Husqvarna 9030PW Pressure Washer User Manual
Contents
1. 3 Attach a garden hose to the inlet connection for garden hose and connect it to the water supply Use a hose with a minimum inside diameter of 5 8 016 m and a length of 50 ft 15 m or less NOTI CE Some local plumbing codes require backflow prevention when connecting to a fresh water supply Install a backflow preventer upstream from the pump if necessary a If inlet water pressure is over 100 psi install a regulating water valve at the garden hose connection b DO NOT exceed 100 38 C inlet water temperature NOTE The inlet water supply must have a minimum flow rate of 8 gpm 30 lpm or 5 gpm 191 Ipm on 5525PW 4 Turn the water supply ON NOTI CE NEVER run the unit dry Be sure the water supply is completely turned on before operating the unit 5 Squeeze the gun until water sprays from the tip indicating that all air is purged from the system Set the trigger safety latch 6 On model 5525PW Honda GC Engine Open the fuel shutoff valve by turning the knob counterclockwise until it stops Close the choke if engine is cold by pulling the choke lever out The throttle is fixed On models 6026PW and 9030PW Robin Subaru Engines Open the fuel shutoff valve by turning the lever to the downward position Close the choke if the engine is cold by moving the choke lever fully to the left Move the throttle fully to the left to the RUN or RABBIT position Turn the On Off switch to the ON po2. 10W 30 SAE 30W Above 60 F 15 7 C Engine Oil Type Engine Oil Capacity 5525PW Honda GCV160 18 6 fl oz 0 550 L 6030PW Subaru EX17 20 fl oz 0 591 L 9030PW Subaru EX27 37 fl oz 1 09 1335PW Honda GX390 37 fl oz 1 09 L Engine Fuel Capacity 5525PW Honda GCV160 0 29 gal 1 09 L 6030PW Subaru EX17 0 95 gal 3 6 L 9030PW Subaru EX27 1 61 gal 6 1 L 1335PW Honda GX390 1 72 gal 6 5 L Pump Oil Type 5525PW AR Pump Special See pump parts list 6030PW 9030PW 1335PW CAT Pumps Special CAT pump oil See pump parts list DO NOT use any oil in pumps other than the manufacturer s oil Pump Oil Capacity 5525PW AR RM Pump 3 5 oz 0 103 L 6030PW CAT 3DX Pump 8 5 oz 0 251 L 9030PW and 1335PW CAT 66DX Pump 18 oz 0 532 L Pump Detergent Suction Water to detergent ratio 5525 Water to detergent ration 6026PW 9030PW 1335PW 8 to 1 1296 detergent 10 to 1 1096 detergent Water Supply Requirements Minimum inlet pressure 20 psi Maximum inlet pressure 100 psi Maximum inlet temperature Minimum inlet flow rate Use 5525PW 6026PW 9030PW 1335PW Inlet garden hose size Maximum inlet garden hose length 100 F 38 5 18 9 Ipm 2 times the rated flow of unit or 8 gpm 30 3 Ipm 5 8 ID 15 9 mm 50 ft 15 2 m English 19 TROUBLESHOOTING CHART Troubleshooting Chart Gasoline Powered Pres
3. H Husqvarna Operator s manual 5525 6026 9030PW 1335PW Please read the operator s manual carefully and make sure you understand the instructions before using the machine English CONTENTS Contents CONTENTS 1 CONCents 2 542 n3 mad teen phi 1 KEY TO SYMBOLS 2 Symbols in the Operator s Manual 2 INTRODUCTION 3 Dear 3 WHAT IS WHAT 4 What is what on the pressure washer 4 FREQUENTLY ASKED QUESTIONS 5 How do I start my pressure washer 5 What type of oil dol use 5 Why don t have any water pressure 5 How get high pressure 5 How do get the soap suction to work 5 Why doesn t the pressure washer apply detergents with high pressure 5 What maintenance do need to perform on my pressure washer 5 Where can buy accessories for my pressure washer 5 SAFETY GUIDELINES 6 Important Safety Guidelines 6 PRE OPERATION 8 UNPACKING doe dp mid xo ethos 8 2556 18 6 doses oles hope aod iut BORD MU Ee 8 Trigger Safety Latch 10 OPERATION 11 1 Surface preparation 11 2 Start UD t can t
4. gun is triggered 3 After using detergents flush the suction system by placing the detergent suction tube into a bucket of clean water 5 Cleaning Power The easiest way to regulate the cleaning power of your pressure washer is by changing the distance from the surface you are cleaning Begin spraying with a wide fan pattern while standing several feet from the surface Slowly move closer to the object you are cleaning adjusting the spray pattern as necessary until you find the most effective cleaning technique NOTE Some units also may have a pressure adjustment knob on the pump that can adjust the pressure models 9030PW and 1335PW 6 Final Rinse The final rinse should start at the bottom and work upward Make sure that you thoroughly rinse the surface and that you remove all detergent 14 English PRESSURE RELIEF PROCEDURE To reduce the risk of bodily injury or property damage ALWAYS follow this procedure whenever spraying is stopped when work is completed and before checking or repairing any part of the system 1 Engage the trigger safety latch Turn the unit off 2 3 Shut off the water supply 4 Disengage the trigger safety latch and trigger the gun to relieve pressure Re engage the trigger safety latch Before overnight storage long term storage or transporting unit disconnect the water supply and turn off the fuel supply valve 7 Shutdown 1 Be sure all detergent is flushed
5. knob located on the pump see Figure 11 Turn the knob clockwise to increase the pressure Turn the knob counter clockwise to decrease the pressure DO NOT try and force the knob to turn The knob may already be at either the lowest or highest setting Pull collar back If there is not a plastic adjustment knob located on the pump See Figure 11 then the pressure cannot be adjusted The only way to adjust the pressure is to move closer or further away from the cleaning surface and adjust the spray fan angle as shown in the next section Figure 12 Installing Quick Connect Tip A narrow stream has high impact force on the cleaning surface and results in maximum deep cleaning in a concentrated area However this narrow high impact spray can damage some surfaces so use it cautiously Not recommended for use on automotive paint trim and vinyl siding Figure 11 Camshaft pump pressure adjustment Figure 13 Narrow high impact stream ADJUSTING THE SPRAY FAN ANGLE A wide fan pattern will distribute the impact of the Your unit has quick connect tips that have a range water over a larger area resulting in excellent of spray fan angles Model 5525PW includes the cleaning action with reduced risk of surface black detergent and yellow 15 quick connect tips damage Clean large surface areas quickly using a only wide fan pattern The quick connect tips can be switched out from a 0 narrow high impact stream to a 65 wide fan spr
6. models 5525W and 6026W connect clear plastic Remove the equipment and all parts from the hose to hose barb on detergent tank See Figure 2 carton The carton should contain the following On models 1335PW and 9030PW connect to brass e One pressure washer pump engine cart base barb on pump See Figure 3 One cart handle assembly e One spray gun One lance Two spray tips for Model 5525PW Five spray tips for Models 1335PW 6026PW and 9030PW One high pressure hose One pack of nuts bolts and manuals e One bottle of engine oil If any parts are missing Please contact your Husqvarna dealer After unpacking the product inspect it carefully for any damage that may have occurred during transit Make sure tighten fittings and bolts before using Figure 2 Connect detergent hose to detergent tank the pressure washer DO NOT operate the unit if it s AWARNING damaged during shipping handling or use Damage could result in bursting and cause injury or property damage ASSEMBLY Use 1 2 13 mm wrench to assemble pressure washer On model 5525PW use two adjustable or 7 16 wrenches 1 Slide the handle assembly over the lower legs of the cart base Use the standard nut and bolt to secure the legs See Figure 1 Figure 3 Connect detergent hose to brass barb 3 Secure garden hose not included to the inlet connection on pump See Figures 4 and 5 Figure 1 Assemble Handle H
7. ut 7 2 4 531 30 75 06 1 Eco P O 531 30 75 10 531 30 75 08 P O 531 30 75 06 x1 Key P O Part Of KIt 26 English 6026 531 30 75 12 Pump Assembly Complete 1 531 30 75 77 x3 _ 531 30 75 88 a 2531 30 75 78 kw 22531 30 75 79 E M V 531 3075 80 on 727531 30 75 81 lt 531 30 75 87 2531 30 75 82 x3 D oY 40 42531 30 75 83 531 30 75 14 1 of 531 30 75 84 7 f Fa 4 9009 ato 531 30 75 51 3 n 531 30 75 15 3 8 TRV 6 531 30 75 91 1 4 TRV to E 531 30 75 66 531 30 75 85 x3 531 30 75 16 8 531 30 75 57 531 30 75 86 x3 531 30 75 56 1 i x ut s Eur s a arl us x Fon LO a E al 2 n F T e x P ana TES ua P is J B 531 30 75 90 531 30 75 97 531 30 74 90 a 531 30 75 89 531 30 75 67 531 30 75 69 531 30 75 70 531 30 75 71 531 30 75 72 777 531 30 75 73 C 531 30 75 74 531 30 MI 531 30 75 76 531 30 75 54 531 30 75 55 531 30 74 83 Pump Oil not shown Key P O Part Of English 27 Pump 9030PW 1335PW 531 30 75 17 Pump Assembly Complete P O 531 30 75 61 x1 Ae SD e LI US
8. when operating or performing maintenance NEVER put hand or fingers over the spray tip while operating the unit NEVER try to stop or deflect leaks with any body part 6 English e ALWAYS engage the trigger safety latch in the safe position when spraying is stopped even if only for a few moments ALWAYS follow detergent manufacturer s label recommendations for proper use of detergents ALWAYS protect eyes skin and respiratory system from detergent use DO NOT use AWARNING pressure that exceeds the operating pressure of any of the parts hoses fittings etc in the pressurized system Ensure all equipment and accessories are rated to withstand the maximum working pressure of the unit Explosion hazard AWARNING e NEVER spray flammable liquids or use pressure washer in areas containing combustible dust liquids or vapors e NEVER operate this machine in a closed building or in or near an explosive environment e DO NOT remove fuel tank cap or fill fuel tank while engine is hot or running allow engine to cool two minutes before refueling ALWAYS fill the tank slowly e NEVER disconnect the high pressure discharge hose from the machine while the system is pressurized To depressurize machine turn power and water supply off then press the gun trigger 2 3 times NEVER permanently engage the trigger mechanism on the gun NEVER operate the machine without all components pro
9. windows with a narrow high impact stream Doing so may break the window The most sure way to avoid damaging surfaces is to follow these steps 1 Before triggering the gun make sure the quick connect tip you are using is appropriate for the application The color of the tip shows what spray angle it is Red 0 Maximum Duty Yellow 15 Heavy Duty Green 25 General Duty White 40 Light Duty Black 65 Low Pressure Detergent 2 Place the spray tip approximately 4 5 feet 1 22 1 52 m away from the cleaning surface Then hold the lance and spray tip at a 45 degree angle to the cleaning surface Trigger the gun 3 Vary the fan pattern spray angle and the distance to the cleaning surface until optimum cleaning efficiency is achieved without damaging the surface 4 Detergent Application NOTE Use only detergents formulated for pressure washers NOTE Test detergent in an inconspicuous area before use NEVER replace quick connect tip AWARNING when gun is triggered DETERGENTS The use of detergents can dramatically reduce cleaning time and assist in the removal of difficult stains Many detergents are customized for pressure washer use on specific cleaning tasks Pressure washer detergents are as thick as water Using thicker detergents like dish soap will clog the chemical injection system and prevent the application of the detergent Once applied to a cleaning surface detergents take time to b
10. 0 37 fl oz 1 09 L 16 English Plug Models 1335P 6026PW and 9030PW Engine Oil Drain Plug Figure 18 MAINTENANCE CHECKING PUMP OIL AND PUMP OIL CHANGING Checking oil level Most pumps have either a sight glass or a dipstick or both to check the pump oil level The correct oil level is at the center of the sight glass center of red dot The sight glass is usually located on the back side of the pump See Figure 19 B Figure 19 Pump Oil Filler Vent Cap A Sight Glass B and Drain Plug C Locations For model 5525PW Pump is factory sealed Changing or refilling the oil in the pump requires removal of the pump from the engine and should not be required unless oil has leaked out due to worn or damaged oil seals in the pump If oil has leaked out of the pump bring the pressure washer to a certified service center for repair For models 6026PW 9030PW and 1335PW These units all have a sight glass to check the oil level and have a drain plug to remove the old oil when changing To add oil remove vent cap from top of pump See Figure 19 Changing oil Remove the oil drain plug located at the backside of the pump See Figure 19 C Drain old oil Replace drain plug Refill pump with the correct type and amount of oil see below for oil types and amounts Check oil level Upon starting the pressure washer check for any pump oil leaks Pump Oil Type 5525PW AR Pump Special See p
11. 75 39 x1 531 30 74 61 x1 531 30 75 34 531 30 75 32 531 30 74 92 531 30 75 33 531 30 75 40 2 531 30 74 60 Detergent Tube not shown 24 English 9030PW and 1335 531 30 74 67 d 531 30 74 82 531 30 74 87 531 30 74 88 0 8 531 30 74 64 9030PW 531 30 74 82 531 30 74 65 1335PW 531 30 74 89 f 531 30 75 44 531 30 74 86 SSSSSSSSSSSSSSSZS Ilii 2222222222272 1 531 30 74 68 531 30 74 72 531 30 74 84 531 30 74 77 531 30 74 73 0 a og p 531 30 74 74 15 orto o 531307475 25 531 30 74 76 409 og 531 30 74 70 531 30 75 45 x4 9030PW 531 30 75 48 x1 531 30 75 96 x4 1335PW 531 30 74 66 x1 531 30 75 49 x2 531 30 75 50 x6 531 30 74 95 531 30 75 40 x2 531 30 75 47 531 30 74 91 531 30 74 61 x1 531 30 75 39 x1 531 30 74 71 Detergent Tube not shown English 25 Pump for 5525PW 531 30 75 29 Pump Assembly Complete o 0 000 09 531 30 75 04 531 30 75 01 x6 4 531 30 75 02 x6 531 30 75 03 x3 130 75 05 531 30 75 66 N C 531 30 75 03 x3 531 30 75 07 3 531 30 75 02 x6 My e P O 531 30 75 01 x3 KS dl 531 30 74 99 a 127 B 531 30 75 00 x3 P O 531 30 75 10 0 1008 P O 531 30 75 01 x3 Sit 531 30 75 11 531 30 74 98 9 2 2 2 bd
12. MBOLS Safety Guidelines This manual contains information that is very important to know and understand This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS To help recognize this information observe the following symbols Warning indicates a potentially AWARNING hazardous situation which if not avoided COULD result in death or serious injury ACAUTION Caution indicates a potentially hazardous situation which if not avoided MAY result in minor or moderate injury N OTI CE Notice indicates important information that if not followed may cause damage to equipment NOTE Information that requires special attention 2 English Symbols in the Operator s Manual Please read the operator s manual carefully and make sure you understand the intructions before using the tool DO NOT overreach or stand on unstable support Keep good footing and balance at all times Risk of injection or severe injury Keep clear of nozzle ALWAYS wear safety glasses or goggles and protective equipment hearing protection gloves rubber boots protective clothing when operating or performing maintenance Risk of explosion Risk of fire 7 INTRODUCTION Dear Customer Congratulations on your choice to buy a Husqvarna product Husqvarna is based on a tradition that dates back to 1689 when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna Ri
13. ak eae 11 3 Initial High Pressure Rinse 12 Pressure Adjustment 12 Adjusting the Spray Fan Angle 12 Angle to the Cleaning Surface 13 Distance from Cleaning Surface 13 How to Avoid Damaging Surfaces 13 IN466700AV 7 06 4 Detergent Application 13 55905 3 2 13 General Cleaning Tips 14 5 Cleaning Power 14 14 Z ShUtdOWLD 14 Pressure Relief Procedure 14 9 STORAGE 15 Long Term Storage Instructions More than 30 days in storage 15 Tips for Extending the Life of Your Pressure Washer 15 MAINTENANCE 16 Engine Oil Changing Instructions 16 Check Pump Oil and Pump Oil Changing 17 MAINTENANCE SCHEDULE 18 TECHNICAL AND CONSUMER INFORMATION 19 TROUBLESHOOTING CHART 20 CART PARTS LIST 23 DOL OPV eost iaa Ea 23 6026PVW Cart eats th 24 et tores tears Be eis 25 1335P VV Cabe Retos teres 25 PUMP PART LIST 26 552 be he 8 etti 26 6026PVWV PUMP ext imt dalai 27 PUMP 21er ex EE rm ne Eten 28 1335 PV PUMD 28 English 1 KEY TO SY
14. ay The color of the tip shows what spray angle it is Red 0 Maximum Duty Yellow 15 Heavy Duty Green 25 General Duty White 40 Light Duty Black 65 Low Pressure Detergent Figure 14 Wide fan pattern 12 English ANGLE THE CLEANING SURFACE When spraying water against a surface you can generate maximum impact by striking the surface head on However this type of impact can cause dirt particles to embed in the surface and can prevent the desired cleaning action Spray water against a surface at a 45 degree angle to achieve the most beneficial impact force and to efficiently remove debris coUe er n DTT AZIZ gt D D 5 c 4 at a Figure 15 Optimum angle to cleaning surface DISTANCE FROM CLEANING SURFACE The distance between the spray nozzle and the cleaning surface is another factor that affects the impact force of the water The impact force of the water increases as the nozzle is moved closer to the surface HOW TO AVOID DAMAGING SURFACES Damage to cleaning surfaces occurs because the impact force of the water exceeds the durability of the surface You can vary the impact force by controlling the spray tip angle to the cleaning surface and the distance from the cleaning surface and by changing the spray tip NEVER use a narrow high impact stream on a surface that is susceptible to damage Avoid spraying
15. et or discharge valve or worn inlet and or discharge valves yy Wa Corrective 5 Fill the tank with fuel shut off valve Check fuel line and carburetor Check oil level Fill if necessary Move switch to start position Drain fuel tank and carburetor Use new fuel and dry spark plug Remove and clean or replace Clean adjust the gap or replace Trigger spray gun See engine owner s manual Remove and clean or replace Clean adjust the gap or replace Drain fuel and carburetor Use new fuel Replace with tip of proper size Clean Check more frequently Check filter Replace water seals See service center Clean inlet and discharge valve assemblies Check filter Check garden hose may be collapsed or kinked Check inlet water flow Replace worn valves Replace high pressure hose Ensure hoses and fittings are tight Check and replace Check water temperature may not exceed 100 F 38 C Install new water seals See service center 6 Change oil as specified in maintenance schedule Install new oil seals See service center Install new water seals See service center Install new plungers See service center Install proper filtration on pump inlet plumbing Check water temperature may not exceed 100 F 38 C DO NOT modify any factory set adjustments Clean or replace tip NEVER run pump more than 2 minutes without spraying DO NOT run pump wi
16. from system 2 Turn the engine OFF 3 Turn the water supply OFF 4 After the engine and water supply are turned OFF trigger the gun to depressurize the system N OTI CE NEVER turn the water supply off before turning the engine motor off Serious damage could occur to the pump andlor engine motor ACAUTION NEVER disconnect the high pressure discharge hose from the machine while the system is pressurized To depressurize turn engine motor off turn water supply off and squeeze gun trigger 2 3 times 5 After each use when engine has cooled wipe all surfaces of the pressure washer with a clean damp cloth e DO NOT store the pressure washer outdoors e DO NOT store the pressure washer where it might freeze unless it has been properly winterized 8 Storage LONG TERM STORAGE INSTRUCTIONS MORE THAN 30 DAYS IN STORAGE 1 Remove fuel from the tank and run the pressure washer in a normal operating mode until the engine stops from a lack of fuel Normal operating mode means actually spraying water from the gun while the engine is running Alternate method Add fuel stabilizer to gas in the tank and run in normal operating mode for at least five minutes 2 Stop the engine turn off the water supply and trigger the gun to release pressure in the high pressure hose 3 Disconnect the water supply and high pressure hose from the pump 4 Allow the engine to cool 5 Disconnect the spar
17. igh Pressure Figure 4 Secure garden hose 8 English 4 Connect high pressure hose to the pump outlet See Figure 5 High Pressure Hose Pull collar back Garden Hose Figure 5 Connect high pressure hose to pump 5 Attach the lance with nozzle to the gun See Figure Figure 7 Quick Connect Tip For models 5525PW and 6026PW Insert spray tips into the rubber tip holder Then attached the tip holder to handle by wrapping around and inserting tail end through hole to secure See Figure 8 Figure 6 Attach lance to gun 6 Install quick connect tip by pulling back on collar and pressing in tip Release collar make sure it completely returns to its forward position and tip is secure See Figure 7 Figure 8 Insert spray tips into the rubber tip holder English 9 models 9030PW and 1335PW Insert spray tips TRIGGER SAFETY LATCH into rubber grommets on placard See Figure 9 In the engaged position the trigger safety latch prevents the gun from being triggered accidentally Pull the latch up to engage it See Figure 10 ALWAYS engage the trigger safety latch when the unit is not in use Trigger lock not engaged Figure 9 Insert spray tips into the placard Trigger lock engaged Figure 10 Trigger lock 10 English 1 Surface Preparation ALWAYS engage the trigger safe
18. ith initial purchase of pressure washer Detergent suction will not function if more than once section of hose is attached to unit Remove 1 2 54 cm tapered detergent barb from pump Clean the barb and make sure that ball and spring are properly aligned with tapered portion of the spring facing the ball The ball should be on top of the spring English 21 5 22 English 5525PW du p 531 30 74 62 531 30 75 35 o 531 30 74 78 0 og a 531 30 74 79 15 og 7 531 30 74 80 25 531 30 74 72 531 30 74 84 531 30 74 81 40 of 531 30 75 36 531 30 74 94 531 30 75 41 x4 531 30 75 37 531 30 75 41 x2 531 30 81 12 531 30 75 43 4 531 30 81 14 531 30 75 28 531 30 75 39 1 531 30 81 13 531 30 74 61 1 531 30 75 31 531 30 81 15 531 30 75 32 1 531 30 75 30 531 30 81 11 531 30 75 38 Detergent Tube not shown Tips sold separately contact your dealer to purchase English 23 6026 531 30 74 93 pd 531 30 74 97 531 30 74 82 Sa 531 30 74 87 531 30 74 82 0 531 30 74 63 531 307488 277 531 30 74 89 B 531 30 75 44 531 30 74 86 531 30 74 77 Soap 531 30 74 78 0 o 531 30 74 79 15 531 30 74 80 25 531 30 74 72 531 30 74 84 od 531 30 74 81 40 og 531 30 75 36 531 30 74 94 531 30 75 41 x4 531 30 75 41 x2 531 30 75 42 x5 531 30 75 45 x4 531 30
19. k plug wire and remove the spark plug 6 Pour 1 2 oz of engine oil into the spark plug hole NEVER pull the WARNING starter rope on the engine when the spark plug is removed unless the spark plug hole is covered Fuel vapor from the hole can ignite by a spark j 7 Place a rag over the spark plug hole and slowly pull the starter rope several times to distribute the oil Disconnect the high pressure hose from the pump Insert a 12 to 14 piece of garden hose into the pump inlet 10 Place a funnel in the other end of the garden hose N OTI CE Read the manufacturer s instructions for safe handling and disposal of RV antifreeze 11 Pour approximately 6 oz of RV antifreeze into the funnel 12 Pull the starter rope several times until the RV antifreeze comes out of the pump outlet 13 Disconnect the high pressure hose from the gun and drain the hose Hold the gun and lance in a vertical position and squeeze the trigger to drain the water Never store the pressure washer ACAUTION with gasoline in the tank inside a building where fumes may reach an open flame or spark Allow the engine to cool before storing in any enclosure NOTE To winterize unit please follow the same intructions for Storage TIPS FOR EXTENDING THE LIFE OF YOUR PRESSURE WASHER NEVER operate the unit without water Your pressure washer is not meant to pump hot water NEVER connect your pressure washer to a hot water supply a
20. known to the State of California to cause cancer birth defects or other reproductive harm AWARNING When using this product basic precautions should ALWAYS be followed including the following Read all instructions before using the product To reduce the risk of injury close supervision is necessary when the product is used near children Follow all safety codes as well as the Occupational Safety and Health Act OSHA e Ensure safety devices are operating properly before each use DO NOT remove or modify any part of the gun or unit Know how to stop this product and bleed pressure quickly Be thoroughly familiar with the controls e Stay alert watch what you are doing e DO NOT operate the product when fatigued or under the influence of alcohol or drugs Keep operation area clear of all persons e DO NOT overreach or stand on unstable support Keep good footing and balance at all times e Follow the maintenance instructions specified in the manual Risk of injection or AWARNING severe injury Keep clear of nozzle DO NOT discharge streams at persons This product is to be used only by trained operators ALWAYS remove lance from gun before cleaning debris from tip e Keep clear of nozzle NEVER direct high pressure spray at a person animal or yourself e ALWAYS wear safety glasses goggles and protective equipment hearing protection gloves rubber n boots protective clothing
21. oduct and that it will be your companion for long time Think of this operator s manual as a valuable document By following its content using service maintenance etc the life span and the second hand value of the machine can be extended If you will sell this machine make sure that the buyer will get operator s manual Thank you for using a Husqvarna product Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice For customer assistance call 704 921 7000 or contact us at our website www husqvarna com English 3 WHAT 15 WHAT 5525PW 6026PW 9030PW 1335PW 1 Serial Number Product Decal 9 Engine Oil Fill 2 Holder with Spray Tips 10 Engine switch On Off 3 Detergent Tank 5525PW 6026PW 11 Throttle Control 4 Injection Tube not shown 12 Muffler 5 Gun with trigger 13 Choke 6 Lance 14 Fuel Tank 7 Inlet Connection for High Pressure Hose 15 Pressure Adjusting Knob models 9030PW not shown on 9030PW 1335PW 1335PW 8 Inlet Connection for Garden Hose 16 Fuel Valve On Off not shown on 9030PW 1335PW 4 English FREQUENTLY ASKED QUESTIONS How do I start my pressure washer 1 Make sure you have gas and oil in the engine 2 Turn the water then squeeze the trigger on the gun to make sure the water will flow smoothly out of the nozzle or tip UJ Put the engine throttle cont
22. perly connected to the machine handle gun wand assembly nozzle etc Keep hose away from sharp ACAUTION objects Bursting hoses may cause injury Examine hoses regularly and replace if damaged DO NOT attempt to mend a damaged hose Equipment damage NOTICE d ALWAYS turn water supply ON before turning pressure washer ON Running pump dry causes serious damage e DO NOT operate the pressure washer with the inlet water screen removed Keep screen clear of debris and sediment NEVER operate pressure washer with broken missing parts Check equipment regularly and repair or replace worn or damaged parts immediately SAFETY GUIDELINES Use only the nozzle supplied with this machine NEVER leave the wand unattended while the machine is running NEVER tamper with the engine governor or attempt to alter factory settings Altering factory settings could damage the unit and will void the warranty ALWAYS hold gun and wand firmly when starting and operating the machine NEVER allow the unit to run with the trigger released off for more than two minutes Resulting heat buildup will damage the pump NEVER store the pressure washer outdoors or where it could freeze Freezing temperatures can seriously damage the pump Release the trigger when changing from high to low pressure modes Failure to do so could result in damage to the nozzle English 7 UNPACKING 2 On
23. pressure detergent For Other Units 1 Attach clear plastic tube to brass barb on pump see Figure 3 2 Put the other filter end of the clear tube into the detergent container 3 Install the black spray tip to apply low pressure detergent Why doesn t the pressure washer apply detergents with high pressure The reason you don t apply detergents with high pressure is that the detergents bounce off the cleaning surface as fast as you apply them Detergent is only effective when you allow it time to work on the surface of whatever you are cleaning You can only apply detergent at low pressure wait 1 3 minutes to allow it to work and rinse the surface with high pressure What maintenance need to perform on my pressure washer 1 After turning off the pressure washer and the water depressurize the hose by triggering the gun 2 Remove the garden hose and high pressure hose from the pump 3 Pull the start rope slowly five times to purge water from the pump This will help protect the pump from damage 4 DO NOT store your pressure washer in an area where the temperature will drop below 32 F 0 C unless pressure washer is properly winterized see Page 15 Where can buy accessories for my pressure washer Call your local Husqvarna Dealer English 5 SAFETY GUIDELINES Important Safety Instructions SAVE THESE INSTRUCTIONS The engine exhaust from AWARNING this product contains chemicals
24. reak down dirt and grime Detergents work best when applied at low pressure You can effectively clean surfaces by combining the chemical action of detergents with high pressure rinses On vertical surfaces apply the detergent starting at the bottom and work your way upward This method prevents the detergent from sliding down and causing streaks Begin high pressure rinsing at the bottom and work your way upward Figure 16 Quick Connect Tip English 13 On particularly tough stains use a brush in combination with detergents and high pressure rinsing 1 Follow manufacturer s label directions for mixing correct concentrations of soap detergents The soap detergent to water ratio through the pump is approximately 10 1 to 10 2 Insert the filter end of the clear plastic detergent tube into the detergent container Models 9030PW and 1335PW 3 Use the BLACK 65 quick connect spray tip all models See Figure 16 GENERAL CLEANING TIPS 1 Apply the detergent so that it thoroughly covers the cleaning surface Apply the detergent from bottom to top to prevent the detergent from sliding down and streaking Wait a couple of minutes for the detergent to break down the dirt and grime Use a brush to lightly scrub heavily soiled areas NEVER allow the detergent to dry on the cleaning surface 2 Replace black 65 quick connect tip with another color tip NEVER replace quick connect tip AWARNING when
25. rol in the Fast Start position Set the fuel valve to ON Set the On Off switch to ON if applicable 4 Close the choke Squeeze and hold the trigger to relieve any back pressure in the pump while pulling the starter cord Ul Oo If the engine does not start after three tries see Troubleshooting Section Pages 20 21 What type of oil do use ENGINE THE ENGINE DOES NOT COME FILLED WITH OIL For engine oil types and quantities refer to Pages 16 and 19 of this manual and also refer to the included engine owner s manual for oil changing instructions PUMP See Page 17 for pump oil types and quantities Please note the 5525PW model has a pump that is sealed and does not require service Why don t I have any water pressure e s the water hose attached to the pressure washer Is the water turned on Check for any kinks leaks or blockage in the hoses fittings or the nozzle Is the inlet filter screen free of debris Check and remove debris if needed e s the quick connect tip in place See Page 9 How do I get high pressure Use any color tip except black The black tip is only used for low pressure detergent application How do I get the soap suction to work For Detergent Tanks 1 Attach clear plastic tube to plastic barb on detergent tank see Figure 2 2 Fill detergent tank with detergent formulated for use with pressure washers 3 Install the black spray tip to apply low
26. s it will significantly reduce the life of the pump e Running the unit for more than two minutes without spraying water causes heat to build up in the pump Running the unit without spraying water can damage pump components Release the trigger prior to switching the lance between high and low pressure Failure to do so may reduce the life of the o rings in the lance English 15 MAINTENANCE Observe regular maintenance intervals to ensure maximum performance and life from the pressure washer Refer to the schedule for recommended maintenance you operate the pressure washer in dusty conditions perform maintenance checks more often ENGINE OIL CHANGING INSTRUCTIONS Before tipping the engine or ACAUTION equipment to drain oil drain fuel from the fuel tank NOTE Change oil while the engine is cool 1 Disconnect the spark plug wire from the spark plug 2 Locate and remove the engine oil drain plug see Figure 18 3 Drain old oil Replace the drain plug and set the unit upright 5 Refill the unit with new oil of a recommended type and quantity Fill the unit to the proper level shown on the dipstick if provided Otherwise fill the unit to the top of the oil filler neck Engine Type SAE 10W 30 SAE 30W Above 60 F 15 7 C Engine Oil Capacity 5525PW Honda GCV160 18 6 fl oz 0 550 L 6030PW Subaru EX17 20 fl oz 0 591 L 9030PW Subaru EX27 37 fl oz 1 09 L 1335PW Honda GX39
27. sition On model 1335PW Honda GX engine Open the fuel shutoff valve by pushing the lever to the right Close the choke if the engine is cold by moving the choke lever fully to the left Move the throttle fully to the RUN or RABBIT position Turn the On Off switch to the ON position 7 Start the engine If the engine is cold completely close the engine choke If the engine is warm leave the choke open or just partially closed Unlock the trigger safety latch on the gun Grasp the starter rope and brace one foot on the chassis While squeezing the trigger on the gun pull the starter rope rapidly and firmly Continue holding the rope as it returns Repeat these steps until the engine starts In cool weather the choke may have to be kept closed for 10 to 30 seconds to keep the engine running Otherwise open the choke as soon as the engine starts When pulling the starter rope ACAUTION make hand and arm clear of the engine and cart components NEVER let the starter rope NOTICE return by itself Doing so could jam the recoil system English 11 3 Initial High Pressure Rinse After the engine starts trigger the gun 3 to 5 times to get any trapped air out of the system After the spray becomes constant you may need to adjust the pressure see pages 13 and 14 for cleaning techniques PRESSURE ADJUSTMENT Models 9030PW and 1335PW have a pressure adjustment
28. sure Washers Only Symptom Engine will not start or is hard to start Engine misses or lacks power Low pressure and or pump runs rough Water leakage from under pump manifold Water in pump crankcase milky oil Frequent or premature failure of the pump water seals Strong surging at the inlet and low pressure 20 English 1 ONPE e pria gli Sm Possible Cause s No gasoline in fuel tank or carburetor Low oil Start Stop switch in stop position Water in gasoline or old fuel Dirty air cleaner filter Spark plug dirty wrong gap or wrong type Spray gun closed Other causes Partially plugged air cleaner filter Spark plug dirty wrong gap or wrong type Bad Fuel Worn or wrong size tip Inlet filter on pump clogged Worn water seals abrasives in water or natural wear Fouled or dirty inlet or discharge valves Restricted inlet Worn inlet or discharge valves Leaking high pressure hose Pump drawing in air Unloader valve seat faulty or worn Inlet water temperature too high Worn water seals SONO 6 7 Humid air condensing inside crankcase Oil seals leaking Water seals leaking Scored damaged or worn plungers Abrasive material in the fluid Inlet water temperature too high Overpressurizing pump Excessive pressure due to partially plugged or damaged tip Pump running too long without spraying Pump running dry Foreign particles in the inl
29. t r 4 531 30 75 92 i x1 531 30 75 61 1 531 30 75 61 1 28 E 531 30 75 27 NL P O 531 30 75 61 531 30 75 61 b Q eed P m x1 P O 531 30 75 61 x1 sa SA e P O 531 30 75 92 1 p 531 30 75 93 531 30 75 92 1 531 30 75 92 1 531 30 75 61 1 531 30 75 63 1 531 30 75 19 ee A P O 531 30 75 65 x4 E P O 531 30 75 64 P O 531 30 75 63 x4 531 30 75 22 x1 531 30 75 58 6 P O 531 30 75 65 531 30 75 23 X1 bti P O 931 30 75 63 531 30 75 68 2544 531 30 75 58 6 531 30 75 63 S 531 30 75 22 x1 531 30 75 97 531307559 po 531 30 75 62 x x1 gt ee 531 30 75 60 x1 P O 531 30 75 63 531 30 75 24 lt 531 30 75 18 9 531 30 75 26 531 30 74 83 Pump Oil not shown Key P O Part Of 531 30 75 20 x1 531 30 75 21 x1 531 30 75 25 28 English H Husqvarna For customer assistance contact us at our website www usa husqvarna com IN466800AV 3 06
30. thout water Clean or replace valves See service center Symptom Oil leakage between the engine and the pump Fluctuating pressure Pressure drops after period of normal use Pump noisy pump runs rough Pressure washer will not spray detergent TROUBLESHOOTING CHART Possible Cause s Worn oil seals and or o ring DN Sri PN Low engine oil Pump valve worn dirty or stuck Pump drawing in air Tip clogged Worn pump water seals Spray tip worn Pump valve worn dirty or stuck Unloader valve seat worn or dirty If using high pressure soap lance accessory nozzle in low PSI position Pump drawing in air low water supply Valves dirty or worn Worn bearings Water too hot Not using quick connect detergent tip Clog kink or hole in detergent suction hose High pressure hose length too long Detergent injector clogged Corrective Action s Replace oil seals and or o ring See service center ERRO mu IV Add oil Check and replace Ensure hoses and fittings are tight Purge air from garden hose Check or replace Check and replace Check and replace Check clean or replace Check clean or replace Pull back nozzle to high pressure position Ensure fittings are tight Increase water pressure Check clean or replace Check and replace Reduce temperature below 100 F 38 Use black quick connect detergent tip If clean unkink or replace hose Use only hose length provided w
31. ty latch when unit is not in use The following cleaning procedure will help you organize your cleaning task and ensures that you will achieve the best results in the shortest amount of time Remember to use the spraying cleaning techniques mentioned in the following section Before starting a pressure washer cleaning job prepare the surface you intend to clean Clear furniture from the area and make sure that all windows and doors are closed tightly Also protect all plants and trees near the cleaning area with a drop cloth A covering ensures that your plants won t be sprayed by the detergents 2 Start Up ALWAYS use this start up procedure to ensure that the unit is started safely and properly NOTI CE If water has frozen in the pressure washer thaw the pressure washer in a warm room before starting DO NOT pour hot water on or into the pump internal parts will be 1 Check engine oil levels Add oil as necessary NOTE Some units are equipped with a low oil sensor that shuts the engine off if the oil level falls below a certain level If the unit stops unexpectedly check both the oil and fuel levels Check the oil level each time you refuel the unit 2 Check fuel level Add unleaded gasoline rated 86 octane or higher as required DO NOT refuel a AWARNING hot engine Refueling a hot engine could cause a fire Use only fresh clean unleaded gasoline Close the fuel shutoff valve during refueling
32. ump parts list 6030PW 9030PW 1335PW CAT Pumps Special CAT pump oil Use 531 30 74 83 DO NOT use any oil in pumps other than the manufacturer s oil English 17 MAINTENANCE SCHEDULE Maintenance Schedule Action needed Each use e Check water inlet screen and filter Check engine and pump oil levels Fill as necessary Cannot check pump oil on the 5525PW Check gasoline level Fill as necessary After first 5 hours of operation e Change engine break in oil Use SAE30 or 10W 30 detergent oil if below 60 F 15 7 After first 50 hours of operation e Change pump oil Cannot check or change pump oil on the 5525PW Every 25 hours of operation e Change engine oil if operating under heavy load or high ambient temperature e Remove and clean foam pre cleaner or foam air filter if applicable Wash with water and mild detergent Dry thoroughly Rub with oil and squeeze to distribute oil Every 50 hours of operation e Change engine oil e Replace spark plug Each 100 hours of operation or every 3 e Clean or replace paper air cleaner cartridge Tap gently to months remove dirt e Change engine oil Every 500 hours of operation 5 months e Change pump oil Cannot check or change pump oil on the 5525PW NOTE This is a general maintenance schedule Refer to the Engine operation manual for specific information on your engine 18 English TECHNICAL AND CONSUMER INFORMATION Pressure Washers SAE
33. ver for production of muskets The location was logical since waterpower was harnessed from the Husqvarna River to create the water powered plant During the more than 300 years of being the Husqvarna factory has produced a lot of different products from wood stoves to modern kitchen appliances sewing machines bicycles motorcycles etc In 1956 the first motor driven lawn mowers appeared followed by chain saws in 1959 and it is within this area Husqvarna is working today Today Husqvarna is one of the leading manufacturers in the world of forest and garden products with quality as our highest priority The business concept is to develop manufacture and market motor driven products for forestry and gardening as well as for the building and construction industry Husqvarna s aim is also to be in the front edge according to ergonomics usability security and environmental protection That is the reason why we have developed many different features to provide our products within these areas We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to come The purchase of one of our products gives you access to professional help with repairs and service whenever this may be necessary If the retailer who sells your machine is not one of our authorized dealers ask for the address of your nearest service workshop is our wish that you will be satisfied with your pr
Download Pdf Manuals
Related Search