Indesit DV 620 Dishwasher User Manual
Contents
1. The hardness of the water varies from place to place If hard water is used in the dishwasher deposits will form on the dishes and utensils The appliance is equipped with a special softener that uses a Salt specifically designed to eliminate lime and minerals from the water Loading the Salt into the Softener Always use salt intended for use with dishwashers The salt container is located beneath the lower rack and should be filled as follows 1 Remove the lower rack and then unscrew and remove the cap from the salt container 2 If you are filling the container for the first time fill it with water 3 Place the end of the funnel Supplied into the hole and introduce about 2 kg of salt It is normal for a small amount of water to come out of the salt container 4 Carefully screw the cap back on The salt container should be filled after about every 30 wash cycles Warning To prevent rust from forming we advise you to load the salt before starting a wash cycle Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the harness of the water used This is intended to optimize and cus tomize the level of salt consump tion so that it remains at a minimum Your Local Water Board can supply the degree of hardness of the water in your area To adjust salt consumption pro ceed as follows 1 Unscrew the cap from the salt container 2 There is a r2. It may happen that food particles become encrusted on the sprayer arms and block the holes Check the sprayer arms periodically and clean them when needed see Close up View interior letters F I Cleaning the Water Inlet Filter Periodically clean the water inlet filter see figure 2 under Installation located on the outlet of the water supply tap After turning off the water tap unscrew the end of the water supply hose remove the filter and clean it carefully under running water Then return the filter to its place and tighten the water supply hose back into position Error messages Your dishwasher is equipped with a safety system which is able to detect any operating anomalies These anomalies are reported by one or two wash cycle indicator lights G flashing rapidly Take a note of which lights are flashing turn the appliance off and call for technical assistance Tap off alarm If you have forgotten to turn the water tap on your appliance will remind you of this by sounding a few short beeps for a few minutes Turn the tap on and your appliance will start up again after a few minutes Were you to be absent when these beeps are sounded the appliance will be blocked automatically and indicator lights 2 and 3 wash and rinses will flash rapidly Turn the appliance off at the ON OFF button turn on the water tap and wait approximately 20 seconds before turning the appliance back on the selected wash cycle will start
3. is empty by means of indicator D Loading the Rinse Aid To open the dispenser turn the C cap in the anti clockwise direction and then pour in the rinse aid making sure not to overfill The amount of rinse aid used for each cycle can be regulated by turning the F dose adjustor located beneath the C cap with a screwdriver There are 6 different settings the normal dosage setting Is 4 re Important Proper dosage of the rinse aid improves drying If drops of water remain on the dishes or spotting occurs the dosage adjustor should be turned to a higher setting If the dishes have white streaks turn the dosage adjustor to a lower setting Three in one dishwasher tablets are now available on the market and combine the detergent salt and rinse aid all in one If the water in your area is hard or very hard we still recommend you pour extra salt into the relevant dispenser to prevent the formation of white streaks on your dishes or on the appliance interior Add rinse aid to the corresponding container only if you are dissatisfied with the results on your dishes In any case please read the manufacturer s instructions provided on the packet Loading the Dishwasher Before placing the dishes in the dishwasher remove the Lower Rack Upper Rack larger food particles to prevent the filter from becoming clogged which results in reduced performance If the pots and pans have baked on food that is extremely hard to remove
4. part of the pipe marked with the letter A should be between 40 and 100 cm above the ground The pipe should not be immersed in water Attention The special plastic hose support must be solidly fastened to the wallto prevent the drain hose from moving and allowing water to spill outside the drain Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate located on the stainless steel inner door of the appliance and that the electrical system is sized for the maximum voltage on the rating plate insert the plug into an electrical socket which is earthed properly the earthing of the appliance Is a safety requirement mandated by law If the electrical socket to which the appliance must be connected is not appropriate for the plug replace the plug rather than using adpators or the like as they could cause overheating and burns Caution the dishwasher plug must be accessible even when the appliance is installed as a built in unit so that maintenance can be done safely Should the electricity supply cable be damaged we recommend that you only contact authorised Technical Service Centres for the replacement Condensation proof tape On some models a transparent condensation proof adhesive tape has been provided It should be stuck onto the lower side of your wooden worktop to protect it from the formation of condensation Wh
5. we recommend that they be allowed to soak before they are washed This will eliminate the need for extra wash cycles Pull out the racks to facilitate loading the dishwasher How to Use the Lower Rack Werecommend that you place the most difficult to clean items on the bottom rack pots pans lids serving dishes and bowls as shown in the figure to the right It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm Pots serving bowls etc must always be placed top down Deep pots should be slanted to allow the water to flow out Silverware should be placed in the silverware basket This basket is equipped with two removable grids insert the cutlery one by one into the slots knives and utensils with sharp blades or tips should be positioned with the sharp parts at the bottom Position all cutlery items so that they don t touch see figure A Especially long utensils should be placed in the horizon tal position at the front of the upper rack How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware such as glasses coffee and tea cups and saucers as well as plates small bowls and shallow pans as long as they are not too dirty Position the dishes and cookware so that they do not get moved by the spray of water e LL How to adjust the Upper rack ror ze The top rack can be adjusted usi
6. DV 620 Dishwasher Installation and use 1 INDESIT Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual as they provide important information which is essential to safe and proper installation use and maintenance of the appliance This appliance complies with the following EEC directives 73 23 EEC Low Voltage and subsequent modifications 89 336 EEC Electromagnetic Compatibility and subsequent modifications 97 17 EEC Labelling 1 Carefully dispose of the packing material 2 After removing the packing check to make sure that the appliance is not damaged If in doubt contact a qualified professional 3 The dishwasher must only be used by adults for the washing of household dishes and cooking utensils 4 Fundamental rules to follow when using the appliance Never touch the dishwasher when barefoot or with wet hands or feet We discourage the use of extension cords and multiple sockets During installation the power supply cord must not be excessively or dangerously bent or flattened If the appliance is not operating properly or maintenance must be performed disconnect the appliance from the power supply 5 Keep detergents out of the reach of children who must also be kept away from the dishwasher when It is open 6 This appliance cannot be installed outdoors not even if the area in which it is installed is covered by a roof it is als
7. ater supply and leave the door of the appliance slightly ajar This will help the seals last longer and prevent odors from forming within the appliance Moving the Appliance If the appliance must be moved try to keep it in the vertical position If absolutely necessary it can be positioned on its back Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals Periodic cleaning with adamp sponge will prevent this from occuring Cleaning and Special Maintenance The filter assembly If you want consistent good results from your dishwasher you need to clean the filter assembly The food particles are removed from the wash water allowing it to be recirculated during the cycle filtered perfectly For this reason it is a good idea to remove the larger food particles trapped inside the semi circular filter A and cup C after each wash to remove the filter assembly pull the cup handle upwards All you need to do is rinse them under running water The entire filter assembly should be cleaned thoroughly once a month semi circular filter A cup C cylindrical filter B microfilter D To remove filter B turn it anti clockwise Use a small non metallic brush for cleaning Reassemble the filter parts as shown in the figure and reinsert the whole assembly into the dishwasher Position it into its housing and press downwards Troubleshooting lt may occur t
8. en not provided this tape can be requested as a spare part from authorised retailers Electrical Connection Electrical Connection If your appliance is supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instruction below WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Replacing the fuse When replacing a faulty fuse a 13 amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacemente fuse covers If a replacement fuse cover is fitted it must be of the correct colours as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Replacements can be obtained directly from your nearest Service Depot Removing the plug Ifyour appliance has a non rewireable moulded plug and you should wish to remove it to re route the mains cable through partitions units etc please esure that either the plug is replaced by a fused 13 amp re wireable plug bearing the BSI mark of approval Or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itse
9. ence as the appliance is performing that specific phase of the wash cycle These phases are pre wash wash rinses drying Cancelling or modifying a wash cycle in progress You can modify the wash cycle in progress if it has only just started Turn the knob anti clockwise until it reaches the Reset position and after a few seconds you will hear 4 beeps and indicator light G will turn off This isto inform you that all the settings have been cancelled You are now free to re set the correct wash cycle If you have left out a dish You can interrupt the wash cycle by pressing the ON OFF button insert the dish you had forgotten and press the ON OFF button again The cycle will start up from where you interrupted it There s been a power failure Have you opened the dishwasher door The wash cycle stops and then restarts when the electricity comes back on or when you shut the door At the end of the wash cycle The end of the wash cycle is indicated by two short beeps and the flashing of the drying phase indicator light Turn the knob anti clockwise to Reset in order to reset all the settings Turn the appliance off to cut off the electricity supply Turn off the water tap Wait a few minutes before unloading the dishes they are very hot If you wait a little while they dry better thanks to the steam Empty the lower rack first M ake sure the wash cycle has ended before removing the dishes Warnin
10. ensure proper perfor mance Cold Water Connection This electric household appliance should be connected to the water mains using the cold water supply hose provided with the appliance only Do not use a different hose In the event of replacements use original spare parts only Connect the cold water supply hose to a threaded 3 4 gas connector inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place see figure 2 If the water pipes are new or have not been used for an extended period of time let the water run to make sure that the water is clear and free of impurities If this precaution is not taken there is a risk that the water inlet can get blocked and damage the appliance Hot Water Connection The water supply to the appliance can also be connected to the house s hot water line centralised system heating system as long as it does not exceed a temperature of 60 C In this case the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced The connection must be made to the hot water line following the same procedures asthose forthe connection to the cold water line 10 Drain Hose Connection Fit the drain pipe into a drain line with a minimum diameter of 4 cm or place it over the sink Avoid restricting or bending it Use the special plastic elbow provided see fi gure to position it in the best possible way The
11. g If opening the door soon after the end of the programme or during it stand away from the Dishwasher to avoid possible injury from hot steam Wash Cycle Table Dishw asher washing guarantees your dishes will be cleaned in a hygienic setting for safer cleaner results Cycle selection instructions Very dirty dishes pots and pans not to be used with delicate items Normally dirty dishes pots and pans Standard daily cycle Environmentally frien dly cycle with low energy consumption levels suitable for normally dirty pans and dishes Economic fast cycle to be used to on not very dirty dishes right Cycle description Pre wash with hot water at 40 C Extended wash at 65 C 2 Rinses with cold water Rinse with hot water at 65 C Drying Pre wash with cold water Extended wash at 50 C Cold Rinse Rinse with hot water at 70 C Drying 2 Cold pre washes Extended wash at 50 C Hot rinse at 65 C Drying Short wash at 50 C Detergent for pre wash wash 5 25 gr 5 25 gr 5 25 g Rinse Aid Wash cycle duration tolerance 10 120 72 130 after they are used Hot rinse at 50 C 25 gr 24 No drying cycle Pre wash of dishes pots and pans while waiting for the load Short cold wash to prevent food 12 to be completed after the subsequent meal residue from drying on the dishes Energy Saving Tips It is important to try and r
12. hat the dishwasher does not function or does not function properly Before calling for assistance let us see what can be done first have you forgot to press one of the buttons or to perform an essential operation The Dishwasher Does Not Start Have you checked whether the plug is pushed into the socket correctly the power is on in the house the door is closed properly the ON OFF switch ison ON the water supply is turned on The Dishwasher Does Not Load Water Have you checked whether the water is turned on and the hose Is connected properly the water supply to the house is on and has sufficient pressure the water supply hose is crimped or bent the filter for the water supply hose is clogged The Dishes Are Not Clean Have you put the right amount of detergent into the dispenser Is the wash cycle suitable for the dishes you have placed inside the appliance Are the filter and microfilter clean Can the sprayer arms turn freely The Dishwasher Does Not Drain Have you checked whether the drain hose is crimped or bent Lime Deposits or a White Film Form on the Dishes Have you checked whether the lid to the salt container is closed properly the rinse aid dosage Is correct The dishwasher is not to be used without filters Improper replacement of the filters may reduce the efficiency of the wash and even damage your dishwasher Cleaning the Sprayer Arms
13. ing on the container with an arrow on it see figure to the side if necessary rotate the ring in the anti clockwise direction from the _ setting towards the sign based on the hardness of the water being used It is recommended that adjustments be made in accord ance with the following schema Water Water Hardness Autono Selector my position cycles 2 kg Clarke degrees mmg OEA OORE enemies me ete l fe Detergent and Rinse Aid Detergent Detergent specifically intended for use with dishwashers must be used The dispenser must be refilled before the start of each wash cycle following the instructions provided in the Wash Cycle Table The detergent dispenser is located on the inside panel of the door Loading the detergent To open lid A press button B The cleaning detergent should be introduced into the two containers C and D up to the rim After pouring in the detergent replace the lid pressing down until it clicks Dishwasher detergent in tablets is now available on the market in which case you should place one tablet into container D and replace the lid Notice To facilitate closing the cover remove any excess detergent on the edges of the dispenser Warning Rinse Aid This product makes dishes sparkle more as it improves their drying The rinse aid container is situated on the inside of the appliance door you should refill it when you see the container
14. lf you make the pins unusable so that it cannot be accidentally inserted into a socket Instruction for connecting cable to an altenative plug Important the wires in the mains lead are coloured in accordance with the following code Green amp Yellow Earth Blue Neutral Brown Live CAUTION The dishwasher plug must be accessible even when the appliance is installed as a built in unit so that maintenance can be done safely As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminal in your plug proceed as follows connect Green Yellow wire to terminal market E or coloured Green or Green Yellow Connect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black If a 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse A15 amp plug must be protected by a 15 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt about the electrical supply to your machine consult a qualified electrician before use How to connect an alternative plug The wires in this mains lead are coloured in accordance with the following code BLU E N EUTRAL N BROW N LIVE L GREEN AND YELLOW EARTH E GREEN amp 7A lt a BROWN for LO m 13 amp fuse Der CORD GRIP Disposing of the appliance When disp
15. ng the two rack heights top and bottom To adjust the rack open up the tabs that lock the guides and pull out the rack Arrange the rack with the back wheels in either the top or bottom position and then insert it along the guides until the front wheels are on as well Close the tabs to lock the rack in place see Fig F Turning on the Appliance Starting a wash cycle After performing all the operations described in the previous paragraphs turn the water tap on completely and press ON OFF button A you will hear a short beep and indicator light B lights up Now the appliance is on and ready to be programmed Selecting a wash cycle To select the wash cycle turn knob D clockwise until the reference notch on the knob corresponds with the number or symbol for the cycle you wish to set have a look at the wash cycle table on page 7 For a few seconds the indicator light G concerning the pre wash cycle phase begins to flash then it stays permanently on without flashing for another 10 seconds approximately During this time you can modify your choice of wash cycle A short beep will indicate the start of the wash cycle and indicator light G corresponding to the cycle starting phase will light up After a few seconds you will hear a short beep the wash cycle has begun and we do not recommend you change it Cycle phase indicator lights The dishwasher is provided with 4 indicator lights G which come on in sequ
16. o very dangerous to leave it exposed to the rain and elements 7 Do not touch the heating element during or after a wash cycle 8 Do not lean or sit on the door when it is open as this could overturn the dishwasher 9 If the appliance malfunctions turn off water supply to the appliance and disconnect the plug from the wall socket Then consult the section entitled Troubleshooting If you cannot resolve the problem contact a service centre 10 Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock To maintain the EFFICIENCY and SAFETY of this appliance we recommend call only the Service Centers authorized by the manufacturer e always use original Spare Parts Close up View control panel 4 on OFF Button ON OFF Light Handle For Opening Door Cycles Phase Indicator Light Knob For Selecting Cycles Close up View Interior G ra re Hi L i er tai et TAE dra ce A E Upper Rack 4 Bottom Sprayer Arm Top Sprayer Arm Salt Container Cap Rack Height Adjustor Washing Filter Lower Rack Detergent and Rinse Aid Dispenser Technical characteristics Width cm 59 5 Depth cm 57 Height cm 82 Capacity 12 standard place settings M ains water pressure 30 KPa 1MPa 0 3 10 bar Power voltage See data plate Total absorber power See data plate Fuse See data plate Salt Salt
17. osing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above Merloni Elettrodomestici Viale Aristide Merloni 47 60044 Fabriano Italy Tel 39 0732 6611 Fax 39 0732 662501 www merloni com Xerox Business Services DocuTech 10 2003 195040732 00
18. un the dishwasher when it is fully loaded in order to save on energy In order to prevent odors from forming and food from caking onto the dishes you can run the hold cycle Choose the right wash cycle the choice of cycle depends on the type of dishware cookware and utensils being washed and how dirty they are Use the right amount of detergent if you use too much detergent the result will not be cleaner dishes but rather a greater negative impact on the environment There is no utility in rinsing dishes cookware and utensils before placing them in the dishwasher How to Keep Your Dishwasher in Shape After Every Wash After every wash turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside Remove the Plug Before cleaning or performing maintenance always remove the plug from the socket Do not run risks No Solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher do not use solvents or abrasive cleaning products Rather use only a cloth and warm soapy water To remove spots or stains from the surface of the interior use a cloth dampened with water and a little white vinegar or a cleaning product made specifically for dishwashers When You Go on Holiday When you go on holiday it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket turn off the w
19. up again Clogged filter alarm If the appliance is blocked and indicator lights 1 pre wash and 3 rinses flash rapidly this means the filter is clogged by large particles of food residue Turn the appliance off clean the filter thoroughly and reposition it in its seat as illustrated on this page Then turn it back on The selected wash cycle will start up again If despite all these checks the dishwasher still does not function and or the problem persists contact the nearest authorised service centre and provide them with the following information the nature of the problem the model type number Mod and the serial number S N which are indicated on the plate located on the side of the inner part of the door Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts Installation Positioning the Appliance Position the appliance in the desired location The back should rest against the wall behind it and the sides along the adjacent cabinets or wall The dishwasher Is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation Levelling the Appliance Once the appliance is positioned adjust the feet screwing them in or out to adjust the height of the dishwasher making it level In any case the appliance should not be inclined more than 2 If the appliance ts level it will help
Download Pdf Manuals
Related Search