JBL GTQ240 Stereo Amplifier User Manual
Contents
1. Wall bracket for The Source Remote with battery FM and AM antennas one Speaker Placement Satellites Subwoofer Surround Speakers L aO Mounting Options Satellites and Surrounds Mm On shelves Mounting to Wall On the wall Optional brackets WB300 Using optional wall mount brackets 1 Attach plate to wall The customer is responsible for proper selection and use of mounting hardware available through hardware stores to properly and safely wall mount the speakers Q 2 Slide speaker onto support On optional stands FS300 R G 3 Place speaker and support on wall plate Remote Control Battery Installation V ol J lt _ Push small tab towards battery slot and pull battery drawer out Remove old battery uon Insert new battery with side up and slide battery drawer back into remote two Connections Connect TV or VCR to The Source TV or Hi Fi VCR Rear Panel of The Source AUDIO OUT 2 8 OD a P x e JBL ESC350 Out In B Tuner MV Frequency Powered Subwoofer Tape Aux TV Standard Antenna Note The Source also provides a stereo mini jack B to provide an easy connection to devices that2. on the remote Turn volume control control on The Source counter clockwise or Mute To lower volume completely Push Mute on the remote control When Mute is pushed again the volume will return to its original level Mute REMOTE Q Bass Bass Treble Surround Mode C Surround Calibrate THE SOURCE To raise the bass level Push on The Source or REMOTE push Calibrate on the remote control until Bass illuminates in The Source display Push until you reach the desired level Bass Treble Surround Mode C Surround Calibrate THE SOURCE To lower the bass level Push on The Source or REMOTE push Calibrate on the remote control until Bass illuminates in The Source display Push until you reach the desired level Treble Treble Or C Surround Calibrate THE SOURCE To raise the treble level Push on The Source or REMOTE push Calibrate on the remote control until Treble illuminates in The Source display Push until you reach the desired level Treble O C Surround Calibrate THE SOURCE To lower the treble level Push on The Source or REMOTE push Calibrate on the remote control until Treble illuminates in The Source display Push until you reach the desired level CD Oper
3. simply Cinema ESC350 simple setup guide Table of Contents Important Safety Precautions 44 awawscaaweeteceengw Re macie Rorate grew 3 1 Speaker Placement sido di eR SUUS ROUES geval oae s eA Y RU ee ERES 4 Mounting Options 4 cebat Rc REN TN E SO RU Ca ace aca a wae ES 5 Remote Control Battery Installation llle 5 2 CONMECHONS usce ER Uma cx e RUE RUE HR CRLE gle Wie wale we ated a ecd e Re dis 6 Connect TV or VCR to The Source ee eh 6 Connect Antennas to The Source l lille 6 Connect Optional Cassette Deck to The Source llle 6 Connect The Source to a Subwoofer llle 6 Speaker Connection Tips sax mee Wed bea eS RARE we XC HUC E eR S 7 3 Operations TETTE See Berar a wee Dal ae eo Ba ae Ba ed 8 lI epa Geb Sac aw de dae he ew ee De Dawe SE Rea eae ee ae eS 8 cr ee fo Rees lesen ayes Uae ania lero Bil Behe fc a E aus fine Briss Ba 8 R Bass umo odie pcs fa mace tice ote seit e Gi US IE anes Bie BATUR o a e te B ane 4 9 thank you far topaig JBL Fortigi Ud rrr 9 than 50 years JBL has been involved in every CDOperaion eeina eane ee i a Para OTT TO T LL EEE D S 10 aspect of music and film recording and repro To Play du D o uia maa tg ari UE OR don d S era apace 4 Dd aS EE 10 duction from live performances to monitoring To Skip to a Different Track ue ek REA RE RE TEES RR E 10 i To Scan within the Same Track iocis e ER 454545 0445880 ER 10 the recordings you play in your
4. Auto Tune on Then when you push lt lt the remote control the The Source or gt gt on The Source or tuner will automatically advance to the next station with a strong signal Preset Operation The Source Remote Control Power Sleep Mute o EF i Power Volume Om On 88 O er OOO00 Tone Calibrate E3Ni jly Cinema o AM FM v Tape Aux oe Random Repeat Auto Tune Stereo Mono Rear Speakers Bas Surround Mode Treble Tuner Presets Auto Add Delete 2445 Tuner Presets Auto Add O Delete Tuner Presets Auto Add Delete THE SOURCE 1 Tune to the station that you want to add into memory 2 Push Add on The Source That station is now added to your selection of stations in memory THE SOURCE 3 To delete a preset Push Delete on The Source That station is now removed from your selection of stations in memory 6 6 Search le Tun Pll Om Oy G6 O 860 THE SOURCE 4 To skip between preset stations Push I lt or gt on The Source or The Source has a unique feature that will automati cally place up to 32 stations in memory To activate this feature push and hold the Auto button for one second The tuner will search the dial
5. and place the stations with a strong signal into memory REMOTE the remote control Note Activating this feature will delete all stations that Tuner Presets were previously stored in memory To prevent this from Auto Add O accidentally occurring the Auto button will only activate if held for a full second Delete THE SOURCE Surround Mode Operation Remote Control Power Sleep Mute Q O O Oy G6 O OOO0 Tone Calibrate Exi Cinema AM FM Repeat v Auto Tune Tape Aux Stereo Mono The Source Power Volume Q ILI TII tb Random Rear Speakers et Bass Treble Surround Mode Tuner Presets Aio Ad Delete siis What is Dolby Pro Logic Dolby Pro Logic is an encode decode process by which four channels of sound track information are encoded into two channels for playback on VCRs laser disc players and some TV broadcasts and then decoded back into four channels for playback through five loudspeakers Remember that a Dolby Pro Logic system consists of three channels of information for front left center and right speakers and one channel of mono surround This system contains three surround modes 1 Dolby Pro Logic In this mode all five speakers are used 2 Dolby Pro Logic Phantom In this mode the center
6. channel does not operate This may be preferred when listening to a music source that was not recorded with surround channel information information The surround channel is played back through two speakers Dolby Pro Logic helps to re create all of the impact and excitement of a movie theater in your home 3 2 channel In this mode the program is played back in a tra ditional stereo form Rear Speakers Om m 9 see QT HUE Tone Calibrate Tape Aux Stereo Mono O Rear Speakers THE SOURCE To switch between the three surround modes Push Surround Mode on The Source or REMOTE the remote control THE SOURCE If you are listening to a program in the Dolby Pro Logic Normal or Phantom mode and you wish to turn off the surround speakers Push Rear Speakers on The Source Test Tone The Source Power Remote Control Power Sleep O O UBL Mute Volume era Open O OO 9 AM FM O cD Random O Ge O o ANM Repeat Or 9 O O W AutoTune DT O Tape Aux Stereo Hono eeoo0 O Q Tone Calibrate speakers at mee Tuner Presets EXNi jly Cinema O f 2G w m Oe 19 CO sura e 000 Tone Calibrate For proper Dolby Pro Logic operation a test tone is used to calibrate the volume settings of the speakers A noise will be THE SOURCE Usi
7. or sound is very low check the following Check all connections between the amplifier and each of the speakers Raise the surround volume from the remote control see Operation section Make sure the TV show or movie you are watching is recorded in Dolby Surround If there is no sound from the center speaker check the following Make sure that the processor is in the Pro Logic mode If it is in Phantom or Stereo mode the center speaker will not play Check the connections between the subwoofer and the center speaker If you have low bass output check the following Experiment with placement of the subwoofer Remember place the subwoofer in a corner to get maximum bass output from the system Increase the level of bass using the remote control Adjust the level control on the rear of the subwoofer If you are having trouble picking up radio stations check the following Make sure the antenna is hooked up properly Depending on your distance from the station s transmitter you may need to install an FM antenna on the roof or in the attic 248 Specifications Components The Source surround sound processor CD player AM FM tuner Subwoofer 8 driver in a bass reflex enclosure Satellite Speakers 3 4 tweeters 3 midrange driver System Remote credit card sized hand held controller ESC350 System Amplifier 200 watts total system output front channels 3
8. 5 watts x 3 1 THD surround channels 15 watts x 2 1 THD subwoofer 65 watts x 1 1 THD System Frequency Response 6dB 35Hz 20kHz Signal to Noise Ratio 90dB Input Impedance 20k ohms Input Sensitivity 250mV The Source Dimensions H x W x D 4 5 8 x 10 1 4 x 9 3 4 inches 117 x 260 x 248mm Weight 5 lbs 2 3 kg Subwoofer Dimensions H x W x D 15 1 8 x 13 x 14 1 2 inches 384 x 330 x 368mm Weight 34 5 lbs 15 7 kg Satellites Dimensions H x W x D 4 3 8 x 3 3 16 x 3 3 4 inches 111 x 81 x 95mm Weight 8 lbs 4 kg System Remote Dimensions H x W x D 4 7 8 x 2 1 4 x 1 4 inches 124 x 57 x 6mm Weight 25 bs 11 kg Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated 219 UBL JBL Consumer Products 250 Crossways Park Drive Woodbury NY 11797 8500 Balboa Boulevard Northridge CA 91329 1 800 336 4JBL 4525 USA only www jbl com 1998 JBL Incorporated JBL and Simply Cinema are registered trademarks of JBL Incorporated Trademarks of Dolby Laboratories 8 98 amp Part No ESC3500M H A Harman International Company
9. Channel Volume aa iana eee Ie 16 that meet their needs and expectations Delay Times 2 vara dora EROR AGNI Gs ee GA ew done PSU PS 17 THOWDIESMOOEING PPP 18 JBL Consumer Products Specifications A MCN r 19 read first Important Safety Precautions RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To prevent electric shock do not remove the grounding plug on the power cord or use any plug or extension cord that does not have a grounding plug provided Make certain that the AC outlet is properly grounded Do not use an adapter plug with this product The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 1 Read Instructions All the safety and operating instruc tions should be read before the product is operated 2 Retain Instructions The safety and operating instruc tions should be retained for future reference 3 Heed Warnings All warn ings on the product and in the operating instructions should be adhered to 4 Follow Instructions All operating and
10. Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 20 Servicing Do not attempt to service this product your self as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 21 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a The power supply cord or the plug has been damaged or b Objects have fallen onto or liquid has been spilled into the product or c The product has been exposed to rain or water or d The product does not oper ate normally when following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation or e The product has been dropped or damaged in any way or Figure 1 Example of Antenna Grounding as UE p H per National Electrical Code ANSI NFPA 70 g g f The product exhibits a dis tinct change in performance this indicates a need for service 22 Replacement Parts When replacement pa
11. REMOTE Push Calibrate on the Push on the remote Push on the remote remote control until Delay control to increase the control to decrease the appears in the display and delay time delay time the corresponding LED on top of the display is lit EXPE Troubleshooting If there is no sound from any of the speakers check the following Make sure the subwoofer is plugged into an active AC wall outlet Make sure the Master Power Switch located on the rear of the subwoofer is in the On Standby position Make sure there is a source for example a VCR or television hooked up to the TV or tape aux input jacks on The Source Make sure that the program material is playing Recheck the hookup connec tions If most of the sound comes from the center channel speaker with little or no information from the surround channels note the following Although most of today s televi sions are equipped with stereo audio output jacks some stereo televisions have poor audio sec tions and are unable to provide a Dolby Pro Logic encoded signal In the unlikely event that you experi ence this problem connecting the audio outputs from your hi fi VCR laser disc player DVD player or satellite receiver directly to one of the inputs on The Source will pro vide a proper audio signal and allow you to enjoy true Dolby Pro Logic surround sound If there is no sound from the surround speakers
12. a Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable sys tem is grounded so as to pro vide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides infor mation with regard to proper grounding of the mast and supporting structure ground ing of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding elec trodes and requirements for the grounding electrode See Figure 1 16 Lightning For added pro tection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 17 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 18 Overloading Do not over load wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 19 Object and
13. ace This product should not be placed in a built in instal lation such as a bookcase or rack unless proper ventilation is provided or the manufactur er s instructions have been adhered to 11 Power Sources This prod uct should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 12 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 13 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying par ticular attention to cords at plugs convenience recepta cles and the point where they exit from the product 14 Nonuse Periods The power cord of the product should be unplugged from the outlet when left unused for long periods of time 15 Outdoor Antenn
14. ation Remote Control Power Sleep Mute Or OG Ou 606 Oy ee O ee on O00009 Tone Calibrate Exi Cima Tape Aux Stereo Mono Rear Speakers eee e Surround Mode Treble Tuner Presets Kato Add O Delete The Source Power Q T pm D Random s To Play a CD e Or 6 9 O 60 m 5 O Surround THE SOURCE THE SOURCE REMOTE 1 Push Power and or Open on The Source 2 Insert CD 3 Push Play on The Source or To Skip to a Different Track ko c Rn 6 6 Search Tune THE SOURCE Push I lt or gt I on The Source or REMOTE the remote control until the number of the desired track appears on the display To Scan within the Same Track O O Search Tune On Oy ee Ou 89 THE SOURCE Push lt lt or gt gt on The Source or REMOTE the remote control the remote control The door will close automatically To Pause the CD C3 o Q COT ae Ox e 9 Q Surround THE SOURCE Push Pause on The Source or To Stop the CD Search Tune THE SOURCE Push Stop on The Source or To Program the CD REMOTE the remote control Push again to r
15. channel e oO Calibrate C Surround OO Calibrate C surround O e o Calibrate REMOTE Push Calibrate on the remote control until Rear appears in the display and the corresponding LED on top of the display is lit REMOTE Push on the remote control to increase the volume of the rear channels REMOTE Push on the remote control to decrease the volume of the rear channels Delay Time The delay control allows The best setting will the distance between the the user to set the sur depend on the distance main listening area and round delay between 15 between the main the rear speakers The chart The Source and 30 milliseconds in listening area and the at the bottom shows the one millisecond increments front speakers as well as recommended settings 2 Remote Control 9 wo Power Sleep a OQ 2 gt 68 18 O CJ AM FM e co Or Q6 2 OQ OLIO 9 PHP E o eo O3 eue E eo Ol Pes Tape Aux Stereo M ce ceeeo OQ S Tone Calibrate speakers Bas Treble Tuner Presets 9 T EMi yly Cinema OQ Q 000 QQ A O O B mc Delete 0 5 10 15 20 25 30 35 40 Distance in feet From Front Speakers C Preferable Acceptable O Surround O Surround O Surround 0000 O O e Calibrate Calibrate Calibrate REMOTE REMOTE
16. emote Control Power Sleep Mute Q OF pen 58 o Q um e D Random Or ee O e ANM Repet OQ amp e TW Auto Tune Q seen Oe 9 Tape Aux Stereo Mono OOO0G0 e Tone Calibrate speakers ms Treble Tuner Presets Engl Cinema O O76 6 QQ O Delete XT wA AM FM Repeat Power Sleep Power O e Q Was Qo Q G e AM FM 3 THE SOURCE THE SOURCE Push Power on The Source AM FM on The Source or or REMOTE the remote control THE SOURCE Push lt lt or gt gt on The Source or REMOTE the remote control To search rapidly hold down the lt lt or gt gt button If a Selected FM Station is a Little Noisy TV Auto Tune Tape Aux Stereo Mono Rear Speakers ODE Search Tune THE SOURCE Push Stereo Mono on The Source This will play the selected station without any stereo separation but there will be much less background noise Om 96 Oy ee O 8G THE SOURCE When in the Mono mode the lt lt or gt gt on The Source or REMOTE the remote control will tune up or down one frequency at a time 13 To Have the Tuner Search for the Next Strong Station AM FM Repeat TV Auto Tune Tape Aux Stereo Mono O Rear Qe Search Tune Om Oy ee O 8G Speakers THE SOURCE THE SOURCE REMOTE Push
17. esume play REMOTE the remote control Tuner Presets Auto Add O Delete THE SOURCE 1 Push Power and or Open on The Source 2 Insert CD THE SOURCE 3 Push I lt or gt I to select desired track THE SOURCE 4 Push Add to program track Repeat procedure until all desired tracks are programmed 41 To Play the Tracks of a CD in Random Order CD Random AM FM Repeat TV Oo CO OG THE SOURCE To Repeat the Disc CD Random AM FM Repeat TV e Gol 9 Tape Aux Stereo Mono THE SOURCE Push Repeat on The Source Push Random on The Source The Source will automatically delete each track it has played from the Random operation Note If Random and Repeat are both engaged the CD player will randomly play the disc deleting all played tracks until the disc is finished Tt will then randomly play the disc again Tuner Operation To Switch Between AM and FM LZ S7 AM FM Repeat TV Auto Tune Tape Aux Stereo Mono Rear THE SOURCE Push AM FM on The Source or Power Sleep eO Mute o AM FM 3 e REMOTE the remote control To Tune to a Particular Station DEO Search Tune Om 96 Oy ee O 8G The Source Power R
18. have a stereo mini jack audio output Connect Antennas to The Source FM Antenna Rear Panel of The Source AM Antenna 8 e e guo JBLESC350 Out In Ao B Tuner boe om and ee Frequency Powered Subwoofer Tape Aux TV Standard Antenna Connect Optional Cassette Deck to The Source Cassette Deck Rear Panel of The Source JBL ESC350 n Powered Subwoofer Tapey Aux TV dad Antenna Rear Panel of Subwoofer Connect The Source to a Subwoofer Rear Panel of The Source R89 US MI Europe JBL ESC350 Out In A or B az Frequency Powered Subwoofer Tape Aux TV Standard Antenna Speaker Connections Left Front Center Right Front SURROUND SPEAKERS Left Surround Right Surround Speaker and Amplifier Connection pes th ree Operations Volume The Source Volume Mute m Remote Control Power Sep THE SOURCE REMOTE To raise volume push on the remote e e Turn control on The Source control Qe 0 clockwise or Q AM FM co Random Or amp Q o o Volume pn Mute Q O O W notare one Oo m Tape Aux Stereo Mono 0ee0 Q Tone Calibrate speakers Bas Treble Tuner Presets EXNivvly Cinema 000 9 Q O O S Delete THE SOURCE REMOTE To lower volume push
19. home car or To Pause the CD iss x RR qe ene ek dere eg ERA qe a i d ne 11 office To Stop the CD scs goer many Betas qusc CRUS RA ar Bae pU Qr Au Roe 11 TO Program thenCD 25 swe iens mE pes edite qne de Semel fener ete Beha repr ia roles 11 We re confident that the JBL system you have To Play the Tracks of a CD in Random Order 2 2 2 ee ee eee ee eee 11 chosen will provide every note of enjoyment To Repeat the DISC aroas ameamua eae ohne Rim le let A Bees 4h Sie a Sterno Re 11 that you expected and that when you think T ner Operation c onde q e 02 29 087 bas cae qose QUA oe aus REA OR Aq 12 m i To Switch Between AM and FM s nbasenencsenesk asaru arat tnat ias 12 about purchasing additional audio equipment for f To Tune to a Particular Station eee ee ee ee eee 12 your home car or office you will once again If a Selected FM Station is a Little Noisy lee 13 choose JBL To Have the Tuner Search for the Next Strong Station 00 0 eee 13 Preset Operation 4 uos eure Sew RA Goa de x aoe UR Fe m dow PUR Vale naw aa ce 14 Please take a moment to complete the enclosed Surround Mode Operation 00 0 ccc cee cece IRR Rn 15 profile card It enables us to keep you posted on Test ONG i d ae GAs SAW EXZGG44de9 y WEG EE PE S ERE ER 16 our latest advancements and helps us to better Balg MCCC 16 Center Channel Volume 2 5 06 scene Re RR RE Rr RE E AERE 16 understand our customers and build products Rear
20. ng the remote control push Tone Then adjust the Center and Surround levels until the volume of all the speakers is the same during the test Note The test tone is used to calibrate the performance of the system When listening to an actual recording the volume level of the surround channels is generally much lower than that of the front channels heard cycling in order from the front left center right and both surround speakers In fact when listening to a movie virtually all of the dialogue and a substantial number of the effects are reproduced through the center channel at Balance O Surround e Calibrate oOoe Calibrate O e o Calibrate REMOTE Push Calibrate on the remote control until Balance appears in the display Center Channel Volume REMOTE Push on the remote control to adjust the balance toward the right speaker REMOTE Push on the remote control to adjust the balance toward the left speaker O Surround e o 9 Calibrate Oo Calibrate O e 0o Calibrate REMOTE Push Calibrate on the remote control until Center appears in the display and the corresponding LED on top of the display is lit Rear Channel Volume REMOTE Push on the remote control to increase the volume of the center channel REMOTE Push on the remote control to decrease the volume of the center
21. rts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same charac teristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 23 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 24 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer 25 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat Antenna Lead In Wire Ground Clamp Antenna Discharge Unit NEC Section 810 20 Grounding Conductors NEC Section 810 21 Electric Service Equipment Ground Clamps L4 Power Service Grounding Electrode System a NEC Art 250 Part H Part No JBLULB 6 96 included e e eo J i The Source Five satellites for left right center and surrounds Powered subwoofer containing all amplification Source cable LUN w i E Speaker cables 0000 ES vyly rena FM antenna AM antenna C 3 x 20 front 2 x 40 surround
22. use instructions should be followed 5 Cleaning Unplug this prod uct from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Water and Moisture Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool or the like 8 Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mount ing of the product should follow the manufacturer s instructions and should use a mounting accessory recom mended by the manufacturer 9 A Product and Cart Combination Should Be Moved with Care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 10 Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar sur f
Download Pdf Manuals
Related Search