Honeywell HRDP DVR DVR User Manual
Contents
1. N7 button until the new zone number appears in the display After you stop pressing the button the display will show a compass heading within a few seconds SS os 1 lt a 2 gt 2 e f AN d TW A NN SZ To Operate the Temperature Feature 1 Push the Ne switch The vehicle s directional heading and outside temperature will be displayed 2 Pushing the N switch a second time will turn off the visual display 3 The temperature display can be changed to Celsius by depressing the 7 switch for 3 seconds until a C appears by itself in the display window Pushing the N7 switch again will toggle the display between Celsius and Fahrenheit Five seconds of no switch activity returns the display to its normal directional and temperature reading HomeLink and the HomeLink house are registered trademarks of Johnson Controls Inc To Operate the HomeLink Feature Please refer to the programming instructions outlined in this User Guide or a visit the HomeLink website at www homelink com b call the HomeLink customer support line at 1 800 355 3515 HomeLink Programming Instructions WARNING Before programming HomeLink to a garage door opener or gate operator make sure that people and objects are out of the way of the device to prevent potential harm or damage When programming a garage door opener it is advised to park outside of the ga2. 9 Return to the vehicle and firmly press hold for 2 seconds and release the programmed HomeLink button Fig 5 10 Repeat Step 9 a second time and possibly a third time depending on Hold for 2 seconds and release brand of device HomeLink should now activate your rolling code equipped device Gate Operator Canadian Programming Canadian radio frequency laws require transmitter signals to time out or quit after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming Similar to this Canadian law some U S gate operators are designed to time out in the same manner If you live in Canada or you are having difficulties programming a gate operator by using the Programming procedures regardless of where you live replace Programming HomeLink step 4 with the following NOTE If programming a garage door opener or gate operator it is advised to unplug the device during the cycling process to prevent possible overheating 4 Continue to press and hold the HomeLink button while you press and release every 2 seconds cycle your hand held transmitter until the frequency signal has successfully been accepted by HomeLink The indicator light will flash slowly and then rapidly Proceed with Programming step 5 to complete NOTE Programmed HomeLink codes can be intentionally erased when selling vehicle etc by hol
3. d of temperature a These problems must be corrected at your authorized Dealer Service Center FCC NZLCTHL3 IC 4112A NZLCTHL3 Po Auto Dimming Mirror User Guide Congratulations Your new Mazda is equipped with an Automatic Dimming Mirror manufactured by Gentex Corporation During nighttime driving this safety feature will automatically detect and eliminate dangerous rearview mirror glare Your new mirror may or may not have all of the features shown in this User Guide Please refer only to the sections that pertain to the model mirror you have in your new vehicle Auto Dimming Mirror with Compass DISPLAY WINDOW ON OFF To Operate the Auto Dimming Feature Push the switch to turn the mirror on off The auto dimming feature is enabled when the green LED indicator is on To Operate the Compass Feature 1 Push the display O switch The vehicle s directional heading will be displayed 2 Pushing the switch a second time will turn off the visual display 3 If the display reads C calibrate the compass by driving the vehicle in up to 3 complete circles at less than 5 MPH CALIBRATION PROCEDURE C in window indicates unit needs to be calibrated y N A 360 360 I 1 R I em et 4 To adjust for compass variance a Press the button for more than 9 seconds or until the current zone number appears in the display b Find your current locatio
4. ding the 2 outer buttons as shown in Fig 1 for 20 seconds until LED indicator begins to flash Do not hold buttons for more than 30 seconds If you have any questions or are having difficulty programming your HomeLink buttons please refer to www homelink com or call 1 800 355 3515 Cleaning the mirror When cleaning the mirror use a paper towel or similar material dampened with glass cleaner Do not spray glass cleaner directly onto the mirror as damage to internal circuitry may result Troubleshooting Guidelines 1 C or CAL is displayed in the display window a Perform calibration procedure 2 Inaccurate compass direction a Perform compass Zone setting procedure and then calibration procedure b Vehicle magnetics may have changed Press and hold the button or the oN button if mirror has for 9 seconds until a C or CAL appears in the display window Perform calibration procedure NOTE Installing items such as a ski rack antenna luggage rack or recent body repair can cause changes to the vehicle s magnetic field This may require that the compass be recalibrated by performing the recalibration procedure 3 The temperature display is reading significantly low a The temperature display may have been changed to degrees Celsius Refer to the section of this User Guide pertaining to the temperature feature to correct 4 The display window shows SC or OC instea
5. es from a slow to a rapidly blinking light release both the HomeLink and hand held transmitter buttons Press button 6 Press and hold the just trained HomeLink PEAR button and observe the indicator light seconds then constant rolling code g aU If the indicator light blinks rapidly for 2 seconds and then turns to a constant light the device being programmed utilizes rolling code and programming is not complete until the following steps are completed Fig 3 7 On the garage door opener receiver motor head unit locate the learn or smart button This can usually be found where the hanging antenna wire is attached to the motor head unit 8 Firmly press and release the learn or smart button Fig 4 Press Learn button eH CONDS 16 CE TO NEHICIE NOTE You have 30 seconds to initiate step 9
6. n and variance Zone number on the Zone map below c Press the button until the new zone number appears in the display After you stop pressing the button the display will show a compass heading within a few seconds KE ZING SIIN Z E 550 0351 B Auto Dimming Mirror with Compass and HomeLink and Auto Dimming Mirror with Compass HomeLink and Temperature DISPLAY WINDOW Larger window for Temp model HOMELINK BUTTONS AUTO DIMMING ON OFF BUTTON DISPLAY To Operate the Auto Dimming Feature Push the switch to turn the mirror on off The auto dimming feature is enabled when the green LED indicator is on To Operate the Compass Feature 1 Push the display Ne switch The vehicle s directional heading will be displayed 2 Pushing the switch a second time will turn off the visual display 3 If the display reads C or CAL calibrate the compass by driving the vehicle in up to 3 complete circles at less than 5 MPH CALIBRATION PROCEDURE C or CAL in window indicates unit needs to be calibrated y a x s 5 Pa Pa A A D D ios X d 4 To adjust for compass variance a Press the N button for more than 9 seconds or until the current Zone number appears in the display b Find your current location and variance zone number on the zone map below c Press the
7. rage Do not use HomeLink with any garage door opener that lacks safety stop and reverse features as required by U S federal safety standards this includes any garage door opener model manufactured before April 1 1982 A garage door that cannot detect an object signaling the door to stop and reverse does not meet current U S federal safety standards For more information contact HomeLink at www homelink com or by calling 1 800 355 3515 1 To begin press and hold the 2 outer HomeLink buttons to clear memory until the indicator light LED blinks slowly approximately 20 seconds Fig 1 2 Release both buttons NOTE Do not hold the buttons for longer than 30 seconds Do not repeat this step when programming additional devices to remaining Press and Hold for 20 seconds LED blinks slowly buttons Release buttons 3 Position the end of the hand held transmitter 1 3 inches away from the HomeLink button you wish to program while keeping the Peca bein the indicator light in view LED blinks fast Relea ne Doth buttons 4 Simultaneously press and hold both the chosen HomeLink and hand held transmitter buttons Fig 2 Do not release the buttons until step 5 has been completed NOTE Some gate operator and garage door Openers may require you to replace this Programming step 4 with procedures noted in the Gate Operator Canadian Programming section 5 After the HomeLink indicator light chang
Download Pdf Manuals
Related Search