Home
Intel ET900 Mouse User Manual
Contents
1. Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the main board and you wish to use it If you install an add in FDC or the system has no floppy drive select Disabled in this field This option allows you to select the onboard FDD port L ET900 User s Manual 25 BIOS SETUP gt 0 Onboard Serial Port These fields allow you to select the onboard serial ports and their addresses The default values for these ports are Serial Port 1 3F8 IRQ4 Serial Port 2 2F8 IRO3 UART Mode Select This field determines the UART 2 mode in your computer The default value is Normal Other options include IrDA and ASKIR PWRON After PWR Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation E I SSS LL LL La 26 ET900 User s Manual BIOS SETUP Power Management Setup Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled ITEM HELP ACPI Suspend S1 POS RUN VGABIOS if S3 Resume Auto Menu Level gt Power Management User Define Video Off Method DPMS Video Off In Suspend Yes Suspend Type Stop Grant Modem Use IRQ 3 Suspend Mode Disabled HDD Power Down Disabled Soft Off by PWR BTTN nstant Off Wake Up by PCI Card Disabled Power On by Ring Disabled Resume by Alarm Disabled Date of Month Alarm 0 Time hh mm ss Alarm 0 0 0 Relo
2. VCC 5V SBY C87 GND D87 GND A88 PCIEO CK REF B88 RSVD C88 PEG RX11 D88 PEG TX11 A89 PCIEO CK REF B89 VGA RED C89 PEG RX11 D89 PEG TX11 A90 GND FIXED B90 GND FIXED C90 GND FIXED D90 GND FIXED A91 RSVD B91 VGA GRN C91 PEG RX12 D91 PEG TX12 A92 RSVD B92 VGA BLU C92 PEG RX12 D92 PEG TX12 A93 GPOO B93 VGA HSYNC C93 GND D93 GND A94 RSVD B94 VGA VSYNC C94 PEG_RX13 D94 PEG_TX13 A95 RSVD B95 VGA I2C CK C95 PEG RX13 D95 PEG TX13 A96 GND B96 VGA I2C DATA C96 GND D96 GND A97 VCC 12V B97 TV DAC A C97 RSVD D97 PEG_ENABLE VCC 12V TV DAC B PEG_RX14 PEG_TX14 VCC_12V TV_DAC_C PEG_RX14 PEG_TX14 GND FIXED GND FIXED GND FIXED GND FIXED VCC_12V VCC 12V PEG RX15 PEG TX15 VCC 12V VCC 12V PEG RX15 PEG TX15 VCC 12V VCC 12V GND GND VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V VCC 12V A110 GND FIXED B110 GND FIXED C110 GND FIXED ET900 User s Manual VCC_12V GND FIXED INTRODUCTION SSS This page is intentionally left blank gt 10 ET900 User s Manual BIOS SETUP BIOS Setup This chapter describes the different s
3. PNP PCI Configurations This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations nit Display First PCI Slot ITEM HELP Reset Configuration Data Disabled Menu Level Resources Controlled By Auto ESCD RQ Resources Press Enter Select Yes if you are using a Plug and Play capable operating system Select No if you need the BIOS to configure non boot devices PCI VGA Palette Snoop Disabled NT Pin 1 Assignment NT Pin 2 Assignment NT Pin 3 Assignment NT Pin 4 Assignment NT Pin 5 Assignment NT Pin 6 Assignment NT Pin 7 Assignment NT Pin 8 Assignment 000000 0 0 PCI Express relative items Maximum Payload Size Init Display First The default setting is PCI Card Reset Configuration Data This field allows you to determine whether to reset the configuration data or not The default value is Disabled Resources Controlled by This PnP BIOS can configure all of the boot and compatible devices with the use of a PnP operating system such as Windows 95 PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This field allows you to set whether or not MPEG ISA VESA VGA cards can work with PCI VGA When this field is enabled a PCI VGA can work with an MPEG ISA VESA VGA card When this field is disabled a PCI VGA cannot work with an MPEG
4. This setup program will install Intel R Graphics Media Accelerator Driver onto your computer It is strongly recommended that you exit all Windows programs before continuing setup Cancel ella Ins on Frameworks 4 When the setup is complete restart the computer as prompted and for changes to take effect Intel R Graphics Mi Accelerator Driver 4 The setup for the Intel R Graphics Media Accelerator Driver is complete You must restart your computer for changes to take effect Would you like to restart your computer now Yes want to restart my computer now C No will restart my computer later Remove any disks from their drives and then click Finish i ET900 User s Manual 39 DRIVERS INSTALLATION AC97 Codec Audio Driver Installation IP400 carrier board only Follow the steps below to install the Realtek AC97 Codec Audio Drivers 1 Insert the CD that comes with the board Click Intel Chipsets and then Intel R I945GM Chipset Drivers 2 Click Realtek Codec Audio Audio Driver 3 When the screen below appears click Yes to continue with the installation Digital Signature Not Found x The Microsoft digital signature affirms that software has been tested with Windows and that the software has not been altered since it was tested The software you are about to install does not contain a Microsoft digital signature Therefore there is no guarantee that this sof
5. Channel Master Slave The onboard PCI IDE connector provides Primary and Secondary channels for connecting up to two IDE hard disks or other IDE devices Press lt Enter gt to configure the hard disk The selections include Auto Manual and None Select Manual to define the drive information manually You will be asked to enter the following items CYLS Number of cylinders HEAD Number of read write heads PRECOMP Write precompensation LANDING ZONE Landing zone SECTOR Number of sectors The Access Mode selections are as follows CHS HD lt 528MB LBA HD gt 528MB and supports Logical Block Addressing Large for MS DOS only Auto Remarks The main board supports two serial ATA ports and are represented in this setting as IDE Channel 0 Drive A Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer The available specifications are 360KB 1 2MB 720KB 1 44MB 2 88MB 5 25in 5 25in 3 5in 3 5in 3 5in ET900 User s Manual 15 BIOS SETUP e eT Video This field selects the type of video display card installed in your system You can choose the following video display cards EGA VGA For EGA VGA SEGA SVGA or PGA monitor adapters default CGA 40 Power up in 40 column mode CGA 80 Power up in 80 column mode MONO For Hercules or MDA adapters Halt On This field determines whether or not the system will halt if an error is detected during powe
6. ISA VESA card Maximum Payload Size The default setting of the PCI Express Maximum Payload Size is 4096 JJ POOL LL a 30 ET900 User s Manual BIOS SETUP eee PC Health Status This section shows the parameters in determining the PC Health Status These parameters include temperatures fan speeds and voltages Phoenix AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature Disabled ITEM HELP Current System Temp 45 C 113 F Current CPU Temp 45 C 113 F Menu Level gt Vcore V 1 02 V Vcc3 3 3V Shutdown Temperature Disabled System FAN Speed 5400 RPM CPU FAN Speed 5400 RPM CPU Warning Temperature This field allows the user to set the temperature so that when the temperature is reached the system sounds a warning This function can help prevent damage to the system that is caused by overheating Temperatures Voltages These fields are the parameters of the hardware monitoring function feature of the main board The values are read only values as monitored by the system and show the PC health status Shutdown Temperature This field allows the user to set the temperature by which the system automatically shuts down once the threshold temperature is reached This function can help prevent damage to the system that is caused by overheating SSS Lg ET900 User s Manual 31 BIOS SETUP gt Frequency Voltage Control This sectio
7. carrier board ONLY sr aa a Geet tl 40 Intel PRO LAN Drivers Installation aaa 42 Marvell LAN Drivers Installation IP400 carrier board only PARE a a N a es ai na 43 IMPORTANT NOTE After installing your Windows operating system Windows 98SE ME 2000 XP you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation ET900 User s Manual 35 DRIVERS INSTALLATION Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug amp Play INF support for Intel chipset components Follow the instructions below to complete the installation under Windows 2000 XP 1 Insert the CD that comes with the board Click Intel Chipsets and then Intel R I945GM Chipset Drivers 2 Click Intel R Chipset Software Installation Utility eeu LL A ag 2 rjrj NHyMMTrtTyT77_ v e 36 ET900 User s Manual DRIVERS INSTALLATION 3 When the Welcome screen appears click Next to continue Intel R Chipset Software Installation Utility 7 2 1 1003 Welcome to the Intel R Chipset Software Installation Utility This program will install the Plug and Play components for the Intel R chipset that is on this system It is strongly recommended that you exit all Windows programs before continuing Cancel 4 Click Yes to accept the software license agreement and proceed with the installation
8. on the right select Magic Packet then click OK EAN OM UU 44 ET900 Users Manual
9. process 5 On Readme Information screen click Next to continue the installation Intel R Chipset Software Installation Utility 7 2 1 1003 Readme File Information Refer to the Readme file below to view system requirements and installation information Press the Page Down key to view the rest of the file Product Intel R Chipset Software Installation Utility Release Production Version 7 2 1 1003 Target Chipset E7230 Date June 23 2005 NOTE For the list of supported chipsets please refer to the Release Notes This document contains the following sections v lt Back Cancel 6 The Setup process is now complete Click Finish to restart the computer and for changes to take effect When the computer has restarted the system will be able to find some devices Restart your computer when prompted ET900 User s Manual 37 DRIVERS INSTALLATION VGA Drivers Installation To install the VGA drivers follow the steps below to proceed with the installation 1 Insert the CD that comes with the board Click Intel Chipsets and then Intel R I945GM Chipset Drivers 2 Click Intel R I945GM Chipset Family Graphics Driver LJ m T T 38 ET900 User s Manual DRIVERS INSTALLATION 3 When the Welcome screen appears click Next to continue Intel R Graphics Mi Accelerator Driver Accelerator Driver in Welcome to the setup for the Intel R Graphics Media tel e
10. 2 A60 GND FIXED B60 GND FIXED C60 GND FIXED D60 GND FIXED A61 PCIE_TX2 B61 PCIE_RX2 C61 PEG RX3 D61 PEG_TX3 A62 PCIE_TX2 B62 PCIE_RX2 C62 PEG_RX3 D62 PEG TX3 A63 GP B63 GPO3 C63 RSVD D63 RSVD A64 PCIE TX1 B64 PCIE RX1 C64 RSVD D64 RSVD A65 PCIE TX1 B65 PCIE RX1 C65 PEG RX4 D65 PEG TX4 A66 GND B66 WAKEO C66 PEG RX4 D66 PEG TX4 A67 GPI2 B67 WAKE1 C67 RSVD D67 GND A68 PCIE_TX0 B68 PCIE_RX0 C68 PEG_RX5 D68 PEG_TX5 A69 PCIE TXO B69 PCIE RXO C69 PEG RX5 D69 PEG TX5 A70 GND FIXED B70 GND FIXED C70 GND FIXED D70 GND FIXED A71 LVDS_A0 B71 LVDS B0 C71 PEG_RX6 D71 PEG TX9 A72 LVDS AO B72 LVDS B0 C72 PEG RX6 D72 PEG TX9 A73 LVDS_A1 B73 LVDS Bi C73 SDVO DATA D73 SDVO CLK A74 LVDS At B74 LVDS B1 C74 PEG_RX7 D74 PEG_TX7 A75 LVDS_A2 B75 LVDS_B2 C75 PEG_RX7 D75 PEG_TX7 A76 LVDS_A2 B76 LVDS B2 C76 GND D76 GND A77 LVDS VDD EN B77 NC C77 RSVD D77 IDE_CBLID A78 NC B78 NC C78 PEG_RX8 D78 PEG_TX8 A79 NC B79 LVDS BKLT EN C79 PEG_RX8 D79 PEG_TX8 A80 GND FIXED B80 GND FIXED C80 GND FIXED D80 GND FIXED A81 LVDS A CK B81 LVDS B CK f C81 PEG RX9 D81 PEG TX9 A82 LVDS A CK B82 LVDS B CK C82 PEG RX9 D82 PEG TX9 A83 LVDS I2C CK B83 LVDS BKLT Ctrl C83 RSVD D83 RSVD A84 LVDS I2C DAT B84 VCC 5V SBY C84 GND D84 GND A85 GPI3 B85 VCC 5V SBY C85 PEG RX10 D85 PEG TX10 A86 KBD_RSD B86 VCC_5V_SBY C86 PEG RX10 D86 PEG TX10 A87 KBD A20GATE B87
11. 2ET PHY ICH7M built in USB 2 0 host controller support 8 ports ICH7M built in SATA controller supports 2 ports Parallel IDE ICH7M built in one channel Ultra DMA 33 66 100 ICH7M Built in Audio controller AC97 Codec at carrier board Two 220 pin connectors A B amp C D Carrier Board Yes 256 segments 0 1 2 255 sec min 5V 3 3V 12V SVSB Modem Wakeup LAN Wakeup 95mm x 125mm ET900 User s Manual 3 INTRODUCTION Dimensions pan IO M M l lM 4 ET900 Users Manual INTRODUCTION LL Installing the Processor The ET900 is available with a processor socket on board or with an Intel processor on board In the case that your ET900 comes a Socket 479 processor socket for Intel Pentium M or Celeron M processors follow the instructions below regarding the processor installation The processor socket comes with a screw to secure the processor As shown in the left picture below loosen the screw first before inserting the processor Place the processor into the socket by making sure the notch on the corner of the processor corresponds with the notch on the inside of the socket Once the processor has slide into the socket fasten the screw Refer to the figures below NOTE Ensure that the CPU heat sink and the CPU top surface are in total contact to avoid CPU overheating problem that would cause your system to hang or be unstable E ET900 User s Manual 5 INTRODUCTION Instal
12. ET900 Intel Core Duo Solo 945GM COM Express Type II CPU Module USER S MANUAL Version 1 0 Acknowledgments Award is a registered trademark of Award Software International Inc PS 2 is a trademark of International Business Machines Corporation Intel and Celeron are registered trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corporation Winbond is a registered trademark of Winbond Electronics Corporation All other product names or trademarks are properties of their respective owners Attention Before installing the CPU heat sink remove the two protective sheaths as shown in the figure below Note Remove the protective sheath before installation LJ I LL LL ss ii ET900 Users Manual Table of Contents Introduction PER 1 Product Description 00 0e0000e 0000 1 Check hE see a lan 2 ET900 Specifications cee cesceseceseceseceseeeseeeeeeeeaeeeseeenaes 3 Dimensions i s scssccveseacaeceebsn sete ii aaa a aisiais ia ii 4 Installing the Processor lt aaa aaa a aaa aaa 5 Installing the Memory eeen 6 Connectors on ETIO senna a a 7 J2 J3 COM Express Type 2 Connectors eee 7 BIOS SGlup Lk ia ia iai i cate 11 Drivers Installation ccccsssssesseee 35 Intel Chipset Software Installation Utiility 36 VGA Drivers Installation 0 0 0 aaa aaa aaa aaa 38 AC97 Codec Audio Driver Installation IP400 carrier b
13. FIXED GND FIXED GND FIXED AC_BITCLK SPKR PCI AD13 PCI PAR AC SDOUT 12C_CK PCI_C BE1 PCI_SERR NC I2C DAT PCI PERR PCI STOP THRMTRIP THRM PCI LOCK PCI TRDY USB6 USB7 PCI DEVSELA PCI_FRAME USB6 USB7 PCI_IRDY PCI_AD16 USB_6_7_OC USB 4 5 OC PCI C BE2 PCI AD18 USB4 USB5 PCI AD17 PCI AD20 USB4 USB5 PCI AD19 PCI AD22 GND FIXED GND FIXED GND FIXED GND FIXED USB2 USB3 PCI AD21 PCI AD24 USB2 USB3 PCI AD23 PCI AD26 USB 2 3 OC USB 0 1 0C PCI_C BES PCI_AD28 USBO USB1 PCI AD25 PCI AD30 USB0 USB1 PCI AD27 PCI_IRQC VCC RTC EXCD1 PERTST PCI AD29 PCI_IRQD EXCD0_PERST EXCD1_CPPE PCI_AD31 NC EXCDOCPPE SYS_RESET PCI_IRQA NC LPC_SERIRQ CB_RESET PCI IRGB3 PCI CLK SSS E 8 ET900 User s Manual INTRODUCTION Pin Signal Pin Signal Pin Signal Pin Signal A51 GND FIXED B51 GND FIXED C51 GND FIXED D51 GND FIXED A52 NC B52 NC C52 PEG RX0 D52 PEG_TX0 A53 NC B53 NC C53 PEG RXO D53 PEG TXO A54 GPIO B54 GPO1 C54 NC D54 PEG LANE RV A55 NC B55 NC C55 PEG RX1 D55 PEG TX1 A56 NC B56 NC C56 PEG RX1 D56 PEG TX1 A57 GND B57 GPO2 C57 NC D57 NC A58 PCIE TX3 B58 PCIE RX3 C58 PEG RX2 D58 PEG TX2 A59 PCIE TX3 B59 PCIE RX3 C59 PEG RX2 D59 PEG TX
14. Feature Press Enter to configure the settings relevant to CPU Feature Hard Disk Boot Priority With the field there is the option to choose aside from the hard disks connected Bootable add in Cards which refers to other external devices Virus Warning If this option is enabled an alarm message will be displayed when trying to write on the boot sector or on the partition table on the disk which is typical of the virus CPU L1 and L2 Cache Cache memory is additional memory that is faster than conventional DRAM system memory CPUs from 486 type on up contain internal cache memory and most but not all modern PCs have additional external cache memory When the CPU requests data the system transfers the requested data from the main DRAM into cache memory for even faster access by the CPU These allow you to enable speed up memory access or disable the cache function L SS SS ET900 User s Manual 17 BIOS SETUP BE 7 T7 as Guick Power On Self Test When enabled this field speeds up the Power On Self Test POST after the system is turned on If it is set to Enabled BIOS will skip some items First Second Third Boot Device These fields determine the drive that the system searches first for an operating system The options available include Floppy LS120 Hard Disk CDROM ZIP100 USB Floppy USB ZIP USB CDROM LAN and Disable Boot Other Device These fields allow the system t
15. LAN drivers 1 Insert the CD that comes with the board Click LAN Card and then Marvell LAN Controller Driver a seisia Thi r 2 When the Welcome screeen appears click Next to continue IZ Marvell Miniport Driver InstallShield Wizard Welcome to the InstallShield Wizard for Marvell Miniport Driver The InstallShield R Wizard will install Marvell Miniport Driver on your computer To continue click Next WARNING This program is protected by copyright law and international treaties 3 Click Next to agree with the license agreement ET900 User s Manual 43 DRIVERS INSTALLATION gt gt gt 5 4 When the Readme Information appears click Next to continue 5 When the Ready to Install the Program appears click Install to continue 6 After the installation is complete click Finish fe Marvell Miniport Driver InstallShield Wizard x InstallShield Wizard Completed The InstallShield Wizard has successfully installed Marvell Miniport Driver Click Finish to exit the wizard 7 To use the wake up function with PCIe LAN go to the Device Manager under Windows and select LAN controller The window for Generic Marvell Yukon Chipset based Ethernet Controller Properties will appear Click Advanced and select Wake From Shutdown In the Value field on the right select On 8 Then also in the Advanced section click on Wake Up Capabilities In the Value field
16. ad Global Timer Events Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD COM LPT Port Disabled PCI PIRQ A D Disabled ACPI Function Enable this function to support ACPI Advance Configuration and Power Interface ACPI Suspend The default setting of the ACPI Suspend mode is 1 POS RUN VGABIOS if S3 Resume The default setting of this field is Auto Power Management This field allows you to select the type of power saving management modes There are four selections for Power Management Min Power Saving Max Power Saving User Define Minimum power management Maximum power management Each of the ranges is from 1 min to lhr Except for HDD Power Down which ranges from 1 min to 15 min ET900 User s Manual 27 BIOS SETUP e Video Off Method This field defines the Video Off features There are three options V H SYNC Blank Default setting blank the screen and turn off vertical and horizontal scanning DPMS Allows BIOS to control the video display Blank Screen Writes blanks to the video buffer Video Off In Suspend When enabled the video is off in suspend mode The default setting is Yes Suspend Type The default setting for the Suspend Type field is Stop Grant Modem Use IRQ This field sets the IRQ used by the Modem By default the setting is 3 Suspend Mode When enabled and after the set time of system inactivity all dev
17. cial support for detailed fine tuning of the chipset controlling the entire system BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the Award BIOS is immediately activated Pressing the lt Del gt key immediately allows you to enter the Setup utility If you are a little bit late pressing the lt Del gt key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the lt Ctrl gt lt Alt gt and lt Delete gt keys You can also restart by turning the system Off and back On again The following message will appear on the screen Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items lt Enter gt to select the lt PgUp gt and lt PgDn gt keys to change entries lt F1 gt for help and lt Esc gt to quit When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices SS EEE 12 ET900 User s Manual BIOS SETUP Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Freguency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimize
18. ctor Automatic TV Format Auto I og ET900 User s Manual 21 BIOS SETUP Panel Scaling The default setting is Auto The options available include On and Off Panel Number These fields allow you to select the LCD Panel type The default values for these ports are 640x480 18bit SC 800x480 18bit SC 800x600 18bit SC 1024x768 18bit SC 1280x1024 18bit DC 1280x768 18bit SC 1400x1050 18bit DC 1600x1200 18bit DC 22 ET900 Users Manual BIOS SETUP eee Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals The first screen shows three main items for user to select Once an item selected a submenu appears Details follow Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE Device Press Enter ITEM HELP Onboard Device Press Enter Menu Level gt SuperlO Device Press Enter Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device DE HDD Block Mode Enabled ITEM HELP On chip Primary PCI IDE Enabled DE Primary Master PIO Auto Menu Level gt DE Primary Slave PIO Auto DE Primary Master UDMA Auto DE Primary Slave UDMA Auto On Chip Secondary PCI IDE Enabled DE Secondary Master PIO Auto DE Secondary Slave PIO Auto DE Secondary Master UDMA Auto DE Secondary Slave UDMA Auto On Chip Serial ATA Setting On Chip Serial ATA Auto PATA IDE Mode Secondary SATA port PO P2 is Primary Phoenix AwardBIOS CMOS Setup Uti
19. d Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exit Without Saving ESC Quit MN gt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type The section below the setup items of the Main Menu displays the control keys for this menu At the bottom of the Main Menu just below the control keys section there is another section which displays information on the currently highlighted item in the list Note If the system cannot boot after making and saving system changes with Setup the Award BIOS supports an override to the CMOS settings that resets your system to its default Warning It is strongly recommended that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability Changing the defaults could cause the system to become unstable and crash in some cases ET900 User s Manual 13 BIOS SETUP AAA Standard CMOS Setup Standard CMOS Setup choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the board is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your syste
20. ettings available in the Award BIOS that comes with the board The topics covered in this chapter are as follows BIOS Introduction isis isso i ss a ps 12 BIOS Setpa ich ass siais Assists Ia asi si 12 Standard CMOS Setup Lake aaa aaa aaa aaa 14 Advanced BIOS Features aaa aaa aaa aaa aaa 17 Advanced Chipset Features aaa aaa aaa aka 20 Integrated Peripherals cscsesscsseecsseeecsseceeeecseeseeseseeeeeaeeees 23 Power Management Setup e cece cesecssecseceseceseceecseeeseeeeeeeeees 27 PNP PCI Configurations cccesececssecseesecneeeeceeeeecsseeeesseeeeeseenees 30 PC Health Stans ss 31 Frequency Voltage Control eee eeceecesecesecsseceeceeeseeeeeeeeees 32 Load Fail Safe Defaults ominie nikinin 33 Load Optimized Defaults eee eeceseeceteceeeeceeteecneseeesaeeeeeees 33 Set Supervisor User Password cescessssecsecsseeseeceeeeeeneeeeeees 33 save amp Exit SEt P sias hana koi e E EER E 33 Exit Without Saving s c cdcsceeseniastsstessesesensisiesesteosastbeebessussvepnens 33 ET900 User s Manual 11 BIOS SETUP EEE I BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel processors The BIOS provides critical low level support for a standard device such as disk drives serial ports and parallel ports It also adds virus and password protection as well as spe
21. hed Reducing the delay improves the performance of the SDRAM SSS SS LL LL 20 ET900 Users Manual BIOS SETUP ee DRAM RAS Precharge This option sets the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes The default setting for the Active to Precharge Delay is 4 Precharge Delay tRAS The default setting for the Precharge Delay is 12 System Memory Frequency The default setting is 533MHz SLP_S4 Assertion Width The default setting is J to 2 Sec System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Video BIOS Cacheable The Setting Enabled allows caching of the video BIOS ROM at C0000h F7FFFh resulting in better video performance However if any program writes to this memory area a system error may result Memory Hole At 15M 16M In order to improve performance certain space in memory can be reserved for ISA cards This memory must be mapped into the memory space below 16 MB The choices are Enabled and Disabled On Chip VGA Setting The fields under the On Chip VGA Setting and their default settings are PEG On Chip VGA Control Auto On Chip Frame Buffer Size SMB DVMT Mode DVTM DVMT Fixed Memory Size 128MB Boot Display Auto Panel Scaling Auto Panel Number 1024x768 18 bit SC TV Standard Off Video Conne
22. hen Auto is selected the BIOS will select the best available mode IDE Primary Secondary Master Slave UDMA These fields allow your system to improve disk I O throughput to 33Mb sec with the Ultra DMA 33 feature The options are Auto and Disabled SS LL LL a 24 ET900 User s Manual BIOS SETUP eee On Chip Serial ATA Setting The fields under the SATA setting includes On Chip Serial ATA Auto PATA IDE Mode Secondary and SATA Port PO P2 is Primary USB Controller The options for this field are Enabled and Disabled By default this field is set to Enabled USB 2 0 Controller The options for this field are Enabled and Disabled By default this field is set to Enabled In order to use USB 2 0 necessary OS drivers must be installed first Please update your system to Windows 2000 SP4 or Windows XP SP2 USB Keyboard Support The options for this field are Enabled and Disabled By default this field is set to Disabled AC97 Audio Select This field by default is set to Auto Power ON Function This field is related to how the system is powered on such as with the use of conventional power button keyboard or hot keys The default is BUTTON ONLY KB Power ON Password This field allows users to set the password when keyboard power on is the mode of the Power ON function Hot Key Power ON This field sets certain keys also known as hot keys on the keyboard that can be used as a switch to power on the system
23. ices except the CPU will be shut off HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Soft Off by PWRBTN This field defines the power off mode when using an ATX power supply The Instant Off mode allows powering off immediately upon pressing the power button In the Delay 4 Sec mode the system powers off when the power button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds Wake up by PCI Card By default this field is disabled Power On by Ring This field enables or disables the power on of the system through the modem connected to the serial port or LAN ee aM I E 28 ET900 Users Manual BIOS SETUP eee Resume by Alarm This field enables or disables the resumption of the system operation When enabled the user is allowed to set the Date and Time Reload Global Timer Events The HDD FDD COM LPT Ports and PCI PIRQ are I O events that can prevent the system from entering a power saving mode or can awaken the system from such a mode When an I O device wants to gain the attention of the operating system it signals this by causing an IRQ to occur When the operating system is ready to respond to the request it interrupts itself and performs the service L ET900 User s Manual 29 BIOS SETUP E T T7 7 EEE
24. ling the Memory The ET900 COM Express CPU module accommodates 200 pin DDR2 533 and DDR2 667 SODIMM memory modules with capacities up to 1GB Non ECC is supported Installing and Removing Memory Modules To install the DDR2 modules locate the memory slot on the board and perform the following steps m W Hold the DDR2 module so that the key of the DDR2 module align with those on the memory slot Insert the module into the socket at a slight angle approximately 30 degrees Note that the socket and module are both keyed which means that the module can be installed only in one direction To seat the memory module into the socket apply firm and even pressure to each end of the module until you feel it slip down into the socket With the module properly seated in the socket rotate the module downward Continue pressing downward until the clips at each end lock into position 4 To remove the DDR2 module press the clips with both hands ET900 User s Manual INTRODUCTION Connectors on ET900 J2 J3 COM Express Type 2 Connectors The Type 2 connectors come in two 220 pin 0 5mm pitch receptacles They include PCI IDE GBE and up to 22 general purpose PCIE lanes PCIE 0 5 and PCIE 16 31 For most Type 2 implementations it is expected that PCIE lanes 16 31 are used for graphics Hence they are designated PEG lanes 0 15 in the following table Modules implementing Pin out Type 2 such as the ET900 uses the pin
25. lity Onboard Device USB Controller Enabled ITEM HELP USB 2 0 Controller Enabled Menu Level gt USB Keyboard Support Disabled AC97 Audio Select Auto L ET900 User s Manual 23 BIOS SETUP eee Phoenix AwardBIOS CMOS Setup Utility SuperlO Device POWER ON Function BUTTON ONLY KB Power ON Password Enter Hot Key power ON Ctrl F1 Onboard FDC Controller Enabled Onboard Serial Port 1 3F8 IRQ4 Menu Level gt Onboard Serial Port 2 2F8 IRQ3 UART Mode Select Normal RxD TxD Active Hi Lo R Transmission Delay Disabled UR2 Duplex Mode Half Use IR Pins IR Rx2Tx2 PWRON After PWR Fail Off IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive On chip Primary PCI IDE Enabled This field by default is enabled OnChip Primary Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately IDE Primary Secondary Master Slave PIO These fields allow your system hard disk controller to work faster Rather than have the BIOS issue a series of commands that transfer to or from the disk drive PIO Programmed Input Output allows the BIOS to communicate with the controller and CPU directly The system supports five modes numbered from 0 default to 4 which primarily differ in timing W
26. m hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged Date mm dd yy Time hh mm ss IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave Drive A Drive B Video Halt On Base Memory Extended Memory Total Memory Phoenix AwardBIOS CMOS Setup Utili Standard CMOS Features Wed Apr 28 2004 00 00 00 None None None None 1 44M 3 5 in None EGA VGA All Errors 640K 129024K 130048K lt Item Help Menu Level gt Change the day month Year and century At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the lt F1 gt key It will display the relevant information to help you The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following describes each item of this menu Date The date format is Day Sun to Sat Month 1to12 Date 1t031 Year 1999 to 2099 LJ OO LL 14 ET900 Users Manual BIOS SETUP eee To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time Time The time format is Hour 00 to 23 Minute 00 to 59 Second 00 to 59 To set the time highlight the Time field and use the lt PgUp gt lt PgDn gt or keys to set the current time IDE
27. n shows the user how to configure the processor frequency Phoenix AwardBIOS CMOS Setup Utility Freguency Voltage Control Auto Detect PCI Clk Disabled ITEM HELP Spread Spectrum Modulated Disabled Menu Level gt Auto Detect PCI CIk This field enables or disables the auto detection of the PCI clock Spread Spectrum Modulated This field sets the value of the spread spectrum The default setting is Disabled This field is for CE testing use only SSS SS LL a 32 ET900 Users Manual BIOS SETUP eee Load Fail Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features Load Optimized Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features Set Supervisor Password These two options set the system password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a password highlight the type you want and press lt Enter gt The Enter Password message prompts on the screen Type the password up to eight characters in length and press lt Enter gt The system confirms your password by asking you to type it again After setting a password the screen automa
28. nabled SS SSS SS L LOL LL gs 3 ET900 User s Manual 19 BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable ITEM HELP CAS Latency Time Menu Level gt DRAM RAS to CAS Delay DRAM RAS Precharge Precharge delay tRAS 12 System Memory Frequency 533MHZ SLP_S4 Assertion Width 1 to 2 Sec System BIOS Cacheable Enabled Video BIOS Cacheable Disabled Memory Hole at 15M 16M Disabled PCI Express Root Port Func Press Enter On Chip VGA Setting PEG On Chip VGA Control Auto On Chip Frame Buffer Size 8MB DVMT Mode DVMT DVMT FIXED memory Size 128MB Boot Display Auto Panel Scaling Auto Panel Number 1024x768 18 bit SC TV Standard Off Video Connector Automatic TV Format Auto DRAM Timing Selectable This option refers to the method by which the DRAM timing is selected The default is By SPD CAS Latency Time You can configure CAS latency time in HCLKs as 2 or 2 5 or 3 The system board designer should set the values in this field depending on the DRAM installed Do not change the values in this field unless you change specifications of the installed DRAM or the installed CPU DRAM RAS to CAS Delay This option allows you to insert a delay between the RAS Row Address Strobe and CAS Column Address Strobe signals This delay occurs when the SDRAM is written to read from or refres
29. o search for an OS from other devices other than the ones selected in the First Second Third Boot Device Swap Floppy Drive This item allows you to determine whether or not to enable Swap Floppy Drive When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled Boot Up Floppy Seek This feature controls whether the BIOS checks for a floppy drive while booting up If it cannot detect one either due to improper configuration or its absence it will flash an error message Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system Gate A20 Option This field allows you to select how Gate A20 is worked Gate A20 is a device used to address memory above MB Typematic Rate Setting When disabled continually holding down a key on your keyboard will generate only one instance When enabled you can set the two typematic controls listed next By default this field is set to Disabled Typematic Rate Chars Sec When the typematic rate is enabled the system registers repeated keystrokes speeds Settings are from 6 to 30 characters per second LL LL 18 ET900 Users Manual BIOS SETUP eee Typematic Delay Msec When the typematic rate is enabled this item allows you to set the time interval for displaying the first and second characters By default this item is set to 250msec Security O
30. oard IN RS 40 Intel PRO LAN Drivers Installation aaa 42 Marvell LAN Drivers Installation IP400 carrier board only EE Dan aaa aaa aa aaa a aa ae a aa a A o asa 43 L J L gg ET900 Users Manual iii ti irit The ET900 945GM COM Express CPU Module a a ME iv ET900 Users Manual INTRODUCTION Introduction Product Description The ET900 board incorporates the Mobile Intel 945GM Express Chipset for Embedded Computing consisting of the Intel 945GM Graphic Memory Controller Hub GMCH and Intel I O Controller Hub 7 M ICH7 M an optimized integrated graphics solution with a 533MHz and 667MHz front side bus Dimensions of the board are 95mm x 125mm The integrated powerful 3D graphics engine based on Intel Graphics Media Accelerator 950 Intel GMA 950 architecture operates at core speeds of up to 400 MHz It features a low power design and is validated with the Intel Core Duo Solo on 65nm process With DDR2 667MHz SO DIMM socket on board the board supports up to 2GB of DDR2 system memory Intel Graphics Media Accelerator 950 supports a unique intelligent memory management scheme called Dynamic Video Memory Technology DVMT DVMT handles diverse applications by providing the maximum 224MB availability of system memory for general computer usage while supplying additional graphics memory when a 3D intensive application requests it The Intel GMA 950 graphics architecture al
31. out shown iF ET900 User s Manual 7 INTRODUCTION i Signal Signal Signal Signal GND FIXED GND FIXED GND FIXED GND FIXED NC GBEO_ACT DE_D7 IDE_D5 NC LPC_FRAME DE D6 DE D10 GBEO_LINK100 LPC_ADO DE_D3 DE D11 A5 NC B5 LPC AD1 C5 IDE D15 D5 DE D12 A6 NC B6 LPC AD2 C6 DE D8 D6 IDE D4 A7 NC B7 LPC AD3 C7 DE D9 D7 IDE DO A8 GBEO_LINK B8 LPC_DRQO C8 DE D2 D8 IDE REG A9 GBEO_MDI1 B9 LPC_DRQ1 cg IDE_D13 D9 IDE_IOW A10 GBEO MDI1 B10 LPC_CLK C10 DE Di D10 IDE ACK A11 GND FIXED B11 GND FIXED C11 GND FIXED D11 GND FIXED A12 GBE0_MDI0 B12 PWRBTN C12 IDE D14 D12 DE IRG A13 GBEO MDI0 B13 SMB CK C13 IDE IORDY D13 IDE AO A14 NC B14 SMB DAT C14 IDE IOR D14 IDE At A15 SUS_S3 B15 SMB_ALERT C15 PCI PME D15 IDE A2 A16 SATAO TX B16 SATA1 TX C16 PCI GNT24 D16 IDE CS1 A17 SATAO TX B17 SATA1 TX C17 PCI REG2 D17 IDE CS3 A18 SUS_S4 Bis SUS STAT C18 PCLGNT1 Di8 IDE_RESET A19 SATAO RX B19 SATA1_RX C19 Pci REG14 D19 PCI GNT3 A20 SATAO RX B20 SATA1 RX C20 PCI GNTO D20 PCI REQ3 GND FIXED GND FIXED GND FIXED GND FIXED NC NC PCI_REQO PCI_AD1 NC NC PCI RESET PCI AD3 SUS S5 NC PCI ADO PCI AD5 NC NC PCI AD2 PCI AD7 NC NC PCI AD4 PCI C BEO BATLOW NC PCI AD6 PCI AD9 ATA ACT AC SDIN2 PCI AD8 PCI AD11 AC SYNG AC SDIN1 PCI AD10 PCI AD13 SC RST AC SDINO PCI AD12 PCI AD15 GND FIXED GND
32. ption This field allows you to limit access to the System and Setup The default value is Setup When you select System the system prompts for the User Password every time you boot up When you select Setup the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up APIC Mode APIC stands for Advanced Programmable Interrupt Controller The default setting is Enabled MPS Version Control for OS This option is specifies the MPS Multiprocessor Specification version for your operating system MPS version 1 4 added extended configuration tables to improve support for multiple PCI bus configurations and improve future expandability The default setting is 1 4 OS Select for DRAM gt 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS 2 that depends on certain BIOS calls to access memory The default setting is Non OS 2 Report No FDD For WIN 95 If you are using Windows 95 98 without a floppy disk drive select Enabled to release IRQ6 This is required to pass Windows 95 98 s SCT test You should also disable the Onboard FDC Controller in the Integrated Peripherals screen when there s no floppy drive in the system If you set this feature to Disabled the BIOS will not report the missing floppy drive to Win95 98 Small Logo EPA Show The EPA logo appears at the right side of the monitor screen when the system is boot up The default setting is E
33. r up No errors The system boot will not be halted for any error that may be detected All errors Whenever the BIOS detects a non fatal error the system will stop and you will be prompted All But Keyboard The system boot will not be halted for a keyboard error it will stop for all other errors All But Diskette The system boot will not be halted for a disk error it will stop for all other errors All But Disk Key The system boot will not be halted for a key board or disk error it will stop for all others LL OO LL LL a 16 ET900 Users Manual BIOS SETUP eee Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU Feature Press Enter ITEM HELP Hard Disk Boot Priority Press Enter Virus Warning Disabled Menu Level gt CPU L1 and L2 Cache Enabled Quick Power On Self Test Enabled First Boot Device Floppy Second Boot Device Hard Disk Third Boot Device CDROM Boot Other Device Enabled Swap Floppy Drive Disabled Boot Up Floppy Seek Disabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disabl Typematic Rate Chars Sec 6 Typematic Delay Msec 250 Security Option Setup APIC Mode Enabled MPS Version Control for OS 14 OS Select For DRAM gt 64MB Non OS2 Report No FDD For WIN 95 Yes Small Logo EPA Show Enabled CPU
34. so takes advantage of the high performance Intel processor Intel GMA 950 graphics supports Dual Independent Display technology The main features of the board are Supports COM ETX Type II Module pin out definitions Supports Intel Core Duo Solo processors Supports up to 533 667MHz FSB One DDR2 SDRAM SO DIMM Max 2GB Intel 945GM Express VGA for CRT LVDS Intel 945GM Integrated VGA Supports CRT LVDS Supports up to six x1 PCI E one x16 PCI E four PCI ZZ SS 8S eS L LO ga ET900 Users Manual 1 INTRODUCTION Checklist Your ET900 package should include the items listed below e The ET900 CPU Module e This User s Manual e 1 CD containing the following e Chipset Drivers e Flash Memory Utility SSS SS LLL Laga 2 ET900 Users Manual INTRODUCTION ET900 Specifications COM ETX w Pin Out Type 2 CPU Type Intel Core Duo Solo Mobile Processors CPU Voltage 0 700V 1 5V Up to 1 66GHz or above CPU Operate 533MHz 667MHz FSB Frequency 2MB Green APM APM1 2 CPU Socket BGA CPU on board mPGA 478MT Socket Chipset Intel 945GM Chipset GMCH 82945GM 1466 pin FCBGA ICH7M 82801GBM 652 pin mBGA FWH Award BIOS support ACPI Function DDR2 667 533 SO DIMM x1 w o ECC function Max 2GB VGA 945GM built in supports CRT S VIDEO LVDS 945GM built in supports 18 18 bits single or dual channel LVDS Support TV Out Composite and S Video ICH7M built in 10 100BT MAC Intel EP8256
35. tically returns to the main screen To disable a password just press the lt Enter gt key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup freely Save amp Exit Setup This option allows you to determine whether or not to accept the modifications If you type Y you will quit the setup utility and save all changes into the CMOS memory If you type N you will return to Setup utility Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing Y will quit the Setup utility without saving the modifications Typing N will return you to Setup utility i SS SS SS 5 ET900 User s Manual 33 BIOS SETUP ooo This page is intentionally left blank I OO LL 34 ET900 User s Manual DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98SE Windows ME Windows 2000 and Windows XP The software and drivers are included with the main board If you find the items missing please contact the vendor where you made the purchase The contents of this section include the following Intel Chipset Software Installation Utility 36 VGA Drivers Installation 0 0 0 aaa aaa aaa 38 AC97 Codec Audio Driver Installation IP400
36. tware works correctly with Windows Realtek AC 97 Audio If you want to search for Microsoft digitally signed software visit the Windows Update Web site at http windowsupdate microsoft com to see if one is available Do you want to continue the installation No More Info 40 ET900 Users Manual DRIVERS INSTALLATION 4 Click Finish to restart the computer and for changes to take effect Realtek AC 97 Audio Setup 5 00 Maintenance Complete InstallShield Wizard has finished performing maintenance operations on Realtek AC 97 Audio No will restart my computer later Remove any disks from their drives and then click Finish to complete setup i SS ET900 User s Manual 41 DRIVERS INSTALLATION Intel PRO LAN Drivers Installation Follow the steps below to complete the installation of the Intel PRO LAN drivers 1 Insert the CD that comes with the board Click Intel Chipsets and then Intel R I945GM Chipset Drivers Then click Intel R PRO LAN Network Drivers 2 Click Install Base Software to continue Intel PRO Network Connections Install Base Driver Make Driver Disk View Release Notes 3 When prompted please to restart the computer for new settings to take effect 42 ET900 User s Manual DRIVERS INSTALLATION Marvell LAN Drivers Installation IP400 carrier board only Follow the steps below to complete the installation of the Intel PRO
Download Pdf Manuals
Related Search
Related Contents
WTTP User Guide - Wee Talk Tracker Pro PDF User`s manual of the IR-thermometer Smart ThermoGraph HDS1021M Handheld Digital Storage Oscilloscope ACCORDEUR POLYPHONIQUE Domo DO152A fan 5 - Leks Group Esempio di Certificazione nel settore agro Istruzioni per l`uso KGI 3100/A Copyright © All rights reserved.
Failed to retrieve file