Home

Kenwood KDC-W7037Y Car Stereo System User Manual

1. Reset button 4 English Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe it again with a clean soft dry cloth A Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a clean soft dry cloth Before using this unit for the first time This unit is initially set on the Demonstration mode When using this unit for the first time cancel the lt Demonstration mode Setting gt page 35 About KENWOOD Music Editor of PC application attached to KDC W7537U W7537UY Music Editor is recorded in the CD ROM attached to this unit Refer to the attached installation manual for the installation method of Music Editor Refer to the user s manual recorded in the installation CD ROM and Help of Music Editor for the operation method of Music Editor The unit can play CD USB device created by Music Editor Information about Music Editor upgrade is put on the site www kenwood com About Audio file Playable Audio file AAC LC m4a MP3
2. Characters that conform to ISO 8859 1 can be displayed Characters that conform to ISO 8859 5 or ISO 8859 can be displayed Refer to lt Selecting Russian Characters gt page 33 Russian sales area of KDC W7537UY W7037Y The RDS feature won t work where the service is not supported by any broadcasting station There are places in this manual where lit indicators are described however the only time an indicator will light is in the following settings When Status Display is set to On as mentioned in lt Status Setting gt page 11 The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may be inapplicable How to reset your unit If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed Remove the USB device before pressing the Reset button Pressing the Reset button with the USB device installed can damage the data contained in he USB device For how to remove the USB device refer to lt Playing USB iPod device gt page 21 Press the reset button if the disc auto changer fails o operate correctly Normal operation should be restored KENWOOD
3. Attenuator Turning the volume down quickly Press the ATT button Each time you press the button the Attenuator turns ON and OFF When the Attenuator is ON the ATT indicator blinks Audio Control 1 Select the source to adjust Press the SRC button Refer to lt Selecting the Source gt page 7 2 Enter Audio Control mode Press the VOL knob 3 Select the Basic Audio item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Adjust the Basic Audio item Turn the VOL knob Adjustment Item _ Display Range Rear Volume REAR VOLUME 0 35 Subwoofer level SUB W LEVEL 15 15 System Q USER ROCK User Rock POPS EASY Pops Easy TOP40 JAZZ lop 40 Jazz NATURAL atural Bass level BASS LEVEL 8 8 Middle level MIDDLE LEVEL 8 8 Treble level TREBLE LEVEL 8 8 Balance BALANCE Left 15 Right 15 Fader FADER Rear 15 Front 15 Exit Audio Control mode Volume control mode Source tone memory Puts the set up value in the memory per source 8 English About System Q You can recall the best sound setting preset for different types of music Change each setting value with the lt Speaker Setting gt page 9 First select the speaker type with the Speaker setting USER The ranges selec
4. eAROM gt S MODE scan ADM na 2m eM e E J FNC 1 6 SRC Control knob Program Service name 5T PS_ F Hi ich Kenn R TENT Fagdig Text CLOCK Radio text Function icon Traffic Information Traffic information can be switched when it is on the Tuner Source However you cannot switch the Traffic information during reception of the Traffic bulletin switched from the source other than the Tuner Changing to traffic information automatically when a traffic bulletin starts even when you are not listening to the radio Press the TI button Each time you press the button the Traffic information function turns ON and OFF When a traffic bulletin starts Traffic INFO is Radio Text Scroll displayed and the audio changes to traffic Scrolling the displayed radio text information Push the Control knob toward up for at least 2 seconds During reception of an AM station when the Traffic nformation function is turned ON the frequency changes to an FM station When the lt Display Illumination Control gt page 29 is set During reception of traffic information the adjusted to OFF the display may black out while scrolling volume is automatically remembered and the next time the audio changes to traffic information the volume automatically becomes the remembered volume Receiving other traffic information stations Push the Cont
5. Do not touch the recording surface of the CD byproducts Contact your local authority Do not stick tape etc on the CD or use a CD with for details in locating a recycle facility ape stuck on it nearest to you Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment Do not use disc type accessories Clean from the center of the disc and move outward Wh ing CDs from this unit pull th t x fore igen eee ne pe The marking of products using lasers If the CD center hole or outside rim has burrs Except for some areas use the CD only after removing the burrs with a ballpoint pen etc CLASS 1 LASER PRODUCT CDs that cannot be used CDs that are not round cannot be used The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class There is no Oy danger of hazardous radiation outside the unit CDs with coloring on the recording surface or CDs hat are dirty cannot be used This unit can only play the CDs with qs di This unit may not correctly play discs which do not have the mark You cannot play a CD R or CD RW that has not been inalized For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual 6 Engl
6. Oldies Music Oldies Music 30 Folk Music Folk Music 31 ocumentary Documentary 18 English Speech and Music include the Program type shown below Music No 12 17 26 30 Speech No 3 11 18 25 31 You can put the Program Type in the 1 6 button memory and for quick recall Refer to the lt Program Type preset gt page 18 You can change the display language Refer to lt Changing Language for PTY Function gt page 19 3 Search for the selected Program Type station Push the Control knob towards ka a or gt gt When you want to search for other stations push maa or gt gt of the Control knob again When the selected Program Type is not found No PTY is displayed Select another Program Type 4 Exit PTY mode Press the Control knob Program Type preset Putting the Program Type in the Preset button memory and quick recall Presetting the Program Type 1 Select the Program Type to preset Refer to lt PTY Program Type gt page 18 2 Preset the Program Type Press the desired 1 6 button for at least 2 seconds Recalling the preset Program Type 1 Enter PTY mode Refer to lt PTY Program Type gt page 18 2 Recall the Program Type Press the desired 1 6 button Changing Language for PTY Function Selecting the Program Type display language 1 Enter PTY mode Refer to lt PTY Program Type gt page 18 2 Enter Changing Language mode Pr
7. Selectable Illumination Display Illumination Control Dimmer Switching preout Built in Amp Setting Dual Zone System Setting Supreme Setting B M S Bass Management System B M S Frequency Offset AMP Control News Bulletin with Timeout Setting Local Seek Tuning Mode AF Alternative Frequency Restricting RDS Region Region Restrict Function Auto TP Seek Monaural Reception Auxiliary Input Display Setting amp Disc Naming Selecting Russian Characters Text Scroll Built in Auxiliary input Setting Power OFF Timer CD Read Setting Audio Preset Memory Audio Preset Recall Firmware version display Demonstration mode Setting Basic Operations of remote control 36 Accessories Installation Procedure 38 Connecting Wires to Terminals 39 Installation Removing the Unit 41 Troubleshooting Guide 43 Specifications 46 Safety precautions AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Do not watch or fix your eyes on the unit s display when you are driving for any extended period Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals ACAUTION To prevent damage to the machine take the following precautions ake sure to ground the unit to a
8. a 1 Function of KDC W7537U W7537UY 2 Function of KDC W7037 W7037Y The a or gt symbol shown beside the displayed item indicates that the item is preceded or followed by another item Selecting a music will play it from the beginning Cancelling File Select Press the FNC button Even when the iPod is connected you can change the operation method from lt Operation method for iPod gt to lt Operation method for other than iPod gt Refer to lt iPod mode setting gt page 28 English 25 Menu system KENWOOD enera FNC S MODE_ SCAN Le re TE TE FNC SRC Control knob Function icon HERT DISE Menu System You can continue by returning to step 2 and F i setting other items Setting beep sound during operation etc functions 4 Exit Menu mode The Menu system basic operation method is Press the FNC button explained here The reference for the Menu items and their setting content is after this operation When other items those applicable to the basic explanation operation method above are displayed their setting content chart is entered Normally the setting listed at 1 Enter Menu mode the top of the chart is the original setting Using the Control knob select MENU Also the explanation for items that are not applicable For the operation method refer to lt Function lt M
9. mp3 WMA wma WAV wav KDC W7537U W7537UY only Playable disc media CD R RW ROM Playable disc file format ISO 9660 Level 1 2 Joliet Romeo Long file name Playable USB device KDC W7537U W7537UY only USB mass storage class iPod with KCA iP200 e Playable USB device file system KDC W7537U W7537UY only FAT16 FAT32 Although the audio files are complied with the standards listed above the play maybe impossible depending on the types or conditions of media or device Playing order of the Audio file In the example of folder file tree shown below the files are played in the order from to 0 Qo A Folder L da e Audio file E DO L 7 DO 1 do _ do An online manual about audio files is put on the site www kenwood com audiofile On this online manual detailed information and notes which are not written in this manual are provided Make sure to read through the online manual as well In this manual the word USB device is used for flash memories and digital audio players which have USB terminals The word iPod appearing in this manual indicates the iPod connected with the KCA iP200 optional accessory The iPod connected with the KCA iP200 can be controlled from this unit iPods that can be connected with the KCA iP200 are the iPod nano and the iPod with video When an iPod is connected using a commercially available USB cable it is handled as a mass storage
10. 1000 400 rpm CLV 2times Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 008 KDC W7537U W7537UY 0 010 KDC W7037 W7037Y Signal to Noise ratio 1 kHz 110 dB KDC W7537U W7537UY 105 dB KDC W7037 W7037Y Dynamic range 93 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio 46 English AAC decode AAC LC m4a files WAV signal Linear PCM KDC W7537U W7537UY USB Interface KDC W7537U W7537UY USB Standard USB1 1 2 0 File System FAT16 32 Maximum Supply current 500 mA MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files WAV signal Linear PCM Audio section Maximum output power 50Wx4 Output power DIN 45324 B 14 4V 30Wx4 Speaker impedance 4 8Q Tone action Bass 100 Hz 8 dB Middle 1 kHz 8 dB Treble 10 kHz 8 dB Preout level Load during disc play 2500 mV 10 kQ Preout impedance lt 6000 Auxiliary input Frequency responce 1 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input impedance 100 kQ General Operating voltage 11 16V allowable 144V Current consumption 10A Installation Size W x H x D 182 x 53x 155mm Weight 1 40 kg KENWOOD
11. Bass boost level is high 18dB Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit For amplifiers there are the models you can set from Flat o 18 dB and the models you can set from Flat to 12 dB When an amplifier that can only be set to 12 is connected to the unit AMP Bass 18 will not work correctly even if it is selected Other than Standby mode B M S Frequency Offset Setting the central frequency boosted by B M S News Bulletin with Timeout Setting The tuner automatically changes when a news bulletin starts even if the radio is not being listened to Also you can set the time interval when Display Setting interruption is prohibited AMP FREQ Normal Boost with the normal central frequency AMP FREQ Low Drop the normal central frequency 20 Display and Setting News OFF News 00min When LX AMP unit connecting News 90min AMP Control When you set News 00min News 90min You can control the LX AMP connected to the unit 1 Select AMP Control mode Turn the Control knob Select the AMP Control display 2 Enter AMP Control mode Press the Control knob for at least 1 second 3 Select the AMP Control item for adjustment Push the Control knob towards up or down For the details on the AMP Control item see the Instruction manual attached to the LX AMP 4 Adjust the AMP Control item
12. Push the Control knob towards right or left 5 Exit AMP Control mode Press the FNC button You cannot use the LX AMP operation during standby mode the News Bulletin Interrupt function is ON When the news bulletin starts NEWS is displayed and the tuner changes to the news bulletin If you choose the News 20min setting further news bulletins will not be received for 20 minutes once the irst news bulletin is received The news bulletin volume is the same level that was set or lt Traffic Information gt page 17 This news bulletin function is only available if the desired station sends PTY code for news bulletin or belongs to lt Enhanced Other Network gt Network sending PTY code or news bulletin When the News Bulletin Interrupt function is ON the uner changes to an FM station English 31 Menu system In Tuner mode Local Seek Only stations whose reception is good are searched in auto seek tuning Display Setting Local Seek OFF The local seek function is OFF Local Seek ON The local seek function is ON In Tuner mode Tuning Mode Sets the tuning mode Tuning mode Display Operation Auto seek Seek Mode Automatic search for a station Auto1 Preset station seek Seek Mode Search in order of the stations in Auto2 the Preset memory Manual Seek Mode Normal manual tuning control Manual AF Alternative Frequency When the
13. Returns to the previous item 3 Select an option for the selected item Refer to the related pages for the operation of each option 4 Exit Function Control mode Press the FNC button for at least 1 second 10 English Display Type Selection Changing the display mode 1 Enter Display Type Selection mode Using the Control knob select DISP gt TYPE For the operation method refer to lt Function Control mode gt page 10 2 Select the display Type Turn the Control knob Select from the following display types Display Mode Display TYPE SELECT A TYPE SELECT B e TYPE SELECT C a TYPE SELECT D a TYPE SELECT E 5 0 Graphic display part Status display Text display part Upper text display part Middle text display part Lower text display part Text display part Graphic display part Text icon display part Source icon display part 3 Exit Display Type Selection mode Press the Control knob To change the information by the Display Type refer to the page on the following table for the methods to alternate by the Display Type Display Type A B C D E Graphic 11 11 cad Status 11 11 Text 12 Upp
14. and backwards between disc folders gt I button Each time you press the button the music is played or paused 0 9 buttons When in lt Direct Music Search gt page 22 and lt Direct Disc Search gt page 22 enters the music disc number English 37 Accessories Installation Procedure Accessories Installation Procedure 1 To prevent short circuits remove the key from the ignition and disconnect the terminal of the battery 2 Make the proper input and output wire connections for each unit 3 Connect the wire on the wiring harness 4 Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle 5 Take Connector A on the wiring harness and connect it to the external power connector on your vehicle Connect the wiring harness connector to the unit Install the unit in your car Reconnect the terminal of the battery Press the reset button A If the power is not turned ON Protect is displayed the speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked Oo CON OD 38 English If your car is not prepared for this special connection system consult your Kenwood dealer Only use antenna conversion adapters ISO JASO when the antenna cord has an ISO plug Make sure t
15. class device For the supported formats and types of USB device refer to www kenwood com usb About USB device Install the USB device in the place where it will not prevent you from driving your vehicle properly You cannot connect a USB device via a USB hub Take backups of the audio files used with this unit The files can be erased depending on the operating conditions of the USB device We shall have no compensation for any damage arising out of erasure of the stored data No USB device comes with this unit You need to purchase a commercially available USB device For how to play the audio files recorded in a USB device see lt CD USB device Audio file External disc control features gt page 20 When connecting the USB device usage of the CA U1EX option is recommended Normal playback is not guaranteed when a cable other than the USB compatible cable is used Connecting a cable whose total length is longer than 5 m can result in abnormal playback About DAB Tuner control Refer to A group on the Instruction manual of DAB Tuner KTC 9090DAB optional accessory for the control method of DAB Tuner function However the following control methods of the function for this unit may be differed from the Instruction manual therefore refer to the following supplemental instruction lt Auto Ensemble Memory Entry gt 1 Select the preset band for Auto Ensemble Memory Entry 2 Press the AM
16. device Audio file External disc control features Disc Naming DNPS Attaching a title to a CD 1 Play the disc you want to attach a name to A title cannot be attached to MD or Audio file media 2 Enter Menu mode Using the Control knob select MENU For the operation method refer to lt Function Control mode gt page 10 MENU is displayed 3 Select Name set mode Push the Control knob towards up or down Select the Name Set display 4 Enter Name set mode Press the Control knob for at least 1 second 5 Move the cursor to the enter character position Push the Control knob towards right or left 6 Select the character type Press the Control knob Each time you press the knob the character type alternates between the types shown in the table below Character type Alphabet upper case Alphabet lower case Numbers and symbols Special characters Accent characters 7 Select the characters Turn the Control knob or push it towards up or down You can enter characters by using a remote control with a number button Example If you enter DANCE Character Button Times pressed D B 1 A 2 1 N l6 2 ot 2 3 jE B 2 8 Repeat steps 5 through 7 and enter the name 24 English 9 Exit Menu mode Press the FNC button When operation stops for 10 seconds the name at that time is registered and Name Set mode closes Media that you can attac
17. display Refer to lt Selecting the Source gt page 7 2 Select the band Push the Control knob towards FM or AM Each time you push the knob toward FM it switches between the FM1 FM2 and FM3 bands 3 Tune up or down band Push the Control knob towards ka a or gt gt During reception of stereo stations the ST indicator is ON English 15 Tuner features Function of remote control Direct Access Tuning Entering the frequency and tuning 1 Select the band Press the FM or AM button 2 Enter Direct Access Tuning mode Press the DIRECT button on the remote control js displayed 3 Enter the frequency Press the number buttons on the remote control Example Desired frequency Press button 92 1 MHz FM 0 9 2 1 810 kHz AM 0 8 1 0 Cancelling Direct Access Tuning Press the DIRECT button on the remote control You can enter the FM band frequency in steps of a minimum of 0 1 MHz Station Preset Memory Putting a station in the memory 1 Select the band Push the Control knob towards FM or AM 2 Select the frequency to put in the memory Push the Control knob towards ka a or gt gt 3 Enter Preset Memory mode Using the Control knob select P MEM For the operation method refer to lt Function Control mode gt page 10 4 Select the number to put in the memory Turn the Control knob 5 Determine the number to put
18. file system of the connected USB device is broken Copy the files and folders for the USB device again referring to http www kenwood com usb If the error message is still displayed initialize the USB device or use other USB devices Read Error Error 05 The disc is unreadable Blank Disc Nothing has been recorded on the MD o Track No tracks are recorded on the MD although it has a title Error 15 Media was played that doesn t have data recorded that the unit can play o Panel The faceplate of the slave unit being connected to this unit has been removed Error 77 The unit is malfunctioning for some reason gt Press the reset button on the unit If the Error 77 code does not disappear consult your nearest service center Mecha Error Something is wrong with the disc magazine Or the unit is malfunctioning for some reason gt Check the disc magazine And then press the reset button on the unit If the Mecha Error code does not disappear consult your nearest service center 44 English Hold Error The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60 C 140 F stopping all operation Cool down the unit by opening the windows or turning on the air conditioner As the temperature falls below 60 C 140 F the disc will start playing again No Name Attempted to display DNPS during the CD play havin
19. reception is poor automatically alternate to another frequency broadcasting the same program in the same RDS network with better reception Display Setting AF ON The AF function is ON AF OFF The AF function is OFF When the AF function is ON the RDS indicator is ON When no other stations with stronger reception are available for the same program in the RDS network you may hear the incoming broadcast in bits and snatches Turn OFF the AF function in such a case 32 English Restricting RDS Region Region Restrict Function You can choose whether or not to restrict the RDS channels received with the AF function for a particular network to a specific region Display Setting Regional ON The Region Restrict Function is ON Regional OFF The Region Restrict Function is OFF If AF function is not restricted to the specified region and network the AF function sets up to search the station with good reception in the same RDS network Auto TP Seek When the TI function is ON and the reception is poor while listening to a traffic information station another traffic information station with better reception will be searched for automatically Display Auto TP Seek ON Auto TP Seek OFF Setting The Auto TP Seek Function is ON The Auto TP Seek Function is OFF In FM reception Monaural Reception You can reduce the noise when stereo broadcasts are rece
20. 537UY KDC W7037Y In Standby mode Selecting Russian Characters Setting up the display of Russian characters and undistinguishable English characters Display Setting Russian ON Displays texts using Russian characters Russian OFF Displays texts using European characters Texts displayed using Russian characters are as follows Folder name File name Music title Artist name Album name KCA BT100 optional accessory Texts cannot distinguish upper case and lower case in Russian characters Text Scroll Setting the displayed text scroll Display Setting Scroll Manual Doesn t scroll Scroll Auto Scrolls when the display changes The text scrolled is listed below CD text Folder name File name Music title Artist name Album name MD title Radio text English 33 Menu system In Standby mode Built in Auxiliary input Setting Set the Built in Auxiliary Input function Display Setting Built in AUX OFF When selecting the source there s no Auxiliary Input Built in AUX ON When selecting the source there s Auxiliary Input In Standby mode Power OFF Timer Setting the timer to turn this unit s power OFF automatically when Standby mode continues Using this setting can save the vehicle s battery power Display Setting Power OFF Power OFF Timer function is OFF Power OFF 20min Original setting Turn
21. D KCA iP200 Optional accessory AOaIO OUT No other optional accessory can be connected because the USB connector and the AUX input are used for iPod connection Dual Zone System in lt Audio Setup gt page 8 will become unavailable Connecting Wires to Terminals Do not remove the cap when you do not use the USB cable The connector will cause the unit to malfunction B device if it gets in touch with any metallic part of the vehicle 1 Front left output White Front right output Red USB connector 1m KDC W7537U W7537UY only Rear left output Sub Woofer left output White REAR Rear right output Sub Woofer right output Red 1 SUB 1 WOOFER To External Display Steering remote 1 1 cece FM AM antenna input lt aen lt 4 O Antenna Cord ISO Antenna Conversion Adaptor ISO JASO Accessory AUX input Stereo Use the mini plug which is stereo type and does not have any resistance Fuse 10A To Kenwood disc changer External optional accessory HN Wiring harness To connect these leads refer to the relevant instruction manuals Accessory External amplifier control wire eae To EXT AMP CONT terminal of the amplifier having the external amp control function TEL mute wire Brown Connect to the terminal that is grounded when either the telephone rings
22. Date mode Press the Control knob for at least 1 second 3 Select the date format Turn the Control knob or push it towards up or down 4 Exit Date mode Press the FNC button In Standby mode Date Adjustment 1 Select Date Adjust mode Turn the Control knob Select the Date Adjust display 2 Enter Date Adjust mode Press the Control knob for at least 1 second The date display blinks 3 Selecting the item day month or year to adjust Push the Control knob towards right or left The items that are blinking are items that you can adjust 4 Adjust each item Turn the Control knob or push it towards up or down 5 Repeat step 3 and 4 operation and adjust the date 6 Exit Date adjustment mode Press the FNC button In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit s clock Display Illumination Control This function turns off the display when you perform no operation for 5 seconds This function is effective when you are driving at night Display Setting Display Setting SYNC ON Synchronizes the time Display ON Keeps the display on SYNC OFF Adjust the time manually Display OFF Turns off the display when you perform no operation for 5 seconds It takes 3 to 4 minutes to synchronize the clock In Standby mode DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potent
23. E button for at least 2 seconds Open Auto Ensemble Memory Entry After storing in the memory finishes the number of the pre set buttons and the ensemble label are displayed lt Searching by programme type and language gt and lt Languages to be displayed gt in lt Programme Type PTY Function gt At the operation to press DISP button use TI button instead English 5 Notes About Bluetooth Hands free control This Product is not installed by the manufacturer of a Refer to the instruction manual of the Bluetooth vehicle on the production line nor by the professional Hands Free Box KCA BT100 optional accessory importer of a vehicle into an EU Member State About Menu operation For how to operate Menu refer to lt Menu System gt Information on Disposal of Old Electrical in this instruction manual For the items to be set up refer to the instruction of Hands Free Box About display of Cell Phone Status Cell Phone Status is displayed in the status display of this unit For the information about the displayed icons refer to the instruction manual of Hands Free and Electronic Equipment applicable for EU countries that have adopted separate waste collection systems Products with the symbol crossed out wheeled bin cannot be disposed as household waste Box Old electrical and electronic equipment mam Should be recycled at a facility capable Handling CDs of handling these items and their waste
24. File Scan SCAN Plays the beginnings of the audio SCAN iles in the current folder or genre one after another for 10 seconds each Folder RDM RDM Plays the audio files in the curren RDM older or genre at random All Random A RDM Plays the audio files in the curren A RDM disk or USB device at random File Repeat REP Plays the current audio file FIREP repeatedly Folder Repeat REP Plays the audio files in the curren FoREP older or genre repeatedly Irack Scan SCAN Plays the beginnings of the music on SCAN he current CD MD one after another or 10 seconds each Disc Random RDM Plays the music on the current CD RDM D at random Magazine RDM M RDM Plays the music in the disc changer M RDM at random Track Repeat REP Plays the current music on the TREP current CD MD repeatedly Disc Repeat REP Plays the music on the current CD D REP D repeatedly The functions listed in the table above can be operated with buttons on the unit Function of KDC W7537U W7537UV Press the A RDM button for at least 1 second Press the REP button twice 2 Select an option for the selected item Press the Control knob Pressing the Control knob switches between options 3 Exit Play Function Set mode Press the FNC button Only the icons available to the current source are displayed English 23 CD USB
25. KENWOOD CD RECEIVER KDC W7537U KDC W7537UY KDC W 7037 KDC W7037Y INSTRUCTION MANUAL Kenwood Corporation Contents Safety precautions 3 Notes 4 General features 7 Power Selecting the Source Volume Attenuator Audio Control Audio Setup Speaker Setting Subwoofer Output TEL Mute Function Control mode Display Type Selection Status Setting Graphic Display Selection Text Display Selection Display Type B amp E Text Display Selection Display Type C amp D The text display Theft Deterrent Faceplate External Display Selection a Tuner features 15 Tuning Direct Access Tuning Station Preset Memory Auto Memory Entry Preset Tuning Traffic Information Radio Text Scroll PTY Program Type Program Type preset Changing Language for PTY Function 2 English RDS features 17 CD USB device Audio file External disc control features 20 Playing CD amp Audio file Playing USB iPod device Drive Search Playing External Disc Fast Forwarding and Reversing Music Search Disc Search Folder Album Search Direct Music Search Direct Disc Search prey eee of CD and Audio ile Disc Naming DNPS File Select Text Title Scroll Menu system 26 Menu System Security Code Source Select Mode iPod mode setting Touch Sensor Tone Manual Clock Adjustment Date Mode Date Adjustment Synchronize Clock DSI Disabled System Indicator
26. OFF The built in amplifier deactivates Other than Standby mode When the Dual Zone System is ON Dual Zone System Setting Setting the Front channel and Rear channel sound in the Dual Zone System Display Setting Zone 2 Rear Sub source Auxiliary input source is to be rear channel Zone 2 Front Sub source Auxiliary input source is to be front channel 30 English In Audio file source Supreme Setting When AAC MP3 or WMA files encoded at a low bit rate less than 96kbps fs 44 1k 48kHz are played this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate Processing is optimized for the compression format used AAC MP3 or WMA and adjustment is made for the bit rate used Display Supreme ON Supreme OFF The sound effect may be imperceptible depending on the relationship between the audio file format and setting This function is not available on iPod Setting Plays sound using the Supreme function Plays the original sound stored in the audio file Other than Standby mode B M S Bass Management System Adjust the bass boost level of the external amplifier using the main unit Display Setting AMP Bass Flat Bass boost level is flat AMP Bass 6 Bass boost level is low 6dB AMP Bass 12 Bass boost level is mid 12dB AMP Bass 18
27. ad WV The specified CD is quite dirty ae re Clean the CD V The disc is loaded in a different slot from that specified ts Eject the disc magazine and check the number WV The disc is severely scratched ts Try another disc instead Audio file source H The sound skips when an Audio file is being played VW The media is scratched or dirty ts Clean the media referring to the CD cleaning of eee the section on lt Handling CDs gt page 6 VY The audio file is broken or not supported Sau r Damaged and unsupported files are skipped WY The recording condition is bad ts Record the media again or use another media USB device source H The USB device is not detected V The USB connector is disconnected ts Connect the connector of the USB device properly H The USB device does not play its audio files VW The USB connector is disconnected t Connect the connector of the USB device properly English 43 Troubleshooting Guide The messages shown below display your systems condition Eject No disc magazine has been loaded in the changer The disc magazine is not completely loaded No CD in the unit No disc has been loaded in the disc magazine No Disc No disc has been loaded in the disc magazine The CD is quite dirty The CD is upside down The CD is scratched a lot TOC Error The number of files or folders which are stored in the connected USB device is above the limitation The
28. anual Clock Adjustment gt etc are entered step by Control mode gt page 10 step Three menu items appear on the display The menu item 2 Select the menu item displayed at the center is the one you can adjust Turn the Control knob or push it towards up or down Example When you want to set the beep sound select the Beep display 3 Set the menu item Push the Control knob towards right or left Example When you select Beep each time you push the knob it alternates between Beep ON or Beep OFF Select 1 of them as the setting 26 English In Standby mode Security Code Activating the Security Code disables the usage of audio unit by someone else Once the Security Code is activated the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle Indication of this Security Code activation prevents your precious audio unit from stealing When you activate the Security Code function it cannot be released Note your Security Code is the 4 digit number entered in your Car Audio Passport in this package 1 Enter Standby Press the SRC button Select the STANDBY display Refer to lt Selecting the Source gt page 7 2 Enter Menu mode Using the Control knob select MENU For the operation method refer to lt Function Control mode gt page 10 Security Set is displayed 3 Enter Security Code mode Press the Control knob for at least 1 s
29. ayed In the lower text display part no information is displayed when display without information is selected The text display In Tuner source Information Display Condition Program Service name FM Frequency PS 910 Radio text FM Radio Text 00000 Frequency MW LW Frequency Clock Clock O00000 Date Date O00000 Blank Blank 000 In CD amp External disc source Information Display Condition Disc title Disc Title 00000 Track title Track Title O00000 Track number amp Play time P Time Disc name DNPS O00000 Clock Clock O00000 Date Date O00000 Blank Blank 000 In Audio file source Information Display Condition usic title amp Artist name Title Artist O00000 Album name amp Artist name Abum Artist 0000 Folder name Folder Name OO File name File Name O00000 lay time amp Music number P Time Clock Clock O00000 ate Date 00000 lank Blank 000 In Standby Information Display Condition Standby Source Name Clock Clock O00000 Date Date O00000 Blank Blank 000 In Auxiliary input source Information Display Condition Auxiliary input name Source Name Clock Clock O00000 Date Date O00000 Blank Blank 000 English 13 General features Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with yo
30. connector is linked with the ignition and the A B 2 Purple Black Rear Right 4 pin yellow is connected to the constant power B 3 Gray Front Right supply B 4 Gray Black Front Right Ignition cable Red A 7 Pin Red B 5 White Front Left a 8 PED Nie B 6 White Black Front Left Unit Vehicle B 7 Green Rear Left o gt Battery cable Yellow A 4 Pin Yellow B 8 Green Black Rear Left N The A 7 pin red of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin yellow is linked to the ignition Ignition cable A 7 Pin Red af Unit y a Vehicle gt Ba Battery cable A 4 Pin Yellow Yellow w The A 4 pin yellow of the vehicle s ISO connector is not connected to anything while the A 7 pin red is connected to the constant power supply or both the A 7 red and A 4 yellow pins are connected to the constant power supply Ignition cable Red A 7 Pin Red Bd Unit Re Biaoep Vehicle Battery cable Yellow A 4 Pin Yellow When the connection is made as in 3 above the unit s power will not be linked to the ignition key For that reason always make sure to turn off the unit s power when the ignition is turned off To link the unit s power to the ignition connect the ignition cable ACC red to a power source that can be turned on and off with the ignition key 40 English Installation Re
31. e Display Setting SRC Select 1 Displays source icons for your choice SRC Select 2 Allows you to select sources one after another English 27 Menu system Function of KDC W7537U KDC W7537UY In USB mode with iPod connected iPod mode setting Setting up the iPod operation method in File Select Display Setting iPod Mode ON Uses the operation method similar to that of iPod iPod Mode OFF Uses the operation method different from that of iPod In Standby mode Touch Sensor Tone Setting the operation check sound beep sound ON OFF Display Setting Beep ON Beep is heard Beep OFF Beep canceled In Standby mode Manual Clock Adjustment You can do this adjustment when the lt Synchronize Clock gt page 29 is set as OFF 1 Select Clock Adjustment mode Turn the Control knob Select the Clock Adjust display 2 Enter Clock Adjust mode Press the Control knob for at least 1 second The clock display blinks 3 Selecting the item hours or minutes to adjust Push the Control knob towards right or left The items that are blinking are items that you can adjust 4 Adjust each item Turn the Control knob or push it towards up or down 5 Exit Clock adjustment mode Press the FNC button 28 English In Standby mode Date Mode Setting the date format 1 Select Date Mode Turn the Control knob Select the Date Mode display 2 Enter
32. e Firmware version display Displaying the firmware version with the unit Turn the Control knob Select the F W Version display In Standby mode Demonstration mode Setting Sets the demonstration mode 1 Select the Demonstration mode Turn the Control knob Select the DEMO Mode display 2 Set the Demonstration mode Press the Control knob for at least 2 seconds Each time you press the knob at least 2 seconds the Demonstration mode alternates between the settings shown in the table below Display DEMO Mode ON DEMO Mode OFF Setting The Demonstration mode function is ON Exit Demonstration mode Normal mode English 35 Accessory of KDC W7537UY KDC W7037Y Basic Operations of remote control FM AM g l z 2 ZONE 2 Z0NE a OO 0 19 7 V A Loading and Replacing the battery Use two AA R6 size batteries Slide the cover while pressing downwards to remove it as illustrated Insert the batteries with the and poles aligned properly following the illustration inside the case AWARNING Store unused batteries out of the reach of children Contact a doctor immediately if the battery is accidentally swallowed A Do not set the remote control in hot places such as on the dashboard 36 English DIRECT 10K This button is used when Kenwood Bluetooth HANDS FREE BOX is connected For more information refer to the ins
33. e 10 2 Select the text Turn the Control knob or push it towards left or right See lt The text display gt page 13 Display Type B Information of condition column is displayed Display Type E Information of condition column is displayed 3 Exit Text Dispaly Selection mode Press the Control knob When LX AMP is connected the item setup by the Display mode of LX AMP is displayed When the music number exceeds 1000 only the last 3 digits of its number are displayed KDC W7537U W7537UY Album name cannot be displayed in WMA file KDC W7037 W7037Y usic title Artist name and Album name cannot be displayed in WAV file KDC W7537U W7537UY When playing music from iPod or music edited by Music Editor the folder name display may show something different such as playlist or artist name depending on the music selection procedure KDC W7537U W7537UY In the Display Type B part alternate information is displayed when display without information is selected In the Display Type E part no information is displayed when display without information is selected 12 English Text Display Selection Display Type C amp 2D Changing the text display 1 Enter Text Display Selection mode Using the Control knob select DISP gt TEXT For the operation method refer to lt Function Control mode gt page 10 2 Select the text display part Push the Control knob towards up or down The curs
34. econd When Enter is displayed SECURITY SET is also displayed 4 Select the digits to enter Push the Control knob towards right or left 5 Select the Security Code numbers Turn the Control knob or push it towards up or down 6 Repeat steps 4 and 5 and complete the Security Code 7 Confirm the Security Code Press the Control knob for at least 3 seconds When Re Enter is displayed SECURITY SET is also displayed 8 Do the step 4 through 7 step operation and reenter the security code Approved is displayed The Security Code function activates Ifyou enter a Code different from your Security Code you have to start over from step 4 9 Exit Security Code mode Press the FNC button Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON 2 Do the step 4 through 7 step operation and reenter the security code Approved is displayed Now you can use the unit If an incorrect code is entered Waiting is displayed and the input prohibition periods shown in the table below is generated After the input prohibition time lapses SECURITY SET is displayed and you can reenter the code Number of times the incorrect code was input 1 Input prohibited time 2 5 minutes 3 1 hour 4 24 hours In Standby mode Source Select Mode Setting up the Source Select mod
35. er 12 12 Middle 12 12 Lower 12 12 Text O 12 Display Type A Display Type B Status Setting Determine whether the On and Off statuses of various functions are to be displayed on the Display Type A B 1 Enter Status Setting mode Using the Control knob select DISP gt STATUS For the operation method refer to lt Function Control mode gt page 10 2 Select the Status display Turn the Control knob 3 Exit Status Setting mode Press the Control knob Display Type A Display Type B Graphic Display Selection Changing the graphic Display 1 Enter Graphic Display Selection mode Using the Control knob select DISP gt GRAPH For the operation method refer to lt Function Control mode gt page 10 2 Select the graphic display Turn the Control knob or push it towards left or right Select from the following displays Graphic display Display Movie 1 2 Wallpaper 1 6 Wallpaper scan SCAN 3 Exit Graphic Display Selection mode Press the Control knob The setting of this function is available while TYPE SELECT A TYPE SELECT B is selected for the Display mode English 11 General features Text Display Selection Display Type B amp E Selecting the text display 1 Enter Text Dispaly Selection mode Using the Control knob select DISP gt TEXT For the operation method refer to lt Function Control mode gt pag
36. ess the TI button 3 Select the language Turn the Control knob or push it towards up or down Each time you push the knob the language alternates between the languages shown in the able below Language Display English English Spanish Spanish French French utch Dutch orwegian Norwegian ortuguese Portuguese Swedish Swedish German German 4 Exit Changing Language mode Press the TI button English 19 CD USB device Audio file External disc control features KENWOOD Release button FNC SCAN RDM REP M RDM SRC Control knob S MODE A RDM IN indicator lH TTL ART T ALBUM H Folder number File number Play time Function icon 7 Playing CD amp Audio file When there is no disc inserted 1 Drop open the faceplate Press the Release button 2 Insert a disc 3 Push the faceplate on the left side and return it to its former position A When the faceplate has been dropped open it might interfere with the shift lever or other vehicle function If this happens pay attention to safety and move the shift lever or take an appropriate action to remove the obstacle then operate the unit Do not use the unit with the faceplate in the open condition If it s used in the open position dust can enter the inside part and cause damage For the audio files and discs
37. g no disc names preset Load Discs are being exchanged in the Disc changer Waiting Radio text data is being received Reading IN Blink The unit is reading the data on the disc The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center Protect Blink The speaker wire has a short circuit or touches the chassis of the vehicle and then the protection function is activated Wire or insulate the speaker cable properly and press the reset button If the Protect code does not disappear consult your nearest service center Unsupported File An Audio file is played with a format that this unit can t support eee Copy Protection A copy protected file is played D DEMO MODE Blink The Demonstration mode has been selected The lt Demonstration mode Setting gt page 35 is ON Turn it OFF No Device N A Device The USB device is selected as a source although no USB device is connected gt Change the source to any source other than USB Connect an USB device and change the source to USB again An unsupported USB device is connected gt For the supported USB devices refer to lt http www kenwood com usb gt No Music Data Error 15 USB Error iPod Error USB REMOVE The connec
38. h a name to Internal CD player 10 discs External CD changer player Varies according to the CD changer player Refer to the CD changer player manual You can change the name of a CD by the same operation you used to name it Function of Audio file Text Title Scroll File Select Scrolling the displayed CD text Audio file text or Selecting the music you want to listen to from the MD title device or media being played now Push the Control knob toward up for at least 2 1 Enter File Select mode seconds Turn the Control knob When the lt Display Illumination Control gt page 29 is set 2 Search for music to OFF the display may black out while scrolling Select the category item using the Control knob Operation system for iPod Operation type Operation Movement between Turn the Control knob items Selection of item Press the Control knob Return to previous item Push the Control knob towards up Return to first item Push the Control knob towards up for at least 1 second Operation system for other than iPod Operation type Operation Movement between items Turn the Control knob Selection of item Push the Control knob towards right Selection of item Press the Control knob Push the Control knob towards right urn to previous item Push the Control knob towards left urn to first item Push the Control knob towards left for at least 1 second a
39. hat all wire connections are securely made by inserting jacks until they lock completely If your vehicle s ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a battery wire the power will not be linked with the ignition i e it will not turn on and off along with the ignition If you want to link the unit s power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition key If the fuse blows first make sure that the wires have not caused a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent short circuits also do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may receive damage or fail to work if you share the wires and or ground them to any metal part in the car After the unit is installed check whether the brake lamps indicators wipers etc on the car are working properly If the console has a lid make sure to install the unit so that the faceplate does not hit the lid when closing and opening Mount the unit so that the mounting angle is 30 or less If You Want to Connect iPod f AUX input E s
40. ial thieves Display Setting DSI ON LED flashes DSI OFF LED OFF In Standby mode Selectable Illumination Selecting the button illumination color as green or Set the Display Illumination Control when the lt Demonstration mode Setting gt page 35 is set to OFF When the display is off pressing any key will turn on the display When the display is off you cannot perform any operation except for the following Volume Attenuator Selecting the source Turning off the power During function control such as the Menu System the display stays on In Standby mode Dimmer Dimming this unit s display automatically when the red vehicle light switch is turned ON Display Setting Display Setting Button Red The illumination color is red Dimmer ON The display dims Button Green The illumination color is green Dimmer OFF The display doesn t dim English 29 Menu system In Standby mode Switching preout Alternating the preout between the rear and subwoofer With the subwoofer the sound outputs without being effected by fader control Display Setting SWPRE Rear Rear preout SWPRE Sub W Subwoofer preout In Standby mode Built in Amp Setting Controlling the built in amplifier Turning OFF this control enhances the preout quality Display Setting AMP ON The built in amplifier activates AMP
41. in the memory Press the Control knob 6 Allow the determined number to take effect Press the Control knob 16 English Cancelling the Preset Memory mode Press the FNC button This function can be operated with 1 6 button Press the desired 1 6 button for at least 2 seconds Auto Memory Entry Putting stations with good reception in the memory automatically 1 Select the band for Auto Memory Entry Push the Control knob towards FM or AM 2 Open Auto Memory Entry Press the AME button for at least 2 seconds When 6 stations that can be received are put in the memory Auto Memory Entry closes When the lt AF Alternative Frequency gt page 32 is ON only RDS stations are put in the memory When Auto Memory Entry is done in the FM2 band the RDS stations preset in the FM1 band are not put in the memory Likewise when Auto Memory Entry is done in the FM3 band RDS stations preset in FM1 or FM2 are not put in the memory Preset Tuning Recalling the stations in the memory 1 Select the band Push the Control knob towards FM or AM 2 Enter Preset Tuning Select mode Turn the Control knob 3 Select a desired station in the memory Turn the Control knob 4 Recall the station Press the Control knob Cancelling Preset Tuning Press the FNC button This function can be operated with 1 6 button Press the desired 1 6 button RDS features Tl
42. ish Function of disc changer Audio file Disc Search Folder Album Search Switching between folders albums contained in the disc in the disc changer media or device being played now Push the Control knob towards up or down This function is not available on iPod and the music edited by Music Editor Function of remote control Direct Music Search Doing Music Search by entering the music number 1 Enter the music number Press the number buttons on the remote control You can select Direct music Search up to 999 2 Do music Search Press the kaa or gt gt button Cancelling Direct Music Search Press the gt I button This function is not available on iPod and the music edited by Music Editor Function of disc changers with remote control Direct Disc Search Doing Disc Search by entering the disc number 1 Enter the disc number Press the number buttons on the remote control 2 Do Disc Search Press the FM or AM button Cancelling Direct Disc Search Press the gt I button Play function of CD and Audio file Setting up the Repeat Play and Scan Play 1 Set up the play function Using the Control knob set your desired setup item to On Off For the operation method refer to lt Function Control mode gt page 10 When the play function is urned on ON is displayed Display Icon _ Press button Function
43. ish General features ATT VOL eer uP saam FNC __S MODE Scan ADM e Je ye LE Te Release button FNC SRC Control knob ATT indicator Function icon Power Turning ON the Power Press the SRC button When the power is ON the lt Security Code gt page 27 is displayed as CODE ON or CODE OFF Turning OFF the Power Press the SRC button for at least 1 second Selecting the Source There are two types of source selection methods depending on the setting SRC Select mode 1 1 Press the SRC button 2 Turn the Control knob or push it towards left or right 3 Press the Control knob SRC Select mode 2 Press the SRC button Source required Display Tuner TUNER USB device iPod USB iPod O Compact Disc External disc Optional accessory CD Changer Auxiliary input AUX Auxiliary input Optional accessory AUX EXT Standby Illumination only mode STANDBY Function of KDC W7537U W7537UY When connection of the iPod is recognized the source display changes from USB to iPod Switch between SRC Select mode 1 and 2 in lt Source Select Mode gt page 27 USB iPod source is recognized as CD source on the connected unit English 7 General features Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise
44. ived as monaural Display Setting MONO OFF The monaural reception is OFF MONO ON The monaural reception is ON Auxiliary Input Display Setting amp Disc Naming Selecting the display when alternating to Auxiliary input source For the Disc Naming refer to the lt Disc Naming DNPS gt page 24 1 Select Auxiliary input source Press the SRC button Select the AUX AUX EXT display Refer to lt Selecting the Source gt page 7 2 Enter Menu mode Using the Control knob select MENU For the operation method refer to lt Function Control mode gt page 10 MENU is displayed 3 Select Auxiliary input display setting mode Turn the Control knob Select the Name Set display 4 Enter Auxiliary input display setting mode Press the Control knob for at least 1 second The selected Auxiliary input display is displayed 5 Select the Auxiliary input display Turn the Control knob or push it towards up or down Each time you push the knob the display alternates as listed below AUX AUX EXT DVD PORTABLE GAME VIDEO TV 6 Exit Auxiliary input display setting mode Press the FNC button When operation stops for 10 seconds the name at that time is registered and the Auxiliary input display setting mode closes The Auxiliary input display can be set only when the built in auxiliary input or the auxiliary input of optional KCA S220A is used Function of KDC W7
45. moving the Unit Installation Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw commercially available Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off 1 Refer to the section lt Removing the hard rubber frame gt and then remove the hard rubber frame 2 Drop open the faceplate by pressing the Release button 3 Tighten the screw 2 x 5 mm Accessory and bracket Accessory in the hole shown on the diagram Accessory ED Accessory S 4 Tighten the screw 2 x 5 mm Accessory and bracket Accessory in the hole shown on the diagram Accessor ri y Accessory Never insert the screws in any other screw hole than the one specified If you screw them in another hole it will contact and may cause damage to the mechanical parts inside the unit English 41 Installation Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Access
46. negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not place the faceplate and the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or he possibility of water splashing To prevent deterioration do not touch the terminals of the unit or faceplate with your fingers Do not subject the faceplate to excessive shock as it is a piece of precision equipment e When replacing a fuse only use a new fuse with he prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction Do not apply excessive force to the open faceplate or place objects on it Doing so will cause damage or breakdown Use only the screws provided or specified for installation If you use wrong screws you could damage the unit Attach the panel while you are on the vehicle The panel lock arm appears when the panel is removed Therefore the panel must be attached while the electrical system of the car is operating Do Not Load 8 cm 3 in CDs in the CD slot If you try to load a 8 cm 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit About CD players disc changers connected to this unit enwood disc changers CD players released in 1998 or la
47. ofer phase gt Low pass filter is set to Through lt Audio Setup gt page 8 1 Cannot select the output destination of the subsource in the Dual zone Cannot adjust the volume of the rear speakers P The Dual zone function is disabled lt Audio Setup gt page 8 Hi No Audio control effect on AUX P The Dual zone function is enabled lt Audio Setup gt page 8 1 e Cannot register a security code Cannot set up Display Illumination Control P lt Demonstration mode Setting gt page 35 is not turned off Hi Cannot set up the Power off timer gt lt Security Code gt page 27 is not set a Cannot play audio files gt lt CD Read Setting gt page 34 is set to 2 Hi Cannot File select e Cannot direct music serch P The Random play function is enabled What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General Edthe Touch Sensor Tone doesn t sound VW The preout jack is being used ts The Touch Sensor Tone can t be output from the preout jack Tuner source H Radio reception is poor V The car antenna is not extended W The antenna control wire is not connected t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt page 39 Disc source H The specified disc does not play but another one plays inste
48. or P moves to the selected text display part Select the text Turn the Control knob or push it towards left or right See lt The text display gt page 13 Upper text display part Information of condition column is displayed Middle text display part Information of condition column is displayed Lower text display part Information of condition column is displayed 3 Exit Text Display Selection mode Press the Control knob When LX AMP is connected the item setup by the Display mode of LX AMP is displayed en the music number exceeds 1000 only the last digits of its number are displayed KDC W7537U 7537UY bum name cannot be displayed in WMA file KDC W7037 W7037Y Music title Artist name and Album name cannot be displayed in WAV file KDC W7537U W7537UY When playing music from iPod or music edited by Music Editor the folder name display may show something different such as playlist or artist name depending on the music selection procedure KDC W7537U W7537UY Same information cannot be displayed in Upper text display part Middle text display part and Lower text display part However the blank display is able to have multiple selections In the upper text display part alternate information is displayed when display without information is selected bevs In the middle text display part the Kenwood logo is displayed if the contents of the information cannot be displ
49. or during conversation E SI To connect the Kenwood navigation system consult your navigation manual If no connections are made do not let the wire come out from the tab Power control Motor antenna control wire Blue White Connect either to the power control terminal P CONT 3 a l when using the optional power amplifier or to the TANT CONT antenna control terminal in the vehicle e 4 Battery wire Yellow Ignition wire Red lt em lt m0 See next page A 7 Pin Red A 4 Pin Yellow Connector A Connector B English 39 Connecting Wires to Terminals Connector Function Guide AWARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on External Power he type of vehicle you drive Make sure to make the proper Connector connections to prevent damage to the unit AA Yellow Battery The default connection for the wiring harness is described in Ae we ows Control 1 below If the ISO connector pins are set as described in 2 z Sie ite ee or 3 make the connection as illustrated AB Black Earth Ground Please be sure to reconnect the cable as shown 2 below to C install this unit to the Volkswagen vehicles etc onnection Speaker Connector 1 Default setting The A 7 pin red of the vehicle s B 1 Purple Rear Right ISO
50. ory Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner Removing the Unit 1 Refer to the section lt Removing the hard rubber rame gt and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards he inside Screw M4X8 commercially available Accessory Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it 42 English Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit 1 Cannot switch to Aux source P AUX is not turned on 1 lt Built in Auxiliary input Setting gt page 34 AUX cannot be used when the KCA iP200 is connected 1 Cannot set up the subwoofer Cannot set up subwoofer phase No output from the subwoofer Cannot set up the low pass filter gt lt Subwoofer Output gt page 9 is not set to On The Dual zone function is enabled lt Audio Setup gt page 8 1 Cannot set up the high pass filter Cannot set up the Fader P The Dual zone function is enabled lt Audio Setup gt page 8 a Cannot set up the subwo
51. parately Set up the channel of sub source by lt Dual Zone System Setting gt page 30 Select Main source by SRC button Adjust the volume of Front channel by VOL knob Adjust the volume of Rear channel by lt Audio Control gt page 8 The Audio Control has no effect on sub source You can use the Dual Zone System with the internal auxiliary input 5 Exit Audio Setup mode Press the VOL knob for at least 1 second Speaker Setting Fine tuning so that the System Q value is optimal when setting the speaker type 1 Enter Standby Press the SRC button Select the STANDBY display Refer to lt Selecting the Source gt page 7 2 Enter Speaker Setting mode Press the VOL knob SP SEL is displayed 3 Select the Speaker type Turn the VOL knob Each time you turn the knob the setting alternates between the settings shown in the table below Speaker type Display OFF OFF For 5 amp 4 in speaker 5 4inch For 6 amp 6x9 in speaker 6x9 6inch For the OEM speaker QEM 4 Exit Speaker Setting mode Press the VOL knob Subwoofer Output Turning the Subwoofer output ON or OFF Push the Control knob toward down for at least 2 seconds Each time you push the knob Subwoofer output switches ON and OFF When it is ON SUB WOOFER ON is displayed TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The a
52. r 1 pair of Audio Preset Memory You cannot register by the source When you press the Reset all the sources will be the setting value which is registered The following items cannot be registered Volume Balance Fader Loudness Volume offset Dual Zone System Rear Volume Other than Standby mode Audio Preset Recall Recalling the sound setup registered by lt Audio Preset Memory gt page 34 1 Select the source Press the SRC button Refer to lt Selecting the Source gt page 7 2 Enter Menu mode Using the Control knob select MENU For the operation method refer to lt Function Control mode gt page 10 MENU is displayed 3 Select Audio Preset mode Turn the Control knob Select the Audio Preset display 4 Enter Audio Preset mode Press the Control knob for at least 1 second 5 Select the Audio Preset Recall Turn the Control knob Select the Recall display 6 Determine whether to recall the Audio Preset Press the Control knob Recall is displayed 7 Recall the Audio Preset Select Yes using the Control knob Recall Completed is displayed 8 Exit Audio Preset mode Press the FNC button The User memory of SYSTEM Q in lt Audio Control gt page 8 is changed to the value which was recalled The source tone memory item of lt Audio Control gt page 8 is changed to the value which was recalled by the selected source Function of KDC W7537U KDC W7537UY In Standby mod
53. rol knob towards ka a or gt gt English 17 RDS features PTY Program Type Selecting the Program Type and searching for a station 1 Enter PTY mode Press the Control knob During PTY mode the PTY indicator is ON This function cannot be used during a traffic bulletin or AM reception 2 Select the Program Type Turn the Control knob or push it towards up or down Each time you push the knob the Program Type alternates between program types shown in the able below No Program Type Display Speech All Speech 2 usic All Music 3 ews News 4 Current Affairs Current Affairs 5 information Information 6 Sport Sport 7 Education Education 8 rama Drama 9 Culture Cultures 0 Science Science 1 Varied Varied Speech 2 op Music Pop Music 3 ock Music Rock Music 4 Easy Listening Music Easy Listening M 5 Light Classical Light Classic M 6 Serious Classical Serious Classics 7 Other Music Other Music 8 Weather Weather amp Metr 9 Finance Finance 20 Children s programs Children s Prog 21 Social Affairs Social Affairs 22 eligion Religion 23 hone In Phone In 24 rave Travel amp Touring 25 Leisure Leisure amp Hobby 26 azz Music Jazz Music 27 Country Music Country Music 28 ational Music National Music 29
54. s the power OFF after 20 minutes Power OFF 40min Turns the power OFF after 40 minutes Power OFF 60min Turns the power OFF after 60 minutes In Standby mode CD Read Setting When there is a problem with playing a CD with special format this setting plays the CD by force Display Setting CD Read 1 Play CD and Audio file CD Read 2 Play CD by force Some music CDs may not play even in the CD Read 2 mode 34 English Other than Standby mode Audio Preset Memory Registering the value setup by Sound Control The memory cannot be erased by the Reset button 1 Setup Sound Control Refer to the following operations to setup the Sound Control lt Audio Control gt page 8 lt Audio Setup gt page 8 2 Enter Menu mode Using the Control knob select MENU For the operation method refer to lt Function Control mode gt page 10 MENU is displayed 3 Select Audio Preset mode Turn the Control knob Select the Audio Preset display 4 Enter Audio Preset mode Press the Control knob for at least 1 second 5 Select the Audio Preset Memory Turn the Control knob Select the Memory display 6 Determine whether to put the Audio Preset in the memory Press the Control knob Memory is displayed 7 Put the Audio Preset in the memory Select Yes using the Control knob Memory Completed is displayed 8 Exit Audio Preset mode Press the FNC button Registe
55. ted USB device contains no playable audio file Media was played that doesn t have data recorded that the unit can play The connected USB device is rated a current capacity higher than the allowable limit gt Check the USB device with reference to lt http www kenwood com usb gt Some trouble may have occurred to the connected USB device gt Change the source to any source other than USB Remove the USB device Connection to the iPod has failed Remove the USB device and then reconnect it Confirm that the software for the iPod is the latest version The Remove mode has been selected for the USB device You can remove the USB device safely English 45 Specifications Specifications subject to change without notice FM tuner section Frequency range 50 kHz space 87 5 MHz 108 0 MHz Usable sensitivity S N 26dB 0 7 uV 750 Quieting Sensitivity S N 46dB 21 6 uV 750 Frequency response 3 0 dB 30 Hz 15 kHz Signal to Noise ratio MONO 65 dB Selectivity DIN 400 kHz gt 80 dB Stereo separation 1 kHz 35 dB MW tuner section Frequency range 9 kHz space 531 kHz 1611 kHz Usable sensitivity S N 20dB 25 uV LW tuner section Frequency range 153 kHz 281 kHz Usable sensitivity S N 20dB 745 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed
56. ted lastly for Bass level Middle level and Treble level are recalled automatically 5 Exit Audio Control mode Press any button Press a button other than the VOL knob and ATT button Audio Setup Setting the Sound system such as Cross over Network 1 Select the source to adjust Press the SRC button Refer to lt Selecting the Source gt page 7 2 Enter Audio Setup mode Press the VOL knob for at least 1 second 3 Select the Audio Setup item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Setup the Audio item Turn the VOL knob Adjustment Item _ Display Range Front High Pass Filter HPF F Fc Through 40 60 80 100 120 50 180 220 Hz Rear High Pass Filter HPF R Fc Through 40 60 80 100 120 150 180 220 Hz Low Pass Filter LPF SW Fc 50 60 80 100 120 Through Hz Subwoofer Phase SW PHASE Reverse 180 Normal 0 Volume offset VOL OFFSET 8 0 AUX 8 8 Loudness LOUD OFF ON Dual Zone System 2 ZONE OFF ON Volume offset Sets each source s volume as a difference from the basic volume Loudness Compensates for low and high tones during low volume Only the low tone is compensated for when the tuner is selected as a source Dual Zone System Main source and sub source Auxiliary input output Front channel and Rear channel se
57. ter can be connected to this unit Refer to the catalog or consult your Kenwood dealer or connectable models of disc changers CD players ote that any Kenwood disc changers CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit Connecting unsupported disc changers CD players to his unit may result in damage Set the O N Switch to the N position for the applicable Kenwood disc changers CD players he functions you can use and the information that can be displayed may differ depending on the models being connected AN You can damage both your unit and the CD changer if you connect them incorrectly Lens Fogging When you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging this condensation on the lens may not allow CDs to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer iPod is a trademark of Apple Computer Inc registered in the U S and other countries The AAC logo is trademark of Dolby Laboratories English 3 Notes If you experience problems during installation consult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they work with your model and in your area
58. truction manual of Bluetooth HANDS FREE BOX Basic operations VOL buttons Adjusts the volume SRC button Each time you press the button the source alternates For the source alternating order refer to lt Selecting the Source gt page 7 ATT button Turns the volume down quickly When the button is pressed again the volume returns to the previous level Audio Control AUD button Selects the Audio item to be adjusted VOL buttons Adjusts the Audio item Refer to lt Audio Control gt page 8 for the operation method such as the procedures for Audio control and others operations Dual Zone System 2 ZONE button Each time you press the button 2 ZONE of lt Audio Setup gt page 8 is turned ON or OFF A V buttons Adjusts the volume of the rear channel The rear channel activates while the Dual Zone System is ON In Tuner source FM AM buttons Selects the band Each time you press the FM button the band alternates between the FM1 FM2 and FM3 bands lt gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations DIRECT button Enters and cancels the lt Direct Access Tuning gt page 16 mode gt I button Enters and cancels the lt PTY Program Type gt page 18 mode In Disc USB source lt gt gt buttons Going forwards and backwards between music buttons Going forwards
59. u helping to deter theft Removing the Faceplate 1 Press the Release button Drop open the faceplate 2 Drawing the faceplate to left side pull it to forward and remove it The faceplate is a precision piece of equipment and can be damaged by shocks or jolts Keep the faceplate in its faceplate case while detached Do not expose the faceplate and the faceplate case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Faceplate 1 Align the shaft on the unit with the depression on the faceplate 2 Push the faceplate in until it clicks The faceplate is locked in place allowing you to use the unit 14 English External Display Selection Changing the display in the connected External Display 1 Enter External display select mode Using the Control knob select DISP gt DOUT For the operation method refer to lt Function Control mode gt page 10 DISP Out Select is displayed 2 Select the display Turn the Control knob or push it towards left or right Select your desired display 3 Exit display control mode Press the Control knob Tuner features AME FNC 1 6 SRC Control knob Band display Preset station number Frequency display Function icon Tuning Selecting the station 1 Select tuner source Press the SRC button Select the TUNER
60. udio system pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON To use the TEL Mute feature you need to hook up the MUTE wire to your telephone using a commercial telephone accessory Refer to lt Connecting Wires to Terminals gt page 39 English 9 General features Function Control mode To set up various functions of this unit select tree structured function items 1 Enter Function Control mode Press the FNC button 2 Select your desired setup item Select a setup item using the Control knob Operation type Operation Movement between Turn the Control knob items Selection of item Press the Control knob Return to previous item Press the FNC button Functions of items are as follows Display Icon Function of setup item Menu MENU Allows you to set up the environment Refer to lt Menu system gt page 26 isplay Select DISP Allows you to set up the display Refer to page 10 to page 13 reset Memory PMEM Allows you to put stations in the memory Refer to lt Station Preset Memory gt page 16 File Scan etc SCAN Allows you to set how to play the CD and etc audio file Refer to lt Play function of CD and Audio file gt page 23 Return geal
61. ulti Card Readers with a maximum of 4 slots Ifa device is inserted during connection of the Multi Card Reader it is not recognized Select the Remove mode with reference to lt Playing USB iPod device gt page 21 remove the Card Reader and then insert the memory English 21 CD USB device Audio file External disc control features Playing External Disc Playing discs set in the optional accessory disc player connected to this unit Press the SRC button Refer to lt Selecting the Source gt page 7 Select the display for the disc player you want Display examples Display Disc player CD Changer CD changer MD Changer MD changer Pause and play Press the Control knob Each time you press the knob the audio pauses or plays The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected Fast Forwarding and Reversing Fast Forwarding Hold down toward gt gt with the Control knob Release to resume the playback Reversing Hold down toward ka a with the Control knob Release to resume the playback There is no sound while the Audio file is being searched You cannot fast Forwarding and Reversing while AAC file is being played KDC W7037 W7037Y Music Search Switching between music contained in the disc or folder being played now Push the Control knob towards a a or gt gt 22 Engl
62. without displaying older name etc Changing the browse item will display a correct title etc When the iPod is connected to this unit KENWOOD or is displayed on the iPod to indicate that you cannot operate the iPod When the USB device is connected to this unit it can be charged up provided that this unit is powered When the Multi Card Reader is used refer to lt Drive Search gt page 21 After you stopped playing a file contained in the USB device you can restart playing the file from the point where you stopped its playback Even after removing the USB device you can restart playing the file from the point where you stopped its playback as long as the files contained in the USB device are all the same Be sure to insert the USB device connector as far as it will go o Pause and play Press the gt I button Each time you press the knob the audio pauses or plays Removing the USB device 1 Drop open the faceplate Press the Release button 2 Set the remove mode as the USB source Press the 4 button for at least 2 seconds The 4 indicator blinks 3 Remove the USB device Function of KDC W7537U KDC W7537UY Drive Search Selecting the device inserted in the Multi Card Reader 1 Put the playback to pause Press the S MODE button 2 Select a device Push the Control knob towards up or down 3 Restart playback Press the Control knob This unit is compliant with M
63. you can play with this unit refer to lt About Audio file gt page 5 When a disc is inserted the IN indicator is ON 20 English When a disc is inserted Press the SRC button Select the Compact Disc display Refer to lt Selecting the Source gt page 7 Pause and play Press the Control knob Each time you press the knob the audio pauses or plays Eject the disc 1 Drop open the faceplate Press the Release button 2 Eject the disc Press the 4 button 3 Press the faceplate on the left side and return it to its former position You can eject the disc for 10 minutes after switching off the engine Function of KDC W7537U KDC W7537UY Playing USB iPod device When the USB device is not connected Connect the USB device Playback of the file contained in the USB device starts When the USB device is connected Select USB source Press the SRC button Select the USB or iPod display Refer to lt Selecting the Source gt page 7 For the audio files that can be played with this unit and the devices that can be connected to this unit refer to lt About Audio file gt page 5 The word iPod appearing in this manual indicates the iPod connected with the KCA iP200 optional accessory Refer to lt About Audio file gt page 5 Ifyou start playback after connecting the iPod the music that has been played by the iPod is played first In this case RESUMING is displayed

Kenwood KDC-W7037Y Car Stereo System User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents