stands Use one pair of jack stands per vehicle Rated capacity is per pair only Do not exceed rated capacity Lowering Be sure all tools and personnel are clear before lowering load Slowly open the release valve The more you turn the release valve knob counter clockwise the faster the
6. Operating Instructions amp Parts Manual OMEGA NA Long Chassis Hydraulic Service Jacks Model Capacity 22040C 22041C 4 Ton 22050C 22051C 5 Ton 22100C 22101C 10 Ton NGA Models 22040C 22050C amp 22100C Models 22041C 22051C amp 22101C Air Options U S Patent No s 5 755 099 5 946 912 5 341 723 A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death e Leer comprender y seguir las instrucci nes antes To avoid crushing and related injuries de utilizar el aparato mm n NEVER work on under or around a e El manual de instrucci nes y la informaci n de load supported only by a hydraulic seguridad deben estar comunicado en lengua del jack ALWAYS use adequately rated operador antes del uso jack stands e No seguir estas indicaci nes puede causar da os personales o materiales SFA Companies http www omegalift com Read this manual and follow all the Safety Rules and Operating Instructions before using this product Printed in China 22040C M1 rev 06 08 ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclus
7. ase valve handle knob a Clockwise until firm resistance is felt to further turning This is the CLOSED release valve position used to raise the saddle b Counter clockwise but no more than 1 2 turn from the closed position This is the OPEN release valve position used to lower the saddle With saddle fully lowered locate and remove cover plate then remove the oil filler plug screw Pump 6 to 8 full strokes This will help release any pressurized air which may be trapped within the reservoir Check oil level Proper oil level will vary from just covering the ram cylinder to 3 16 above it as seen from the oil filler hole Reinstall the oil filler plug screw For air option models 22041C 22051C amp 22101C Pour a teaspoon of good quality air tool lubricant into the air supply inlet of the lift control valve Connect to air supply and operate for 3 seconds to evenly distribute lubricant Note These models are equipped with the popular 1 4 NPT air coupler When installing a different air coupler of your choice ensure that thread tape or compound is used when servicing connections To ensure dependable trouble free operation an inline air dryer and oiler is recommended Ensure that jack rolls freely Raise and lower the unloaded saddle throughout the lifting range before putting into service to ensure the pump operates smoothly Replace worn or damaged parts and assemblies with Omega authorized replacement parts only
8. ic fluid in accordance with local regulations 3 Fill with oil until 3 16 above the inner cylinder as seen from the oil filler hole Reinstall the oil filler plug screw TROUBLESHOOTING Lubrication A periodic coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels casters and pump assemblies move freely To help ensure trouble free operation an inline air dryer and oiler is recommended Cleaning Periodically check the pump piston and ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sandpaper or abrasive material on these surfaces Storage When not in use store the jack with saddle fully lowered REPLACEMENT PARTS refer to page 6 thru12 Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give Model number serial number and parts description Call or write for current pricing SFA Companies 10939 N Pomona Ave Kansas City MO 64153 U S A Tel 888 332 6419 Fax 816 891 6599 E Mail sales omegalift com Omega Website http www omegalift com Symptom Possible Causes Corrective Action Jack will not lift load Jack will lift but not maintain pressure Jack will not lower after unloading Reservoir overfilled e Linkages binding e Fluid level low Poor lift performance Fluid le
9. ive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA Companies SHALL NOT BE LIABLE FORANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SAFETY and GENERAL INFORMATION Save the
10. lable for Models 22041C 22051C amp 22101C Air actuated units require at least 7 8 CFM 110 175 PSI A minimum of 150 PSI air pressure is required to raise rated capacity load NEVER use hydraulic jack as stand alone device After lifting immediately support the lifted vehicle with a pair of appropriately rated jack stands SPECIFICATIONS Capacity Jack Size LxWxH Min Height Max Height Hyd Range Saddle Dia 22040C 22041C 50 5 8 x 15 3 8 x 7 1 2 5 1 2 22050C 22051C 57 3 4 x 17 x 7 5 8 7 6 1 2 22100C 22101C 54 3 4 x 20 x 12 3 4 7 7 3 8 Release Valve Handle Knob Lift Control Valve a TK for air actuated models only Handle Saddle Handle Position Lock Front Wheel Handle Sleeve Foot Pedal Grease Fitting Rear Caster Figure 1 Typical Long Chassis Jack Nomenclature 22051C shown PREPARATION Assembly Always secure the handle into the handle sleeve by means of the bolt lock washer and nut provided Tighten securely to prevent accidental removal of handle while in use Before Use 1 2 3 5 Verify that the product and application are compatible if in doubt call Omega Technical Service 888 332 6419 Before using this product read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the hazards associated with its use To familiarize yourself with basic operation turn the rele
11. or Model 22100C amp 22101C 11 Replacement Parts List for Models 22100C amp 22101C Item G651 31002 000 _ __ i G651 31002 000 Pump Cylinder G651 31001 000 Pump Piston da ajo n _ o G100 90009 K04 Universal Joint 5405 12039 000 wo 5402 05025 000 Pin mk al 7 14 1 1 ala Ojo 2 1 nn e coedo El N A z 32 34 N A G100 44000 000 Hyd Cartridge 6 7 0 1 2 2 2 w Oyo 61001898 G10008 98 Seal Kit for Hyd Unit 1 AN RR eat i ei ft N A 22100610 22101010 Labels Pp 22040C MO Manual 1 37 38 39 40 41 42 12
12. se instructions For your safety read understand and follow the information provided with and on this jack before using The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of this jack is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts are noted Any jack that appears damaged in any way or operates abnormally shall be removed from service immediately If the jack has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until jack has been checked by a factory authorized service center contact distributor or manufacturer for list of authorized service centers It is recommended that an annual inspection be done by qualified personnel Labels and Operator s Manuals are available from manufacturer PRODUCT DESCRIPTION Omega Long Chassis Hydraulic Service Jacks are designed to lift but not support one end of a vehicle Immediately after lifting loads must be supported by a pair of appropriately rated jack stands Air actuated function avai
13. vel low Air trapped in system Will not lift to full extension e Release valve not tightly closed e Overload condition Air pressure inadequate Release valve not tightly closed e Hydraulic unit malfunction e Ensure release valve tightly closed e Remedy overload condition e Ensure adequate air pressure e Ensure release valve tightly closed e Discontinue use contact Omega technical service e Drain fluid to proper level e Clean and lubricate moving parts e Ensure proper fluid level e Ensure proper fluid level e With ram fully retracted remove oil filler plug screw to let pressurized air escape Reinstall oil filler plug screw lt Fluid level low e Ensure proper fluid level Replacement parts illustration for Model 22040C DE SO so D Figure 2 Replacement Parts Illustration for Model 22040C 6 Replacemeni parts illustration for Model 22041C Figure 3 Replacement Parts Illustration for Model 22041C 7 Replacement Parts List for Models 22040C amp 22041C Item 22040C Part 22041C Part Description Qty 2 3 4 5 7 po B300 14002 000 Washer S 1 a G6s513w0z00_____ PumpCyiimder_____ 1 o 851 31001 000_ SS PumpPistoo tt pio wa 100 44000 000 Hyd Cartridge 1 11 423 30000 000 G423 70000 000
Download Pdf Manuals
Related Search