Hunter Fan 45032-01 Fan User Manual
Contents
1. Profile Standard or Angled mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Support Brace Low Profile ad Mounting Style Outlet Box Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high 3 45032 01 11 05 08 Hunter Fan Company A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tool2. of the fan assembly 3 9 Align the screw holes in the washer with the holes in the adapter Assemble securely with three 8 32 x 3 4 screws 3 10 Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy A WARNING Fan may fall if not assembled as directed in these installation instructions Steps 3 8 3 9 Low Profile Washer Step 3 7 Detail Low Profile Washer Adapter Canopy Trim Ring 8 32 x 3 4 Screw Step 3 10 7 45032 01 11 05 08 Hunter Fan Company 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 4 2 4 3 4 4 4 5 4 6 4 7 Before attempting installation make sure the power is still off To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided Connect the bare or green ground wire grounded from the ceiling to the green ground wire grounded from the ceiling plate and the green ground wire from the fan Connect the white wire ungrounded from the ceiling to the white wire ungrounded from the fan Co
3. same side of the metal dowel pin inside the dowrod Loosen the square head setscrew on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the setscrew with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A WARNING Do not carry or lift fan by canopy Raise the fan and place the ball into the hanger bracket 3 5 Align the notch on the ball with the indent in the hanger bracket Rotate the fan until you hear the notch pop into place Go to 4 e Wiring the Fan A WARNING Fan may fall if not assembled as directed in these installation instructions 6 Steps 3 1 3 3 Canopy Trim Ring Setscrew Steps 3 4 3 5 45032 01 11 05 08 e Hunter Fan Company 3 e Assembling and Hanging the Fan Low Profile Only You can assemble your fan for standard or angled mounting as shown in steps 3 1 3 3 on the previous page For low profile mounting ceilings less than 8 feet high see steps 3 6 3 10 on this page 3 6 Remove the screws from the hanger ball bracket 3 7 Place the low profile washer from the parts sack into the canopy 3 8 Place the canopy trim ring and canopy with washer on top
4. For Your Records and Warranty Assistance For reference also attach your receipt or a copy of your receipt to the manual Form 45032 01 20081105 2008 Hunter Fan Co Type 7 Mode IS Owner s Guide and Installation Manual SINCE 1886 Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions Table Of Contents and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock 3 Assembling and Hanging the Fan 6 the circuit breakers in the off position secure
5. To attach the lower switch housing connect the upper plug 7 7 connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch lt ____ Plug Connector housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws Note In compliance with US federal energy regulations this Steps 7 6 7 7 Lower Switch Housing Plug T 6 gs i i Connector ceiling fan contains a device that restricts the light kit to a Detail maximum of 190 Watts Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation Housing 12 45032 01 11 05 08 Hunter Fan Company Assembly Screw 7 Completing Your Installation With or Without a Bowl Light Fixture Continued Installing the Glass Bowl 7 8 7 2 7 10 First install candelabra bulbs 60 Watt Maximum into the sockets If the fandangle is attached to the extra pull chain remove it now Thread the fan pull chain through the hole in the metal disc Th
6. en thread the fan pull chain through the hole in the center of the glass bowl Thread the light pull chain through the hole in the center of the glass bowl Then Thread the light pull chain through the hole in the center of the cover plate Thread the fan pull chain through the grommet hole in the side of the cover plate Place the cover plate up against the glass bowl Align the holes in the cover plate and glass bowl Thread the light pull chain through the finial and screw the finial Light Bulb Reattach the fandangle to the extra pull onto the threaded rod end until tight chain Breakaway Connector Sockets 60 Watt Maximum Metal Disc Metal Rod Glass Bowl in lt gt Cover Plate a Finial S 13 45032 01 11 05 08 Hunter Fan Company gt 7 Completing Your Installation With or Without a Bowl Light Fixture Continued Uninstalling the Light Fixture 7 16 7 17 7 18 7 19 To uninstall the light fixture first disconnect the plug connectors between the black wire and the red wire Disconnect the plug connectors between the two white wires Remove the two screws attaching the light kit to the lower switch housing Remove the light fixture from the lower switch housing pulling Lower Switch disconnected wires through the hole in the center of the lower mousing switch housing Note When removing the wires pull the thin plug connec
7. g 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights dim when turned on or do not turn on 1 Check to make sure the wattage and type of light bulbs installed match the specifications on the light socket If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 16 45032 01 11 05 08 Hunter Fan Company
8. le of the hanger bracket Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other If you are installing the fan on an ANGLED ceiling be sure to orient the hanger bracket as shown in Illustration 2 3 left or right view Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the slotted holes in the hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer Large n 3 Screw ALLA SS y 5 Isolator Hanger Bracket Steps 2 2 2 4 Ceiling Peak Step 2 3 Angled Ceiling Only 45032 01 11 05 08 Hunter Fan Company Ceiling Peak Large 3 Assembling and Hanging the Fan You can assemble your fan for standard or angled mounting as shown in steps 3 1 3 3 For low profile mounting ceilings less than 8 feet high go to steps 3 6 3 9 on the next page 3 1 3 2 3 3 3 4 To assemble fan to hang down from a flat or angled ceiling place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly Feed the wires from the fan through the downrod Note Make sure all the wires are on the
9. ly fasten a prominent 4 Wiring the Fan warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade 7 e Completing Your Installation With or attachment system when installing balancing or cleaning the fan MOU Ea BO EEDE Ee Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 1 Getting Ready 2 Installing the Hanger Bracket 5 Installing the Canopy and Canopy Trim Ring 6 Assembling the Blades 8 Operating and Cleaning Your Ceiling 2008 Hunter Fan Company 2 45032 01 11 05 08 Hunter Fan Company Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a downrod included Angled Mounting recommended for a vaulted or angled ceiling Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low
10. move the canopy trim ring follow these steps 1 Twist canopy trim ring counter clockwise until it releases from canopy Step 5 5 9 Steps 5 1 5 2 Hanger Bracket f Canopy Trim Ring 45032 01 11 05 08 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Use with grommet ews Use without grommet Blade Mounting Screw 10 45032 01 11 05 08 Hunter Fan Company 7 Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button This featu
11. nnect the remaining wires as follows Dual Switch Wiring e The black wire ungrounded from the ceiling to the black wire ungrounded from the fan e The black white wire ungrounded from the fan to the wire ungrounded for the wall switch Single Switch Wiring e The black wire ungrounded from the ceiling to the black ungrounded and the black white wire ungrounded from the fan A CAUTION Be sure no bare wire or wire strands are visible after making connections Turn the wire connectors upward and push them carefully back through the ceiling plate into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box 8 Wire Connector 45032 01 11 05 08 Hunter Fan Company 5 1 5 2 5 3 5 4 5 Installing the Canopy and Canopy Trim Ring Partially install two canopy screws about 2 full turns in the hanger bracket Raise the canopy over the hanger bracket Align partially installed screws with key slots in canopy Twist canopy clockwise to secure Install third amp fourth canopy screw in round hole on canopy Securely tighten all four screws Using both hands push the canopy trim ring up to the top of the canopy Twist canopy trim ring clockwise to secure the canopy Should you need to re
12. pped at the ceiling around the room without causing a draft 8 5 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish 8 6 Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the In cold weather use upward same manner as the fan finish air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing Switch 45032 01 11 05 08 Hunter Fan Company 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade assembly screws and blade iron armature screws until snu
13. re gives you the option of installing the fan with OR without the included light fixture The steps below direct you whether or not you are installing a light fixture A WARNING Use only the light fixture supplied with this fan model 7 1 To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate 7 2 Feed the upper plug connector through the center opening of the housing 7 3 Align the keyhole slots in the housing with the housing assembly screws Steps 7 1 7 3 Housing 7 4 Turn the housing counterclockwise until the housing assembly Assembly Apa screws are firmly situated in the narrow end of the keyhole slots Screw a P Install the remaining screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and light fixture falling 7 5 If you want to install the light fixture proceed with step 7 6 now If you do not want to install the light fixture you need to uninstall it now See Uninstalling the Light Fixture on step 7 15 Once you have uninstalled the light fixture continue with step 7 6 Il 45032 01 11 05 08 Hunter Fan Company 7 Completing Your Installation With or Without a Bowl Light Fixture Continued 7 6
14. s You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 45032 01 11 05 08 Hunter Fan Company 2 2 2 3 2 4 2 Installing the Hanger Bracket Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Note Your fan comes with four pre installed neoprene noise isolators Thread the lead wires from the outlet box down through the hole in the midd
15. tor male through first and then pull the other plug connector female through the hole Install the dummy terminals included in the sack parts on the two disconnected wires in the lower switch housing Install the switch housing cap and plug button to the lower switch housing Once you have uninstalled the light fixture continue with step 7 6 OOOOOOOOOCOOO Male Dummy Terminal Female Dummy Terminal Plug Button __ Step7 21 14 45032 01 11 05 08 Hunter Fan Company 8 Operating and Cleaning Your Ceiling Fan 8 1 Turn on electrical power to the fan 8 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector 8 3 The light pull chain controls the power to the light fixture The In warm weather use chain has two settings ON and OFF downward air flow pattern 8 4 Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air tra
Download Pdf Manuals
Related Search