Home

Kenwood KDC-PS9070R Car Stereo System User Manual

1. A Ge T RDS indicator Tl indicator Traffic Information Changing to traffic information automatically when a traffic bulletin starts even when you are not listening to the radio Press the TI button Each time you press the button the Traffic information function turns ON and OFF When traffic information is ON Tl indicator is ON When a traffic information station is not being received the Tl indicator blinks When a traffic bulletin starts TRAFFIC is displayed and the audio changes to traffic information During reception of an AM station when the Traffic Information function is turned ON the frequency changes to an FM station During reception of traffic information the adjusted volume is automatically remembered and the next time the audio changes to traffic information the volume automatically becomes the remembered volume PTY indicator Receiving other traffic information stations Push the Control knob towards ka a or gt gt Traffic information can be switched when it is on the Tuner Source However you cannot switch the Traffic information during reception of the Traffic bulletin switched from the source other than the Tuner Radio Text Scroll Scrolling the displayed radio text Push the Control knob toward FM for at least 2 seconds When the lt Display Illumination Control gt page 29 is set to
2. For amplifiers there are the models you can set from Flat to 18 dB and the models you can set from Flat to 12 cB When an amplifier that can only be set to 12 is connected to the unit BMS 18 will not work correctly even if it is selected Function of the KDC W6534U Other than Standby mode B M S Frequency Offset Setting the central frequency boosted by B M S Display Setting BMSF NML Boost with the normal central frequency BMSF LOW Drop the normal central frequency 20 Function of the KDC W6534U When LX AMP unit connecting AMP Control You can control the LX AMP connected to the unit 1 Select AMP Control mode Push the Control knob towards FM or AM Select the AMP CTRL display 2 Enter AMP Control mode Press the Control knob for at least 1 second 3 Select the AMP Control item for adjustment Push the Control knob towards FM or AM For the details on the AMP Control item see the Instruction manual attached to the LX AMP 4 Adjust the AMP Control item Push the Control knob towards ka a or gt gt 5 Exit AMP Control mode Press the MENU button You cannot use the LX AMP operation during standby mode News Bulletin with Timeout Setting The tuner automatically changes when a news bulletin starts even if the radio is not being Ifyou choose the 20MIN setting further news bulletins will not be received for 20 minutes once the first news bulletin
3. Attenuator Selecting the source Ejecting the disc Turning off the power During function control such as the Menu System the display stays on English 29 Menu system In Standby mode Dimmer Dimming this unit s display automatically when the vehicle light switch is turned ON Display Setting DIM ON The display dims DIM OFF The display doesn t dim Function of the KDC W6534U In Standby mode Switching preout Alternating the preout between the rear and subwoofer With the subwoofer the sound outputs without being effected by fader control Display Setting SWPRE R Rear preout SWPRE SW Subwoofer preout Function of the KDC W6534U In Standby mode Built in Amp Setting Controlling the built in amplifier Turning OFF this control enhances the preout quality Display Setting AMP ON The built in amplifier activates AMP OFF The built in amplifier deactivates 30 English Function of the KDC W6534U Other than Standby mode B M S Bass Management System Adjust the bass boost level of the external amplifier using the main unit Display Setting BMS FLT Bass boost level is flat BMS 6 Bass boost level is low 6dB BMS 12 Bass boost level is mid 12dB BMS 18 Bass boost level is high 18dB Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit
4. The maximum number of characters for display CD R RW File Folder name 128 characters MP3 ID3 Tag WMA Contents property 30 characters AAC song information 60 characters File Folder name is the number of the characters including the extensions This unit can display the following versions of MP3 ID3 tag version 1 0 1 1 2 2 2 3 AAC ID3 Tag cannot be displayed Limitation of structure for the file and the folder CD R RW Maximum number of directory levels 8 Maximum number of folders 100 Maximum number of files per folder 4096 About partition of the USB device While using the USB device virtual folders are created to control the partition in the USB device These folders appear in the first level root directory as is an alphabet to identify each partition Even when the USB device does not have partition A folder is created and audio files are controlled inside this folder Playing order of the Audio file The Audio file plays in the order which is written by CD writing software You may be able to set the playing order by writing the play sequence numbers such as 01 to 99 at the beginning of the file name Audio files are played in the order the files are written You can specify the order of playback by numbering files in a folder and writing them by folder USB device Example o cD CD Cc Folder L ya 2 Audio file A os 1 0 a Lode i DO
5. ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center The speaker wire has a short circuit or touches the chassis of the vehicle and then the protection function is activated gt Wire or insulate the speaker cable properly and press the reset button An Audio file is played with a format that this unit can t support D gt A copy protected file is played mr The Demonstration mode has been selected The lt Demonstration mode Setting gt page 35 is ON Turn it OFF The USB device is selected as a source although no USB device is connected gt Change the source to any source other than USB Connect an USB device and change the source to USB again An unsupported USB device is connected gt For the supported USB devices refer to lt About USB device gt page 7 Media was played that doesn t have data recorded that the unit can play The connected USB device contains no playable audio file Use media that has data recorded that the unit can play The connected USB device is rated a current capacity higher than the allowable limit gt Check the USB device with reference to lt About USB device gt page 7 Some trouble may have occurred to the connected USB device Remove the USB device and then reconnect it When the same message displays again use another USB devi
6. the audio pauses or plays Removing the USB device 1 Select a source other than the USB device Press the SRC button 2 Remove the USB device A Removing the USB device with it selected as a source can damage the data stored in the USB device You can remove the USB device safely with the unit power turned off Function of the KDC W6534U KDC W5534U Playing External Disc Playing discs set in the optional accessory disc player connected to this unit Press the SRC button Select the display for the disc player you want Display examples Display Disc player CD CH CD changer MD CH MD changer Pause and play Press the Control knob Each time you press the knob the audio pauses or plays Disc 10 is displayed as 0 The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected English 21 CD USB device Audio file External disc control features Fast Forwarding and Reversing Fast Forwarding Hold down toward gt gt with the Control knob Release to resume the playback Reversing Hold down toward ka with the Control knob Release to resume the playback There is no sound while the Audio file is being searched You cannot fast Forwarding and Reversing depending on AAC file format Track File Search Searching for a song on the disc or in the Audio file folder Push the C
7. 7 the vehicle Battery wire Yellow Ignition wire Red See next page A 7 Pin Red 1a A 4 Pin Yellow Connector A Connector B English 37 Connecting Wires to Terminals KDC W5534U W534U ED Do not remove the cap when you do not use the USB cable The connector will cause the unit to malfunction if TA To USB device it gets in touch with any metallic part of the vehicle USB connector Steering remote control __ rags Steering remote control Light Blue Yellow maa Front right output Red KDC W5534U only Front left output White KDC W5534U only L Rear left output White Rear right output Red FM AM antenna input E lt O Antenna Cord ISO Antenna Conversion Adaptor ISO JASO Accessory H Fuse 10A To Kenwood disc changer External optional accessory KDC W5534U only Wiring harness Accessory ED To connect these leads refer to the relevant instruction manuals Connect to the terminal that is grounded when either the telephone rings or during conversation To connect the Kenwood navigation system consult your navigation manual TEL mute wire Brown I i If no connections are made do not let the wire come out from the tab Power control Motor antenna control wire Connect either to the power Blue White control terminal when using
8. KDC W6534U External Display Control Changing the display of the External Display connected to this unit Display OEM DISP Each time you push the knob towards ka a or gt gt the display switches Function of the KDC W6534U KDC W5534U Auxiliary Input Display Setting Selecting the display when alternating to Auxiliary input source 1 Select Auxiliary input source Press the SRC button Select the AUX AUX EXT display 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Auxiliary input display setting mode Push the Control knob towards FM or AM Select the NAME SET display 4 Enter Auxiliary input display setting mode Press the Control knob for at least 1 second The selected Auxiliary input display is displayed 5 Select the Auxiliary input display Push the Control knob towards a a or gt gt Each time you push the knob the display alternates as listed below AUX AUX EXT DVD PORTABLE GAME VIDEO TV 6 Exit Auxiliary input display setting mode Press the MENU button When operation stops for 10 seconds the name at that time is registered and the Auxiliary input display setting mode closes You can only set the Auxiliary input display when the auxiliary input of optional KCA S210A is used KDC W5534U Text Scroll Setting the displayed text scroll Display Sett
9. Memory Putting a station in the memory 1 Select the band Push the Control knob towards FM or AM 2 Select the frequency to put in the memory Push the Control knob towards ka a or gt 3 Put the frequency in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button English 15 Tuner features Auto Memory Entry Putting stations with good reception in the memory automatically 1 Select the band for Auto Memory Entry Push the Control knob towards FM or AM 2 Open Auto Memory Entry Press the AME button for at least 2 seconds A MEMORY is displayed When 6 stations that can be received are put in the memory Auto Memory Entry closes When the lt AF Alternative Frequency gt page 32 is ON only RDS stations are put in the memory When Auto Memory Entry is done in the FM2 band the RDS stations preset in the FM1 band are not put in the memory Likewise when Auto Memory Entry is done in the FM3 band RDS stations preset in FM1 or FM2 are not put in the memory Preset Tuning Recalling the stations in the memory 1 Select the band Push the Control knob towards FM or AM 2 Recall the station Press the desired 1 6 button 16 English RDS features KENWOOD
10. OFF the display may black out while scrolling English 17 RDS features PTY Program Type Selecting the Program Type and searching for a station 1 Enter PTY mode Press the Control knob During PTY mode the PTY indicator is ON This function cannot be used during a traffic bulletin or AM reception 2 Select the Program Type Push the Control knob towards FM or AM Each time you push the knob the Program Type alternates between program types shown in the able below No Program Type Display Speech SPEECH 2 Music MUSIC 3 News NEWS 4 Current Affairs AFFAIRS 3 Information INFO 6 Sport SPORT T Education EDUCATE 8 Drama DRAMA 9 Culture CULTURE 0 Science SCIENCE 1 Varied VARIED 2 Pop Music POP M 3 Rock Music ROCK M 4 Easy Listening Music EASY M 5 Light Classical LIGHT M 6 Serious Classical CLASSICS 7 Other Music OTHER M 8 Weather WEATHER 9 Finance FINANCE 20 Children s programs CHILDREN 21 Social Affairs SOCIAL 22 Religion RELIGION 23 hone In PHONE IN 24 ravel TRAVEL 25 Leisure LEISURE 26 azz Music JAZZ 27 Country Music COUNTRY 28 ational Music NATION M 29 Oldies Music OLDIES 30 Folk Music FOLK M 31 Documentary DOCUMENT 18 English Sp
11. Push the Control knob toward FM for at least 2 seconds When the lt Display Illumination Control gt page 29 is set to OFF the display may black out while scrolling Menu system MENU Menu display NEWS indicator RDS indicator Menu System Setting beep sound during operation etc functions The Menu system basic operation method is explained here The reference for the Menu items and their setting content is after this operation explanation 1 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 2 Select the menu item Push the Control knob towards FM or AM Example When you want to set the beep sound select the BEEP display 3 Set the menu item Push the Control knob towards ka a or gt gt Example When you select BEEP each time you push the knob it alternates between BEEP ON or BEEP OFF Select 1 of them as the setting You can continue by returning to step 2 and setting other items 4 Exit Menu mode Press the MENU button When other items those applicable to the basic operation method above are displayed their setting content chart is entered Normally the setting listed at the top of the chart is the original setting Also the explanation for items that are not applicable lt Manual Cloc
12. The specified disc does not play but another one plays instead y The specified CD is quite dirty t Clean the CD W The disc is loaded in a different slot from that specified te Eject the disc magazine and check the number for the specified disc W The disc is severely scratched ts Try another disc instead Can t remove disc v The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF ts The disc can only be removed within 10 minutes of the ACC switch being turned OFF If more than 10 minutes has elapsed turn the ACC switch ON again and press the Eject button The disc won t insert W There s already another disc inserted t Press the 4 button and remove the disc Direct Search can t be done Y Another function is ON ts Turn Random Play or other functions OFF Track Search can t be done WV For the discs folders first or last song ts For each disc folder Track Search can t be done in the backward direction for the first song or in the forward direction for the last song Audio file source Cannot play an Audio file WY The media is scratched or dirty te Clean the media referring to the CD cleaning of the section on lt About CDs gt page 6 The sound skips when an Audio file is being played WY The media is scratched or dirty ts Clean the media referring to the CD cleaning of the section on lt About CDs gt pag
13. _ do Playing order Playing order after play AO DO HO DO File search Forward file search during amp play Push the Control knob towards bb J e Folder search Forward folder search during play Push the Control knob towards FM 3 File select hen the selection is set to file HO Push the Control knob towards gt i 0 0 e Folder select 1 hen the selection is set to directory 4 and you want to skip to the folder 2 at the same level Push the Control knob towards lt lt 2 hen the selection is set to directory 2 moves the level up by folder select Push the Control knob towards AM 2 e Folder select 2 hen the selection is set to directory CJ and you want to skip to the folder 4 Push the Control knob towards bb GJ a English 9 General features EM escrt wate KENWOOD Control knob Release button Clock display Power Turning ON the Power Press the SRC button LOUD indicator ATT indicator When the power is ON the lt Security Code gt page 28 is displayed as CODE ON or CODE OFF Turning OFF the Power Press the SRC button for at least 1 second Selecting the Source Press the SRC button Function of the KDC W6534U Function of the KDC W
14. dust or the possibility of water splashing Do not place the faceplate and the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing To prevent deterioration do not touch the erminals of the unit or faceplate with your ingers Do not subject the faceplate to excessive shock as it is a piece of precision equipment When replacing a fuse only use a new fuse with he prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction Do not apply excessive force to the open aceplate or place objects on it Doing so will cause damage or breakdown Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit Do Not Load 8 cm 3 in CDs in the CD slot If you try to load a 8 cm 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit About CD players disc changers connected to this unit Kenwood disc changers CD players released in 1998 or later can be connected to this unit Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers CD players ote that any Kenwood disc changers CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit Connecting unsupported disc changers CD players o this unit m
15. is received The news bulletin volume is the same level that was set for lt Traffic Information gt page 17 This news bulletin function is only available if the desired station sends PTY code for news bulletin or belongs to lt Enhanced Other Network gt Network sending PTY code for news bulletin When the News Bulletin Interrupt function is ON the tuner changes to an FM station In Tuner mode Local Seek Only stations whose reception is good are searched in auto seek tuning Display Setting LO S OFF The local seek function is OFF LO S ON The local seek function is ON In Tuner mode Tuning Mode Sets the tuning mode Tuning mode Display Operation listened to Also you can set the time interval Auto seek AUTO 1 Automatic search for a station when interruption is prohibited Preset station seek AUTO 2 Search in order of the stations in the Preset memory Display and Setting Manual MANUAL Normal manual tuning control NEWS OFF NEWS 00M NEWS 90M When you set NEWS 00M NEWS 90M the News Bulletin Interrupt function is ON When the News Bulletin is ON the NEWS indicator is ON When the news bulletin starts NEWS is displayed and the tuner changes to the news bulletin English 31 Menu system AF Alternative Frequency When the reception is poor automatically alternate to another frequency broadcasting the same program in t
16. knob the language alternates between the languages shown in the table below Language Display English ENGLISH French FRENCH Swedish SWEDISH German GERMAN KDC W6534U only 4 Exit Changing Language mode Press the TI button English 19 CD USB device Audio file External disc control features Control knob Release button S MODE SCAN RDM 3 REP F SEL M RDM SRC A RDM Track number Play time FOLDER ALBUM IN indicator Playing CD amp Audio file When there is no disc inserted 1 Drop open the faceplate Press the Release button 2 Insert a disc 3 Push the faceplate on the left side and return it to its former position AN When the faceplate has been dropped open it might interfere with the shift lever or other vehicle function If this happens pay attention to safety and move the shift lever or take an appropriate action to remove the obstacle then operate the unit Do not use the unit with the faceplate in the open condition If it s used in the open position dust can enter the inside part and cause damage When a disc is inserted the IN indicator is ON You can cancel the announcement when selecting the folder by lt Voice Index gt page 34 during the play of the ACDrive media KDC W6534U only 20 English GEN
17. 6534U W5534U This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicle s battery The time until full power OFF can be set in lt Power OFF Timer gt page 33 Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise Source required Display Tuner TUNER USB device USB O CD External disc Optional accessory CD CH Auxiliary input AUX Auxiliary input Optional accessory AUX EXT Standby Illumination only mode STANDBY 10 English Attenuator Turning the volume down quickly Press the ATT button Each time you press the button the Attenuator turns ON and OFF When the Attenuator is ON the ATT indicator blinks System Q Selecting the best sound setting preset for different types of music 1 Select the source to set Press the SRC button 2 Select the Sound type Press the Q button When you press the button once the current sound setting is displayed Each time you press the button the sound setting alternates Sound setting Display User memory USER ock ROCK ops POPS Easy EASY op 40 TOP 40 azz JAZZ atural NATURAL User memory The values set on the lt Audio Control gt page 11 KDC W5534U W534U does not have the User memory function so the values of Bass Middle an
18. Album name amp Artist name ALBUM Folder name FOLDER File name FILE Track number amp Play time P TIME Clock CLOCK In Standby Auxiliary input source Information Display Source name SRC NAME Clock CLOCK 3 Exit Switching Display mode Press the Control knob When LX AMP is connected the item setup by the Display mode of LX AMP is displayed KDC W6534U only If the contents of the information cannot be displayed Play time is displayed Track number at Audio file displays the last 3 digits when it exceeds 1000 songs When you select the clock display the display setting of each source will be changed to the clock display English 13 General features Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you helping to deter theft Removing the Faceplate 1 Press the Release button Drop open the faceplate 2 Drawing the faceplate to left side pull it to forward and remove it The faceplate is a precision piece of equipment and can be damaged by shocks or jolts Keep the faceplate in its faceplate case while detached Do not expose the faceplate and the faceplate case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Faceplate 1 Align the shaft on the unit with the depression on the faceplate 2 Push the facep
19. KENWOOD CD RECEIVER KDC W6534U KDC W5534U KDC W534U INSTRUCTION MANUAL Kenwood Corporation Contents Safety precautions Notes About CDs About USB device About AAC MP3 and WMA N Q W General features 1 Power Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Setting Subwoofer Output Switching Display Theft Deterrent Faceplate TEL Mute Tuner features 15 Tuning Station Preset Memory Auto Memory Entry Preset Tuning RDS features 17 Traffic Information Radio Text Scroll PTY Program Type Program Type preset Changing Language for PTY Function CD USB device Audio file External disc control features 20 U aying CD amp Audio file aying USB device aying External Disc Fast Forwarding and Reversing Track File Search Disc Search Folder Search Track File Disc Folder Repeat Scan Play Random Play agazine Random Play All Random Play Select mode File Select mode U U 2 English Folder Select 1 mode Folder Select 2 mode Switching the Play mode Letter Seek Text Title Scroll Menu system 27 enu System Security Code Touch Sensor Tone anual Clock Adjustment Synchronize Clock DSI Disabled System Indicator Selectable Illumination Display Illumination Control Dimmer Switching preout Built in Amp Setting B M S Bass Management System B M S Frequency Offset A
20. MP Control ews Bulletin with Timeout Setting Local Seek Tuning Mode AF Alternative Frequency Restricting RDS Region Region Restrict Function Auto TP Seek onaural Reception External Display Control Auxiliary Input Display Setting Text Scroll Built in Auxiliary input Setting Power OFF Timer CD Read Setting Voice Index Firmware version display Unique ID display Audio Preset Memory Audio Preset Recall Demonstration mode Setting Accessories Installation Procedure 36 Connecting Wires to Terminals 37 Installation 40 Removing the Unit 41 Troubleshooting Guide 42 Specifications 45 Safety precautions AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals Attach the panel while you are on the vehicle The panel lock arm appears when the panel is removed Therefore the panel must be attached while the electrical system of the car is operating ACAUTION To prevent damage to the machine take the following precautions Make sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much
21. RE Play mode Disc number When a disc is inserted Press the SRC button Select the CD display Pause and play Press the Control knob Each time you press the knob the audio pauses or plays Eject the disc 1 Drop open the faceplate Press the Release button 2 Eject the disc Press the 4 button 3 Press the faceplate on the left side and return it to its former position Playing USB device Playing USB device 1 Select a source other than the USB device Press the SRC button 2 Connect the USB device 3 Select USB source Press the SRC button Select the USB display For the types of available USB devices and how to connect USB devices refer to lt About USB device gt page 7 After you stopped playing a file contained in the USB device you can restart playing the file from the point where you stopped its playback Even after removing the USB device you can restart playing the file from the point where you stopped its playback as long as the files contained in the USB device are all the same Be sure to insert the USB device connector as far as it will go You can play the disc ACDrive media made by Media Manager by the same operation KDC W6534U only You can cancel the announcement when selecting the folder by lt Voice Index gt page 34 during the play of the ACDrive media KDC W6534U only Pause and play Press the Control knob Each time you press the knob
22. SEL2 Refer to lt Folder Select 2 mode gt page 25 Exit the Select mode The Select mode does not function when lt All Random Play gt page 23 is ON You cannot operate this function when lt Random Play gt page 23 is set to ON You cannot operate this function when lt Switching the Play mode gt page 25 is set to other than FOLDER while playing ACDrive media 2 Select the file folder Refer to the explanation of the procedure performed in each select mode Scrolling the file folder name display Push the Control knob toward FM for at least 2 seconds You can cancel the announcement when selecting the folder by lt Voice Index gt page 34 during the play of the ACDrive media KDC W6534U only In the File Select mode the lt Voice Index gt page 34 announcement is not made KDC W6534U only English 23 CD USB device Audio file External disc control features Function of Audio file File Select mode You can select an audio file in the folder currently being played by file name 1 Enter File Select mode Press the F SEL button Select the FILE SEL display Refer to lt Select mode gt page 23 File name display Displays the current file name 2 Select the file Push the Control knob towards ka a or gt gt Switching between files in units of 10 songs Push the Control knob towards FM or AM With the FM button you move 10 songs up and with
23. Set the media you want to listen to If there s no media in this unit you can t switch to each source W The Disc changer isn t connected t Connect the Disc changer If the Disc changer isn t connected to it s input terminal you can t switch to an external disc source The memory is erased when the ignition is turned OFF Y The ignition and battery wire are incorrectly connected t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt page 37 38 The TEL mute function does not work YW TheTEL mute wire is not connected properly t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt page 37 38 The TEL mute function turns ON even though the TEL mute wire is not connected Y The TEL mute wire is touching a metal part of the Car ts Pull the TEL mute wire away from the metal part of the car Even if Loudness is turned ON high pitched tone isn t compensated for Y Tuner source is selected te High pitched tone isn t compensated for when in Tuner source 42 English Y The lt Built in Amp Setting gt page 30 is OFF te Turn it ON The sound quality is poor or distorted Y One of the speaker wires is being pinched by a screw in the car t Check the speaker wiring W The speakers are not wired correctly te Reconnect the speaker wires so that each output terminal is connected to a d
24. Y display 6 Put the Audio Preset in the memory Press the Control knob for at least 2 seconds The MEMORY display blinks 1 time 7 Exit Audio Preset mode Press the MENU button Register 1 pair of Audio Preset Memory You cannot register by the source When you press the Reset all the sources will be the setting value which is registered The following items cannot be registered Volume Balance Fader Loudness Volume offset Function of the KDC W6534U Other than Standby mode Audio Preset Recall Recalling the sound setup registered by lt Audio Preset Memory gt page 34 1 Select the source Press the SRC button 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Audio Preset mode Push the Control knob towards FM or AM Select the A PRESET display 4 Enter Audio Preset mode Press the Control knob for at least 1 second 5 Select the Audio Preset Recall Push the Control knob towards FM or AM Select the RECALL display 6 Recall the Audio Preset Press the Control knob for at least 2 seconds The RECALL display blinks 1 time 7 Exit Audio Preset mode Press the MENU button The User memory of lt System Q gt page 11 is changed to the value which was recalled The source tone memory item of lt Audio Control gt page 11 is changed to the value which was recalled by the selected source In Standby mode Demonstratio
25. acters which can be displayed by this unit are A Z 0 9 amp lt gt A The RDS feature won t work where the service is not supported by any broadcasting station The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may be inapplicable How to reset your unit If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed Remove the USB device before pressing the Reset button Pressing the Reset button with the USB device installed can damage the data contained in the USB device For how to remove the USB device refer to lt Playing USB device gt page 21 Press the Reset button if the disc auto changer fails to operate correctly Normal operation should be restored ar O KENWOOD EA ae a eS a fro ore os ee rs oe Reset button 4 English Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe it again with a clean soft dry c
26. and the protection unction may have been activated Therefore the speaker wire should be checked If your car is not prepared for this special connection system consult your Kenwood dealer Only use antenna conversion adapters ISO JASO when he antenna cord has an ISO plug Make sure that all wire connections are securely made by inserting jacks until they lock completely If your vehicle s ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a battery wire the power will not be linked with the ignition i e it will not turn on and off along with the ignition If you want to link the unit s power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition key If the fuse blows first make sure that the wires have not caused a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent short circuits also do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may receive damage or fail to work if you share the wires and or ground them to any metal part in the car After the unit is installed check whether the brake lamps indicators wipers etc on the car are working properly If t
27. ant to listen to is played Press the SCAN button Random Play Play all the songs on the disc or Audio file folder in random order Press the RDM button Each time you press the button Random Play turns ON or OFF When the Random mode is ON DISC RDM FOLD RDM RDM ON is displayed When you push the Control knob toward gt i the next random song starts Function of the KDC W6534U KDC W5534U Function of disc changer Magazine Random Play Play the songs on all the discs in the disc changer in random order Press the M RDM button Each time you press the button the Magazine Random Play turns ON or OFF When the Magazine Random mode is ON MGZN RDM is displayed When you push the Control knob toward gt i the next random song starts Function of Audio file All Random Play Playing randomly from all of the Audio files recorded in the media Press the A RDM button for at least 1 second When the random mode is ON ALL RDM is displayed Cancelling the All Random Play Press the A RDM button When you push the Control knob toward gt i the next random song starts Function of Audio file Select mode Quickly selecting the file or folder you want to hear 1 Select the Select mode Press the F SEL button Display Select mode FILE SEL Refer to lt File Select mode gt page 24 FLD SEL1 FLD SEL Refer to lt Folder Select 1 mode gt page 24 FLD
28. ay result in damage Set the O N Switch to the N position for the applicable Kenwood disc changers CD players The functions you can use and the information hat can be displayed may differ depending on the models being connected A You can damage both your unit and the CD changer if you connect them incorrectly Lens Fogging When you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging this condensation on the lens may not allow CDs to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer The AAC logo is trademark of Dolby Laboratories English 3 Notes No USB device comes with this unit You need to purchase a commercially available USB device For the types of available USB devices refer to lt About USB device gt page 7 If you experience problems during installation consult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they work with your model and in your area If the unit fails to operate properly press the Reset button The unit returns to factory settings when he Reset button is pressed Press the reset button if the disc auto changer fails o operate correctly Normal operation should be restored The char
29. c play 2500 mV 10 kQ KDC W6534U 2000 mV 10 kQ KDC W5534U W534U Preout impedance lt 6000 Cc SB Interface USB Standard USB1 1 2 0 File System FAT16 32 aximum Supply current 500 MA P3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files Auxiliary input KDC W6534U Frequency responce 1 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input impedance 100 kQ General Operating voltage 11 16V allowable 14 4V Current consumption 10A Installation Size W x H x D 182 x 53x 155 mm Weight 1 40 kg English 45 KENWOOD
30. ce Specifications Specifications subject to change without notice FM tuner section Frequency range 50 kHz space 87 5 MHz 108 0 MHz Usable sensitivity S N 26dB 0 7 WV 75 Q Quieting Sensitivity S N 46cB 1 6 pV 75 0 Frequency response 3 0 dB 30 Hz 15 kHz Signal to Noise ratio MONO 65 dB Selectivity DIN 400 kHz gt 80 dB Stereo separation 1 kHz 35 dB MW tuner section Frequency range 9 kHz space 531 kHz 1611 kHz Usable sensitivity S N 20dB 25 uV LW tuner section Frequency range 153 kHz 281 kHz Usable sensitivity S N 20dB 745 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed 1000 400 rpm CLV 2times Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 008 Signal to Noise ratio 1 kHz 110 dB Dynamic range 93 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files Audio section Maximum output power 50 W x 4 KDC W6534U W5534U 45 W x 4 KDC W534U Output power DIN 45324 B 14 4V 30 W x 4 KDC W6534U W5534U 28 W x 4 KDC W534U Speaker impedance 4 8Q Tone action Bass 100 Hz 8 dB Middle 1 kHz 8 dB Treble 10 kHz 8 dB Preout level Load during dis
31. d Treble set in audio control are replaced to the System Q values and USER is not displayed when the System Q setting is changed Change each setting value with the lt Speaker Setting gt page 12 First select the speaker type with the Speaker setting Audio Control 1 Select the source to adjust Press the SRC button 2 Enter Audio Control mode Press the VOL knob 3 Select the Basic Audio item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Adjust the Basic Audio item Turn the VOL knob Adjustment Item _ Display Range Subwoofer level 23 SW L 15 15 Bass level BAS L 8 8 Middle level MID L 8 8 Treble level TRE L 8 8 Balance BAL Left 15 Right 15 Fader FAD Rear 15 Front 15 Exit Audio Control mode Volume control mode Function of the KDC W6534U You can control this item when lt Switching preout gt page 30 is set to SWPRE SW You can control this item when lt Subwoofer Output gt page 12 is set to SW ON 4 Source tone memory Puts the set up value in the memory per source 5 Exit Audio Control mode Press any button Press a button other than the VOL knob and ATT button English 11 General features Audio Setup Setting the Sound system such as Cross over Network 1 S
32. e USB device again referring to www kenwood mediamanager p If the error message is still displayed initialize the USB device or use other USB devices The CD is upside down Load the CD correctly Nothing has been recorded on the MD No tracks are recorded on the MD although it has a title The faceplate of the slave unit being connected to this unit has been removed Replace it The unit is malfunctioning for some reason gt Press the reset button on the unit If the E 77 code does not disappear consult your nearest service center Something is wrong with the disc magazine Or the unit is malfunctioning for some reason gt Check the disc magazine And then press the reset button on the unit If the E 99 code does not disappear consult your nearest service center Discs are being exchanged in the Disc changer The unit is reading the data on the disc 44 English HOLD IN Blink PROTECT NA FILE COPY PRO DEMO MODE NO DVICE NA DVICE NO MUSIC E 15 USB ERR The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60 C 140 F stopping all operation Cool down the unit by opening the windows or turning on the air conditioner As the temperature falls below 60 C 140 F the disc will start playing again The CD player section is not operating properly Reinsert the CD If the CD cannot be
33. e function for this unit may be differed from the Instruction manual therefore refer to the following supplemental instruction lt Auto Ensemble Memory Entry gt 1 Select the preset band for Auto Ensemble Memory Entry 2 Press the AME button for at least 2 seconds Open Auto Ensemble Memory Entry After storing in the memory finishes the number of the pre set buttons and the ensemble label are displayed lt Searching by programme type and language gt and lt Languages to be displayed gt in lt Programme Type PTY Function gt At the operation to press DISP button use T I button instead lt Automatic Switching DAB priority gt This function cannot be used This Product is not installed by the manufacturer of a vehicle on the production line nor by the professional importer of a vehicle into an EU Member State Information on Disposal of Old Electrical and Electronic Equipment applicable for EU countries that have adopted separate waste collection systems Products with the symbol crossed out wheeled bin cannot be disposed as household waste Old electrical and electronic equipment ME should be recycled at a facility capable of handling these items and their waste byproducts Contact your local authority for details in locating a recycle facility nearest to you Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the envir
34. e 6 Y The recording condition is bad te Record the media again or use another media The Audio file track time isn t displayed correctly Gus ts There are times when it isn t displayed correctly according to the Audio file recording conditions USB device source The USB device is not detected Y The USB connector is disconnected ts Connect the connector of the USB device properly The USB device does not play its audio files VY The USB connector is disconnected ts Connect the connector of the USB device properly English 43 Troubleshooting Guide The messages shown below display your systems condition EJECT NO DISC TOC ERR READ ERR E 05 BLANK NO TRACK NO PANEL E 77 E 99 LOAD READING o disc magazine has been loaded in the changer The disc magazine is not completely loaded Load the disc magazine properly jo CD in the unit Insert the CD o disc has been loaded in the disc agazine Load a disc into the disc magazine a3 o disc has been loaded in the disc magazine Load a disc into the disc magazine The CD is quite dirty The CD is upside down The CD is scratched a lot Clean the CD and load it correctly The number of files or folders which are stored in the connected USB device is above the limitation The file system of the connected USB device is broken Copy the files and folders for th
35. ecorder instruction manual CD storage Do not place CDs in direct sunlight On the seat or dashboard etc or where the temperature is high Store CDs in their cases About USB device Notes on Use of the USB device This unit can play audio files stored in the flash memory and digital audio player that have a USB port these devices are referred to as USB devices in this document The following restrictions are placed on the types and usage of available USB devices Available USB devices USB devices belonging to the USB mass storage class USB devices whose maximum current consumption is 500 mA or less For the supported formats and USB device types refer to http www kenwood mediamanager jp USB Mass Storage Class USB devices that the PC can recognize as an external storage without using any special driver or application software Contact the sales agent as to whether your USB device conforms to the USB mass storage class specs Using an unsupported USB device can result in abnormal playback or display of the audio file Even if you use the USB device conforming to the above specs audio files cannot be played normally depending on the type or condition of the USB device About the Connection of the USB device When connecting the USB device usage of the CA U1EX option is recommended Normal playback is not guaranteed when a cable other than the USB compatible cable is used Co
36. eech and Music include the Program type shown below Music No 12 17 26 30 Speech No 3 11 18 25 31 You can put the Program Type in the 1 6 button memory and for quick recall Refer to the lt Program Type preset gt page 18 You can change the display language Refer to lt Changing Language for PTY Function gt page 19 3 Search for the selected Program Type station Push the Control knob towards ka a or gt gt When you want to search for other stations push aa or PI of the Control knob again When the selected Program Type is not found NO PTY is displayed Select another Program Type 4 Exit PTY mode Press the Control knob Program Type preset Putting the Program Type in the Preset button memory and quick recall Presetting the Program Type 1 Select the Program Type to preset Refer to lt PTY Program Type gt page 18 2 Preset the Program Type Press the desired 1 6 button for at least 2 seconds Recalling the preset Program Type 1 Enter PTY mode Refer to lt PTY Program Type gt page 18 2 Recall the Program Type Press the desired 1 6 button Changing Language for PTY Function Selecting the Program Type display language 1 Enter PTY mode Refer to lt PTY Program Type gt page 18 2 Enter Changing Language mode Press the TI button 3 Select the language Push the Control knob towards FM or AM Each time you push the
37. elect the source to adjust Press the SRC button 2 Enter Audio Setup mode Press the VOL knob for at least 1 second 3 Select the Audio Setup item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Setup the Audio item Turn the VOL knob Adjustment Item __ Display Range Front High Pass Filter HPF Through 40 60 80 100 120 150 180 220 Hz Rear High Pass Filter HPR Through 40 60 80 100 120 150 180 220 Hz Low Pass Filter LPF 50 60 80 100 120 Through Hz Subwoofer Phase 23 PHAS Reverse 180 Normal 0 Volume offset V OFF 8 0 Loudness LOUD OFF ON Volume offset Sets each source s volume as a difference from the basic volume Loudness Compensates for low and high tones during low volume Function of the KDC W6534U You can control this item when lt Switching preout gt page 30 is set to SWPRE SW You can control this item when lt Subwoofer Output gt page 12 is set to SW ON You can control this item when Low Pass Filter is not set to Through 5 Exit Audio Setup mode Press the VOL knob for at least 1 second 12 English Speaker Setting Fine tuning so that the System Q value is optimal when setting the speaker type 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Speaker Setting mode Pres
38. h copy protection cannot be played Audio files cannot be played depending on the encoding software setting USB device type and or recording conditions The unit may not be compatible with upgrade of compression format standard and additional specifications For details on the formats used for USB devices and restrictions refer to http www kenwood mediamanager jp Playable AAC file m4a file encoded by AAC LC format Refer to http www kenwood mediamanager jp for the details Playable MP3 file MPEG 1 2 Audio Layer 3 file Transfer bit rate 8 320 kbps Sampling frequency 16 22 05 24 32 44 1 48 kHz Playable WMA file The file in accordance with Windows Media Audio Except for the file for Windows Media Player 9 or after which applies the new functions Transfer bit rate 48 192 kbps Sampling frequency 32 44 1 48 kHz Playable Storage media CD ROM CD R CD RW USB device CD RW discs which are quick formatted by the writing software cannot be used When recording to the maximum CD R RW media capacity at once the writing software is set to Disc at once For details on the available USB devices refer to lt About USB device gt page 7 8 English Playable CD R RW format ISO 9660 Level 1 2 Joliet Romeo Long file name Playable file format of USB device For the formats supported by USB devices refer to http www kenwood mediamanager jp
39. he console has a lid make sure to install the unit so that the faceplate does not hit the lid when closing and opening Mount the unit so that the mounting angle is 30 or less Connecting Wires to Terminals KDC W6534U USB connector ED Do not remove the cap when you do not use the USB cable The connector will cause the unit to malfunction if it gets in touch with any metallic part of the vehicle Rear left output White Sub Woofer left output White Rear right output Red Sub Woofer right output Red f AUX right input Red AUX left input White SUB WOOFER Antenna Conversion Adaptor FM AM antenna ISO JASO Accessory input f Front left output White Front right output Red Fuse 10A To Kenwood disc changer External optional accessory Wiring harness Accessory ED To connect these leads refer to the relevant instruction manuals TEL mute wire Brown Connect to the terminal that is grounded when either the telephone rings or during conversation To connect the Kenwood navigation system consult If no connections are made do your navigation manual not let the wire come out from the tab Power control Motor antenna control wire Connect either to the power Blue White control terminal when using the optional power amplifier or to ANTCONT 1 the antenna control terminal in ee
40. he same RDS network with better reception Auto TP Seek When the TI function is ON and the reception is poor while listening to a traffic information station another traffic information station with better reception will be searched for automatically Display Setting AF ON The AF function is ON Display Setting AF OFF The AF function is OFF ATPS ON The Auto TP Seek Function is ON ATPS OFF The Auto TP Seek Function is OFF When the AF function is ON the RDS indicator is ON When no other stations with stronger reception are available for the same program in the RDS network you may hear the incoming broadcast in bits and snatches Turn OFF the AF function in such a case Restricting RDS Region Region Restrict Function You can choose whether or not to restrict the RDS channels received with the AF function for a particular network to a specific region Display Setting REG ON The Region Restrict Function is ON REG OFF The Region Restrict Function is OFF If AF function is not restricted to the specified region and network the AF function sets up to search the station with good reception in the same RDS network 32 English In FM reception Monaural Reception You can reduce the noise when stereo broadcasts are received as monaural Display Setting MONO OFF The monaural reception is OFF MONO ON The monaural reception is ON Function of the
41. ifferent speaker The Touch Sensor Tone doesn t sound W The preout jack is being used te The Touch Sensor Tone can t be output from the preout jack The Dimmer function doesn t work Y The Dimmer wire isn t connected correctly te Check the Dimmer wire connection Y The lt Dimmer gt page 30 is OFF te Turn it ON The display blacks out while scrolling Y lt Display Illumination Control gt is set to OFF te Refer to lt Display Illumination Control gt page 29 Even though Synchronize Clock is ON the clock can t be adjusted W The received RDS station isn t sending time data t Receive another RDS station Tuner source Radio reception is poor W The car antenna is not extended t Pull the antenna out all the way Y The antenna control wire is not connected t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt page 37 38 It isn t the set Traffic information sound volume WV The set sound volume is less than the tuner sound volume ts f the tuner sound volume is louder than the set sound volume the tuner sound volume is used Disc source AUX EXT is displayed without achieving External disc control mode VY Unsupported disc changer is connected te Use the disc changer mentioned in the lt About CD players disc changers connected to this unit gt page 3 of the section on lt Safety precautions gt
42. ilable Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off 1 Refer to the section lt Removing the hard rubber frame gt page 41 and then remove the hard rubber frame 2 Drop open the faceplate by pressing the Release button 40 English 3 Tighten the screw 2 x 5 mm Accessory and bracket Accessory in the hole shown on the diagram Accessory Accessory g A 4 Tighten the screw 2 x 5 mm Accessory and bracket Accessory in the hole shown on the diagram Never insert the screws in any other screw hole than the one specified If you screw them in another hole it will contact and may cause damage to the mechanical parts inside the unit Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Accessory Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner Removing the Unit 1 Refer to the section lt Removing the hard rubber frame gt page 41 and then remove the hard r
43. ing SCL MANU Doesn t scroll SCL AUTO Scrolls when the display changes The text scrolled is listed below CD text Folder name File name Song title Artist name Album name MD title Radio text Function of the KDC W6534U In Standby mode Built in Auxiliary input Setting Set the Built in Auxiliary Input function Display Setting AUX OFF When selecting the source there s no Auxiliary Input AUX ON When selecting the source there s Auxiliary Input In Standby mode Power OFF Timer Setting the timer to turn this unit s power OFF automatically when Standby mode continues Using this setting can save the vehicle s battery power Display Setting OFF Power OFF Timer function is OFF OFF 20M Turns the power OFF after 20 minutes Original setting OFF 40M Turns the power OFF after 40 minutes OFF 60M Turns the power OFF after 60 minutes Do this setting after setting lt Security Code gt page 28 English 33 Menu system In Standby mode CD Read Setting When there is a problem with playing a CD with special format this setting plays the CD by force Display Setting CD READ1 Play CD and Audio file CD READ2 Play CD by force Setting CD READ2 cannot play Audio file Some music CDs may not play even in the CD READ2 mode Function of the KDC W6534U Function of ACDrive media Voice Index Setting the anno
44. k Adjustment gt etc are entered step by step English 27 Menu system Function of the KDC W6534U KDC W5534U In Standby mode Security Code Activating the Security Code disables the usage of audio unit by someone else Once the Security Code is activated the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle Indication of this Security Code activation prevents your precious audio unit from stealing Set the Security Code when the lt Demonstration mode Setting gt page 35 is set to OFF When you activate the Security Code function it cannot be released Note your Security Code is the 4 digit number entered in your Car Audio Passport in this package 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Menu mode Press the MENU button for at least 1 second When MENU is displayed CODE SET is also displayed 3 Enter Security Code mode Press the Control knob for at least 1 second When ENTER is displayed CODE is also displayed 4 Select the digits to enter Push the Control knob towards ka a or gt gt 5 Select the Security Code numbers Push the Control knob towards FM or AM 6 Repeat steps 4 and 5 and complete the Security Code 7 Confirm the Security Code Press the Control knob for at least 3 seconds When RE ENTER is displayed CODE is also displayed 8 Do the step 4 through 7 step
45. ked with the ignition and the A 4 pin yellow is connected to the constant power supply Ignition cable Red A 7 Pin Red Unit Vehicle Battery cable Yellow A 4 Pin Yellow N The A 7 pin red of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin yellow is linked to the ignition Ignition cable Red A 7 Pin Red Unit Vehicle Battery cable Yellow A 4 Pin Yellow w The A 4 pin yellow of the vehicle s ISO connector is not connected to anything while the A 7 pin red is connected to the constant power supply or both the A 7 red and A 4 yellow pins are connected to the constant power supply Ignition cable Red gt Unit pe gt Battery cable Yellow When the connection is made as in 3 above the unit s power will not be linked to the ignition key For that reason always make sure to turn off the unit s power when the ignition is turned off To link the unit s power to the ignition connect the ignition cable ACC red to a power source that can be turned on and off with the ignition key A 7 Pin Red Vehicle A 4 Pin Yellow English 39 Installation Installation Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw commercially ava
46. late in until it clicks The faceplate is locked in place allowing you to use the unit 14 English TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The audio system pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON To use the TEL Mute feature you need to hook up the MUTE wire to your telephone using a commercial telephone accessory Refer to lt Connecting Wires to Terminals gt page 37 38 Tuner features KENWOOD Em asi Omm AME i A Control knob scan Am asw s ARM REP RSEL Le e e E Band display ST indicator Tuning Selecting the station 1 Select tuner source Press the SRC button Select the TUNER display 2 Select the band Push the Control knob towards FM or AM Each time you push the knob toward FM it switches between the FM1 FM2 and FM3 bands 3 Tune up or down band Push the Control knob towards ka a or gt gt During reception of stereo stations the ST indicator is ON Frequency display Preset station number Station Preset
47. loth A Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erase characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a clean soft dry cloth Before using this unit for the first time This unit is initially set on the Demonstration mode When using this unit for the first time cancel the lt Demonstration mode Setting gt page 35 About Media Manager of PC application attached to KDC W6534U Media Manager is recorded in the CD ROM attached to this unit Refer to the attached installation manual for the installation method of Media Manager Refer to the user s manual recorded in the installation CD ROM and Help of Media Manager or the operation method of Media Manager The unit can play CD USB device hereafter called ACDrive media created by Media Manager Refer to the following site for the updated information of Media Manager http www kenwood mediamanager jp Contact Kenwood for the function and operation of the Media Manager Media Manager is a product of PhatNoise About DAB Tuner control Refer to A group on the Instruction manual of DAB Tuner KTC 9090DAB optional accessory for the control method of DAB Tuner function However the following control methods of th
48. n mode Setting Sets the demonstration mode 1 Select the Demonstration mode Push the Control knob towards FM or AM Select the DEMO display 2 Set the Demonstration mode Press the Control knob for at least 2 seconds Each time you press the knob at least 2 seconds the Demonstration mode alternates between the settings shown in the table below Display Setting DEMO ON The Demonstration mode function is ON DEMO OFF Exit Demonstration mode Normal mode English 35 Accessories Installation Procedure Accessories T 1 oin 2 P A PEOTI 1 Om sien 2 Installation Procedure 1 To prevent short circuits remove the key from the ignition and disconnect the terminal of the battery 2 Make the proper input and output wire connections for each unit 3 Connect the wire on the wiring harness 4 Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle 5 Take Connector A on the wiring harness and connect it to the external power connector on your vehicle 6 Connect the wiring harness connector to the unit 36 English 7 Install the unit in your car 8 Reconnect the terminal of the battery 9 Press the reset button A If the power is not turned ON or it is ON but will be OFF immediately the speaker wire may have a short circuit or touched the chasis of the vehicle
49. nnecting a cable whose total length is longer than 5 m can result in abnormal playback You cannot connect a USB device via a USB hub A Install the USB device in the place where it will not prevent you from driving your vehicle properly Do not leave the USB device in the vehicle for a long time It can deform or damage due to direct sunlight high temperature etc Take backups of the audio files used with this unit The files can be erased depending on the operating conditions of the USB device We shall have no compensation for any damage arising out of erasure of the stored data About USB device Operation USB device operation is the same as audio file operation unless otherwise some notice is indicated USB source is recognized as CD source on the connected unit English 7 About AAC MP3 and WMA The playable AAC MP3 WMA file hereafter called Audio file and the media format has the following limitation The Audio file which is not conforming to the specification may not play normally or the file and folder names may not display correctly Playable Audio file AAC MP3 WMA AN Attach the correct extension for the Audio file AAC M4A MP3 MP3 WMA WMA Do not attach the extensions to files other than the Audio file If the extension is attached the file which is not the Audio file will play and outputs a loud noise causing damage to the speaker The files wit
50. onment The marking of products using lasers Except for some areas CLASS 1 LASER PRODUCT The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class There is no danger of hazardous radiation outside the unit English 5 About CDs Handling CDs Do not touch the recording surface of the CD CD R and CD RW are easier to damage than a normal music CD Use a CD R or a CD RW after reading the caution items on the package etc Do not stick tape etc on the CD or use a CD with tape stuck on it When using a new CD If the CD center hole or outside rim has burrs use the CD only after removing the burrs with a ballpoint pen etc CD accessories Do not use disc type accessories CD cleaning Clean from the center of the disc and move outward Ww 6 English Removing CDs When removing CDs from this unit pull them out horizontally CDs that cannot be used CDs that are not round cannot be used CDs with coloring on the recording surface or CDs hat are dirty cannot be used This unit can only play the CDs with cms Ces es This un y not correctly play discs which do not have the mark You cannot play a CD R or CD RW that has not been finalized For the finalization process refer to your CD R CD RW writing software and your CD R CD RW r
51. ontrol knob towards ka a or gt gt If the remote control with number buttons is used as optional accessories you can directly select a song you want to listen to with the operation below KDC W6534U W5534U only 1 Enter a track file number Press the number buttons on the remote control 2 Do the Track File Search Push the Control knob towards ka a or gt gt You can select Direct File Search up to 999 Function of disc changer Audio file Disc Search Folder Search Selecting the disc set in the Disc changer or the folder recorded on the Audio file media Push the Control knob towards FM or AM 22 English Track File Disc Folder Repeat Replaying the song disc in the Disc changer or Audio file folder you are listening to Press the REP button Each time you press the button the Repeat Play alternates between the modes shown in the ables below In CD amp External disc source Repeat play Display rack Repeat TRAC REP isc Repeat In Disc Changer DISC REP OFF REP OFF In Audio file source Repeat play Display File Repeat FILE REP Folder Repeat FOLD REP OFF REP OFF Scan Play Playing the first part of each song on the disc or Audio file folder you are listening to and searching for the song you want to hear 1 Start Scan Play Press the SCAN button TRAC SCN FILE SCN SCAN ON is displayed 2 Release it when the song you w
52. operation and reenter the security code APPROVED is displayed The Security Code function activates 28 English Ifyou enter a code different from your Security Code you have to start over from step 4 Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON 2 Do the step 4 through 7 step operation and reenter the security code APPROVED is displayed Now you can use the unit Ifan incorrect code is entered WAITING is displayed and the input prohibition periods shown in the table below is generated After the input prohibition time lapses CODE is displayed and you can reenter the code Number of times the Input prohibited time incorrect code was input 1 2 5 minutes 3 1 hour 4 24 hours In Standby mode Touch Sensor Tone Setting the operation check sound beep sound ON OFF Display Setting BEEP ON Beep is heard BEEP OFF Beep canceled In Standby mode Manual Clock Adjustment You can do this adjustment when the lt Synchronize Clock gt page 29 is set as OFF 1 Select Clock Adjustment mode Push the Control knob towards FM or AM Select the CLK ADJ display 2 Enter Clock Adjust mode Press the Control knob for at least 1 second The clock display blinks 3 Adjust the hours Push the Control knob towards FM or AM Adju
53. s the VOL knob 3 Select the Speaker type Turn the VOL knob Each time you turn the knob the setting alternates between the settings shown in the able below Speaker type Display OFF SP OFF For 5 amp 4 in speaker SP 5 4 For 6 amp 6x9 in speaker SP 6 9 6 For the OEM speaker SP OEM 4 Exit Speaker Setting mode Press the VOL knob Function of the KDC W6534U Subwoofer Output Turning the Subwoofer output ON or OFF Push the Control knob toward AM for at least 2 seconds Each time you push the knob Subwoofer output switches ON and OFF When it is ON SW ON is displayed You can control this function when lt Switching preout gt page 30 is set to SWPRE SW Switching Display Changing the information displayed 1 Enter Switching Display mode Press the Control knob for at least 1 second DISP SEL is displayed 2 Select the Display item Push the Control knob towards a a or gt In Tuner source Information Display Program Service name or Frequency FREQ PS FM Radio text Program Service name or R TEXT Frequency FM Frequency MW LW FREQ Clock CLOCK In CD amp External disc source Information Display Disc title D TITLE Track title T TITLE Track number amp Play time P TIME Clock CLOCK In Audio file source Information Display Song title amp Artist name TITLE
54. st the minutes Push the Control knob towards lt lt or gt gt 4 Exit Clock adjustment mode Press the MENU button In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit s clock Display Setting SYNC ON Synchronizes the time SYNC OFF Adjust the time manually It takes 3 to 4 minutes to synchronize the clock In Standby mode DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potential thieves Display Setting DSI ON LED flashes DSI OFF LED OFF Function of the KDC W6534U KDC W5534U In Standby mode Selectable Illumination Selecting the button illumination color as green or red Display Setting KEY RED The illumination color is red KEY GRN The illumination color is green Display Illumination Control This function turns off the display when you perform no operation for 5 seconds This function is effective when you are driving at night Display Setting DISP ON Keeps the display on DISP OFF Turns off the display when you perform no operation for 5 seconds Set the Display Illumination Control when the lt Demonstration mode Setting gt page 35 is set to OFF When the display is off pressing any key will turn on the display When the display is off you cannot perform any operation except for the following Volume
55. tains playable audio files is only displayed 1 Enter Folder Select 2 mode Press the F SEL button Select the FLD SEL2 display Refer to lt Select mode gt page 23 Folder name display Displays the current folder name 2 Select the folder Push the Control knob towards ka a or gt gt Each time you push the knob the folders containing audio files are displayed one after another Check the name of upper level folder Push the Control knob towards FM or AM With the FM button the folder name in the upper level is displayed With the AM button the folder name in the lower level is displayed 4f is displayed while the upper level folder is displayed 3 Decide the folder to play Press the Control knob The Folder Select mode releases and the Audio file in the folder being displayed plays Function of the KDC W6534U Function of ACDrive media Switching the Play mode Arrange the playing orders of the songs by categories Press the S MODE button Each time you press the button the Play mode alternates between the modes shown in the table below The Play mode indicator is ON Play mode Category which is to be arranged P LIST Play list order GENRE By genre ARTIST By artist ALBUM By album FOLDER By the folder recorded in media The category information of each song is the data registered in Media Manager when ACDrive media is being genera
56. ted You can cancel the announcement made when the mode is changed by lt Voice Index gt page 34 You can select the advancement of the Play mode information by AM and FM knob English 25 CD USB device Audio file External disc control features Function of the KDC W6534U Function of ACDrive media Letter Seek You can search for the song you want to play by selecting the initial of Genre name Artist name or Album name 1 Enter the Letter Seek mode Press the S MODE button for at least 1 second This operation does not function when lt All Random Play gt page 23 is ON This function is available only when the Play mode is set Genre Artist or Album Cancelling the Letter Seek Press the S MODE button 2 Start the Letter Seek Push the Control knob towards ka a or D gt The initial of Genre name Artist name or Album name is displayed and announced in order The announcement of the initial can be canceled by lt Voice Index gt page 34 When you push the Control knob to the reverse ka a or gt during Letter Seek the initial is displayed and announced in the reversed order Once Letter Seek starts it cannot be cancelled 3 Select the song to play Press the Control knob when the initial of the song you are searching is displayed and announced The selected initial group plays 26 English Text Title Scroll Scrolling the displayed CD text or MD title
57. the AM button 10 songs down You can select File Select mode up to 999 3 Decide the file to play Press the Control knob The File Select mode releases and the Audio file being displayed plays 24 English Function of Audio file Folder Select 1 mode Select the target folder by tracing the hierarchical levels of folders This is convenient when managing audio files by folder 1 Enter Folder Select 1 mode Press the F SEL button Select the FLD SEL1 FLD SEL display Refer to lt Select mode gt page 23 Folder name display Displays the current folder name 2 Select the folder level Push the Control knob towards FM or AM With the FM button you move 1 level down and with the AM button 1 level up Selecting a folder in the same level Push the Control knob towards lt lt or gt gt With the ka a of the Control knob you move to the previous folder and with the gt i of the Control knob to the next folder Returning to the top level Press the 3 button You cannot operate this function when lt Switching the Play mode gt page 25 is set to other than FOLDER while playing ACDrive media 3 Decide the folder to play Press the Control knob The Folder Select mode releases and the Audio file in the folder being displayed plays Function of Audio file Folder Select 2 mode Select the target folder within the folders containing audio files The folder which con
58. the optional power amplifier or to 1 ANTCONT the antenna control terminal in D the vehicle Battery wire Yellow Ignition wire Red See next page A 7 Pin Red E A 4 Pin Yellow Connector A Connector B 38 English Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A 4 A 5 A 6 A 7 A 8 Yellow Blue White Orange White Red Black Battery ower Control Dimmer gnition ACC Earth Ground Connection Speaker Connector B 1 B 2 B 3 B 4 B 5 B 6 B 7 B 8 Purple Purple Black Gray Gray Black White White Black Green Green Black Rear Right Rear Right Front Right Front Right Front Left Front Left Rear Left Rear Left AWARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive Make sure to make the proper connections to prevent damage to the unit The default connection for the wiring harness is described in 1 below If the ISO connector pins are set as described in 2 or 3 make the connection as illustrated lease be sure to reconnect the cable as shown 2 below o install this unit to the Volkswagen vehicles e N Default setting The A 7 pin red of the vehicle s ISO connector is lin
59. ubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown Screw M4X8 commercially available Accessory Removal tool 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it English 41 Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General The power does not turn ON Y The fuse has blown te After checking for short circuits in the wires replace the fuse with one with the same rating No sound can be heard or the volume is low Y The fader or balance settings are set all the way to one side t Center the fader and balance settings VY The input output wires or wiring harness are connected incorrectly t Reconnect the input output wires or the wiring harness correctly See the section on lt Connecting Wires to Terminals gt page 37 38 VW The values of Volume offset are low ts Turn up the Volume offset referring to the section on lt Audio Setup gt page 12 There s a source you can t switch Y There s no media inserted te
60. uncement during the play of ACDrive media Display Setting V ID ON Guide is announced V ID OFF Not be announced In CD USB mode Firmware version display Displaying the firmware version with the unit 1 Select the firmware version display mode Push the Control knob towards FM or AM Select the ACD VER F W VER display 2 Display the firmware version Push the Control knob towards lt lt or gt gt 34 English Function of the KDC W6534U In CD USB mode Unique ID display Displaying the serial number for each product 1 Select the unique ID display mode Push the Control knob towards FM or AM Select the ACD ID display 2 Display the unique ID Push the Control knob towards ka a or gt gt Function of the KDC W6534U Other than Standby mode Audio Preset Memory Registering the value setup by Sound Control The memory cannot be erased by the Reset button 1 Setup Sound Control Refer to the following operations to setup the Sound Control lt Audio Control gt page 11 lt Audio Setup gt page 12 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Audio Preset mode Push the Control knob towards FM or AM Select the A PRESET display 4 Enter Audio Preset mode Press the Control knob for at least 1 second 5 Select the Audio Preset Memory Push the Control knob towards FM or AM Select the MEMOR

Kenwood KDC-PS9070R Car Stereo System User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents