Hunter Fan 42797-01 Fan User Manual
Contents
1. 5 42797 01 11 13 08 Hunter Fan Company 3 2 3 Assembling the Top Housing To assemble the housing to the hanger adapter align the three raised tabs on the hanger adapter with the three narrow notches in the top housing Make certain the housing sits flat on the adapter Install three 3 assembly screws and tighten them securely 6 Steps 3 1 3 2 Top Housing Assembly Screw 4 Hanger Adapter 42797 01 11 13 08 Hunter Fan Company 4 Assembling and Hanging the Fan Steps 4 1 4 2 lt m Downrod Steps 4 4 4 5 f f Low Profile Washer 42797 01 11 13 08 Hunter Fan Company You can assemble your fan for standard mounting steps 4 1 4 2 or for low profile mounting steps 4 3 4 5 Note For low profile mounting the downrod is replaced with the low profile washer 4 1 To assemble fan to hang down from a flat or angled ceiling insert the downrod through the canopy Feed the wires from the fan through the downrod 4 2 Loosen is fully i normal Skip to A CAUTION The adapter has a special coating on the threads Do move this coating the coating prevents the downrod from not re unscrewing Once assembled do not remove the downrod 4 3 Remove the set screw from the adapter 4 4 Place the low profile washer lip down into the canopy Be sure the green ground wire is pointing2. M odels Owner s Guide and Installation Manual For Your Records and Warranty Assistance e a For reference also attach your receipt or a copy J j a a a of your receipt to the manual SINCE 1886 a Form 42797 01 20081113 2008 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING Table Of Contents INSTALLATION SAVE THESE INSTRUCTIONS 1 Getting Ready e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan 5 Setting the Remote Transmitter and disconnect the power by turning off the circuit breakers to the Receiver outlet box and associated wall switch location If you cannot
3. and associated wall switch location If you cannot lock the circuit breakers e in the off position securely fasten a prominent warning device such as a tag to the service panel peme 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should have a diameter of 9 64 in Step 2 2 l 2 2 Your fan comes with three neoprene noise isolators Isolators Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate 2 3 Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate 2 4 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling T gt 2 5 Place a flat washer on each of the two 3 in wood screws and pass amp l the screws through the slotted holes in the ceiling plate into the Steps 2 3 2 5 pilot holes you drilled Tighten the screws into the 9 64 in pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 in Wood Screw For Angled Ceilings Be sure to orient the ceiling plate so that the hook and Sees N one of the threaded screw holes in the ceiling plate are on the lower side
4. Hunter Fan Company K2 9 1 9 2 Align the keyholes in the light kit fitter with the two partially 9 4 9 5 9 6 9 7 9 8 II 9 Completing Your Installation Partially install two light kit fitter screws into the light kit mounting plate Thread the plug connector from the fan through the light kit fitter installed screws and rotate to engage the screws in the narrow ends of the keyholes Install the remaining screw to secure the light kit fitter to the light kit mounting plate Securely tighten all three screws Connect the 2 pin plug connector from the fan to the 2 pin plug connector from the ballast Attach the ballast to the light kit fitter with two ballast screws Install the included 22 Watt fluorescent bulb into the hooks on the fitter Connect the 4 pin plug from the ballast to the fluorescent bulb Place the glass globe into the globe trim band Align the three holes in the trim band with the three holes in the fitter Install and securely tighten all three screws 13 Steps 9 1 9 8 Fitter Ballast Fluorescent Bulb Glass Globe Globe Trim Band Step 9 9 42797 01 11 13 08 Hunter Fan Company K2 10 Operating the Remote Control and Mounting the Holder Reversing Switch Fan Speed High Fan Speed Low Steps 10 1 10 5 Step 10 6 10 1 The remote transmitter has individual
5. lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 8 Assembling the Blades codes and ANSI NFPA 70 If you are unfamiliar with wiring use a 9 e Completing Your Installation qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a Solid state speed control with this fan Use only Hunter speed controls 2 Installing the Ceiling Plate 3 e Assembling the Top Housing 4 e Assembling and Hanging the Fan 7 6 Wiring the Fan 7 Installing the Canopy 10 e Operating the Remote Control and Mounting the Holder 11 e Operating and Cleaning Your Ceiling 12 Troubleshooting 2008 Hunter Fan Company 2 42797 01 11 13 08 Hunter Fan Company Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angled mounting The steps in this manual include Support Bra
6. replace all the blades 3 Be sure that the glass is secure Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade and or blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 17 42797 01 11 13 08 Hunter Fan Company
7. up toward the ceiling 4 5 Align the holes in the washer with the holes in the adapter Assemble securely with three low profile screws Note Before hanging the fan align and engage the two tabs from the bottom of the canopy and the two grooves in the hanger ball 4 6 Raise the fan and place the hook on the ceiling plate through the round hole in the rim A WARNING Fan may fall if not assembled as directed in these installation instructions the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly nstalled 2 3 threads on the pipe will still be visible this is Securely retighten the set screw with a wrench or pliers Step 4 6 7 a J 5 Setting the Remote Transmitter and Receiver IMPORTANT Before you change the jumper settings make sure the battery is not connected to the transmitter Setting Transmitter and Receiver Codes When two or more fans are located near each other you may desire to have the receiver transmitter for each fan set to a different code so that the operation of one fan does not affect the operation of the other fans Receiver Jumpers The jumpers for the receiver are located on the flat surface of the receiver The jumpers for the transmitter are in the battery compartment The jumpers are very small you can move them most easily using a small pair of pliers or tweezers Example Jumpers Settings Receiver 1
8. Receiver 2 43 2 1 5 1 Change the position of the jumpers in the remote transmitter and the receiver Make sure that the jumpers match in the remote receiver and transmitter If they don t match the transmitter will not function 5 2 Install the included 12 volt battery into the transmitter e Transmitter 1 Transmitter 2 43 2 1 A CAUTION The remote control device complies with part 15 of the FCC rules Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation A WARNING Use only the Hunter Fan speed control supplied with this fan 8 42797 01 11 13 08 Hunter Fan Company K2 Steps 6 5 6 6 Large Wire connector Small Wire connector 42797 01 11 13 08 Hunter Fan Company 6 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 6 1 6 2 6 3 6 4 Disconnect the power by turning off the circuit breakers to the outlet box and associated wa
9. buttons for turning the fan off and on and controlling the light and fan speed 10 2 For best operation start the fan by pressing high then select your desired speed it see 10 3 The reversing switch reverses the direction of the fan edium 10 4 Press the OFF button to turn the fan off Fan Off 10 5 The light button turns the light on to full brightness Push the light button again to turn off the light Fan Light l ee 10 6 You can mount the remote holder to any toggle switch plate with the screws already in the switch plate Or you can simply mount the remote holder on the wall 10 7 This product includes one 12 volt type 23A MN 21 battery for use with the remote control transmitter Please contact your local battery recycling center for proper battery disposal information Step 10 7 14 42797 01 11 13 08 Hunter Fan Company 11 Operating and Cleaning Your Ceiling Fan Restore power at the main electrical panel and turn on the wall switch The light kit should turn ON Note To turn on the light without the remote turn off the wall switch for 5 seconds then back on The light kit will turn on at maximum brightness Press the remote control s HIGH speed button The fan should start and reach its maximum speed Note For everyday operation leave the wall switch ON If the remote control will not be used for 5 days or more turn the wall switch OFF Ceiling fan
10. ce Ceili f j Standard m Box instructions for all three Installer s Choice mounting methods Mounting gt Style Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum Standard Mounting hangs from the performance of your Hunter fan use only Hunter speed controls ceiling by a downrod included For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 in diameter pipe to assure stability and wobble free performance Support Brace A CAUTION To reduce the risk of personal injury attach the fan directly to the Mounting Low Profile _ support structure of oe Outlet Box the building according SY 7 to these instructions and use only the yY a Voo hardware supplied Angled Mounting recommended for a Low Profile Mounting fits close to the vaulted or angled ceiling ceiling recommended for ceilings less than 8 feet high 3 42797 01 11 13 08 Hunter Fan Company l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e L
11. ift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 in bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 42797 01 11 13 08 Hunter Fan Company K2 2 Installing the Ceiling Plate A CAUTION To avoid possible electrical shock before installing your fan Isolator disconnect the power by turning off the circuit breakers to the outlet box
12. iling e Connect the black wire from the receiver to the black wire from the ceiling A CAUTION Be sure no bare wire or wire strands are visible after making connections Run the thin white antenna wire from the receiver through one of the slots in the ceiling plate For best reception make sure the end of the antenna is exposed at the top of the canopy Connect the green ground wires from the ceiling plate and the downrod to the ground wire from the ceiling Push all wires and wire connectors back through the ceiling plate hole into the outlet box Place the green and white wires ona separate side of the outlet box from the other wires 10 42797 01 11 13 08 Hunter Fan Company K2 7 Installing the Canopy 7 1 Holding the canopy raise the fan off the hook 7 2 Align the holes in the canopy with the mounting holes on the ceiling plate 7 3 Insert and tighten the mounting screws securely Steps 7 1 7 3 Mounting Screw lI 42797 01 11 13 08 Hunter Fan Company K2 8 Assembling the Blades WE Motor 8 1 Insert blade into slot Align the holes on the blade with the holes in the fan motor Holes 8 2 Slide flat washers onto the shafts of the blade assembly screws 8 3 Attach the blade to the motor using the blade assembly screws 8 4 Repeat for each blade Step 8 1 Blade Assembly Screw Flat Washer 12 42797 01 11 13 08
13. ll switch location Place the receiver inside the canopy making sure that the dipswitches and the oval shaped holes in the bottom of the receiver are facing down toward the bottom of the canopy Spread Place the receiver in the canopy Make sure the slot in the receiver is aligned with the hook in the ceiling plate place a Using t the receiver lead wires to each side and feed the wires from the top of the fan through the open slot in the receiver To connect the wires hold the bare metal leads together and wire connector over them then twist clockwise until tight he small wire connectors connect the fan to the receiver as follows e Con the Con Con Con Con e Con nect the yellow wire from the fan to the yellow wire from receiver nect the pink wire from the fan to the pink wire from the receiver nect the grey wire from the fan to the grey wire from the receiver nect the red wire from the fan to the red wire from the receiver nect the black wire with a white stripe from the fan to the black wire with a white stripe from the receiver nect the white wire from the fan to the white wire LIGHT OUT from the receiver 9 a J 6 6 6 7 6 8 6 9 6 Wiring the Fan Continued Using the large wire connectors connect the fan and receiver to the power wires as follows e Connect the white wire A C IN from the receiver to the white wire from the ce
14. r and saves up to 10 on heating bills On average at low speed settings Your savings may vary based on climate building type and thermostat setting Save Energy and Money While Protecting the Environment Congratulations You re saving energy and money while protecting the environment by purchasing this ENERGY STAR qualified Hunter ceiling fan With this purchase you are doing your part to protect the environment In 2010 ENERGY STAR qualified ceiling fans are projected to cut air pollution by more than 500 million pounds Your new ceiling fan has earned the ENERGY STAR label because it meets high energy efficiency specifications set by the Environmental Protection Agency EPA ENERGY STAR labeled ceiling fans save energy because they have more efficient fan motors and air delivery due to more aerodynamic blade configurations Ceiling fan models bearing the ENERGY STAR label move air 14 20 more efficiently than typical ceiling fan models For more information on ENERGY STAR visit www energystar gov 16 42797 01 11 13 08 Hunter Fan Company K2 12 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing Problem Noisy operation 1 Tighten the blade screws until snug 2 Check to see if the blade is cracked If so
15. s work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In cold weather having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish 15 42797 01 11 13 08 Hunter Fan Company K2 In warm weather use downward air flow pattern In cold weather use upward air flow pattern Hunter fans have the power to cut your cooling costs up to 40 TT TaD DAD Roe Beat the High Cost of Cooling A The air movement created by a Hunter ceiling fan lets you set your thermostat higher and still stay comfortable Every degree you raise the thermostat saves up to 7 on energy costs So you can cut back on expensive air conditioning and save up to 40 on cooling In winter your Hunter fan recirculates warm ai
Download Pdf Manuals
Related Search