Home

Kathrein CAP 700 Turntable User Manual

1. You can correct the inclination and horizontal angle of the antenna using the Elevation and Azimuth settings To do this press the GP buttons or enter a numeric value using the numeric keys and confirm with the ok button Check your settings by referring to the Signal Strength and Signal Quality bars on the right hand side The higher the bar the stronger and better quality the signal received The new co ordinates are not assigned to the satellite until you have saved the satellite position when exiting the Antenna Configuration menu When you have performed the correction press the button to exit the menu You will be asked whether you wish to save the changes Press one of the DO buttons Yes save changes or No don t save changes and confirm by pressing the button 49 CHANNEL SATELLITE SELECTION 9 By pressing the 5 buttons all channels can be selected in the sequence that they appear in the current TV R channel list and its sorting Press the lu blue button to switch between TV and radio channels CHANNEL SELECTION FROM THE CHANNEL LIST Providing you are not in a menu pressing the button calls up the channel list The following display appears Wednesday 20 12 2006 10 46 H l Also pay attention to the bars at the bottom of the on screen display These provide information on what to do next When you open this list the channel list selection
2. 291 Chemical Stability Sikaflex 291 is resistant to fresh water and salt water hard water and effluent from public drains including aqueous surfactants dilute alkalis and acids short term resistant to fuels mineral oils including vegetab le and animal oils and greases not resistant to organic acids alcohol stronger mineral acids and alkalis or solvents This information is intended only as a general indication Advice for specific applications is available on request Processing instructions Substrate preparation The surfaces to be bonded must be clean dry and free of dust and gre ase Data on preparation of materials surfaces can be found in the primer table for Sikaflex marine systems Processing Break the cartridge membrane and fully open it Insert the bag into the application gun and cut off the clip Cut off the tip of the nozzle to suit the crack to be filled and apply the sealant with a suitable manual bat tery powered or compressed air piston gun into the crack leaving no air bubbles Opened containers must be used up within a few days The processing temperature must not be below 5 C or above 40 C The opti mum temperature both material and sealant is beween 15 C and 25 C Additional information www sika com Sika Deutschland GmbH Stuttgarter Strasse 139 D 72574 Bad Urach Germany Tel 49 7125 940 761 Fax 49 7125 940 763 Kleb und Dichtstoffe Industrie For advice on
3. Place the turntable on prepared wooden supports to protect the roof of the vehicle 17 Avoid skin contact Arrow in the direction of travel Mark out the six holes for securing the mounting plate Place mounting plate on roof gland and secure with appropriate screws choose screws according to thickness structure of roof Apply Sikaflex 291 adhesive in a sinuous line between the two grooves and spread with spatula or similar Avoid skin contact Screw turntable on to mounting plate using torque wrench Caution Tightening torque 6 Nm Set up electrical connections Connect the UFS 740 receiver Connect the turntable to the battery driving 18 The antenna must always be lowered into horizontal position park position while Maximum driving speed of the vehicle 130 km h INSTALLATION AND CONNECTION INSTALLATION OF THE UFS 740SW RECEIVER The turntable is controlled by the UFS 740sw DVB S receiver The cable lengths must be taken into account when choosing the installation location For suspended installation use the installation kit supplied with the receiver Note When choosing the installation location bear in mind that the on off switch and the slots for inserting common interface modules should always be accessible The UFS 740sw is equipped with a power saving circuit and a separate infrared transmitter which means that the unit does not need to be placed where it is visible You can there
4. 0L 6 G v Z L 9 e LL abaAJON ABMION UBGBAUON Seq sAegq4 se vc Z 01 8 S L y 9 g y 0L GZ spue 1jeujeN epuepepelN Ze v 9L L 6 0 9 6 G L L amp E o9eUOyy o9euoyy oseuoy 92 0 Z L 6 9 L 9 8 Yy LL 9z Binogqwexn1 64anquwexn1 61nquwexn1 ute sus yooN LE v 9L L 0L g 0 9 a 0L 92 ureysuejuoerq ureisueju er 9 LUES 02 LI 0L L v L v G pz 9180J eH8042 U9801 SI 21 0 E 9 LL l GL GE el E Oc SpDUEUL 7 puejoujy puep LE OL 2z GL GL 9 L y L 0L GC se W Apey uarey ouGelo1g apue15 e1 AL 6 Z li 6 D l 8 S 92 ureyug 1eo49 ueruue uqgo45 9r ZZIVE Ze 82 L 81 ti LL A Z LZ 0JQ15 999915 pue USyYJBUS c GL vi ef 6 4 9 S 0L 9 ie epuejurJ puejurJ pue uur4 Li Z 01 L G L OL CL 6 94 ZE SIUB14 9IUBA4 YI BJYUBIY 82 e vl ZI 6 0 y 0 jis Ez euDeuie v Aueuue5 pue uosineq v2 WEL LL 8 L L e y 6L yrewoueq yewuoq yewoueq Lv GL LE 62 Sc 6L 9L CL d ti V ups euebing euebing ueueb ng Gc Z 01 8 V Z G Z 6 G LL ZZ enbibjeg e uniDjeg ueibjeg Ly 91 82 92 Ge SI LL 8 G 8 e Ez glueqiy elueqiy uaiueqy sononsem TT DT asenonsem sgaseg s3nse3 Isansea is3nseg ISOM ISOM W ei ISO ISO n ISO uen ISO s3Ase3 o0 qz wosejeL oS on ol OL Min EI FEL oZ 8Z ISO oth sKeg Anuno9 pue GL OL ZZ pala pig ez JOUL VEM LM duialoH ZM VHLSV L paiqoung LVSYUNL jesedsiH onueny onuenv 1vs1aina i1vsTaina 1vsT1ain3a VHLSV Solle eege ueuleiee N CN POLARISATION
5. GEL O0S Oz e6ues Guidwejo LEE pueb jooy ejejd Bununoyy u ee es un 2474 i ii o S sixe Ale oy me S EL oGZ XBW UOUEAGI o Gy uonNeng g Y Y L61 m 33 TECHNICAL DATA Type CAP 700 Order no 20310019 LNB 1 output switchable V H 14 18 V low high 0 22 kHz LNB supply voltage V vertical 11 5 14 horizontal 16 19 Input frequency GHz 10 70 12 75 Output frequency MHz 950 1950 1100 2150 Oscillator frequency L O GHz 9 75 10 60 System quality G T 11 3 12 5 GHz dB K 13 4 13 7 Power supply vehicle battery V 10 9 13 8 Power consumption from the 12 V vehicle electrical system Inrush current Type 10 max 12 Satellite search A Type 3 TV reception Type 1 2 Stand by Type 0 024 Current consumption from the receiver mA Type 160 Setting range Elevation o 0 75 Azimuth 370 Skew 45 Weight of the turntable with parabolic reflector Kg 9 7 Packing unit weight pc kg 1 15 3 Ignition signal 12 24 V Search time for first satellite typ 10 120 s Search time for further satellites typ 2 30 s LSM search time 2 158 LSM Last Satellite Memory 34 SIKAFLEX 291 SAFETY DATA SHEET 1 Materials preparation and company designation Data on the product trade name Sikaflex 291 Data on manufacturer suppliers Manufacturer suppliers Sika Deutschland G
6. attachment on the underside of the respective mounting piece 2 pieces Vertically insert each mounting piece into the fifth slot from the edge as shown in Fig 1 Then push each mounting piece downwards and outwards see Fig 2 until they lie flat on the receiver casing see Fig 3 Now press the mounting pieces firmly against the receiver casing at the points shown arrowed in Fig 3 until the catch audibly snaps home in the receiver casing Now hold the receiver with the installation kit attached at the installation location Screw in the wood screws supplied through the smaller holes in the screw attachment area 4 x see Fig 4 Wherever possible use the wood screws supplied If these are unsuitable other screws of adequate size and strength can be used Under no circumstances however use countersunk wood screws since these can damage the attachment area see Fig 5 Then screw all four screws fully home so that the installation kit is no longer able to come free INSTALLATION ON A FIXED FLAT SURFACE So as to prevent the receiver slipping or falling the mounting kit can also be attached to the underside of the receiver Assembly is the same as for suspended installation except that the installation kit is hooked into the underside of the receiver 20 INSTALLATION AND CONNECTION LAYING CABLES AND CONNECTING THE TURNTABLE Lay the coaxial cable to the UFS 740sw e Lay the turntable power suppl
7. factor of at least 75 dB If you tied the cables together with wire or similar materials remove this to prevent the risk of fire When connecting the power cables receiver and turntable to the vehicle electrical supply make sure that the cable polarity is not reversed If the cable polarity is reversed there is a risk of thermal overload and damage to components when the equipment is powered up Power supply fusing Operate the system from your vehicle s battery 12 V or a suitable mains power supply unit This power supply unit must ensure a stable output voltage of 12 V continuous current of 11 A and 15 A 300 ms surge current The peak current consumption is up to a maximum of 12 A To ensure reliable functioning of the connection control unit the power supply cable must be connected directly to the battery If the supply voltage is too low the UFS 740sw receiver indicates this with the on screen message On board voltage too low on the television screen A 15 A fuse is incorporated in the power supply cable If the fuse blows rectify the source of the fault and replace the blown fuse with a fuse of the same rating 15 A Never remove or bypass the fuse in the cable cable fire hazard Connecting the power supply cable lead marked Ignition activates the turntable function for automatic lowering of the antenna This lowering takes place as soon as the vehicle ignition circuit is turned on When connecting
8. into account the increase 79 cm in the vehicle height is an option and is preferable to manual lowering Users unfamiliar with the necessary repair work are urged not to attempt to lower the antenna manually into park position themselves They should contact a technician or engineer They may find a suitable person on the campsite In any case the safety instructions listed below must be followed SAFETY NOTES CO ef e A 4 Make sure that The antenna and connected units are disconnected from the power The person carrying out the repairs does not suffer from vertigo and can move around safely on the roof of the caravan or motor home The person carrying out the repairs is wearing sturdy and non slip shoes The person carrying out the repairs has a secure position to stand and hold on while working The roof and the climbing equipment used e g ladder are dry clean and non slip The roof can withstand the weight of the person carrying out the repairs Attention Risk of death or injury due to falling or roof collapsing Do not hold onto the antenna as the rocker comes free without warning during dismantling Attention Risk of death and injury due to falling or crushing Nobody should be inside the caravan motor home underneath the antenna during dismantling installation Attention Risk of death or injury due to possible roof collapsing and falling parts MANUAL LOWERING TO PARK POSITION MANUAL LOWER
9. is poor ABEK multi range filter The gas filter class is dependent on the local concentration of injurious substances Hand protection Wear butyl rubber nitrile rubber gloves Eye protection Safety glasses Body protection Work clothing 9 Physical and chemical characteristics Appearance Form Colour Smell Safety relevant data methods Flashpoint Density at 20 C Solubility in water Viscosity at 20 C VOC solvents VOC CH 10 Stability and reactivity pasty various depends on the pigment characteristic gt 65 C approx 1 26 g cm reacts with water not applicable 3 47 3 47 96 Substances to be avoided hazardous reactions No hazardous reactions if correctly stored and handled Thermal decomposition and hazardous products of decomposition No decomposition if used correctly Markings in the left margin indicate revisions from the previous version 0 05 mg m 0 005 ml m 440 mg m 100 ml m 221 mg m 50 ml m 442 mg m 100 ml m TRGS 900 DE 2004 TRGS 900 DE 2004 TRGS 900 DE 2004 TRGS 900 DE 2004 2000 39 EC 2000 39 EC 2000 39 EC 2000 39 EC 37 SIKAFLEX 291 SAFETY DATA SHEET 11 Toxicology data Sensitisation Sensitisation allergic reactions may occur Sensitive individuals may exhibit allergic reactions even at very low concentrations Experience of human exposure On skin contact May lead to irritation On eye contact May lead to irritation On being bre
10. operating manual for the CAP 700 lf despite studying this operating manual you still have questions about getting started with the unit or using it correctly or if unexpected problems occur please contact your specialist dealer The Kathrein customer hotline is also at your disposal Phone 49 8031 184 700 The automatic updating of the EPG data described in the UFS 740sw operating manual as occurring at 03 00 in the morning is not performed automatically when the UFS 740sw is being operated on the CAP 700 The EPG data are updated when an individual channel is viewed At this point however the receiver updates all EPG data for the channels that are broadcast from the currently selected receiving transponder For example You have selected the channel SAT 1 At this point for instance the EPG data will be updated for ProSieben and KABEL1 42 IMPORTANT INFORMATION FOR CAP 700 BEFORE SETUP This section of the UFS 740 operating manual for the turntable assumes that the UFS 740 and the turntable have been properly installed and connected as described in the installation and operating manuals If you have not yet done so read the safety instructions at the beginning of the UFS 740sw operating manual and follow them when handling the UFS 740sw and the turntable Before setting up your satellite system make sure that the location allows a free view to the satellite positions to the South and is not shadowed by
11. search is started when you select a channel lf the turntable has not yet saved the position of the satellite you will see the following display when you select a channel example If the vehicle is not on supports during the search process and people are mo ving around inside it there is a risk that movement of the vehicle will mean that the satellite is not found le Eeer gt HANKAN La wn Press the OK button to start search mode The search may take a few minutes generally about two minutes You will first see the following message W E WT UR EEN E W mim ll LA ctra AG DO eceooareh cofsrt ar Astra 13 7 search started ba As soon as the turntable has found the correct satellite it saves this position During this process you receive no TV picture The turntable will then perform an automatic fine adjustment if the signal level is sufficient the satellite position will be saved immediately by the turntable During the fine adjustment you will for the first time receive a TV picture this however can still freeze during the fine adjustment process whether it does or not is system dependent The set position of the satellite that was found is saved and the desired channel appears on the TV screen 48 Press the a button to return to the main menu The DO buttons and button allow you to call up the submenus Settings Antenna Configuration Thursday 21 12 2006 OE Ty MINU
12. selection and arran gement of a suitable pump system please contact the System Enginee ring Department at Sika Industry Smoothing off Smoothing off must be performed within the skin formation time of the adhesive We recommend Sika N smoothing off agent Other smoothing off agents should be checked for sui tability before use Removal Uncured Sikaflex 291 can be remo ved from equipment and tools with Sika Remover 208 Cured material can only be removed machanically Hands skin should be cleaned im mediately with Sika Handclean or a suitable hand cleansing paste and water Do not use solvents Painting over After the skin has formed Sikaflex 291 can be painted over The suitab lility for painting over must be trialled prior to application Powder coating points may be applied only to fully cured Sikaflex 291 It should be borne in mind that the hardness and film thickness of the paint finish may affect the expansion of the plastic and lead to cracking Internet www sika industry de e mail industry de sika com Additional information The following documents are availa ble on request Safety data sheet Primer table for systems General guidelines for working with Sikaflex adhesives and sealants Marine handbook Sika marine Containers Tube 100 ml Cartridge 310 ml Bag 400 ml Important When handling our products please read the material specific safety da
13. the centre position makes sense only if a satellite to the far West or the far East is actually preferred for reception The respective setting angle required for the polarisation can be found in the following table a ea West nn East Kop io T 20 A Longitude for the reception position 26 sDumes uonesuejog pue uONBAJIF YINWIZY UONBLOJU ED1UYD9 Aueuudinboe UONA9J94 alijjalesS Woy nuou Wiy Xopui BS ap aP UI9JYIEYX MMA Japun abeg euioH UISIUIEN 34 uo 1euJ9 u ayi uo PUNOJ aq ueo Saujunoo asauy ui SUMO pue Saujunoo 1oy1O Ge LUES L 81 LL 6 9 L L OZ eubuoy e7 Are uny ule un enbouoj enbijqndoy Le LZIGL 91 El L S e 0 v y LZ Pqnd y u2ezo ueiuoeuos 62 G 9 8 Z LL GL 8L LZ ile YZ Ot oubedsq j ureds ueiueds ve 6 12 81 GI 8 S e L G pZ eluano S BIUaAO S UaIUBMOIS ve Dez 02 LI LL 8 9 L 0 8L einbeaojs enjeAolS Ioxemojs oJ6ouUJ UO WN 91q 9s 0146auajuoN 6 t 1 92 v2 L ti LL 8 S 6 L LZ pue eiq1as 0 6ous juoN usiquas 0 SIGL zl 8 L ES G iE LL 82 essing puepeziMS ziaMmuog L WEL LL 6 S v e L 9 L e epens uapems uopamyos 8 91 82 92 c LI Vi LL 6 L v 94 oiuewnoy eluewoy uoIUEWNY v2 21 0 8 AL 02 Ez 92 ZZ 8z v peBnyog jeBnyog je6ny0q LE 8 02 81 SI 6 4 S e L 0 Die eufojog puejog uejod Ze 9 81 91 L 9 0 Z e 9 pZ eyouny eu18ny y019 19 SQ SL 0 21
14. the control unit to the vehicle power supply make sure that the 12V Earth and Ignition wires cannot be disconnected by intermediate switches as this could deactivate the automatic lowering function SAFETY INSTRUCTIONS IMPORTANT NOTES The antenna will be lowered within 12 seconds of the ignition being switched on if the unit is in stand by mode or the UFS 740sw is switched off Otherwise the control unit that is in use is lowered immediately Important Lowering the antenna can take up to 30 seconds after the ignition is switched on Checks before commencing a journey e Before commencing a journey the antenna must always be lowered into horizontal position park position If the antenna has collided with a fixed or movable object check that it is still securely attached e As the antenna is subjected to vibration loads during driving you should check at regular intervals depending on the frequency of driving that the system is still securely attached and tighten any parts that have worked loose e The maximum permissible speed for vehicles with a receiver unit mounted on the roof and the antenna lowered is 130 km h e Lower the antenna if it will not be used for a long period This makes the securing bolts more difficult to access protection against theft Antenna in the park position whilst driving The antenna must always be lowered into horizontal position park position while driving N As a remind
15. through holes on the turntable must be perfectly aligned with the threaded holes on the mounting plate When lowering make sure that the cables are fed through the cable gland and are not crushed e Apply a little adhesive sealant to the six threaded holes in the mounting plate and screw the fastening screws into the thread Tighten the screws to a torque of 6 Nm e To prevent water vapour from inside the vehicle reaching the turntable through the roof gland thread the two cables through the sealing gasket supplied see Fig E and insert this into the roof gland until it reaches the stop Insert the plug into the third cable duct which is not used Make sure that no tensile load is acting downwards on the sealing gasket as this can cause it to fall out in the course of time 15 INSTALLATION AND CONNECTION VERSION WITH EXTERNAL CABLE GLAND FIG F 16 Direction of travel l an Nez C D Baseng 1 Cables laid in the cable duct and water tight roof gland Not supplied The HDZ 100 roof gland is available as an accessory under part number 20410032 from specialist dealers The external roof gland is arranged so that it forms a water tight enclosure on the vehicle roof around the point where the two cables projecting from the turntable are connected to the two extension cables within the interior of the vehicle and where if necessary they can be disconnected Arrange the cables in th
16. vehicle can remain there Unscrew the six M6 screws securing the turntable to the mounting plate e Place two wooden supports on the vehicle roof for protection e Then place the turntable on the prepared wooden supports e To ship the turntable use the original packaging which you have saved e Seal the opening in the vehicle roof appropriately to protect against the ingress of moisture e f a HDZ 100 roof gland has been fitted and the equipment is then removed the cable channels no longer used should be sealed with the integral plugs The enclosure is then watertight once again Note Before exchanging the UFS 740sw first move the turntable to the park position ADDRESS OF THE SERVICE CENTRE ESC Electronic Service Chiemgau GmbH Bahnhofstra e 108 83224 Grassau Germany Phone 49 8641 9545 0 Fax 49 8641 9545 35 and 36 Internet http www esc kathrein de e Mail service esc kathrein de 25 POLARISATION SETTING POLARISATION SETTING The LNB for the CAP 700 is factory set to the polarisation setting O In this position you can still receive signals from satellites with differences between the longitude of the desired reception area and the orbit position of the satellite of 15 to 20 For differences greater than this it is best to rotate the LNB and set the necessary polarisation angle However we expressiy draw attention to the fact that positioning the LNB at a deviation of up to 45 or up to 45 from
17. 2 2006 10 52 E T e MENU Use the DO buttons to navigate to the sub item Reset the turn table antenna and then press the OK button The following display appears Press the OK button to acknowledge the displayed message The antenna is reset and automatically moves to park position A further short message Park position reached appears Press the button to exit the menu Note Before exchanging any component of the system such as the receiver the turntable should be moved to its park position by means of the Reset the turn table antenna command The Reset deletes all previously saved satellite positions The satellite data in the UFS 740 receiver are however retained 52 RESET PARKING PARKING THE TURNTABLE You have three options for parking the antenna 1 The antenna can be moved to park position by pressing the button twice 2 Press the a button to return to the main menu The Ge buttons and button allow you to call up the submenus Settings Antenna Configuration Use the DO buttons to navigate to the sub item Move to park position Now press to park the antenna 3 When the ignition is operated the antenna automatically moves to the park position However for this to happen the green wire of the power supply cable must be connected to the ignition and the turntable connected to the power supply see Connection Diagram Refer to the detailed inst
18. HE INTENDED PURPOSE The MobiSet 3 digital CAP 700 is designed to receive digital TV and radio programs via satellite The automatic positioner is intended to be used as a turntable for the parabolic reflector The turntable can be used to receive digital TV and radio signals in the frequency range from 10 70 to 12 75 GHz the antenna cannot receive terrestrial signals e g DVB T The turntable can only be used in conjunction with the UFS 740sw DVB S receiver In conjunction with this receiver the turntable provides fully automatic alignment of the parabolic reflector to receive digital satellite signals The turntable is designed for use on stationary caravans or motor homes Any use other than that specified above will void the warranty or guarantee The following circumstances result in the loss of all warranty and liability claims towards the manufacturer e Improper installation e Use of non specified mounting materials which cannot guarantee the mechanical reliability of the antenna system e Impermissible use e g use of the satellite dish for storage e Structural changes or interference with the components and mounting accessories in the set which could endanger both the mechanical and functional reliability e Improper or forcible opening of the components e Use of cleaners containing solvents such as acetone nitro cellulose thinners petrol etc e Failure to observe installation and safety instructions in this manual No
19. ING In the centre of the antenna arrowed there is a plastic cap Lever this off with a narrow slot head screwdriver Behind the cap is an M8 hexagon head screw Unscrew these using a 13 mm socket wrench After removing the M8 screw a further thread can be seen 3 di 8 Attention Secure and support the antenna to prevent it tipping over The connection to the rocker can suddenly come loose during the next step item 4 It is then no longer connected to the turntable Screw an M10 x 40 screw into this thread minimum length 40 mm Screwing in the M10 screw pushes the rocker off the tapered shaft and releases the engagement Important Screw the screw in only as far as necessary to free the rocker from engagement on the tapered shaft Tilt the antenna into the park position horizontal position Unscrew the M10 screw This allows the rocker to re engage on the tapered shaft Replace the M8 screw and tighten it Replace the plastic cap Loosening the rocker from the taper shaft causes the rocker zero point position to be lost When the authorised dealer rectifies the defect he will recalibrate the rocker 9 Consult an authorised dealer 31 TECHNICAL DATA DIMENSIONS MM Direction of travel a 1833 118 3 282 193 8 32 TECHNICAL DATA pati 602 ejejd Gununouu Buipnjour CAE S
20. Installation and operating manual Mobiset 3 digital CAP 700 KATHREIN Antennen Electronic CONTENTS BONTENTS X X 6 6 2 FOREIGN LANGUAGE INSTALLATION MANUALS DISPOSAL e eee 3 MOBISET 3 CAP 700 COMPONENTS SCOPE OF DELIVERY eee erre nennen 4 PO Lado cA ND Eee ae Dauer ern Dana ea TREE ee Re 5 SAFETY INSTRUCTIONS IMPORTANT NOTES an nn nun an nn nun ENEE ENEE EE REENEN EE en 6 INSTALLATION AND CONNECTION u un een 9 INSTALLATION OF CABLE GLAND AND MOUNTING PLATEN 11 INSTALLATION OF TURNTABLE eege 14 BRIEF INSTRUCTIONS FOR INSTALLING THE TURNTABLE nnne 17 INSTALLATION OF THE UFS 740SW DECEIWER nnne nnn nnn 19 LAYING CABLES AND CONNECTING THE TURNTABLE enne 21 CONNECTING TO en TT 21 FUNCTIONAL INSTRUCTIONS FOR CONNECTION TO THE ON BOARD POWER SUPbUN 22 CONNECTION EXAMPLE FOR 12 V BATTERY CONNECTION een 23 RECEPTION RANGE FOOTPRINT sn aaa 24 DISMANTLING FOR SERVICING sss ssssssssessessssssesessesessssesessesssesacsssatscsesacsesaesesesanseeaeacseeaeees 25 BESCH H EI CIE sante diya ee sitan ee tee ole oo nee ra a 25 ADDRESS OF THE SERVICE CENTRE EE 25 POLARISATION SETTING cccssssscssssesesessssscscecscesevvsesesecececevavavausesesesesesevavavacsesesecesevavavarseeeesns 26 POLARISATION SETTING esse ee e
21. OSAL Dear Customer Ch re Cliente Cher Client Gentile cliente Estimado cliente GB You can obtain an English version of our mounting instructions from our representatives in your country http www kathrein de include kontakte groups eng cfm kontinent 18gruppe SAT or download one from our homepage http www kathrein de en sat products englisch htm F Vous pouvez obtenir un manuel d installation en francais chez notre r pr sentant en votre pays http www kathrein de include kontakte groups eng cfm kontinent 18gruppe SAT ou le telecharger de notre page d ouverture http www kathrein de en sat products franzoesisch htm Lei puo avvere la versione italiana delle istruzioni di montaggio dalla nostra rapresentanza http www kathrein de include kontakte groups eng cfm kontinent 18gruppe SAT piu vicina della sua citta oppure scaricarla dalla nostra hompage http www kathrein de en sat products italienisch htm E Para obtener la versi n espanola de nuestro manual de instalaci n contacte nuestros representantes en su pa s http www kathrein de include kontakte groups eng cfm kontinent 1 amp gruppe SAT o bajela de nuestra p gina de Internet http www kathrein de en sat products spanisch htm DISPOSAL INSTRUCTIONS Electronic equipment is not domestic waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27 January 2003 concerning used electrical and electronic appli
22. PERATIONS The explanation for this setting procedure is based on the assumption that the entire CAP unit has been properly put together installed and set up as described in this installation manual The safety instructions in the detailed operating manual for the UFS 740sw must also be fol lowed The key names refer to the remote control for the UFS 740sw receiver a 28 Turn on the receiver at the main switch on the front of the unit Press any of the numeric buttons to bring the receiver into operating mode If necessary first perform a first installation Wait until the message Position of Astra is not known Start search is displayed cancel this procedure by pressing the button Next press the a button to go to the main menu and use the WG buttons to move to the Settings menu item Confirm the selection by pressing the button Use the 9 buttons to move to the Antenna Configuration menu item Confirm the selection by pressing the button Use the WG buttons to select the Elevation option and use the number keys on the remote control to enter 400 8 9 POLARISATION SETTING Press the button and the turntable will move to the selected elevation angle Turn off the UFS 740 using the main switch on the front and disconnect it from the power 10 Use the socket driver supplied size 20 to slacken the securing screw of the clamp on the LNB 11 17 18 Rotate the LNB by the requi
23. SETTING SAFETY NOTES We strongly advise that users who are not familiar with the setting operations should not undertake to set the LNB themselves They should contact a technician or engineer They may find a suitable person on the campsite Make sure that The antenna and connected units are disconnected from the power The person carrying out the installation does not suffer from vertigo and can move around safely on the roof of the caravan or motor home The person carrying out the settings is wearing sturdy and non slip shoes The person carrying out the settings has a secure position to stand and hold on while working The roof and the climbing equipment used e g ladder are dry clean and non slip The roof can withstand the weight of the person carrying out the settings Attention Risk of death or injury due to falling or roof collapsing During setting operations make sure that no persons in particular no children are in the immediate vicinity of the turntable and that they cannot touch any moving parts crush hazard Nobody should be below the antenna inside the caravan motor home during setting operations Attention Risk of death or injury due to possible roof collapsing and falling parts on the motor home caravan Continue to refer to the Safety instructions important information section No obstructions may be present in the turning range see Safety instructions and important information SETTING O
24. al luminance chrominance Press the lu green button to move to the next menu The following display appears System PIP Use the oo buttons at System to select CAP Then press the KN green button to move to the next menu 46 The following display appears Local time offset Use the oo buttons to set the time zone variation from UTC formerly GMT e g for Germany 1 hour Use the DO buttons to switch to the Automatic clock change field Use the oo buttons to select whether the receiver should automatically change over between summer and winter time If On is selected the receiver automatically sets itself to the right time If Off is selected the field for manual selection of summer and winter time is displayed below Press the Colle buttons to perform the setting Press the KN green button to close first installation and return to the main menu Press the button to view the TV picture Note Channel search Item 6 6 is skipped if CAP is set since the antenna must first be aligned to the desired satellite before a channel search can be started 47 ALIGNMENT SATELLITE SEARCH The antenna is aligned automatically After the UFS 740 has been switched on the turntable automatically moves to the last channel received and the associated satellite position e g ARD ASTRA This works because each satellite is automatically recognised by the turntable The satellite
25. ances it must be disposed of properly At the end of its service life take this unit for disposal to an appropriate official collection point Do not throw spent batteries into your domestic waste take them to a collection point for CAY Spent batteries are special waste ae spent batteries MOBISET 3 CAP 700 COMPONENTS SCOPE OF DELIVERY 1 Roof gland with retaining nut 2 Mounting plate 3 Turntable with integral controls 4 Antenna carrier 5 Parabolic reflector 6 LNB UFS 740sw d Front view See UFS 740sw operating manual for a rear view of o Enn the receiver together with explanation of functions and ee operating instructions PRODUCT PACKAGE The MobiSet 3 digital CAP 700 consists of Turntable complete with control electronics pre assembled parabolic reflector with LNB Mounting plate Complete cabling set 1 x coax cable 8 m long and one power supply cable 10 m for connection to the on board power supply Roof gland with sealing gasket Sikaflex 291 adhesive sealant 100 ml tube UFS 740sw DVB S receiver with connecting cables infrared sensor and infrared remote control MobiSet 3 digital CAP 700 installation and operating instructions UFS 740sw satellite receiver operating manual PROPER USE PROPER USE USE FOR T
26. athed in May lead to irritation On being swallowed May lead to health problems 12 Ecological data Additional instructions Do not allow to run into the drains bodies of water or the ground 13 Disposal instructions Product Recommendations In accordance with the applicable waste labelling regulations waste should be classified by its origin Therefore a unique waste code number cannot be assigned Packaging Recommendations Packaging that is empty of residues should be sent for recycling Packaging that contains residues of hazardous substances or which is contaminated with hazardous substances and any packaging that is not empty of residues should be disposed of as the product correctly and without creating pollution If the last contents makes it necessary packaging that is empty of residues must be pre treated for disposal e g washed out neutralised cured shaken out 14 Transport data ADR RID Further data Not hazardous cargo IMO IMDG Marine pollutant no Further data Not hazardous cargo IATA ICAO Further data Not hazardous cargo 15 Regulations Identification in accordance with EC directives The product should be classified and identified in accordance with EC directives national statute law Component s to be labelled as hazardous content 4 4 methylene diphenyl diisocyanate Hazard symbols Xn Hazardous to health 38 SIKAFLEX 291 SAFETY DATA SHEET Risk phrases 42 Sensitisation poss
27. ched to the roof of the vehicle by adhesive and is secured by additional screws Note that the curing of the adhesive sealant is temperature dependent It reaches its full strength only after approximately five days During installation work comply strictly with the processing and safety instructions for the adhesive sealant Sikaflex 291 safety data sheet and Sikaflex 291 technical data sheet SAFETY INSTRUCTIONS IMPORTANT NOTES Road Traffic Licensing Regulations StVZO The applicable regulations of the SIVZO must be observed in respect of fixed installation of the turntable on a vehicle which is driven on public highways In particular 88 19 2 30 C 32 2 and the EC directive 74 483 EEC are applicable Briefly they state that no endorsement of the vehicle documentation is required unless the antenna unit causes the height of the laden vehicle to exceed 2 m or the antenna unit projects beyond the outer lateral outline of the vehicle The maximum permissible height of 4 m vehicle and antenna unit may not be exceeded There is an increased risk of accidents if the normal vehicle height is increased by extending the antenna The driver bears sole responsibility for the condition of the superstructure and external fittings Cables Lay all cables such that nobody can tread on them or trip over them To prevent parasitic induction or interference emissions when extending the antenna cable use 75 Q coaxial cable with a screening
28. d cable fire hazard e At the connecting point for the power cable the voltage must not fall below 10 9 V even with a load of 12 A Otherwise optimum functioning can no longer be guaranteed e Connect the power cable to the respective socket in your motor home or caravan 12 V or 230 V 21 INSTALLATION AND CONNECTION Only for connection in a motor home not in a caravan e The green connecting cable marked IGNITION allows you the option of connection to a circuit in the vehicle that is activated when the ignition key is turned and then carries a continuous 12 V supply This type of connection ensures that when the engine is started the antenna is automatically lowered into the park position the receiver does not need to be turned on Note that the antenna can then be lowered only when the power supply is present in addition to the ignition signal e Check the connections before you re connect the on board power supply e For commissioning and more detailed information on additional operator functions we refer you to the separate operating manual enclosed FUNCTIONAL INSTRUCTIONS FOR CONNECTION TO THE ON BOARD POWER SUPPLY Under certain circumstances problems can arise when the units are connected to different connecting sockets or circuits earth potentials If no others are available it is recommended that you connect the connecting sockets for receiver and TV set to the same cable as shown in Figure G The c
29. e Cross head screwdrivers for M3 and M5 screws e Torque wrench capacity 6 to 11 Nm e Hexagon socket key 5 mm e Two wooden beams for supporting the turntable UNPACKING AND PREPARATION The CAP 700 must not be mounted on the satellite dish since this could cause it to distort Keep the CAP 700 in its cardboard box for transport on to the vehicle roof Retain the original packaging as if it is necessary to send the unit for repair transport damage cannot be ruled out and the manufacturer accepts no liability for possible damage Loosen the six fastening screws width A F 10 mm Carefully lift the turntable off the mounting b La plate and place it on the prepared wooden supports Make sure that the cables are not The CAP 700 packaging can be opened along crushed where they emerge from the underside of both long sides This allows easier access to the the turntable fastening screws SELECTING THE INSTALLATION LOCATION Essentially the cable lengths of the MobiSet 3 CAP 700 components allow you a free choice of installation location on your caravan or motor home However you should take note of the following points e Before installation you should find out whether the operating manual for your vehicle permits the fitting of non vehicle specific parts or what requirements need to be met in order to do so e For direct satellite reception there should be no obstructions between the antenna and the satellite Therefore mak
30. e cable duct when placing the turntable on to the mounting plate Make sure that the cables are not crossed over and that they are taut so that they cannot be crushed Do not try to pull the cables from the unit This could damage the cables or loosen the cable connections Place the turntable carefully on the mounting plate The through holes on the turntable must be perfectly aligned with the threaded holes on the mounting plate Apply a little adhesive sealant to the six threaded holes in the mounting plate and screw the fastening screws into the thread Tighten the screws to a torque of 6 Nm When feeding the cables through the HDZ 100 roof gland make sure they are not crushed kinked or damaged INSTALLATION AND CONNECTION BRIEF INSTRUCTIONS FOR INSTALLING THE TURNTABLE The sequence of pictures shown illustrates all the necessary installation steps that are required to install the turntable and the BAS 60 parabolic reflector on the roof of the vehicle The other detailed instructions in this installation and operating manual must also be followed Determination of installation location Caution System has a turning range of 162 cm Drill hole with Q 38 mm Deburr sharp edges of hole Apply Sikaflex 291 adhesive to the spigot of the roof gland Insert the spigot into the hole and secure it from below with the knurled nut Unscrew screws x 6 10 AF from the mounting plate and remove the mounting plate
31. e ee 26 SAFETY NOTE ent ee ye kota amazon a pate petet a kk kat ty kk on taa 28 ETING OFE RATON ne en ee ee D n E 28 MANUAL LOWERING TO PARK POSITION e e ee ennan anana 00000 nn KEREN KEEN EE ENKEN KENNEN en 30 SAFETY NOTES 30 MANUAL LOWERING E 31 TECHNICAL DATA e are at ji ao a et a dann naar nn e aa a e a E 32 SIKAFLEX 291 SAFETY DATA SHEET een ns een 35 SIKAFLEX 291 TECHNICAL DATA SHEET nn 40 CAP 700 OPERATING MANUAL ee 42 IMPORTANT INFORMATION FOR CAP 700 BEFORE SETUP un nenn nennen 43 Sidler KREE 43 FIRST INSTALLATION ns ae ea ee ee een A4 ALIGNMENT SATELLITE SEARCH en nn a e tk kk a a lk jn CU n e ka l ak n 48 MOVING THE ANTENNA MANUALLY 5 55 kt ia kan ai duin mu e e a a n ke n pe au ken kn a e e a kb n kk came 49 CHANNEL SATELLITE SELECTION svi au tie kid asie vi semi kt st oi lk a a e kk n n RE e kd pk 50 CHANNEL SELECTION FROM THE CHANNEL LIST ee 50 CHANGE OF LOCATION TIMER PROGRAMMING Ee RE ERKENNEN KEEN KEEN EEN EEN nnn 51 RESET PARKING E 52 RESETTING THE TURN TABLE ANTENNA on anne ik klip tas Fuer koua io kab kiye s 92 PARKING THE Aarte 53 SPECIAL MESSAGES FROM THE TURNTABLE trett set tran ii n tl a na a n a n m l ka l a a dv a 54 DECLARATION OF CONFORMITY u a to a kk a a kk n l ee 58 FOR YOUR NO TE Seesen ou akte ie ai at a l l tt it at l ki a en a a a e l n a F af n n kn ki e n Pa e a a 59 2 FOREIGN LANGUAGE INSTALLATION MANUALS DISP
32. e of bridging small gaps caused by the curvature of the vehicle s roof However you should ensure that the mounting plate is not bent by tightening the screws Remove any adhesive sealant that leaks out at the sides with a clean cloth or if necessary with Sikaflex Remover available from specialist dealers Do not use cleaning agents or thinners containing solvents as this could damage the adhesive sealant applied under the mounting plate Use only cleansing paste and water to clean your hands Secure the cable gland from inside the vehicle by tightening the knurled nut supplied Fig A Note that the curing of the adhesive sealant depends on the ambient temperature and the humidity Final strength is reached after approx five days However this need not restrict further installation work since the mounting plate is held in place by the tightened screws INSTALLATION OF TURNTABLE VARIANT WITH CABLE GLAND UNDERNEATH THE TURNTABLE 14 Feed the ends of the cables with the connectors as far as possible through the cable gland into the interior of the vehicle INSTALLATION AND CONNECTION Figure E Direction of travel E fC Battery ignition Gasket with plug for Receivers the unused duct e Lift up the turntable and place it carefully on the mounting plate facing in the direction of travel see illustration Fig E do not step on the plug connector and do not kink crush the cables The
33. e sure that the antenna is not shadowed by roof extensions such as luggage racks air conditioning units solar panels etc The problem of shadowing applies also to the selection of the parking place for your vehicle For interference free satellite reception the antenna needs a projected free view to the South at an angle of between 0 and 75 depending on location to the horizontal 9 INSTALLATION AND CONNECTION e When selecting the installation position take into account the range of movement of the turntable see graphics and the Technical Data chapter There must be no structures on the roof that would obstruct this range of movement risk of collision For safety keep at least the required area free for ease of installation and any subsequent dismantling Elevation 45 Direction of travel ii Elevation max 75 Park position 7 We gt D 2 A LL Ys The eight o neighbou ing attachments on the roof may lead to shadowing Area radius min 566 mm within which the device with its height of up to 230 mm can j oea P be attached to the clear space turntable radius min 807 mm Roof attachments may be mounted within the hatched area INSTALLATION AND CONNECTION e Choose an installation position on the roof that is as horizontal as possible or only slightly sloping depending on the location of the vehicle since roof inclinations great
34. e turntable to the park position and let it cool down there Press the EI button and the turntable will move to the park position Note The antenna should not be moved whilst the battery is being recharged to prevent peak loads when turning on 54 SPECIAL MESSAGES FROM THE TURNTABLE The vehicle ignition was switched on For safety reasons the turntable moves into the park position This operates however only if the green ignition cable for the turntable is connected to the vehicle ignition and the turntable is connected to the power supply As long as voltage is present at the ignition the connection to the CAP will remain disabled This means the CAP cannot be operated If the turntable encounters an obstruction the CAP reverses 10 This allows the obstacle to be removed more easily The turn table antenna has reached the mechanical stop or is jammed Check whether the turntable is obstructed e g by a branch 59 A serious software error has occurred Reset the turntable in the CAP menu or contact our service centre The turn table antenna software is defective An update is required Contact our service centre 56 This message may also appear if the ignition is switched on voltage is present at the ignition cable green The receiver has lost communication with the turntable Check the connection between the UFS 740sw and the turntable the power supply and whether possibly the ignition sig
35. er attach the sticker from the supplementary sheet Lower the CAP 700 WA antenna while driving where it can easily be seen by the person operating the ignition switch km h Safety precautions during operation During operation of the turntable make sure that no persons in particular children are in the immediate vicinity of the turntable and that they cannot touch any moving parts crush hazard Always unplug the power supply during installation work Exceeding the normal vehicle height by failing to lower the antenna increases the risk of accidents The driver is responsible for the condition of external fittings on the vehicle In addition the instructions in the installation and operating manuals for these devices and for the attachments and superstructures must be complied with at all times If stormy weather is expected the turntable must always be moved to the park position otherwise both the CAP 700 and the vehicle may be damaged INSTALLATION AND CONNECTION REQUIRED TOOLS AND EQUIPMENT e Circular cutter 38 mm e Flat bladed screwdriver for M5 screws e Power drill e Galvanised round head screws depending on the roof structure 5 mm sheet metal screws D 7981 depending on the roof structure or round head screws D 7985 with washers and nuts e Twist drill 2 5 or 5 5 mm e Round file and or emery paper e Cleaning agent e Open ended or ring spanners 10 and 11 mm across flats e Knife
36. er than 5 may lead to problems when searching for the satellite e To ensure secure adhesion the height difference of the roof curve may not be more than 1 cm over a length of 2 m as otherwise the gap between the roof and the mounting plate would be too great to be filled by the adhesive sealant e As the vehicle is constantly subjected to vibration loads during travel the roof below the antenna unit IS also subject to significant loads Please note given the nature and capacity of your vehicle roof see also operating manual for the vehicle that the weight of the antenna unit is approx 9 7 kg In case of doubt consult a qualified dealer or your vehicle s manufacturer e The roof gland provides a watertight seal through which the two connecting cables coax cable and power supply cable are fed into the interior of the vehicle directly underneath the turntable lf you prefer a different method of laying the cables they can be run from the rear of the turntable via the channel provided in the mounting plate The cables must then be run along the roof of the vehicle in a protective cable duct not supplied Note Do not cut the cables short as otherwise the proper functioning of the unit can no longer be Quaranteed INSTALLATION STEPS INSTALLATION OF CABLE GLAND AND MOUNTING PLATE Note If you had previously used a Kathrein HDM140 141 flexible satellite mast or another mast with a diameter of 34 mm you can continue using the existing
37. fore fit the UFS 740sw out of sight in any location e g on cupboard walls side walls or the base of storage compartments In addition the following points should be taken into account The wall thickness at the installation location must be at least 12 mm as otherwise the screws will break through on the other side or damage the surface The receiver must be placed in such a way as to allow sufficient air circulation behind above and next to the unit installation using the installation kit ensures this Installation on carpet covered walls is therefore unsuitable Ensure that the cupboard or storage compartment in which the unit is housed is adequately ventilated to prevent a build up of heat Take care when tightening the screws not to damage any cables etc behind or in the wall The receiver is designed for installation in exclusively dry interior locations The installation location must be protected against moisture The connecting cables must be provided with strain reliefs The receiver must be connected to no other power supply than 12 V DC The receiver s earth connection must be connected to the negative pole of the motor home or caravan battery SUSPENDED INSTALLATION Al 9 05 TU 00 19 INSTALLATION AND CONNECTION NP S Py ALL SI Zw pa OV OSS SCH a SR XO SSE MK e N n oz SAJ Eat SI aa T bi TAG J iS PUTNI Remove the wood screws supplied from their transport
38. gent available from specialist dealers e g Sika Cleaner or a primer e g Sika Primer The procedure for gluing the mounting plate is as follows Figure D Recess for cable Adhesive areas between the two grooves 13 INSTALLATION AND CONNECTION Ensure before starting adhesive work that the temperature of materials to be glued and the adhesive sealant is between 5 C and 40 C Prepare all necessary fasteners and tools Prepare the tube of adhesive sealant in accordance with the instructions enclosed with the tube Remove the roof gland Fig A and apply the adhesive sealant evenly to the underside of the roof gland flange Replace the roof gland in the drilled hole and press it firmly against the roof of the vehicle Apply the adhesive sealant evenly to the underside of the mounting plate completely covering the area within the circular groove Fig D This area of the vehicle roof must be completely coated with adhesive in order to achieve the necessary bonding force Place the mounting plate on the roof of the vehicle as you did previously when marking out the drilled holes Make sure that the arrow on the mounting plate points forward in the direction of travel The fastening holes must be perfectly aligned with the prepared holes in the roof Fasten the mounting plate in place with the prepared screws evenly tightening six screws across the diagonals Note The adhesive sealant used is capabl
39. gland hole in the roof if space allows Figure A O Ring Adhesive e n the centre of the intended position of the turntable drill the opening for the cable gland with a circular cutter 0 38 mm Deburr the hole with a round file or emery paper e Provisionally insert the roof gland into the drilled hole Fig A e Place the mounting plate on the roof of the vehicle such that the centre hole is positioned centrally to the cable gland The arrow symbol must be visible from above and point forwards in the direction of travel Fig B 11 Figure B INSTALLATION AND CONNECTION Arrow in the direction of travel Mark out the positions of the six fastening holes on the roof of the vehicle in a circular pattern Note The size of the holes and the choice of fastening screws to be used not supplied Figure C 12 depend on the type and thickness of the materials used in the roof structure If the roof panelling plastic roofs is sufficiently strong it is recommended that round head screws plain washers and self locking nuts are always used to secure the glued mounting plate For very thin roof panel materials and insufficient support in the insulating material through holes 5 5 mm into the interior of the vehicle are necessary galvanised M5 round head screws of sufficient length should then be used Make sure that you use a sufficiently strong support that can accept the bolt tensile forces large plai
40. ia Compatible with all extinguishing media in general use Special hazard from the product its products of combustion or gases released In case of fire the following can be released Carbon monoxide CO Carbon dioxide CO Hydrogen chloride HCl Oxides of nitrogen NC Additional instructions Combustion residues and contaminated extinguishing media must be disposed of in accordance with the local authority regulations Collect contaminated extinguishing water separately do not allow it to run into the drains 6 Measures if inadvertently released Personal precautions Ensure sufficient ventilation Wear protective clothing Where vapours dust aerosols are present wear a breathing mask Environmental protection measures Do not allow to run into the drains or bodies of water In the event of penetration into water ground or drains inform the responsible authorities Procedure for cleaning clearing up Absorb with media that bind to liquids e g sand sawdust universal binding media Dispose of the material that has been cleared up in accordance with the chapter on Disposal 7 Handling and storage Handling Instructions for safe handling Refer to Chapter 8 Personal protective equipment Instructions for fire and explosion prevention Not applicable Storage Requirements for storerooms and containers Containers should be dry kept tightly sealed and stored in a cool well ventilated place Storage proximity instructions St
41. ible by breathing in Safety phrases 23 Do not breathe in gas smoke vapour aerosol 45 IN the event of accident or feeling unwell summon a doctor immediately if possible show the doctor this label Special identification of particular components Contains isocyanates Follow the manufacturer s instructions National regulations Water contamination class WGK 1 to VwVws of 17 May 1999 GISCODE PRODUCT CODE GISCODE PU 50 16 Other data Markings in the left margin indicate revisions from the previous version Intended purpose Chemical product for building and industry Risk phrases for the constituent substances listed in chapter 2 10 Flammable 20 Hazardous to health if breathed in 20 21 Hazardous to health if breathed in and if comes in contact with the skin 36 37 38 Irritates the eyes breathing organs and the skin 38 Irritates the skin 42 43 Sensitisation possible by breathing in and by contact with the skin 91 59 Poisonous to water organisms can have long term polluting effects on bodies of water 65 Hazardous to health can cause damage to lungs if swallowed 66 Repeated contact can lead to brittle or cracked skin 67 Vapours can cause drowsiness and light headedness The data in this safety data sheet represent our knowledge at the time of publication They are not warranted as a complete list of characteristics The only warranty extended is that expressed in the technical data sheets and the general c
42. ied the require can be painted over ments of the International Maritime can be sanded Organisation IMO broad bonding spectrum Sikaflex 291 is manufactured in ac electrically non conductive cordance with the ISO 9001 14001 resistant to seawater and hydro Quality Assurance System and the lysis Responsible Care Programme Application Range Sikaflex 291 is a versatile product for use in boatbuilding and shipbuilding to make flexible and vibration resistant seals in internal and external areas Sikaflex 291 has strong bonding pro perties to the principal materials used in shipbuilding Suitable substrates in clude wood metals primers and paint finishes 2 component system cera mic materials plastics UP GFK etc Sikaflex 291 should not be used for sealing plastics that are subject to stress cracking such as PMMA PC etc For timber decking we recommend Si kaflex 290 DC In the cured condition Sikaflex 291 can be sanded without problems Curing mechanism Sikaflex 291 1 2 SIKAFLEX 291 TECHNICAL DATA SHEET The cross linking reaction of Sikaf lex 291 occurs in the presence of atmospheric moisture At lower tem peratures the water content of the air is less and the cross linking reaction proceeds somewhat more slowly see diagram 12 23 Layer thickness mm 2 4 6 Time days Diagram 1 Through curing speed of Sikaflex
43. lite covers with its transmission beam spot within which satellite reception is possible The transmission power is at its greatest in the centre of this spot it becomes progressively weaker moving outwards You should preferably align your antenna to the position of the ASTRA satellite 19 2 East picture below left EUTELSAT HOTBIRD 13 East picture below right The spots for these satellites are shown below The inner line of the footprint here shows the area covered by the digital signals from the ASTRA satellite The outer dashed line of the footprint displayed here shows the area that is covered by individual ASTRA satellite There fore not all channels are available within this footprint The satellites broadcast the various channel packages in different footprints Within these the respective channel packages can be received with good video and audio quality In the marginal zones reception is possible although the quality of the signals received can vary considerably 24 DISMANTLING FOR SERVICING lf repairs to the system or individual components are necessary contact your specialist dealer or our Service centre see below for address A Never open the turntable yourself DISMANTLING e Do not cut the cables At the cable junction provided disconnect the cables projecting from the turntable from the two cables laid within the interior of the vehicle unplug the plug e The cables laid within the
44. mbH Street postcode Kornwestheimer Str 103 107 Postcode and town Stuttgart Country Germany Tel 49 711 80090 Fax 49 711 8009321 General information Product safety Emergency information hotline 49 173 6774799 only outside office hours 2 Composition data on components Chemical characterisation Filled reactive PUR polymer Hazardous contents designation to 67 548 EEC CAS No Concentration Danger symbols R phrases EC no Naphtha crude oil hydro desulphurised heavy G4742 82 1 1 2 5 Yo Xn N 10 65 51 53 66 67 265 185 4 4 4 methylene diphenyl diisocyanate 101 68 8 0 1 1 Xn 20 36 37 38 42 43 202 966 0 Xylol 1330 20 7 1 2 5 Yo Xn 10 20 21 38 215 535 7 3 Potential hazards Hazard designation Xn Hazardous to health Special hazard instructions for human beings and the environment 42 Sensitisation possible by breathing in 4 First Aid measures General instructions In all cases show the doctor the safety data sheet After breathing in In the event of trouble consult a doctor After contact with the skin After contact wash the skin with soap and water In the event of continuing skin irritation consult a doctor After contact with the eyes In case of contact with the eyes wash with copious water for 15 minutes Summon a doctor immediately After swallowing Do not induce vomiting Summon a doctor immediately 35 SIKAFLEX 291 SAFETY DATA SHEET 5 Measures for fire fighting Suitable extinguishing med
45. n washers or a complete reinforcing plate Not supplied i Adhesive area Alternative between the two roof attachment grooves INSTALLATION AND CONNECTION Create the holes necessary to secure the mounting plate Fig C n addition to the screwed connection the mounting plate and roof gland must be bonded to the roof with adhesive and sealed This is done using the Sikaflex 291 adhesive sealant supplied which is ideally suited for this purpose thanks to its broad range of adhesion Before starting to use Sikaflex 291 adhesive sealant be sure to read the Sikaflex Products safety data sheet and technical data sheet in this installation manual The prerequisite for good adhesive characteristics is a clean dry and grease free substrate You should therefore clean the roof surface with a suitable cleaning agent within a circumference of 35 cm around the drilled hole and allow the surface to dry thoroughly If the surface is painted ensure that the paint finish is sufficiently well bonded to the substrate If the coat of paint is already loose or peeling it must be removed down to a stable layer in the area to which the adhesive will bond If you have any doubts concerning the adhesive characteristics consult a paint and lacquer specialist or the manufacturer of your vehicle Under certain circumstances it may be necessary for you to improve the adhesive properties of the roof surface by pre treatment with a cleaning a
46. nal is present at the CAP The connection to the turntable is defective Reset the turntable in the CAP menu check the connections between the turntable and receiver or contact our service centre 57 DECLARATION OF CONFORMITY EC Declaration of Conformity Hersteller Manufacturer Kathrein Werke KG Anschrift Address Postfach 10 04 44 83004 Rosenheim Produktbezeichnung Product Sat Paket MobiSet 3 Typenbezeichnung Type CAP 700 Bestellnummer Article number 20310019 Die Kathrein Werke KG best tigt hiermit dass das bezeichnete Produkt mit den folgenden Richtlinien zur Angleichung der Rechtsvorschriften bereinstimmt The Kathrein Werke KG hereby confirm that the designated product complies with the following directives on the harmonisation of the laws a Elektromagnetische Vertr glichkeit EMC 2004 108 EC vom 15 12 2004 Folgende Normen werden eingehalten Applied harmonised standards EN 55013 2001 A1 2003 A2 2006 EN 55020 2007 b Maschinen Machinery 2006 42 EC vom 17 05 2006 Folgende Normen werden eingehalten Applied harmonised standards EN ISO 12100 1 2003 EN ISO 12100 2 2003 EN ISO 13857 2008 EN 349 1993 A1 2008 Entwicklung Produktion Qualit tssicherung und Vertrieb basieren auf der Norm EN ISO 9001 Development production quality assurance and marketing are based on the standard EN ISO 9001 Ort Datum Rosenheim 04 07 07 Place Date Rechtsverbindliche Unter
47. onditions of sale Consult the technical data sheet before use 39 40 Technical data sheet Version 12 2005 Sikaflex 291 The strongly bonding marine adhesive Technical characteristics Chemical basis 1 component polyurethane Colour white black natural wood SIKAFLEX 291 TECHNICAL DATA SHEET Curing mechanism Density before curing DIN 53479 cures by absorbing moisture approx 1 3 kg l depending on colour Stability good Processing temperature 5 C 40 C Skin formation time Through curing speed Volume change DIN 52451 60 min see digiagram 1 approx 5 Shore A hardness ISO 868 DIN 53505 approx 40 Tensile strength ISO 527 DIN 53504 Elongation at break ISO 527 DIN 53504 1 8 N mm approx 400 Tear propagation resistance ISO 34 DIN 53515 Glass transition temperature ISO 4663 DIN 53445 Operating temperature short term approx 6 N mm approx 45 C sustained 40 C to 90 C 4 hours 160 C 1 hour 180 C Storage life storage at less than 25 C in unopened containers 12 months 23 C 50 r Lf Description Product advantages Sikaflex 291 is a stable 1 compo 1 component nent polyurethane sealant developed flexible for boatbuilding and shipbuilding low odour On exposure to atmospheric moisture resistant to ageing and weather it reacts to become an elastomer non corrosive Sikaflex 291 satisf
48. ore separately from all kinds of foodstuffs Additional instructions for storage Protect against frost Protect against heat and direct sunlight Protect against atmospheric humidity and water 8 Exposure limitation and personal protective equipment Components subject to monitoring of workplace concentration limits Designation of the component CAS no type Reference country year Naphtha crude oil hydro desulphurised heavy 64742 82 1 Permissible workplace concentration 350 mg m TRGS 900 DE 2004 64742 82 1 Permissible workplace concentration 70 ml m TRGS 900 DE 2004 36 Markings in the left margin indicate revisions from the previous version SIKAFLEX 291 SAFETY DATA SHEET 4 4 methylene diphenyl diisocyanate Xylol Personal protective equipment 101 68 8 101 68 8 1330 20 7 1330 20 7 1330 20 7 1330 20 7 1330 20 7 1330 20 7 Permissible workplace concentration Permissible workplace concentration Permissible workplace concentration Permissible workplace concentration EU TWA 8h EU TWA 8h EU STEL 15 EU STEL 15 General protective and hygiene measures Ensure sufficient ventilation at the workplace Avoid contact with the eyes and skin Apply prophylactic skin protection by protective hand cream Take off soiled clothing immediately Do not smoke eat or drink when handling the product Before breaks and after completing work wash hands well Breathing protection When ventilation
49. red number of degrees the scale is located on the bottom on the LNB an N ATISOU U III OO LT I Tighten the hexagon socket screw to a torque of 3 3 3 5 Nm Leave the installation location and reconnect the UFS 740sw to the power supply First switch the receiver on at the main switch then press any of the numeric buttons Wait until the message Position of Astra is not known Start search is displayed abort this procedure using the button Next press the eo button to go to the main menu and use the a buttons to move to the Settings menu item Confirm the selection by pressing the button Use the 4 buttons to move to the Antenna Configuration menu item Confirm the selection by pressing the button Use the 4 buttons to move to the menu item Reset the turn table antenna Confirm the selection by pressing the button Once the antenna has been reset you can return to the normal TV picture by pressing the button View after installation 445 View after installation 45 29 MANUAL LOWERING TO PARK POSITION f a defect arises in the electronic controls after some disassembly work the satellite dish can be returned to the park position horizontal position manually Following this however recalibration by an authorised workshop is always necessary Driving to the nearest workshop with the antenna extended at a moderate speed and taking
50. ructions for this in the CAP unit installation manual The antenna is moved to park position and this is then confirmed Thursday 21 12 2006 5 11 05 The Antenna Configuration menu allows you to check whether the antenna truly is in the park position 53 SPECIAL MESSAGES FROM THE TURNTABLE SYSTEM PROTECTION MESSAGES The following messages are shown on the screen to protect your reception system and the on board power supply Astra 19 2 search started The power sup ply for the turn table antenna is insufficient The power supply to the turntable is inadequate battery voltage below the minimum value The turntable can still be moved but communication errors can occur between the UFS 740sw and the turntable e g when scanning for satellites If the voltage falls still further both the following error messages are displayed Antenna can move to park position only because of low power si upply voltage or critical temperature Press the EI button to acknowledge the displayed message The turntable cannot be moved any more Check the power supply to the turntable Check the power supply to the turntable and whether it is obstructed e g by a branch If both causes of faults are displayed the turntable motor temperature is in the critical range Allow the turntable to stand for a few minutes in its current position until the turntable motor temperature has reduced You can also however move th
51. schrift i V Binding signature FOR YOUR NOTES 59 Internet http www kathrein de KATHREIN KATHREIN Werke KG Anton Kathrein Stra e 1 3 P O Box 100 444 83004 Rosenheim GERMANY Antennen Electronic 936 341 7 0908 ZWT Technical data subject to change
52. sort order is displayed from where you selected the last channel At the top left you will see the selected channel list TV Channel or Radio Channel displayed Press the lu blue button to switch between the TV and radio channel lists Underneath you can see the channel list with the sort order you selected The channel list can display channels sorted by various selection and sorting criteria For instance you can use the IQ buttons to display various channel lists sorted by satellite e g ASTRA 19 2 or Hotbird 13 Use the cursor buttons QJ 906 to select the desired channel in the various channel list views Confirm the selection of the desired channel by pressing the button As soon as the turntable has found the satellite or has reached the known position you will hear and view the currently selected channel in the small window at the top right To exit the channel list and return to the TV picture press the button again or press the button Note A comprehensive explanation of the channel list with its detailed functions e g the scan and sort function can be found in the UFS 740sw operating manual 50 CHANGE OF LOCATION TIMER PROGRAMMING After a change of location the antenna moves to the last position selected After initialisation you will therefore see the following display example as it depends on the last selected position For slight changes of location the antenna can find the satellite very quickl
53. ta sheets for their essential physical safety toxicological and ecological data The applicable regulations such as the hazardous substances regulations should be complied with On request we will send you our sys tem data sheet TM 7510 Instructions for protection at work for handling Sika Deutschland GmbH products Note The details above especially the suggestions for the processing and use of our products are based on our knowledge and experience in normal cases providing the products are correctly stored and ap plied Due to the variety of materials surfaces and variations in working conditions no guarantee of a work product or liability from any legal relationship can be founded on these instructions or on oral advice unless we are charged with premeditated or gross negligence Here the user must prove that he brought to Sika s attention promptly completely and in writing all knowledge necessary for Sika to make an objective assessment of expectation of Success It is the user s responsibility to check the products for suitability for the intended application We reserve the right to change the product specifi cations The trademark rights of third parties must be respected In all other respects our respective sales and delivery conditions apply The latest version of the technical data sheet is applicable and should be requested from us as uu ww Sikaflex 291 2 2 41 CAP 700 OPERATING MANUAL The
54. te The maximum permissible speed for vehicles with a CAP 700 receiver unit mounted on the roof is 130 km h Before commencing a journey the satellite dish must always be lowered into horizontal position park position The turntable may be operated in an ambient temperature range of 20 C to 45 C Operating the system outside this range may result in malfunctions or damage to the system When choosing the location for installation or raising the UFS 740sw ensure there is adequate ventilation The system may only be installed by qualified specialist personnel To prevent hazards during installation operation or when driving on public highways the instructions and information in this manual must be strictly adhered to Proper installation and connection of the system are pre requisites for conformity with the corresponding standards This is documented in advance by the CE mark and the declaration of conformity in the appendix to this manual SAFETY INSTRUCTIONS IMPORTANT NOTES Safety during installation work When carrying out installation work in locations where there is a risk of falling take appropriate safety precautions e g use of a working platform Make sure that the vehicle roof is sufficiently strong and stable to carry out the installation work risk of damage or collapsing of roof In case of doubt contact a qualified specialist dealer or the manufacturer of your vehicle to find an appropriate installation loca
55. tion Make sure that The turntable and connected units are disconnected from the power supply The person carrying out the installation or repair does not suffer from vertigo and can move around safely on the roof of the caravan or motor home The person carrying out the installation or repair is wearing sturdy and non slip shoes The person carrying out the installation or repair has a secure position to stand and hold on while working The roof and the climbing equipment used e g ladder are dry clean and non slip The roof can withstand the weight of the person carrying out the repairs Attention Risk of death or injury due to falling or the roof collapsing Nobody should be inside the caravan motor home underneath the antenna during dismantling installation Attention Risk of death or injury due to possible roof collapsing and falling parts Proper installation and safety Essential information A crucial safety factor is proper performance of installation and electrical connection work and the specified alignment of the turntable in the direction of travel park position see also installation and connection Comply as precisely as possible with the installation conditions and steps described Modifications to the electrical installations in the vehicle should only be carried out by a specialist in vehicle electrics Do not make any unauthorised changes to the turntable Adhesive sealant The turntable is atta
56. tons Available options German English French Italian Spanish Czech Dutch Norwegian and Turkish Press the 8 green button to move to the next menu Note If you are unsure whether you chose the right option from a previous menu you can go back a step at any time during the first installation process by pressing the O red button 44 The following display appears Presort for G Germany 2 Use the oo buttons to select whether to replace the default channel list with one pre sorted for Germany Austria Switzerland or Italy If you want to use the default channel list choose No under Restore Channellist Press the KN green button to move to the next menu The following display appears TV aspect ratio GQ 4 3 Use the OLOT buttons here to select the settings for your TV set When doing this refer to the operating instructions for your TV set 45 TV aspect ratio Select the TV s picture format Either 4 3 or 16 9 Picture format Here you select the type of screen display depending on the setting of your TV format TV format 4 3 Pan 8 Scan picture is clipped or Letterbox black bands above and below TV format 16 9 Always 16 9 or automatic TV Scart Output Select the type of video signal at the TV Scart socket here Select the signal that your TV set can process FBAS Composite Colour Baseband Signal RGB Red Green Blue signal or Y C S Video sign
57. trees or other obstructions This will save you time and effort So as to avoid overheating the turntable motors do not operate the motors continuously for longer than 10 minutes None of the search procedures initiated by the CAP 700 will require as much as 10 minutes operation Only repeated unsuccessful search procedures or manual overrides by the user can cause this limit to be exceeded REMOTE CONTROL All settings on the UFS 740 are made using the remote 43 FIRST INSTALLATION Before using your unit for the first time read the Safety Instructions Important Information and Installation and Connection sections You will find a sample configuration for a motor home in the Section Installation and Connection Connection Example Do not connect the receiver to the power supply until all installation work has been properly carried out The guidance given in the First Installation section assumes that the receiver has been properly connected as per the Safety Instructions Important Information and Installation and Connection sections First switch your TV set on and select the AV channel slot Switch on your receiver at the power switch on the front of the unit The following display appears Also pay attention to the bars at the bottom of the on screen display These provide information on what to do next Select the menu language you want using the v 4 but
58. urrent rating of the circuit used must be checked with respect to the intended application Further information on operating the UFS 740sw receiver can be found in the operating manual supplied with the unit 22 INSTALLATION AND CONNECTION CONNECTION EXAMPLE FOR 12 V BATTERY CONNECTION Figure G Important For operation with two batteries it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the turntable Non compliance means that the automatic lowering function will not work Ensure the cable polarity is correct UFS 740 brown white green e cy A ih d on B 6 pin E Master EEE T Battery 10 9V 13 8V Ignition Xs A m TV set External IR sensor A Cigarette lighter socket or 12V DIN ISO 4165 standard socket lic e les ayo Battery x not supplied 23 RECEPTION RANGE FOOTPRINT The footprint is the reception area on the earth that a satel
59. y lf the satellite is not found at the Astra 19 2 known position the search starts automatically lf the search is unsuccessful the following message appears 7 Pa A ollam mE VR den An OO I lan rosm on oT unknown aa dum Ar RN Lol DENIM REM ram f FA amm m Lg 8 A AJ rer ar m m FALLI e is al Sep ELIT Lec LC Eu If a signal is found the antenna automatically goes into fine tuning mode max 90 seconds if signal is adequate the position is immediately saved TIMER PROGRAMMING See the UFS 740sw operating manual for details of how to program the timer When using the UFS 740sw on a CAP 700 please note the following additional instruction To prevent the turntable rotating at a time when it is unsupervised or when rotation might be irritating e g in the middle of the night a timer can be set During the timer period the turntable is active only if the UFS 740sw is in operation or is in standby mode If the receiver is completely switched off switched off at the power socket and or the turntable is in park position the turntable will be inactive during the timer period The same applies if during the first movement the satellite position is not found 51 RESET PARKING RESETTING THE TURN TABLE ANTENNA Press the a button to return to the main menu The DO buttons and button allow you to call up the submenus Settings Antenna Configuration Thursday 21 1
60. y cable 3 pin plug to the battery Avoid laying the cables across sharp edges and protect the cables against possible chafing points e Connect the coaxial cable coming from the turntable to the IF IN F socket on the rear of the UFS 740sw Place the infrared sensor for the receiver close to or directly on top of the TV set and lay the cable to the UFS 740sw Connect the 6 pin Western connector at the rear to the socket marked IR REMOTE IN Note Lay the AV cinch enclosed with the CAP 700 to the Scart cable Take great care to plug the cables into the correct sockets The cinch connector must be assigned to the UFS 740sw and the Scart connector to the TV set They must not be reversed or the unit will not function CONNECTING TO THE UFS 740SW Isolate the on board power supply master switch off or disconnect the positive pole of the on board power supply battery before commencing the following work e Connect the power cable supplied depending on the power supply available in your motor home or caravan either a 12 V supply or a 230 V supply via a power supply unit to the 12V 2 5A socket on the receiver Make sure that the inline integrated fuse 5 A of the cable is fully plugged in and is intact If the fuse blows the source of the fault must first be eliminated The fuse must only ever be replaced by a fuse with the same rating 5 A The fuses in the cable and in the receiver may never be bridge

Kathrein CAP 700 Turntable User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents