Kenwood DNX7020EX GPS Receiver User Manual
Contents
1. gt a s D 03042tex TO CHECK BRAKE lf tractor requires more than five 5 feet to stop at highest speed in highest gear on a level dry concrete or paved surface then brake must be serviced You may also check brake by e Park tractor on a level dry concrete or paved surface depress brake pedal all the way down and engage parking brake e Place gear shift lever in neutral N position The rear wheels must lock and skid when you try to manu ally push the tractor forward If the rear wheels rotate then the brake needs to be serviced Contact a qualified service center TO REPLACE MOTION DRIVE BELT See Fig 27 Park the tractor on level surface Engage parking brake For assistance there is a belt installation guide decal on bottom side of left footrest BELT REMOVAL e Remove mower See TO REMOVE MOWER in this section of manual NOTE Observe entire motion drive belt and position of all belt guides and keepers e Remove belt from stationary idler A and clutching idler B e Remove belt from centerspan idler C e Pull belt slack toward rear of tractor Remove belt upwards from transaxle input pulley D e Remove belt downward from engine pulley E e Slide belt toward rear of tractor off the steering plate F and remove from tractor BELT INSTALLATION e Install new belt from tractor rear to front over the steer ing plate F and above clutch brake pedal shaft G2. EH Husqvarna SAFETY RULES Safe Operation Practices for Ride On Mowers A DANGER THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE WARNING In order to prevent acci dental starting when setting up trans porting adjusting or making repairs always disconnect spark plug wire and place wire where it cannot contact spark plug WARNING Do not coast down a hill in neutral you may lose control of the tractor WARNING Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor Use common sense when towing Operate only at the low est possible speed when on a slope Too heavy of a load while on a slope is dangerous Tires can lose traction with the ground and cause you to lose control of your tractor WARNING Engine exhaust some of its constituents and cer tain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm WARNING Battery posts terminals and related accessories contain lead and lead compounds chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling GENERAL OPERATION Read understand and follow all instructions on the machine and in the manual before starting Do not put hands or feet near rotating parts or
3. ENGINE e Move throttle control D between half and full speed fast position NOTE Failure to move throttle control between half and full speed fast position before stopping may cause en gine to backfire e Turn ignition key F to STOP position and remove key Always remove key when leaving tractor to prevent unauthorized use e Never use choke N to stop engine IMPORTANT Leaving the ignition switch in any position other than STOP will cause the battery to discharge and go dead NOTE Under certain conditions when tractor is standing idle with the engine running hot engine exhaust gases may cause browning of grass To eliminate this possibility al ways stop engine when stopping tractor on grass areas CAUTION Always stop tractor com pletely as described above and set parking brake before leaving the operator s position FIG 6 TO USE THROTTLE CONTROL D See Fig 6 Always operate engine at full speed fast e Operating engine at less than full speed fast reduces engine s operating efficiency e Full speed fast offers the best mower performance OPERATION TO MOVE FORWARD AND BACKWARD See Fig 7 The direction and speed of movement is controlled by the gearshift lever J FIG 7 e Start tractor with clutch brake pedal depressed and gearshift lever in neutral N position e Move gearshift lever to desired position e Slowly release clutch brake pedal to sta
4. Service more often when operating in dirty or dusty conditions GENERAL RECOMMENDATIONS The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence Toreceive full value from the warranty operator must maintain tractor as instructed in this manual Some adjustments will need to be made periodically to properly maintain your tractor At least once a season check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual e At least once a year you should replace the spark plug clean or replace air filter and check blades and belts for wear A new Spark plug and clean air filter assure proper air fuel mixture and help your engine run better and last longer BEFORE EACH USE e Check engine oil level e Check brake operation e Check tire pressure e Check operator presence and ROS systems for proper operation e Check for loose fasteners 15 a S A aa ava S EA LHe EZ SS So _ aS SS ER SS oo S E SS ae RE _ 4 MUNNS o S S S S S RE 1 2 2 SS S E S SS SS a y 2 SE as oo SS SS 2 SOH 210 921 U9SJUIEUU 3 Replace blades more often when mowing in sandy soil 4 Not required if equipped with maintenance free battery LUBRICATION CHART r D SAE 30 or 10w30 motor oil General Purpose Grease Refer to Maintenance ENGIN
5. bent or loose blade Bent blade mandrel Loose damaged part s 25 CORRECTION 10 oe eS NE oo a NS oe el oa ear ee NE Sanaa eNS Fill fuel tank See TO START ENGINE in Operation section Wait several minutes before attempting to start Replace spark plug Clean replace air filter Replace fuel filter Empty fuel tank and carburetor refill tank with fresh gasoline and replace fuel filter Check all wiring See To Adjust Carburetor in Service Adjustments section Contact an authorized service center department Clean replace air filter Replace spark plug Recharge or replace battery Replace fuel filter Empty fuel tank and refill tank with fresh clean gasoline Check all wiring See To Adjust Carburetor in Service Adjustments section Contact an authorized service center department Depress clutch brake pedal Disengage attachment clutch Recharge or replace battery Replace fuse Clean battery terminals Check all wiring Check replace ignition switch Check replace solenoid or starter Contact an authorized service center department Recharge or replace battery Clean battery terminals Check all wiring Check replace solenoid or starter Raise cutting height reduce speed Adjust throttle control Clean underside of mower housing Clean replace air filter Check oil level change oil Clean and regap or change spark plug Replace fuel fi
6. e Pull belt toward front of tractor and roll belt onto engine pulley E e Pull belt toward rear of tractor Carefully work belt down around transaxle input pulley D Be sure belt is inside the belt keeper e Install belt on centerspan idler C e Install belt through stationary idler A and clutching idler B e Make sure belt is in all pulley grooves and inside all belt guides and keepers e Install mower See TO INSTALL MOWER in this sec tion of manual aN ED i FIG 27 SERVICE AND ADJUSTMENTS FRONT WHEEL TOE IN CAMBER Your new tractor front wheel toe in and camber is set at the factory and is normal The front wheel toe in and camber are not adjustable If damage has occurred to affect the factory set front wheel toe in or camber contact a qualified service center TO REMOVE WHEEL FOR REPAIRS ose Fig 28 Block up axle securely e Remove axle cover retaining ring and washers to allow wheel removal rear wheel contains a square key Do not lose e Repair tire and reassemble e Onrear wheels only align grooves in rear wheel hub and axle Insert square key e Replace washers and snap retaining ring securely in axle groove e Replace axle cover NOTE To seal tire punctures and prevent flat tires due to slow leaks tire sealant may be purchased from your local parts dealer Tire sealant als
7. Charging System 15 Amps 3600 RPM Battery AMP HR 35 Min CCA 280 Case Size U1R Blade Torque 45 55 FT LBS C Spark Plug Ground Speed MPH CONGRATULATIONS on your purchase of a new tractor It has been designed engineered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily rem edy please contact your nearest authorized service center department We have competent well trained technicians and the proper tools to service or repair this tractor Please read and retain this manual The instructions will enable you to assemble and maintain your tractor properly Always observe the SAFETY RULES CUSTOMER RESPONSIBILITIES e Read and observe the safety rules e Follow a regular schedule in maintaining caring for and using your tractor e Follow the instructions under Maintenace and Stor age sections of this owner s manual WARNING This tractor is equipped with an internal com bustion engine and should not be used on or near any unimproved forest covered brush covered or grass covered land unless the engine s exhaust system is equipped with a spark arrester meeting applicable local or state laws if any If a spark arrester is used it should be maintained in effective working order by the operator In the state of California the above is required by law Section 4442 of the California Public Resources Code
8. Never allow children to operate the machine Use extra care when approaching blind corners shrubs trees or other objects that may block your view of a child IV TOWING Tow only with a machine that has a hitch designed for towing Do not attach towed equipment except at the hitch point Follow the manufacturer s recommendation for weight limits for towed equipment and towing on slopes Never allow children or others in or on towed equip ment On slopes the weight of the towed equipment may cause loss of traction and loss of control Travel slowly and allow extra distance to stop V SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or property damage use extreme care in handling gasoline Gasoline is extremely flammable and the vapors are explosive Extinguish all cigarettes cigars pipes and other sources of ignition Use only approved gasoline container Never remove gas cap or add fuel with the engine run ning Allow engine to cool before refueling Never fuel the machine indoors Never store the machine or fuel container where there is an open flame spark or pilot light such as on a water heater or other appliances Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner Always place containers on the ground away from your vehicle when filling Remove gas powered equipment from the truck or trailer and refuel it on the ground If this is not possible then refuel such
9. Other states may have similar laws Federal laws apply on federal lands TABLE OF CONTENTS SAFETY RULES rae spactapenwesasiweccasanaanevouentaeesesannnanenees 2 3 PRODUCT SPECIFICATIONG ceseeeeeeeeeeeeeeeneees 4 CUSTOMER RESPONSIBILITIES 4 PS SEMBEE street cease gy catenssmep ce scenasevantecenecseeees 5 8 OPERATION case dntetecteestanidetedendyeieeremtaninaeenvian 9 14 MAINTENANCE SCHEDULE ss 15 MAINTENANCE 15 17 SERVICE AND ADJUSTMENTS 18 23 STORAGE wes ea ENEE 24 TROUBLESHOOTING 25 26 CONTENTS OF HARDWARE PACK Slope Sheet aca 1 Hex Bolt Steering Insert Extension Lock Washer Shaft Steering Wheel Steering Boot Steering Wheel Washer Adapter 1 Washer 1 Hex Bolt ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping puposes BEFORE REMOVING TRACTOR FROM When right or left hand is mentioned in this manual it means SKID when you are in the operating position seated behind the steering wheel ATTACH STEERING WHEEL See Fig 1 TO REMOVE TRACTOR FROM ASSEMBLE EXTENSION SHAFT AND BOOT CARTON e Slide extension shaft onto lower steering shaft e Place tabs of steering boot over tab slots in dash and UNPACK CARTON push down to secure Cut along dashed lines on all four panels of carton INSTALL STEERING WHEEL Remove end panels and lay si
10. Unsnap headlight wire connector e Stand in front of tractor Grasp hood at sides tilt toward engine and lift off of tractor e To replace reverse above procedure HEADLIGHT WIRE CONNECTOR FIG 32 ENGINE TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary If adjustment is nec essary see engine manual TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and ad justment should not be necessary If adjustment is neces sary see engne manual TO ADJUST CARBURETOR Your carburetor is not adjustable If your engine does not operate properly due to suspected carburetor problems take your tractor to an authorized service center for repair and or adjustment STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more WARNING Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark Allow the engine to cool before storing in any enclosure TRACTOR Remove mower from tractor for winter storage When mower is to be stored for a period of time clean itthoroughly remove all dirt grease leaves etc Store in a clean dry area e Clean entire tractor See CLEANING in the Mainte nance section of this manual e Inspect and replace belts if necessary See belt re placemen
11. choke as described above COLD WEATHER STARTING 50 F and below e Whenengine starts allow engine to run with the throttle control in the choke N position until the engine runs roughly then move throttle control to fast position This may require an engine warm up period from several seconds to several minutes depending on the tem perature e The attachments can also be used during the engine warm up period NOTE If at a high altitude above 3000 feet or in cold temperatures below 32 F the carburetor fuel mixture may need to be adjusted for best engine performance See TO ADJUST CARBURETOR in the Service and Adjustments section of this manual 14 OWING TIPS Mower should be properly leveled for best mowing per formance See TO LEVEL MOWER HOUSING in the Service and Adjustments section of this manual The left hand side of mower should be used for trim ming Drive so that clippings are discharged onto the area that has been cut Have the cut area to the right of the machine This will result in a more even distribution of clippings and more uniform cutting When mowing large areas start by turning tothe right so that clippings will discharge away from shrubs fences driveways etc After one or two rounds mow in the opposite direction making left hand turns until finished See Fig 11 If grass is extremely tall it should be mowed twice to reduce load and possible fire hazard from dried clip
12. equipment with a portable container rather than from a gasoline dispenser nozzle Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete Do not use a nozzle lock open device If fuel is spilled on clothing change clothing immedi ately Never overfill fuel tank Replace gas cap and tighten securely SAFETY RULES Safe Operation Practices for Ride On Mowers GENERAL SERVICE Never operate machine in a closed area Keep all nuts and bolts tight to be sure the equipment is in safe working condition Never tamper with safety devices Check their proper operation regularly Keep machine free of grass leaves or other debris build up Clean oil or fuel spillage and remove any fuel soaked debris Allow machine to cool before storing If you strike a foreign object stop and inspect the machine Repair if necessary before restarting Never make any adjustments or repairs with the engine running Check grass catcher components and the discharge guard frequently and replace with manufacturer s rec ommended parts when necessary Mower blades are sharp Wrap the blade or wear gloves and use extra caution when servicing them Check brake operation frequently Adjust and service as required Maintain or replace safety and instruction labels as necessary Be sure the area is clear of bystanders before operat ing Stop machine if anyone enters the area
13. familiar with all controls their location and function Operate them before you start the engine Be sure brake system is in safe operating condition Be sure Operator Presence System and Reverse Op eration System ROS are working properly See the Operation and Maintenance sections in this manual N NN ALAS NN NOUN OPERATION These symbols may appear on your tractor or in literature supplied with the product Learn and understand their mean ing ED R N H L N om Q REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW Pp IGNITION SWITCH AO m 2 Mir Eg ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE MOWER HEIGHT MOWER LIFT OPERATION SYSTEM ROS n _ D 4 1 t BED fa d ty Cruise CLUTCH BRAKE LIGHTS ON FUEL BATTERY REVERSE FORWARD CRUISE CONTROL SEDAL w ox ATTACHMENT ATTACHMENT DANGER KEEP HANDS CLUTCH DISENGAGED CLUTCH ENGAGED AND FEET AWAY KEEP AREA CLEAR SLOPE HAZARDS SEE SAFETY RULES SECTION DANGER indicates a hazard which if not avoided will result in death or serious injury WARNING indicates a hazard which if not avoided could result in death or serious injury CAUTION indicates a hazard which if not avoided might result in minor or moderate injury A CAUTION when used without the alert symbol indicates a situation that could result in damage to the tractor and or engine FREE WHEEL Automatic Models only Failure to follow instructions could result in serio
14. into the hole in the backside of the grill e Close hood INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly stop running or prevent it from starting e Check wiring See electrical wiring diagram in the Repair Parts section SERVICE AND ADJUSTMENTS TO REPLACE FUSE Replace with 20 amp automotive type plug in fuse The fuse holder is located behind the dash REPLACING BATTERY See Fig 30 AND 31 WARNING Do not short battery ter minals by allowing a wrench or any other object to contact both terminals at the same time Before connect ing battery remove metal bracelets wristwatch bands rings etc Positive terminal must be connected first to prevent sparking from acci dental grounding e Lift seat pan to raised position and open battery box door e Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor e Install new battery with terminals in same position as old battery e First connect RED battery cable to positive ter minal with hex bolt and keps nut as shown Tighten securely e Connect BLACK grounding cable to negative ter minal with remaining hex bolt and keps nut Tighten securely e Close battery box door SEAT PAN BATTERY BOX DOOR NEGATIVE BLACK CABLE POSITIVE RED CABLE FIG 31 23 TO REMOVE HOOD AND GRILL ASSEMBLY See Fig 32 e Raise hood e
15. lower mower Turn nut right to raise mower FIG 21 NOTE Each full turn of adjustment nut will change mower height about 3 16 e Test your adjustment by mowing some uncut grass and visually checking the appearance Readjust if necessary until you are satisfied with the results PRECISION SIDE TO SIDE ADJUSTMENT See Fig 22 e With all tires properly inflated park tractor on level ground or driveway CAUTION Blades are sharp Protect your hands with gloves and or wrap blade with heavy cloth e Raise mower to its highest position e At both sides of mower position blade at side and measure the distance A from bottom edge of blade to the ground The distance should be the same on both sides e If adjustment is necessary see step in Visual Adjust ment instructions above e Recheck measurements adjust if necessary until both sides are equal FRONT TO BACK ADJUSTMENT See Figs 23 and 24 IMPORTANT Deck must be level side to side To obtain the best cutting results the mower blades should be adjusted so the front tip is 1 8 to 1 2 lower than the rear tip when the mower is in its highest position CAUTION Blades are sharp Protect your hands with gloves and or wrap blade with heavy cloth e Raise mower to highest position e Position any blade so the tip is pointing straight forward Measure distance B to the ground at front and rear tip of the blade e If fr
16. DJUSTMENTS tor Insert rod end of link assembly through front hole in tractor front suspension bracket F e Insert end of link E into hole in front mower bracket and secure with washer and retainer spring J e Hook end of clutch cable spring Q into hole in idler FIG 17 on rear mower bracket and secure with washer and retainer spring ATTACH FRONT LINK E Work from left side of trac FIG 19 arm R e Push clutch cable housing guide P into bracket slide collar L onto guide and secure with retainer spring K e Install belt on engine pulley M in belt keepers G IMPORTANT CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES e Raise attachment lift lever to highest position e If necessary adjust gauge wheels before operating mower as shown in the Operation section of this manual 0304 2tex 19 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires If tires are over or under inflated it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly VISUAL SIDE TO SIDE ADJUSTMENT See Fig 21 e With all tires properly inflated and if your lawn appears unevenly cut determine which side of mower is cutting lower e With a 3 4 or adjustable wrench turn lift link adjust ment nut A to the left to lower LH side of mower or to the right to raise LH side of mower Turn nut left to
17. E Section IMPORTANT DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF LUBRICATING BEARINGS IF YOU FEEL THEY MUST BE LUBRICATED USE ONLY A DRY POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY MAINTENANCE TRACTOR Always observe safety rules when performing any main tenance BRAKE OPERATION lf tractor requires more than five 5 feet to stop at highest speed in highest gear on a level dry concrete or paved surface then brake must be checked and adjusted See TO ADJUST BRAKE in the Service and Adjustments section of this manual TIRES e Maintain proper air pressure in all tires See PRODUCT SPECIFICATIONS section of this manual e Keep tires free of gasoline oil or insect control chemi cals which can harm rubber e Avoid stumps stones deep ruts sharp objects and other hazards that may cause tire damage NOTE To seal tire punctures and prevent flat tires due to slow leaks tire sealant may be purchased from your local parts dealer Tire sealant also prevents tire dry rot and corrosion OPERATOR PRESENCE SYSTEM AND REVERSE OP ERATION SYSTEM ROS Be sure operator presence and reverse operation systems are working properly If your tractor does not function as described repair the problem immediately e The engine should not start unless the brake pedal is fully depressed and the attach
18. HAUST AREAS ARE STILL WARM TROUBLESHOOTING POINTS PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power Excessive vibration ee Se ee oe ae oe oe ee a CAUSE Out of fuel Engine not CHOKED properly Engine flooded Bad spark plug Dirty air filter Dirty fuel filter Water in fuel Loose or damaged wiring Carburetor out of adjustment Engine valves out of adjustment Dirty air filter Bad spark plug Weak or dead battery Dirty fuel filter Stale or dirty fuel Loose or damaged wiring Carburetor out of adjustment Engine valves out of adjustment Clutch brake pedal not depressed Attachment clutch is engaged Weak or dead battery Blown fuse Corroded battery terminals Loose or damaged wiring Faulty ignition switch Faulty solenoid or starter Faulty operator presence switch es Weak or dead battery Corroded battery terminals Loose or damaged wiring Faulty solenoid or starter Cutting too much grass too fast Throttle in CHOKE position Build up of grass leaves and trash under mower Dirty air filter Low oil level dirty oil Faulty spark plug Dirty fuel filter Stale or dirty fuel Water in fuel Spark plug wire loose Dirty engine air screen fins Dirty clogged muffler Loose or damaged wiring Carburetor out of adjustment Engine valves out of adjustment Worn
19. Never carry passengers Do not mow in reverse unless absolutely necessary Always look down and behind before and while back ing Never carry children even with the blades shut off They may fall off and be seriously injured or interfere with safe machine operation Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine Keep children out ofthe mowing area and in the watchful care of a responsible adult other than the operator Be alert and turn machine off if a child enters the area Before and while backing look behind and down for small children Mow up and down slopes 15 Max not across Choose a low ground speed so that you will not have to stop or shift while on the slope Avoid starting stopping or turning on a slope If the tires lose traction disengage the blades and proceed slowly straight down the slope If machine stops while going uphill disengage blades shift into reverse and back down slowly Do not turn on slopes unless necessary and then turn slowly and gradually downhill if possible PRODUCT SPECIFICATIONS Gasoline Capacity 1 50 Gallons and Type Unleaded Regular Oil Type API SG SL SAE 10W30 above 32 F SAE 5W 30 below 32 F Oil Capacity W Filter 51 oz W O Filter 35 oz Champion RC12YC Gap 030 Forward ist 1 2 2nd 1 5 3rd 2 4 4th 3 5 5th 4 8 6th 5 3 Reverse 1 5
20. PROPER POSITION OF ALL BELTS see the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual Verify that the belts are routed correctly CHECK BRAKE SYSTEM After you learn howto operate your tractor check to see that the brake is operating properly See TO CHECK BRAKE in the Service and Adjustments section of this manual CHECKLIST BEFORE YOU OPERATE YOUR NEW TRACTOR WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PER FORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT PLEASE REVIEW THE FOLLOWING CHECKLIST Y All assembly instructions have been completed No remaining loose parts in carton Battery is properly prepared and charged Minimum 1 hour at 6 amps Seat is adjusted comfortably and tightened securely All tires are properly inflated For shipping purposes the tires were overinflated at the factory Be sure mower deck is properly leveled side to side front to rear for best cutting results Tires must be properly inflated for leveling Check mower and drive belts Be sure they are routed properly around pulleys and inside all belt keepers Check wiring See that all connections are still secure and wires are properly clamped WHILE LEARNING HOW TO USE YOUR TRACTOR PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS Y Engine oil is at proper level Fuel tank is filled with fresh clean regular unleaded gasoline Become
21. crossing road ways Use extra care when loading or unloading the machine into a trailer or truck Always wear eye protection when operating ma chine Data indicates that operators age 60 years and above are involved in a large percentage of riding mower re lated injuries These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury Follow the manufacturer s recommendation for wheel weights or counterweights Keep machine free of grass leaves or other debris build up which can touch hot exhaust engine parts and burn Do not allow the mower deck to plow leaves or other debris which can cause build up to occur Clean any oil or fuel spillage before operating or storing the machine Allow machine to cool before storage ll SLOPE OPERATION Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death Operation on all slopes requires extra caution If you cannot back up the slope or if you feel uneasy on it do not mow it Mow up and down slopes not across Watch for holes ruts bumps rocks or other hidden objects Uneven terrain could overturn the machine Tall grass can hide obstacles Choose a low ground speed so that you will not have to stop or shift while on the slope Do not mow on wet grass Tires may lose traction Always keep the machine in gear when going down slopes Do n
22. de panels flat e Check for any additional loose parts or cartons and remove e Position front wheels of the tractor so they are pointing straight forward e Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension e Position steering wheel so cross bars are horizontal left to right and slide inside boot and onto adapter e Assemble large flat washer 5 16 lock washer 5 16 hex ASSEMBLY bolt and tighten securely e Snap steering wheel insert into center of steering wheel e Remove protective materials from tractor hood and grill IMPORTANT CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID INSERT Len HEX BOLT p 5 16 LOCK WASHER gt LARGE FLAT WASHER STEERING WHEEL ADAPTER LOWER STEERING SHAFT STAR SEAT See Figs 2A and 2B Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor Remove the cardboard packing and discard e Connect switch to seat e Place seat on seat pan so all three 3 bottom pads are positioned over large slotted holes in pan e Push down on seat to engage pads in slots and pull seat towards rear of tractor e Raise seat and tighten bolt securely e Remove tape and discard e Lower seat into operating position and sit on seat Press clutch brake pedal all the way down If operating position is not comfortable adjust s
23. eat To adjust seat Grasp adjustment handle and pull up slide seat to desired position and release adjustment handle TAPE WIRING HARNESS SEAT PAN ADJUSTMENT BOLT TAB HANDLE CHECK BATTERY See Fig 3 Lift seat pan to raised position and open battery box door e If this battery is put into service after month and year indicated on label label located between terminals charge battery for minimum of one hour at 6 10 amps See BATTERY in Maintenance section ofthis manual for charging instructions SEAT PAN BOX DOOR TERMINAL ASSEMBLY NOTE You may now roll or drive your tractor off the skid Follow the appropriate instruction below to remove the tractor from the skid WARNING Before starting read understand and follow all instructions in the Operation section of this manual Be sure tractor is in a well ventilated area Be sure the area in front of tractor is clear of other people and objects TO ROLL TRACTOR OFF SKID See Op eration section for location and function of controls e Raise attachment lift lever to its highest position e Release parking brake by depressing clutch brake pedal e Place gearshift lever in neutral N position e Roll tractor forward off skid TO DRIVE TRACTOR OFF SKID See Op eration section for location and function of controls A WARNING Before starting read understand and follow all instructions in the Operation section
24. el lines and carburetor are empty e Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur e Use fresh fuel next season NOTE Fuel stabilizer is an acceptable alternative in mini mizing the formation of fuel gum deposits during storage Add stabilizer to gasoline in fuel tank or storage container Always follow the mix ratio found on stabilizer container Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor Do not empty the gas tank and carburetor if using fuel stabilizer ENGINE OIL Drain oil with engine warm and replace with clean en gine oil See ENGINE in the Maintenance section of this manual CYLINDER S Remove spark plug s e Pour one ounce of oil through spark plug hole s into cylinder s e Turn ignition key to START position for a few seconds to distribute oil e Replace with new spark plug s OTHER Do not store gasoline from one season to another e Replace your gasoline can if your can starts to rust Rust and or dirt in your gasoline will cause problems e f possible store your tractor indoors and cover it to give protection from dust and dirt e Cover your tractor with a suitable protective cover that does not retain moisture Do not use plastic Plastic cannot breathe which allows condensation to form and will cause your tractor to rust IMPORTANT NEVER COVER TRACTOR WHILE ENGINE AND EX
25. h slopes greater than 15 and do not drive across any slope o the slowest speed before starting up or down ills e Avoid stopping or changing speed on hills e f stopping is absolutely necessary push clutch brake pedal quickly to brake position and engage parking brake e Move gearshift lever to 1st gear Be sure you have allowed room for tractor to roll slightly as you restart movement e Torestart movement slowly release parking brake and clutch brake pedal e Make all turns slowly 13 TRANSPORT Raise attachmentliftto highest position with attachment lift control e When pushing or towing your tractor be sure gearshift lever is in neutral N position e Do not push or tow tractor at more than five 5 MPH NOTE To protect hood from damage when transporting your tractor on a truck or a trailer be sure hood is closed and secured to tractor Use an appropriate means of tying hood to tractor rope cord etc TOWING CARTS AND OTHER ATTACH MENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac tor Use common sense when towing Too heavy of a load while on a slope is dangerous Tires can lose traction with the ground and cause you to lose control of your tractor BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped from the factory already filled with summer weight oil e Check engi
26. hever comes first Spark plug type and gap setting is shown in PRODUCT SPECIFICATIONS section of this manual IN LINE FUEL FILTER See Fig 15 The fuel filter should be replaced once each season If fuel filter becomes clogged obstructing fuel flow to carburetor replacement is required e With engine cool remove filter and plug fuel line sec tions e Place new fuel filter in position in fuel line with arrow pointing towards carburetor e Be sure there are no fuel line leaks and clamps are properly positioned e Immediately wipe up any spilled gasoline SERVICE AND ADJUSTMENTS WARNING TO AVOID SERIOUS INJURY BEFORE PERFORMING ANY SERVICE OR ADJUST MENTS Depress clutch brake pedal fully and set parking brake Place gearshift lever in neutral N position Place attachment clutch in DISENGAGED position Turn ignition key to STOP and remove key Make sure the blades and all moving parts have completely stopped Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug TO REMOVE MOWER See Fig 16 Place attachment clutch in DISENGAGED position e Lower attachment lift lever to its lowest position e Roll belt off engine pulley M and belt keepers G e Remove retainer spring K slide collar L off and push housing guide P out of bracket e Remove clutch cable spring Q from idler arm R e Disconnect front link E from mower re
27. is manual Clean around mandrels to open vent holes Turn light switch ON Replace bulb s or lamp s Check replace light switch Check wiring and connections Replace fuse Replace battery Check clean all connections Replace regulator Replace alternator Move throttle control between half and full speed fast position before stopping engine SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL NOT ACROSS HILL 15 DEGREES MAX WARNING To avoid serious injury operate your tractor up and down the face of slopes never across the face Do not mow slopes greater than 15 degrees Make turns gradually to prevent tipping or loss of control Exercise extreme caution when changing direction on slopes 1 Fold this page along dotted line indicated above 2 Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure 3 Sight across the fold in the direction of hill slope you want to measure 4 Compare the angle of the fold with the slope of the hill 27 532 41 01 85 03 05 07 JS D Husqvarna Printed in U S A
28. k start the engine and let it run until the fuel lines and carburetor are empty Use fresh fuel next season See Storage Instructions for additional information Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur TO START ENGINE See Fig 3 When starting the engine for the first time or if the engine has run out of fuel it will take extra cranking time to move fuel from the tank to the engine e Sit on seat in operating position depress clutch brake pedal and set parking brake e Place gear shift lever in neutral N position e Move attachment clutch to DISENGAGED position e Move throttle control to choke N position NOTE Before starting read the warm and cold starting procedures below e Insertkey into ignition and turn key clockwise to START position and release key as soon as engine starts Do not run starter continuously for more than fifteen seconds per minute If the engine does not start after several attempts move throttle control to fast position wait a few minutes and try again If engine still does not start move the throttle control back to the choke N position and retry WARM WEATHER STARTING 50 F and above e When engine starts move the throttle control to the fast position e Theattachments and ground drive can now be used If the engine does not accept the load restart the engine and allow it to warm up for one minute using the
29. lter Empty fuel tank and refill tank with fresh clean gasoline Empty fuel tank and carburetor refill tank with fresh gasoline and replace fuel filter Connect and tighten spark plug wire Clean engine air screen fins Clean replace muffler Check all wiring See To Adjust Carburetor in Service Adjustments section Contact an authorized service center department Replace blade Tighten blade bolt Replace blade mandrel Tighten loose part s Replace damaged parts TROUBLESHOOTING POINTS PROBLEM Engine dies when tractor is shifted into reverse Engine continues to run when operator leaves seat with attachment clutch engaged Poor cut uneven Mower blades will not rotate Poor grass discharge Headlight s not working if so equipped Battery will not charge Engine backfires when turning engine OFF 1 L nie NON OL ER A ee CAUSE Reverse operation system ROS is not ON while mower or other attachment is engaged Faulty operator safety presence control system Worn bent or loose blade Mower deck not level Buildup of grass leaves and trash under mower Bent blade mandrel Clogged mower deck vent holes from buildup of grass leaves and trash around mandrels Obstruction in clutch mechanism Worn damaged mower drive belt Frozen idler pulley Frozen blade mandrel Engine speed too slow Travel speed too fast Wet grass Mowe
30. ment clutch control is in the disengaged position CHECK OPERATOR PRESENCE SYSTEM e Whenthe engine is running any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine e When the engine is running and the attachment clutch is engaged any attempt by the operator to leave the seat should shut off the engine e The attachment clutch should never operate unless the operator is in the seat CHECK REVERSE OPERATION ROS SYSTEM e When the engine is running with the ignition switch in the engine ON position and the attachment clutch engaged any attempt by the operator to shift into reverse should shut off the engine e When the engine is running with the ignition switch in the ROS ON position and the attachment clutch en gaged any attempt by the operator to shift into reverse should NOT shut off the engine ROS ON POSITION ENGINE ON POSITION NORMAL OPERATING 16 BLADE CARE For best results mower blades must be sharp Replace bent worn or damaged blades CAUTION Use onlyareplacementblade approved by the manufacturer of your tractor Using a blade not approved by the manufacturer of your tractor is hazardous could damage your tractor and void your warranty BLADE REMOVAL See Fig 12 e Raise mower to highest position to allow access to blades NOTE Protect your hands with gloves and or wrap blade with heavy cloth e Remove blade bolt by
31. move retainer spring and washer e Go to either side of mower and disconnect mower suspension arm A from chassis pin B and rear lift link C from rear mower bracket D remove retainer springs and washers CAUTION AFTER REAR LIFT LINKS ARE DISCONNECTED THE ATTACH MENT LIFT LEVER WILL BE SPRING LOADED HAVE A TIGHT GRIP ON LIFT LEVER WHEN CHANGING POSITION OF THE LEVER e Slide mower out from under right side of tractor IMPORTANT IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR REMOVE THE FRONT LINK E AND REAR LIFT LIKS C FROM TRACTOR AND HOOK THE CLUTCH SPRING Q INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH TO INSTALL MOWER See Fig 16 19 Be sure tractor is on level surface and engage parking brake e Lower attachment lift lever to it s lowest position CAUTION LIFT LEVER IS SPRING LOADED HAVE A TIGHT GRIP ON LIFT LEVER LOWER IT SLOWLY AND ENGAGE IN LOWEST POSITION NOTE Be sure mower side suspension arms A are point ing forward before sliding mower under tractor e Slide mower under tractor until it is centered under tractor e ATTACH MOWER SIDE SUSPENSION ARMS A TO CHASSIS Position hole in arm over pin B on outside of tractor chassis and secure with retainer spring e Repeat on opposite side of tractor e ATTACH REAR LIFT LINKS C Lift rear corner of mower and position slot in link assembly over pin D 03042 tex SERVICE AND A
32. n the operator decides it is necessary to reposition the machine with the attachment engaged Do not mow in reverse unless absolutely necessary USING THE REVERSE OPERATION SYSTEM e Depress clutch brake pedal all the way down and hold e With engine running turn ignition key counterclockwise to ROS ON position e Look down and behind before backing e Move gear shift lever to reverse R position and slowly release clutch brake pedal to start movement e When use of the ROS is no longer needed turn the ignition key clockwise to engine ON position ROS ON POSITION ENGINE ON POSITION NORMAL OPERATING O OPERATION TO OPERATE MOWER See Fig 10 Your tractor is equipped with an operator presence sensing switch Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough rolling terrain or hills e Select desired height of cut with attachment lift lever e Start mower blades by engaging attachment clutch control TO STOP MOWER BLADES disengage attachment clutch control CAUTION Do not operate the mower without either the entire grass catcher on mowers So equipped or the deflector shield S in place FIG 10 TO OPERATE ON HILLS WARNING Do not drive up or down hills wit
33. ne oil with tractor on level ground e Pull up and remove oil fill cap dipstick wipe oil off Re insert the dipstick into the tube and push down firmly into place Remove and read oil level If necessary add oil until FULL mark on dipstick is reached Do not overfill e For cold weather operation you should change oil for easier starting See OIL VISCOSITY CHART in the Maintenance section of this manual e To change engine oil see the Maintenance section in this manual a GASOLINE Fill fuel tank to bottom of filler neck Do not overfill Use fresh clean regular unleaded gasoline with a minimum of 87 octane Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life Do not mix oil with gasoline Purchase fuel in quantities that can be used within 30 days to assure fuel freshness CAUTION Wipe off any spilled oil or fuel Do not store spill or use gasoline near an open flame IMPORTANT WHEN OPERATING IN TEMPERATURES BELOW32 F 0 C USE FRESH CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING OPERATION CAUTION Alcohol blended fuels called gas ohol or using ethanol or methanol can attract moisture which leads to separation and for mation of acids during storage Acidic gas can damage the fuel system of an engine while in storage To avoid engine problems the fuel system should be emptied before storage of 30 days or longer Drain the gas tan
34. o prevents tire dry rot and corrosion RETAINING WASHERS RING AXLE COVER SQUARE KEY REAR_____ WHEEL ONLY TO START ENGINE WITH A WEAK BATTERY See Fig 29 WARNING Lead acid batteries gen erate explosive gases Keep sparks flame and smoking materials away from batteries Always wear eye protection when around batteries If your battery is too weak to start the engine it should be recharged See BATTERY in the Maintenance section of this manual If jumper cables are used for emergency starting follow this procedure IMPORTANT YOUR TRACTORIS EQUIPPED WITHA 12VOLT SYSTEM THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES TO ATTACH JUMPER CABLES e Connect one end of the RED cable to the POSITIVE terminal of each battery A B taking care not to short against tractor chassis e Connectone end ofthe BLACK cable to the NEGATIVE terminal C of fully charged battery e Connect the other end of the BLACK cable D to good chassis ground away from fuel tank and battery TO REMOVE CABLES REVERSE ORDER e BLACK cable first from chassis and then from the fully charged battery e RED cable last from both batteries WEAK OR DEAD FULLY CHARGED BATTERY BATTERY FIG 29 19 REPLACE HEADLIGHT BULB Raise hood e Pull bulb holder out of the hole in the backside of the grill e Replace bulb in holder and push bulb holder securely back
35. of this manual Be sure tractor is in a well ventilated area Be sure the area in front of tractor is clear of other people and objects e Be sure all the above assembly steps have been com pleted e Check engine oil level and fill fuel tank with gasoline e Sit on seat in operating position depress clutch brake pedal and set the parking brake e Place gear shift lever in neutral N position e Raise attachment lift lever to its highest position e Remove key from bag and start the engine see TO START ENGINE in the Operation section of this manual After engine has started move throttle control to idle slow position e Depress clutch brake pedal into full BRAKE position and hold Move gearshift lever to 1st gear e Slowly release clutch brake pedal and slowly drive tractor off skid e Apply brake to stop tractor set parking brake and place gearshift lever in neutral position e Turn ignition key to STOP position Continue with the instructions that follow ATTACH HOOD SCOOP See Fig 4 FIG 4 ASSEMBLY CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes Correct tire pressure is important for best cutting performance e Reduce tire pressure to PSI shown on tires CHECK DECK LEVELNESS For best cutting results mower housing should be properly leveled See TO LEVEL MOWER in the Service and Adjustments section of this manual CHECK FOR
36. ont tip of blade is not 1 8 to 1 2 lower than the rear FIG 23 tip go to the front of tractor e With an 11 16 or adjustable wrench loosen jam nut A several turns to clear adjustment nut B e With a 3 4 or adjustable wrench turn front link adjust ment nut B clockwise Itighten to raise the front of mower or counterclockwise loosen to lower the front mower Loosen adjust Tighten adjust nut nut B to lower B to raise mower Loosen jam nut A first FIG 24 NOTE Each full turn of the adjustment nut will change mower height about 1 8 e Recheck measurements adjust if necessary until front tip of blade is 1 8 to 1 2 lower than the rear tip e Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut SERVICE AND ADJUSTMENTS To Replace Mower Drive Belt See Fig 26 MOWER DRIVE BELT REMOVAL Park tractor on a level surface Engage parking brake Lower attachment lift lever to its lowest position Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface Remove belt from clutch pulley M both mandrel pul leys R and all idler pulleys S MOWER DRIVE BELT INSTALLATION Install belt around both mandrel pulleys R and around idler pulleys S as shown Install belt onto clutch pulley M IMPORTANT Check belt for proper routing in all mower pulley grooves 3 Raise attachment lift lever to highest position _h
37. ot shift to neutral and coast downhill Avoid starting stopping or turning on a slope If the tires lose traction disengage the blades and proceed slowly straight down the slope Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction which could cause the machine to roll over Use extra care while operating machine with grass catchers or other attachments they can affect the stability of the machine Do no use on steep slopes Do not try to stabilize the machine by putting your foot on the ground Do not mow near drop offs ditches or embankments The machine could suddenly roll over if a wheel is over the edge or if the edge caves in lll CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the machine and the mowing activity Never assume that children will remain where you last saw them Keep children out ofthe mowing area and in the watchful care of a responsible adult other than the operator Be alert and turn machine off if a child enters the area Before and while backing look behind and down for small children Never carry children even with the blades shut off They may fall off and be seriously injured or interfere with safe machine operation Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine
38. pings Make first cut relatively high the second to the desired height Do not mow grass when it is wet Wet grass will plug mower and leave undesirable clumps Allow grass to dry before mowing Always operate engine at full throttle when mow ing to assure better mowing performance and proper discharge of material Regulate ground speed by se lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired When operating attachments select a ground speed that will suit the terrain and give best performance of the attachment being used MAINTENANCE BEFORE EACH USE MAINTENANCE dd EVERY 100 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY BEFORE SEASON STORAGE CA CAS PS AS PS PS A VOHAOPI Inspect Muffler Spark Arrester Replace Oil Filter If equipped Check Tire Pressure VY Check for Loose Fasteners f ef Check Replace Mower Blades f Lubrication Chart f Check Battery Level f Clean Battery and Terminas f Check Transaxle Cooling f Check Mower Levelness f CheckV Belts od Change Engine Oil with oilfiter Change Engine Oil without oil fite9f Clean Air Fiter o o o Clean Air Screen f o Inspect Muffler Spark Arrester J Replace Oil Filter If equipped J Clean Engine Cooling Fins f Replace Spark Plug Replace Air Filter Paper Cartridge J Replace Fuel Fiter____ 1 Change more often when operating under a heavy load or in high ambient temperatures 2
39. r deck not level Low uneven tire air pressure Worn bent or loose blade Buildup of grass leaves and trash under mower Mower drive belt worn Blades improperly installed Improper blades used Clogged mower deck vent holes from buildup of grass leaves and trash around mandrels Light switch is OFF Bulb s or lamp s burned out Faulty light switch Loose or damaged wiring Blown fuse Bad battery cell s Poor cable connections Faulty regulator if so equipped Faulty alternator Engine throttle control not set between half and full speed fast position before stopping engine 26 ee ys ae ha EURE PS wi ele ee CORRECTION Turn ignition key to ROS ON position See Operation section Check wiring switches and connections If not corrected contact an authorized service center department Replace blade Tighten blade bolt Level mower deck Clean underside of mower housing Replace blade mandrel Clean around mandrels to open vent holes Remove obstruction Replace mower drive belt Replace idler pulley Replace blade mandrel Place throttle control in FAST position Shift to slower speed Allow grass to dry before mowing Level mower deck Check tires for proper air pressure Replace sharpen blade Tighten blade bolt Clean underside of mower housing Replace mower drive belt Reinstall blades sharp edge down Replace with blades listed in th
40. rt move ment IMPORTANT Bringtractorto acomplete stop before shifting or changing gears Failure to do so will shorten the useful life of your transaxle TO ADJUST MOWER CUTTING HEIGHT See Fig 8 The position of the attachment lift lever A determines the cutting height FIG 8 e Put attachment lift lever in desired cutting height slot The cutting height range is approximately 1 to 4 The heights are measured from the ground to the blade tip with the engine not running These heights are approximate and may vary depending upon soil conditions height of grass and types of grass being mowed e Theaverage lawn should be cut to approximately 2 1 2 inches during the cool season and to over 3 inches during hot months For healthier and better looking lawns mow often and after moderate growth e For best cutting performance grass over 6 inches in height should be mowed twice Make the first cut relatively high the second to desired height 12 REVERSE OPERATION SYSTEM ROS Your tractor is equipped with a Reverse Operation System ROS Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS ON position A WARNING Backing up with the attachment clutch en gaged while mowing is strongly discouraged Turning the ROS ON to allow reverse operation with the attachment clutch engaged should only be done whe
41. s for deterioration and wear after 100 hours and replace if necessary The belts are not adjustable Replace belts if they begin to slip from wear TRANSAXLE COOLING Keep transaxle free from build up of dirt and chaff which can restrict cooling ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG SL Select the oils SAE viscosity grade according to your expected operating temperature SAE VISCOSITY GRADES F 20 0 30 32 40 60 80 100 C 30 20 10 0 10 20 30 40 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart4_e FIG 13 Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year Check the crankcase oil level before starting the engine and after each eight 8 hours of operation TO CHANGE ENGINE OIL See Figs 13 and 14 Determine temperature range expected before oil change All oil must meet API service classification SG SL e Be sure tractor is on level surface e Oil will drain more freely when warm e Catch oil in a suitable container e Remove oil fill cap dipstick Be careful not to allow dirt to enter the engine when changing oil e Remove yellow cap from end of drain valve and install the drain tube onto the fitting OIL DRAIN VALVE CLOSED AND POSITION YELLOW CAP FIG 14 e Unlock drain valve by pushing inward and turning counterclockwise e To open p
42. t instructions in the Service and Adjustments section of this manual e Lubricate as shown in the Maintenance section of this manual e Be sure that all nuts bolts and screws are securely fastened Inspect moving parts for damage breakage and wear Replace if necessary e Touch up all rusted or chipped paint surfaces sand lightly before painting eal Fully charge the battery for storage e After a period of time in storage battery may require recharging e To help prevent corrosion and power leakage during long periods of storage battery cables should be dis connected and battery cleaned thoroughly see TO CLEAN BATTERY AND TERMINALS in the Mainte nance section of this manual e After cleaning leave cables disconnected and place cables where they cannot come in contact with battery terminals e If battery is removed from tractor for storage do not store battery directly on concrete or damp surfaces 24 ENGINE FUEL SYSTEM IMPORTANT IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR FUEL FILTER FUEL HOSE OR TANK DURING STORAGE ALSO EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS CALLED GASOHOL OR USING ETHANOLOR METHANOL CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE e Empty the fuel tank by starting the engine and let it run until the fu
43. ttachment while in reverse H LIGHT SWITCH Turns the headlights on and off J GEARSHIFT LEVER Selects the speed and direction of the tractor OPERATION The operation of any tractor can result in foreign objects thrown into the eyes which can result in severe eye damage Always wear safety glasses or eye shields while operating your tractor or WEAR YOUR FORESIGHT IS BETTER THAN NO SIGHT or standard safety glasses HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE See Fig 4 Your tractor is equipped with an operator presence sens ing switch When engine is running any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine e Depress clutch brake pedal B all the way down and hold e Pull parking brake lever C up and hold release pres sure from clutch brake pedal B then release parking brake lever Pedal should remain in brake position Make sure parking brake will hold tractor secure FIG 4 STOPPING See Figs 5 and 6 MOWER BLADES e To stop mower blades move attachment clutch clutch lever to disengaged position fn fn Disengaged Position f Attachment Clutch Engage Position FIG 5 11 performing any adjustments or repairs We recommend a wide vision safety mask over spectacles GROUND DRIVE e To stop ground drive depress clutch brake pedal all the way down e Move gear shift lever J to neutral position
44. turning counterclockwise e Install new blade with stamped THIS SIDE UP facing deck and mandrel assembly IMPORTANT To ensure proper assembly center hole in blade must align with star on mandrel assembly e Install and tighten blade bolt securely 45 55 Ft Lbs torque IMPORTANT Special blade bolt is heat treated MANDREL ASSEMBLY BLADE CENTER se BLADE BOLT SPECIAL gt FIG 12 BATTERY Your tractor has a battery charging system which is sufficient for normal use However periodic charging of the battery with an automotive charger will extend its life e Keep battery and terminals clean e Keep battery bolts tight e Keep small vent holes open e Recharge at 6 10 amperes for 1 hour NOTE The original equipment battery on your tractor is maintenance free Do not attempt to open or remove caps or covers Adding or checking level of electrolyte is not necessary TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to leak power e Disconnect BLACK battery cable first then RED bat tery cable and remove battery from tractor e Rinse the battery with plain water and dry MAINTENANCE e Clean terminals and battery cable ends with wire brush until bright e Coat terminals with grease or petroleum jelly e Reinstall battery See REPLACING BATTERY in the Service and Adjustment section of this manual V BELTS Check V belt
45. ull out on the drain valve e After oil has drained completely close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown e Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve e Refill engine with oil through oil fill dipstick tube Pour slowly Do not overfill For approximate capacity see PRODUCT SPECIFICATIONS section of this manual e Use gauge on oil fill cap dipstick for checking level For accurate reading insert dipstick into the tube and push down firmly into place before removing Keep oil up to but not over the FULL line on dipstick Push dipstick down firmly into the tube when finished CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers AIR FILTER Your engine will not run properly using a dirty air filter Service air cleaner more often under dusty conditions See Engine Manual ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year MUFFLER Inspect and replace corroded muffler and spark arrester if equipped as it could create a fire hazard and or dam age SPARK PLUGS Replace spark plugs at the beginning of each mowing sea son or after every 100 hours of use whic
46. under the machine Keep clear of the discharge opening at all times Only allow responsible adults who are familiar with the instructions to operate the machine Clear the area of objects such as rocks toys wire etc which could be picked up and thrown by the blades Be sure the area is clear of bystanders before operat ing Stop machine if anyone enters the area Never carry passengers Do not mow in reverse unless absolutely necessary Always look down and behind before and while back ing Never direct discharged material toward anyone Avoid discharging material against a wall or obstruction Ma terial may ricochet back toward the operator Stop the blades when crossing gravel surfaces TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH Do not operate machine withoutthe entire grass catcher discharge guard or other safety devices in place and working Slow down before turning Never leave a running machine unattended Always turn off blades set parking brake stop engine and remove keys before dismounting Disengage blades when not mowing Shut off engine and wait for all parts to come to a complete stop before cleaning the machine removing the grass catcher or unclogging the discharge guard Operate machine only in daylight or good artificial light Do not operate the machine while under the influence of alcohol or drugs Watch for traffic when operating near or
47. us injury or HOT SURFACES indicates a hazard which death The safety alert symbol Machi if not avoided could result in death serious injury is used to identify safety inform ASP PPIGPE RM Gamage ation about hazards which can result in death serious injury and or property damage Mf FIRE indicates a hazard which if not avoided could result in death serious injury and or property damage y OPERATION KNOW YOUR TRACTOR READ THIS OWNER S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments Save this manual for future reference FIG 3 Our tractors conform to the applicable safety standards of the American National Standards Institute A ATTACHMENT LIFT LEVER Used to raise lower and adjust the mower deck or other attachments mounted to your tractor B CLUTCH BRAKE PEDAL Used for declutching and braking the tractor and starting the engine C PARKING BRAKE Locks clutch brake pedal into the brake position D THROTTLE CHOKE CONTROL Used for starting and controlling engine speed E ATTACHMENT CLUTCH LEVER Used to engage the mower blades or other attachments mounted to your tractor 10 F IGNITION SWITCH Used for starting and stopping the engine G REVERSE OPERATION SYSTEM ROS ON POSI TION Allows operation of mower deck or other powered a
Download Pdf Manuals
Related Search