Home

Kenwood KDC-PSW9527 Car Stereo System User Manual

1. Panel Control 1 No angle can be adjusted if the panel position has been set to its most end position Also if you have set the angle below the horizontal position the angle is set to horizontal when you set the panel to its most end position The angle can be adjusted regardless of the panel position Panel Control 2 Function of the KDC W8027 System Q Setting Setting whether the display indicates the System Q factors Bass center frequency Bass Q factor Bass extend Middle center frequency Middle Q factor and Treble center frequency in Audio control Display System Q ON System Q OFF Setting The System Q factors are displayed The System Q factors aren t displayed Function of the KDC PSW9527 KDC W9027 Audio Setup Switches between the Easy mode and PRO mode for detailed setup during Audio setup Display Setting Audio Setup Easy Selects the quick Audio setup Audio Setup PRO Selects the detailed Audio setup Display Setting AMP Mute OFF The built in amplifier activates AMP Mute ON The built in amplifier deactivates B M S Bass Management System Adjust the bass boost level of the external amplifier using the main unit Display Setting AMP Bass Flat Bass boost level is flat AMP Bass 6 Bass boost level is low 6dB AMP Bass 12 Bass boost level is mid 12dB AMP Bass 18 Bass boost level is high
2. Function of MP3 WMA Folder Select Quickly selecting the folder you want to listen to 1 Select the key function section Press the NEXT button Repeatedly press the button until FSEL is displayed above the 5 button Refer to Notes on Multi function Key System page 10 2 Enter Folder Select mode Press the 5 FSEL button FOLDER SELECT is displayed During Select mode the folder information is displayed as shown below Folder name display Displays the current folder name I ERIT HOME Folder number display Displays the number in the folder belonging to the currently selected folder 3 Select the folder level Press the FM or AM button With the FM button you move 1 level down and with the AM button 1 level up Selecting a folder in the same level Press the ka a or gt gt button With the lt lt button you move to the previous folder and with the gt i button to the next folder Returning to the top level Press the 4 HOME button Scrolling the folder name display Press the SCRL button 4 Decide the folder to play Press the 2 OK button The Folder Select mode releases and the MP3 WMA in the folder being displayed is played The methods for moving to other folders in the folder select mode are different from those in the folder search mode See Notes on playing MP3 WMA page 8 for details Canceling the Folder Select mode Press the 3 E
3. Y You re trying to enter a frequency with a 0 01 MHz unit ts What can be designated in the FM band is to 0 1 MHz It isn t the set Traffic information sound volume The set sound volume is less than the tuner sound volume f the tuner sound volume is louder than the set sound volume the tuner sound volume is used The disc won t insert WV There s already another disc inserted t Press the button and remove the disc Direct Search can t be done Another function is ON ts Turn Random Play or other functions OFF Track Search can t be done V For the discs folders first or last song For each disc folder Track Search can t be done in the backward direction for the first song or in the forward direction for the last song English 63 Troubleshooting Guide MP3 WMA source Cannot play an MP3 WMA The media is scratched or dirty te Clean the media referring to the CD cleaning of the section on About CDs page 7 The sound skips when an MP3 WMA is being played The media is scratched or dirty ts Clean the media referring to the CD cleaning of the section on About CDs page 7 The recording condition is bad ts Record the media again or use another media The MP3 WMA track time isn t displayed correctly VW te There are times when it isn t displayed correctly according to the MP3 WMA recording conditions
4. To EXT AMP CONT terminal of the amplifier having the external amp control function Connect to the terminal that is grounded when either the telephone rings or during conversation To connect the KENWOOD navigation system consult your navigation manual Connect either to the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Yellow Blue White Orange White Red Black Battery Power Control Dimmer Ignition ACC Earth Ground Connection Purple Purple Black Gray Gray Black White White Black Green Green Black Rear Right Rear Right Front Rig Front Rig Front Le Front Le Rear Le Rear Le AAWARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive Make sure to make the proper connections to prevent damage to the unit The default connection for the wiring harness is described in 1 below If the ISO connector pins are set as described in 2 or 3 make the connection as illustrated lease be sure to reconnect the cable as shown 2 below o install this unit to the Volkswagen vehicles etc Default setting The A 7 pin red of the vehicle s ISO connector is linked with
5. 2 Remove the Backpanel forward When DSI Disabled System Indicator page49 is set to ON DSI blinks The back panel is a precision piece of equipment and can be damaged by shocks or jolts For that reason keep the back panel in its special storage case while detached Do not expose the Backpanel or its storage case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Backpanel 1 Set the Backpanel to the panel bracket 2 Hold down on the Backpanel until it is locked 20 English TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The audio system pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON Function of the KDC W8027 System Q You can recall the best sound setting preset for different types of music 1 Select the source to set Press the SRC button 2 Select the Sound type Press the Q button Each time the button is pressed the sound setting switches Sound setting Display SRS WOW SRS WOW Natural Natural User memory USER Rock ROCK Pops POPS Easy EASY Top 40 TOP 40 Jazz JAZZ User memor
6. 3 Select the cabin size of your car Press the kaa or gt gt button 4 Select a speaker Press the 3 SP SEL button 5 Set up the speaker Press the 2 5 button For the speakers you can set up using buttons 2 to 5 see the Audio setup Easy mode page 28 6 Select the speaker size Press the ka or gt gt button 7 Exit Audio setup mode Press the 6 RTN button Now you can create the best sound field to your car For the detailed speaker setup see the Audio Setup PRO mode page 30 English 11 General features ATT 1 6 NEXT SRC VOL Q gt i L AM FM maa gt gt SCRI NAME S SW iPS KENWOOD KENWOOD f 1 Wwe Power Hiding the control panel sms Press the SRC button for at least 1 second Turning ON the Power When the time set in OFF Wait Time Setting Turn the vehicle ignition ON page 49 lapses the panel is hidden and the The panel appears power turns OFF Showing the control panel When the power is ON the Security Code page 46 Press the left part at the lower side of the is displayed as CODE ON or CODE OFF panel Turing OFF the Power Turn the vehicle ignition OFF or press the SRC button for at least 1 second The panel hides A Do not apply force to the panel during operation It can cause damage The panel is opened to enable the operation
7. 2 5 button is pressed the adjustable audio items are switched among ranges of all stage section s tables on the ollowing pages 1st section Multi function key operation Audio control item 2 PLII Dolby ProLogic II setting 3 WOW SRS WOW setting 4 OFF OFF setting 5 FINE 2 PNRM Panorama setting 3 DIM Dimension control 4 CT WDTH Center width control 2 FOCUS FOCUS setting 3 TruBass F SRS TruBass Front setting 3 TruBass R SRS TruBass Rear setting 4 SRS 3D SRS 3D setting amp When you select the MUSIC using PLII you can set the PNRM DIM and CT WDTH using the FINE function Also when you select the WOW you can set the FOCUS TruBass F TruBass R and SRS 3D using the FINE function 2 PLII MUSIC Music 5 FINE MOVIE Movie 9 PNRM MATRIX Matrix 3 DIM 4 CT WDTH 3 WOW 5 FINE LOW Low 2 FOCUS MIDDLE Middle 3 TruBass F HIGH High 3 TruBass R USER User 4 SRS 3D 2nd section Multi function key operation Audio control item 2 POSI Position setting 3 BL F 3 BL Balance setting 3 F Fader setting 4 VOFF Volume offset 5 Sw 5 SW LEVEL Subwoofer level 5 PHASE Subwoofer Phase setting Volume offset Each source s volume can be set as a difference from the basic volume _ You can control this item when
8. 2 BASS EQ Front Bass setting EQ 3 MID EQ Front Middle setting 4 TRE EQ Front Treble setting 3 REAR 2 BASS EQ Rear Bass setting 3 MID EQ Rear Middle setting 4 TRE EQ Rear Treble setting 4 CNTR 2 BASS EQ Center Bass setting 3 MID EQ Center Middle setting 4 TRE EQ Center Treble setting 5 2 FRONT 2 Front L SP LEV Front Left Sp 2 Front R SP LEV Front Righi LEV B REAR 3 Rear L SP LEV Rear Left 3 Rear R SP LEV Rear Right 4 CT SW 4 Center SP LEV Center 4 Sub Woofer SP LEV Subwoofer i 5 T TONE SP LEV Test tone The followings can be adjusted each time button 2 BASS button 3 MID or button 4 TRE of EQ functions is pressed 2 BASS BASS F Bass Center Frequency BASS L Bass Level BASS Q Bass Q Factor 3 MID MID F Middle Center Frequency MID L Middle Level MID Q Middle Q Factor 4 TRE TRE F Treble Center Frequency TRE L Treble Level TRE Q Treble Q Factor You can listen to the T TONE when you have tuned it The sound level is reduced when T TONE is selected The sound returns to the normal level when the original source is selected X over Crossover Network Setup You can manually set a crossover frequency of speakers DIA Digital Time Alignment Manually set the sound output timing of each channel EQ Equalizer You can manually set the equalizer curve SP LEV
9. If the following situations consult your nearest service center Even though the disc changer is connected the Disc Changer source is not ON with AUX EXT showing in the display during the Changer Mode 64 English The messages shown below display your systems condition Eject No Disc TOC Error E 05 Blank Disc No Track Disc E 15 No Music Data No Panel Mecha Error o disc magazine has been loaded in the changer The disc magazine is not completely loaded gt Load the disc magazine properly o CD in the unit Insert the CD o disc has been loaded in the disc agazine Load a disc into the disc magazine a3 o disc has been loaded in the disc agazine Load a disc into the disc magazine he CD is quite dirty The CD is upside own The CD is scratched a lot Clean the CD and load it correctly 3233 an The CD is upside down Load the CD correctly othing has been recorded on the MD o tracks are recorded on the MD though it has a title o edia was played that doesn t have data recorded that the unit can play Use media that has data recorded that the unit can play edia was played that doesn t have data recorded that the unit can play Use media that has data recorded that the unit can play Files for picture downloading only are recorded in CD R CD RW The faceplate of the slave unit being connected to this unit ha
10. MEMORY display blinks 1 time USER The values are erased from memory if the battery is removed or if the reset button is pressed INST The values are held in memory even if the battery is removed or if the reset button is pressed 10 Exit Audio Setup mode Press the 6 RTN button English 31 Function of the KDC PSW9527 KDC W9027 Sound management features Audio Setup memory Recall 1 Enter Audio Setup mode Press the 3 AD SET button 2 Select the Recall section Press the NEXT button Repeatedly press the button until CALL is displayed above the 3 5 button 3 Call the Audio setup memory and select an item to call the memory value Press the 3 5 CALL button If you have set the Audio Setup to Audio Setup PRO using Audio Setup page 50 press button 3 If you have set the Audio Setup to Audio Setup Easy press button 5 4 Recalls the value from memory Press the 2 USER 3 INST button 5 Exit Audio Setup mode Press the 6 RTN button 32 English Tuner features NEXT SRC As N THCLOSE OFF scnl MNAVES BSW DISC TELL Preset station 76 MENU Band display number ips tM 3ch wW 3 Tuning Selecting the station 1 Select tuner source Press the SRC button Select the TUNER display 2 Select the band Press the FM or AM button Each time the FM button is pressed it s
11. pressing the four corners of the hard rubber frame at the same time Do not apply strong pressure to other sections than the corners otherwise troubles such as the impossibility of opening or closing the panel may result The hollow at the center of the rubber frame is designed to make it easier to remove discs If you do not want the hollow to be visible mount the rubber frame in the opposite direction with the flat side at the top instead of the bottom 60 English Locking the Backpanel to the unit If you want to fasten the faceplate to the main unit so that it does not fall off 1 Refer to the Removing the Backpanel function of the section on Theft Deterrent Panel page 20 and remove the Backpanel 2 Insert the panel lock screws into the holes at the sides of the panel Accessory 3 Reattach the Backpanel A Never insert the panel lock screws in any other screw holes than the one specified If you insert them in another hole it will contract and may cause damage to the mechanical parts inside the unit Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Accessory Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner Removi
12. Manual scrolling is possible with l lt lt 4 gt bI and when the setting is set to Auto scrolling is automatic Switching between the Name and Telephone Number Press the TI button Scrolling the Name and Telephone Number display Press the SCRL button 6 Exit Hands Free mode Press the 6 RTN button When New Message is Received New Message is displayed Phone Book Message SMS data synchronize Synchronizing the data in this unit with the data in the GSM telephone 1 Select the key function section Press the NEXT button Repeatedly press the button until SYNC is displayed above the 3 KDC W8027 4 KDC PSW9527 W9027 button Refer to Notes on Multi function Key System page 10 2 Synchronize the data Press the 3 4 SYNC button The GSM Memory SYNC display turns off when data synchronization starts English 45 Menu system SRC yr TP MENU FM mea gt gt Menu display CEE Menu System 4 Exit Menu mode Setting during operation beep sound etc Press the MENU button functions The Menu system basic operation method is When other items that are applicable to the basic explained here The reference for the Menu items operation method above are displayed afterwards and their setting content is after this operation their setting content chart is entered Normally the explanation uppermost setting in the chart is
13. button Enters and cancels the DNPP Disc Name Preset Play page 42 mode 0 9 buttons When in Direct Track File Search page 39 and Direct Disc Search page 39 enter the track file disc number 56 English GSM Hands Free Unit operations H gt gt buttons Switching the display FM AM buttons Switching the initials and messages 0 9 x buttons When in Direct Dial page 44 enter the telephone number E button Entering and switching the Hands Free mode Press the button for at least one second to dial a phone number or to hang up Accessories Installation Procedure Accessories Installation Procedure 1 To prevent short circuits remove the key from the ignition and disconnect the terminal of the battery 2 Make the proper input and output wire connections for each unit 3 Connect the wire on the wiring harness 4 Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle 5 Take Connector A on the wiring harness and connect it to the external power connector on your vehicle 6 Connect the wiring harness connector to the unit 7 Install the unit in your car 8 Reconnect the terminal of the battery 9 Turn the vehicle s ignition key on and open the panel 10 Press the 5 button and the reset button A If your car is not prepare
14. examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may represent something impossible in actual operation Lens Fogging Right after you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging CDs may be impossible to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer English 5 Notes Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe neutral detergent off Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a dry soft cloth Cleaning the CD Slot As dust tends to accumulate in the CD slot clean it every once in a while Your CDs can get scratched if you put them in a dusty CD slot WOW S
15. format not quick format o prevent malfunction Acceptable medium formats The following formats are available for the media used in this unit The maximum number of characters used for file and folder name including he delimiter and three character extension are indicated in parentheses ISO 9660 Level 1 12 characters ISO 9660 Level 2 31 characters Joliet 64 character KDC W8027 Up to 32 characters are displayed Romeo 128 character KDC W8027 Up to 64 characters are displayed Long file neme 200 characters KDC W8027 Up to 64 characters are displayed 64 KDC W8027 Joliet Up to 32 characters are displayed For a list of available characters see the instruction manual of the writing software and the section Entering file and folder names below The media reproducible on this unit has the following limitations Maximum number of directory levels 8 Maximum number of files per folder 255 Maximum number of folders KDC PSW9527 W9027 100 KDC W8027 50 Maximum number of files and folders KDC W8027 512 MP3 WMA written in the formats other than the above may not be successfully played and their file names or folder names are not properly displayed 8 English aximum number of characters for folder name Settings for your MP3 WMA encoder and CD writer Do the following setting when compressing audio data in MP3 WMA data with the MP3 WMA encoder Transfer bit rat
16. frequency is displayed instead Changing the display order Press the ka a or gt gt button Changing the displayed band Press the FM or AM button 2 If the station you want is displayed Press the OK button on the remote The station for the program service name being displayed is received Canceling the SNPP mode Press the DNPP button on the remote RDS features 1 6 M MENU SHAVES wsW DISC Radio text Traffic Information Switching to traffic information automatically when a traffic bulletin starts even when you aren t listening to the radio Press the TI button Each time the button is pressed the Traffic Information function turns ON or OFF When it s ON Traffic Info Announcement is displayed When a traffic bulletin starts Traffic Info Announcement is displayed it and it switches to traffic information During reception of an AM station when the Traffic Information function is turned ON it switches to an FM station During reception of traffic information the adjusted volume is automatically remembered and the next time it switches to traffic information it s automatically the remembered volume THT SCRL AM FM maa gt gt Frequency display Radio Text Scroll Scrolling the displayed radio text Press the SCRL button English 35 RDS features PTY Program Type Selecting the Program Type and searching for
17. in 1997 or earlier and disc changers made by other makers cannot be connected to this unit Unsupported connection may result in damage Setting the O N Switch to the N position for the applicable KENWOOD disc changers CD players The functions that can be used and the information hat can be displayed will differ depending on the models being connected AN You can damage both your unit and the CD changer if you connect them incorrectly LX bus connection The LX AMP and the sensor unit cannot be connected simultaneously You must connect any of them at a time The power supply does not turn ON if you have connected both of them Do Not Load 8 cm 3 in CDs in the CD slot If you try to load a 8 cm 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit NOTE If you experience problems during installation consult your Kenwood dealer If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed If the unit still fails to operate properly after the Reset button has been pressed contact your local KENWOOD dealer for assistance Press the reset button if the disc auto changer fails to operate correctly Norma restored operation should be Reset button The illustrations of the display and the panel appearing in this manual are
18. method Refer to the URL http www kenwood net disp com and rewrite the CD R CD RW When LX AMP unit connecting AMP Control You can control the LX AMP connected to the unit 1 Select AMP Control mode Press the FM or AM button Select the AMP Control display 2 Enter AMP Control mode Press the ka a or gt gt button for at least 1 second 3 Select the AMP Control item for adjustment Press the FM or AM button For the details of the AMP Control item see the Instruction manual attached to the LX AMP 4 Adjust the AMP Control item Press the ka a or gt gt button 5 Exit AMP Control mode Press the MENU button You cannot use the LX AMP operation during standby mode English 53 Menu system Rotary volume operation select Various items can be set using the rotary volume knob Display Setting Rotary SEL ON The rotary volume knob can be used for item setup Rotary SEL OFF The rotary volume knob cannot be used for item setup To use the rotary volume knob for item setup select Rotary SEL ON and press the 1 button in each setup mode 54 English Basic Operations of remote FM AM DISC DISC 0 9 En i e ANG ATT SRC Loading and Replacing the battery Use one lithium battery CR2025 Insert the batteries with the and poles aligned properly following the illustration inside the case Q Keep
19. month or year to adjust Press the ka a or gt gt button The items that are blinking are items that can be adjusted 4 Adjust each item Press the FM or AM button 5 Repeat step 3 and 4 operation and adjust the date 6 Exit Date adjustment mode Press the MENU button Date Mode Setting the date format 1 Select Date Mode Press the FM or AM button Select the Date Mode display 2 Select the date format Press the ka a or gt gt button Synchronize Clock Synchronizing the RDS station time data and this unit s clock Display Setting SYNC ON Synchronizes the time SYNC OFF Adjust the time manually It takes 3 to 4 minutes to synchronize the clock DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potential thieves Dimmer Dimming this unit s display automatically when the vehicle light switch is turned ON Display Setting Display Setting DSI ON LED flashes Dimmer ON The display dims DSI OFF LED OFF Dimmer OFF The display doesn t dim Selectable Illumination Selecting the button illumination color as green or red Display Setting Button Red The illumination color is red Button Green The illumination color is green Triangle indicator setting Sets the blinking mode during triangle indicator system adjustment such as audio control audio
20. on slide Store unused batteries out of the reach of children Contact a doctor immediately if the battery is accidentally swallowed A Do not set the remote on hot places such as above the dashboard ae lt gt CJ DC DC race a Fey ao pee DE DIRECT OK moo DNPP a Basic operations VOL buttons Adjusting the volume SRC button Each time the button is pressed the source switches For the source switching order refer to Selecting the Source page 13 ATT button Turning the volume down quickly When it is pressed again it returns to the previous level English 55 Basic Operations of remote In Tuner source FM AM buttons Select the band Each time the FM button is pressed it switches between the FM1 FM2 and FM3 bands lt gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations DIRECT OK button Enters and cancels the Direct Access Tuning page 33 mode gt 11 button Enters and cancels the PTY Program Type page 36 mode DNPP button Enters and cancels the SNPP Station Name Preset Play page 34 mode In Disc source lt gt gt buttons Doing track file forward and backward DISC DISC buttons Doing disc folder forward and backward gt 11 button Each time the button is pressed the song pauses and plays DNPP
21. player manual The name of a CD can be changed by the same operation you used to name it Text Title Scroll Scrolling the displayed CD text or MD title Press the SCRL button Function of disc changers with remote DNPP Disc Name Preset Play Selecting the CD displayed in the DNPS of the CDs set in the Disc changer 1 Enter DNPP mode Press the DNPP button on the remote When DNPP is displayed the DNPS display in order Forward Reverse display Press the DISC or DISC button 2 When the disc you want is displayed Press the OK button on the remote The disc being displayed is played Canceling the DNPP mode Press the DNPP button on the remote GSM Hands Free Unit control features NEXT TTT x NAMES msw DIsc F ee SCRL AM Name Telephone number HANGS CE KENWOOD SRCH DIAL CALLE SMSI RTN Receiving a call Received calls can be answered when a GSM Hands Free Unit optional accessory is connected to this unit 1 When a Call is Received Hands Free will be displayed 2 Accept a call Press the 1 3 6 or NEXT button Display A Switching between the Name and Telephone Number Press the TI button Each time the button is pressed the display switches as shown below Information Name Telephone Number 3 Hang up Press the 2 HANG button A Inserting a disc while a call is in
22. progress will cause the telephone to be hung up English 43 GSM Hands Free Unit control features Phone Book Search Selecting a telephone number from the phone book 1 Select the key function section Press the NEXT button Repeatedly press the button until H F is displayed above the 2 KDC W8027 3 KDC PSW9527 W9027 button Refer to Notes on Multi function Key System page 10 2 Enter Hands Free mode Press the 2 3 H F button 3 Select the Phone Book Search Mode item Press the 2 SRCH button Each time the button is pressed the mode switches as follows Phone Book Search Mode item Display Initial Select Mode Initial SEL Redial Mode Redial 4 Select the initial of a person to dial In Initial Select Mode Press the FM or AM button Initials including no corresponding name will not be displayed 5 Switch the Name Press the kaa or gt gt button Switching between the Name and Telephone Number Press the TI button Not available if the name has not been stored Not applicable if the text scroll function has been set to Auto in menu Scrolling the Name and Telephone Number Press the SCRL button 6 Dial a selected number Press the 4 CALL button 7 Hang up Press the 2 HANG button Canceling the Hands Free mode Press the 6 RTN button 44 English Function of remote Direct Dial Inputting the telephone number
23. second The clock display blinks 3 Adjust the hours Press the FM or AM button Adjust the minutes Press the ka a or gt gt button 4 Exit Clock adjustment mode Press the MENU button English 47 Menu system When hands free unit connecting In Standby mode Phone voice speaker setting Selecting the speaker to output the Phone voice Display Setting SP SEL ALL Phone voice sent to the front and rear speaker SP SEL F Right Phone voice send to the front right speaker SP SEL F Left Phone voice sent to the front left speaker When hands free unit connecting Microphone sensitivity adjust Adjusting the volume of the Microphone Display and Setting HE MIC ADJ 00 HF MIC ADJ 15 Original setting HE MIC ADJ 31 When hands free unit connecting Auto Response time Adjust Setting the time from an incoming call to the automatic response Display and Setting Wait Time OFF Wait Time 1s Wait Time 5s Original setting Wait Time 30s If the time set in the GSM telephone is shorter than that set in the unit the former will be used 48 English Date Adjustment 1 Select Date Adjust mode Press the FM or AM button Select the Date Adjust display 2 Enter Date Adjust mode Press the ka or gt gt button for at least 1 second The date display blinks 3 Selecting the item day
24. the original setting Also the explanation for items that aren t applicable 1 Enter Menu mode Manual Clock Adjustment etc are entered step by Press the MENU button for at least 1 second step MENU is displayed 2 Select the menu item Press the FM or AM button Example When you want to set the beep sound select the Beep display In Standby mode 3 Set the menu item Press the ka a or gt gt button Security Code Example When Beep is selected each time the Because authorization by the Security Code is button is pressed it switches Beep ON required when it s removed from the vehicle or Beep OFF Select 1 of them as the personalizing this unit is by using the Security setting Code is a help in preventing theft You can continue by returning to step 2 and setting other items 46 English When the Security Code function is activated it can t be released Note your Security Code is the 4 digit number entered in your Car Audio Passport in this package 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Menu mode Press the MENU button for at least 1 second When MENU is displayed Security is displayed 3 Enter Security Code mode Press the ka a or gt gt button for at least 1 second When ENTER is displayed CODE is displayed 4 Select the digits to enter Press the ka a or gt gt button 5 Select the Security Code numbers Press th
25. with number buttons on the remote and dialing 1 Select the key function section Press the NEXT button Repeatedly press the button until H F is displayed above the 2 3 button Refer to Notes on Multi function Key System page 10 2 Enter Hands Free mode Press the 2 3 H F button 3 Select the Dial Mode Press the 3 DIAL button Number Dial is displayed 4 Enter the telephone number Press the number and ANG buttons on the remote You can input max 32 digits If an incorrect digit is entered pressing the ka a button will clear it 5 Dial an input number Press the 4 CALL button 6 Hang up Press the 2 HANG button Canceling the Hands Free mode Press the 6 RTN button SMS Short Message Service Mode 1 Select the key function section Press the NEXT button Repeatedly press the button until H F is displayed above the 2 3 button Refer to Notes on Multi function Key System page 10 2 Enter Hands Free mode Press the 2 3 H F button 3 Select the SMS Mode Press the 5 SMS button SMS Mode is displayed 4 Select the Message Press the FM or AM button 5 Switch the Display Press the ka a or gt gt button Each time the button is pressed the mode switches as follows SMS Mode item ame Phone Number Date Message When the display line of a message is Text Scroll page 52 set to
26. 18dB Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit For amplifiers there are the model that can be set from Flat to 18 dB and the model that can be set from Flat to 12 dB When an amplifier that can only be set to 12 is connected to the unit AMP Bass 18 won t work correctly even if it s selected B M S Frequency Offset Setting the central frequency boosted by B M S Refer to Audio Setup Easy page 28 and Audio Setup PRO page 30 Audio Setup Easy CABIN SP SEL SP LEV CALL Audio Setup PRO X over DTA EQ SP LEV MEMORY CALL 50 English Display Setting AMP FRQ Normal Boost with the normal central frequency AMP FRQ Low Drop the normal central frequency 20 In Tuner mode News Bulletin with Timeout Setting It switches automatically when a news bulletin starts even if the radio isn t being listened to Also the time interval when interrupt is prohibited can be set Tuning mode Display Operation Auto seek Seek mode Auto 1 Automatic search for a Station Preset station Seek mode Auto 2 Search in order of the stations seek in the Preset memory Manual Seek mode Manual Normal manual tuning control Display and Setting News OFF News 00min News 90min When News 00min News 90min is set the News Bulletin Interrupt
27. Control mode Press the 6 RTN button The setting of this function is available while Display A is selected for the Display mode Upper text display part cannot display the same information as Lower text display part The Album name cannot be displayed during WMA play The text display in the Upper text display In Auxiliary input source part Information Display In Tuner source Auxiliary input name AUX NAME Information Display 7 UN Program Service name or Frequency BAND ch PS SECHE S ANALECLOCK Radio text or Frequency R TEXT ab Date DATE Clock CLOCK ae Spectrum Analyzer amp Clock 5 ANA ECLOCK If the Disc title Track title Song title amp Artist name or Album name amp Artist name is selected when the disc which does not have Disc title Track title Song title Album name or Artist name is played track number and play time are displayed Displaying the frequency during Program Service name reception Press the SCRL button for at least 1 second The frequency for the RDS station will be displayed for 5 seconds instead of the Program Service name In CD amp External disc source Information Display Disc title DISC TITLE Track title TRACK TITLE Track number amp Play time P Time Disc name DNPS Date DATE Clock CLOCK Spectrum Analyzer
28. EQ DTA Audio Setup PRO mode page 30 System Q System Q KDC PSW9527 W9027 page 21 WOW X OVER Audio Control KDC W8027 page 22 The Dual Zone System can be used only when you have set the rear speaker to any mode other than None in the Audio Setup Easy mode page 28 Subwoofer Output Turning the Subwoofer output ON or OFF Press the SW button for at least 1 second Each time the button is pressed Subwoofer output switches ON or OFF When it s ON SUB WOOFER ON is displayed English 25 Function of the KDC PSW9527 KDC W9027 Sound management features NEXT SRC sr amenu SCRL MNAVES BSW DISC 5P LEVEL Front L a z ee i Haa gt gt men TT Tum A ool FRONT MM Ree ee SR Audio control 1 Select the source for adjustment Press the SRC button 2 Select the key function section Press the NEXT button Repeatedly press the button until AD CTRL is displayed above the 2 button Refer to Notes on Multi function Key System page 10 3 Enter Audio Control mode Press the 2 AD CTRL button 4 Select the Adjustment item section Press the NEXT button Repeatedly press the button until the desired Adjustment item is displayed above the 2 5 button 5 Select the Audio Control item for adjustment Press the 2 5 button 26 English Each time the
29. Hiding the Control Panel Prevents tampering with the unit while your car is being serviced etc 12 English Selecting the Source Press the SRC button Source required Display Tuner TUNER CD Compact Disc External disc Optional accessory CD Changer Auxiliary input AUX Standby Illumination only mode STANDBY This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicles battery The time until full power OFF can be set in Power OFF Timer page 52 Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise Attenuator Turning the volume down quickly Press the ATT button Each time the button is pressed the Attenuator turns ON or OFF When it s ON ATT is displayed Rotary Volume knob operation mode select The rotary volume knob can be used for volume adjustment and various function setups Available setup functions The rotary volume knob can be used for the following setup Menu system Item selection Audio Control Adjustment of setup value Audio Setup Adjustment of setup value Display control Display switching Disc Naming Character selection Folder select Folder search You can select the Rotary Volume Operation mode only when the Ea indicator is displayed above the 1 button during any function setup When t
30. KENWOOD KDC PSW9527 KDC W9027 KDC W8027 CD RECEIVER INSTRUCTION MANUAL KENWOOD CORPORATION SRS Riou B64 2746 00 00 EV CHO1 Contents Safety precautions 4 Tuner features 33 Tuning Notes 6 Direct Access Tuning Station Preset Memory About CDs 7 Auto Memory Entry Preset Tuning Notes on playing MP3 WMA 8 SNPP Station Name Preset Play Notes on Multi function Key RDS features 35 System 10 Traffic Information Radio Text Scroll Pate on Sound Management PTY Program Type ystem 11 Program Type preset Generalfeatures 12 Changing Language for PTY Function Power Hiding the Control Panel Selecting the Source Volume Attenuator Rotary Volume knob operation mode select Display Mode Switching Text Display Switching Side Graphic Display Switching Graphic part Spectrum Analyzer Display Switching Wallpaper selecting Text Display Switching External Display Switching Auxiliary Input Display Setting Panel Position Setting Theft Deterrent Panel TEL Mute System Q KDC W8027 System Q KDC PSW9527 KDC W9027 Audio Control KDC W8027 Speaker Setting KDC W8027 Dual Zone System Subwoofer Output Sound management features KDC PSW9527 KDC W9027 26 Audio control Audio Setup Easy mode Audio Setup PRO mode Audio Setup Memory PRO mode Audio Setup memory Recall 2 English CD MP3 WMA External disc control features 38 Playing CD amp
31. LOCK Date DATE If Dual Zone System page 24 is turned ON while the spectrum analyzer is displayed the spectrum analyzer disappears from the display 16 English If the Disc title Track title Song title amp Artist name or Album name amp Artist name is selected when the disc which does not have Disc title Track title Song title Album name or Artist name is played Kenwood Logo are displayed Display A Side Graphic Display Switching Switching the Side graphic Display 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 4 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 4 DISP button 3 Select the display mode Press the 2 MODE button Select the Display A display 4 Enter display control mode Press the 4 SIDE button Side Graphic is displayed 5 Select the side graphic display Press the ka a or gt gt button Each time the button is pressed the side graphic display switches as shown below Side graphic display Text Source Graphic 1 Graphic 3 Spectrum analyzer 1 Spectrum analyzer 4 Blank 6 Exit display control mode Press the 6 RTN button The setting of this function is available while Display A is selected for the Display mode Display B Display C Display D Gra
32. Level 2 Joliet or Romeo The methods and precautions to be followed for writing MP3 WMA data are covered in Notes on playing MP3 WMA page 8 Check that section before creating your MP3 WMA media Playing External Disc Playing discs set in the optional accessory disc player connected to this unit Press the SRC button Select the display for the disc player you want Display examples Display Disc player Compact Disc CD player CD Changer CD changer MD Changer MD changer Pause and play Press the gt I button Each time the button is pressed it pauses and plays The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected Fast Forwarding and Reversing Fast Forwarding Hold down on the gt gt button Release your finger to play the disc at that point Reversing Hold down on the ka a button Release your finger to play the disc at that point Track File Search Searching for a song on the disc or in the MP3 WMA folder Press the ka a or gt gt button Function of disc changer MP3 WMA Disc Search Folder Search Selecting the disc set in the Disc changer or the folder recorded on the MP3 WMA media Press the DISC or DISC button Function of remote Direct Track File Search Doing Track File Search by entering the track file number 1 Enter the track file nu
33. MP3 WMA Playing External Disc Fast Forwarding and Reversing Track File Search Disc Search Folder Search Direct Track File Search Direct Disc Search Track File Disc Folder Repeat Scan Play Random Play agazine Random Play Folder Select Disc Naming DNPS Text Title Scroll DNPP Disc Name Preset Play GSM Hands Free Unit control features 43 Receiving a call Phone Book Search Direct Dial SMS Short Message Service Mode Phone Book Message SMS data synchronize Panel action setting System Q Setting KDC W8027 Audio Setup KDC PSW9527 KDC W9027 Built in Amp Mute Setting B M S Bass Management System B M S Frequency Offset ews Bulletin with Timeout Setting Local See Tuning Mode Auto Memory Entry AF Alternative Frequency Restricting RDS Region Region Restrict Function Auto TP Seek onaural Reception Text Scroll Power OFF Timer Built in Auxiliary input Setting CD Read Setting Picture downloading KDC PSW9527 AMP Control Rotary volume operation select Menu system 46 Basic Operations of remote 55 enu System Loading and Replacing the battery Security Code Basic operations Touch Sensor Tone In Tuner source anual Clock Adjustment In Disc source Phone voice speaker setting GSM Hands Free Unit operations icrophone sensitivity adjust f Auto Response time Adjust Accessories Date Adjustment Installation Procedure 57 Date Mode A 2 Synchroni
34. N and SP SEL parameters using the Audio Setup Easy mode page 28 Refer to Notes on Sound Management System page 11 Function of the KDC PSW9527 When the Dual Zone System page 24 is ON each of the following setup is ignored X over EQ DTA 4 Exit Audio setup mode Press the 6 RTN button Audio Setup Memory PRO mode 1 Selects the PRO mode of Audio setup See the Audio Setup page 50 and select Audio Setup PRO 2 Select the source for adjustment Press the SRC button 3 Select the key function section Press the NEXT button Repeatedly press the button until AD SET is displayed above the 3 button Refer to Notes on Multi function Key System page 10 4 Enter Audio Setup mode Press the 3 AD SET button 5 Select the Adjustment item section Press the NEXT button Repeatedly press the button until the desired Adjustment item is displayed above the 2 5 button 6 Select the Audio Setup item for adjustment Press the 2 5 button Adjust the audio setup by referring to the Audio Setup PRO mode page 30 7 Select the Memory item section Press the NEXT button Repeatedly press the button until MEMORY is displayed above the 2 button 8 Select the Memory item Press the 2 MEMORY button 9 Stores the adjusted audio setup value in memory Press the 2 USER 3 INST button for at least 2 seconds The
35. Press the FM or AM button 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select the Auto Memory Entry mode Press the FM or AM button Select the Auto Memory display 4 Open Auto Memory Entry Press the ka a or gt gt button for at least 2 seconds When 6 stations that can be received are put in the memory Auto Memory Entry closes When the AF Alternative Frequency page 51 is ON only RDS stations are put in the memory When Auto Memory Entry is done in the FM2 band the RDS stations preset in the FM1 band aren t put in the memory Likewise when it is done in the FM3 band RDS stations preset in FM1 or FM2 aren t put in the memory 34 English Preset Tuning Calling up the stations in the memory 1 Select the band Press the FM or AM button 2 Select the key function section Press the NEXT button Repeatedly press the button until 1 6 are displayed above the 1 6 buttons Refer to Notes on Multi function Key System page 10 3 Call up the station Press the desired 1 6 button Function of Remote SNPP Station Name Preset Play Displaying the program service name and selecting the station 1 Enter SNPP mode Press the DNPP button on the remote When SNPP is displayed the program service name displays in the FM1 FM2 FM3 and AM band in order For stations without a program service name the
36. RS and C symbol are trademarks of SRS Labs Inc WOW technology is incorporated under license from SRS Labs Inc 6 English The marking of products using lasers Except for some areas CLASS 1 LASER PRODUCT The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class There is no danger of hazardous radiation outside the unit This Product is not installed by the manufacturer of a vehicle on the production line nor by the professional importer of a vehicle into an EU Member State Dolby Pro Logic Il The matrix decoding technologies that have been evolved from the conventional Dolby Pro Logic system and that is based on the latest digital matrix echnologies It realizes the excellent 5 1 channel sound playback of Dolby Surround and ordinary CD stereo sounds You can enjoy surround channels as ull band sounds from 20 Hz to 20 kHz and stereo sources as real 5 1 channel sounds The Movie mode Music mode Matrix mode can be selected according to the playback source When the Dolby Pro Logic Il mode is selected the sound level is slightly dropped due to its characteristics Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories About CDs Handling CDs Don t touch the recor
37. Speaker Level Set the volume at each setup position 2nd section Multi function key operation Audio setup item 2 2 USER User Memory MEMORY 3 INST User Insttaller B 2 USER Call User CALL 3 INST all Insttaller You can store an adjusted audio setup value by selecting MEMORY Also you can recall it by selecting CALL Refer to Audio Setup memory Recall page 32 3 Adjust the Audio setup item Press the ka a or gt gt button Each time the button is pressed the setting switches as shown below Adjustment Item Range High Pass Filter Front Through 30 250 Hz High Pass Filter Rear High Pass Filter Center Low Pass Filter Subwoofer 30 250 Hz Subwoofer Phase setting Normal Reverse DTA Front DTA Rear 0 610 cm DTA Subwoofer DTA Center 0 170 cm Bass Center Frequency 60 400 Hz Middle Center Frequency 500 Hz 3 15 KHz reble Center Frequency 4 00 kHz 16 00 KHz Bass Level Middle Level 9 9 dB reble Level Bass Q Factor Middle Q Factor 0 25 0 50 1 00 2 00 reble Q Factor SP LEV Front Left SP LEV Front Right 10 10 SP LEV Rear Left SP LEV Rear Right SP LEV Center SP LEV Subwoofer The Adjustment item can also be controlled by the rotary volume knob Refer to Rotary Volume knob operation mode select page 13 To get the best sound first set the CABI
38. Subwoofer Output page 25 is set to SUB WOOFER ON Note that you can control it only when SP LEV is set to any item other than None by Audio Setup Easy mode page28 6 Adjust the Audio Control item Press the ka a or gt gt button Each time the button is pressed the setting switches as shown below 1st section Audio Control Item Range Dolby ProLogic II setting USIC MOVIE MATRIX SRS WOW setting LOW MIDDLE HIGH USER OFF setting Through Bypass Panorama setting ON OFF Dimension control R3 R1 Neutral F1 F3 Center width control 0 7 FOCUS setting 0FF 1 9 SRS TruBass Front setting OFF 1 4 SRS TruBass Rear setting SRS 3D setting OFF 1 4 2nd section Audio Control Item Range Position setting ALL Front L Front R Front Balance setting L15 R15 Fader setting 15 F15 Volume offset 8 0 Subwoofer level 10 10 Subwoofer Phase setting ormal Reverse Function of the KDC PSW9527 The Adjustment item can also be controlled by the rotary volume knob Refer to Rotary Volume knob operation mode select page 13 When the Dual Zone System page 24 is ON each of the following setup is ignored WOW PLII POSI PHASE WOW TruBass FOCUS and SRS 3D are all set to values shown below WOW FOCUS TruBass SRS3D HIGH 8 4 4 MIDDLE 6 3 2 LOW 3 2 1 FOCUS Adjust
39. T Album name amp Artist name ALBUM ARTIST Folder name FOLDER NAME File name FILE NAME Play time amp File number P Time Date DATE Clock CLOCK In Auxiliary input source Information Display Auxiliary input name AUX NAME Date DATE Clock CLOCK In Standby Information Display Standby Illumination only mode STANDBY Date DATE Clock CLOCK Information Display Program Service name or Frequency _ BAND ch PS Radio text R TEXT Date DATE Clock CLOCK Displaying the frequency during Program Service name reception Press the SCRL button for at least 1 second The frequency for the RDS station will be displayed for 5 seconds instead of the Program Service name In CD amp External disc source Information Display Disc title DISC TITLE In External disc source Track title TRACK TITLE Track number amp Play time P Time Disc name DNPS Date DATE Clock CLOCK 18 English 5 Exit Display Control mode Press the 6 RTN button If the Disc title Track title Song title amp Artist name or Album name amp Artist name is selected when the disc which does not have Disc title Track title Song title Album name or Artist name is played track number and play time are displayed External Display Switching Switching the display in the External Display connected 1 Select the key function s
40. XIT button English 41 CD MP3 WMA External disc control features Disc Naming DNPS Attaching a title to a CD 1 Play the disc you want to attach a name to A title can t be attached to MD or MP3 WMA media Refer to the Text Display Switching page14 18 and select the DNPS display 2 Enter name set mode Press the NAME S button for at least 2 seconds NAME SET is displayed 3 Move the cursor to the enter character position Press the ka a or gt gt button 4 Select the character type Press the 2 4 button Each time the button is pressed the character type switches as shown below Character type Button Alphabet Upper case Lower case 2 A a Numbers and symbols 3 1 Special characters Accent characters 4 CHAR 5 Select the characters Press the FM or AM button Characters can be entered by using a remote with a number button Example If DANCE is entered Character Button Times pressed D 3 1 A 2 1 N 6 2 C 2 3 E 3 2 6 Repeat steps 3 through 5 and enter the name 7 Exit name set mode Press the NAME S button 42 English When operation stops for 10 seconds the name at that time is registered and Name Set mode closes Media that you can attach names to Internal CD player 30 discs External CD changer player Varies according to the CD changer player Refer to the CD changer
41. a station 1 Enter PTY mode Press the PTY button This function can t be used during a traffic bulletin or AM reception 2 Select the Program Type Press the FM or AM button Each time the button is pressed the Program Type switches as shown below No Program Type Display 1 Speech All Speech 2 Music All Music 3 News News 4 Current Affairs Current Affairs 5 Information Information 6 Sport Sport 7 Education Education 8 Drama Drama 9 Culture Cultures 0 Science Science 1 Varied Varied Speech 2 Pop Music Pop Music 3 Rock Music Rock Music 4 Easy Listening Music Easy Listening M 5 Light Classical Light Classic M 6 Serious Classical Serious Classics 7 Other Music Other Music 8 Weather Weather amp Metr 9 Finance Finance 20 Children s programs Children s Prog 21 Social Affairs Social Affairs 22 Religion Religion 23 Phone In Phone In 24 ravel Travel amp Touring 25 Leisure Leisure amp Hobby 26 azz Music Jazz Music 27 Country Music Country Music 28 ational Music National Music 29 Oldies Music Oldies Music 30 Folk Music Folk Music 31 Documentary Documentary 36 English Speech and Music include the Program type shown below Music No 12 17 26 30 Speech No 3 11 18 25 31 The Program T
42. amp Clock S ANA CLOCK In MP3 WMA source Information Display Song title amp Artist name TITLE ARTIST Album name amp Artist name ALBUM ARTIST Folder name FOLDER NAME File name FILE NAME Play time amp File number P Time Date DATE Clock CLOCK Spectrum Analyzer amp Clock S ANA CLOCK In Standby Information Display Standby Illumination only mode STANDBY Date DATE Clock CLOCK English 15 General features The text display in the Lower text display part In Tuner source Information Display KENWOOD Logo LOGO Clock CLOCK Spectrum Analyzer amp Clock S ANA CLOCK Radio text R TEXT Date DATE In CD amp External disc source Information Display KENWOOD Logo LOGO Clock CLOCK Spectrum Analyzer amp Clock S ANA CLOCK Disc title DISC TITLE Track Title TRACK TITLE Disc name DNPS Date DATE In MP3 WMA source Information Display KENWOOD Logo LOGO Clock CLOCK Spectrum Analyzer amp Clock S ANA CLOCK Song title amp Artist name TITLE ARTIST Album name amp Artist name ALBUM ARTIST Folder name FOLDER NAME File name FILE NAME Date DATE In Standby Information Display KENWOOD Logo LOGO Clock CLOCK Date DATE In Auxiliary input source Information Display KENWOOD Logo LOGO Clock CLOCK Spectrum Analyzer amp Clock S ANA C
43. and select Audio Setup PRO 2 Select the Audio Setup item for adjustment Select an audio setup item you wish to adjust by referring to Step 2 5 of Audio Setup Easy mode page 28 1st section Function of the KDC W9027 Multi function key operation Audio setup Item 2 2 FRONT High Pass Filter Front X Over 3 REAR High Pass Filter Rear 4 SW Low Pass Filter Subwoofer 4 PHASE Subwoofer Phase setting B 2 FRONT DTA Fron DTA 3 REAR DTA Rear 4 SW DTA Subwoofer 4 2 FRONT 2 BASS EQ Front Bass setting EQ 3 MID EQ Front Middle setting 4 TRE EQ Front Treble setting 3 REAR 2 BASS EQ Rear Bass setting 3 MID EQ Rear Middle setting 4 TRE EQ Rear Treble setting 5 2 FRONT 2 Front L SP LEV Front Left SP 2 Front R SP LEV Front Right LEV B REAR 3 Rear L SP LEV Rear Left 3 Rear R SP LEV Rear Right 4 SW SP LEV Subwoofer i 5 T TONE SP LEV Test tone 30 English Function of the KDC PSW9527 Multi function key operation Audio setup Item 2 2 FRONT High Pass Filter Front X Over 3 REAR High Pass Filter Rear 4 CNTR High Pass Filter Center 5 SW Low Pass Filter Subwoofer 5 PHASE Subwoofer Phase setting B 2 FRONT DTA Fron DTA 3 REAR DTA Rear 4 CNTR DTA Center 5 SW DTA Subwoofer 4 2 FRONT
44. ay continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center Unsupported File A MP3 WMA is played with a format that this unit can t support yes Protected File copy protected file is played A ess Can t Download Download Error This unit does not work properly for some reason Press the reset button to download it again If this error is still displayed consult a local Kenwood dealer No Display File Incorrect File Writing Error DEMO MODE No file that can be downloaded is contained in the CD ROM gt Make sure that a files created with referring to lt http www kenwood net disp com gt is contained in the CD ROM Do not delete the extension kbm created when the file was created The file selected to be downloaded has a format that this unit cannot read Recreate the file Writing failed while the file was downloaded gt Try the downloading again The Demonstration mode has been selected Hold down button 5 and press the Reset button to release the Demonstration mode English 65 Specifications Specifications subject to change without notice FM tuner section Frequency range 50 kHz space 87 5 MHz 108 0 MHz Usable sensitivity S N 26dB 0 7 uV 75 Q Quieting Sensitivity S N 46dB 1 6 UV 75 Q Frequency response 3 0 dB 30 Hz 15 kHz Signal to Noi
45. button is pressed the setting switches as shown below Speaker type Button Display OFF 2 OFF For 5 amp 4 in speaker B 5 4 For 6x9 amp 6 in speaker 4 6 9 6 For the OEM speaker 5 OEM 4 Exit Speaker Setting mode Press the Q button In External disc or Auxiliary input source Dual Zone System Makes the sound different for the front channel and rear channel Output the Internal source sound from either one of the front or rear channels and the sound of other source from the Dual zone channel 1 Select the source Press the SRC button Select the source sound to be output from the Dual zone channel 2 Select the key function section Press the NEXT button Repeatedly press the button until 2 ZN is displayed above the 5 2 button Refer to Notes on Multi function Key System page 10 3 Enter the Dual Zone System Control mode Press the 5 2 ZN KDC W8027 2 2 ZN KDC PSW9527 W9027 button 24 English 4 Select the item for adjustment Press the desired 2 3 button Each time the button is pressed the items that can be adjusted switch as shown below Adjustment Item Button Display Range Dual Zone System 2 ON OFF ON OFF Dual Zone System 3 Fe R Front Rear Front amp Rear Dual Zone System Rear The front is this unit s internal source and the rear is selected source sound Dual Zone System Front The rear is this unit
46. d for this special connection system consult your Kenwood dealer Only use antenna conversion adapters ISO JASO when the antenna cord has an ISO plug Make sure that all wire connections are securely made by inserting jacks until they lock completely If your vehicle s ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a battery wire the power will not be linked with the ignition ie it will not turn on and off along with the ignition If you want to link the units power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition key If the fuse blows first make sure that the wires have not caused a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent short circuits also do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may receive damage or fail to work if you share the wires and or ground them to any metal part in the car After the unit is installed check whether the brake lamps indicators wipers etc on the car are working properly lf the console has a lid make sure to install the unit so that the faceplate does not hit the lid when closing and open
47. ding surface of the CD CD R and CD RW are easier to damage than a normal music CD Use a CD R or a CD RW after reading the caution items on the package etc Don t stick tape etc on the CD Also don t use a CD with tape stuck on it When using a new CD If the CD center hole or outside rim has burrs use it after removing them with a ball pen etc wh J CD accessories Don t use disc type accessories CD cleaning Clean from the center of the disc and move outward Sse Removing CDs When removing CDs from this unit pull them out horizontally CDs that can t be used CDs that aren t round can t be used CDs with coloring on the recording surface or that are dirty can t be used It may not correctly play discs which do not have the mark A CD R or CD RW that hasn t been finalized can t be played For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual CD storage Don t place them in direct sunlight On the seat or dashboard etc and where the temperature is high Store CDs in their cases English 7 Notes on playing MP3 WMA Note however that the MP3 WMA recording media and formats acceptable are limited When writing MP3 WMA pay attention to the following restrictions Acceptable media The MP3 WMA recording media acceptable to this unit are CD ROM CD R and CD RW When using CD RW do full
48. e FM or AM button 6 Repeat steps 4 and 5 and complete the Security Code 7 Confirm the Security Code Press the gt gt button for at least 3 seconds When RE ENTER is displayed CODE is displayed 8 Do the step 4 through 7 step operation and reenter the security code APPROVED is displayed The Security Code function activates If you enter a Code different from your Security Code you have to start over from step 4 Press the Reset button and when it s removed from the battery power source 1 Turn the power ON 2 Do the step 4 through 7 step operation and reenter the security code APPROVED is displayed The unit can be used Ifan incorrect code is input WAITING is displayed and the input prohibited time shown below is generated After the input prohibited time lapses CODE is displayed and input can be done Number of times the Input prohibited time incorrect code was input 1 2 5 minutes 3 1 hour 4 24 hours Touch Sensor Tone Setting the operation check sound beep sound ON OFF Display Setting Beep ON Beep is heard Beep OFF Beep canceled Manual Clock Adjustment This adjustment can be done when the Synchronize Clock page 48 is set as OFF 1 Select Clock Adjustment mode Press the FM or AM button Select the Clock Adjust display 2 Enter Clock Adjust mode Press the ka a or gt gt button for at least 1
49. e MP3 8 320 kbps WMA 48 192 kbps Sampling frequency MP3 8 11 025 12 16 22 05 24 32 44 1 48 kHz WMA 32 44 1 48 kHz When you use your CD writer to record MP3 WMA up to the maximum disc capacity disable additional writing For recording on an empty disc up to the maximum capacity at once check Disc at Once Play mode may not be possible when portions of the functions of Windows Media Player 9 or higher are used Entering ID3 tag The Displayable ID3 tag is ID3 version 1 x For the character code refer to the List of Codes 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 oj jP P l lA D ld 1 1 1 A JQ a q il l AIN ala 2 2 8 Rjblr Pl Alo alo 3 3 C S cls SlAlO alo 4 4 D Tla t al Alo al 5 5 E Ulelu lulA O al 6 6 amp l6 FIVi tiv T 6 7 7 G w g w Cl x e 8 8 H xX h x D t E elo 9 Dlalifvlily U l A J Z j12z a ej B KIT kI E O la C MEJA ENEE afa ioli D M J m el ily ily E gt IN 4 nf 94 7 P if F 1 O o m l lil8lil Entering file and folder names The code list characters are the only file names and folder names that can be entered and displayed If you use any other character for entry the file and folder names are not displayed correctly They may neither be displayed correct
50. ection Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 4 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 4 DISP button 3 Select the display Press the 5 OUT button Disp Out Select is displayed Each time the button is pressed the display switches 4 Exit display control mode Press the 6 RTN button Auxiliary Input Display Setting Selecting the display when this device is switched to Auxiliary input source 1 Select Auxiliary input source Press the SRC button Select the AUX display 2 Enter Auxiliary input display setting mode Press the NAME S button for at least 2 seconds The presently selected AUX Name is blinks 3 Select the Auxiliary input display Press the lt lt or gt gt button Each time the button is pressed it switches through the below displays AUX TV VIDEO GAME PORTABLE DVD 4 Exit Auxiliary input display setting mode Press the NAME S button When operation stops for 10 seconds the name at that time is selected and Auxiliary input display setting mode closes The Auxiliary Input Display can be set only when the built in auxiliary input or the auxiliary input of optional KCA S210A is used Panel Position Setting Setting the angle or back forward position of the control panel 1 Select the key function section Pr
51. ed RDS station isn t sending time data ts Receive another RDS station The Dimmer function doesn t work The Dimmer wire isn t connected correctly ts Check the Dimmer wire connection The panel is not hidden even when the power is turned off The protection function for preventing fingers or other things from getting caught in between the panel and this unit has been activated ts Turn off the power again Sound is interrupted when Dual Zone System is set to ON VY When Dual Zone System is set to ON while the Menu system s AF Alternative Frequency page 51 is set to ON the sound quality may be adversely affected if the internal source is set to the tuner ie Disc source AUX EXT is displayed without achieving External disc control mode VY Unsupported disc changer is connected ts Use the disc changer mentioned in the About CD players disc changers connected to this unit page 5 of the section on Safety precautions There are no audio control effects VY FOCUS SRS 3D item on Audio control KDC PSW9527 W9027 page 26 and SRS WOW item on System Q KDC W8027 page 20 have no effect in rear output ie The Control Panel moves although you do not desire VY The Demonstration mode has been selected ts Hold down button 5 and press the Reset button to release the Demonstration mode Some speakers may not sound even if yo
52. egian Portuguese Portuguese Swedish Swedish German German 4 Exit Changing Language mode Press the SCRL button English 37 CD MP3 WMA External disc control features SRC NEXT cm E TTT E y SCRL NAMES asw DISC Track number Brim DOL T 04 KEN SCAN ROM Playing CD amp MP3 WMA When there is no disc inserted 1 Open the panel to insert disc Press the 4 button 2 Insert a disc When the faceplate has been slid open it might interfere with the shift lever or something else If this happens pay attention to safety and move the shift lever or take an appropriate action then operate the unit The sound will be temporarily muted while the faceplate is moving When a disc is inserted Press the SRC button Select the Compact Disc display 38 English ji AM NAMES DISC DISC Track time 214 50D I REP M ROM ih Pause and play Press the gt I button Each time the button is pressed the song pauses or plays Eject the disc 1 Eject the disc Press the 4 button 2 Return the panel to the original position Press the 4 button A 3 in 8cm disc can t be played Using an adapter and inserting them into this unit can cause damage The MP3 WMA media that this unit can play are CD ROM CD R and CD RW The medium formats must be ISO 9660 Level 1
53. ess the NEXT button Repeatedly press the button until PNL is displayed above the 4 5 button 2 Enter Panel Position Setting mode Press the 4 PNL KDC W8027 5 PNL KDC PSW9527 W9027 button 3 Select the item for adjustment Press the desired 2 5 button Each time the button is pressed the items that can be adjusted switch as shown below Adjustment Item Button Display The panel tilts upwards 2 ANG The panel tilts downwards 3 ANG The panel slides backward 4 SLD The panel slides forward 5 SLD 4 Exit Panel Position Setting mode Press the 6 RTN button A The control panel may be interfered with the shift lever or another part depending on the angles of the control panel Set the angle to avoid any interference When a hard rubber frame is mounted Do not use with the panel slid in the forward direction If so the hard rubber frame will interfere with the panel when the angle is adjusted downward No sound is produced while the panel is operating English 19 General features Theft Deterrent Panel The Backpanel of the unit can be detached and taken with you helping to deter theft Removing the Backpanel 1 Turn the ignition OFF or press the SRC button for at least 1 second Turn OFF the power and the control panel becomes horizontal After the set time passes in OFF Wait Time Setting page49 the panel is closed
54. ey System page 10 3 Enter Audio Control mode Press the 2 AUD button 4 Select the Adjustment item section Press the NEXT button Repeatedly press the button until the desired Adjustment item is displayed above the 2 5 button 6 Adjust the Audio Control item Press the ka a or gt gt button Each time the button is pressed the setting switches as shown below The Adjustment item can also be controlled by the rotary volume knob Refer to Rotary Volume knob operation mode select page 13 7 Exit Audio Control mode Press the 6 RTN button The loudness setting can also be adjusted by pressing the 5 button WOW can be set when SRS WOW or User memory is selected at System Q KDC W8027 page 20 The Loudness can not be set when SRS WOW is selected at System Q KDC W8027 page 20 This mode is available only when Subwoofer Output page 25 is ON 1st section Adjustment Item Button Display Bass 2 BASS Middle Bl MID 1st section Treble 4 TRE 2 button Wow 5 Wow Adjustment Item Display Range Sid section Bass Center Frequency BASS F 60 70 80 100 or 150 Hz d Bass level BASS 8 8dB Adjustment Item Button Display Bass Q Factor BASS Q 1 00 1 25 1 50 2 00 Subwoofer 2 Sw Bass Extend BASS Ext ON OFF High Pass Filter 3 HPF Low Pass Filter 4 LPF 3 button es B
55. f the car Even if Loudness is turned ON high pitched tone isn t compensated for Tuner source is selected ts High pitched tone isn t compensated for when in Tuner source The System Q KDC W8027 page 20 is set to SRS WOW ts Turn it to the other items 62 English The values of Volume offset are low Turn up the Volume offset referring to the section on Audio Control KDC W8027 page 22 Audio control KDC PSW9527 W9027 page 26 The Built in Amp Mute Setting page 50 is ON cs Turn it OFF If the PLII is selected by Audio Setup Easy mode KDC PSW9527 W9027 page28 and if the Front speaker is set to 16 7 10 and the Center speaker is set to 16 over the subwoofer does not sound iw The sound quality is poor or distorted One of the speaker wires is being pinched by a screw in the car Check the speaker wiring The speakers are not wired correctly ts Reconnect the speaker wires so that each output terminal is connected to a different speaker Subwoofer Output Subwoofer Low Pass Filter and Subwoofer setting can t be done The Dual Zone System page 24 is ON ts Turn it OFF The Touch Sensor Tone doesn t sound The preout jack is being used ts The Touch Sensor Tone can t be output from he preout jack Even though Synchronize Clock is ON the clock can t be adjusted The receiv
56. fer 4 2 FRONT 2 Front L Speaker level Front Left SP LEV 2 Front R Speaker level Front Right 3 REAR 3 Rear L Speaker level Rear Left 3 Rear R Speaker level Rear Right 4 SW Speaker level Subwoofer 5 T TONE Speaker level Test tone 5 2 USER Call User CALL 3 INST Call Insttaller 28 English Wagon2 MiniVan1 MiniVan2 SUV Passenger Van Speaker select Front O E M 10 13 16 17 18 cm 4 6 547 6 8 649 7 10 inch Speaker select Rear jone 0 E M 10 13 16 17 18 cm 4 6 571 648 6 9 7 10 inch Speaker select Center one 40 70 mm 5 10 13 16 Over cm Speaker select Subwoofer 16 20 25 30 38 Over cm None Speaker level Front Left 10 10 Speaker level Front Right Speaker level Rear Left Speaker level Rear Right Speaker level Center 10 10 Speaker level Subwoofer The Adjustment item can also be controlled by the rotary volume knob Refer to Rotary Volume knob operation mode select page 13 You can select the Speaker level only when you have set the speaker to anything other than None using the SP SEL Function of the KDC PSW9527 7 Exit Audio setup mode Press the 6 RTN button English 29 Function of the KDC PSW9527 KDC W9027 Sound management features Audio Setup PRO mode 1 Selects the PRO mode of Audio setup See the Audio Setup page 50
57. function is ON When it s ON the News indicator is ON When the news bulletin starts News is displayed and it switches to the news bulletin If you choose the 20min setting further news bulletins will not be received for 20 minutes once the irst news bulletin is received The news bulletin volume is the same level that was set for Traffic Information page 35 This function is only available if the desired station sends PTY code for news bulletin or belongs to Enhanced Other Network Network sending PTY code or news bulletin When the News Bulletin Interrupt function is ON it switches to an FM station In Tuner mode Local Seek Only stations whose reception is good are searched for in auto seek tuning Display Setting Local Seek OFF The local seek function is OFF Local Seek ON The local seek function is ON In Tuner mode Tuning Mode Sets the tuning mode In Tuner mode Auto Memory Entry For the operation method refer to Auto Memory Entry page 34 AF Alternative Frequency When poor reception is experienced automatically switch to another frequency broadcasting the same program in the same RDS network with better reception Display Setting AF ON The AF function is ON AF OFF The AF function is OFF When no other stations with stronger reception are available for the same program in the RDS network you may hear the i
58. he ET indicator is ON you cannot use the rotary volume control for function setup and sound level adjustment To use the rotary volume knob 1 Turn the rotary volume operation ON See the Rotary volume operation select 54 page and select Rotary SEL ON 2 Selecting the Rotary Volume Operation mode Press the 1 button When it s ON the GA indicator blinks 3 Setting the function Rotate the Rotary Volume knob 4 Terminates the function setup using the rotary volume knob Press the 1 button English 13 General features Display Mode Switching Switching the display mode 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 KDC W8027 4 KDC PSW9527 W9027 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 DISP KDC W8027 4 DISP KDC PSW9527 W9027 button 3 Select the display mode Press the 2 MODE button Each time the button is pressed the display mode switches as shown below Display Mode Display Display A Display B Display C Display D Side graphic part Upper text display part Lower text display part Function item display Text display part Graphic amp spectrum analyzer dis
59. he wallpaper Display the wallpapers one after another and select one 1 Turn the wallpaper scan ON Press the BH button Each time the button is pressed the Wallpaper scan is turned ON and OFF When it s ON SCAN is displayed When it s ON each wallpaper is displayed every several seconds 2 At the wallpaper you want to display Press the gt I button Select wallpaper manually Turn the wallpaper scan OFF Press the gt button Each time the button is pressed the Wallpaper scan is turned ON and OFF Select the wallpaper Press the FM or AM button Each time the button is pressed the wallpaper changes ey N 3 Exit Display Control mode Press the 6 RTN button English 17 General features Display B Display C Text Display Switching Switching the text display 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 4 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 4 DISP button 3 Select the display mode Press the 2 MODE button Select the Display B Display C display 4 Select the text Press the 3 TEXT button Itcan also be switched by pressing either lt 4 or gt gt button In Tuner source In MP3 WMA source Information Display Song title amp Artist name TITLE ARTIS
60. ing Mount the unit so that the mounting angle is 30 or less English 57 Connecting Wires to Terminals A Subwoofer output Navy Blue Center output Navy Blue KDC PSW9527 KDC W9027 Subwoofer output Black KDC W8027 Subwoofer left output White Subwoofer right output Red Antenna Conversion Adaptor ISO JASO Accessory att al LL 7 Antenna Cord ISO FM AM antenna input K To External Display Steering remote Fuse 10A N Wiring harness H Accessory External amplifier control wire Pink Black TEL mute wire Brown SD f no connections are made do not let the wire come out from the tab Power control Motor antenna control wire Blue White Battery wire Yellow Ignition wire Red G See next page V4 4 A 7 Pin Red A 4 Pin Yellow Connector A Connector B 58 English i A ey ao B DE Front right output Red Front left output White Rear right output Red Rear left output White AUX right input Red AUX left input White nxn To KENWOOD disc changer GSM hands free unit External optional accessory To connect these leads refer o the relevant instruction manuals
61. is urned ON OFF ADCTRL Law DISP C PNL Function ry ry displaying 5 ye SCAN EDIE REP FSEL 7 ry Notes on Sound Management System The KDC PSW9527 W9027 allows you to set up the best sound field to your car using the audio setup This is the Sound Management System There are two types of audio setup mode Easy audio setup called Easy mode and Professional audio setup called PRO mode Audio setup Easy mode When you select the cabin size and the speaker type you are using in the easy audio setup Easy mode you can set the best sound field to your car automatically Refer to Audio Setup Easy mode page 28 Audio setup PRO mode While in the professional audio setup PRO mode you can fine tune and memory the X Over Cross over DTA Digital Time Alignment and EQ Equalizer controls in addition to the sound quality you have set in the audio setup Easy mode Refer to Audio Setup PRO mode page 30 First set up the sound field in your car by Audio setup Easy mode page 28 Proceed to the following steps for sound field setup 1 Enter Audio Setup mode Press the NEXT button Repeatedly press the button until AD SET is displayed above the 3 button Refer to Notes on Multi function Key System page 10 2 Set the cabin size of your car Press the 2 CABIN button
62. l ou Adjustment Item Display Range 3rd section Middle Center Frequency MIDDLE F 0 5 1 0 1 5 2 0 kHz Middle level MIDDLE L 8 8 dB Adjustment Item Button Display Middle Q Factor MIDDLE Q 1 0 2 0 Balance amp Fader 2 BL F Volume offset 3 VOFF 4 button 7 Adjustment Item Display Range 5 eae Pon tral terior Treble Center Frequency TREBLEF 10 0 12 5 15 0 17 5 kHz Treble level TREBLE L 8 8 dB Press the 2 5 button rene eve Each time the 2 5 button is pressed the 5 button adjustable audio items are switched among ranges of all stage section s tables on the following pages 22 English Adjustment Item Display Range SRS WOW SRS WOW OFF LOW HIGH FOCUS FOCUS OFF LOW HIGH TruBass TruBass ON OFF SRS 3D SRS 3D ON OFF According to the Bass Q Factor setting value the frequencies that can be set in Bass Center Frequency change as shown below Bass Q Factor Bass Center Frequency 1 00 1 25 1 50 60 70 80 100 2 00 60 70 80 150 When the bass extend is set to ON low frequency response is extended by 20 WOW TruBass FOCUS and SRS 3D are all set to values shown below WOW _TruBass FOCUS SRS3D High ON High 0 Low ON Low 0 OFF OFF OFF OFF TruBass Assisting the playback for the super bass sound FOCUS Adjusts the sound image by changing the vertical position of the speakers virtually and increases or decreases the s
63. ly depending on the CD writer used The unit recognizes and plays only those MP3 WMA which have the MP3 WMA extension MP3 WMA A file with a name entered with characters not on the code list may not play correctly Writing files into a medium When a medium containing MP3 WMA data is loaded the unit checks all the data on the medium If the medium contains a lot of folders or non MP3 WMA files therefore it takes a long time until the unit starts playing MP3 WMA In addition it may take time for the unit to move to the next MP3 WMA file or a File Search or Folder Search may not be performed smoothly A Loading such a medium may produce loud noise to damage the speakers Do no attempt to play a medium containing a non MP3 WMA file with the MP3 WMA extension The unit mistakes non MP3 WMA files for MP3 WMA data as long as they have the MP3 WMA extension Do not attempt to play a medium containing non MP3 WMA MP3 WMA playing order When selected for play Folder Search File Search or for Folder Select files and folders are accessed in the order in which they were written by the CD writer Because of this the order in which they are expected to be played may not match the order in which they are actually played You may be able to set the order in which MP3 WMA are to be played by writing them onto a medium such as a CD R with their file names beginning with play sequence numbers such as 01 to 99 dependi
64. mber Press the number buttons on the remote 2 Do Track File Search Press the ka a or gt gt button Canceling Direct Track File Search Press the gt I button Function of disc changers with remote Direct Disc Search Doing Disc Search by entering the disc number 1 Enter the disc number Press the number buttons on the remote 2 Do Disc Search Press the DISC or DISC button Canceling Direct Disc Search Press the gt I button English 39 CD MP3 WMA External disc control features Track File Disc Folder Repeat Replaying the song disc in the Disc changer or MP3 WMA folder you re listening to 1 Select the key function section Press the NEXT button Repeatedly press the button until REP is displayed above the 4 button Refer to Notes on Multi function Key System page 10 2 Turn ON OFF the Repeat Play Press the 4 REP button Each time the button is pressed the Repeat Play switches as shown below In CD amp External disc source Repeat play Display Track Repeat Repeat ON In Disc Changer Track Repeat ON Disc Repeat In Disc Changer Disc Repeat ON OFF Repeat OFF In MP3 WMA source Repeat play Display File Repeat File Repeat ON Folder Repeat Folder Repeat ON OFF Repeat OFF Scan Play Playing the first part of each song on the disc or MP3 WMA folder you are listening to and searching for the song you want to listen to 1 Selec
65. n AUX OFF When selecting the source there s no Auxiliary Input Display Setting Builtin AUX ON When selecting the source there s Auxiliary MONO OFF The monaural reception is OFF Input MONO ON The monaural reception is ON In Standby mode Text Scroll R CD Read Setting Setting the displayed text scroll Display Setting Scroll Manual Doesn t scroll Scroll Auto Scrolls when the display changes The text scrolled is shown below CD text Folder name File name Song title Artist name Album name MD title Radio text Text for GSM hands free source message etc Power OFF Timer Setting the timer to turn this unit s power OFF automatically when Standby mode continues Using this setting can save the vehicle s battery power 52 English When there is a problem on playing a CD with special format this setting play the CD by force Display Setting CD READ 1 Play CD and MP3 WMA CD READ 2 Play CD by force Setting CD READ 2 cannot play MP3 WMA Some music CDs may not be played back even in the CD READ 2 mode Function of the KDC PSW9527 In Standby mode Picture downloading Downloading movies and wallpapers Downloaded pictures can be used for the display of this unit 1 Inset a CD R CD RW Insert a CD R CD RW containing files to be downloaded into this unit Refer to Playing CD amp MP3 WMA page 38 for details Our URL http www kenwo
66. n ON OFF the Random Play by pressing he 3 button during CD play Setting each function The function display will show the controllable unction of the 2 5 button above the button Pressing the 2 5 button below the desired unction enables the setting of the function Displaying the desired function f five or more functions are available to be set with he 2 5 button they are divided into multiple unction groups referred to as sections in this manual for registration Press the NEXT button to switch the sections f the display of the desired function is not shown press the NEXT button 1 to 3 times to switch the sections until the wanted function display is shown Example Function display of CD amp External disc source 1st section ADCTRL ADSET DISP PNL 2nd section ren NEXT 2 2N 3rd section INEXT SCAN RDM REP FSEL MRDM H F SYNC or DISP are displayed when an optional accessory is connected 10 English Real operational example of the Multi function Key System Example Turning ON OFF the Random Play during CD play 1 Show the function display of the Random Play f RDM is not shown in the display press the NEXT button to switch the sections until the RDM function display is shown above the 3 button 2 Turn ON OFF the Random Play Press the 3 button Each time the 3 button under the RDM unction display is pressed the Random Play
67. ncoming broadcast in bits and snatches Turn OFF the AF function in such a case Restricting RDS Region Region Restrict Function You can choose whether or not to restrict the RDS channels received with the AF function for a particular network to a specific region Display Setting Regional ON The Region Restrict Function is ON Regional OFF The Region Restrict Function is OFF Sometimes stations in the same network broadcast different programs or use different program service names English 51 Menu system Auto TP Seek When the TI function is ON and poor reception conditions are experienced when listening to a traffic information station another traffic information station with better reception will be searched for automatically Display Setting ATPS ON The Auto TP Seek Function is ON ATPS OFF The Auto TP Seek Function is OFF In FM reception Monaural Reception Display Setting OE Power OFF Timer function is OFF OFF 20min urns the power OFF after 20 minutes Original setting OFF 40min urns the power OFF after 40 minutes OFF 60min urns the power OFF after 60 minutes This setting is done after setting Security Code page 46 Built in Auxiliary input Setting Set the Built in Auxiliary Input function Noise can be reduced when stereo broadcasts are Display Setting received as monaural Builti
68. ng on your CD writer For example a medium with the following folder ile hierarchy is subject to Folder Search File Search or Folder Select as shown below Example of a medium s folder file hierarchy CJ on Folder A File 3 Root d0 O A DS do do AO ae dO a DO Lt gt e C JR Level 1 Level 3 Level 5 Level 2 Level 4 When a File Search is executed with file being played Operation of the button Current file DE Haa Button Beginning of file JE gt H DO HO bP Button When a Folder Search is executed with file being played Operation of the button AM Button Current folder FM Button When Folder Select is selected with file S being played to move from folder to folder Operation of the bution Current folder lt 4 Button Ex bp Button ta AM Button ex FM Button English 9 Notes on Multi function Key System Multi function Key System serves to control various functions with the 2 5 buttons The basic operation of the Multi function Key System is described below What s the Multi function Key System This unit is equipped with the Multi function Key System that enables the operation of multiple unctions with one button For example you can enter the Display Control Mode or tur
69. ng the Unit 1 Refer to the section Removing the hard rubber frame page 61 and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown Screw M4X8 commercially available Accessory Removal tool 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it English 61 Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General The power does not turn ON w The fuse has blown te After checking for short circuits in the wires replace the fuse with one with the same rating Speaker cable touches on chassis etc ts Wire or insulate the speaker cable properly and press the reset button The Bass center frequency Bass quality factor Bass extend Middle center frequency Middle quality factor and Treble center frequency can t be adjusted V The System Q Setting page 50 is set OFF we Set it ON No sound can be heard or the volume is low The fader or balance settings are set all the way to one side ss Center the fade
70. od net disp com describes how to make CD R CD RW 2 Enter Standby Press the SRC button Select the STANDBY display 3 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 4 Select the downloading mode Press the FM or AM button Select the DISP Data DL display 5 Enter the downloading mode Press the ka a or gt gt button File Check is displayed 6 Select files to be downloaded Press the FM or AM button 7 Start downloading Press the ka a or gt gt button for at least 2 seconds Downloading is displayed When the downloading finishes Finished Download is displayed Picture download may take as long as 10 minutes Downloading gone z Gradation Level Canceling Downloading Press the MENU button 8 Exit the downloading mode Press the MENU button The number of files that can be downloaded Downloaded movie 1 file Wallpaper 1 file When a new movie is downloaded it is overwritten to the currently downloaded movie Also when a new wallpaper is downloaded it is overwritten to the currently downloaded wallpaper There is no way to delete the downloaded pictures The downloaded pictures can be used for display Graphic part Spectrum Analyzer Display Switching page 17 Wallpaper selecting page 17 When you can t download the pictures to this unit there may be a problem with the CD R CD RW write
71. oundscape SRS 3D Making a natural 3D sound field SRS 3D cannot be set in tuner source 2nd section 2 button Adjustment Item Display Range Subwoofer level SW LEVEL 15 15 Subwoofer phase PHASE Normal 0 Reverse 180 3 button Adjustment Item Display Range Front High Pass Filter X OVER Front Through 40 60 80 100 120 150 180 220 Hz Rear High Pass Filter X OVER Rear Through 40 60 80 100 120 150 180 220 Hz 4 button Adjustment Item Display Range Subwoofer X OVER Sub Woofer 50 80 120 Through Hz Low Pass Filter 5 button Adjustment Item Display Range Loudness LOUD ON OFF Loudness Compensating for low and high tones during low volume 3rd section 2 button Adjustment Item Display Range Balance BL Left 15 Right 15 Fader fe Rear 15 Front 15 3 button Adjustment Item Display Range Volume offset VOL OFFSET 8 0 Volume offset Each source s volume can be set as a difference from the basic volume English 23 General features Function of the KDC W8027 Speaker Setting Fine tuning so that the System Q value is optimal when setting the speaker type 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Speaker Setting mode Press the Q button SP SELECT is displayed 3 Select the Speaker type Press the 2 5 button Each time the
72. phic part Spectrum Analyzer Display Switching Switching the graphic Display Spectrum analyzer display 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 4 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 4 DISP button 3 Select the display mode Press the 2 MODE button Select the Display B Display C Display D display 4 Select the graphic spectrum analyzer display Press the 4 SA grph button 5 Select the graphic spectrum analyzer display part display Press the ka a or gt gt button Each time the button is pressed the graphic display spectrum analyzer display switches as shown below Graphic display Spectrum Analyzer display Movie 1 Movie 2 Downloaded movie Spectrum analyzer 1 Spectrum analyzer 5 Wallpaper Function of the KDC PSW9527 6 Exit display control mode Press the 6 RTN button The setting of this function is available while Display B Display C Display D is selected for the Display mode Display B Display C Display D Wallpaper selecting Select a wallpaper to display when Display Type is set to Display B Display C Display D 1 Select the wallpaper display Refer to Graphic part Spectrum Analyzer Display Switching page 17 2 Select t
73. play part 4 Exit display control mode Press the 6 RTN button No function item is displayed if Display C or Display D is selected To use a function item press any of 1 to 6 buttons or NEXT button The function item will be displayed approximately 5 seconds 14 English When the Dual Zone System page 24 is ON the spectrum analyzer cannot be displayed The display is dimmed during Display B or Display C mode The indicator appears only when the Clock is displayed in the upper or lower position during Display A mode Display A Text Display Switching Switching the text display 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 4 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 4 DISP button 3 Select the display mode Press the 2 MODE button Select the Display A display 4 Enter text select mode Press the 3 TEXT button In the Rotary Volume Operation mode you can select the Upper part or Lower part using button 3 TEXT and switch the display using the rotary volume key 5 Select the text in the upper text display part Press the FM or AM button Select the text in the lower text display part Press the ka a or gt gt button Refer to the table described later for setting items 6 Exit Display
74. r and balance settings WY The input output wires or wiring harness are connected incorrectly t Reconnect the input output wires or the wiring harness correctly See the section on Connecting Wires to Terminals The Demonstration mode has been selected ts Hold down button 5 and press the Reset button to release the Demonstration mode There s a source you can t switch There s no media inserted ts Set the media you want to listen to If there s no media in this unit you can t switch to each source The Disc changer isn t connected ts Connect the Disc changer If the Disc changer isn t connected to it s input terminal You can t switch to an external disc source The memory is erased when the ignition is turned OFF The ignition and battery wire are incorrectly connected Connect the wire correctly referring to the section on Connecting Wires to Terminals There s no loudness effect The System Q KDC W8027 page 20 is set to SRS WOW ts Turn it to the other items The TEL mute function does not work The TEL mute wire is not connected properly Connect the wire correctly referring to the section on Connecting Wires to Terminals The TEL mute function turns ON even though the TEL mute wire is not connected The TEL mute wire is touching a metal part of the car ts Pull the TEL mute wire away from the metal part o
75. s been removed Replace it The unit is malfunctioning for some reason Press the reset button on the unit If the E 77 code does not disappear consult your nearest service center Something is wrong with the disc magazine Or the unit is malfunctioning for some reason gt Check the disc magazine And then press the reset button on the unit If the Mecha Error code does not disappear consult your nearest service center Hold Error The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60 C 140 F stopping all operation Cool down the unit by opening the windows or turning on the air conditioner As the temperature falls below 60 C 140 F the disc will start playing again Attempted to display DNPS during the CD play having no disc names preset Attempted to display SNPS during the receiving session of the station having no station name preset Attempted to display the ID3 tag while the MP3 WMA having no ID3 tag is being played NO NAME Waiting Radio text data is being received Load Discs are being exchanged in the Disc changer Reading The unit is reading the data on the disc NO ACCESS After setting it in the Disc Changer DNPP was done without having it been played at least 1 time IN Blink The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the displ
76. s internal source and the front is selected source sound 5 Exit the Dual Zone System Control mode Press the 6 RTN button 6 Select the source Press the SRC button Select the source sound to be output from the internal source channel The Dual Zone System can be used with the sources shown below Internal auxiliary input KCA S210A CA C1AX External disc changer player While Dual Zone System is ON the setting of Dual Zone System Front or Rear is disabled Set Dual Zone System Front or Rear first and then set the Dual Zone System to ON When the Dual Zone System is ON there is no Dual zone channel audio control or other effect When you use the Dual Zone System by selecting the optional accessory source for the output of the Dual zone channel you cannot select another optional accessory source as the source for the Internal source channel When SRS WOW is selected at System Q KDC W8027 page 20 the Dual Zone System cannot be turned on and off Also set all the Audio Control KDC W8027 page 22 WOW items to OFF The Dual Zone System cannot be turned on and off if even one of the items is set to ON The Dual Zone System cannot be used if a GSM hands free unit or a DAB control unit is connected When the Dual Zone System is ON each of the following setup is ignored WOW PLII POSI PHASE Audio control KDC PSW9527 W9027 page 26 X over
77. s the sound image by changing the vertical position of the speakers virtually and increases or decreases the soundscape TruBass Assisting the playback for the super bass sound SRS 3D Making a natural 3D sound field SRS 3D cannot be set in tuner source The Dimension Control can be set only when the rear speaker is ON The Center Width Control can be set only when the center speaker is ON Before you set the TruBass F TruBass R to get he best sound set the speaker size using the Audio Setup Easy mode page 28 function Refer to Notes on Sound Management System page 11 7 Exit Audio Control mode Press the 6 RTN button English 27 Function of the KDC PSW9527 KDC W9027 Sound management features Audio Setup Easy mode 1 Selects the Easy mode of Audio setup See the Audio Setup page 50 and select Audio Setup Easy 2 Select the source for adjustment Press the SRC button 3 Select the key function section Press the NEXT button Repeatedly press the button until AD SET is displayed above the 3 button Refer to Notes on Multi function Key System page 10 4 Enter Audio Setup mode Press the 3 AD SET button 5 Select the Audio Setup item for adjustment Press the 2 5 button Each time the 2 5 button is pressed the adjustable audio items are switched among ranges of all stage section s tables on the following pages F
78. se ratio MONO 65 dB Selectivity DIN 400 kHz gt 80 dB Stereo separation 1 kHz 35 dB MW tuner section Frequency range 9 kHz space 531 kHz 1611 kHz Usable sensitivity S N 20dB 25 uV LW tuner section Frequency range 153 kHz 281 kHz Usable sensitivity S N 20dB 745 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed CD DA MP3 WMA 1000 400 rpm CLV 2times Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 01 Signal to Noise ratio 1 kHz 105 dB Dynamic range 93 dB Channel separation 95 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio 66 English Audio section Maximum output power 50Wx4 Output power DIN 45324 B 14 4V 30W x4 Tone action KDC W8027 Bass 60 Hz 150 Hz 8 dB iddle 500 Hz 2 kHz 8 dB Treble 10 kHz 17 5 kHz 8 dB KDC PSW9527 W9027 Bass 60 Hz 400 Hz 9 dB iddle 500 Hz 3 15 kHz 9 dB Treble 4 kHz 16 kHz 9 dB Preout level Load during disc play 5000 mV 10 kQ KDC PSW9527 W9027 2000 mV 10 kQ KDC W8027 Preout impedance during disc play lt 80 Q KDC PSW9527 W9027 lt 600 Q KDC W8027 Auxiliary input Frequency response 1 dB 20 Hz 20 kHz Input Maxim
79. setup multi key system setup Display Setting TRIAGL Blink ON The Triangle indicator blinks TRIAGL Blink OFF The Triangle indicator does not blink Font Type Select Selecting the display font 1 Select Font Type Select Mode Press the FM or AM button Select the Font Select display 2 Select the font Press the ka a or gt gt button OFF Wait Time Setting Setting the time until the faceplate hide operation starts after the power is turned OFF The faceplate can be removed only during the set time period Display and Setting Off Wait Osec Off Wait 3sec Original setting Off Wait 25sec In Standby mode Eject angle setting This function sets the opening and closing operation of a panel when a disc is inserted and when it is ejected Display Setting Eject ANG Slope Opens and closes the panel while maintaining the angle of the control panel to the set angle Eject ANG Level Opens and closes the panel after setting the angle of the control panel to the horizontal position English 49 Menu system In Standby mode Panel action setting Sets the panel movement when the panel action back forward movement is set to its most end position Display Setting In Standby mode Built in Amp Mute Setting Toggles ON or OFF the mute control on the built in amplifier Turning ON this control enhances the preout quality
80. t sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not set the removed faceplate or the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing To prevent deterioration do not touch the erminals of the unit or faceplate with your ingers Do not subject the faceplate to excessive shock as it is a piece of precision equipment When replacing a fuse only use a new one with he prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction To prevent a short circuit when replacing a fuse irst disconnect the wiring harness Do not place any object between the faceplate and the unit Do not apply excessive force to the moving faceplate Doing so will cause damage or malfunction Do not apply excessive force to the open faceplate or place objects on it Doing so will cause damage or breakdown Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit About CD players disc changers connected to this unit ENWOOD disc changers CD players released in 1998 or later can be connected to this unit Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers CD players ote that any KENWOOD disc changers CD players released
81. t the key function section Press the NEXT button Repeat to press the button until SCAN is displayed above the 2 button Refer to Notes on Multi function Key System page 10 2 Start Scan Play Press the 2 SCAN button Scan ON is displayed 3 Release it when the song you want to listen to is played Press the 2 button 40 English Random Play Play all the songs on the disc or MP3 WMA folder in random order 1 Select the key function section Press the NEXT button Repeatedly press the button until RDM is displayed above the 3 button Refer to Notes on Multi function Key System page 10 2 Turn ON OFF the Random Play Press the 3 RDM button Each time the button is pressed Random Play urns ON or OFF When it s ON Random ON is displayed When the gt button is pressed the next song select starts Function of disc changer Magazine Random Play Play the songs on all the discs in the disc changer in random order 1 Select the key function section Press the NEXT button Repeatedly press the button until M RDM is displayed above the 5 button Refer to Notes on Multi function Key System page 10 2 Turning ON OFF the Magazine Random Play Press the 5 M RDM button Each time the button is pressed the Magazine Random Play turns ON or OFF When it s ON M Random ON is displayed When the bl button is pressed the next song select starts
82. the ignition and the A 4 pin yellow is connected to the constant power supply Ignition cable Red A 7 Pin Red Unit Vehicle gt Battery cable Yellow A 4 Pin Yellow N The A 7 pin red of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin yellow is linked to the ignition Ignition cable Red A 7 Pin Red Unit Vehicle Battery cable A 4 Pin Yellow Yellow w The A 4 pin yellow of the vehicle s ISO connector is not connected to anything while the A 7 pin red is connected to the constant power supply or both the A 7 red and A 4 yellow pins are connected to the constant power supply Ignition cable Red A 7 Pin Red Unit Vehicle gt Connect to a power source that can be turned on and Battery cable off with the ignition key Yellow English 59 Installation Installation Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw commercially available Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip A To attach this unit make sure the front of the control panel faces you and fit it into the mounting sleeve by
83. u control the T TONE WY You have selected None by Speaker Select control ts The speaker does not sound if it has been set to None by Speaker Select control The specified disc does not play but another one plays instead w The specified CD is quite dirty t Clean the CD V The disc is loaded in a different slot from that specified ts Eject the disc magazine and check the number for the specified disc w The disc is severely scratched ts Try another disc instead A CD ejects as soon as it is loaded VY The CD is quite dirty ts Clean the CD referring to the CD cleaning of the section on About CDs page 7 Can t remove disc The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF ts The disc can only be removed within 10 minutes of the ACC switch being turned OFF If more than 10 minutes has elapsed turn the ACC switch ON again and press the Eject button v ts The subwoofer does not sound Tuner source Radio reception is poor The car antenna is not extended ts Pull the antenna out all the way WY The antenna control wire is not connected ts Connect the wire correctly referring to the section on Connecting Wires to Terminals The desired frequency can t be entered with the Direct Access Tuning Y A station that can t be received is being entered ts Enter a station that can be received
84. um Voltage 1200 mV Input Impedance 100 kQ General Operating voltage 11 16V allowable 144V Current consumption 10A Installation Size W x H x D 182 x 53 x 163 m m KDC PSW9527 W9027 182 x 53 x 162 mm KDC W8027 Weight 2 1 kg KDC PSW9527 W9027 1 9 kg KDC W8027 KENWOOD
85. unction of the KDC W9027 Multi function key operation Audio setup item Function of the KDC PSW9527 Multi function key operation Audio setup item 2 Cabin setting CABIN 3 2 FRONT Speaker select Front SP SEL 3 REAR Speaker select Rear 4 CNTR Speaker select Center 5 Sw Speaker select Subwoofer 4 2 FRONT 2 Front L Speaker level Front Left SP LEV 2 Front R Speaker level Front Right 3 REAR 3 Rear L Speaker level Rear Left 3 Rear R Speaker level Rear Right 4 CT SW 4 Center Speaker level Center 4 SubWoofer Speaker level Subwoofer 5 T TONE Speaker level Test tone 5 2 USER all User CALL 3 INST Call Insttaller You can recall the value you h Audio setup to Audio Setup memory Reca ave adjusted in the RO mode by selecting the CALL Refer Il page 32 You can listen to the T TONE when you have tuned it The sound level is reduced when T TONE is selected The sound returns to the normal level when the original source is s elected 6 Adjust the Audio setup item Press the ka a or gt gt button Each time the button is pressed the setting switches as shown below Audio setup Item Range Cabin setting OFF Compact Sedan Wagon1 2 Cabin setting CABIN B 2 FRONT Speaker select Front SP SEL 3 REAR Speaker select Rear 4 SW Speaker select Subwoo
86. witches between the FM1 FM2 and FM3 bands 3 Tune up or down band Press the ka a or gt gt button Frequency display 8 1 4 KENWOOD 72 UNS a IH Function of remote Direct Access Tuning Entering the frequency and tuning 1 Select the band Press the FM or AM button 2 Enter Direct Access Tuning mode Press the DIRECT button on the remote is displayed 3 Enter the frequency Press the number buttons on the remote Example Desired frequency Press button 92 1 MHz FM 0 9 2 1 810 kHz AM 0 8 1 0 Canceling Direct Access Tuning Press the DIRECT button on the remote English 33 Tuner features Station Preset Memory Putting the station in the memory 1 Select the band Press the FM or AM button 2 Select the frequency to put in the memory Press the ka a or gt gt button 3 Select the key function section Press the NEXT button Repeatedly press the button until 1 6 are displayed above the 1 6 buttons Refer to Notes on Multi function Key System page 10 4 Put the frequency in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button Auto Memory Entry Putting a station with good reception in the memory automatically 1 Select the band for Auto Memory Entry
87. y The values set on the Audio Control KDC W8027 page 22 Each setting value is changed with the Speaker Setting page 24 First select the speaker type with the Speaker setting When Dual Zone System page 24 is set to ON the setting of SRS WOW is disabled Function of the KDC PSW9527 KDC W9027 System Q You can recall the best sound setting preset for different types of music 1 Select the source to set Press the SRC button 2 Select the Sound type Press the Q button Each time the button is pressed the sound setting switches Sound setting Display atural Natural Rock ROCK Pops POPS Easy EASY op 40 TOP 40 azz JAZZ User memory USER nstaller INSTALLER User memory The values set on the Audio Setup PRO mode page 30 Installer The values set on the Audio Setup PRO mode page 30 Each setting value is changed with the Audio Setup PRO mode page 30 First select the Cabin size and the speaker type with Audio Setup Easy mode page 28 Refer to Notes on Sound Management System page 11 English 21 General features Function of the KDC W8027 Audio Control 1 Select the source for adjustment Press the SRC button 2 Select the key function section Press the NEXT button Repeatedly press the button until AUD is displayed above the 2 button Refer to Notes on Multi function K
88. ype can be put in the 1 6 button memory and called up quickly Refer to the Program Type preset page 36 The display language can be changed Refer to Changing Language for PTY Function page 37 3 Search for the selected Program Type station Press the kaa or gt gt button When you want to search for other stations press the kaa or gt gt button again When the selected Program Type isn t found NO PTY is displayed Select another Program Type 4 Exit PTY mode Press the PTY button Program Type preset Putting the Program Type in the Preset button memory and calling it up quickly Presetting the Program Type 1 Select the Program Type to preset Refer to PTY Program Type page 36 2 Preset the Program Type Press the desired 1 6 button for at least 2 seconds Calling up the preset Program Type 1 Enter PTY mode Refer to PTY Program Type page 36 2 Call up the Program Type Press the desired 1 6 button Changing Language for PTY Function Selecting the Program Type display language 1 Enter PTY mode Refer to PTY Program Type page 36 2 Enter Changing Language mode Press the SCRL button 3 Select the language Press the FM or AM button Each time the button is pressed the language switches as shown below Language Display English English Spanish Spanish French French Dutch Dutch Norwegian Norw
89. ze Clock Connecting Wires to Terminals 58 DSI Disabled System Indicator s Selectable Illumination Installation 60 Triangle indicator setting x Font Type Select Removing the Unit 61 Dimmer x r OFF Wait Time Setting Troubleshooting Guide 62 Eject tti og P R Specifications 66 English 3 Safety precautions AWARNING To prevent injury or fire take the following precautions Insert the unit all the way in until it is fully locked in place Otherwise it may fall out of place when jolted When extending the ignition battery or ground wires make sure to use automotive grade wires or other wires with a 0 75mm AWG18 or more to prevent wire deterioration and damage to the wire coating To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit If the unit starts to emit smoke or strange smells turn off the power immediately and consult your Kenwood dealer Make sure not to get your fingers caught between he faceplate and the unit Be careful not to drop the unit or subject it to rong shock The unit may break or crack because it contains glass parts wa 4 English ACAUTION To prevent damage to the machine take the following precautions Make sure to ground the unit to a negative 12V DC power supply Do not open the top or bottom covers of the unit Do not install the unit in a spot exposed to direc

Kenwood KDC-PSW9527 Car Stereo System User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents