Intellinet Network Solutions 510486 Digital Camera User Manual
Contents
1. NOTE All Category 5 UTP Cate 568A type Cat6 568B type cable used for 100Base TX White Green White Orange connections should also work Green Orange for 1000Base T providing all White Orange White Green four wire pairs are connected ane x PIE It is recommended however Orange Green that Cat6 cable be used for all White Brown White Brown critical or new installations Brown Brown Positioning the Converter The location of the converter during operation can greatly affect its QINTELLINET E performance Consider these guidelines when deciding where to place the device Place the converter in a fairly cool and dry location See Specifications for the acceptable temperature and humidity operating ranges Place the converter in a location free from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight Place the converter in a location with easy access to AC power Place the converter on a clean flat surface that leaves at least 10 cm 4 in of space at the front and rear of the device for ventilation Affix the provided rubber pads to the bottom of the converter to protect the case from scratches and prevent slipping NOTE For mounting on a vertical surface use the underside of the unit as a template to measure and mark out the position of the holes on the installation surface then use two screws to mount the converter in place WARNING Exercise caution if2. External power adapter User manual Model 515320 Fast Ethernet Media Converter Standards IEEE 802 3 Twisted Pair Ethernet IEEE 802 3u Twisted Pair Fiber Optic Fast Ethernet General Media support 100Base TX Cat3 or higher UTP STP RJ 45 EIA TIA 568 100Base FX multi mode 62 5 125 or 50 125 um fiber Connectors RJ 45 port 100Base TX Fiber ST duplex port 100Base FX Distances 2km 1 24 mi 62 5 125 or 50 125 um fiber cable 100 m 300 ft RJ 45 cable Wavelength 1300 nm Min TX power 20 dBm Max TX power 14 dBm RX sensitivity 31 dBm Min power budget 11 dB Max power budget 17 dB Certifications FCC Class A CE Mark LEDs COL flashes to indicate data collision FDX indicates full duplex mode ACT flashes to indicate data traffic LNK indicates receiving link pulses from compliant device LFS indicates a break or disruption in copper or fiber links 100 indicates data packets are being transmitted at 100 Mbps DIP Switches DIP 1 Enables disables auto neg DIP 2 Copper port RJ 45 duplex mode full duplex or half duplex DIP 3 Copper port RJ 45 data bit rate 10 Mbps or 100 Mbps DIP 4 Fiber port duplex mode full duplex or half duplex DIP 5 Enables disables link fault signaling LFS DIP 6 Enables disables local loopback LLB DIP 7 Enables disables remote loopback RLB Power Ext power adapter 12 V D
3. RX1310 TX1550 NOTE Variations among the models can be noted in the Specifications section at the back of this manual Product images in this manual may be representational and may not exactly match the media converter in this package WDM Media Converter models 510509 and 510523 need to be installed as pairs on opposite sides of the same fiber cable QINTELLINET DI FCC Warning This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the user manual may cause interference which the user will be required to correct at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct Overview Since all the INTELLINET NETWORK SOLUTIONS Media Converter models represented in this manual do not share all the same features refer to the product or its corresponding Specifications list to determine which of the following sections or items within the sections apply to the enclosed product For example not all of the LEDs defined in the status reference chart may
4. Certifications FCC Class A CE Mark LEDs COL flashes to indicate data collision FDX indicates full duplex mode ACT flashes to indicate data traffic LNK indicates receiving link pulses from compliant device LFS indicates a break or disruption in copper or fiber links 100 indicates data packets are being transmitted at 100 Mbps DIP Switches DIP 1 Enables disables auto neg DIP 2 Copper port RJ 45 duplex mode full duplex or half duplex DIP 3 Copper port RJ 45 data bit rate 10 Mbps or 100 Mbps DIP 4 Fiber port duplex mode full duplex or half duplex DIP 5 Enables disables link fault signaling LFS DIP 6 Enables disables local loopback LLB DIP 7 Enables disables remote loopback RLB Power Ext power adapter 12 V DC 0 5 A Environmental Metal housing Dimensions 133 L x 86 W x 29 H mm 5 23 x 3 4 x 1 1 in Weight 158 g 0 34 Ibs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Fast Ethernet Media Converter External power adapter User manual QINTELLINET Model 515351 Gigabit Ethernet Media Converter Standards IEEE 802 3ab Twisted Pair Gigabit Ethernet IEEE 802 3z Fiber Optic Gigabit Ethernet General Media support 1000Base T Cat5e or higher UTP STP RJ 45 1000Base SX multi mod
5. Multi mode 500m 100m ene 100m UTP Fiber Cable UTP In the configuration below redundant link converters function as a high speed bridge between switches creating increased capacity for each user node on the local area network and providing a 10 100 1000 Mbps full duplex link to a variety of Fast or Gigabit Ethernet network devices within a LAN Gigabit Ethernet Switch Gigabit Ethernet Switch Multi mode 500m Single mode up ta 110km Primary link Enhanced 10410010007 to Enhanced 1070010007 to I000SAILX Converter Redundant link 100054 LX Converter Switch Converter Converter Server In the configuration below the converters function as a server aggregation for an enterprise or LAN configuration providing a 1000 Mbps full duplex link to a workgroup of 10 100 switches located on separate floors within a single building NETWO RK SOLUTIONS 13 Gigabit Switch Multi mode 500m Long Haul single Mode 80 000 m 100 m UTP Fiber Cable UTP In the configuration below redundant link converters function as a server aggregation for an enterprise or LAN configuration providing a 10 100 1000 Mbps full duplex link to a workgroup of 10 100 1000 switches located on separate floors within a single building Gigabit Ethernet Switch Multi mode S00m Single mode up ta 110km Primary link UTP 1000M Enhanced 101000007 to Enhanced 10100000T to 1000S4 LA Converter Redundant link 1000S4W LA
6. be featured on your media converter FUNCTIONS amp INDICATORS Auto MDI Auto MDI medium dependent interface detection alleviates concerns about cabling configuration by allowing direct connection to a workstation switch LAN card hub or oiner network devices when connecting between RJ 45 ports HO E ee Auto MDI marked next to the RJ 45 port on the front panel of Model 515386 RCV FD 1000 QINTELLINET DIP Switches The DIP dual in line package switches on the rear panel of some models enable a variety of functions that are printed in a convenient reference key alongside the switches NOTE A DIP switch reference list is also listed in the product s Specifications In the example at right model 515344 DIP switches 6 and 7 enable the Local Loopback LLB and Remote Loopback RLB diagnostic functions see Loopback Testing 7 Loopback Testing On some models see Specifications DIP switches let you activate both local and remote loopback diagnostic test functions Check for proper cable connections first and run the test with a traffic level of at least 50 percent of capacity to optimize the brightness of the LED indicators Don t conduct both loopback tests at the same time _ se no men _ n a m a a nn N 74 E le apar Fiber N n c Nec a a omputer A IRR pi MI Local Loopback M Remote Loopback Local Loopback Use a local loopback set the designated D
7. se the Auto MDI MDI X function on a converter s RJ 45 port alleviates concerns about cabling configuration when connecting to a 1000Base T device Whether connecting to a switch a LAN card or any other network device via the RJ 45 port simply plug it in and proceed See Connecting Copper Cable below 10 100Base TX Port A 10 100Base TX port supports network speeds of either 10 Mbps or 100 Mbps and can operate in half and full duplex transfer modes The RJ 45 connector is suitable for UTP cable Category 3 4 5 or better 10 100 1000Base T Port The 10 100 1000Base T port supports a network speed of 10 Mbps 100 Mbps or 1 000 Mbps and operates in full duplex transfer mode The RJ 45 connector is suitable for UTP cable Category 5 or better 10 100 1000Base TX Port A 10 100 1000Base TX port supports network speeds of 10 Mbps 100 Mbps or 1 000 Mbps and can operate in half and full duplex transfer modes The RJ 45 connector is suitable for UTP cable Category 3 4 5 or better 100Base FX Port A 100Base FX port adds a fiber Fast Ethernet link to your network device Compliant with IEEE 802 3u this port can transmit data at 100 Mbps in 0 QINTELLINET full duplex mode across distances of up to 2 km over multi mode fiber optic cable The fiber port has a choice of three fiber connector types ST SC or WDM 100Base TX Port The 100Base TX port supports network speed of 100 Mbps and can operate in half and full duplex transf
8. 0 Mbps On Data packets are being transmitted at 1000 Mbps Off Data packets are being transmitted at 10 100 Mbps On Data is being transmitted received On A failure has occurred on a fiber or copper link On Data collisions are occurring FD FDX On The device or corresponding link is operating in full duplex mode The device or corresponding link is operating in half duplex mode A break or disruption exists in copper or fiber links LNK A link has been established with a compliant device Flashing Data is being transmitted received LNK ACT combined No valid link is established to the port PRI The primary link is receiving link pulses from a compliant device The signal has been lost on the primary fiber port PWR Power is being received for normal operation No power is being received RCV Data packets are being received Flashing Data packets are being received at a slower rate Off No data packets are being received RDT On The redundant link is receiving link pulses from a compliant device Off The signal has been lost on the redundant fiber port Applicable with multi speed models QINTELLINET CONNECTIONS amp INSTALLATION Ports As mentioned in the Introduction the type of media converter ports will vary from model to model Refer to each model s Specifications at the back of this manual to identify a port and see below for explanations of their various uses and limits Auto MDI MDI X Though not a port per
9. 34 lbs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Gigabit Ethernet Redundant Link Media Converter External power adapter User manual Model 510493 Gigabit Ethernet Media Converter Standards IEEE 802 3ab Twisted Pair Gigabit Ethernet IEEE 802 3z Fiber Optic Gigabit Ethernet General Media support 1000Base T Cat5e or higher UTP STP RJ 45 Fiber media support depends on SFP module Connectors RJ 45 port 1000Base T SFP module slot Distances 100 m 300 ft RJ 45 cable Fiber distance depends on SFP module Safety amp EMI certificates FCC Class A CE Mark LEDs Power LINK ACT for RJ 45 port 1000 Mbps link for RJ 45 port LINK ACT for fiber SFP port ALM indicator for errors on copper or fiber connection DIP Switches Link Fault Signaling LFS on off Power External power adapter 12 V DC 0 5 A Power consumption 4 9 Watts maximum Environmental Metal housing Dimensions 102 L x 74 W x 22 H mm 4 x 2 9 x 0 9 in Weight 160 g 0 34 lbs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Gigabit Ethernet Media Converter External power adapter User manual QI
10. C 0 5 A Power consumption 2 4 Watts maximum Environmental Metal housing Dimensions 133 L x 86 W x 29 H mm 5 23 x 3 4 x 1 1 in Weight 158 g 0 34 Ibs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Fast Ethernet Media Converter External power adapter User manual QINTELLINET Model 515337 Fast Ethernet Media Converter Standards IEEE 802 3 Twisted Pair Ethernet IEEE 802 3u Twisted Pair Fiber Optic Fast Ethernet General Media support 100Base TX Cat3 or higher UTP STP RJ 45 EIA TIA 568 100Base FX multi mode 62 5 125 or 50 125 um fiber Connectors RJ 45 port 100Base TX Fiber SC duplex port 100Base FX Distances 2 km 1 24 mi 62 5 125 or 50 125 um fiber cable 100 m 300 ft RJ 45 cable Wavelength 1300 nm Min TX power 20 dBm Max TX power 14 dBm RX sensitivity 31 dBm Min power budget 11 dB Max power budget 17 dB Certifications FCC Class A CE Mark LEDs COL flashes to indicate data collision FDX indicates full duplex mode ACT flashes to indicate data traffic LNK indicates receiving link pulses from compliant device LFS indicates a break or disruption in copper or fiber links 100 indicates data packets are QINTELLINET being transmitted at 100 Mbps DIP Switche
11. Converter Switch Converter Converter Workstation In this configuration the converters function as a high speed dedicated link within a campus network configuration providing a 1000 Mbps full duplex link to a remote network node Gigabit Switch Workstation Multi mode 500m Long Haul Single Mode 80 000 m 100m Fiber Cable UTP UTP K GINTELLINET UTIONS SPECIFICATIONS Model 510486 Gigabit Ethernet Redundant Link Media Converter Standards IEEE 802 3ab Twisted Pair Gigabit Ethernet IEEE 802 3z Fiber Optic Gigabit Ethernet General Media support 1000Base T Cat5e or higher UTP STP RJ 45 Fiber media support depends on SFP module Connectors RJ 45 port 10 100 1000Base T 2 SFP module slots 2nd slot for redundant link Distances 100 m 300 ft RJ 45 cable Fiber distance depends on SFP module Safety amp EMI certificates FCC Class A CE Mark LEDs Power LINK TX for RJ 45 port 1000 Mbps link for RJ 45 port LINK TX for fiber SFP port ALM indicator for errors on copper or fiber connection PRI Primary Link indicator RDT Redundant Link indicator QINTELLINET DIP Switches Link Fault Signaling LFS on off Power External power adapter 12 V DC 0 5 A Power consumption 4 9 Watts maximum Environmental Metal housing e Dimensions 102 L x 74 W x 22 H mm 4 x 2 9 x 0 9 in Weight 160 g 0
12. IP switch to On to enable to check that the copper segment is connected properly Launch a loopback or diagnostics testing program see NOTE below and follow the program instructions Typically the instructions will be similar to the following 1 Enter the number of test messages frame packets to be sent 1 1000 CINTELLINET E 2 Click Start 3 The program will send a testing message looped in the copper segment and display a pass fail result Remote Loopback Use a remote loopback at the remote unit set the designated DIP switch to On at the local unit keep both loopback Dip switches Off disabled to check that the fiber segment is connected properly Launch a loopback or diagnostics testing program see NOTE below and follow the program instructions Typically the instructions will be similar to the following 1 Enter the number of test messages frame packets to be sent 1 1000 2 Click Start 3 The program will send a testing message looped in the fiber segment and display a pass fail result NOTE On a PC use a program such as Sniffer to conduct the tests Other methods include the SmartBits series of testing equipment If you do not have access to either method contact your vendor for advice IMPORTANT Deactivate both the local and the remote loopback test functions for normal converter operation Link Fault Signaling LFS Link Fault Signaling LFS is an important function that is extrem
13. MEDIA CONVERTER Shown Model 515368 NETWORK SOLUTIONS INT MEDCON UM 0908 01 INTRODUCTION Thank you for purchasing this INTELLINET NETWORK SOLUTIONS Media Converter The models listed below vary in the type and number of ports connectors data transfer rates and added features but all are designed so network managers can install fiber cabling anywhere within a network without changing the arrangement of copper based Ethernet The compact size of the converter allows for easy deployment in any narrow desktop location or wall mount installation and if needed several converters can be grouped in a 19 rack mountable chassis Easy to follow instructions in this user manual help make installation of this converter quick and simple so you ll also soon be enjoying the benefits of these features common to all models listed Auto MDI MDI X support Status LEDs for easy monitoring of device status External power adapter Lifetime Warranty This user manual is included with the following items 519069 Ethernet Media Converter 515320 Fast Ethernet Media Converter 515337 Fast Ethernet Media Converter 515344 Fast Ethernet Media Converter 510493 Gigabit Ethernet Media Converter 515351 Gigabit Ethernet Media Converter 515368 Gigabit Ethernet Media Converter 510486 Gigabit Ethernet Redundant Link Media Converter 510509 Gigabit Ethernet WDM Media Converter RX1550 TX1310 510523 Gigabit Ethernet WDM Media Converter
14. NTELLINET Models 510509 amp 510523 Gigabit Ethernet WDM Media Converters Standards IEEE 802 3ab Twisted Pair Gigabit Ethernet IEEE 802 3z Fiber Optic Gigabit Ethernet General Media support 1000Base T Cat5e or higher UTP STP RJ 45 1000Base LX single mode 9 125 um fiber Connectors RJ 45 port 1000Base T Fiber SC port 1000Base LX Distances 10 km 6 2 mi 9 125 um fiber cable 100 m 300 ft RJ 45 cable Wavelengths Model 510509 Receive RX 1550 nm Transmit TX 1310 nm Wavelengths Model 510523 Receive RX 1310 nm Transmit TX 1550 nm Min TX power 9 dBm Max TX power 3 dBm RX sensitivity 21 dBm Min power budget 12 dB Max power budget 18 dB Safety amp EMI certificates FCC Class A CE Mark LEDs Power Full half duplex QINTELLINET LINK TX for RJ 45 port LINK TX for fiber SC port DIP Switches DIP 1 Enables disables local loopback LLB DIP 2 Enables disables remote loopback RLB Power External power adapter 12 V DC 0 5 A Power consumption 3 4 Watts maximum Environmental Metal housing Dimensions 109 L x 74 W x 23 H mm 4 2 x 2 9 x 0 9 in Weight 160 g 0 34 Ibs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Gigabit Ethernet WDM Media Converter
15. e 50 125 um amp 62 5 125 um fiber Connectors RJ 45 port 1000Base T Fiber SC duplex port 1000Base SX Distances 220 m 720 ft 62 5 125 um fiber cable 550 m 1800 ft 50 125 um fiber cable 100 m RJ 45 cable Wavelength 850 nm Min TX power 9 5 dBm Max TX power 4 dBm RX sensitivity 18 dBm Link budget 8 5 dB Safety 8 EMI certificates FCC Class A CE Mark LEDs Power LINK TX for RJ 45 port LINK TX for fiber SC port DIP Switches e N Way on off QINTELLINET Power Ext power adapter 12 V DC 0 5 A Power consumption 3 4 Watts maximum Environmental Metal housing Dimensions 102 L x 74 W x 22 H mm 4 x 2 9 x 0 9 in Weight 158 g 0 34 lbs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Gigabit Ethernet Media Converter External power adapter User manual Model 515368 Gigabit Ethernet Media Converter Standards IEEE 802 3ab Twisted Pair Gigabit Ethernet IEEE 802 3z Fiber Optic Gigabit Ethernet General Media support 1000Base T Cat5e or higher UTP STP RJ 45 1000Base LX single mode 9 125 um fiber Connectors RJ 45 port 1000Base T Fiber SC duplex port 1000Base LX Distances 10 km 6 2 mi 9 125 um fiber cable 100 m 300 ft RJ 45 cable Wavelength 1310 nm M
16. ely beneficial in terms of network status monitoring The LFS function monitors both the copper and fiber segments to ensure that the Spanning Tree Protocol can kick in the moment a link failure occurs on either segment Set LFS to On for normal operations set to Off when installing cables or when testing the network connection NOTE The LFS feature influences both fiber and copper segments When disruption occurs on the copper segment the fiber segment will be disabled When the fiber segment loses signal the copper segment will be disabled Any link failure including during periods of precautionary switching to the redundant link and during Link Fault Signaling will cause the ALM LED to light up see LEDs To utilize the full benefits of LFS four converters can be used to build a primary and a secondary path between two switches The switches must a GC INTELLINET support Spanning Tree or Fast Spanning Tree protocols By default transmission of data will travel via the primary path If a link failure is detected transmission will automatically be switched to the secondary path by Spanning Tree Protocol delivering non stop network connectivity LEDs Front panel LEDs provide at a glance network status and real time connectivity information NOTE The PWR power LED is located on the rear panel on some models Status Indication On Data packets are being transmitted at 100 Mbps Off Data packets are being transmitted at 1
17. er modes The RJ 45 connector is suitable for UTP cable Category 3 4 5 or better 1000Base LX Port The 1000Base LX port adds a fiber Gigabit Ethernet link to your network device Compliant with IEEE 802 3z this port transmits data at 1 000 Mbps in full duplex mode across distances of up to 220 m over multi mode fiber optic cable The fiber port accepts SC or WDM connectors 1000Base T Port The 1000Base T port supports a network speed of 1 000 Mbps and operates in full duplex transfer mode The RJ 45 connector is suitable for UTP cable Category 5 or better Redundant Gigabit SFP Slot To connect a fiber cable s connector to a converter s SFP slot slide the selected SFP module mini GBIC into the SFP slot making sure that the module s receptors line up with the receptors at the back of the slot Push until you hear a click Once the module is inserted correctly take the cable connector and turn it so that it will fit into the mouth of the module Then push the connector into the mouth until its snaps into the receiving grooves in the module s mouth Use the appropriate type of multi mode or single mode fiber depending on the SFP module being used The fiber optics transmit data at up to 1 000 Mbps and can maintain data integrity over cable distances as long as 60 km depending on the selected SFP mini GBIC module QINTELLINET DI Cables Connecting Fiber Cable When connecting fiber cable to a 1000Base FX port on the conver
18. icates full duplex mode ACT flashes to indicate data traffic LNK indicates receiving link pulses from compliant device LFS indicates a break or disruption QINTELLINET in copper or fiber links 100 indicates data packets are being transmitted at 100 Mbps Switches e MDI MDI X selector for RJ 45 port Auto Negotiation on off Power Ext power adapter 12 V DC 0 5 A Environmental Metal housing Dimensions 133 L x 86 W x 29 H mm 5 23 x 3 4 x 1 1 in Weight 158 g 0 34 lbs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Fast Ethernet Media Converter External power adapter User manual INTELLINET BRINGING NETWORKS To LIFE INTELLINET NETWORK SOLUTIONS offers a complete line of active and passive networking products Ask your local computer dealer for more information or visit www intellinet network com Copyright INTELLINET NETWORK SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners
19. in TX power 9 5 dBm Max TX power 3 dBm RX sensitivity 20 dBm Link budget 10 5 dB Safety amp EMI certificates FCC Class A CE Mark LEDs Power Full half duplex LINK TX for RJ 45 port LINK TX for fiber SC port DIP Switches e N Way on off Power Ext power adapter 12 V DC 0 5 A Power consumption 3 4 Watts maximum Environmental Metal housing Dimensions 102 L x 74 W x 22 H mm 4 x 2 9 x 0 9 in Weight 158 g 0 34 Ibs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Gigabit Ethernet Media Converter External power adapter User manual QINTELLINET Model 519069 Ethernet Media Converter Standards IEEE 802 3 Twisted Pair Ethernet IEEE 802 3u Twisted Pair Fiber Optic Fast Ethernet General Media support 100Base TX Cat5e or higher UTP STP RJ 45 EIA TIA 568 100Base FX single mode 9 125 um fiber Connectors RJ 45 port 100Base TX Fiber SC duplex port 100Base FX Distances 30 km 18 6 mi 9 125 um fiber cable 100 m 300 ft RJ 45 cable Wavelength 1310 nm Min TX power 15 dBm Max TX power 8 dBm RX sensitivity 34 dBm Min power budget 19 dB Max power budget 26 dB Certifications FCC Class A CE Mark LEDs COL flashes to indicate data collision FDX ind
20. n affect network performance if not installed or positioned properly To help ensure your equipment operates at optimal levels Try to maintain a bend radius that s a minimum of 4x the diameter of to QINTELLINET the cable for UTP and 100x the diameter of the cable for fiber Avoid letting the cable twist too much to prevent excessive strain on internal cables Place cable ties at regular intervals being careful not to overtighten them Avoid using ties with fiber cable 6mm E Don t stretch cable especially around corners in vertical cable trays and when spanning long distances Cable Selection Use 100 Ohm Category 5 5e or 6 unshielded twisted pair UTP or shielded twisted pair STP cable for 1000Base T configurations referring to the pin assignments below as needed Pin MDI Signal Name MDI X Signal Name 1 Bi directional Data One Plus BI_D1 Bi directional Data Two Plus BI_D2 Bi directional Data One Minus BI_D1 Bi directional Data Two Minus BI_D2 Bi directional Data Two Plus BI_D2 Bi directional Data One Plus BI_D1 Bi directional Data Three Plus BI_D3 Bi directional Data Four Plus BI_D4 Bi directional Data Three Minus BI_D3 Bi directional Data Four Minus BI_D4 Bi directional Data Two Minus BI_D2 Bi directional Data One Minus BI_D1 Bi directional Data Four Plus BI_D4 Bi directional Data Three Plus BI_D3 Bi directional Data Four Minus BI_D4 Bi directional Data Three Minus BI_D3
21. s DIP 1 Enables disables auto neg DIP 2 Copper port RJ 45 duplex mode full duplex or half duplex DIP 3 Copper port RJ 45 data bit rate 10 Mbps or 100 Mbps DIP 4 Fiber port duplex mode full duplex or half duplex DIP 5 Enables disables link fault signaling LFS DIP 6 Enables disables local loopback LLB DIP 7 Enables disables remote loopback RLB Power Ext power adapter 12 V DC 0 5 A Power consumption 2 4 Watts maximum Environmental Metal housing Dimensions 133 L x 86 W x 29 H mm 5 23 x 3 4 x 1 1 in Weight 158 g 0 34 Ibs Operating temperature 0 50 C 32 122 F Operating humidity 10 80 RH non condensing Storage temperature 20 70 C 4 158 F Package Contents Fast Ethernet Media Converter External power adapter User manual Model 515344 Fast Ethernet Media Converter Standards IEEE 802 3 Twisted Pair Ethernet IEEE 802 3u Twisted Pair Fiber Optic Fast Ethernet General Media support 100Base TX Cat3 or higher UTP STP RJ 45 EIA TIA 568 100Base FX single mode 9 125 um fiber Connectors RJ 45 port 100Base TX Fiber SC duplex port 100Base FX Distances 30 km 18 6 mi 9 125 um fiber cable 100 m 300 ft RJ 45 cable Wavelength 1300 nm Min TX power 15 dBm Max TX power 8 dBm RX sensitivity 34 dBm Min power budget 19 dB Max power budget 26 dB
22. ter be sure an SC or WDM connector is used Other INTELLINET NETWORK SOLUTIONS Media Converter models may need cable that matches their ST ports Follow the steps below to properly connect fiber cable 1 Remove and keep the fiber port s rubber cover When not connected to a fiber cable the rubber cover should be replaced to protect the optics inside the device 2 Check that the fiber terminators are clean You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol Dirty fiber terminators on fiber optic cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port 3 Connect one end of the cable to the SC WDM port on the converter and the other end to the SC WDM port on the other device NOTE When inserting the cable be sure the tab on the plug clicks into position to ensure it s properly seated 4 Check the corresponding port LED on the converter to make sure the connection is valid Connecting Copper Cable The 1000Base T RJ 45 Ethernet port fully supports auto sensing and auto negotiation Follow the steps below to properly connect fiber cable 1 Insert one end of a Category 5 twisted pair cable into the RJ 45 port on the converter and the other end into the port of the network node 2 Check the corresponding port LED on the converter to make sure the connection is valid Cable Installation Tips Cables ca
23. using power tools to install the device Also because invisible laser radiation may be emitted from the aperture of the port when no cable is connected avoid exposure to laser radiation and do not stare into open apertures Powering On the Converter The converter uses an AC power supply 100 240 V AC 50 60 Hz The power supply automatically self adjusts to the local power source and may be powered on without having any or all LAN segment cables connected 1 Plug the power cable directly into the receptacle on the rear panel 2 Plug the power adapter into an available socket NOTE For international use you may need to change to an AC power adapter cord that has been approved for the receptacle type and electrical current in your country 3 Confirm that the PWR LED on the rear panel is lit indicating power to the device If it s not check that the power cable is correctly plugged in Sample Application Diagrams To effectively expand a Fast or Gigabit Ethernet network position a pair of converters back to back as illustrated in the examples that follow E GINTELLINET Switch Converter Converter Switch In the configuration below the converters function as a high speed bridge between switches creating increased capacity for each user node on the local area network and providing a 1000 Mbps full duplex link to a variety of Gigabit Ethernet network devices within a LAN Gigabit Switch Gigabit Switch
Download Pdf Manuals
Related Search