Kenwood KDC-MP146 Car Stereo System User Manual
Contents
1. To assure good reception note the following Communicate with the cell phone within he line of sight distance of 10 m 30 ft The communication range becomes shorter depending on the surrounding environment The communication range also becomes shorter when there is an obstacle between this unit and the cell phone The above maximum communication range 10 m is not always assured A broadcast station or walkie talkie located nearby can interfere with communication due to a too strong signal Installation accessories Dn M KDC U7056DAB only English 11 Connecting wires to terminals Fuse 10A FM AM antenna input O Digital radio antenna Accessory P t KDC U7056DAB only Microphone Accessory 5 KDC U7056BT KDC U7056BTL only White To front left speaker White Black Gray To front right speaker A Gray Black Green Wiring harness Ey Accessory To rear left speaker A Green Black Purple To rear right speaker A Purple Black Speaker Impedance 4 8 Q Ignition key switch Red Ignition wire Car fuse box Yellow Battery wire Main fuse lt Battery KDC U7056DAB only 12 Quick Start Guide USB connector 0 8m ai To USB device USB maximum power supply current DC5V 1A at Micro2. USB Pandora TI REAR andora of device connected via Pandora aha of iPod connected to front USB aha FRONT erminal aha of iPod connected to rear USB aha REAR erminal aha of device connected via aha uetooth 6 Quick Start Guide Auxiliary input Bluetooth audio BT AUDIO co p Auxiliary Input AUX I This source can be selected only when it can be played 21 Function of KDC U7056DAB BI Function of KDC U7056BT Volume Turn Control knob to adjust the sound volume USB terminal A USB device or iPod can be connected The CA U1EX Max 500mA or KCA iP 102 optional accessories is recommended to connect a USB device or iPod Auxiliary input A portable audio device can be connected with a stereo mini plug 3 5 mm g Playing music CD USB iPod Qs KENWOOD A S Playing a disc Open the Disc slot cover upward Insert a disc in the Disc slot When it is inserted the source is switched automatically and playback starts Close the Disc slot cover Playing a USB device iPod Connect a USB device or iPod to the USB terminal as shown above When it is connected the source is switched automatically and playback starts You can connect the iPod or USB device to eithe
3. mode according to how the speakers are connected Refer to lt 2 Way 3 Way Crossover Setting gt next page ED For how to connect speaker wires If you select a wrong mode to terminals other than speaker terminals and Preout terminals refer The speakers can break to lt Connecting wires to terminals gt The output sound level may be page 12 extremely low 14 Quick Start Guide 2 Way 3 Way Crossover Setting Select a crossover mode 2 way or 3 way according to how the speakers are connected 1 2 Press the SRC to select STANDBY Pressing down the Y and l lt lt 4 s for at least 3 seconds allows you to enter the 2 way 3 way crossover setting mode The currently selected crossover mode is displayed To change it turn Control knob to select YES and then press Control knob A confirmation screen appears If you are sure you want to change the crossover mode turn the Control knob to select YES and then press the Control knob The newly selected crossover mode is displayed canceling the 2 way 3 way crossover setting mode English 15 Installing Removing the unit Non Japanese cars Bend the tabs of the mounting sleeve with a screwdriver or the like and attach it in place Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip Japanese cars 1 Remove the trim plate wit
4. part Specifications FM tuner section Frequency range 200 kHz step 87 9 MHz 107 9 MHz 50 kHz step 87 5 MHz 108 0 MHz Usable sensitivity S N 26dB 7 2081 0 63 uV 75 O Quieting Sensitivity S N 46dB 15 2086 1 6 uV 75 O Frequency response 3 dB 30 Hz 15 kHz Signal to Noise ratio MONO 75 dB Stereo separation 1 kHz 45 dB AM tuner section Frequency range 10 kHz step 530 kHz 1700 kHz 9 kHz step 531 kHz 1611 kHz Usable sensitivity S N 20dB 31 36 uV DAB tuner section KDC U7056DAB Frequency range L BAND 1452 960 MHz 1490 624 MHz BAND III 174 928 MHz 239 200 MHz Sensitivity 100 dBm Signal to Noise ratio 80 dB Antenna Connector type SMB Antenna Output Voltage 11 16V 14 4 V Antenna Maximun Current lt 100 mA CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 24 Bit Spindle speed Audio files 500 200 rpm CLV Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 008 Signal to Noise ratio 1 kHz 110 dB Dynamic range 93 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files USB interface USB Standard USB1 1 2 0 Full speed File System FAT12 16 32 Maximum Supply current DC 5V 1 A Decode MP3
5. unit for the first time When this unit is first turned on the interactive menu appears for setting the interface language and demonstration mode This menu disappears when no action is taken for 15 seconds 1 KDC U7056BTL only Select the interface language to display the menu items of the Function setting from English Arabic and Persian Turn Control knob to select the language and then press Control knob 2 KDC U7056BTL only If you selected English in step 1 select the language to display the audio file information from English and Thai Arabic or Persian is automatically selected if you selected Persian or Arabic in step 1 3 Press Control knob when the message To cancel DEMO Press the volume knob appears 4 Turn Control knob to select YES and then press Control knob The interface language and demonstration mode can also be set with the Function setting Refer to lt 12 4 Demonstration mode setting gt in Instruction manual Control knob Volume knob KENWOOD Q 45 Release Adjusting the clock 1 Press Control knob to enter the Function setting mode The item can be selected and determined as follows Settings Clock amp Date Clock Adjust Turn Control knob to select the item and press Control knob 2 Turn Control knob to adjust the hour and then pr
6. 70 mm D Accessory Accessory When installing the antenna on the right side 57 Front pillar Earth sheet Accessory 7 Accessory 6 Where the earth sheet of amplifier unit Accessory can be pasted on the metal part of the front pillar Antenna Installation 1 Check the installation location 2 Clean the area where antenna film Accessory amplifier unit Accessory and earth sheet are pasted with the included cleaner Accessory The coating on the metal surface need not be removed Wait until the glass surface is completely dry before pasting If the glass surface is cold such as during winter warm it with defroster or dryer 3 Remove the separator tag of antenna film horizontally and paste the antenna on the front glass Remove the separator gently Do not touch the pasting surface adhesive side of the antenna film 4 Remove the separator tag II of antenna film vertically and paste the antenna gently while applying pressure 5 After pasting rub the element in the glass surface in the direction of the arrow shown in the figure to bond it 6 Remove the application film tag III Do not touch the feeder terminal of the element Also do not apply any glass cleaner Feeder terminal 7 Match the protrusion of the amplifier with the A on the antenna film and paste Do not touch the feeder terminal or the pasting surface adhes
7. KENWOOD KDC U7056DAB KDC U7056BT KDC U7056BTL CD RECEIVER Quick Start Guide JVCKENWOOD Corporatio aha 0 Bluetooth mn dio B DiPod iPhone US 2012 JVC KENWOOD Corporation B59 2188 10 01 M Contents About the Quick Start Guide Before use Appendix 1 121 1 4 General Operations Playing music CD USB iPod 5 Listening to the radio Digital radio 8 Hands free phoning Before installation Connecting wires to terminals 12 3 way speaker system setup Installing Removing the unit Installing the Microphone unit 5 Installing the Digital radio antenna 17 SPECIFICATIONS saranan 21 About the Quick Start Guide This Quick Start Guide describes basic functions of this unit For functions not described in this Guide refer to the Instruction Manual on the following website manual kenwood com edition im362 To refer to the Instruction Manual a browser such as Internet Explorer 7 or later Firefox 3 6 or later Chrome 20 or later Safari 5 1 or later iOS Safari 4 0 or later or Android 2 2 or later is required 2 Quick Start Guide Before use A WARNING To prevent injuries or a fire take the following precautions Stop the car before operating the unit To prevent a short circuit never put or leave any metallic objects such as coins or met
8. L Pairing a Bluetooth device You can pairing your Bluetooth device in this unit 1 Operate the Bluetooth device to request this unit for connection The name of this unit KDC HH appears on the Bluetooth device Press the volume knob appears 2 Press Control knob Connection to your Bluetooth device starts Pairing Success appears a while later and then the previous source is selected When registration of your cell phone is completed the phone book of the cell phone is automatically downloaded to this unit If the phone book has not been downloaded to this unit operate the cell phone to download it Dialing a number in the phone book Dial the phone number in the phone book of your cell phone If the phone book has not been downloaded to this unit operate the cell phone to download it 1 Press LO 2 Turn Control knob to select Phone Book and then press Control knob 3 Turn Control knob to select a name and then press Control knob 4 Turn Control knob to select a phone number 5 Press LO Answering a phone call Press 6 Disconnecting a call Press 6 English 9 Before installation WARNING The unit can only be installed in a car with a 12V DC power supply negative ground If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fir
9. WMA AAC WAV Audio section Maximum output power 50 W x 4 Full Bandwidth Power at less than 1 THD 2Wx4 Preout level Load CD KDC U7056DAB 2500 mV 10 kQ KDC U7056BT KDC U7056BTL 4000 mV 10 kQ Preout impedance lt 600 Q Speaker Impedance 4 80 Tone Bandi 62 5 Hz 9 dB Band3 160 Hz 9 dB Band5 400 Hz 9 dB Band 1 kHz 9 dB Band2 100 Hz 9 dB Bandi 250 Hz 9 dB Band6 630 Hz 9 dB 83608 1 6 kHz 9 dB Band9 2 5 kHz 9 dB Band10 4 kHz 9 dB Band11 6 3 kHz 9 dB Band12 10 kHz 9 dB Band13 16 kHz 9 dB Bluetooth section Version Bluetooth Ver 2 1 EDR Certified Frequency range 2 402 2 480 GHz Output Power 4dBm MAX OdBm AVE Power Class 2 Maximum Communication range Line of sight approx 10m Profiles HFP Hands Free Profile SPP Serial Port Profile PBAP Phonebook Access Profile OPP Object Push Profile A2DP Advanced Audio Distribution Profile AVRCP Audio Video Remote Control Profile Auxiliary input Frequency response 3 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input Impedance 10 kQ General Operating voltage 14 4 V 10 5 16V allowable Maximum Current consumption 10 A Installation Size W x H x D 182 x 53 x 159 mm Weight 1 3 kg Specifications subject to change without notice English 21 Requirements Pandora Requirements for listening to the Pandora are as foll
10. al tools inside the unit CAUTION Adjust the volume so that you can hear sound outside the car Driving with the volume adjusted to a too high level may cause an accident Wipe off the dirt on the panel with a dry silicon or soft cloth Failure to observe this precaution may result in damage to the monitor or unit Cleaning the connector The unit may not function properly if the connector between the unit and faceplate are dirty Detach the faceplate and clean the connector with a cotton swab gently being careful not to damage the connector KENWOOD Condensation When the car is air conditioned moisture may collect on the laser lens This may cause disc read errors In this case remove the disc and wait for the moisture to evaporate Notes If you experience problems during installation consult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they can work with your model and in your area Characters that conform to ISO 8859 1 can be displayed To display characters in the following language additional setting is required Chinese Refer to Chinese of lt 12 5 Initial settings gt Arabic Persian Thai Refer to TAG Language of lt 12 5 Initial settings gt About the discs used with this unit This unit can only play the CDs with The erae dis cannot be used A disc th
11. at is not round disc with coloring on the recording surface or a disc that is dirty A recordable rewritable disc that has not been finalized For the finalization process refer to the instruction manual that came with your disc writing software or your disc recorder An 8 cm 3 inch disc An attempt to insert using an adapter can cause malfunction ab Handling discs Do not touch the recording surface of the disc Do not stick tape etc on the disc or use a disc with tape stuck on it Do not use any accessories for the disc Do not use any solvents to clean discs Use a dry silicon or soft cloth Clean the disc by moving the cloth outward from the center of the disc When removing a disc from this unit pull it out horizontally If the center hole or outside rim of a disc has burrs remove them before inserting a disc How to reset your unit If the unit fails to operate properly press the Reset button The unit returns to the factory settings Reset button The illustrations of the display and panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the images on the display may be inapplicable CAUTION Keep battery out of reach of children and in original package until ready to u
12. e Always connect those wires to the power source running through the fuse box CAUTION Use the power harness enclosed with this unit for connecting power Using a power harness enclosed with other models can cause malfunction Install this unit in the console of your vehicle Do not touch the metal parts of this unit during and shortly after use of the unit Metal parts such as the heat sink and enclosure become hot Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work o professionals f you experience any problem during installation consult your Kenwood dealer Disconnect the battery s negative terminal before installing the unit nsulate unconnected wires with vinyl ape or other similar materials To prevent a short circuit do not remove the caps on the ends of the unconnected wires and terminals Be sure to ground this unit to the car s chassis again after mounting f the fuse blows first make sure the wires are not touching other parts to cause a short circuit and then replace the old fuse with one with a new the same rating When connecting only two speakers connect the connectors either to both of the front output terminals or to both of the rear output terminals do not mix front and rear terminals For example if 10 Quick Start Guide you connect the connector of the left speaker to a front output t
13. e is no danger of hazardous radiation outside the unit TRA REGISTERED No ER0106384 13 DEALER No 0016026 08 he Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by JVC KENWOOD Corporation is under license Other trademarks and trade names are those of their respective owners he AAC logo is a trademark of Dolby Laboratories Made for iPod and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod or iPhone respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod or iPhone may affect wireless performance i ti hone iPod iPod classic iPod nano and iPod ouch are trademarks of Apple Inc registered in the U S and other countries iTunes and Safari are trademark of Apple Inc IOS is a trademark or registered trademark of Cisco in the U S and other countries and is used under license Adobe Acrobat and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Android and Chrome are trademark of Google Inc BlackBerry RIM Research In Motion and related trademarks names and logos are the property of Research In Motion Limited and a
14. erminal do not connect the connector to a rear output terminal Connect the speaker wires correctly to the corresponding terminals The unit may be damaged or fail to work if you share he wires or ground them to any metal part in the car Do not use your own screws Use only he supplied screws Using wrong screws could damage the unit f your car s ignition key switch does not have an ACC position connect the ignition wires to a power source that can be turned on and off with the ignition ey If you connect the ignition wires to a constant voltage power source as with battery wires the battery may die f the console has a lid make sure to install the unit so that the faceplate will not hit the lid when it is closed or opened After the installing the unit check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less Reception may become poor if there are metal objects near the Bluetooth antenna Bluetooth antenna unit KDC U7056DAB This unit has the cooling fan to decrease he internal temperature Do not mount he unit in a place where the cooling an of the unit are blocked Blocking hese openings will inhibit the cooling of the internal temperature and result in malfunction Cooling fan For Good Reception
15. ess Control knob 3 Turn Control knob to adjust the minute and then press Control knob 4 Press and hold Q 45 to exits the Function setting mode Remove the faceplate at once after pressing the Release button otherwise it can fall down due to vibration The faceplate is a precision component of he unit and can be damaged by shocks or jolts eep the faceplate in its case while detached Do not place the faceplate and case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with oo much dust or the possibility of water splashing English 5 General operations SRC Control knob Volume knob USB terminal Power To turn the power ON press SRC To turn the power OFF press and hold SRC Source selection Pressing SRC repeatedly switches among sources Source Display Standby STANDBY igital radio DIGITAL RADIO uner TUNER SB device connected to front USB USB FRONT erminal SB device connected to rear USB USB REAR erminal iPod connected to front USB terminal iPod FRONT iPod connected to rear USB terminal iPod REAR andora of iPod connected to front Pandora SB terminal e FRONT andora of iPod connected to rear
16. h reference to lt Removing the trim plate gt 2 Align the holes in the unit two locations on each side with the vehicle mounting bracket and secure the unit with the accessory screws i Ej 199 N m mB Je L 0 o5mm ka 16 Quick Start Guide Removing the trim plate Engage the catch pins on the extraction key Accessory and release the two locks on the upper part of frame Lift up and pull the frame forward as shown in the figure 0 Lock Catch LA Accessory 2 2 When the upper part of frame is removed remove the lower part of frame amp The frame can be removed from the bottom side in the same manner Removing the unit T Remove the trim plate with reference to lt Removing the trim plate gt 2 Remove the faceplate 3 Insert the two extraction keys Accessory deeply into the slots on both sides as shown 4 Lower the extraction key toward the bottom and then pull out the unit halfway while pressing the extraction key owards the inside Accessory 2 Be careful to avoid injury from the catch pins on the extraction key 5 Pull the unit all the way out with your hands being careful not to drop it Installing the Microphone unit d Check the installation position of the microphone Accessory Clean the installation surface Install the microphone Lay the cable up to the unit with it secured at several pos
17. he included cleaner Accessory Do not bend or damage the film antenna Accessory Warm the pasting surface by turning on the heater for example before applying It may not be possible to install on some type of vehicle Check the cable routing of the film antenna Accessory and amplifier Accessory before pasting e g door front English 17 KDC U7056DAB only Installing the Digital radio antenna Installation overview Ed The antenna should be installed on the passenger side for safety Use cord clamper Accessory 8 to secure the antenna to the pillar at several ocations The direction of the antenna film Accessory 6 changes depending on whether the film antenna is installed on he right side or left side Separate the antenna film Accessory Separate from other antennas by a Dono rom the ceramic line black part at the op of the front glass by 150 mm Also place it about 70 mm inside the ceramic line at the side end of the front glass where the earth sheet of the amplifier can be pasted on the metal part of the front pillar least 100 mm paste the amplifier Accessory on the ceramic line black part around the front glass Because there is no enough adhesion 18 Quick Start Guide Determining the antenna installation location When installing the antenna on the left side Front pillar Earth sheet
18. ion gt page 6 Selecting a band FM or AM Tuner only ress A Selecting a station service ress laal or gt I The seek mode can be changed Refer to lt 9 5 Tuner setting gt or lt 10 1 Listening 0 the Digital Radio gt in Instruction manual Station preset memory 1 2 8 ress A to select a band Tuner only ress laal or gt gt to select the station service you want to save in the station preset memory TUNER Press Q 45 DIGITAL RADIO Press Q 45 twice Press Q 45 again to enter the Mix Station preset mode In this mode different bands and tuner sources FM AM Digital Radio etc can be saved in the same preset layer which allows you to recall a desired station without switching between bands and or tuner sources Maximum of 6 stations can be preset in the Mix Station preset mode Quick Start Guide 4 Turn Control knob to select preset number FM Digital Radio 1 18 AM 1 6 and then press and hold Control knob Recalling the stations in the memory 1 Press A to select a band Tuner only 2 Press Q 45 3 Turn Control knob to select a preset number FM Digital Radio 1 18 AM 7 6 and then press Control knob n the Mix Station preset mode band names of tuner sources are displayed as ollows FM FM broadcast station AM AM broadcast station DR Digital Radio service Hands free phoning Control knob
19. itions using tape or the like Install the microphone as far as possible from the cell phone RUN X Accessory 5 Fix the cable with a commercial item of tape Remove the separator of the microphone and stick the microphone to the place shown above Adjust the direction of the microphone to the driver KDC U7056DAB only Installing the Digital radio antenna CAUTION This film antenna is exclusively for use inside the vehicle Do not install at the following locations Where it may block driver s view Where it may obstruct operation of safety devices such as air bags On movable glass surface such as rear hatch Signal strength will decrease at the following locations On IR reflecting glass or where covered with mirror type glass film Where it overlaps with genuine radio antenna pattern Where it overlaps with window heating wires At side of vehicle quarter window On rear window When glass that blocks radio signals eg IR reflecting glass thermal insulation glass is used Reception may decrease due to noise when windshield wiper air conditioner or motor is turned on Reception may decrease depending on the direction of the broadcast station with respect to the vehicle antenna Be sure to check the installation location of film antenna Accessory before installing Film antenna cannot be re pasted Thoroughly wipe oil and dirt from the pasting surface with t
20. ive side of the amplifier When installing the antenna on the right side Match the protrusion with amp Earth sheet me Accessory Accessory 7 English 19 KDC U7056DAB only Installing the Digital radio antenna When installing the antenna on the left side Accessory 7 Accessory 6 es Earth sheet Match the protrusion with amp 8 Remove the film covering the earth sheet and paste the earth sheet on the metal part of the vehicle Provide sufficient leeway for the earth sheet so that it does not interfere with the interior parts front pillar cover Also take care that the interior parts do not interfere with the amplifier Front glass Accessory 7 J Front pillar Interior part Earth sheet 9 Wire the antenna cables Use cord clamper Accessory to secure the antenna to the pillar at several locations 20 Quick Start Guide Take the following precautions when passing the antenna cable inside the front pillar where the air bag is installed Install the amplifier part of the antenna cable in front or above the air bag so that the antenna and the air bag do not interfere Front pillar The front pillar cover is secured with a special clip which may need to be replaced when the front pillar cover is removed Contact your vehicle dealer for details on replacing the front pillar cover and availability of replacement parts Interior
21. ng to the Aha are as follows iPhone or iPod touch Use an Apple iPhone or iPod touch running iOS4 or later Search for aha in the Apple iTunes App Store to find and install the most current version of the Aha application on your device iPhone iPod touch connected to this unit with a KCA iP102 Android Use Android OS 2 2 or later Download the Aha application to your smartphone from the Google Play Bluetooth must be built in and the following profiles must be supported SPP Serial Port Profile A2DP Advanced Audio Distribution Profile NOTE In the application on your device log in and create a free account with Aha Internet connection by LTE LTE 3G EDGE or WiFi Because Aha is a third party service the specifications are subject to change without prior notice Accordingly compatibility may be impaired or some or all of the services may become unavailable Some Aha functionality cannot be operated from this unit aha the Aha logo and the Aha trade dress are trademarks or registered trademarks of HARMAN International Industries used with permission The marking of products using lasers Except for some areas CLASS 1 LASER PRODUCT The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class Ther
22. ows iPhone or iPod touch Use an Apple iPhone or iPod touch running under iOS3 or later Search for Pandora in the Apple iTunes App Store to find and install the most current version of the Pandora application on your device iPhone iPod touch connected to this unit with a KCA iP102 Android or BlackBerry Download the Pandora application to your smartphone from Pandora site using it s standard browser Bluetooth must be built in and the ollowing profiles must be supported SPP Serial Port Profile A2DP Advanced Audio Distribution rofile NOTE In the application on your device log in and create an account with Pandora If you are not already a registered user an account can also be created at www pandora com Internet connection by LTE LTE 3G EDGE or WiFi Pandora is available only in the U S Canada Australia and New Zealand Because Pandora is a third party service the specifications are subject to change without prior notice Accordingly compatibility may be impaired or some or all of the services may become unavailable Some functions of Pandora cannot be operated from this unit For issues using the application please contact Pandora at pandora support pandora com PANDORA the PANDORA logo and the Pandora trade dress are trademarks or registered trademarks of Pandora Media Inc used with permission Requirements Aha Requirements for listeni
23. phone Accessory KDC U7056DAB only If no connections are made do not let the wire come out from the tab Blue White Power control wire When using the optional power amplifier connect his wire to its power control terminal Depending on what antenna you are using connect either to the control terminal of the motor antenna or to the power terminal for the booster amplifier of the film type or short pole type antenna Max 300mA 12V Blue Antenna control wire ANT CONT Brown Mute control wire When connecting to the Kenwood navigation MUTE system Refer to your navigation manual Orange White Dimmer control wire ILLUMI To car light control switch Light Blue Yellow Steering remote control wire To use the steering wheel remote control feature an exclusive remote adapter not supplied that REMOTECONT matches your car is required 1 STEERING WHEEL AREMOTE INPUT English 13 3 Way speaker system setup Connect the speaker wires White Black Gray Gray Black To MID Range left speaker To MID Range right speaker Green Black Purple Purple Black To left Tweeter To right Tweeter Blue White Power control wire When using the optional power amplifier connect this wire to its power control terminal If no connections are made do not let the wire come out from the tab A Select a crossover
24. r one of the USB terminals provided at the front and rear of this unit f you connect it to the rear USB terminal he REAR USB indicator stays lit 11 optional accessories lt gt A V i Selecting an audio file folder ress A or V Selecting a song track or file ress laal or gt gt Fast forwarding or fast backwarding a song track or file ress and hold ka a or gt REAR USB indicator USB Terminal Pause and play a song track or file Press and hold Q 5 Music search You can search for the song you want to play 1 Press Q 45 2 Search for a song Operation type Operation Selecting items Turn Control knob Determining selection Press Control knob Returning to previous item Press Q 5 To cancel music search in audio files or iPod Press and hold Q 45 Ejecting disc Open the Disc slot cover upward and press 4 Removing USB device iPod Switch to a source other than USB iPod Pandora and Aha Radio and then remove the USB device Data contained in the USB device iPod may be damaged if you remove it when it is used as the active source English 7 Listening to the radio Digital radio SRC Control knob A A S aael Selecting a tuner source Press SRC to select TUNER or DIGITAL RADIO KDC U7056DAB only Refer to lt Source select
25. re registered and or used in the U S and countries around the world Used under icense from Research In Motion Limited nternet Explorer and Windows Media are registered trademark of Microsoft Corporation in the United States and other countries Firefox is a registered trademark of Mozilla Foundation in the United States and other countries ANDORA the PANDORA logo and the andora trade dress are trademarks or registered trademarks of Pandora Media Inc used with permission aha the Aha logo and the Aha trade dress are trademarks or registered trademarks of HARMAN International Industries used with permission KENWOOD
26. se Dispose of used batteries promptly If swallowed contact a physician immediately Do not leave the battery near fire or under direct sunlight A fire explosion or excessive heat generation may result Do not set the remote control in hot places such as on the dashboard The Lithium battery is in danger of explosion if replaced incorrectly Replace it only with the same or equivalent type English 3 Appendix A bout Audio file Playable Audio files AAC LC m4a MP3 mp3 WMA wma WAV wav of USB device Playable disc media CD R RW ROM Playable disc file formats 5 ayable USB devices USB mass storage class Playable USB device file systems FAT12 FAT16 FAT32 The online manual about audio files is put on the site W ww kenwood com cs ce audiofile Models of iPods iPhones that can be connected to this unit M ade for iPod touch Pod touch 00 touch 00 touch Pod classic od with video od nano 6th generation Pod nano 5th generation od nano 4th generation od nano 3rd generation Pod nano 2nd generation od nano 1st generation hone 4S Phone 4 hone 3GS hone 3G Phone 4th generation 3rd generation 2nd generation 1st generation For information on the compatibility with iPod iPhone software visit www kenwood com cs ce ipod 4 Quick Start Guide O 9660 Level 1 2 Joliet Long file name Preparations Before using this
Download Pdf Manuals
Related Search