Humminbird 409000-1 Fish Finder User Manual
Contents
1. Flush Mount Temp Speed Gauge Thank You Thank you for choosing Humminbird America s 1 name in fishfinders Humminbird has built its reputation by designing and manufacturing top quality thoroughly reliable marine equipment Genuine Humminbird accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird product Your Humminbird is designed for trouble free use in even the harshest marine environment In the unlikely event that your Humminbird does require repairs we offer an exclusive Service Policy free of charge during the first year after purchase and available at a reasonable rate after the one year period For complete details see the Warranty section included in this manual Contact our Customer Resource Center at either 1 800 633 1468 or visit our website at www humminbird com Installation Overview Following are instructions for the installation of this accessory Before you start installation we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird accessory If you find that any items are missing from your installation kit call our Customer Resource Center at 1 800 633 1468 or visit our website at www humminbird com NOTE This accessory requires drilling a hole in the hull of the boat therefore installation should be performed by a qualified marine technician In addition to the hardware supplied with your accessory you will n2. Gauge 1 From the outside of the hull drill a small pilot hole smaller than the centering bit of your drill bit or hole saw at the mounting location you selected in procedure 2 2 Use the pilot hole from the outside of the hull to drill a 2 hole 3 Thoroughly clean and deburr the drilled hole and clean the outside of the hull 4 Disassemble the temp speed gauge and wing nut from the threaded housing 930501 1_B Thru Hull Installation Areas of Possible Turbulence Rivets Transom Strakes Hull Stepped Hull 2008 Humminbird Eufaula AL USA All rights reserved 10 Flush Mount Temp Speed Gauge Apply a generous amount of marine grade silicone sealant inside the drilled hole and along the mating surfaces of the threaded housing Insert the threaded housing through the drilled hole with the clevis pin holes oriented with the length of the boat Slide the wing nut over the threaded housing then Hand Tighten the wing nut ONLY until the assembly is firmly seated then tighten NO MORE than 1 8 of an additional turn Make sure that the orientation of the clevis pin holes have not changed CAUTION To avoid damage do not overtighten the wing nut If the hull is wood it will swell when wet NOTE Remove the excess marine grade silicone sealant from the outside of the hull to ensure smooth water flow over the temp speed gauge Allow the sealant to dry according to the sealant manufacturer s recommend
3. ailed because of an accident or abnormal operation e Repaired or modified by entities other than Humminbird Please retain your original receipt as a proof of the purchase date This will be required for in warranty service THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE THE CUSTOMER S EXCLUSIVE REMEDY EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE IN NO EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS Some states do not allow limitations on an implied warranty or the exclusion of incidental or consequential damages so the above exclusions may not apply to you You may also have other rights which vary from state to state 3 930501 1_B Humminbird Service Policy Even though you ll probably never need to take advantage of our incredible service policy it s good to know that we back our products this confidently We do it because you deserve the best We will make every effort to repair your unit within three business days from the receipt of your unit at our factory This does not include shipping time to and from our factory Units received on Friday are typically shipped by the following Wednesday units received Monday are typically shipped by Thursd
4. ation before using your boat Then check for leaks over the next 24 hours and re install the temp speed gauge if necessary Slide two of the O Rings over the gauge body and seat them into each groove Lubricate the O Rings and the inside of the threaded housing Orient the gauge so that the arrow on the flange points forward and slide the gauge fully into the threaded housing Insert the clevis pin through the holes in the threaded housing and gauge Insert the ring clip through the hole on the clevis pin Loop the chain around the cable coming from the gauge and secure each end into the slots on the wing nut Routing the Cable The temp speed gauge cable must be routed to the point where the control head is mounted 1 NOTE Your boat may have a pre existing wiring channel or conduit that you can use for the cable CAUTION Do not cut or shorten the cable and try not to damage the cable insulation Route the cable as far as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference If the cable is too short extension cables are available to extend the cable up to a total of 50 For assistance contact the Customer Resource Center at www humminbird com or call 1 800 633 1468 for more information Route and secure the cable avoiding areas where it may be damaged or interfere with normal boating operations Connecting the Cable Insert the temp speed gauge cable into the appropriate t
5. ay etc All repair work is performed by factory trained technicians to meet exacting factory specifications Factory serviced units go through the same rigorous testing and quality control inspections as new production units After the original warranty period a standard flat rate service charge will be assessed for each repair physical damage and missing parts are not included Any repairs made after the original warranty will be warranted for an additional 90 days after service has been performed by our factory technicians You can contact our Customer Resource Center or visit our website to verify the flat rate repair fee for your product visit the Product Support section http www humminbird com We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain This Service Policy is valid in the United States only This applies only to Humminbird products returned to our factory in Eufaula Alabama This Service Policy is subject to change without notice 2008 Humminbird Eufaula AL USA All rights reserved Flush Mount Temp Speed Gauge Returning Your Unit for Service Before sending your unit in for repair please contact the factory either by phone or by email to obtain a Repair Authorization Number for your unit Please have your product model name and serial number available before calling the factory If you contact the factory by e mail please
6. ce the effectiveness of the Temp Speed Accessory Periodically clean the face of the Temp Speed Accessory with hot water ap If your boat remains out of the water for a long period of time it may take some time to wet the Temp Speed Accessory after it is returned to the water Small air bubbles can cling to the surface of the gauge and interfere with proper operation These bubbles will dissipate with time or you may wipe the face of the Temp Speed Accessory with your fingers after the gauge is in the water 1 Year Limited Warranty We warrant the original retail purchaser that products made by Humminbird have been manufactured free from defects in materials and workmanship This warranty is effective for one year from the date of original retail purchase Humminbird products found to be defective and covered by this warranty will be replaced or repaired free of charge at Humminbird option and returned to the customer freight prepaid Humminbird sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird Humminbird is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts This warranty does not apply to a product that has been e mproperly installed e Used in an installation other than that recommended in the product installation and operation instructions e Damaged or has f
7. eed a drill a small drill bit for a pilot hole a 2 hole saw a level and marine grade silicone sealant Installation Perform the procedures in the following sections to install the Temp Speed Gauge on your boat Testing the Temp Speed Gauge Prior to Installation Prior to installation test the Temp Speed Gauge to make sure that no damage occurred during shipping After connecting the temp speed gauge to the control head hold the gauge in the water over the side of the boat to confirm proper operation If the gauge is working properly the control head will begin displaying water temperature immediately Locating the Temp Speed Gauge Mounting Position You must first determine the best location on the transom to install the Temp Speed Gauge It is very important to locate the gauge in an area that is relatively free of turbulent water constantly submerged and positioned to allow you to trailer the boat without damaging the gauge The best location will be aft midship as close to the centerline of the boat as possible The gauge should be mounted forward of the prop s on inboard boats and separate from other transducers strakes rivets ribs or other protrusions Inside the boat there must be room to access the mounting location for installation and cable routing Notice that the Temp Speed Gauge is removable from the threaded housing adequate overhead space must be available to remove this insert Attaching the Temp Speed
8. erminal slot The cable connectors are labeled and there are corresponding labels on the cable holder on the rear of the control head The slots are keyed to prevent reversed installation so be careful not to force the connector into the holder Your Temp Speed Gauge is now ready for operation Removing the Temp Speed Gauge Use the steps below to remove the Temp Speed Gauge from your boat 1 2 3 Carefully disconnect the temp speed gauge cable from the control head Disassemble the temp speed gauge and wing nut from the threaded housing Slide two of the O Rings over the plug included and seat them into each groove of the plug body Lubricate the 0 Rings and the inside of the threaded housing Orient the plug so that the arrow on the flange points forward and slide the plug fully into the threaded housing Insert the clevis pin through the holes in the threaded housing and plug Insert the ring clip through the hole in the clevis pin For assistance contact the Customer Resource Center at www humminbird com or call 1 800 633 1468 for more information 2 930501 1_B Assembling the Gauge Wing Nut lt Hull cut away view wre A Clevis Pin Holes Threaded lt Housing i Front of Boat Clevis Pin 2008 Humminbird Eufaula AL USA All rights reserved Flush Mount Temp Speed Gauge Maintenance If your boat remains in the water for long periods of time algae and other marin growth can redu
9. include your product model name and serial number in the e mail and use Request for Repair Authorization Number for your e mail subject header You should include your Repair Authorization Number in all subsequent communications about your unit For IN WARRANTY service complete the following steps e Obtain a Repair Authorization Number from the Humminbird Customer Resource Center Tag product with your name street address phone number and your assigned Repair Authorization Number Include a brief written description of the problem Include a copy of your receipt to show proof and date of purchase Return product freight prepaid to Humminbird using an insured carrier with delivery confirmation For OUT OF WARRANTY service complete the following steps e Obtain a Repair Authorization Number from the Humminbird Customer Resource Center Include payment in the form of credit card number and expiration date money order or personal check Please do not send cash Tag product with your name street address phone number and your assigned Repair Authorization Number Include a brief written description of the problem Return product freight prepaid to Humminbird using an insured carrier with delivery confirmation 4 930501 1_B Contact Humminbird Contact the Humminbird Customer Resource Center in any of the following ways By Telephone Monday Friday 8 00 a m to 4 30 p m Central Standard Ti
10. me 1 800 633 1468 By e mail typically we respond to your e mail within three business days cservice johnsonoutdoors com For direct shipping our address is Humminbird Service Department 678 Humminbird Lane Eufaula AL 36027 USA WARNING Disassembly and repair of this electronic unit should only be performed by authorized service personnel Any modification of the serial number or attempt to repair the original equipment or accessories by unauthorized individuals will void the warranty 2008 Humminbird Eufaula AL USA All rights reserved
Download Pdf Manuals
Related Search