JMR electronic 1U SCSI JBOD Network Card User Manual
Contents
1. 1 Introduction The 4 bay StorBlade 1U SCSI JBOD enclosure is designed for use with a host system to provide a high end storage solution The following is a summary of the 4 bay 1U enclosure features The 4 bay StorBlade 1U SCSI JBOD Rackmount enclosure is a four drive enclosure that supports up to four 3 5 LP Low Profile SCA 80 pin drives It supports single ended Ultra2 SCSI and Ultra 160 SCSI The SCSI enclosure has two SE LVD single ended Low Voltage Differential Channels 2 4 6 8 10 12 15 bay Product Family Features FORTRA and StorBlade are families of high end enclosures designed for high volume performance storage solutions The following table shows the features of the FORTRA 2 4 6 8 10 12 15 bay and the StorBlade products 2 bay 4 bayl 6 bay 13 8 bay 10 bay 1 12 bay 15 bay l3 StorBlade PO g gt oo Number of Device Bays Number of Blowers umber of Power Supplies Number of I O Channels SCSI Only SCSI SE LVD Supported ibre Channel Supported ot Swap Canisters emovable Power Supplies Removable Blowers N 1 Power Supplies N 1 Blowers MIA Support FC Only Loop Expansion Support FC Only Daisy Chainable SCSI Only Built in Termination SCSI Only Auto Termination SCSI Only AF TE SES Ready Optional SAF TE SES Compatible SCSI to SCSI RAID Support ibre to SCSI RAID Support ibre to Fibre RAID Support ibre to ATA RAID Support SCSI to ATA RAID Support D esktop T ower R ackmou2. 5V 20A 12V 6A Blower Quantity 2 Size 70mm 2 75 each Air Flow 11 3CFM 0 32m min each Noise 38dB A SCSI Features Daisy Chaining StorBlade SCSI enclosures include a SCSI I O OUT port to allow additional devices and enclosures to be daisy chained easily onto the bus The limit of devices and enclosures that can be added is only regulated by the maximum cable length and maximum number of devices as specified by the SCSI standard For specific connection and installation information refer to Chapter 4 ID Selection 0 15 device ID addresses are addressable in SCSI wide configurations and can be easily set up via ID Jumpers for each slot located on the I O module For specific connection and installation information refer to Chapter 4 StorBlade SCSI JBOD Installation Guide Rev A 2 Hardware Specification This chapter covers specification information for the 4 bay StorBlade enclosures The following matrix describes the identification codes for the available configurations for all FORTRA and the StorBlade enclosures FRXXXL21X2XXXXX SINGLE DUAL CONTROLLER S Single Controller D Dual Controller BACKPLANE TYPE 1 Gigabit Backplane 2 2 Gigabit Backplane CONTROLLER MANUFACTURER MODEL INTERFACE None Blank if at the end of P N H1 Chaparral G5312 LVD Host LVD Drives H2 Chaparral G7313 Fibre Host LVD Drives H3 Chaparral K5312 LVD Host LVD Drives H4 Chaparral K7313 Fibre Host
3. LVD Drives H5 Chaparral JSS122 LVD Host LVD Drives H6 Chaparral JFS124 Fibre Host LVD Drives H8 Chaparral JFS224 Fibre Host LVD Drives FZ Microtest FileZerver Network Attached Ethernet LVD Drives 12 Infortrend Sentinel 2500 50 LVD Host LVD Drives Infortrend Sentinel 2500 50 w IFT9282F Fibre Host LVD Drives 13 Infortrend EonRAID 2500 50 w IFT9288B6B Fibre Host LVD Drives 14 Infortrend EonRAID 5251F 2G Fibre Host 2G Fibre Drives 15 Infortrend SentinelRAID 150 LVD Host LVD Drives IS Infortrend EonRAID 7250 12U3D SCSI Host ATA Drives IF Infortrend EonRAID 7250 12F2D Fibre Host ATA Drives M3 Mylex DAC FFx 1G Fibre Host 1G Fibre Drives M5 Mylex DAC FFx2 2G Fibre Host 2G Fibre Drives SAF TE SES None Blank if at the end of P N S SAF TE SES POWER SUPPLY QUANTITY A number Equal to Power Supplies in Enclosure AC or DC POWER SUPPLY AC Power Supply D DC Power Supply COLOR CANISTER ACCENT 1 Silver Opal 2 Black Black 3 Silver Black 4 Blue Blue DRIVE I O SCSI CHANNELS or FIBRE LOOPS A Number Equal to Drive I O Channels ENCLOSURE I O L SCSI 3 Ultra 160 LVD SE Multimode Fast Wide HD68 F 1 or 2Gb s Fibre Channel A ATA FIBRE GBIC READY No GBIC Slots G GBIC Ready u s Power cords Included NUMBER OF DRIVES For International Models Drives 02 04 06 08 10 12 15 Add Power Cord FAMILY SERIES Australia CBL 00602 FR Fortra Rackmount Europe CBL 00525 FT F
4. the information in this manual is accurate and complete However JMR shall not be liable for any technical or editorial errors or omissions made herein or for incidental special or consequential damage of whatsoever nature resulting from the furnishing of this manual or operation and performance of equipment with this manual Disclaimer The original product packaging has been tested and is safe under normal shipping circumstances Reshipping the product without using the original product packaging will void the warranty Do not ship the unit with canisters or power supplies installed as this will void the warranty and could cause damage to the unit and drives The canisters should be packaged separately within the product packaging as provided FCC Information The FORTRA and StorBlade equipment generates uses and can radiate radio frequency energy If the FORTRA or StorBlade Array is not installed and used properly that is in strict compliance with these instructions it may cause interference to radio and television reception The FORTRA and StorBlade equipment and its contents are designed to comply with the limits for a Class A computing device in accordance with the specifications in Part 15 of FCC rules These rules are designed to provide reasonable protection against radio interference in a commercial installation However there is no guarantee that interference will not occur in a particular installation Operation of this equip
5. Initial Release StorBlade SCS JBOD Installation Guide Rev A Appendix A Drive and Controller Manufacturers Drive Manufacturers Fujitsu Internet Address www fcpa com Hitachi Internet Address www hitachi com IBM International Business Machines Corporation Internet Address www ibm com Maxtor Internet Address www maxtor com Seagate Technology Internet Address www seagate com RAID Controller Manufacturers Adaptec Inc Internet Address www adaptec com Chaparral Network Storage Internet Address www chaparralnet com Digi Data Corporation Internet Address www digidata com Infortrend Corporation Internet Address www infortrend com Intel ICP VORTEX Intelligent Computer Peripherals Internet Address www icp vortex com Mylex Corporation Internet Address www mylex com Silicon Image CMD Storage Systems Internet Address www cmd com StorBlade SCSI JBOD Installation Guide Rev A StorBlade Host Bus Adapter Manufacturers Adaptec Inc Internet Address www adaptec com Antares Microsystems Internet Address www antares com Emulex Corporation Internet Address www emulex com JNI Corporation Internet Address www jni com QLogic Corp Internet Address www glogic com StorBlade SCSI JBOD Installation Guide Rev A
6. Removal Insertion In the 1U04 SCSI JBOD enclosure the power supply is not a field replaceable unit FRU Therefore if you have a power supply malfunction contact Technical Support at JMR Electronics See Chapter 7 for contact information Blower Removal Insertion In the 1U04 SCSI JBOD enclosure there are two blowers that are not field replaceable units If a blower malfunction occurs please contact JMR Electronics See Chapter 7 for contact information StorBlade SCSI JBOD Installation Guide Rev A 6 1U04 Cabinet Installation This chapter covers the installation of the Rackmount enclosure into a standard 19 483mm wide and 30 762mm to 36 914mm deep cabinet that meets the EMA RETMA standards Before beginning rail installation please take note of the following precautions StorBlade SCSI JBOD Installation Guide Rev A StorBlade Rail Mounting Kit Hardware Eight 10 32 Screws wa O Four each 8 32 Screws Washers Nuts o Spare Hardware Parts Check with a JMR Sales Representative for pricing and availability of spare hardware parts Description JMR Part Number 410 32 Screw HDS 01580 8 32 Screw HDS 00350 8 32 Nut HDN 00040 8 32 Washer HDW 00080 Rail Installation Expansion Rail 1 Affix the extension brackets to the main rail using the 8 32 screw washer nut assemblies Adjust to the correct length for the cabinet depth being used Front of Rackm
7. StorBlade 1U SCSI JBOD 4 bay Rackmount Enclosure Installation Guide October 3 2002 Revision A Patent Pending IM StorBlade Copyright Copyright 1998 1999 2001 by JMR Electronics Inc All Rights Reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means electronic mechanical photocopying recording or otherwise without the express written permission of JMR Electronics Inc Sales and Ordering Information JMR Electronics Inc 20400 Plummer Street Chatsworth CA 91311 USA Phone 818 993 4801 Fax 818 993 9173 Office Hours Monday Friday 8 00 A M to 5 00 P M Pacific Standard Time European Corporate Headquarters JMR Electronics United Kingdom Tain Pickthall P O Box 3058 Wokingham Berkshire RG40 3FU United Kingdom Phone 44 118 973 6018 Fax 44 118 973 7191 E Mail Iain jmr com Internet http www mr com Trademarks JMR the JMR logo and FORTRA and StorBlade are registered trademarks of JMR Electronics Inc All other product and brand names are the property of their respective holders Changes The material in this document is for information only and is subject to change without notice JMR Electronics Inc reserves the right to make changes to this manual and the equipment described herein without notice JMR has made all reasonable efforts to ensure that
8. ereu arde dU eed NUN OD A R DU seus a 2 3 Rotation Vibration Specifications 2 3 Fault Indication Features o nd bs dde YD AUU AU OD AYN AG 2 3 Fault Indicios 442 dere eas ai ts SSRs e t u 2 3 Audible ALC re dada 2 3 3 Device Installation SCA Connection and Hot SWapping 3 1 Canister Removal Insertion 3 1 Drive Installation 55335654 sandede ge te diver na di ii 3 1 4 SCSI Setup Basic Personality Caed Setup tii aid 4 1 A 4 2 Available DS id sd 4 2 TIS COMEICE ora dd FA EDD 4 3 Front Status LEDS ii bee aaa a a 4 3 External VO Connection FFF yaa FFF uy 4 3 Terminauon iu 2 arsa usu a a Yd Ud 4 4 Daisy Choinmg io uawan DY FU rdd Y WCH BAN SW dB 4 4 SCSTACCESSONES iu ua Gu Dd ace OU AF EA O hops FA MG d 4 4 5 Power Supply and Blowers Power Supply Removal Insertion 5 1 Blower Removal Insertion 5 1 StorBlade SCSI JBOD Installation Guide Rev A StorBlade 6 1U04 Cabinet Installation Rail Mounting Kit Hardware Spare Hardware Parts Rail Installation 7 Product Support US Corporate Headquarters Manual Changes Appendix A Drive and Controller Manufacturers Drive Manufacturers ccc ec cee ccc eee uu RAID Controller Manufacturers Host Bus Adapter Manufacturers StorBlade SCSI JBOD Installation Guide Rev A
9. ght on a single canister indicates a device fault External I O Connection The external I O connections are located on the back of the unit The figure below shows the external I O connections available AC Inlet SCSI A SCSI A SCSIB SCSI B StorBlade SCSI JBOD Installation Guide Rev A StorBlade The SCSI In ports are used to connect to a host and require an external cable with a 68 pin High Density male connector to mate at the enclosure side Cables are not included Each SCSI channel must use a separate external cable connection from the rackmount to the host adapter or RAID controller It is important that the external cable length and impedance is taken into consideration and is adequate for the devices and SCSI speeds being used JMR carries its own line of high quality external SCSI Cables Termination Termination must be provided at the end and beginnings of each SCSI bus either internally or externally Drive level termination is not recommended since the terminated device may be easily removed Termination is not automatic and the Channel A OUT and Channel B OUT connections must have LVD SE termination if not used Daisy Chaining SCSI I O Out ports are used to add other enclosures and devices to the SCSI bus SCSI I O Out ports require a cable with a 68 pin High Density male connector to mate When daisy chaining the SCSI I O Out port of the enclosure is connected to the SCSI I O In port of the enclosu
10. ieser Komponenten f hren und somit den Garantieanspruch gefahrden Packaging complies with ISTA International Safe Transit Association standards and has been ISTA certified Each canister is pre packaged in an anti static bag Do not throw the packaging away if the product is intended for re shipping When transporting or shipping a JMR approved shipping container must be used Disclaimer The original product packaging has been tested and is safe under normal shipping circumstances Reshipping the product without using the original product packaging will void the warranty Do not ship the unit with canisters and or power supplies installed in the enclosure as this will void the warranty and could cause damage to the unit and drives The canisters should be packaged separately within the product packaging as provided StorBlade SCSI JBOD Installation Guide Rev A StorBlade Thermal Specifications StorBlade enclosures have been designed to meet the air flow cooling requirements for popular 7 200 10 000 and 15 000 RPM disk drives Using a high performance blower air is pulled in from all open vents and exhausted out the back of the unit Rotation Vibration Specifications StorBlade enclosures have been designed to meet the rotation vibration shock requirements for popular 7 200 10 000 and 15 000 RPM disk drives Fault Indication Features This section reviews the indicators that will notify the user of a power su
11. jumpers on the personality card W1 W2 W3 and W4 for hard setting the ID of each slot Header W1 is for slot 3 Header W2 is for slot 2 Header W3 is for slot 1 Header W4 is for slot 0 Switch settings are shown from the rear of the unit Available ID s Each bus is allowed to have ID s that range from 0 15 No two devices on the same bus may share the same ID Each host controller always uses one ID The Figure above shows all 0 15 possible ID settings StorBlade SCSI JBOD Installation Guide Rev A StorBlade ID Conflict When two devices share the same SCSI ID a conflict occurs This conflict must be corrected before the SCSI bus will work properly If a conflict occurs check all jumper settings to ensure that no devices on the bus share the same ID Also check all other devices on the bus outside of the enclosure Front Status LEDs A status indicator is located on each canister A Blue light indicates normal drive activity A Red light indicates a device fault If all canisters display a Red light that is blinking on and off it indicates that there is a system fault A system fault is either a power supply or blower failure The power supply and blowers are not field replaceable units A fault with either the power supply or blowers will require replacement of the entire unit Refer to Chapter 5 Drive Status Indicators Sa A blue light on a single canister indicates device activity or busy e A red li
12. ment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures are necessary to correct the interference WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to use the equipment WARNUNG Nicht ausdriicklich durch den Hersteller genehmigte Anderungen oder Modifikationen k nnen die Erlaubnis Zur benutzung der Produkte gefahrden You may find the FCC booklet How to Identify and Resolve Radio Interference Problems helpful This booklet is available from the U S Government Printing Office Washington DC 20402 Stock 004 000 00345 4 Printed in the USA Part Number PUB 00286 Revision A October 2002 SCS Patent Pending StorBlade SCSI JBOD Installation Guide Rev A StorBlade Table of Contents 1 Introduction 2 4 6 8 10 12 15 bay Product Family Features 1 1 4 bay Rackmount Specifications 1 2 SCS Feat res rie e 1 2 Daisy Ch ining sig tied dias bea Roy cata tin 1 2 ID Selecione oa beads 1 2 2 Hardware Specification Environmental Specifications 2 2 Electrical Specifications diarrea ari UUN UF 4DU 2 2 Agency Compliance dr IED A A NN a 2 2 Packaging Specifications 2 2 Dis FAME os _ O A do IU Y daa eee 2 2 Thermal Specifications s
13. nt 6 10 15 bay unit features apply to both Tower and Rackmount models 1 Features are based on a standard configuration with no internal host controller s installed 2 Fibre channel 10 15 bay enclosures have built in SES 3 Fibre Channel 2Gb Model available 2Gb models use SFP transceivers m M ES lt Po lt PO Ss ss SP lt A lt ro ro ro SIKRE Sy E lt lt XP AP AJ X lt lt Fibre only Fibre Only Fibre only Y lt lt SIS SISISISIS lt lt v Y SISS lt SJ SPS SY SY S lt a SY SYS SYS s 9 ro ro lt Fibre only Fibre only Y SJ SP SP SUS SY SSU sisi SY SY SYS lt ro ro ro A lt SJ ss is sf sf s lt SS 3 TI lt StorBlade SCSI JBOD Installation Guide Rev A StorBlade StorBlade products use advanced mid plane technology developed by JMR that allows power supplies drives and all other enclosure components to interface into a single board This provides superior performance and easy connectivity The host interface supports single ended Wide Ultra2 SCSI LVD and Ultra 160 Connections to a SCSI host can be made using a 68 pin HD68 SCSI cable 4 bay Rackmount Specifications Dimensions Weight Unit Weight 35 Ibs 15 9kg Height 1 3 4 1U 44 45mm Width 19 483mm Depth 22 558 8mm Power Supply Quantity 1 Power 200 Watts Input 100 240 VAC 50 60Hz Output 3 3V 14A
14. ortra Tower UK CBL 00677 1U StorBlade Rackmount StorBlade SCS JBOD Installation Guide Rev A StorBlade Environmental Specifications Operating Temperature 5 C to 40 C 41 F to 104 F Storage Temperature 0 C to 65 C 32 F to 149 F Maximum ambient temperature is dependent on the recommended temperature to meet the MTBF rating as specified by the manufacturer of the installed devices Electrical Specifications AC Inlet Type 1EC320 EN60320 Power Cord NEMAS 15P Power Supply Auto switching for 110 220V operation Agency Compliance StorBlade enclosures have been designed and built to comply with the FCC Class A UL CSA TUV CE and C Tick standards For more information on FCC Class A compliance see page 2 Packaging Specifications StorBlade packaging has been designed to be reusable and recyclable Drives may be installed and shipped in the canisters as long as the canisters are in their original packaging location and are not installed in the enclosure Shipping the unit with canisters and or power supplies installed in the enclosure may cause damage to the enclosure or to the drives and will void the warranty SAFETY TIP Reshipping the enclosure with canisters drives or power supplies installed in the enclosure may cause damage to these components and will void the warranty SICHERHEITSHINWEIS Der Versand des Geh uses mit eingebauten Einsch ben Platten und Netzteilen kann zur Besch digung d
15. ount Unit Two 8 32 Screws Washers Nuts StorBlade SCSI JBOD Installation Guide Rev A StorBlade 2 Affix the extension bracket to the rear of the unit using two 10 32 screws There are 3 holes in the extension bracket for mounting Depending on the hole pattern that is being used in the cabinet two holes should always be available for securing the extension bracket 3 The fronts of the rails have three holes Two of the holes top and bottom are used to secure the rail to the cabinet The middle hole is used to secure the enclosure to the rail and cabinet Secure the front of each rail to the cabinet vertical rails using two 10 32 screws for each rail 4 Slide the unit into the cabinet and secure it to the cabinet by tightening the two embedded thumb screws StorBlade SCSI JBOD Installation Guide Rev A 7 Product Support For current information on this product including updates to the manual and technical support related issues please contact the sales support section of our web page at www jmr com or you can contact our Technical Support division directly at the address below US Corporate Headquarters JMR Electronics Inc ATTN Technical Support Division 20400 Plummer St Chatsworth CA 91311 Customer Support 818 739 1140 E mail techsupport jmr com Office Hours Monday Friday 8 00 A M to 5 00 P M Pacific Standard Time Internet http www jmr com Manual Changes Revision A
16. per connection for grounding The AC power cables included with the unit have three prongs one of which is used for the ground connection Do not use a two prong AC cable with the unit since this will not allow for proper unit grounding and could cause problems with normal unit operation WARNUNG Bei der Verbindung der Unit mit einer Steckdose oder einer Verteilerdose sollten sie auf eine korrekte Erdung derselben achten Die mitgelieferten Kaltger teanschluBkabel habe 3 Kontakte von denen einer zur Erdung verwendet wird Verwenden Sie kein Stromkabel mit 2 Anschl ssen da dieses keine korrekte Erdung erm glicht und Probleme w hrend des regul ren Betriebs verursachen kann Basic Personality Card Setup This section covers 4 bay 1U SCSI JBOD units using the basic personality card This card does not have a controller interface built in The following Figure shows the slot numbering sequence used to refer to device bays and additionally shows the factory ID value for each slot Slots 0 1 are on Channel A and Slots 2 3 are on Channel B Slot 3 ID 3 Slot 2 ID 2 Slot 1 ID 1 Slot 0 ID O StorBlade SCSI JBOD Installation Guide Rev A StorBlade Setting ID The basic personality card has jumpers available on the personality card to set the ID for each slot To access the jumpers the top cover must be removed The following picture indicates the location of jumpers W1 W4 NOTE View is from rear of the unit There are 4
17. pply or blower that is in a fault state More information is available in Chapter 5_ power supply and blowers Fault Indicators All slots will blink Red in color on a blower fault On a power supply fault the front power supply LED will blink on and off Audible Alert On a blower or power supply fault an audible alert will sound StorBlade SCSI JBOD Installation Guide Rev A 3 Device Installation This chapter covers SCSI device installation for 4 bay 1U rackmount enclosures SCA Connection and Hot Swapping The unit uses SCA 2 type connectors which provide a safe means of connection disconnection when hot swapping devices In order to utilize this feature the host adapter or RAID controller and host operating software must support the feature Any SCA drive is capable of plugging directly into the backplane of the unit and should not require any additional cabling or connections Canister Removal Insertion 1 Pull the handle out to unlock the canister from the StorBlade unit Notice that the locking tab slides down as the handle is pulled out 2 Pull the canister straight out to remove Ensure that any installed devices are spun down before full removal to prevent damage to the drive Follow the steps in reverse to reinstall SAFETY TIP After disengaging a device from the enclosure allow 10 seconds before pulling the canister out of the unit This allows the device to properly spin shut down before transpor
18. re or device being added Ensure that when new devices are added to the SCSI bus that the ID does not have a conflict Once the units are connected together termination must be moved to the last device or enclosure on the SCSI bus The devices or enclosures daisy chained together must be compatible SCSI devices Single ended interface devices cannot be on the same daisy chained bus with differential interface devices Up to 16 devices including the host may be daisy chained together on the same bus SCSI Accessories JMR carries its own line of external StorBlade compatible SCSI SE and LVD terminators The following Table lists JMR part numbers and descriptions Please contact a JMR representative for current availability and pricing JMR SCSI TERMINATORS JMR Part Ends Connector Type Terminator Type CNA 01883 Molded SCSI 3 68 pin SE LVD Multimode StorBlade SCSI JBOD Installation Guide Rev A StorBlade JMR carries its own line of high quality external StorBlade compatible SCSI cables The following Table lists JMR part numbers and descriptions Please contact a JMR representative for current availability and pricing JMR SCSI CABLES JMR Part Ends Connector Type Length FT CBL 00532 Molded SCSI 3 to SCSI 3 3 CBL 00534 Molded SCSI 3 to SCSI 3 6 StorBlade SCSI JBOD Installation Guide Rev A 5 Power Supply and Blowers This section covers operation of the power supply and blowers Power Supply
19. t Drive Installation Front Handle 1 After removing the canister place it on a static free surface along with the device to be installed StorBlade SCSI JBOD Installation Guide Rev A StorBlade 2 Place the device in the canister with the four screw holes aligned with the holes in the device Mount the drive by using the screws included with the unit use all 4 screws to mount the drive 3 Replace the canister into the unit 4 Repeat steps 1 through 3 until all devices are installed 5 Configure ID and other options as required 6 Establish host connection StorBlade SCSI JBOD Installation Guide Rev A 4 SCSI Setup This chapter covers SCSI device setup and option settings Please take note of the installation warnings below before beginning setup WARNING Take care when connecting the unit to an AC power source to ensure that it is plugged in to a circuit of the appropriate rating 110v or 220v For safe operation the circuit should have over current protection to prevent damage to the unit in the event of circuit overloading WARNUNG Vergewissern Sie sich da die Netzspannung 220V 110V korrekt eingestellt ist bevor Sie das Ger t mit dem Stromnetz verbinden Zur Sicherheit sollte das Netz ber einen Uberspannungsschutz zur Vermeidung von Sch den im Falle einer Uberlast verf gen WARNING When connecting the unit to an AC outlet or power strip ensure that the outlet has the pro
Download Pdf Manuals
Related Search