Hunter Fan 41923 Fan User Manual
Contents
1. installation and Operation manual for Hunter For Your Records and Warranty Assistance asec Ceiling Fans Catalog Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual 41923 01 11 21 05 Welcome Table of Contents 1 e Getting Ready 2 Installing the Ceiling Plate 3 Assembling and Hanging the Fan 4 e Setting the Remote Transmitter and Reciever 5 e Wiring the Fan 6 Installing the Canopy and Canopy Trim Ring 7 Assembling the Blades 8 Installing the Switch Housing 9 e Operating the Remote Control and Mounting the Holder 10 e Operating and Cleaning Your Ceiling Fan 11 Troubleshooting 2005 Hunter Fan Company Hunter Fan Company Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e Read this entire manual carefully before beginning installation Sa2. Note When iii the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the set screw with the allen wrench Skip to Step 3 6 m lt Allen Head Set Screw A CAUTION The adapter has a special coating on the threads Do Steps 3 4 3 5 not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod 3 3 Remove the set screw from the adapter 3 4 To assemble the fan to hang from a low ceiling place the low profile washer lip up into the canopy Be sure the green ground wire is pointing up toward the ceiling 3 5 Align the holes in the washer with the holes in the adapter Assemble securely with three 8 32 x 3 4 screws 3 6 Raise the fan and place the hook on the ceiling plate through the U shaped hole in the rim A WARNING Fan may fall if not assembled as directed in these installation instructions 8 32 x 3 4 Screw Hunter Fan Company 41923 01 11 21 05 4 Setting the Remote Transmitter and Receiver You must now set the jumpers in the remote transmitter and receiver so that they match 4 1 Change the position of the jumpers in the transmitter and the receiver Be sure the position of the jumper in the transmitter matches the position of the jumper in the receiver If they don t match the controller will not function For instructions on how
3. instructions for all three Installer s Choice mounting methods Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls 12 Standard Mounting hangs from For ceilings higher than 8 feet you the ceiling by a downrod included recommended for ceilings 8 feet or higher can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Angle Mounting recommended for a vaulted or angled ceiling 41923 01 11 21 05 Hunter Fan Company 3 l Getting Ready Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped Hunter Fan Company To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering
4. 5 Small Wire Nut 5 6 5 7 Hunter Fan Company 5 1 5 2 Steps 5 3 5 7 5 4 codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Make sure the power is still off To connect the wires hold the bare metal leads together and place a wire nut over them then twist clockwise until tight For all these connections use the wire nuts provided A CAUTION Be sure no bare wire or wire strands are visible after making connections Connect the ground wire from the ceiling to the green ground wire from the ceiling plate and the green ground wire from the downrod or low profile washer Using the large wire nuts connect the white wire and the black wire from the ceiling as follows e The white common power wire from the ceiling to the white wire from the receiver marked on red tag NEUTRAL IN e The black power wire from the ceiling to the black wire from the receiver marked on red tag LIVE IN Using the small wire nuts connect the wires from the fan as follows e The black white wire from the fan to the red wire from the receiver marked on white tag LIGHT OUT e The black wire from the fan to the black wire from the receiver marked on white tag FAN OUT e The white wire from the fan to the white wire from the receiver marked on white tag COMMON OUT Check each connection to make sure no bare wire or wire strands are visible Push all wires and wi
5. best operation start the fan by pressing high then select your desired speed The light button turns the light on to full brightness To dim the light hold the light button down until you reach your desired brightness Push the light button again to turn off the light Press the OFF button to turn the fan off When necessary replace the battery with a 12 volt type 23A MN 21 battery or equivalent You can mount the remote holder to any toggle switch plate with the screws already in the switch plate Or you can simply mount the remote holder on the wall Step 9 6 41923 01 11 21 05 10 Operating and Cleaning Your Ceiling Fan 10 1 Turn on electrical power to the fan 10 2 Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In cold weather having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft 10 3 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may In warm weather use use an artistic agent but never abrasive cleaning agents as they downward air flow pattern will damage the finish 10 4 Clean wood finish blades with a furnitu
6. ed balancing kit and instructions to balance the fan 2 Tighten all blade and or blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 Hunter Fan Company 41923 01 11 21 05
7. embly screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing Steps 8 1 8 4 fixture falling Housing Assembly P Screw WItC To attach the lower switch housing connect the upper plug Boe connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws Steps 8 5 8 6 Lower Switch Housing OLSIN Assembly Screw 41923 01 11 21 05 Hunter Fan Company 9 Operating the Remote Control and Mounting the Holder Fan Speed High Fan Speed Low 12 Steps 9 1 9 4 Step 9 5 Hunter Fan Company Fan Speed Medium Fan Off Fan Light 9 1 9 2 9 4 9 5 9 6 The remote transmitter has individual buttons for turning the fan off and on and controlling the light and fan speed For
8. il 7 1 Your fan may include blade grommets If your fan has grommets insert them by hand into the holes on the blades 7 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 7 3 Some blade mounting screws are installed in the motor to secure shipping blocks Remove the blade mountings screws and rubber bumpers from the motor Save the screws and discard the bumpers 7 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade Blade Assembl l g mounting screw then securely tighten both mounting screws Screws Use with grommet Steps 7 1 7 2 10 Use without grommet Blade Mounting Screw Hunter Fan Company 41923 01 11 21 05 8 1 8 2 8 4 8 5 8 6 Note You can customize your Hunter fan with a number of accessory light kits Align the keyhole slots in the housing with the housing assembly 8 Installing the Switch Housing To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate Feed the upper plug connector through the center opening of the housing SCrews Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining housing ass
9. re nuts back through the ceiling plate hole into the outlet box Run the white antenna wire from the receiver through one of the slots in the ceiling plate so that it rests between the ceiling plate and the ceiling Push it to the edge of the ceiling plate for clear reception 41923 01 11 21 05 6 4 6 Installing the Canopy and Canopy Trim Ring Holding the canopy raise the fan off the hook 6 2 6 3 Align the slots in the canopy with the tabs on the ceiling plate Raise the canopy over the ceiling plate Rotate the canopy clockwise until the tabs on the ceiling plate totally engage with the slots in the canopy Loosely assemble the three canopy screws into the canopy one at a time Once all three screws are in tighten them Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Should you need to remove the canopy trim ring follow these steps 1 Locate the tab indicators small bumps on top of tabs 2 Press firmly on opposite sides of the ring towards the canopy The tabs will flex out releasing the trim ring from the canopy 41923 01 e 11 21 05 Step 6 2 gt Ceiling Plate gt Canopy Trim J Ring Steps 6 4 6 5 Hunter Fan Company 7 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan Step 7 1 Deta
10. re polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish In cold weather use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the Opposite position Restart fan Reversing Switch 41923 01 11 21 05 Hunter Fan Company 13 11 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Remove the shipping bumpers 6 If the transmitter LED light does not come on replace the battery with a new 12 volt alkaline battery If the LED light does come on but the fan will not work check the settings in the receiver and transmitter Refer to 4e Setting the Remote Transmitter and Receiver 7 for more information Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Tighten the blade screws until snug 14 3 Check to see if the blade is cracked If so replace all the blades 4 Be sure that the glass is secure Problem Excessive wobbling 1 If your fan wobbles when operating use the enclos
11. the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 41923 01 11 21 05 2 2 2 4 2 5 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Your fan comes with four neoprene noise isolators Isolators Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate Align the slotted holes in the ceiling plate with
12. the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Screw eens FUVUNKUNUEEOUNUUUY He 41923 01 11 21 05 2 Installing the Ceiling Plate Isolator gt A Ceiling Plate P a A Rig Steps 2 3 2 5 a _ For Angled Ceilings Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing towards the ceiling peak Hunter Fan Company 3 Assembling and Hanging the Fan Steps 3 1 3 2 You can assemble your fan for standard mounting steps 3 1 3 2 or for low profile mounting steps 3 3 3 5 Note For low profile lt Downrod mounting the downrod is replaced with the low profile washer 3 1 To assemble fan to hang down from a flat or angled ceiling insert the downrod through the canopy and canopy trim ring Feed the lt C A wires from the fan through the downrod 3 2 Using the provided allen wrench loosen the allen head set screw Canopy on the adapter to install the pipe and ball assembly
13. to set the jumpers read the box below 4 2 Install the included 12 volt battery into the transmitter Setting Jumpers When two or more fans are located near each other you may desire to have the receiver transmitter for each fan set to a different code so that the operation of one fan does not affect the operation of the other fans In the transmitter you can access the jumpers from the battery compartment The jumpers are very small You can move them most easily using a small pair of pliers or tweezers IMPORTANT Before you change a jumper make sure the battery is not connected to the transmitter A CAUTION The remote control device complies with part 15 of the FCC rules Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Note Use with a fan that incorporates an air gap switch normal on off wall switch A WARNING Maximum fan load is 1 Amp maximum lamp is 100 Watts Do not use any speed control with this product 41923 01 11 21 05 Example Jumpers Settings Transmitter 2 Hunter Fan Company 5e Wiring the Fan Receiver All wiring must be in accordance with national and local electrical Large Wire Nut 5
14. ve these instructions e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 41923 01 11 21 05 Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one 10 of three ways depending on ceiling height and your preference Low Profile Standard or Angle mounting The steps in this manual include
Download Pdf Manuals
Related Search