Jasco 24922 Universal Remote User Manual
Contents
1. CS300 1 CS60 4 CS6o0 2 CAR AUDIO POWER AMPLIFIER OW NER S MANUAL Co oe 222 lt JBL E he OfficiakBrand of kive Music pp g z S INSTALLATION THANK YOU for purchasing a JBL CS Series amplifier In order that we may better serve you should you require warranty service for your new amplifier please retain your original purchase receipt and register your new JBL amplifier online at www jbl com WARNING Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing We recommend listening at low or moderate levels while driving your car JBL accepts no liability for hearing loss bodily injury or property damage resulting from the use or misuse of this product IMPORTANT To get the best performance from your JBL CS Series amplifiers we strongly recommend that installation be entrusted to a qualified professional Although these instructions explain how to install CS amplifiers in a general sense they do not show specific installation methods that may be required for your particular vehicle If you do not have the necessary tools or experience do not attempt the installation yourself Instead please ask your authorized JBL car audio dealer about professional installation INSTALLATION WARNINGS AND TIPS e Always wear protective eyewear when using tools e Turn off the audio system and other electrical d2. N e 160W RMS x 2 channels at 4 ohms 14 4V supply and lt 1 THD N e Dynamic power 145W at 2 ohms e Effective damping factor 6 395 at 4 ohms e Frequency response 10Hz 27kHz 3dB e Maximum input signal 6V e Maximum sensitivity 100mV e Output regulation 0 03dB at 4 ohms e Dimensions L x W x H 13 1 4 x 10 1 4 x 2 3 16 e Fuses 25A x 2 CS60 2 e 60W RMS x 2 channels at 4 ohms and lt 1 THD N e Signal to noise ratio 86dBA reference 1W into 4 ohms e 80W RMS x 2 channels at 2 ohms 14 4V supply and lt 1 THD N e 160W RMS x 1 channel at 4 ohms 14 4V supply and lt 1 THD N e Dynamic power 160W at 2 ohms e Effective damping factor 6 395 at 4 ohms e Frequency response 10Hz 27kHz 3dB e Maximum input signal 6V e Maximum sensitivity 100mV e Output regulation 0 03dB at 4 ohms e Dimensions L x W x H 8 7 8 x 10 1 4 x 2 1 4 e Fuses 25A x 1 This product is intended for mobile applications without connection to the 110 230 volts mains Features specifications and appearance are subject to change without notice Declaration of Conformity CE We Harman Consumer Group International 2 route de Tours 72500 Chateau du Loir France declare in own responsibility that the products described in this owner s manual are in compliance with technical standards EN 55013 2001 A1 2003 EN 55020 2002 A1 2003 ih L ai Klaus Lebherz Harman Consumer Group In
3. Adjust the crossover frequency to limit bass and provide increased system volume with less distortion For subwoofers choose the highest frequency that removes vocal information from the sound of the subwoofer If using the CS60 4 or CS60 2 to drive a subwoofer s set the crossover mode to LP low pass SETTING INPUT SENSITIVITY 1 Initially turn the INPUT LEVEL control s to minimum counter clockwise 2 Reconnect the negative lead to the vehicle s battery Apply power to the audio system and play a dynamic music track 3 On the source unit increase the volume control to 3 4 volume Slowly increase the INPUT LEVEL control s toward three o clock until you hear slight distortion in the music Then reduce the INPUT LEVEL slightly until distortion is no longer heard NOTE After the source unit is on blue LEDs on the top panel will light indicating the amplifier is on If not check the wiring especially the remote connection from the source unit Also refer to Troubleshooting guide at right TROUBLESHOOTING SYMPTOM LIKELY CAUSE SOLUTION No audio No voltage at BATT Check voltages at POWER LEDs or REM terminals amplifier terminals are off or bad or no ground with VOM connection No audio Amplifier is Make sure amplifier POWER overheated cooling is not blocked LEDs are on No audio POWER LEDs flash Voltage more than 16V or less than 8 5V on BATT connection Voltage less th
4. LPF BOOST system installation Figures 4 and 5 show how to configure the CS300 1 ep OR a aioe ae DE subwoofer amplifier NOTE For simplicity Figures 4 and 5 do not show power remote and input connections Subwoofer Subwoofer NOTE Minimum speaker load is 2 ohms total Figure 5 CS subwoofer amplifier with one woofer connected CS300 1 8 INPUT BASS LEVEL LPF BOOST 6v 100mv 32Hz 320Hz 0OdB 6dB Subwoofer APPLICATIONS CS60 4 The CS60 4 can be set up for stereo Front Left Front Right 4 channel 3 channel or bridged 2 channel operation as shown in Figures 6 through 8 NOTE For simplicity Figures 6 through 8 do not show power remote and input connections Figure 6 CS60 4 amplifier in 4 channel stereo operation to drive front and rear full range speakers FRONT REAR INPUT INPUT NOTE Minimum speaker impedance LEVEL aa i LEVEL 6V 100mV FREQ FREQ 6V 100mV for stereo operation is 2 ohms ais sone a ae Minimum speaker impedance for Boost Boost ods dB m 32HZ 320hz 32HZ 320Hz ods dB p 1 bridged operation is 4 ohms HP FLAT LP HP FLAT LP Rear Left Rear Right Front Left Front Right Figure 7 CS60 4 is set up for 3 channel operation to drive a set of full range speakers and a subwoofer FRONT REAR INPUT INPUT LEVEL X OVER X OVER LEVEL 6v 100mV FREQ FREQ 6V 100mV BASS MODE MODE
5. BASS BOOST BOOST ods SaB 32HZ 320Hz 32Hz 320Hz ods 6dB HP FLAT LP HP FLAT LP Figure 8 CS60 4 used in bridged 2 channel mode to drive a set of components or subwoofers Set crossovers according to application FRONT REAR INPUT INPUT ever X OVER X OVER EVEL 6v 100mV FREQ FREQ 6V 100mV BASS MODE MODE BASS BOOST BOOST ods BaB 32Hz 320Hz 32Hz 320Hz odB eag 1 in HP FLAT LP HP FLAT LP APPLICATIONS CS60 2 Figure 9 CS60 2 used in 2 channel stereo operation to drive a set of full range speakers INPUT BASS LEVEL FREQ BOOST 1 st ee ts 6v 100mV 32Hz 320Hz LP FLAT HP OdB 6dB Figure 10 CS60 2 used in bridge mode to drive a subwoofer BRIDGE INPUT BASS LEVEL FREQ BOOST MODE ev yoomv 32Hz 320Hz LP FLAT HP O0dB 6dB Subwoofer CONTROLS AND SETUP SETTING THE CROSSOVER S Determine your system plans and set the crossover mode switch accordingly If your system design does not include a subwoofer with the CS60 4 set the crossover mode to FLAT and skip to Setting Input Sensitivity Initially set the crossover frequency control midway While listening to music adjust the crossover for the least perceived distortion from the speakers allowing them to reproduce as much bass as possible Systems using a separate subwoofer set the crossover mode to HP high pass for your full range speakers
6. an 9V on BATT connection DC voltage on amplifier output at mounting location verify speaker system impedance is within specified limits Check vehicle charging system Check vehicle charging system Amplifier may need service see enclosed warranty card for service information Distorted audio Distorted audio Input sensitivity is not set properly or amplifier or source unit is defective Short circuit in Check INPUT LEVEL setting or check speaker wires for shorts or grounds Remove speaker leads and POWER speaker or wire one at a time to locate LEDs flash shorted speaker or wire then repair Music lacks Speakers are not Check speaker punch connected properly connections for proper polarity SPECIFICATIONS CS300 1 e 200W RMS x 1 channel at 4 ohms and lt 1 THD N e Signal to noise ratio 100dBA reference 1W into 4 ohms e 300W RMS x 1 channel at 2 ohms 14 4V supply and lt 1 THD N e Dynamic power 460W at 2 ohms e Effective damping factor 6 395 at 4 ohms e Frequency response 10Hz 300Hz 3dB e Maximum input signal 6V e Maximum sensitivity 100mV e Output regulation 0 07dB at 4 ohms e Dimensions L x W x H 12 11 16 x 10 1 4 x 2 3 16 e Fuses 20A x 2 CS60 4 e 60W RMS x 4 channels at 4 ohms and lt 1 THD N e Signal to noise ratio 86dBA reference 1W into 4 ohms e 80W RMS x 4 channels at 2 ohms 14 4V supply and lt 1 THD
7. d by the feet of backseat passengers Make sure that the amplifier is mounted securely using nuts and bolts or the supplied mounting screws Mount the amplifier so that it remains dry never mount an amplifier outside the vehicle or in the engine compartment INSTALLATION POWER CONNECTIONS The CS amplifiers require a reliable connection to the vehicle s electrical system in order to perform optimally See Figures 1 2 and 3 for terminal connection locations Please adhere to the following instructions carefully Ground Connection Connect the amplifier s Ground GND terminal to a solid point on the vehicle s metal chassis as close to the amplifier as possible Refer to the wire gauge chart to determine minimum wire gauge size Sand away any paint from this location use a star type lock washer to secure the connection Power Connection Connect a wire see chart at right for appropriate gauge directly to the vehicle s positive battery terminal and install an appropriate fuse holder within 18 of the battery terminal Do not install the fuse at this time Route the wire to the amplifier s location and connect it to the amplifier s Positive 12V terminal Be sure to use appropriate grommets whenever routing wires through the firewall or other sheet metal Failure to adequately protect the positive wire from potential damage may result in a vehicle fire When you are done routing and connecting this wire you may
8. evices before you start Disconnect the negative lead from your vehicle s battery e Atthe installation sites locate and make a note of all fuel lines hydraulic brake lines vacuum lines and electrical wiring Use extreme caution when cut ting or drilling in and around these areas e Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws Remember that the screws can extend behind the surface e Before drilling or cutting holes use a utility knife to remove unwanted fabric or vinyl to keep material from snagging in a drill bit e When routing cables keep input signal cables away from power cables and speaker wires e When making connections make certain they are secure and properly insulated e lf the amplifier s fuse must be replaced use only the same type and rating as that of the original Do not substitute another kind CHOOSING A LOCATION AND MOUNTING THE AMPLIFIER Choose a mounting location in the trunk or cargo area where the amplifier will not be damaged by shifting cargo Amplifier cooling is essential for proper amplifier operation If the amplifier is to be installed in an enclosed space make sure there is sufficient air circulation for the amplifier to cool itself When mounting the amplifier under a seat ensure that it is clear of all moving seat parts and does not affect the seat adjustments Mount the amplifier so it is not damage
9. install the fuse at the battery Figure 1 Terminal connection end plate for CS300 1 Remote Connection Connect the amplifier s Remote REM terminal to the source unit s Remote Turn On lead using a minimum of 18 gauge wire NOTE If your source unit does not have a remote turn on connection connect the amplifier s REM terminal to the vehicle s accessory circuit Speaker Connections Refer to the application guides on the pages that follow Speaker connections should be made using a minimum of 16 gauge wire inl Lo SPEAKER OUTPUTS __I FUSE BRIDGE Wire Gauge Chart Amplifier Maximum Minimum Model Current Draw Wire Gauge CS60 2 22A 8 AWG CS60 4 40A 8 AWG CS300 1 42A 8 AWG These recommendations assume 10 12 wire runs If your installation differs mark edly you will need to adjust the wire gauge accordingly APPLICATIONS CS300 1 The CS subwoofer amplifier is a single channel amplifier There are two sets of terminals to make it easy to connect multiple woofers Either set of terminals may be used when connecting woofers Figure 4 CS subwoofer amplifier with two woofers connected CS300 1 To the right are two application INPUT BASS diagrams to help plan your subwoofer LEVEL
10. ternational Chateau du Loir France 7 05 JBL Consumer Products 250 Crossways Park Drive Woodbury NY 11797 USA 2005 Harman International Industries Incorporated All rights reserved JBL is a trademark of Harman International Industries Incorporated registered in the United States and or other countries Part No CSAMPOM7 05 H A Harman International Company x
Download Pdf Manuals
Related Search