JVC LST0420-001B Security Camera User Manual
Contents
1. OFF a s ON 1 AGC OFF ON 2 SELECT PHASE WHT BAL 3 SYNC LL INT 4 WHT BAL ATW MANUAL 5 BLC OFF ON 6 DAY NIGHT OFF ON 7 ALARM TRIGGER STATE 8 RESET SPOT RESET SPOT IRIS LEVEL Iris level adjustment For adjusting the level of the automatic aperture control lens This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side NOTE Prior to adjusting the aperture level ensure to set the 1 AGC Switch of the function selection switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sensitivity and the picture may look uneven 12 ZOOM FOCUS MEMORY zoom focus adjustment switches position memory button Use the ATELE and WWIDE switches to zoom and the 4FAR and 9 NEAR switches to adjust focus rs pg 25 Press the MEMORY button to register the position r gt pg 25 ALARM POSITION status indication lamp Light off Registration of home position is enabled Light on red Lens initializing Light on green Registration of alarm position is enabled Blinking green Position memory registration mode memory registration completed pg 25 POSITION SELECT POSITION SELECT button Press this button to switch between the home and alarm positions Display on the status2. Upon switching between the HOME and ALARM positions the camera focus may change slightly after the zoom operation comes to a stop This is due to the built in lensperformance and is not a malfunction TK C215V12 only When the camera is moved from a cold area to room temperature condensation may occur causing the camera to malfunction as a result In this case turn on the power after waiting for a few hours This unit enlarges the rotation angle to support wide range set up When the zoom of the lens is set to WIDE end and the tilt angle is set around 80 the dome cover can be visible into the image depending on the rotation angle In this case adjust the image angle if necessary re pg 23 All Interconnecting Equipment must be UL Listed llNote on consumable parts TK C215V12 only The following parts are consumable and should be replaced after a certain number of hours or a count of operations The service lives given below are only typical values They may vary depending on the operating environment and conditions Note that the replacement of consumable parts is chargeable even when they are replaced before the termination of the warranty period e Zoom lens assembly Zooming operation 2 million times Introduction Name of Parts Camera Mounting hole elliptical x 4 Use these when mounting the camera to the electrical box pg 22
3. within 30 seconds after pressing the ZOOM FOCUS button e When adjusting the iris level set the AGC Switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sensitivity and the picture may look uneven X Home position registration is completed 25 Adjusting Image Adjusting Images continued lg TK C215V12 continued Registering alarm position 1 2 3 2 For registering the angle of view during monitoring when there is an alarm input RESET SPOT 233 114 1 5 L sc Por rov oMrDCUS AR 4 NAR Y 9 MEMOR POSITION lala mm e ee Check that the ALARM POSITION indicator light is turned on Registration of alarm position is enabled e Press the POSITION SELECT button if the ALARM POSITION indicator light is off Adjust the image size pg 25 Press the MEMORY button for 2 seconds or longer The ALARM POSITION indicator light blinks for 3 times green X ALARM position registration is completed Adjust the brightness t pg 25 Press the POSITION SELECT button The camera returns to the home position NOTE Be sure to return the camera to the home position after registration of the alarm position is completed In addition to pressing the POSITION SELECT button you can also use the power ON OFF button to return the camera t
4. B buttons are used as adjustment buttons Default setting WHT BAL SYNC Synchronization system selection switch This switch sets the synchronizing system for the camera INT This is set for internal synchronization LL Line Lock The camera s vertical synchronization is locked to the AC 24 V power line frequency When switching between multiple cameras using a switcher selecting this mode and adjusting the vertical phase can reduce the monitor sync disturbances occur that when the camera image is switched 60 Hz only Default setting INT WHT BAL ATW MANUAL selection switch For selecting whether to adjust the white balance automatically or manually When the setting is changed from manual to ATW the setting values in the manual mode will be reset The camera switches to the same mode as with pressing the RESET button NOTE NOTE e The white balance of this camera is preset to use under sunlight or halogen lamps and may not be properly adjusted when used under artificial lights such as fluorescent lights Default setting ATW BLC Backlight compensation switch When the object is placed against the light setting this to ON increases the iris aperture by 1 stop and the object will appear clearer Default setting OFF To capture a subject with continually changing brightness day night set this switch to ON The camera automatically captures the im
5. Mounting hole round x 4 Use these when mounting the camera to the ceiling or wall pg 18 20 Outer Case Use this in the following cases e When mounting the camera directly to the ceiling or on the wall amp pg 20 e When mounting the camera to the electrical box pg 22 Dome Cover The dome cover is fragile Take care when handling it Inner Dome Before mounting the camera remove it and perform switch setting and image angle setting r amp pg 18 20 Wiring Hole Break and use this when drawing the cable from the camera unit without drilling a hole in the ceiling r amp pg 22 Input Power cable DC 12 V Input Red 412 V Black GND AC 24 V Input Non polar s pg 16 Q Alarm signal cable TK C215V12 only Yellow ALARM IN Gray ALARM GND pg 15 Q Protection Cover Upon connecting the coaxial cable protect it by insulating the metal part of the BNC connector from the ceiling structure Video signal output connector BNC pg 14 Camera Interior The dome cover inner dome and outer case are removed Procedures for removal r amp pg 18 Embedding the camera to the ceiling Step 3 to Step 5 Lens c Next page TK C215V4 is used in the above illustration Strap A plate to connect the camera unit and the dome cover D Fastening Screw x 3 When embedding the camera in the ceiling turn this
6. indication lamp will change accordingly s pg 25 RESET SPOT RESET SPOT button When this button is pressed the value of the white balance or phase adjusted manually is reset to the default value e When the 2 SELECT switch is set to WHT BAL the white balance is reset to the default value When the switch is set to PHASE the phase is reset to the default value e When setting to SPOT When this button is pressed white spots are corrected For instructions on correcting white spots see White spot correction pg 28 Q R B R B adjustment button This button is pressed when manually adjusting the white balance or when adjusting the vertical phase of the line lock The function of this button is selected using the 2 SELECT switch e When manually adjusting the white balance Press the R button to increase the red tint and decrease the blue tint Press the B button to increase the blue tint and decrease the red tint e When adjusting the phase Press the or button to adjust the phase Function selection switches 1 AGC Auto gain control switch Setting this switch to ON automatically increases the sensitivity even when the brightness of the subject is insufficient Default setting ON 2 SELECT WHT BAL PHASE setting switch 6 DAY NIGHT Easy DAY amp NIGHT switch WHT BAL The R B buttons are used as R B adjustment buttons PHASE The R
7. not be properly adjusted when used under artificial lights such as fluorescent lights BLC Backlight compensation switch When the object is placed against the light setting this to ON increases the iris aperture by 1 stop and the object will appear clearer Default setting OFF DAY NIGHT Easy Day amp Night switch To capture a subject with continually changing brightness day night set this switch to ON The camera automatically captures the image in color when the subject is bright and in black and white mode when it is dark Default setting OFF NOTE e When this item is set to ON the AGC feature will automatically be set to ON regardless of the AGC Switch 1 setting e The Easy DAY amp NIGHT feature on this camera uses a sensitized black and white mode unlike other black and white surveillance cameras that use infra red lighting e Sensitivity increases in the case of black and white images The screen may therefore appear rougher and white spots may increase RESERVED Not used Ensure to set this to OFF before using the camera Default setting OFF RESET SPOT RESET SPOT CORRECTION selection switch RESET The RESET SPOT button is used as a RESET button SPOT The RESET SPOT button is used as a SPOT button r amp pg 28 Default setting RESET IRIS LEVEL Iris level adjustment For adjusting the level of the automat
8. sheath cables are used Conductor diameter mm 1 0mm 91 6mm o 2 0 mm AWG18 AWG14 AWG12 50m 140m 220m Honec e DC V amp eom so 720f laximum extension acoay 30m 350m 550m 420ft 11008 1800ft 30m 80m 130 m celle DC12V tgof 260f 420ft laximum extension AC24V 80m 210m 340m 260ft 680ft 1100f1 CAUTION e lf thin cables are used i e with a high resistance a significant voltage drop will occur when the unit is at its maximum power consumption Either use a thick cable to restrict the voltage drop at the camera side to below 10 or place the power supply near to the camera When the voltage is low the protection circuit within the camera may be triggered and the power of the camera may turn off automatically e Do not allow input from both a DC 12 V and AC 24 V power supply at the same time e When using a DC 12 V power supply ensure that the polarities of the cable are correct e The product shall be powered by Class 2 only Electrical Specifications of Alarm Input Terminals TK C215V12 only e To prevent penetration of noise in the internal circuitry apply a non voltage contact signal to the ALARM input terminal Never apply a voltage e Apply an alarm signal for at least 200 ms If it is shorter it is not guaranteed that the signal will be recognized as an alarm signal e Under the alarm status statu
9. system Line lock Internal Video S N 50 dB AGC OFF white 50 output Horizontal resolution 540 TV lines Center Typ Minimum illumination Typical e TK C215V4 Color mode 2 5 Ix F1 3 AGC ON 50 0 8 Ix F1 3 AGC ON 25 Black and White mode 1 4 Ix F1 3 AGC ON 50 0 4 Ix F1 3 AGC ON 25 e TK C215V12 Color mode 3 5 Ix F1 3 AGC ON 50 1 1 Ix F1 3 AGC ON 25 Black and White mode 2 0 Ix F1 3 AGC ON 50 0 6 Ix F1 3 AGC ON 25 White balance ATW Manual Switchable Color temperature range 2 300 K to 10 000 K Backlight compensation ON OFF Switchable Easy DAY amp NIGHT ON OFF Switchable Bi Lens Focal length TK C215V4 2 8 mm to 10 mm variable TK C215V12 3 8 mm to 45 6 mm variable Zoom ratio TK C215V4 Approx 3 6 TK C215V12 Approx 12 Maximum aperture TK C215V4 F1 3 f 2 8 mm to F3 0 f 10 mm TK C215V12 F1 6 f 2 3 8 mm to F2 7 f 2 45 6 mm Angle adjustment range Pan 175 Rotation 175 Tilt 80 Angle of vision TK C215V4 f 2 8 mm 73 H x 54 V f 10mm 20 H x 15 V TK C215V12 f 3 8 mm 52 H x 39 V f 45 6 mm 4 5 H x 3 4 V E General Power supply AC 24 V 60 Hz DC 12V Power consumption TK C215V4 4 2 W TK C215V12 6 6 W Ambient temperature 14 F to 122 F 10 C to 50 C Operation 32 F to 104 F 0 C to 40 C Recommended Mass TK C215V4 Approx 1 43
10. unit please read the instruction manual carefully in order to make sure that the best possible performance is obtained Characteristics IS Realizing a High Picture Quality This camera realizes 540 TV lines and S N50 dB by employing a highly sensitive CCD with 380 000 pixels and a high resolution video processing circuit E Enlarged Shooting Range The adjustment range of the shooting direction is wide and mounting of the camera to the wall is possible with the employment of 3 axis rotation mechanism ll Non Camera Like Design Dome type design allows application in various locations ll Embedding in Ceiling Without Use of Metal Fittings There is no need to use a separate recess bracket when embedding this camera to the ceiling lil High Magnification Varifocal Zoom Lens TK C215V4 and TK C215V12 only The built in x3 6 varifocal lens TK C215V4 and X12 zoom lens TK C215V12 enables detailed supervision ll Alarm Zoom Feature TK C215V12 only 2 preset positions are available which allow setting of the monitoring screen size under normal circumstances and during alarm input ll Easy DAY amp NIGHT Feature A Easy DAY amp NIGHT feature is available which switches automatically to a black and white image when the object is dark This is useful for supervision in a dark environment How to Use This Manual ll Characters and symbols used in this manual CAUTION Points to pay attention to d
11. 5V4 RESETIISPOT C SPOT button 0 N 2 4 Wr BAL ART Function selection switch 8 TK C215V12 a m 2 E SPOT button SS BOO uw a gt 2 dy l S 2 Er Er Function selection EN A s 3 switch 8 SEL z Fr p zaoz UE gu 2 25 28 1 Remove the dome cover 2 Cover the lens surface using a black sheet of paper etc so that light does not enter the lens 3 Set the function selection switch 8 to SPOT pg 11 13 4 Press and hold the SPOT CORRECTION button for more than 2 seconds e White spot correction will start Correction may take several seconds for completion NOTE e Maximum correction 32 e The white spot correction feature of this unit does not guarantee the correction of all white spots Depending on the characteristic of white Spots correction may not be possible e When performing white spot correction accurate data may not be achieved in case of highly detailed pixels since correction is made using the information of surrounding pixels e The result of white spot correction is maintained until the next correction is performed Others Specifications E Camera Signal system Based on NTSC standard Scanning frequencies 15 734 kHz Horizontal 59 94 Hz Vertical Image device 1 4 IT CCD Effective picture elements 380 000 pixels 768 H x 494 V Sync
12. Class Best important operating and conforme a la norme NMB 003 du Canada maintenance servicing instructions in the literature accompanying the appliance P INFORMATION FOR USA E INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help ll CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS DEVICE COMPLIES W
13. ITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION This installation shall be in accordance with the National Electrical Code ANSI NFPA 70 Any Mention in this manual of Alarm inputs have not been evaluated by UL to be used for Burglar Alarm Functionality Embedding of cameras in the ceiling may not be allowed due to regulations in some regions Please consult your nearby authorized JVC dealer for more details The ceiling to mount the camera has to be strong enough to support the weight of this product If the ceiling is not strong enough make sure to apply reinforcement to the ceiling before installation Be sure to tighten the screws and nuts securely Insufficient tightening may cause the unit to fall from its mount The rating label is displayed on the side of the camera unit The camera unit may fall if the mounting screws and nuts are not properly tightened Ensure that the screws and nuts are properly tightened We do not accept liability for any damage to the camera in cases when it is dropped because of incomplete installation due to not observing the installation instructions correctly Please be careful when installing the camera Do not install the camera near lighting equipment w
14. Ibs 650 g TK C215V12 Approx 1 54 Ibs 700 g Accessories Instructions 1 Warranty Card 1 Service Information Card RS Templalex s ss rere nen 29 Others Specifications continued ll External Dimensions Unit mm inches When cover is attached 121 4 3 4 4 04 5 46 1 13 16 3 16 e e 6 1 4 i a I B S SHED Hd aaj Dila e gt a slg S When embedded 0116 4 9 16 0145 5 3 4 Specifications and appearance of this unit and related products are subject to change for product improvement without prior notice 30 Focus chart 31 2006 Victor Company of Japan Limited LST0420 001B Vu3IWVO9 3NOd CLASLZO ML VASLZO ML
15. JVC DOME CAMERA TK C215V4 INSTRUCTIONS TK C215V12 A TK C215V4 is used in the above illustration For Customer Use Enter below the Serial No which is located on the body Retain this information for future reference Model No TK C215V4 TK C215V12 Serial No LST0420 001B Introduction Safety Precautions Information for Users on Disposal of Old Equipment European Union This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end of life Instead the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment recovery and recycling in accordance with your national legislation By disposing of this product correctly you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this NEN product For more information about collection point and recycling of this product please contact your local municipal office your household waste disposal service or the shop where you purchased the product Attention Penalties may be applicable for incorrect disposal of this waste in accordance This symbol is with national legislation Only valid n the Business users European Union p If you wish to dispose of
16. V4 Set the video setting switches on the camera unit before mounting it To set the switches use a fine tipped screwdriver p RESET SPOT f a SS e TOJ 4 Function selection switch setting table Items in bold are factory position OFF m aj ON 1 AGC OFF ON 2 SELECT PHASE WHT BAL 3 SYNC LL INT 4 WHT BAL ATW MANU 5 BLC OFF ON 6 DAY NIGHT OFF ON 7 RESERVED W SET TO OFF 8 RESET SPOT RESET SPOT o IRESET SPOT RESET SPOT button When this button is pressed the value of the white balance or phase adjusted manually is reset to the default value e When the 2 SELECT switch is set to WHT BAL the white balance is reset to the default value When the switch is set to PHASE the phase is reset to the default value e When setting to SPOT When this button is pressed white spots are corrected For instructions on correcting white spots see White spot correction t pg 28 R B R B adjustment button This button is pressed when manually adjusting the white balance or when adjusting the vertical phase of the line lock The function of this button is selected using the 2 SELECT switch e When manually adjusting the white balance Press the R button to increase the red tint and decrease the blue tint Press the B button to increase the blue tint and decrease the
17. age in color when the subject is bright and in black and white mode when it is dark Default setting OFF e When this item is set to ON the AGC feature will automatically be set to ON regardless of the AGC Switch 1 setting e The Easy DAY amp NIGHT feature on this camera uses a sensitized black and white mode unlike other black and white surveillance cameras that use infra red lighting e Sensitivity increases in the case of black and white images The screen may therefore appear rougher and white spots may increase ALARM alarm input mode selection switch For setting the lens movement when there is an alarm input Set according to the alarm device that you are using pg 15 Electrical Specifications of Alarm Input Terminals t pg 23 Adjusting Images TRIGGER Upon input of an alarm the lens moves to the preset zoom focus position alarm position The lens remains in the alarm position for 15 seconds before it returns automatically to the home position When there is a new alarm input while the lens is at the alarm position the lens continues to remain in the alarm position for 15 seconds upon the last alarm input STATE Upon input of an alarm the lens moves to the preset zoom focus position alarm position The lens remains in the alarm position for 15 seconds The lens will after a lapse of 15 seconds continue shooting at the alarm position as long as there is al
18. arm input The lens returns automatically to the home position immediately after alarm input stops Default setting TRIGGER RESET SPOT RESET SPOT correction selection switch RESET The RESET SPOT button is used as a RESET button SPOT The RESET SPOT button is used as a SPOT button r amp pg 28 Default setting RESET 13 Installation and connection About Connection Cables The maximum connection distance varies with the type of cable used Please refer carefully to the table for each cable during connection Be sure to turn off the power of devices before connecting cables C a To video Signal Cable gt To DC 12 V or AC 24 V Power Supply y etat a an i do on ii qi oe jn gi c d 9 To Alarm Signal Cable Si TK C215V12 only I lt s 1 1 e Fumana semine Video signal cables Connect the coaxial cables BNC to the video signal output connector BNC Cable Maximum extension No cable compensator RG 59 200m RG 6 350m RG 11 450m 14 DC 12 V or AC 24 V power supply cable Connect the DC 12 V or the AC 24 V power supply to the DC 12 V AC 24 V terminals on the terminal board To prevent connection errors or a cable disconnection we recommend the use of lug plates for the connections The following table shows the connection distances and connection cables provided that 2 conductor VVF cables vinyl insulated vinyl
19. era sensitivity is automatically boosted and the picture may look uneven This is not a malfunction however When this camera is used in the ATW mode the recorded colors may be slightly different from the actual colors due to the operational principles of the auto tracking white balance circuit This is however not a malfunction If a high intensity object such as a lamp is shot the image on the screen may have vertical lines smear or blur blooming at its periphery This is a characteristic of the CCD and is not a defect Observe the following when carrying out camera maintenance e Turn the power OFF before proceeding to carry out maintenance e Clean the dome cover lens using a lens wiper cloth or a tissue If it is contaminated seriously clean the contaminated part with a cloth or a tissue which has been soaked in a solution of water and a neutral detergent If the DAY NIGHT switch is turned on the mode changes automatically to black and white in dark places As the sensitivity increases the image may look grainy and white spots may appear When changing modes bright portions of image may be emphasized but this is not a failure of the camera When the supply voltage of the camera is low the input protection circuit within the camera may be triggered and the power of the camera may turn off automatically Make sure to use a supply voltage for the camera that is within 10 96 of the rated voltage
20. fastening screw CAUTION e Moving the lens unit without loosening the pan fastening screw may damage the lens unit 7 Set the switches for video images TK C215V4 pg 10 TK C215V12 pg 12 Inner Dome 6 4 wa 5 Pan fastening Camera Fastening Screw TK C215V4 is used in the above illustration E Connecting 1 Align with the shooting direction when mounting the outer case to the ceiling Notes on outer case mounting screws not supplied e Height of screw head should be less than 4 mm e The diameter of the attachment hole of outer case is 9 4 5 mm 3 16 inch e Do not use flathead screws e When using an impact screwdriver do not tighten the screws fully Tighten using your hand instead Failure to do so may damage the outer case 2 Hang the fall prevention wire that has been dismantled in Step 5 3 of the setup procedures to the hook 3 Attach the fall prevention wire to the camera Fall prevention wire is not included CAUTION eTighten all screws securely Otherwise the camera may come loose and fall Outer case mounting screws Less than 4 mm the ceiling slab Fall prevention wire not supplied Be sure to loosen the screw TK C215V4 is used in the above illustration 4 Connect the video signal cable pg 14 Lower the protection cover and connect the connectors Upon connecting restore the protection c
21. hat the embedded cover recess bracket is securely attached before installing the camera e Please refer to the instruction manual for the cover in use for details on installation of the embedded cover recess bracket For detail related to embedded cover rsecess bracket please contact JVC Ceiling TK C215V4 is used in the above illustration Embedded Cover in Ceiling recess bracket Selecting a mounting method Select a method for mounting the camera according to the intended purpose Embedding the camera to the ceiling s pg 18 When mounting the camera directly to the ceiling or on the wall c pg 20 When mounting the camera to the electrical box t pg 22 Mount by allowing the cable to exit from the side pg 22 17 Installation and connection Mounting the Camera continued Embedding the camera to the ceiling Make use of a ceiling material with a thickness between 9 5 mm to 22 mm Bi Setup 1 Open a hole in the ceiling 0120 mm 4 3 4 inches 2 Draw the fall prevention wire mounted to the ceiling slab and the cable out from the ceiling in advance CAUTION e Select a suitable fall prevention wire based on length strength location material insulation property etc Use a ring on the fall prevention wire for mounting to the camera unit with an internal diameter of at least 23 1 mm or and not larger than 95 5 mm and an ex
22. he MONITOR terminal of this camera to a test monitor to adjust the camera s shooting direction image and focus The power to the camera body must be ON when adjustments are performed MONITOR Terminal Terminate it with 75Q Test Monitor TK C215V4 is used in the above illustration Adjusting the camera direction The camera unit can be adjusted horizontally or vertically and rotated Adjust the camera in the direction of the object CAUTION e Please discharge a static electricity by touching to a MONITOR Terminal by hand before adjust the angle of view e Before adjusting the shooting direction of the camera ensure that the pan fastening screw is loosened Moving the lens unit without loosening the pan fastening screw may damage the lens unit Rotation 175 Tilt 80 Camera s shooting direction mark SS Pan center mark Rotation center mark iR RING Pan Fastening Screw Be sure to loosen the screw before adjusting Rotation Knob Always adjust the rotation by holding this W knob xd Xr sem C Um Eri os EL TK C215V4 is used in the above illustration NOTE e Pan rotation of 175 is possible from each of the camera s shooting direction mark pan center mark and rotation center mark When adjusting the rotation do not hold the lens unit Always adjust by holding the rotation knob e When using the camera at
23. ic aperture control lens This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side NOTE Prior to adjusting the aperture level ensure to set the AGC Switch 1 of the function selection switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sensitivity and the picture may look uneven FOCUS ADJUST focus adjustment button Use this to adjust the lens focus Upon pressing the lens aperture will open up for about 30 seconds such that the depth of field becomes shallower thus enabling focus to be easily adjusted pg 24 NOTE The electronic shutter functions automatically upon pressing the focus adjustment button and the screen may flicker However this is not a malfunction Q Focus adjustment ring Move this to the left right to adjust the focus Zoom adjustment ring Move this to the left right to adjust the field angle 11 Introduction Setting the Lens and Switches TK C215V12 Set the video setting switches on the camera unit before mounting it To set the switches use a fine tipped screwdriver I En Y ALARM rum Function selection switch setting table Items in bold are factory position
24. ith a high temperature such as spotlights Doing so may cause malfunction or fire The unit is to be powered by a DC 12 V or an AC 24 V power supply The unit is to be powered by a UL Listed DC 12 V or an AC 24 V power supply The AC 24 V and 12 V DC power supply shall conform to the following Class 2 only This installation should be made by a qualified Service person and should conform to all local codes Before starting an important recording be sure to perform a test recording in order to confirm that a normal recording is possible We will not provide any compensation whatsoever for the contents to be recorded or loss of opportunities when recording is not properly performed due to malfunction of the video camera VTR hard disk recorder or video tape Prior to adjusting the shooting direction of the camera touch the metal surface of the MONITOR terminal with your hand to discharge static electricity from your body Introduction These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances IMPORTANT SAFEGUARDS Read all of these instructions Save these instructions for later use All warnings on the product and in the operating instructions should be adhered to Unplug this appliance system from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use attachments not rec
25. locations with strong vibration stabilize by tightening the tile fastening screw and pan fastening screw to prevent distortion of the camera s field angle CAUTION e Moving the camera beyond its adjustable range may cause failure in maintaining the performance of this camera e As this camera has a wide tilt rotation range a part of this camera may appear on the screen depending on the field angle and orientation e Do not hold the lens unit when adjusting the direction of the camera Applying force on the lens unit may damage it 23 Adjusting Image Adjusting Images continued Adjusting the field angle focus brightness Upon determining the imaging direction adjust the field angle focus and iris level accordingly The method of adjustment varies with the camera in use TK C215V4 r pg 24 TK C215V12 gt pg 25 24 B TK C215V4 Iris Level Adjustment Focus Adjust Button Focus ring Nal F Adjusting field angle Loosen the fastening screw for the zoom adjustment ring and move the ring to the left right to adjust the image Adjusting focus Press the FOCUS ADJUST button The iris will be opened for 30 seconds Loosen the fastening screw for the focus adjustment ring and move the ring to the left right to align the focus NOTE e Set by repeating Adjusting field angle and Adjusting focus for 2 to 3 times After adjustment is completed fasten by tightening each
26. m Align with shooting direction 2 Follow steps 2 to 7 of When mounting the camera directly to the ceiling or on the wall Bl Connecting pg 20 E Mounting 1 Attach the camera to the outer case that has been fastened to the electrical box Follow steps 1 to 3 of When mounting the camera directly to the ceiling or on the wall Bl Mounting s gt pg 21 E Adjusting Images After mounting is completed adjust the images while checking the actual image pg 23 Adjusting Images 22 Mount by allowing the cable to exit from the side When mounting the camera to the ceiling or a wall it is possible to guide the cable from the side without opening any holes The basic mounting method is identical to steps in When mounting the camera directly to the ceiling or on the wall pg 20 1 Break the cable extraction hole using a pair of long nose pliers 2 Pull out the cable from the extraction hole and mount it to the ceiling or wall 3 Connecting the cable Follow steps 4 to 7 of When mounting the camera directly to the ceiling or on the wall Bl Connecting r amp pg 21 Ss 4 Adjusting Images After mounting is completed adjust the images while checking the actual image pg 23 Adjusting Images Adjusting Image Adjusting Images Upon mounting the camera adjust the images while checking the actual image Mounting the test monitor Connect t
27. marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company For appliance designed to operate from battery power refer to the operating instructions 10 For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it form the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 11 Do not allow anything to rest on the power cord Do not locate this appliance where the cord will be abused by persons walking on it 12 Follow all warnings and instructions marked on the appliance 13 Do not overload wall outlets and extension cords as this can result in fire or electric shock 14 Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous volta age points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the appliance 15 Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 16 Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the appliance c Ifthe a
28. o the home position e To check images at the registered home position or alarm position press the POSITION SELECT button Press this button to switch between the image at the home and alarm positions 6 Other installation and adjustment Mounting the Inner Dome After setting is complete mount the Inner dome Claws 3 locations Inner Dome TK C215V4 is used in the above illustration 1 Mount the inner dome Mount the inner dome to the claws 3 locations CAUTION e Mount the inner dome such that it does not cover the lens e When mounting the inner dome be careful not to move the lens position The image angle set previously will go out of alignment Mounting the Dome Cover After setting is complete mount the dome cover 1 Mount the dome cover Align the position marks on the camera unit and dome cover followed by pressing in directly to mount the cover CAUTION Press the dome over until a click sound is heard Check that the cover is firmly mounted Failure to mount the cover firmly may cause this cover to fall off 27 Other installation and adjustment White spot correction As a general characteristic unique to CCDs white spots may appear on the screen with age In order to reduce this phenomenon this unit is equipped with a white spot correction feature Switch on the camera power supply and wait for at least 30 minutes TK C21
29. of the fastening screws eThe electronic shutter functions automatically upon pressing the focus adjustment button and the screen may flicker However this is not a malfunction Adjusting brightness This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side NOTE e For adjusting the brightness do not conduct it within 30 seconds after pressing the focus button e When adjusting the iris level set the AGC Switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sensitivity and the picture may look uneven Bi TK C215V12 2 types of angle of view may be selected for TK C215V12 In general set in a way such that the home position shoots a wide range and the alarm position a narrow range e Use the alarm input mode selection switch to set the actions when there is an alarm input c pg 13 CAUTION e When setting images on TK C215V12 ensure that the lens is covered using the dome cover This camera is equipped with a high magnification lens When adjustment is not performed through the cover the lens may go out of focus when the cover is attached e When adjusting the focus ensure that the optical axis of the lens and the center of the dome cover are aligned and that the screen is not distorted See ill
30. ommended by the appliance manufacturer as they may cause hazards Do not use this appliance near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool etc Do not place this appliance on an unstable cart stand or table The appliance may PORTABLE CART WARNING fall causing serious injury to a child or adult and serious damage to the appliance symbol provided by RETAC Use only with a cart or stand recommended by the manufacturer or sold with the appliance Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer An appliance and cart combination should be moved with care e Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn 8 Slots and openings in the cabinet and the back or bottom are pro vided for VA cs ventilation and to insure reliable operation of the appliance and to protect it from sS3125A overheating these openings must not be blocked or covered The openings should never be blocked by placing the appliance on a bed sofa rug or other similar surface This appliance should never be placed near or over a radiator or heat register This appliance should not be placed in a built in installation such as a bookcase unless proper ventilation is provided 9 This appliance should be operated only from the type of power source indicated on the
31. over to cover the connectors 5 Connect the input power supply cable pg 16 6 Connect the alarm cable TK C215V12 only pg 15 7 Wrap insulation tape around cables IN _ Alarm signal cable TK C215V12 only Solder or crimp t UJ Insul i Protection e cover Wrap with tape Input power supply cable TK C215V 12 is used in the above illustration E Mounting 1 Align the position mark of the fastened outer case with that of the camera unit NOTE When doing so be careful not to catch the cables in the outer case 2 Turn the camera unit in the clockwise direction x When doing so ensure that the O mark is visible See illustration below 3 Fasten the camera by tightening the camera fastening screw Position mark TK C215V4 is used in the above illustration E Adjusting Images After mounting is completed adjust the images while checking the actual image pg 23 Adjusting Images 21 Installation and connection Mounting the Camera continued When mounting the camera to the electrical box NOTE Before mounting the camera to electrical boxes please refer to local building codes for box type to use for low voltage wiring E Connecting 1 Align with the shooting direction when mounting the cover to the electrical box Outer case mounting screws Less than 4m
32. ppliance has been exposed to rain or water d Ifthe appliance does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation e Ifthe appliance has been dropped or the cabinet has been damaged f When the appliance exhibits a distinct change in performance this indicates a need for service 17 When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 18 Upon completion of any service or repairs to this appliance ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition N oc POND Contents Introduction Safety Precautions seene 2 Contents eere icd He c ge D actives 5 Characteristics nter 6 Operating Precautions 7 Namie ot ParlS uz nc eee 8 o nic TP 8 Camera Interior sess 9 Setting the Lens and Switches TK C215V4 10 Setting the Lens and Switches TK C215V12 tiv ua tete tees 12 Installation and connec
33. red tint e When adjusting the phase Press the or button to adjust the phase Function selection switches 1 AGC Auto gain control switch Setting this switch to ON automatically increases the sensitivity even when the brightness of the subject is insufficient Default setting ON SELECT WHT BAL PHASE setting switch WHT BAL The Q R B buttons are used as R B adjustment buttons PHASE The Q R B buttons are used as adjustment buttons Default setting WHT BAL SYNC Synchronization system selection switch This switch sets the synchronizing system for the camera INT This is set for internal synchronization LL Line Lock The camera s vertical synchronization is locked to the AC 24 V 60 Hz power line frequency When switching between multiple cameras using a switcher selecting this mode and adjusting the vertical phase can reduce the monitor sync disturbances occur that when the camera image is switched Default setting INT 4 WHT BAL ATW MANUAL selection switch For selecting whether to adjust the white balance automatically or manually When the setting is changed from manual to ATW the setting values in the manual mode will be reset The camera switches to the same mode as with pressing the RESET button Default setting ATW NOTE e The white balance of this camera is preset to use under sunlight or halogen lamps and may
34. s when the metal contact is make select the contact or connecting wire such that the maximum wire resistance between the ALARM IN and ALARM GND is within 150 Q ALARMIN ALARM GND Polarity of alarm signals ALARM INPUT SHORT CONTACT ALARM OPEN NORMAL HOME POSITION 15 Installation and connection System diagram TK C215V4 Video signal TK C215V12 Video signal Alarm signal METAL CONTACT l I EL B Power Unit DC 12 V or AC 24 V VIDEO IN MONITOR Digital Video Recorder etc NOTE NOTE e Turn OFF the power supply to all equipment to e Power consumption of TK C215V4 TK be used before making connections C215V12 are different from one another e Read the Instruction Manual for each piece of When installing a mixture of these models equipment to be used before making select a cable length according to the power connections consumption of each model Alternatively install based on the model with the highest power consumption 16 Mounting the Camera Getting Started CAUTION e When mounting the camera to the ceiling ensure to wear safety glasses to protect the eye from any falling object Attachment of a embedded cover in the ceiling recess bracket may be mandatory in certain regions If this is so ensure t
35. screw to secure the camera This Screw belongs to a part of the ceiling mount bracket D B MONITOR terminal RCA pin pg 23 D Camera Unit Fall Prevention Wire Fastening Hook D Fall Prevention Wire Supplied and Wire Mounting Screw These are the wires and screws connecting the camera unit and the outer case One end of the wire is connected to the hook D securing the safety wire Ceiling Mount Bracket x 3 This is used as a bracket when embedding the camera to the ceiling pg 18 D Camera Fastening Screw Use this to fasten the camera unit D to the outer case To remove r pg 18 20 Camera Unit Rear Pan fastening Screw Ensure to loosen the screw before setting Further tighten the screw to ensure that camera s shooting direction does not go out of alignment only when it is used in a location with strong vibration r amp pg 23 Imaging Direction mark Install the camera by aligning the imaging direction with the arrow mark Rotation Knob Rotate the lens unit to adjust the inclination of the image to be turned Rotation Center Mark pg 23 Tilt fastening Screw Tighten the screw to ensure that camera s shooting direction does not go out of alignment when it is used in a location with strong vibration pg 24 Fall Prevention Wire mounting hole amp Screw Fall Prevention Wire not included Introduction Setting the Lens and Switches TK C215
36. ternal diameter that is not larger than 9 mm 9120 mm 4 3 4 inches Fall prevention wire V Approx 100 mm not supplied 3 7 8 inches 2 Power supply cable TK C215V12 only 3 Remove the dome cover As illustrated in the diagram hold the dome ring such that the position mark comes between the thumb and index finger Turn the ring in the counterclockwise direction to remove 3 x Dome Ring CT mark 18 Claws 3 locations 4 Remove the inner dome The inner dome is secured with claws 3 locations Hold the inner dome and remove it from the claws 5 Remove the outer case This method does not require an outer case D Loosen the camera fastening screw with a screwdriver To remove turn the camera unit in the counterclockwise direction Dismantle the supplied fall prevention wire Unfasten the mounting screw for the fall prevention wire at the rear of the camera unit Loosen the pan fastening screw CAUTION Moving the lens unit without loosening the pan fastening screw may damage the lens unit Set the switches for video images TK C215V4 pg 10 TK C215V12 pg 12 Inner Dome w 5 Ean Fastening Crew TK C215V4 is used in the above illustration E Connecting 1 Fall prevention not supplied Attach the fall prevention wire to the camera followed by attaching it to the ceiling slab Fall pre
37. this product please visit our web page www jvc europe com to obtain information about the take back of the product Other Countries outside the European Union If you wish to dispose of this product please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment FOR USA AND CANADA Due to design modifications data given in this instruction book are subject to possible change without prior notice CAUTION PO NOT OPEN TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR THIS APPLIANCE TO RAIN OR BACK NO USER SERVICEABLE PARTS MOISTURE INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AVERTISSEMENT POUR EVITER LES RISQUES The lightning flash wish arrowhead D INCENDIE OU D ELECTROCUTION symbol within an equilateral NE PAS EXPOSER L APPAREIL A triangle isintended to alert the user L HUMIDITE OU A LA PLUIE to the presence of uninsulated gt dangerous voltage within the INFORMATION FOR CANADA product s enclosure thatmay be of RENSEIGNEMENT POUR CANADA sufficient magnitude to constitute a risk of electric shock to persons This Class B digital apparatus complies with The exclamation point within an Canadian ICES 093 equilateral triangle is intended to alert theuser to the presence of Cet appareil numerique de la
38. tion About Connection Cables 14 Video signal cables 14 DC 12 V or AC 24 V power supply Cable etc canine gains 14 Electrical Specifications of Alarm Input Terminals esses 15 System diagram sss 16 Mounting the Camera 17 Getting Started 17 Selecting a mounting method 17 Embedding the camera to the ceiling 18 When mounting the camera directly to the ceiling or on the wall 20 When mounting the camera to the electrical box 22 Mount by allowing the cable to exit from the side 22 Adjusting Image Adjusting Images 23 Mounting the test monitor we 23 Adjusting the camera direction 23 Adjusting the field angle focus brightness 24 Other installation and adjustment Mounting the Inner Dome 27 Mounting the Dome Cover 27 White spot correction 28 Others Specifications 29 Introduction Thank you for purchasing this product These instructions are for TK C215V4U TK C215V12U Before beginning to operate this
39. ual image pg 23 Adjusting Images 19 Installation and connection Mounting the Camera continued When mounting the camera directly to the ceiling or on the wall When mounting to a wall replace areas indicated as ceiling in the procedures by wall Bi Setup 1 Open a hole in the ceiling o 30 mm 1 1 8 inches Make use of the template supplied to open a hole 2 Draw the fall prevention wire mounted to the ceiling slab and the cable out from the ceiling in advance CAUTION e Select a suitable fall prevention wire based on length strength location material insulation property etc Use a ring on the fall prevention wire for mounting to the camera unit with an internal diameter of at least 3 1 mm or and not larger than 5 5 mm and an external diameter that is not larger than 9 9 mm 3 Remove the dome cover As illustrated in the diagram hold the dome ring such that the position mark comes between the thumb and index finger Turn the ring in the counterclockwise direction to remove 3 Dome Ring CT mark 4 Remove the inner dome The inner dome is secured with claws 3 locations Hold the inner dome and remove it from the claws 5 Remove the outer case D Loosen the camera fastening screw with a screwdriver To remove turn the camera unit in the counterclockwise direction Dismantle the fall prevention wire 20 6 Loosen the pan
40. uring operation NOTE Details for reference such as functions or constraints during use 1S Pages or items to refer to e All product names that appear in this document are the trademarks or registered trademarks of their respective companies Marks and symbols such as and do not appear in this document Operating Precautions To save energy when it is not being used turn the system s power off This camera has been designed for indoor use It cannot be used outdoors Do not install or use the camera in the following places n a place exposed to rain or moisture e In a place with vapor or oil soot for example in a kitchen e In a temperature outside the operating temperature range 10 C to 50 C e Near a source of radiation X rays strong radio waves or magnetism ein a place where corrosive gasses are generated en a place subject to vibration e n a place with excessive dirt en an environment where there is cold air or near the air outlet of an air conditioner If this camera and the cables connected to this camera are used where there are strong electromagnetic waves or where there is magnetism present for example near a radio or TV transmitter power transformer or an electric motor the picture may produce noise and the colors may be affected This camera incorporates an AGC circuit As a result when it is used under low light conditions the cam
41. ustration below S ie 2 Registering home position For registering the angle of view during monitoring under normal conditions m WHT BAL 2 3 1 1 Check that the ALARM POSITION indicator light is turned off Registration of home position is enabled Press the POSITION SELECT button if the ALARM POSITION indicator light is on 2 Adjust the angle of view CDAdjust the field angle Move the zoom adjustment switch in the TELE or WIDE direction to adjust the field angle Adjust the focus Move the focus adjustment switch in the NEAR or FAR direction to adjust the focus NOTE When the ZOOM FOCUS switch is set to either TELE WIDE or NEAR FAR the iris will automatically open up for about 30 seconds and focus can be easily adjusted During this interval the electronic shutter mode is activated and the image may flicker However this is not a malfunction U mO RESET SPOT TAOTDON ALARM NM eT UE 3 Press the MEMORY button for 2 seconds or longer The ALARM POSITION indicator light blinks for 3 times green 4 Adjust the brightness This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side NOTE e For adjusting the brightness do not conduct it
42. vention wire is not included Connect the video signal cable r pg 14 Lower the cover and connect the connectors Upon connecting cover the connectors using the protection cover Connect the input power supply cable pg 16 Connect the alarm cable TK C215V12 only pg 15 Wrap insulation tape around cables Insert the camera unit into the ceiling hole E Alarm signal cable TK C215V12 only 3 4 Solder or crimp 6 wire l Protection cover 1 Insulation tape Wrap with tape Input power supply cable TK C215V12 is used in the above illustration Align with shooting direction E Mounting 1 Align with the shooting direction when mounting the camera 2 Fasten the camera x3 locations D Press the screw head of the ceiling mount bracket all the way in using a cross screwdriver 2 With the screw pressed in using the screwdriver turn about 90 in the clockwise direction followed by pulling out the screwdriver 3 The ceiling mount bracket is attached to the ceiling and the camera fastened NOTE Dismantle the camera upon turning the screw heads of the ceiling mount bracket x3 by 90 in the counterclockwise direction 07 Upon HShd TK C215V4 is used in the above illustration E Adjusting Images After mounting is completed adjust the images while checking the act
Download Pdf Manuals
Related Search