Hunter Fan 42008-01 Fan User Manual
Contents
1. IS Owner s Guide and Installation Manual For reference also attach your receipt or a copy of your receipt to the manual For Your Records and Warranty Assistance 2 VI d lype 2 Mode Where Purchased SINCE 1886 Form 42656 01 20090814 2009 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e Read this entire manual carefully before beginning installation Save these instructions e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied Table of Contents To avoid possible electrical shock before installing your fan 1 Getting Ready disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off positio2. 08 14 09 Hunter Fan Company 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Tighten the blade screws until snug 3 Check to see if the blade is cracked If so replace all the blades 4 Change to an approved speed control 5 Be sure that the glass is secure 6 Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights dim when turned on or do not turn on 1 Check to make sure wattage of light bulbs installed match the specifications on the light socket If you need parts or service assistance please call Problem If the light on this fan shuts off suddenly 888 830 1326 In Canada call 1 866 268 1936 or 1 Turn the power to the fan off
3. Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum Standard Mounting hangs from the performance of your Hunter fan use only Hunter speed controls ceiling by a downrod included For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Mounting Angled Mounting recommended for a vaulted or angled ceiling 3 42656 01 08 14 09 e Hunter Fan Company l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Installing Multiple Fans If you are installing more than Checking Your Fan Parts one f
4. all Note It is recommended you use a magnetic tip screwdriver for the following steps 5 1 Rotate the hanger ball so the tab in the canopy is secure in the hanger ball groove Note Your fan may have multiple tabs and grooves that must be aligned Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate A WARNING The slots in the canopy must remain engaged while swinging the canopy for alignment Holding the canopy up with the screw holes aligned partially install two canopy screws into the holes opposite the ceiling plate tabs Partially install a canopy screw between the slots in the canopy When all the holes are properly aligned securely tighten all three canopy screws Verify that the tabs in the canopy are still in the grooves of the hanger ball Align the tabs on the trim ring opposite the grooves in the hanger ball Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Note Should you need to remove the trim ring press firmly on opposite sides of the trim ring directly above the groove in the hanger ball The tabs will flex out releasing the canopy trim ring 8 42656 01 08 14 09 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Install the grommets into the blades by hand Ste
5. an keep the fan blades and Carefully unpack your fan to avoid damage to the fan parts Refer to blade irons if applicable in sets the included Parts Guide Check for any shipping damage to the motor as they were shipped or fan blades If any parts are missing or damaged contact your Hunter SS dealer or call Hunter Technical Support Department at 888 830 1326 In Canada call 1 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 42656 01 08 14 09 Hunter Fan Company 2 Installing the Ceiling Plate A CAUTION To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 2 1 2 3 2 4 275 2 6 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak Your fan comes with four p
6. at the wall switch Wait 30 visit us at our Web site at seconds then resume power to the fan http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Pkwy 400 Memphis Tennessee 38016 13 42656 01 08 14 09 Hunter Fan Company
7. e sure no bare wire or wire strands are visible after making connections Single Switch Wiring If you want to you can control both fan and light with one switch To do so connect the wires as follows e The bare or green ground wire from the ceiling to the green Fo m Wire Connector Single Switch Wiring AS Ry j 8 _ ground wire from the ceiling plate and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black and the black white Dual Switch Wiring l 8 i N wire from the fan Dual Switch Wiring e The bare or green ground wire from the ceiling to the green ground wire from the pipe ball assembly e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black wire from the fan e The black white wire from the fan to the wire for the wall switch 4 3 Push all wires and wire connectors into the outlet box 7 l Ss 42656 01 08 14 09 Hunter Fan Company 5 Installing the Canopy and Canopy Trim Ring Trim 5 2 5 3 5 4 5 5 Step 5 3 5 6 ki Canopy gt Canopy Canopy Screw A WARNING Failure to complete the following steps could cause the fan to f
8. he set screw with a wrench or pliers Go to 4 e Hanging and Wiring the Fan Trim Ring A WARNING Fan may fall if not assembled as directed in these installation instructions 3 1 Unbundle the wires from the fan For Standard or Angled mounting 3 2 Insert the downrod through the canopy and canopy trim ring Feed the wires from the fan through the downrod on one side of the pin in the ball A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod 6 42656 01 08 14 09 Hunter Fan Company gt 4 Hanging and Wiring the Fan 4 1 Raise the fan and align the slots in the canopy with the hooks on the ceiling plate Note To hang the fan you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 2 Make sure the power to the outlet box and associated wall switch location is still OFF To connect the wires hold the bare metal leads together and place a wire connector over them then twist the wire connector clockwise until tight A CAUTION B
9. ings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector 8 3 Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft In warm weather use downward air flow pattern 8 4 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish 8 5 Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the Same manner as the fan finish In cold weather use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position You will need to remove the light fixture glass to do so Restart fan Reversing Switch 12 42656 01
10. n securely fasten a prominent warning device such as a tag to the service panel 2 Installing the Ceiling Plate 3 e Assembling and Hanging the Fan 4 e Wiring the Fan All wiring must be in accordance with national and local electrical 5 Installing the Canopy and Canopy Trim codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades 7 Completing Your Installation With a Light Fixture To reduce the risk of fire electrical shock or motor damage do not use a Solid state speed control with this fan Use only Hunter speed controls 8 Operating and Cleaning Your Ceiling Fan 9 Troubleshooting 2009 Hunter Fan Company 2 42656 01 08 14 09 e Hunter Fan Company Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angled mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Support Brace Ceiling Standard Outlet Box Mounting gt Style
11. p 6 1 Detail 6 2 Place each blade between a blade iron and medallion Install three blade screws to attach the medallion to the blade iron Repeat for all blades 6 3 Remove the blade iron mounting screws and plastic shipping bumpers from the motor Note Some blade iron mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade iron mounting screw through the blade iron and attach lightly to the fan Insert the second blade iron mounting screw then securely tighten both screws Blade Assembly Use with grommet ews Use without grommet Blade Iron Mounting Screw 42656 01 08 14 09 Hunter Fan Company Steps 6 2 6 4 Housing Assembly Screw 7 Installing the Light Fixture 7 1 Partially install two housing assembly screws into the housing Housing Step 7 1 7 2 To attach the light fixture connect the upper plug connector from the motor to the lower plug connector in the light fixture assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product 7 3 Place the keyholes in the light fixture assembly over the partially installed screws in the housing 7 4 Rotate the light fixture clockwise until the screws are firmly situated in the nar
12. reinstalled noise isolators Check to make sure all four isolators are in place and were not removed during shipment Place a flat washer on each of the two 3 wood screws Thread the supply wires from the outlet box in the ceiling through the hole in the center of the ceiling plate Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling Pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Screw EEE tn 5 42656 01 08 14 09 Hunter Fan Company Toward Ceiling Peak For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak Ceiling Plate x lt gt Steps 2 3 2 6 Standard or Angled Mounting 3 Assembling the Fan Steps 3 2 3 3 Set Screw 9 Downrod lt Canopy 3 3 Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is I lt Canopy normal Securely retighten t
13. row end of the keyholes Install the remaining screw Tighten all three screws securely Light Kit Steps 7 2 7 4 Housing Assembly Screw 7 5 Install three candelabra bulbs 40 Watt maximum each lt gt lt _ lt _ Candelabra Bulb Step 7 5 Note In compliance with US federal energy regulations this ceiling fan contains a device that restricts the light kit toa maximum of 190 Watts Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation 42656 01 08 14 09 e Hunter Fan Company 7 Installing the Light Fixture continued 7 6 Remove the breakaway connectors from the light and fan pull chains and thread them both through the hole in the center of the glass bowl 7 7 Place the cover plate up against the glass bowl Align the holes in the cover plate and glass bowl 7 8 Thread the fan pull chain and light pull chain through the appropriate holes 7 9 Screw the finial onto the threaded rod end until tight 11 il Glass Bowl q lt Cap lt finial Step 7 6 7 11 42656 01 08 14 09 Hunter Fan Company 8 Operating and Cleaning Your Ceiling Fan 8 1 Turn on electrical power to the fan 8 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change sett
Download Pdf Manuals
Related Search