Home

Kenwood KDC-MPV8025 Car Stereo System User Manual

1. AM Button FM Button When Folder Select is selected with file S being played to move from folder to folder Operation of the button Haa Button bP Button AM Button FM Button English 9 Notes on Multi function Key System Multi function Key System serves to control various functions with the 2 5 buttons The basic operation of the Multi function Key System is described below What s the Multi function Key System This unit is equipped with the Multi function Key System that enables the operation of multiple unctions with one button For example you can enter the Display Control Mode or turn ON OFF the Random Play by pressing he 3 button during CD play Setting each function The function display will show the controllable unction of the 2 5 button above the button Pressing the 2 5 button below the desired unction enables the setting of the function Displaying the desired function f five or more functions are available to be set with he 2 5 button they are divided into multiple unction groups referred to as sections in this manual for registration Press the NEXT button to switch the sections f the display of the desired function is not shown press the NEXT button 1 to 3 times to switch the sections until the wanted function display is shown Example Function display of CD amp External
2. ACAUTION Use of contro Is or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure In compliance with Federal Regulations following are reproduct ions of labels on or inside the product relating to laser product safety KENWOOD CORPORATION 2967 3 ISHI KAWA CHO HACHIOJI SHI TOKYO JAPAN KENWOOD CORP CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS NO 21 CFR 1040 10 CHAPTER 1 SUBCHAPTER J he authority unauthorized NOTE comply with pursuant to P are designed against harm Location Bottom Panel FCC WARNING This equipment may generate or use radio requency energy Changes or modifications to his equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual The user could lose to operate this equipment if an change or modification is made This equipment has been tested and found to he limits for a Class B digital device art 15 of the FCC Rules These limits to provide reasonable protection ul interference in a residentia installation This equipment may cause harmful interference t o radio communications if it is not installed and used in accordance with the instructions that interference will not occur in a particular However there is no guarantee installation interference t this equipment does cau
3. Direct Disc Search page 23 enter the track file disc number In SIRIUS tuner source FM buttons Select the preset band lt gt gt buttons Search up or down channel 0 9 buttons Press buttons 1 6 to recall preset channels DIRECT OK button Enters and cancels the Direct Access Tuning page 27 mode In HD Radio source FM button Select the HF band Each time the FM button is pressed it switches between the HF1 HF2 and HF3 bands AM button Select the HA band lt gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations English 37 Accessories Installation Procedure Accessories OOO O OOO OO 2 3 ia 4 op Seventies 4 D EEA 2 38 English Installation Procedure 1 To prevent a short circuit remove the key from he ignition and disconnect the battery 2 Make the proper input and output wire connections for each unit 3 Connect the speaker wires of the wiring harness 4 Connect the wiring harness wires in the following order ground battery ignition 5 Connect the wiring harness connector to the unit 6 Install the unit in your car 7 Reconnect the battery 8 Turn the vehicle s ignition key on and open the panel 9 Press the 5 button and the reset button AWARNING If you connect the ig
4. Y The protection function for preventing fingers or other things from getting caught in between the panel and this unit has been activated te Turn off the power again _ The Control Panel moves although you do not desire VY The Demonstration mode has been selected ts Hold down button 5 and press the Reset button to release the Demonstration mode English 43 Troubleshooting Guide Tuner source Radio reception is poor Y The car antenna is not extended te Pull the antenna out all the way V The antenna control wire is not connected ts Connect the wire correctly referring to the section on Connecting Wires to Terminals Track Search can t be done V For the discs folders first or last song te For each disc folder Track Search can t be done in the backward direction for the first song or in the forward direction for the last song The desired frequency can t be entered with the Direct Access Tuning Y A station that can t be received is being entered ts Enter a station that can be received Y You re trying to enter a frequency with a 0 01 MHz unit ts What can be designated in the FM band is to 0 1 MHz MP3 WMA source Cannot play an MP3 WMA WY The media is scratched or dirty ts Clean the media referring to the CD cleaning of the section on About CDs page 7 Disc source AUX EXT is displayed without achieving External disc control mode Y
5. 20dB 28 dBu 25 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed 1000 400 rpm CLV 2times Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 01 Signal to Noise ratio 1 kHz 105 dB Dynamic range 93 dB Channel separation 95 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio 46 English Audio section Maximum output power 50Wx4 Full Bandwidth Power at less than 1 THD 22Wx4 Tone action Bass 100 Hz 8 dB Middle 1 kHz 8 dB Treble 12 5 kHz 8 dB Preout level Load during disc play 2000 mV 10 kQ Preout impedance lt 6000 Auxiliary input KDC MPV8025 Frequency response 1 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input Impedance 100 kQ General Operating voltage 11 16V allowable 144V Current consumption 10A Installation Size W x H x D 182 x 53 x 162 mm 7 3 16 x 2 1 16 x 6 3 8 inch Weight 4 19 Ibs 1 9 kg
6. Slide the cover while pressing downwards to Adjusting the volume remove it as illustrated ISRC button Insert the batteries with the and poles aligned Each time the button is pressed the source properly following the illustration inside the case eqitches For the source switching order refer to Selecting the Source page 12 ATT button Turning the volume down quickly When it is pressed again it returns to the previous level AWARNING Store unused batteries out of the reach of children Contact a doctor immediately if the battery is accidentally swallowed AN Do not set the remote on hot places such as above the dashboard 36 English In Tuner source FM AM buttons Select the band Each time the FM button is pressed it switches between the FM1 FM2 and FM3 bands lt lt 4 gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations DIRECT OK button Enters and cancels the Direct Access Tuning page 21 mode In Disc source lt lt 4 gt gt buttons Doing track file forward and backward DISC DISC buttons Doing disc folder forward and backward gt 11 button Each time the button is pressed the song pauses and plays DNPP button Enters and cancels the DNPP Disc Name Preset Play page 25 mode 0 9 buttons When in Direct Track File Search page 23 and
7. aximum number of characters for folder name 64 Joliet Up to 32 characters are displayed For a list of available characters see the instruction manual of the writing software and the section Entering file and folder names below The media reproducible on this unit has the following limitations Maximum number of directory levels 8 Maximum number of files per folder 255 Maximum number of folders 50 Maximum number of files and folders 512 MP3 WMA written in the formats other than the above may not be successfully played and their file names or folder names are not properly displayed Settings for your MP3 WMA encoder and CD writer Do the following setting when compressing audio data in MP3 WMA data with the MP3 WMA encoder Transfer bit rate MP3 8 320 kbps WMA 48 192 kbps Sampling frequency MP3 8 11 025 12 16 22 05 24 32 44 1 48 kHz WMA 32 44 1 48 kHz When you use your CD writer to record MP3 WMA up to the maximum disc capacity disable additional writing For recording on an empty disc up to the maximum capacity at once check Disc at Once 8 English Play mode may not be possible when portions of the functions of Windows Media Player 9 or higher are used Entering ID3 tag The Displayable ID3 tag is ID3 version 1 x For the character code refer to the List of
8. kaa or gt gt button Canceling Direct Track File Search Press the gt I button Function of disc changers with remote Direct Disc Search Doing Disc Search by entering the disc number 1 Enter the disc number Press the number buttons on the remote 2 Do Disc Search Press the DISC or DISC button Canceling Direct Disc Search Press the gt I button Input 0 to select disc 10 English 23 CD MP3 WMA External disc control features Track File Disc Folder Repeat Replaying the song disc in the Disc changer or MP3 WMA folder you re listening to 1 Select the key function section Press the NEXT button Repeatedly press the button until REP is displayed above the 4 button Refer to Notes on Multi function Key System page 10 2 Turn ON OFF the Repeat Play Press the 4 REP button Each time the button is pressed the Repeat Play switches as shown below In CD amp External disc source Repeat play Display Track Repeat T Repeat ON Disc Repeat In Disc Changer D Repeat ON OFF Repeat OFF In MP3 WMA source Repeat play Display File Repeat File REP ON Folder Repeat FOLD REP ON OFF Repeat OFF Scan Play Playing the first part of each song on the disc or MP3 WMA folder you are listening to and searching for the song you want to listen to 1 Select the key function section Press the NEXT button Repeat to press the button until
9. 2 5 button Refer to Notes on Multi function Key System page 10 3 Call up the station Press the desired 1 6 button English 21 CD MP3 WMA External disc control features gt il SCRL DISC DISC Haa Liai AM FM Track number IN indicator Disc number Track time Playing CD amp MP3 WMA Each time the button is pressed the song pauses Te a or plays When there is no disc inserted Eject the disc 1 Open the panel to insert disc 1 Eject the di Press the 4 button names te Press the 4 button 2 Insert a disc 2 Return the panel to the original position A Press the 4 button When the faceplate has been slid open it might interfere with the shift lever or something else If this happens pay attention to safety and move the shift 3 in 8cm disc can t be played Using an adapter and lever or take an appropriate action then operate the inserting them into this unit can cause damage unit The MP3 WMA media that this unit can play are CD ROM CD R and CD RW The sound will be temporarily muted while the The medium formats must be ISO 9660 Level 1 Level faceplate is moving lt When a disc is inserted the IN indicator is ON 2 Joliet or Romeo The methods and precautions to be followed for writing MP3 WMA data are covered When a disc is inserted in Notes on playing MP3 WMA page 8 Check that Press the SRC button section before cre
10. 5 button Each time the button is pressed the setting switches as shown below Speaker type Button Display OFF 2 OFF For 5 amp 4 in speaker B 5 4 For 6 amp 6x9 in speaker 4 69 6 For the OEM speaker 5 OEM 4 Exit Speaker Setting mode Press the Q button Subwoofer Output Turning the Subwoofer output ON or OFF Press the SW button for at least 1 second Each time the button is pressed Subwoofer output switches ON or OFF When it s ON Sub W ON is displayed You can control this function when Switching preout page 34 is set to SWPRE Sub W Function of the KDC MPV8025 In SIRIUS Tuner External disc or Auxiliary input source Dual Zone System Makes the sound different for the front channel and rear channel Output the Internal source sound from either one of the front or rear channels and the sound of other source from the Dual zone channel 1 Select the source Press the SRC button Select the source sound to be output from the Dual zone channel 2 Select the key function section Press the NEXT button Repeatedly press the button until 2 ZN is displayed above the 5 button Refer to Notes on Multi function Key System page 10 3 Enter the Dual Zone System Control mode Press the 5 2 ZN button 4 Select the item for adjustment Press the desired 2 3 button Each time the button is pressed the items that can be adjusted switch as shown
11. Codes 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 oj jP P m Alp ala 1 lafa a a il l N 2 2 B R b r e FTA l l 3 3 C Sj cj s A 6 al 6 4 4 D T d t al AO al 5 5 E u e u HALO alo 6 amp 6 FIVi flv i1 Of 6 7 7 G W 9 w x el 8 a H X h x d TLE Ol 9 digttfylily E u lu A J Z iz a ej B KI E k l l l l a c delli afa if oli a D M m ofm ily E gt N 4 n 4 T P i P F O _ o m l i Bl ily Entering file and folder names The code list characters are the only file names and folder names that can be entered and displayed If you use any other character for entry the file and folder names are not displayed correctly They may neither be displayed correctly depending on the CD writer used The unit recognizes and plays only those MP3 WMA which have the MP3 WMA extension MP3 WMA A file with a name entered with characters not on the code list may not play correctly Writing files into a medium When a medium containing MP3 WMA data is oaded the unit checks all the data on the medium f the medium contains a lot of folders or non MP3 WMA files therefore it takes a long time until the unit starts playing MP3 WMA n addition it may take time for the unit to move o the next MP3 WMA file or a File Search or Folder Search may not be performed smoothly A Loading such a medium may produce loud noise to da
12. Mode Switching Switching the display mode 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 DISP button 3 Select the display mode Press the 2 MODE button Each time the button is pressed the display mode switches as shown below Display Display Mode Display C Demonstration Display A Normal display type Display B Silent display type 4 Exit display control mode Press the 6 button English 15 General features Text Display Switching Switching the text display 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 DISP button 3 Select the text Press the 3 TEXT button It can also be switched by pressing either lt 4 or gt button In Tuner source Information Display Station name or Frequency BAND SNPS Frequency BAND FREQ Clock Clock In CD amp External disc source Information Display Disc title D TITLE Track title TITLE Track number amp Play time P Time Disc
13. Unsupported disc changer is connected ts Use the disc changer mentioned in the About CD players disc changers connected to this unit page 5 of the section on Safety precautions The sound skips when an MP3 WMA is being played WY The media is scratched or dirty ts Clean the media referring to the CD cleaning of the section on About CDs page 7 Y The recording condition is bad ts Record the media again or use another media The specified disc does not play but another one plays instead Y The specified CD is quite dirty t Clean the CD The MP3 WMA track time isn t displayed correctly a ts There are times when it isn t displayed correctly according to the MP3 WMA recording conditions WV The disc is loaded in a different slot from that specified te Eject the disc magazine and check the number for the specified disc SN he disc is severely scratched ts Try another disc instead A CD ejects as soon as it is loaded Y The CD is quite dirty ts Clean the CD referring to the CD cleaning of the section on About CDs page 7 Can t remove disc Y The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF ts The disc can only be removed within 10 minutes of the ACC switch being turned OFF f more than 10 minutes has elapsed turn he ACC switch ON again and press the Eject button The disc won t inse
14. below Adjustment Item Button _ Display Range Dual Zone System 2 ON OFF ON OFF Dual Zone System B F R Front Rear Front amp Rear Dual Zone System Rear The front is this unit s internal source and the rear is selected source sound Dual Zone System Front The rear is this unit s internal source and the front is selected source sound 5 Exit the Dual Zone System Control mode Press the 6 button 6 Select the source Press the SRC button Select the source sound to be output from the internal source channel The Dual Zone System can be used with the sources shown below Internal auxiliary input KCA S210A CA C1AX External disc changer player SIRIUS satellite radio tuner While Dual Zone System is ON the setting of Dual Zone System Front or Rear is disabled Set Dual Zone System Front or Rear first and then set the Dual Zone System to ON When the Dual Zone System is ON there is no Dual zone channel audio control or other effect When you use the Dual Zone System by selecting the optional accessory source for the output of the Dual zone channel you cannot select another optional accessory source as the source for the Internal source channel When you set the Dual zone system to ON while the sub woofer preout is switched ON the sound of the sub woofer preout isn t output The Dual Zone System cannot be used if a DAB control unit is connected Display
15. damaged or broken due to shock The liquid crystal fluid may be dangerous to your health or even fatal If the liquid crystal fluid from the LCD contacts your body or clothing wash it off with soap immediately a wa 4 English ACAUTION To prevent damage to the machine take the following precautions Make sure to ground the unit to a negative 12V DC power supply Do not open the top or bottom covers of the unit Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not set the removed faceplate or the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing To prevent deterioration do not touch the erminals of the unit or faceplate with your ingers Do not subject the faceplate to excessive shock as it is a piece of precision equipment When replacing a fuse only use a new one with he prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction To prevent a short circuit when replacing a fuse irst disconnect the wiring harness Do not place any object between the faceplate and the unit Do not apply excessive force to the moving aceplate Doing so will cause damage or malfunction Do not apply excessive force to the open a
16. name DNPS Clock Clock In MP3 WMA source Information Display Song title amp Artist name TITLE Album name amp Artist name ALBUM Folder name FOLDER NAME File name FILE NAME Play time amp File number P Time Clock Clock In Auxiliary input source Information Display Auxiliary input name AUX Name Clock Clock 16 English In Standby Information Display STANDBY Clock Cock In SIRIUS tuner source Information Display Channel Name Channel Name Song Title Song Title Artist Name Artist Name Composer name Composer Category Name Category Band amp Channel Number Channel No Clock Clock In HD Radio source Information Display Station name Station Name Song title Artist name Title Album name Genre Frequency Frequency Clock Clock 4 Exit Display Control mode Press the 6 button If the Disc title Track title Song title amp Artist name or Album name amp Artist name is selected when the disc which does not have Disc title Track title Song title Album name or Artist name is played track number and play time are displayed If the text for the Sirius tuner source including Channel name etc is selected when the channel which does not have text for the Sirius tuner source including Channel name etc is played band amp channel number is displayed Function of the KDC MPV8025 Illumination Color Setting You can set the display t
17. pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON English 19 Tuner features 1 6 NEXT SRC AUTO RL MAME _ NAMES ESW DISC AUTO AME AM ST indicator Preset station number de Band display Frequency display Tuning Mode Tuning Choose the tuning mode Selecting the station Press the AUTO button Each time the button is pressed the Tuning mode switches as shown below 1 Select tuner source Press the SRC button Select the TUNER display Tuning mode Display Operation Auto seek Auto 1 Automatic search for a station 2 Select the band Preset station seek Auto 2 Search in order of the stations Press the FM or AM button a in the Preset memory Each time the FM button is pressed it switches Manual Manual Normal manual tuning control between the FM1 FM2 and FM3 bands 3 Tune up or down band Press the ka a or gt gt button is ON 20 English During reception of stereo stations the ST indicator Function of remote Direct Access Tuning Entering the frequency and tuning 1 Select the band Press the FM or AM button 2 Enter Direct Access Tuning mode Press the DIRECT button on the remote is displayed 3 Enter the
18. the Reset button and when it s removed from the battery power source 1 Turn the power ON 2 Do the step 4 through 7 operation and enter the Security Code APPROVED is displayed 32 English The unit can be used Touch Sensor Tone Setting the operation check sound beep sound ON OFF Display Setting Beep ON Beep is heard Beep OFF Beep canceled Manual Clock Adjustment 1 Select Clock Adjustment mode Press the FM or AM button Select the Clock Adjust display 2 Enter Clock Adjust mode Press the kaa or gt gt button for at least 1 second The clock display blinks 3 Adjust the hours Press the FM or AM button Adjust the minutes Press the kaa or gt gt button 4 Exit Clock adjustment mode Press the MENU button DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potential thieves Display Setting DSI ON LED flashes DSI OFF LED OFF Selectable Illumination Selecting the button illumination color as green or red OFF Wait Time Setting Setting the time until the faceplate hide operation starts after the power is turned OFF The faceplate can be removed only during the set Display Setting time period Button Red The illumination color is red Button Green The illumination color is green Display and Setting Triangle indicator setting Sets the blink
19. the shift ever or another part depending on the angles of the control panel Set the angle to avoid any interference When a hard rubber frame is mounted Do not use with the panel slid in the forward direction f so the hard rubber frame will interfere with the panel when the angle is adjusted downward o sound is produced while the panel is operating Theft Deterrent Panel The Backpanel of the unit can be detached and taken with you helping to deter theft Removing the Backpanel 1 Turn the ignition OFF or press the SRC button for at least 1 second Turn OFF the power and the control panel becomes horizontal After the set time passes in OFF Wait Time Setting page33 the panel is closed 2 Remove the Backpanel forward When DSI Disabled System Indicator page32 is set to ON DSI blinks AN The back panel is a precision piece of equipment and can be damaged by shocks or jolts For that reason keep the back panel in its special storage case while detached Do not expose the Backpanel or its storage case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Backpanel 1 Set the Backpanel to the panel bracket 2 Hold down on the Backpanel until it is locked TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The audio system
20. 41 Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Accessory 2 Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner 42 English Removing the Unit 1 Refer to the section Removing the hard rubber frame page 42 and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown Screw M4X8 commercially available Accessory Removal tool 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General The power does not turn ON VW The fuse has blown sx After checking for short circuits in the wires replace the fuse with one with the same rating VY Speaker cable touches on chassis etc te Wire or insulate the speaker ca
21. KENWOOD KDC MPV8025 KDC MP825 CD RECEIVER INSTRUCTION MANUAL KENWOOD CORPORATION Take the time to read through this instruction manual Familiarity with installation and operation procedures will help you obtain the best performance from your new CD receiver For your records Record the serial number found on the back of the unit in the spaces designated on the warranty card and in the space provided below Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product Model KDC MPV8025 KDC MP825 Serial number wise SIRIUS HW H Radio w Media DIGITAL AUDIO pau A D Y B64 2743 00 01 KV Contents Warning Safety precautions Random Play Magazine Random Play Folder Select About CDs Notes on playing MP3 WMA 3 4 Notes 6 7 8 0 Notes on Multi function Key System 1 General features 11 Power Hiding the Control Panel Selecting the Source Volume Attenuator System Q Audio Control Rotary Volume knob operation mode select Speaker Setting Subwoofer Output Dual Zone System Display Mode Switching Text Display Switching Illumination Color Setting Station Disc Naming SNPS DNPS Auxiliary Input Display Setting Panel Position Setting Theft Deterrent Panel TEL Mute Tuner features 20 Text Title Scroll DNPP Disc Name Preset Play SIRIUS tuner control features 26 Select SIRIUS Sa
22. NWOOD dealer for assistance Press the reset button if the disc auto changer fails to operate correctly Normal operation should be restored we Ie2 Jil iC C Ces NX ANE JE qE ery Reset button We recommend the use of Security Code page 32 to prevent theft Characters in the LCD may become difficult to read in temperatures below 41 F 5 C The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may represent something impossible in actual operation Lens Fogging Right after you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging CDs may be impossible to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer English 5 Notes Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe neutral deterge
23. Preset Play Selecting the CD displayed in the DNPS of the CDs set in the Disc changer 1 Enter DNPP mode Press the DNPP button on the remote When DNPP is displayed the DNPS display in order Forward Reverse display Press the DISC or DISC button 2 When the disc you want is displayed Press the OK button on the remote The disc being displayed is played Canceling the DNPP mode Press the DNPP button on the remote English 25 SIRIUS tuner control features NEXT SRC AUTO SCRL FM They LHT Select SIRIUS Satellite Radio Mode Display Operation Selecting the SIRIUS Satellite Radio Tuner Channel Normal manual seeking control Preset Search in order of the channels in the Preset optional accessory connected to this unit Selecting SIRIUS Mode Press the SRC button Select the SIRIUS display You need to subscribe to SIRIUS to receive the service by SIRIUS Satellite Radio Consult SIRIUS if CALL 888 539 SIRIUS TO SUBSCRIBE appears It may take a little time to start receiving after you selected the SIRIUS source If the signal receiving fails Acquiring Signal appears Switching Seek Mode Sets the seeking mode Press the AUTO button Each time the button is pressed the Seek mode switches as shown below 26 English memory Select the channel Selecting the channel Press the ka a or gt gt button Channel Searc
24. SCAN is displayed above the 2 button Refer to Notes on Multi function Key System page 10 2 Start Scan Play Press the 2 SCAN button Scan ON is displayed 3 Release it when the song you want to listen to is played Press the 2 button 24 English Random Play Play all the songs on the disc or MP3 WMA folder in random order 1 Select the key function section Press the NEXT button Repeatedly press the button until RDM is displayed above the 3 button Refer to Notes on Multi function Key System page 10 2 Turn ON OFF the Random Play Press the 3 RDM button Each time the button is pressed Random Play urns ON or OFF When it s ON Random ON is displayed When the bl button is pressed the next song select starts Function of disc changer Magazine Random Play Play the songs on all the discs in the disc changer in random order 1 Select the key function section Press the NEXT button Repeatedly press the button until MRDM is displayed above the 5 button Refer to Notes on Multi function Key System page 10 2 Turning ON OFF the Magazine Random Play Press the 5 MRDM button Each time the button is pressed the Magazine Random Play turns ON or OFF When it s ON M Random ON is displayed When the bl button is pressed the next song select starts Function of MP3 WMA Folder Select Quickly selecting the folder you want to liste
25. a rear output terminal After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less Connecting Wires to Terminals AUX right input Red KDC MPV8025 only pi AUX left input White KDC MPV8025 only Rear right output Red Subwoofer right output Red He Rear left output White Subwoofer left output White FM AM antenna input ans Va Ya4dOOM Fuse 10A Front right output Red Front left output White 4LNOY4 To KENWOOD disc changer Sirius satellite radio tuner External optional accessory To connect these leads refer to the relevant instruction manuals If no connections are made do not let the wire come out from the tab Wiring harness Accessory iw When using the optional power amplifier connect to its power control terminal P coNT Power control wire Blue White Depending on what antenna you are using connect either to the control terminal of the motor antenna or to the power terminal for the booster amplifier of the film type tonr_ Motor antenna control wire Blue antenna Connect to the terminal that is grounded when either the telep
26. at can t be used CDs that aren t round can t be used CDs with coloring on the recording surface or that are dirty can t be used This unit can only play the CDs with It may not correctly play discs which do not have the mark A CD R or CD RW that hasn t been finalized can t be played For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual CD storage Don t place them in direct sunlight On the seat or dashboard etc and where the temperature is high Store CDs in their cases English 7 Notes on playing MP3 WMA Note however that the MP3 WMA recording media and formats acceptable are limited When writing MP3 WMA pay attention to the following restrictions Acceptable media The MP3 WMA recording media acceptable to this unit are CD ROM CD R and CD RW When using CD RW do full format not quick format o prevent malfunction Acceptable medium formats The following formats are available for the media used in this unit The maximum number of characters used for file and folder name including he delimiter and three character extension are indicated in parentheses ISO 9660 Level 1 12 characters ISO 9660 Level 2 31 characters Joliet 64 character Up to 32 characters are displayed Romeo 128 character Up to 64 characters are displayed Long file name 200 characters Up to 64 characters are displayed
27. at least 2 seconds The presently selected AUX Name is blinks 3 Select the Auxiliary input display Press the ka a or gt gt button Each time the button is pressed it switches through the below displays AUX AUX EXT TV VIDEO GAME PORTABLE DVD 4 Exit Auxiliary input display setting mode Press the NAME S button When operation stops for 10 seconds the name at that time is selected and Auxiliary input display setting mode closes The Auxiliary Input Display can be set only when the built in auxiliary input or the auxiliary input of optional KCA S210A is used Panel Position Setting Setting the angle or back forward position of the control panel 1 Select the key function section Press the NEXT button Repeatedly press the button until PNL is displayed above the 4 button Refer to Notes on Multi function Key System page 10 2 Enter Panel Position Setting mode Press the 4 PNL button 3 Select the item for adjustment Press the desired 2 5 button 18 English Each time the button is pressed the items that can be adjusted switch as shown below Adjustment Item Button Display The panel tilts upwards 2 ANG The panel tilts downwards 3 ANG The panel slides backward 4 SLD The panel slides forward 5 SLD 4 Exit Panel Position Setting mode Press the 6 button A The control panel may be interfered with
28. ating your MP3 WMA media Select the CD display Pause and play Press the gt I button 22 English Playing External Disc Playing discs set in the optional accessory disc player connected to this unit Press the SRC button Select the display for the disc player you want Display examples Display Disc player D2 CD player CD CH CD changer MD CH MD changer Pause and play Press the gt I button Each time the button is pressed it pauses and plays Disc 10 is displayed as 0 The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected Fast Forwarding and Reversing Fast Forwarding Hold down on the gt gt button Release your finger to play the disc at that point Reversing Hold down on the ka button Release your finger to play the disc at that point Track File Search Searching for a song on the disc or in the MP3 WMA folder Press the kaa or gt gt button Function of disc changer MP3 WMA Disc Search Folder Search Selecting the disc set in the Disc changer or the folder recorded on the MP3 WMA media Press the DISC or DISC button Function of remote Direct Track File Search Doing Track File Search by entering the track file number 1 Enter the track file number Press the number buttons on the remote 2 Do Track File Search Press the
29. ble properly and press the reset button Y The Demonstration mode has been selected te Hold down button 5 and press the Reset button to release the Demonstration mode J There s a source you can t switch V There s no media inserted ts Set the media you want to listen to If there s no media in this unit you can t switch to each source No sound can be heard or the volume is low WV The fader or balance settings are set all the way to one side ts Center the fader and balance settings V The input output wires or wiring harness are connected incorrectly te Reconnect the input output wires or the wiring harness correctly See the section on Connecting Wires to Terminals v The values of Volume offset are low ts Turn up the Volume offset referring to the section on Audio Control page 12 Y The Built in Amp Mute Setting page 34 is ON c Turn it OFF Y The Disc changer isn t connected t Connect the Disc changer If the Disc changer isn t connected to it s input terminal You can t switch to an external disc source Lan The memory is erased when the ignition is turned OFF Y The ignition and battery wire are incorrectly connected ts Connect the wire correctly referring to the section on Connecting Wires to Terminals There s no loudness effect Y You re using Subwoofer preout te Loudness has no effect in Subw
30. ceplate or place objects on it Doing so will cause damage or breakdown Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit About CD players disc changers connected to this unit ENWOOD disc changers CD players released in 1998 or later can be connected to this unit Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers CD players ote that any KENWOOD disc changers CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit Unsupported connection may result in damage Setting the O N Switch to the N position for the applicable KENWOOD disc changers CD players The functions that can be used and the information hat can be displayed will differ depending on the models being connected A You can damage both your unit and the CD changer if you connect them incorrectly Do Not Load 3 in CDs in the CD slot If you try to load a 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit NOTE If you experience problems during installation consult your Kenwood dealer If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed If the unit still fails to operate properly after the Reset button has been pressed contact your local KE
31. disc source 1st section SCAN RDM REP MRDM F NEXT NEXT 2nd section AUD DISP PNL 2 ZN 3rd section NEXT H F SYNC MRDM H F SYNC or DISP are displayed when an optional accessory is connected 10 English Real operational example of the Multi function Key System Example Turning ON OFF the Random Play during CD play 1 Show the function display of the Random Play f RDM is not shown in the display press the NEXT button to switch the sections until the RDM function display is shown above the 3 button 2 Turn ON OFF the Random Play Press the 3 button Each time the 3 button under the RDM unction display is pressed the Random Play is urned ON OFF Function displaying aCe Je JC4 ICs Jl KODI SCAN RDM R P FSEL A A AUD DISP PNL 2 ZN A i ry 1 JC JC JCe ICs LEY General features SRC AUTO AME scal S 4 ENAMES _ SW DISC VOL Q indicator NAME S AM FM lt lt gt i sw ATT indicator Function display Power Turning ON the Power Turn the vehicle ignition ON The panel appears Turing OFF the Power Turn the vehicle ignition OFF or press the SRC button for at least 1 second The panel hides A Do not apply force to the panel during operation It can cause damage Hiding the Control Panel Prevents tampering with the unit while your car is b
32. do not want the hollow to be visible mount the rubber frame in the opposite direction with the flat side at the top instead of the bottom 40 English Japanese cars 1 Refer to the section Removing the hard rubber frame page 42 and then remove the hard rubber frame 2 Align the holes in the unit two locations on each side with the vehicle mounting bracket and secure the unit with the accessory screws T Toyota cars N Nissan cars N St u ES jem a E MAX m 5mm 5mm Accessory for Nissan car Accessory for Toyota car A During installation do not use any screws except for those provided The use of different screws might result in damage to the main unit Damage may occur if a screwdriver or similar tool is used with excessive force during the installations Installation Locking the Backpanel to the unit If you want to fasten the faceplate to the main unit so that it does not fall off 1 Refer to the Removing the Backpanel function of the section on Theft Deterrent Panel page 18 and remove the Backpanel 2 Insert the panel lock screws into the holes at the sides of the panel Accessory 3 Reattach the Backpanel AN Never insert the panel lock screws in any other screw holes than the one specified If you insert them in another hole it will contract and may cause damage to the mechanical parts inside the unit English
33. ease it when the song you want to listen to is received Press the AUTO button for at least 1 second Text Scroll for SIRIUS tuner source Scrolls the displayed channel name and other items Press the SCRL button 28 English HD Radio control features MENU ST indicator Preset station number L a Eg Band display Tuning Selecting the station 1 Select HD Radio source Press the SRC button Select the HD Radio display 2 Select the HF band Press the FM button Each time the FM button is pressed it switches between the HF1 HF2 and HF3 bands Select the HA band Press the AM button 3 Tune up or down band Press the lt 4 or gt gt button When you connect an HD Radio Tuner features of the unit are disabled and switched to HD Radio tuner features A portion of the setting methods including the Tuning Mode will change With the HD Radio tuner you can use the similar functions to Station Preset Memory and Preset Tuning of Tuner features Refer to Tuner features for how to use the functions Frequency display The HD Radio cannot be selected as a dual zone source English 29 HD Radio control features Auto Memory Entry Putting a station with good reception in the memory automatically 1 Select the band for Auto Memory Entry Press the FM or AM button 2 Enter Menu mode Press the MENU button for a
34. eing serviced etc Hiding the control panel Press the SRC button for at least 1 second When the time set in OFF Wait Time Setting page 33 lapses the panel is hidden and the power turns OFF Showing the control panel Press the left part at the lower side of the panel The panel is opened to enable the operation English 11 General features Selecting the Source Press the SRC button Source required Display SIRIUS tuner Optional accessory SIRIUS Tuner or HD Radio Optional accessory TUNER or HD RADIO O CD External disc Optional accessory CD CH CD2 Auxiliary input Optional accessory AUX EXT Auxiliary input KDC MPV8025 only AUX Standby Illumination only mode STANDBY Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise Attenuator Turning the volume down quickly Press the ATT button Each time the button is pressed the Attenuator turns ON or OFF When it s ON the ATT indicator blinks System Q You can recall the best sound setting preset for different types of music 1 Select the source to set Press the SRC button 2 Select the Sound type Press the Q button Each time the button is pressed the sound setting switches Sound setting Display Flat Flat User memory User Rock Roc
35. frequency Press the number buttons on the remote Example Desired frequency Press button 92 1 MHz FM 0 91 2 1 810 kHz AM 0 8 1 0 Canceling Direct Access Tuning Press the DIRECT button on the remote Station Preset Memory Putting the station in the memory 1 Select the band Press the FM or AM button 2 Select the frequency to put in the memory Press the kaa or gt gt button 3 Select the key function section Press the NEXT button Repeatedly press the button until the function item is not displayed above the 2 5 button Refer to Notes on Multi function Key System page 10 4 Put the frequency in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button Auto Memory Entry Putting stations with good reception in the memory automatically 1 Select the band for Auto Memory Entry Press the FM or AM button 2 Open Auto Memory Entry Press the AME button for at least 2 seconds When 6 stations that can be received are put in the memory Auto Memory Entry closes Preset Tuning Calling up the stations in the memory 1 Select the band Press the FM or AM button 2 Select the key function section Press the NEXT button Repeatedly press the button until the function item is not displayed above the
36. h Selecting the channel and category you want to receive 1 Select the key function section Press the NEXT button Repeatedly press the button until CH CH CS CS is displayed above the 2 5 button Refer to Notes on Multi function Key System page 10 2 Select the item for adjustment Press the desired 2 5 button Each time the button is pressed the items that can be adjusted switch as shown below Adjustment Item Button Display Search down in category 2 o Search up in category 3 G Search down for channel in selected category 4 CH Search up for channel in selected category 5 CH You cannot operate this unit until all the Category information is acquired Function of remote Direct Access Tuning Entering the channel and tuning 1 Enter Direct Access Tuning mode Press the DIRECT button on the remote 2 Enter the channel Press the number buttons 3 Do Channel Search Press the kaa or gt gt button Canceling Direct Access Tuning Press the DIRECT button on the remote If you make no button operation for 10 seconds the Direct Access Tuning mode is automatically canceled You can set up to Channel number 223 If there is no signal in the input Channel NO CH appears If you cannot receive any signal in the input Channel due to a bad condition on radio wave or another problem Acquiring Signal appears Selecting
37. he cursor to the enter character position Press the kaa or gt gt button 4 Select the character type Press the 2 4 button Each time the button is pressed the character type switches as shown below Character type Button Alphabet Upper case Lower case 2 CAPS Numbers and symbols 3 NUM Special characters Accent characters 4 CHAR 5 Select the characters Press the FM or AM button Characters can be entered by using a remote with a number buttons Example If DANCE is entered Character Button Times pressed D B 1 A 2 1 N 6 2 C 2 3 1E B 2 6 Repeat steps 3 through 5 and enter the name 7 Exit name set mode Press the NAME S button When operation stops for 10 seconds the name at that time is registered and Name Set mode closes Memory numbers FM 32 stations AM 16 stations Internal CD player 30 discs External CD changer player Varies according to the CD changer player Refer to the CD changer player manual The title of station CD can be changed by the same operation used to name it English 17 General features Auxiliary Input Display Setting Selecting the display when this device is switched to Auxiliary input source 1 Select Auxiliary input source Press the SRC button Select the AUX AUX EXT display 2 Enter Auxiliary input display setting mode Press the NAME S button for
38. hone rings or during conversation EME TEL mute wire Brown To car light control switch j HUM _ Dimmer control wire Orange White To front left spea White Black FRONT LI White To front right spea Gray Black Faont A FRONT R Gray To rear left spea re Green Black Green To rear right spea xO Purple Black gasp REAR R Purple Ignition key switch t Cat fase bo Ignition wire Red Car fuse box Main fuse t Battery wire Yellow Ground wire Black To car chassis English 39 Installation non Japanese cars Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Phillips truss head sheet metal screw commercially available Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip A To attach this unit make sure the front of the control panel faces you and fit it into the mounting sleeve by pressing the four corners of the hard rubber frame at the same time Do not apply strong pressure to other sections than the corners otherwise troubles such as the impossibility of opening or closing the panel may result The hollow at the center of the rubber frame is designed to make it easier to remove discs If you
39. ing in the chart is the original setting Also the explanation for items that aren t applicable Manual Clock Adjustment etc are entered step by step English 31 Menu system In Standby mode Security Code Because authorization by the Security Code is required when it s removed from the vehicle personalizing this unit is by using the Security Code is a help in preventing theft When the Security Code function is activated the code can t be changed and the function can t be released Note the Security Code can be set as the 4 digit number of your choice 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Menu mode Press the MENU button for at least 1 second When MENU is displayed Security is displayed 3 Enter Security Code mode Press the kea or gt gt button for at least 1 second When ENTER is displayed CODE is displayed 4 Select the digits to enter Press the ka a or gt gt button 5 Select the Security Code numbers Press the FM or AM button 6 Repeat steps 4 and 5 and complete the Security Code 7 Confirm the Security Code Press the gt gt button for at least 3 seconds When RE ENTER is displayed CODE is displayed 8 Do the step 4 through 7 operation and reenter the Security Code APPROVED is displayed The Security Code function activates When the wrong Code is entered in steps 4 through 6 repeat from step 4 Press
40. ing mode during triangle indicator system adjustment such as audio control multi key system setup Display Setting W Blink ON The Triangle indicator blinks W Blink OFF The Triangle indicator does not blink Off Wait 0s Off Wait 3s Original setting Off Wait 25s In Standby mode Eject angle setting This function sets the opening and closing operation of a panel when a disc is inserted and when it is ejected Contrast Adjustment Display Setting Adjusting the display contrast BCT ANG SLP Opens and closes the panel while maintaining the angle of the control panel to the set angle Display and Setting BCT ANG LVL Opens and closes the panel after setting the Contrast 0 angle of the control panel to the horizontal position Contrast 5 Original setting Contrast 10 In Standby mode Panel action setting P Sets the panel movement when the panel action Dimmer Dimming this unit s display automatically when the vehicle light switch is turned ON back forward movement is set to its most end position Display Setting Display Setting PanelCNT 1 No angle can be adjusted if the panel position Dimmer ON The display dims has been set to its most end position Also if you Dimmer OFF The display doesn t dim have set the angle below the horizontal position the angle is set to horizontal when you set the panel to its most end pos
41. ition PanelCNT 2 The angle can be adjusted regardless of the panel position English 33 Menu system In Standby mode Switching preout Switching the preout between the rear and subwoofer In subwoofer it outputs without effect from the fader control Display Setting SWPRE Rear Rear preout SWPRE Sub W Subwoofer preout In Standby mode Built in Amp Mute Setting Toggles ON or OFF the mute control on the built in amplifier Turning ON this control enhances the preout quality Display Setting AMP Mute OFF The built in amplifier activates AMP Mute ON The built in amplifier deactivates In SIRIUS tuner source SIRIUS ID ESN display Displaying the SIRIUS ID Electronic Serial Number display Displa NECN POREN Serial amp SIRIUS ID ESN It is especially important to retain the unit serial number and the electronic SIRIUS Identification number for service activation and potential future service changes In FM reception CRSC Clean Reception System Circuit Temporarily have reception switched from stereo to mono to reduce multi path noise when listening to the FM station 34 English Display Setting CRSC ON The CRSC is ON CRSC OFF The CRSC is OFF Strong electrical fields such as from power lines may cause unstable sound quality when CRSC is turned ON In such a situation turn it OFF Text Scroll Setti
42. k Pops Pops Easy Easy 12 English Top 40 Top40 Jazz Jazz User memory The values set on the Audio Control page 12 Each setting value is changed with the Speaker Setting page 14 First select the speaker type with the Speaker setting Audio Control 1 Select the source for adjustment Press the SRC button 2 Select the key function section Press the NEXT button Repeatedly press the button until AUD is displayed above the 2 button Refer to Notes on Multi function Key System page 10 3 Enter Audio Control mode Press the 2 AUD button 4 Select the Adjustment item section Press the NEXT button Repeatedly press the button until the desired Adjustment item is displayed above the 2 5 button 1st section Adjustment Item Button Display Bass 2 BASS Middle B MID Treble 4 TRE Subwoofer 5 SW 2nd section Adjustment Item Button Display High Pass Filter 2 HPF Low Pass Filter 3 LPF Loudness 4 LOUD Balance amp Fader 5 BL F 3rd section Adjustment Item Button Display Volume offset 2 VOFF 5 Select the Audio Control item for adjustment Press the 2 5 button Each time the 2 5 button is pressed the adjustable audio items are switched among ranges of all stage section s tables on the following pages 6 Adjust the Audio Control item Press the kaa or g
43. mage the speakers Do no attempt to play a medium containing a non MP3 WMA file with the MP3 WMA extension The unit mistakes non MP3 WMA files for MP3 WMA data as long as they have the MP3 WMA extension Do not attempt to play a medium containing non MP3 WMA MP3 WMA playing order When selected for play Folder Search File Search or for Folder Select files and folders are accessed in the order in which they were written by the CD writer Because of this the order in which they are expected to be played may not match the order in which they are actually played You may be able to set the order in which MP3 WMA are to be played by writing them onto a medium such as a CD R with their file names beginning with play sequence numbers such as 01 to 99 depending on your CD writer For example a medium with the following folder file hierarchy is subject to Folder Search File Search or Folder Select as shown below Example of a medium s folder file hierarchy CQ ia Folder 2 File Root Od DD L__ ___ DO do G a d HO L___ t do Level 1 Level 3 Level 5 Level 2 Level 4 When a File Search is executed with file being played Operation of the button Current file S lt 4 Button Beginning of file b gt H pean 9 90 When a Folder Search is executed with file being played Operation of the button Current folder
44. n to 1 Select the key function section Press the NEXT button Repeatedly press the button until FSEL is displayed above the 5 button Refer to Notes on Multi function Key System page 10 2 Enter Folder Select mode Press the 5 FSEL button Select Mode is displayed During Select mode the folder information is displayed as shown below Folder name display Displays the current folder name n TT wm uh ERIT Hu E 3 Select the folder level Press the FM or AM button With the FM button you move 1 level down and with the AM button 1 level up Selecting a folder in the same level Press the kaa or gt gt button With the lt lt button you move to the previous folder and with the gt i button to the next folder Returning to the top level Press the 4 HOME button Scrolling the folder name display Press the SCRL button 4 Decide the folder to play Press the 2 OK button The Folder Select mode releases and the MP3 WMA in the folder being displayed is played The methods for moving to other folders in the folder select mode are different from those in the folder search mode See Notes on playing MP3 WMA page 8 for details Canceling the Folder Select mode Press the 3 EXIT button Text Title Scroll Scrolling the displayed CD text MP3 WMA text or MD title Press the SCRL button Function of disc changers with remote DNPP Disc Name
45. ng the displayed text scroll Display Setting Scroll Auto Repeats scroll Scroll MANU Scrolls when the display changes The text scrolled is shown below CD text Folder name File name Song title Artist name Album name MD title Text for the SIRIUS tuner source HD Radio source including Channel name etc Function of the KDC MPV8025 Built in Auxiliary input Setting Set the Built in Auxiliary Input function Display AUX OFF AUX ON Setting When selecting the source there s no Auxiliary Input When selecting the source there s Auxiliary Input In Standby mode CD Read Setting When there is a problem on playing a CD with special format this setting play the CD by force Display Setting CD READ 1 Play CD and MP3 WMA CD READ 2 Play CD by force Setting CD READ 2 cannot play MP3 WMA Some music CDs may not be played back even in the CD READ 2 mode Rotary volume operation select Various items can be set using the rotary volume knob Display Setting Rotary ON The rotary volume knob can be used for item setup Rotary OFF The rotary volume knob cannot be used for item setup To use the rotary volume knob for item setup select Rotary ON and press the 1 button in each setup mode In HD Radio mode Tuning Mode Sets the tuning mode Tuning mode Display Operation Auto seek Auto 1 Automatic search for a sta
46. nge V Offset 8 0 English 13 General features Rotary Volume knob operation mode select The rotary volume knob can be used for volume adjustment and various function setups Available setup functions The rotary volume knob can be used for the following setup Menu system Item selection Audio Control Adjustment of setup value Display control Display switching Station Disc Naming SNPS DNPS Character selection Folder select Folder search You can select the Rotary Volume Operation mode only when the 65 indicator is displayed above the 1 button during any function setup When the indicator is OFF you cannot use the rotary volume control for function setup and sound level adjustment To use the rotary volume knob 1 Turn the rotary volume operation ON See the Rotary volume operation select 35 page and select Rotary ON 2 Selecting the Rotary Volume Operation mode Press the 1 button When it s ON the 8 indicator blinks 3 Setting the function Rotate the Rotary Volume knob 4 Terminates the function setup using the rotary volume knob Press the 1 button Speaker Setting Fine tuning so that the System Q value is optimal when setting the speaker type 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Speaker Setting mode Press the Q button 14 English 3 Select the Speaker type Press the 2
47. nition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box AN If your car s ignition does not have an ACC position connect the ignition wires to a power source that can be turned on and off with the ignition key If you connect the ignition wire to a power source with a constant voltage supply as with battery wires the battery may die the console has a lid make sure to install the unit so that the faceplate will not hit the lid when closing and opening the fuse blows first make sure the wires aren t touching to cause a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car When only two speakers are being connected to the system connect the connectors either to both the front output terminals or to both the rear output terminals do not mix front and rear For example if you connect the connector of the left speaker to a front output terminal do not connect the connector to
48. nt off A Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a dry soft cloth Cleaning the CD Slot As dust tends to accumulate in the CD slot clean it every once in a while Your CDs can get scratched if you put them in a dusty CD slot Sa NOTE This Class B digital apparatus complies with Canadian ICES 003 6 English Sirius Satellite radio tuner Refer to the Sirius tuner control features of this manual for the operation method of Sirius Satellite radio tuner KTC SR901 SR902 optional accessory when connected About CDs Handling CDs Don t touch the recording surface of the CD CD R and CD RW are easier to damage than a normal music CD Use a CD R or a CD RW after reading the caution items on the package etc Don t stick tape etc on the CD Also don t use a CD with tape stuck on it When using a new CD If the CD center hole or outside rim has burrs use it after removing them with a ball pen etc A al CD accessories Don t use disc type accessories CD cleaning Clean from the center of the disc and move outward Nat Removing CDs When removing CDs from this unit pull them out horizontally CDs th
49. o a desired color 1 Select the key function section Press the NEXT button Repeatedly press the button until DISP is displayed above the 3 button Refer to Notes on Multi function Key System page 10 2 Enter display control mode Press the 3 DISP button 3 Quick call up the preset color Press the 4 CLR button Each time the button is pressed the Color mode switches as shown below Color mode Display he color changes in sequence COL Scan Preset color Silky White COL S White Preset color Red COL Red Preset color Blue COL Blue Preset color Blue Green COL B Green Original color COL User he color changes according COL SRC 0 the selected source he color changes every 6 hours COL Time The color continues to change gradually Hold down on the ka a or gt gt button COL User is displayed Release your finger at the color you want 4 Exit display control mode Press the 6 button Station Disc Naming SNPS DNPS Attaching a title to a Station or CD 1 Receive play the station disc you want to attach a title to A title can t be attached to an MD Refer to the Text Display Switching page 16 and select either DNPS or SNPS No name can be attached to the source if DNPS or SNPS cannot be selected for it 2 Enter name set mode Press the NAME S button for at least 2 seconds NAME SET is displayed 3 Move t
50. oofer preout The TEL mute function does not work VY The TEL mute wire is not connected properly t Connect the wire correctly referring to the section on Connecting Wires to Terminals The TEL mute function turns ON even though the TEL mute wire is not connected Y The TEL mute wire is touching a metal part of the car ts Pull the TEL mute wire away from the metal part of the car Even if Loudness is turned ON high pitched tone isn t compensated for WY Tuner source is selected ts High pitched tone isn t compensated for when in Tuner source Gand The sound quality is poor or distorted VY One of the speaker wires is being pinched by a screw in the car es Check the speaker wiring WV The speakers are not wired correctly ts Reconnect the speaker wires so that each output terminal is connected to a different speaker _ The Touch Sensor Tone doesn t sound WY The preout jack is being used ts The Touch Sensor Tone can t be output from he preout jack The Dimmer function doesn t work VY The Dimmer wire isn t connected correctly te Check the Dimmer wire connection _ The display color changes subtly VW This is because the temperature is different than the temperature when the setting was done ts The display color condition changes subtly according to the ambient temperature The panel is not hidden even when the power is turned off
51. rt WY There s already another disc inserted te Press the 4 button and remove the disc Direct Search can t be done Y Another function is ON ts Turn Random Play or other functions OFF 44 English HD Radio source No sound can be heard or the volume is low Y The preset broadcast station is not transmitting in the mode that was set with Receive mode Setting page 35 ts Please set Receive mode Setting to Auto Y In digital AM broadcasting receive mode switches between stereo and monaural too often ts Receiving condition is bad or unstable Stereo is chosen when receiving condition is good and it switches to monaural when the condition becomes bad Y HD Radio tuner is connected to KCA S210A or other units ts Connect the HD Radio tuner directly to the control unit If the following situations consult your nearest service center Even though the disc changer is connected the Disc Changer source is not ON with AUX EXT showing in the display during the Changer Mode The messages shown below display your systems condition EJECT No Disc TOC Error EUS Blank Disc No Track E 15 No Panel E 77 Mecha Error Hold Error o disc magazine has been loaded in he changer The disc magazine is not completely loaded Load the disc magazine properly o CD in the unit Insert the CD o disc has been loaded in the disc magazine Load a di
52. sc into the disc magazine o disc has been loaded in the disc magazine Load a disc into the disc magazine The CD is quite dirty The CD is upside down The CD is scratched a lot Clean the CD and load it correctly The CD is upside down Load the CD correctly othing has been recorded on the MD o tracks are recorded on the MD although it has a title Media was played that doesn t have data recorded that the unit can play Use media that has data recorded that the unit can play The faceplate of the slave unit being connected to this unit has been removed Replace it The unit is malfunctioning for some reason Press the reset button on the unit If the E 77 code does not disappear consult your nearest service center Something is wrong with the disc magazine Or the unit is malfunctioning for some reason gt Check the disc magazine And then press the reset button on the unit If the Mecha Error code does not disappear consult your nearest service center The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60 C 140 F stopping all operation Cool down the unit by opening the windows or turning on the air conditioner As the temperature falls below 60 C 140 F the disc will start playing again NO NAME Waiting Load Reading NO ACCESS IN Blink Attempted to display DNPS during
53. se harmful o radio or television reception which can be determined by turning the equipment off and on the u ser is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receive r Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help English 3 Safety precautions AWARNING To prevent injury or fire take the following precautions Insert the unit all the way in until it is fully locked in place Otherwise it may fall out of place when jolted When extending the ignition battery or ground wires make sure to use automotive grade wires or other wires with a 0 75mm AWG18 or more to prevent wire deterioration and damage to the wire coating To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit If the unit starts to emit smoke or strange smells turn off the power immediately and consult your Kenwood dealer Make sure not to get your fingers caught between he faceplate and the unit Be careful not to drop the unit or subject it to rong shock The unit may break or crack because it contains glass parts Do not touch the liquid crystal fluid if the LCD is
54. t gt button Each time the button is pressed the setting switches as shown below The Adjustment item can also be controlled by the rotary volume knob Refer to Rotary Volume knob operation mode select page 14 7 Exit Audio Control mode Press the 6 button The loudness setting can also be adjusted by pressing the 4 button This mode is available only when Subwoofer Output page 14 is ON 1st section 2 button Adjustment Item Display Range Bass level Bass 8 8 3 button Adjustment Item Display Range Middle level Middle 8 8 4 button Adjustment Item Display Range Treble level Treble 8 8 5 button Adjustment Item Display Range Subwoofer level SW Level 15 15 2nd section 2 button Adjustment Item Display Range Front Rear High Pass Filter HPF THRU 100 125 170 Hz 3 button Adjustment Item Display Range Subwoofer Low Pass Filter LPFSW _50 80 120 THRU Hz 4 button Adjustment Item Display Range Loudness LOUD ON OFF 5 button Adjustment Item Display Range Balance Balance L 15 R15 Fader Fader R15 F 15 When the Dual Zone System is ON the setting for the High Pass Filter is nullified 3rd section 2 button Adjustment Item Volume offset Volume offset Each source s volume can be set as a difference from the basic volume Display Ra
55. t least 1 second MENU is displayed 3 Select the Auto Memory Entry mode Press the FM or AM button Select the Auto Memory display 4 Open Auto Memory Entry Press the ka a or gt gt button for at least 2 seconds When 6 stations that can be received are put in the memory Auto Memory Entry closes 5 Exit Menu mode Press the MENU button The receiving method can be switched with the setting of Receive mode Setting page 35 30 English Menu system MENU Menu System Setting during operation beep sound etc functions The Menu system basic operation method is explained here The reference for the Menu items and their setting content is after this operation explanation 1 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 2 Select the menu item Press the FM or AM button Example When you want to set the beep sound select the Beep display 3 Set the menu item Press the kaa or gt gt button Example When Beep is selected each time the button is pressed it switches Beep ON or Beep OFF Select 1 of them as the setting You can continue by returning to step 2 and setting other items 4 Exit Menu mode Press the MENU button When other items that are applicable to the basic operation method above are displayed afterwards their setting content chart is entered Normally the uppermost sett
56. tellite Radio Mode Switching Seek Mode Select the channel Channel Search Direct Access Tuning Selecting the Preset Band Channel Preset Memory Preset Tuning Channel Scan Text Scroll for SIRIUS tuner source HD Radio control features 29 Tuning Auto Memory Entry Menu system 31 Tuning Mode Tuning Direct Access Tuning Station Preset Memory Auto Memory Entry Preset Tuning CD MP3 WMA External disc control features 22 enu System Security Code Touch Sensor Tone anual Clock Adjustment DSI Disabled System Indicator Selectable Illumination Triangle indicator setting Contrast Adjustment Dimmer OFF Wait Time Setting ject angle setting anel action setting witching preout uilt in Amp Mute Setting RIUS ID ESN display RSC Clean Reception System Circuit Text Scroll Built in Auxiliary input Setting CD Read Setting Rotary volume operation select Um Za AND Playing CD amp MP3 WMA Playing External Disc Fast Forwarding and Reversing Track File Search Disc Search Folder Search Direct Track File Search Direct Disc Search Track File Disc Folder Repeat Scan Play 2 English Tuning Mode Receive mode Setting Auto Memory Entry Basic Operations of remote 36 Accessories Installation Procedure 38 Connecting Wires to Terminals 39 Installation 40 Removing the Unit 42 Troubleshooting Guide 43 Specifications 46 AWarni ng
57. the CD play having no disc names preset Attempted to display the ID3 tag while the MP3 WMA having no ID3 tag is being played Radio text data is being received Discs are being exchanged in the Disc changer The unit is reading the data on the disc After setting it in the Disc Changer DNPP was done without having it been played at least 1 time The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center Unsupported File Protected File Demo Mode A MP3 WMa is played with a format that this unit can t support en A copy protected file is played D The Demonstration mode has been selected Hold down button 5 and press the Reset button to release the Demonstration mode English 45 Specifications Specifications subject to change without notice FM tuner section Frequency range 200 kHz space 87 9 MHz 107 9 MHz Usable sensitivity S N 30dB 9 30 Bf 0 8 uV 75 QO Quieting Sensitivity S N 50dB 15 20 Bf 1 6 uV 75 Q Frequency response 3 dB 30 Hz 15 kHz Signal to Noise ratio MONO 70 dB Selectivity 400 kHz gt 80 dB Stereo separation 1 kHz 40 dB AM tuner section Frequency range 10 kHz space 530 kHz 1700 kHz Usable sensitivity S N
58. the Preset Band Press the FM button Each time the button is pressed the preset band switches between the SR1 SR2 SR3 and SR4 Channel Preset Memory Putting the channel in the memory 1 Select the preset band Press the FM button 2 Select the channel to put in the memory Press the kaa or gt gt button 3 Select the key function section Press the NEXT button Repeatedly press the button until the function item is not displayed above the 2 5 button Refer to Notes on Multi function Key System page 10 4 Put the channel in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 channel can be put in the memory on each 1 6 button Only the channel number is stored Category information is not stored Preset Tuning Calling up the channels in the memory 1 Select the preset band Press the FM button 2 Select the key function section Press the NEXT button Repeatedly press the button until the function item is not displayed above the 2 5 button Refer to Notes on Multi function Key System page 10 3 Call up the channel Press the desired 1 6 button English 27 SIRIUS tuner control features Channel Scan Every receivable Channel is checked for 10 seconds 1 Start Channel Scan Press the AUTO button for at least 1 second The channel number display blinks 2 Rel
59. tion Preset station seek Auto 2 Search in order of the stations in the Preset memory Manual Manual Normal manual tuning control In HD Radio mode Receive mode Setting Sets the receive mode 1 Select the Receive mode Press the FM or AM button Select the Receive Mode display 2 Enter Receive mode Press the kaa or gt gt button for at least 1 second 3 Set the Receive mode Press the FM or AM button Each time the button is pressed the Receive mode switches as shown below Receive mode Display Auto mode Auto Operation Analog broadcasts and digital broadcasts will be switched automatically When both are being transmitted the digital broadcast will have priority Digital broadcasts only Analog broadcasts only Digital Digital Analog Analog 4 Exit Receive mode Press the MENU button Even if the Auto setting an analog broadcast will be received during the reception of a ball game mode non delayed broadcast program In HD Radio mode Auto Memory Entry For the operation method refer to Auto Memory Entry page 30 English 35 Basic Operations of remote VOL ATT l Pil FM AM DISC DISC lt gt DNPP l EE oa Not Used C_ 5 DIRECT OK 01 19 ail beeen KENWOOD Loading and Replacing the battery Basic operations Use two AA size batteries VOL buttons

Kenwood KDC-MPV8025 Car Stereo System User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents