Kenwood DDX6036 Car Video System User Manual
Contents
1. Visual input iPod AV Input 2 switchable Resistance free mini plug 3 5 6 DDX6036 DDX6036M Audio Visual Output Visual output Yellow Audio left output White Audio right output Red Audio Visual input Visual input Yellow Audio left input White Audio right input Red Rear View Camera Input Visual input Yellow Front Preout Audio left output White Audio right output Red Rear Preout Audio left output White Audio right output Red Subwoofer Preout Audio left output White Audio right output Red Optional Accessory Connection iPod commercially available KCA iP301V Optional Accessory Visual Output Yellow Audio Output Black USB terminal USB terminal E mp ET Connection cable Included in the KCA BT200 KCA BT200 Optional Accessory Navigation System Optional Accessory TV Tuner Optional Accessory Connection cable Included in the Navigation System E Navigation units that can be connected to this unit As of December 2009 KNA G630 LE KNA G630CN Connection cable For latest information access the Included in the TV tuner www kenwood com cs ce English 7 Installing the Escutcheon For Genera2. frame can be removed from the top side in the same manner 2 When the lower level is removed remove the upper two locations 10 DDX6036 DDX6036M Removing the Unit 1 Remove the hard rubber frame by referring to the removal procedure in the section lt Removing the Hard Rubber Frame gt 2 Insert the two removal tools 4 deeply into the slots on each side as shown Accessory 4 3 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 4 Pull the unit all the way out with your hands being careful not to drop it KENWOOD
3. in malfunction Do not press hard on the panel surface when installing the unit to the vehicle Otherwise scars damage or failure may result English 3 Connection If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box Ignition key switch B A de Ignition wire Red Car fuse box Car fuse box B Main fuse Battery wire Yellow mp L FM AM antenna input Ground wire Black Antenna Cord To car chassis Ce Battery E Connect to the vehicle s parking brake detection switch harness Parking sensor wire Light Green lt 4 PRK SW For the sake of safety be sure to connect the parking sensor Connect to vehicle s reverse lamp harness when Reverse sensor wire Purple White using the optional rear view camera Steering remote control input Light Blue Yellow To steering remote A To use the steering wheel remote control feature you need to an exclusive remote adapter not supplied matches your car is required When this terminal is not in use leave its cap on Dimmer control wire Orange White To car light control swit
4. KENWOOD MONITOR WITH DVD RECEIVER DDX6036 DDX6036M INSTALLATION MANUAL Kenwood Corporation B54 4756 00 MW M2W Accessories 2 DDX6036 DDX6036M Installation Procedure 1 To prevent a short circuit remove the key from the ignition and disconnect the O battery 2 Make the proper input and output wire connections for each unit w Connect the speaker wires of the wiring harness Connect the wiring harness wires in the following order ground battery ignition Connect the wiring harness connector to the unit Install the unit in your car Reconnect the battery Press the reset button Perform the Initial Setup Refer to the Instruction Manual gt o o wu U A WARNING If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box Do not cut out the fuse from the ignition wire red and the battery wire yellow The power supply must be connected to the wires via the fuse NCAUTION Install this unit in the console of your vehicle Do not touch the metal part of this unit during and shortly after the use of the unit Metal part such as the heat sink and enclosure become hot About the Front Panel When removing the produc
5. ch Connect to the terminal that is grounded when either Mute wire Brown the telephone rings or during conversation E To connect the Kenwood navigation system consult your navigation manual Depending on what antenna you are using Motor antenna control wire Blue connect either to the control terminal of the motor antenna or to the _ power terminal for the booster amplifier of the film type antenna When using the optional power amplifier Power control wire Blue White connect to its power control terminal If no connections are made do not let the cable come out from the tab 4 DDX6036 DDX6036M Cooling fan FUSE 15 Accessory 1 REVERSE recon ite Black e To front left speaker White Gray Blac ILLUMI e HI To front right speaker Gray UTE Green Blacl o e HT To rear left speaker Green Purple Blac e HU To rear right speaker ANT CONT Purple P CONT English 5 System Connection USB terminal USB device lt lt IN commercially available Audio input iPod AV Input 2 switchable Resistance free stereo type mini plug 3 5
6. l Motors 1 Cut out accessory 8 to meet the shape of the opening of the center console 2 Attach accessory to the unit Cut out to meet the shape of the opening in the vehicle Accessory 5 For Volkswagen 1 Attach accessory 8 to the unit Accessory 9 8 DDX6036 DDX6036M For Toyota Scion Cut out accessory 5 as illustrated Cutting line Accessory 2 Fold double sided adhesive accessory along the slit and attach it to accessory cut out against the center rib as illustrated Use 2 pieces of accessory for 1 accessory 5 cut out 3 Attach accessory 5 cut out to the unit Accessory 7 f Y f 7 f Y f 4 Installation for Monitor Player Unit Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place E Make sure that the unit is installed securely in place If the unit is unstable it may malfunction eg the sound may skip Installation on Toyota Nissan or Mitsubishi Car using Brackets Accessory G M5x6mm or Accessory 8 M5x7mm Car Bracket Accessory G M5x6mm or Accessory 8 M5x7mm English 9 Removing Monitor Player Unit Removing the Hard Rubber Frame escutcheon 1 Engage the catch pins on the removal tool 4 and remove the two locks on the lower level Lower the frame and pull it forward as shown in the figure Accessory The
7. t from the box or installing it the front panel may be positioned at the angle shown in Fig 1 This is due to the characteristics of a mechanism the product is eguipped with If the program that is activated when the product is first powered on works properly the front panel will automatically move into the position initial setting angle shown in Fig 2 Fig 1 Fig 2 After the Installation After the installation perform the lt Initial Setup gt Refer to the Instruction Manual by referring to the instruction manual A ounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals ake sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not use your own screws Use only the screws provided you use the wrong screws you could damage the unit the power is not turned ON PROTECT is displayed the speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may ave been activated Therefore the speaker wire should be checked your car s ignition does not have an ACC position connect the ignition wires to a power source that can be turned on and off with the ignition key If you connect the ignition wire to a power so
8. urce with a constant voltage supply as with battery wires the battery may die the console has a lid make sure to install the unit so that the faceplate will not hit the lid when closing and opening If the fuse blows first make sure the wires aren t touching to cause a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car When only two speakers are being connected to the system connect the connectors either to both the front output terminals or to both the rear output terminals do not mix front and rear For example if you connect the connector of the left speaker to a front output terminal do not connect the connector to a rear output terminal After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less This unit has the cooling fan page 5 to decrease the internal temperature Do not mount the unit in a place where the cooling fan of the unit are blocked Blocking these openings will inhibit the cooling of the internal temperature and result
Download Pdf Manuals
Related Search