Hoshizaki AM-50BAE-ADDS Ice Maker User Manual
Contents
1. Top Panel Ice Making gt E Mechanism 9 a An Bin Control Thermostat Bulb Scoop Holder T echt Slope n m GI Magnet Catch Front Panel Control Switch mr d n J O O ABS amp U amp P u 1 E S a R e oor Power Cord lt Louver B Electrical Data HOSHIZAKI ICE MAKER MODEL NUMBER ERIAL NUMBER C SUPPLY VOLTAGE 115 120 60 1 MPERES 3 4 AMPS ESIGN PRESSURE HI 240PSI LO 120PSI EFRIGERANT 134a 4 2 OZ AM 50BAE MOTOR COMPRESSOR THERMALLY PROTECTED APPROVED FOR OUTDOOR USE Hoshizaki America Inc Peachtree City GA www hoshizaki com For certification marks see the nameplate in the storage bin Note Only the MODEL NUMBER is replaced for AM 50BAE DS AM 50BAE AD and AM 50BAE ADDS The nameplate provides electrical and refrigerant data The nameplate is located in the storage bin We reserve the right to make changes in specifications and design without prior notice C Dimensions Connections 1 AM 50BAE AIR IN gt AIR OUT de 30 1 2 WI mm JH2. 6 Fasten the sheet metal bracket to the bottom of the door with the three T2 screws provided Tighten the screws to the door See Fig 25 Door Snug the screws but do not tighten Overlay Panel Sheet Metal Bracket a a Fig 24 Fig 25 21 7 Tighten the four M4x25 pan head screws installed in step 5 See Fig 26 8 Replace the door gasket in its proper orientation Reinsert the bushings into hinge C1 and hinge C2 the hinges attached to the door See Fig 27 Bushing A u Tighten the screws g B Bushing Fig 26 Fig 27 9 Attach the door to hinge A then continue to maintain a hold on the door Screw the hinge stop pin into hinge B until it is tight See Fig 28 10 Insert the 2 canoe clips included in the accessory bag into the holes on top of the door See Fig 29 Canoe Clips Door Hinge Stop Pin Fig 28 Fig 29 22 D Setup 1 Position the icemaker in the selected permanent location 2 Level the icemaker from
3. 2 inch 5 cm air gap Minimum 1 2 Nominal ID Hard Pipe G Final Checklist A WARNING CHOKING HAZARD Ensure all components fasteners and thumbscrews are securely in place after installation Make sure that none have fallen into the storage bin 1 Is the icemaker level 2 Is the icemaker in a site where the ambient temperature is within 45 F to 100 F 7 C to 38 C and the water temperature within 45 F to 95 F 7 C to 35 C all year around 3 Have the shipping carton tape and packing material been removed from the icemaker 4 Have all electrical and water connections been made Do electrical and water connections meet all national state and local code and regulation requirements 5 Has the power supply voltage been checked or tested against the nameplate rating Is the power supply a properly grounded independent 3 prong wall outlet 6 Are the water supply line shut off valve and drain valve installed Has the water supply pressure been checked to ensure a minimum of 10 PSIG and a maximum of 113 PSIG 7 Are all components fasteners and thumbscrews securely in place 8 Has the end user been given this instruction manual and instructed on how to operate the icemaker and the importance of the recommended periodic maintenance 9 Has the end user been given the name and telephone number of an authorized service agent 10 Has the warranty tag been filled out and
4. m HOLIMS 1081NO2 LSI ERA 00r LOI lt n lt e ane cll i 1 21 21 8 LE 0 0 j e H 171 d 82 wol 0 8 E rm wlio noL 13NVd 3000 Ts lS 8 71 e 91 m T 16 41 lu m 81 e S GE L p 100 HIV amp 100 uiv H an HIN L ni 8 61 S1 706 LE gt 86 gt 96 9 22 7 SLS 86 4 AM 50BAE ADDS JQISLNO 9NOT uc 4000 QNIH38 HILIMS TOYLNOD ldd 131100 NIVUG dd e 1 137N1 H31VM ui ww 08002 AlddNS 80104 L I8 1 ri SZ 007 LOI ENN ans 1 Lu Gi 21 0 8 N 9 0 0 N 171 E 82 cs 0 e oo S 3NVd 8000 2 C 7 2 T co 09 ue ca pe E gt 100 HI de 100 UV i Xe UD aly P 8 61 S 1 sun 706 9 9 96 9 22 7 SLS 86 10 ll Installation and Operating Instructions A WARNING 1 This icemaker must be installed in accordance with applicable national state and local codes and regulations 2 CHOKING HAZARD Ensure all components fasteners and thumbscrews are securely in place after installation Make sure that none have fallen into the storage bin A Checks Before Ins
5. Clean the storage bin liner door liner and door gasket using a neutral cleaner Rinse thoroughly after cleaning 9 Move the control switch to the ICE position to start the automatic icemaking process 10 To confirm bin control operation hold ice in contact with the bin control thermostat bulb The icemaker should stop within 10 seconds Adjustment may be needed particularly at higher altitude locations 26 Ill Cleaning and Maintenance A WARNING 1 CHOKING HAZARD Ensure all components fasteners and thumbscrews are securely in place after any cleaning or maintenance is done to the unit Make sure that none have fallen into the storage bin 2 The storage bin is for ice use only Do not store anything else in the storage bin 3 Keep the area around the icemaker clean Dirt dust or insects in the unit could cause electrical damage to the equipment or harm to individuals A Cleaning and Sanitizing Instructions Hoshizaki recommends cleaning and sanitizing this unit at least once a year More frequent cleaning and sanitizing however may be required in some existing water conditions A WARNING 1 To prevent injury to individuals and damage to the icemaker do not use ammonia type cleaners 2 Carefully follow any instructions provided with the bottles of cleaning and sanitizing solution 3 Always wear liquid proof gloves and goggles to prevent the cleaning and sanitizing solutions from coming into contact wit
6. eee eee 27 1 Cleaning SOolullon EE 27 2 Cleaning Procedure sss sees sees eee 27 3 Sanitizing Solutions sese neee 29 4 Bantiizing Hee sss sees eee 29 B Maintenance eee 32 C Preparing the Icemaker for Long Storage en 33 Important Safety Information Throughout this manual notices appear to bring your attention to situations which could result in death serious injury or damage to the unit A WARNING Indicates a hazardous situation which could result in death or serious injury CAUTION Indicates a situation which could result in damage to the unit IMPORTANT Indicates important information about the use and care of the unit A WARNING This icemaker should be destined only to the use for which it has been expressly conceived Any other use should be considered improper and therefore dangerous The manufacturer cannot be held responsible for injury or damage resulting from improper incorrect and unreasonable use To reduce the risk of death electric shock serious injury or fire follow basic precautions including the following This unit requires an independent power supply See the nameplate for proper voltage and breaker fuse size Failure to use a proper breaker or fuse can result in a tripped breaker blown fuse or damage to existing wiring This could lead to heat generation or fire THIS UNIT MUST BE GROUNDED This unit is equipped with a 3 prong grounding plug to reduce the ri
7. pipe See Fig 38 D LEN Wel EW Tab Front Frame Pipe Rear Frame Pipe _ Ice Chute Tab l Water Tank Fig 37 Fig 38 29 7 Disconnect the discharge tube from the spray assembly then slide out the spray assembly See Fig 39 8 Remove the two caps See Fig 40 Discharge Tube Spray Assembly Fig 39 Fig 40 9 Soak all of the removed parts and the scoop in the sanitizing solution for 10 minutes If the spray assembly nozzles are clogged clean them with a wire or a suitable brush 10 Rinse the parts thoroughly with clean water 11 Refit the 2 caps in their correct positions Make sure the reducing pipe is in place in the center See Fig 41 12 Slide in the spray assembly along the rails on the left and right brackets See Fig 42 Connect the discharge tube securely to the spray assembly a loose fitting may cause a water leak Reducing Pipe Left Bracket Right Bracket RISA Discharge Tube Fig 41 S 13 Position and lock the ice chute onto the front and rear frame pipes by pushing the ice chute down until it clicks onto both frame pipes See Fig 43 Fig 42 14 Slide in the water tank along the rails at the bottom of the left and right brackets until it locks into place See Fig 44 Left Bracket Right Bracket A n Rear Frame _ Pipe Front Frame Pipe Water Tank Fig 44 30 15 Reconnect the suction tube 16 Ho
8. remove the door from hinge A See Fig 1 Hinge B Hinge A Hinge Stop Pin Fig 1 2 Remove the 2 screws securing the top panel then lift it off See Fig 2 Top Panel Screws Fig 2 3 Remove hinge A and the bracket from the right side of the unit and the top brace from the left side Rotate hinge A to position the gasket notch to the inside then fasten hinge A and the bracket to the left side and the top brace to the right side See Fig 3 Bracket SEN Hinge A t 472 i d eeng Fig 3 Top Brace d Gasket Notch Gk 4 Remove hinge B from the right side of the unit and the 2 filler screws from the left side Attach the 2 filler screws to the right side and attach hinge B to the left side See Fig 4 5 Rotate the top panel 180 from its previous position This brings the notch that was previously in the right rear to the left front See Fig 5 Hook the rear part of the panel on the body then secure the front with the 2 screws removed in step 2 Screws lt gt Hinge B N SS Filler S Screws Fig 4 6 Remove the 2 screws attaching the door handle and also remove the other 2 screws indicated in the illustration Use 2 of the screws to attach the handle to the other side of the door and attach the other 2
9. was previously in the right rear to the left front See Fig 14 Hook the rear part of the panel on the body then secure the front with the 2 screws removed in step 6a Screws lt Top Panel Notch Hinge B NER Das Filler Z SS Screws Gasket Notch 4 Hinge A Right Not Needed Fig 13 Fig 14 f Remove hinge C1 from the top right part of the door flip it and reattach to the bottom left Remove hinge C2 from the bottom right part of the door flip it and reattach to the top left See Fig 15 Proceed to step 7 Screws 1 Hinge C2 Fig 15 Hinge C1 Screws 7 Remove the bushings from hinge C1 and hinge C2 the hinges attached to the door See Fig 16 8 Remove the gasket from the door See Fig 17 Bushing Gasket nl gt Fig 16 9 Temporarily fasten the overlay panel to the door using 2 of the M4x25 pan head screws provided See Fig 18 CAUTION Ensure that the back surface of overlay panel is flat before attaching 10 Mark the centerpoint of the hinge C1 and hinge C2 holes that extend over the overlay panel See Fig 19 IS 3 mM Hinge Mark the center point Overlay Panel Fig 18 Fig 19 11 Remove the over
10. 2a za OL T u E 2 E 8 01 E 12 e o ECH r gt UH x qe E 6 5 L ST em Hy E S a ce x SS oe gt 02 1 ao ola gt ecole Wo SH CO E Q nu 3 LS QV 2 0 0 lt 4 _ _ p Se S S E 5 UE 32 elg S az J SR sa 6 SE Sle 35 X s d gt 061 soles L 9 OLI S Nu CONTROL SWITCH BEHIND DOOR 2 AM 50BAE DS TISINO SNOT We G40 ATddNS Y3MOd pet Een 0 0 s Ch coc wo Idd 2 1 E 131100 NIVYG 271 rg Id 221 137N Y3L1VM re C 7 gt 3 t z EN 09 woo ur ww syun 0000 QNIH38 u HOLIMS 1041NO2 8 61 2v 007 LOI Sl S 1 ie ENN 8 R 9 0 171 82 ws Co B m TINVd 4000 CS e 8 91 o9 S 6 OSL 4m 100 uv gt 100 YIV lt NI HIN 3 AM 50BAE AD 301S1NO ONO We YO AlddNS uiMOd Le bel 0 UY S Idd 2 1 c 131100 NIVUG 08 21 781 dd eer _ 13INI YJLYM AEN lo 09 Klee ur ww syun 8000 QNIH38
11. Hoshizaki America Inc Self Contained Cuber Models AM 50BAE AM 50BAE DS AM 50BAE AD AM 50BAE ADDS INSTRUCTION MANUAL A Superior Degree of Reliability www hoshizaki com Issued 3 10 2006 Revised 7 1 201 IMPORTANT Only qualified service technicians should install service or maintain the icemaker No installation service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual Likewise the owner manager should not proceed to operate the icemaker until the installer has instructed them on its proper operation Failure to install operate and maintain the equipment in accordance with this manual may adversely affect safety performance component life and warranty coverage Hoshizaki provides this manual primarily to assist qualified service technicians in the installation maintenance and service of the icemaker Should the reader have any questions or concerns which have not been satisfactorily addressed please call write or send an e mail message to the Hoshizaki Technical Support Department for assistance HOSHIZAKI AMERICA INC 618 Highway 74 South Peachtree City GA 30269 Attn Hoshizaki Technical Support Department Phone 1 800 233 1940 Technical Support 770 487 2331 Fax 1 800 843 1056 770 487 3360 E mail techsupport hoshizaki com Web Site www hoshizaki com NOTE To expedite assistance all correspondence communication
12. MUST include the following information s Model Number e Serial Number Complete and detailed explanation of the problem IMPORTANT This manual should be read carefully before the icemaker is installed and operated Only qualified service technicians should install service and maintain the icemaker Read the warnings contained in this booklet carefully as they give important information regarding safety Please retain this booklet for any further reference that may be necessary CONTENTS Important Safety Information enna 4 Ee EE 5 POM Te EE 5 B Electnical Data EEN 6 C Dimensions ConnectiONS enna 7 1 AM 50BAE 7 SEENEN 8 3 AM 50BAE AD eee 9 4 EE 10 Il Installation and Operating Instructions mmm 11 A Checks Before Installation u nannte 11 ME EE 11 LEE 0 EE 11 2 Built In Installation Ste eee eee eee 12 KEE eege 13 1 AM 50BAE 5018 4 13 a Hinge Reversal E 13 2 AM 50BAE DS AM 50BAE ADDS sse 15 a Overlay Panel Fabrication and Attachment 15 BES E 23 E Electrical Connection EE 23 F Water Supply and Drain Connections sss eee eee eee eee eee 24 G Final Checklist EEN 25 e E E TA LUT o TTT 26 III Cleaning and Maintenance rennen 27 A Cleaning and Sanitizing Instruccions eee
13. com 91A1VG10E
14. ctric shock or fire To unplug the unit be sure to pull the plug not the cord and do not jerk the cord 7 To reduce the risk of electric shock do not touch the plug or control switch with damp hands 8 The GREEN ground wire in the factory installed power cord is connected to a screw on the rear panel where the cord enters the unit If it becomes necessary to remove or replace the power cord be sure to connect the power cord s ground wire to this screw upon reattachment Usually an electrical permit and services of a licensed electrician are required The maximum allowable voltage variation is 10 percent of the nameplate rating For optional drain pump installation refer to the instruction manual included with the pump 23 F Water Supply and Drain Connections A WARNING 1 Water supply and drain connections must be installed in accordance with applicable national state and local regulations 2 Normal operating water temperature should be within 45 F to 95 F 7 C to 35 C Operation of the icemaker for extended periods outside of this normal temperature range may affect icemaker performance 3 To prevent damage to equipment do not operate the icemaker when the water supply is off or if the pressure is below 10 PSIG Do not run the icemaker until the proper water pressure is reached A plumbing permit and services of a licensed plumber may be required in some areas External filters strainers or s
15. ed to ensure that the hardware fasteners do not interfere with the overlay panel fitting flush with the door 5 While maintaining a hold on the door remove the hinge stop pin from hinge B Pull out the bottom of the door slightly and gently remove the door from hinge A See Fig 10 If you are leaving the door right hinged skip to step 7 If you would like to reverse the door hinges proceed to step 6 6 If you would like to reverse the door hinges do the following a Contact your local distributor to purchase Hoshizaki Kit HS 0229 The kit contains hinge A left b Remove the 2 screws securing the top panel then lift it off See Fig 11 c Remove hinge A right and the bracket from the right side of the unit Set aside hinge A right it is not needed Remove the top brace from the left side Fasten hinge A left and the bracket to the left side and the top brace to the right side See Fig 12 Note When on the proper side the gasket notch for hinge A is to the inside Screws Bracket __ Crew Top Panel J Hinge A Left l n Screw m Top Brace UEL SS E X Fig 11 Fig 12 d Remove hinge B from the right side of the unit and the 2 filler screws from the left side Attach the 2 filler screws to the right side and attach hinge B to the left side See Fig 13 e Rotate the top panel 180 from its previous position This brings the notch that
16. forwarded to the factory for warranty registration 25 H Startup A WARNING 1 All parts are factory adjusted Improper adjustments may adversely affect safety performance component life and warranty coverage 2 If the icemaker is turned off wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor 3 At startup confirm that all internal and external connections are free of leaks 1 Open the water supply line shut off valve 2 Make sure the control switch is in the OFF position Plug the unit into the electrical outlet If you have to slide the unit back for a built in installation make sure you do not damage or pinch the water supply drain connections or power cord 3 If required by sanitation code in your area seal the perimeter where the machine touches the floor with approved caulk compound in a smooth and easily cleanable manner 4 Move the control switch to the ICE position and allow the icemaker to operate for 2 minutes This allows the water tank to fill 5 Move the control switch to the OFF position 6 Inside the storage bin disconnect the suction tube by squeezing the tabs and pulling the tube clear See Fig 31 Allow the water tank to drain 7 Reconnect the suction tube as illustrated See Fig 32 Make sure the tabs lock into place a loose fitting may cause a water leak Water Tank Tabs Suction Tube Suction Tube Fig 31 Fig 32 8
17. h skin or eyes 4 After cleaning and sanitizing be careful not to leave any cleaning or sanitizing solution in the icemaker 1 Cleaning Solution IMPORTANT For safety and maximum effectiveness use the solution immediately after dilution Dilute 5 fl oz 148 ml or 10 tbs of Hoshizaki Scale Away with 1 gallon 3 8 I of warm water This is a minimum amount Make more solution if necessary 2 Cleaning Procedure 1 Remove all ice from the evaporator and the storage bin Note To remove cubes on the evaporator move the control switch to the OFF position and then move it back to the ICE position after 3 minutes The harvest cycle starts and the cubes will be removed from the evaporator 2 Move the control switch to the OFF position 27 3 Inside the storage bin disconnect the suction tube by squeezing the tabs and pulling the tube clear See Fig 33 Allow the water tank to drain 4 Reconnect the suction tube as illustrated See Fig 34 Make sure the tabs lock into place a loose fitting may cause a water leak Tabs Water Tank Tabs Suction Tube Suction Tube Fig 33 5 Slowly pour the cleaning solution into the water tank 6 Move the control switch to the WASH position 7 Allow the cleaning solution to circulate for 30 minutes then move the control switch to the OFF position 8 Disconnect the suction tube Allow the water tank to drain then reconnect the suction tube 9 Move the contro
18. icemaker 1 Stainless Steel Exterior To prevent corrosion wipe the exterior occasionally with a clean and soft cloth Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up 2 Storage Bin and Scoop Wash your hands before removing ice Use the plastic scoop provided The storage bin is for ice use only Do not store anything else in the storage bin Clean the scoop and the storage bin liner using a neutral cleaner Rinse thoroughly after cleaning 3 Condenser Check the condenser once a year and clean if required by following the steps below More frequent cleaning may be required depending on location A WARNING 1 Move the control switch to the OFF position and unplug the unit from the electrical outlet before cleaning the condenser 2 Condenser fins are sharp Use care when cleaning 1 Move the control switch to the OFF position and unplug the unit from the electrical outlet 2 Remove the 2 screws securing the front panel then Condenser Front Panel remove the panel See Fig 47 Screws EN EN 9 3 Remove the 2 screws securing the louver then remove the louver 4 Use a brush attachment on a vacuum cleaner to gently clean the condenser fins Do not use too Bech i Z much force otherwise the fins could be damaged 5 Replace the louver and front pane
19. ide a firm foundation for the icemaker This icemaker requires no side or top clearance But allow enough space at rear for water supply and drain connections and at least 15 88 cm clearance at front 11 2 Built In Installation Site CAUTION 1 Do not let the weight of the counter rest on the icemaker 2 Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service Installation Space AM 50BAE AM 50BAE DS 34 864 mm minimum 15 381 mm minimum 24 610 mm minimum AM 50BAE AD AM SOBAE ADDS 32 814 mm minimum Between Two Cabinets AM 50BAE AM 50BAE DS Min 15 Min 34 381 mm 864 mm AM 50BAE AD AM 50BAE ADDS Min 32 814 mm Between a Cabinet and a Wall or Tall Cabinet Secure Do not let the weight of the counter rest on the icemaker AM 50BAE ADDS Between a Cabinet and the End of a Counter AM 50BAE MEUS Min Tac Support Do not 864 am 381mm fet the weight of AM 50BAE AD the counter rest on the icemaker Min 32 814 mm In a Corner cemaker SS C Door 1 AM 50BAE AM 50BAE AD a Hinge Reversal If you would like to reverse the door hinges follow the steps below Otherwise skip to section ID Setup 1 While maintaining a hold on the door remove the hinge stop pin from hinge B Pull out the bottom of the door slightly and gently
20. l in their correct Screws BR Louver positions Ensure that the screws are securely in place Fig 47 6 Plug the unit back in Move the control switch to the ICE position to start the automatic icemaking process 32 C Preparing the Icemaker for Long Storage CAUTION When storing the icemaker for an extended time or in sub freezing temperatures follow the instructions below to prevent damage When the icemaker is not used for two or three days under normal conditions it is sufficient to move the control switch to the OFF position When storing the icemaker for an extended time or in sub freezing temperatures follow the instructions below 1 Close the water supply line shut off valve then open the water supply line drain valve See Fig 30 2 Allow the line to drain by gravity 3 Attach a compressed air or carbon dioxide supply to the icemaker water supply line drain 4 Move the control switch to the ICE position 5 Blow the icemaker water supply line out using the compressed air or carbon dioxide supply 6 Close the icemaker water supply line drain valve 7 8 9 Remove all ice from the storage bin Clean the storage bin liner using a neutral cleaner Rinse thoroughly after cleaning Move the control switch to the OFF position Unplug the icemaker 33 HOSHIZAKI AMERICA INC 618 Hwy 74 S Peachtree City GA 30269 USA TEL 770 487 2331 FAX 770 487 3360 www hoshizaki
21. l switch to the ICE position and allow the icemaker to operate for 2 minutes This allows the water tank to fill with water 10 Move the control switch to the WASH position 11 Allow the water to circulate for 5 minutes then move the control switch to the OFF position 12 Disconnect the suction tube Allow the water tank to drain then reconnect the suction tube 13 Repeat steps 9 through 12 three more times to rinse thoroughly 28 3 Sanitizing Solution IMPORTANT For safety and maximum effectiveness use the solution immediately after dilution Dilute 0 5 fl oz 14 8 ml or 1 tbs of a 5 25 sodium hypochlorite solution chlorine bleach with 1 gallon 3 8 I of warm water This is a minimum amount Make more solution if necessary Using a chlorine test strip or other method confirm that you have a concentration of about 200 ppm 4 Sanitizing Procedure 1 Make sure the control switch is in the OFF position and the storage bin is empty 2 Remove the slope from the storage bin by carefully bending it in the center and releasing it from the 2 slope shafts See Fig 35 3 Remove each separator by lifting it to the horizontal position and pushing it hard inward See Fig 36 4 Disconnect the suction tube Allow the water tank to drain 5 Spread out the tabs to unlock the water tank then slide it out See Fig 37 6 Lift off the ice chute from the front frame pipe and then from the rear frame
22. lay panel from the door 12 Drill 3 8 diameter holes 1 4 7 mm deep where you marked on the overlay panel to accommodate the hinge C1 and hinge C2 bushings 20 4 Attachment of Overlay Panel to Door 1 Fasten the sheet metal bracket to the overlay panel using the two M4x8 truss head screws provided Snug the screws but do not tighten See Fig 20 2 Temporarily fasten the overlay panel to the door using 2 of the M4x25 pan head screws provided See Fig 21 f el Overlay Panel mi Screws Snug the screws but do not tighten Sheet Metal Bracket Fig 20 Fig 21 3 Adjust the sheet metal bracket so that it is flush with the bottom of the door See Fig 22 4 Remove the overlay panel from the door and tighten the two M4x8 truss head screws securing the sheet metal bracket to the overlay panel See Fig 23 Overlay Panel Tighten the screws A Door d D GH d ag 8 8 B oo z SC sn heet Metal Bracket snper Metal Bracke Sheet Metal Bracket Fig 22 Fig 23 5 Fasten the overlay panel to the door using the four M4x25 pan head screws provided Snug the screws but do not tighten See Fig 24
23. ofteners may be required depending on water quality Contact your local Hoshizaki distributor for recommendations Water supply inlet is 1 2 female pipe thread FPT A minimum of 1 4 nominal ID copper water tubing or equivalent is required for the water supply line A water supply line shut off valve and drain valve should be installed Water supply pressure should be a minimum of 10 PSIG and a maximum of 113 PSIG If the pressure exceeds 113 PSIG the use of a pressure reducing valve is required Drain outlet is 1 2 FPT A minimum of 1 2 nominal ID hard pipe or equivalent is required for the drain line Drain line should not be piped directly to the sewer system An air gap of a minimum of 2 vertical inches 5 cm should be between the end of the drain pipe from the icemaker and the floor drain For gravity drain installation drain line must have 1 4 fall per foot 2 cm per 1 m on horizontal runs to get good flow A vented tee connection is also required for proper flow For optional drain pump installation refer to the instruction manual included with the pump Minimum 1 4 Nominal ID u Copper Water Tubing 2 OF Water Supply Inlet 1 2 FPT Drain Outlet 1 2 FPT Water Supply Line Shut Off Valve J Water Supply Line Ti XH Drain Valve Piping to approved drain Leave a 2 inch 5 cm vertical air gap between the end of the pipe and the drain Vent Tube
24. ok each separator onto the rail then pull it hard towards you until it locks into place See Fig 45 17 Replace the slope in its correct position See Fig 46 Separator Slope 18 19 20 21 Discard the sanitizing solution Mix a new batch of the sanitizing solution and slowly pour it into the water tank Move the control switch to the WASH position After circulating the sanitizing solution for 15 minutes move the control switch to the OFF position 22 Disconnect the suction tube Allow the water tank to drain then reconnect the suction tube 23 Repeat steps 19 through 22 one time 24 Move the control switch to the ICE position and allow the icemaker to operate for 2 minutes This allows the water tank to fill with water 25 Move the control switch to the WASH position 26 Alow the water to circulate for 5 minutes then move the control switch to the OFF position 27 Disconnect the suction tube Allow the water tank to drain then reconnect the suction tube 28 Repeat steps 24 through 27 two more times to rinse thoroughly 29 Clean the storage bin liner door liner and door gasket with a neutral cleaner Rinse thoroughly after cleaning 30 Move the control switch to the ICE position to start the automatic icemaking process 31 B Maintenance IMPORTANT This icemaker must be maintained individually referring to the instruction manual and labels provided with the
25. screws in the remaining 2 holes See Fig 6 7 Attach the door to hinge A then continue to maintain a hold on the door Screw the hinge stop pin into hinge B until it is tight See Fig 7 Screws Fig 6 Hinge Stop Pin Fig 7 2 AM 50BAE DS AM 50BAE ADDS a Overlay Panel Fabrication and Attachment IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results 1 Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag ay ol A 15 2 Overlay Panel Specification Use the specification that applies to your icemaker AM 50BAE DS or AM 50BAE ADDS and the directions that follow to prepare your overlay panel a AM 50BAE DS 14 13 16 376 mm 14 16 A Threaded Inserts 12 13 16 29 17 32 750 mm B Threaded Inserts 3 16 Depth 4 mm AM 50BAE DS Overlay Panel Specification Overlay Panel Height 29 17 32 750 mm Overlay Panel Width 14 13 16 376 mm Overlay Panel Thickness 5 8 16 mm minimum 3 4 19 mm maximum Overlay Panel and Door Weight total 20 Ib 9 kg maximum 16 b AM 5OBAE ADDS 14 13 16 376 mm 13 1 2 14 16 23 mm 12 13 16 27 9 16 700 mm 3 16 Depth 4 mm AM 50BAE ADDS Overlay Panel Specification Overla
26. side to side and front to rear by adjusting the feet E Electrical Connection A WARNING 1 Electrical connection must meet national state and local electrical code requirements Failure to meet these code requirements could result in death electric shock serious injury fire or severe damage to equipment 2 This unit requires an independent power supply See the nameplate for proper voltage and breaker fuse size Failure to use a proper breaker or fuse can result in a tripped breaker blown fuse or damage to existing wiring This could lead to heat generation or fire THIS UNIT MUST BE GROUNDED This unit is equipped with a 3 prong grounding plug to reduce the risk of potential shock hazards It must be plugged into a properly grounded independent wall outlet If the outlet is a 2 prong outlet it is your personal responsibility to have a qualified electrician replace it with a properly grounded independent 3 prong wall outlet Do not remove the ground prong from the power cord and do not use an adapter plug Failure to follow these instructions may result in death electric shock or fire Do not use an extension cord Make sure the control switch is in the OFF position before plugging in or unplugging the unit to reduce the risk of electric shock Do not use a unit with a damaged power cord The power cord should not be altered jerked bundled weighed down pinched or tangled Such actions could result in ele
27. sk of potential shock hazards It must be plugged into a properly grounded independent wall outlet If the outlet is a 2 prong outlet it is your personal responsibility to have a qualified electrician replace it with a properly grounded independent 3 prong wall outlet Do not remove the ground prong from the power cord and do not use an adapter plug Do not use an extension cord Make sure the control switch is in the OFF position before plugging in or unplugging the unit to reduce the risk of electric shock Do not use a unit with a damaged power cord The power cord should not be altered jerked bundled weighed down pinched or tangled Such actions could result in electric shock or fire To unplug the unit be sure to pull the plug not the cord and do not jerk the cord To reduce the risk of electric shock do not touch the plug or control switch with damp hands This unit should be disassembled or repaired only by qualified service personnel to reduce the risk of electric shock injury or fire Do not make any alterations to the unit Alterations could result in electric shock injury fire or damage to the unit L Specifications A Construction
28. tallation Visually inspect the exterior of the shipping container and immediately report any damage to the carrier Upon opening the container any concealed damage should also be immediately reported to the carrier Remove the shipping carton tape and packing material If any are left in the icemaker it will not work properly Remove the package containing the accessories Remove the protective plastic film from the panels If the icemaker is exposed to the sun or to heat remove the film after the icemaker cools See the nameplate on the left side panel and check that your voltage supplied corresponds with the voltage specified on the nameplate B Location 1 General This icemaker is approved for indoor or outdoor use CAUTION 1 Normal operating ambient temperature should be within 45 F to 100 F 7 C to 38 C Normal operating water temperature should be within 45 F to 95 F 7 C to 35 C Operation of the icemaker for extended periods outside of these normal temperature ranges may affect icemaker performance 2 This icemaker will not work at sub freezing temperatures To prevent damage to the water supply line drain the icemaker if the air temperature is going to go below 32 F 0 C See III C Preparing the Icemaker for Long Storage For best operating results The icemaker should not be located next to ovens grills or other high heat producing equipment The location should prov
29. y Panel Height 27 9 16 700 mm Overlay Panel Width 14 13 16 376 mm Overlay Panel Thickness 5 8 16 mm minimum 3 4 19 mm maximum Overlay Panel and Door Weight total 20 Ib 9 kg maximum 17 3 Fabrication of Overlay Panel Fabricate the overlay panel as outlined in the applicable specification on the previous pages and the instructions below 1 Rout a channel at the bottom of the overlay panel to the proper dimensions See C Routed Area in the specification diagram and Fig 8 2 Drill six 1 4 diameter hardwood may require slightly larger diameter holes 3 8 10 mm deep in the locations designated See A Threaded Inserts and B Threaded Inserts in the specification diagram and Fig 9 CAUTION Use care when drilling holes for mounting hardware All drilled holes must be straight and drilled to the correct diameter and depth Holes Holes Routed Channel Fig 8 Fig 9 3 Screw the 6 threaded wood inserts into the 1 4 holes drilled in the previous step Make sure that the inserts are threaded straight and that the tops of the inserts are flush to the overlay panel surface Otherwise the overlay panel cannot be properly fastened to the door 4 Mount the door handle hardware Hoshizaki recommends that the door handle hardware be mounted on the edge opposite of the door hinge side optional hinge reversal is covered in step 6 Countersunk screw heads are requir
Download Pdf Manuals
Related Search