Hitachi BD-W85TAE Washer User Manual
Contents
1. 1 Untighten the upper connector 2 Push the upper connector up screw till the rubber packing is in Rubber packing connector Upper connector In case the diameter of the tap us is large remove the guide plate Middle connector CJ e Turn the middle connector so that there is no water leak Connector 3 Connect the water supply e To separate the water hose to the middle connector supply hose from the middle pushing the plate down connector turn off the tap and then pull the inlet hose down pushing the plate down Middle connector Water supply hose 26 3WPL090501 How to Install the Washing Machine E Make sure that the union nut between the water supply hose and main unit is tightly screwed E Turn the tap on to check if the water supply hose is properly connected before starting If it is loosely connected water leakage may occur e Drain hose E The drain hose should be placed higher than 60 cm above and not higher than 100 cm above the floor If the drain outlet is lower than 60 cm a joint pipe is necessary additional part sold at a specialist outlet Secure the drain hose to prevent from 60 100 cm slipping out from joint pipe Joint pipe E Do not bend twist crush or pull out bend or step on the drain hose Use the hose guide to prevent the drain hose from kinking E Do not detach the drain hose from the rear panel of the washing machin2. E The washing machine starts to detect laundry size fabric type and water temperature before setting the wash time E The wash time displayed on the remaining time indicator varies according to the conditions gt Page 8 Control Panel and Display E Once a program starts settings cannot be changed except for the spin speed setting of programs other than the Cotton Cotton Eco programs 11 3WPLO090501 How to Use the Washing Machine E Pausing a program Press the Start Pause button The washing machine switches itself off if it is not restarted within 1 hour Switch the power on and the program starts again from the beginning E Adding clothes part way through a wash Press the Start Pause button to pause the selected program The door lock is automatically released after about 5 seconds when the water level and temperature are safe You can then open the door and add your clothes Close the door and press the Start Pause button again to restart the program Note It is not recommended to add a large amount of clothes as the washing machine first measures the load size to determine optimum operation E Terminating a program Press the Start Pause button and press the Power button to switch power off Then press the Power button again and select the Spin or Drain program to drain remaining water in the drum and spin dry the laundry 6 Program ends E The buzzer sounds when the program ends By pressing the Spin button
3. Fabric Laundry Spin speed Type Size No of rinses 15 3WPL090501 Program Max Load baat Spin Setting Type of Laundry N etting 400 1200r min For daily washing of cotton and linen items su O Cotton 8 5 kg 30 90 C No Spin Rinse Hold towels bed linen and table linen ene 400 1200r min For cotton and linen items Eco operation that Coron Eco 8 5 kg 30 600 No Spin Rinse Hold provides the same washing performance as tt This lets you wash small loads of lightly soilec Rapid 15 2kg 30 C 400 800r min such as underwear in 15 minutes Its also ide No Spin Rinse Hold clothes 400 1000r min For washing normally soiled blouses shirts et 600 Synthetic 4kg 30 60 C No Spin Rinse Hold or blends with cotton 400 1200r min en l 0 A Mix 4kg 30 60 C No Spin Rinse Hold Lightly soiled items can be washed together wi F 400 800r min Gentle wash program for delicate items such Delicate 4kg 30 C 40 C No Spin Rinse Hold curtains ane 400 1200r min 3 Outdoor 4kg 40 90 C No Spin Rinse Hold For washing heavily soiled durable clothes je 400 800r min A Duvet 2 5kg 30 C 40 C No Spin Rinse Hold For washable large items such as duvets blai Gentle washing for machine washable wooler Wool 2kg De Noe aa pg ea pin This program is tested and approved by Wool 400 1200r min Removes allergens such as house dust mites Allergy Care 4kg 90 C No Spin Rin
4. 1 Place a shallow container near the drain tube 2 Remove the cap and drain water into the container Drain tube Cap 4 Place a piece of cloth under the filter cover Turn the drain filter anticlockwise slowly and remove it Make sure to open the drain filter slowly as hot water may come out 5 Remove foreign objects such as coins or pins Clean inside the drain filter and the drain pump with a brush Drain filter Remove 6 Return the cap drain filter and the filter cover in reverse order 19 3WPLO090501 Care and Maintenance Cleaning the 1 Remove the detergent dispenser detergent a dispenser 4 Push the dent a 2 Pull the detergent dispenser while pushing the dent 2 Remove dirt or detergent remaining in the detergent dispenser casing with a brush Detergent dispenser casing Pa 3 Wash the detergent dispenser with water Use a brush for narrow parts or parts from which it is difficult to remove dirt E How to remove and set the softener cap Pull up to remove Push down firmly to set Cleaning the 1 Turn off the tap water inlet filter 2 Remove the water supply hose from the rear panel of the washing machine 3 Remove the water inlet filter and clean with a brush e C Water inlet filter mm Pull out to remove 4 Return the water inlet filter and the water supply hose to their original positions E External cleaning Maintenance Clean the surface of the washin
5. 800 r min 0 15kwh 30L 0 15h Synthetic 4kg 40 C 800 r min 0 43kwh 42L 1 04h Mix 4kg 40 C 800 r min 0 59kwh 79L 1 18h Delicate 4kg 40 C 800 r min 0 53kwh 55L 1 32h Outdoor 4kg 60 C 1000 r min 1 14kwh 75L 2 02h Duvet 2 5 kg 30 C 800 r min 0 40kwh 79L 1 30h Daily 60 6 kg 40 C 800 r min 0 65kwh 63L 0 56h Allergy Care 4kg 90 C 1000 r min 2 16kwh 112L 2 47h Wool 2 kg 30 C 400 r min 0 32kwh 63L 0 56h Crease Care 4kg 40 C 800 r min 0 75kwh 77L 1 50h compliance with EN60456 IEC60456 standards Program temperature option and spin speed are used to measure the data entered in energy label in Consumption values may differ from the indicated values depending on the water pressure water hardness water inlet temperature ambient temperature type and amount of laundry and degree of soiling detergent brand and selected options Specifications Model BD W85TAE Power supply See the rating plate attached to the rear of the washer Standard water level 23L Highest water level Standard amount of water used 49L Cotton Eco course Water pressure 0 03 0 8 MPa 0 3 8 Kgf cm Dimension W 600 mm x D 624 mm x H 850 mm Weight 67 kg 31 3WPLO090501 3WPLO90501 3WPLO090501
6. Tub Clean program along with the Auto Self Clean function E The Auto Self Clean function is deactivated if one of the following programs is selected Duvet Rapid 15 Wool Daily 60 Tub Clean Spin Drain 13 3WPLO090501 How to Use the Washing Machine How to use the Memory function How to use the Duvet program 14 3WPL090501 1 Press the Power button to turn on the power 2 Select and adjust the program as desired 3 Press the Memory button for 3 seconds then the setting is memorized 4 Press the Start Pause button E Once the setting is saved the customized program can be selected with just a press of the Memory button E Customized program can be changed by doing the same procedure Note Do not use blanket net This may cause excessive vibration when spinning 1 Load the laundry E Fold a large items such as a duvet or blanket as follows E Load laundry into the drum with the ends facing the rear of the drum Drum Laundry ends facing rear of drum Push laundry inside i not to exceed this line 2 Press the Power button to switch power on 3 Select the Duvet program 4 Add detergent into the detergent dispenser 5 Press the Start Pause button How to Use the Washing Machine How to use the Tub Clean program Eco friendly operation Washable Items with the Duvet program e Washable Duvets Machine washable duvets stuffed with not more tha
7. If any of the following conditions or other abnormalities occur immediately pull out the power plug to prevent an accident and contact your local service center E The washing machine does not operate when you switch power on E The power cord has cracks E There are abnormal vibrations and sounds during operation E There is a smell of burning Select the Cotton program with water temperature at 60 C setting and allow the unit to wash without clothing This will remove residues and water that may have been left in the drum during manufacturing Customer Service In case of malfunction of the washing machine please check these Operating amp Installation instructions carefully before you call for repair services If you are unable to identify or solve the problem please contact your local service center Before calling make a note of the model name serial no and purchase date of your washing machine You can find the model name and serial no on the label attached to the filter cover Model Name BD W85TAE Serial No XXXXXXXX kA Consumption Values l l Consumption value Time Program Load Temperature Option Spin speed Beak Waler about Cotton 8 5 kg 40 C 1000 r min 0 76kwh 85L 1 33h 40 C 1000 r min 0 75kwh 49L 2 53h Cotton Eco 8 5 kg 60 C Intensive 1200 r min 1 20kwh 49L 3 28h Rapid 15 2kg 30 C
8. The water supply filter may be clogged Washing time may be prolonged if the load is unbalanced as the washing machine tries to correct the imbalance Washing time may be prolonged when there is too much foam as the additional action of eliminating it is necessary The remaining time is continually corrected and may change during the program The amount of foam varies depending on the temperature level of soiling and water hardness Detergent may remain undissolved if it is poured directly into the drum You may have used too much detergent The amount of foam varies depending on the temperature level of soiling and water hardness You may not have selected the Prewash option The detergent in the dispenser Wj is for prewash only If there is imbalance in the drum rinsing restarts automatically to correct it for safety reasons If there is imbalance in the drum the washing machine tries to correct the imbalance by repeatedly rotating and stopping Intermittent spinning of the tub helps the spin process to operate quietly The laundry may be too light Run the Drain program to drain water e Deactivate the child lock See page 8 Push the Power button to switch power on The door lock will be released if there is no water in the drum e Deactivate the child lock See page 8 Turn on the water tap Make sure that the water supply hose is not frozen Straighten the water inle
9. a long time E All transport bolts must be removed before using the washing machine gt They may cause abnormal vibration or failure E Check inside the drum before washing gt Make sure that small pets do not climb into the drum E Do not wash waterproof items such as raincoats wet suits ski suits sleeping bags cushions pillows shoes etc gt The washing machine may not work properly or the items may cause injury or damage the machine E Do not operate without the detergent dispenser E Do not use tap water hotter than 50 C E Do not wash items together with coins pins or stones gt This may damage clothes and the washing machine and cause a water leak Check inside pockets before washing E Do not press the buttons with sharp or pointed objects E Be careful when draining hot water E Do not lean on or put weight on the opened door of the washing machine gt This may cause damage to the washing machine Do not attempt to open the door while it is operating E Do not put heavy objects liquid filled containers or equipment which produces heat e g oven rice cooker etc on the washing machine gt This may damage the washing machine or the surface of the worktop E f detergent fabric softener or bleach spills on the surface of the machine clean it up with a damp cloth immediately gt The plastic or steel parts of the washing machine may get damaged E Do not place heat sources near the washing machine g
10. for 3 seconds After press Power button the buzzer sound is deactivated By pressing the Spin button again the buzzer sound is reactivated E The washing machine automatically switches itself off when the program ends 12 3WPL090501 How to Use the Washing Machine How to use the Auto Self Clean function 1 Press the Power button to turn on the power 2 Select a program 3 Press the Auto Self Clean button and then press the Start Pause button E The setting is switched off at the time of shipment from the factory Once it is switched on the Auto Self Clean function operates every time you do your laundry E Prior to the final spin cycle the outside of the tub and the inside of the outer tub are washed to eliminate dirt and mold E To deactivate the Auto Self Clean function press the Auto Self Clean button again while the power is on The Auto Self Clean function runs just before the spin cycle begins in each program The Auto Self Clean function cannot be set or cancelled while the washing machine is operating The Auto Self Clean function is automatically cancelled when Rinse Hold is set No spinning is set Depending on the type and degree of dirt some dirt may not be removed by using the Auto Self Clean function f the washing machine is seldom used some dirt may not be removed by using the Auto Self Clean function To clean the tub more completely we recommend using the
11. gt Page 20 Care and Maintenance Cleaning the detergent dispenser E Do not use liquid detergent when using the Prewash option E The detergent and any additives must be poured into the appropriate dispenser gt Page 6 Product Descriptions Detergent Dispenser E Pour in the detergent before you press the Start Pause button If you add the Prewash option pour detergent into both dispensers Ul before starting E For dyeing and bleaching use dyes and bleaches that are suitable for washing machines E For water softener and limescale removal agents follow the instructions on the package Washing with E Lightly to normally No washing options Prewash Intensive are different degrees soiled necessary for more eco friendly operation of soiling E Normally to heavily Select Intensive as an option for better washing soiled results E Heavily soiled Select Prewash as an option for better washing results 10 3WPLO090501 fad fm How to Use the Washing Machine Je d ed w or Q Sort and load the laundry Press the Power button to switch power on 3 Select and adjust the program 4 Add detergent amp Wool Crease Care Allergy Care Outdoor Tub Clean Rinse amp Spin o Daily 60 o Rapid 15 Synthetic o Delicate o Duvet Cotton Eco pin Drain Tempt Spinirimin P
12. mark cut modify bend or fold the power cable gt A damaged power cable could cause fire or an electric shock E Do not use a mains plug adaptor or an extension cable gt This could cause overheating which may cause a fire E f the power supply plug is damaged it must only be replaced by the authorized service agent or repairing shops appointed by the manufacturer in order to avoid a hazard 3WPLO90501 Safety Instructions or Child safety VAN Caution General safety Use Care and maintenance E Keep packaging out of reach of children and babies gt Danger of suffocation E Do not let children climb onto the washing machine or open the drum door and do not leave a box or chair near the washing machine which could enable children to climb onto it gt This may cause injury E Children should be supervised to ensure that they do not play with the appliance Issues which could cause injury or damage your belongings E f there is a water outage or you remove the water supply hose and reattach it turn off the tap and press the Start Pause button then turn on the tap slowly after 40 seconds gt Air pressure could damage the washing machine if there is a lot of air in the water pipe E Regularly check to confirm that the union nut of the water supply hose is tightened gt A loose nut may cause a water leak E Remove the plug from the socket and turn off the water tap if you don t use the machine for
13. EN Operating amp Installation Instructions HITACHI Front Loading Washing Machine Inspire the Next Model BD W85TAE Environmentally Friendly Waste Disposal 3 Hints and Tips for Eco Friendly Washing 3 Safety Instructions 4 Product Descriptions 6 Control Panel and Display 7 Before You Start Washing 9 How to Use the Washing Machine 11 Program Overview 16 In Case of Emergency 18 Care and Maintenance 19 Troubleshooting 21 Error Codes 23 How to Install the Washing Machine 24 Customer Service 30 Consumption Values 31 Specifications 31 Thank you for purchasing a Hitachi front loading washing machine E Please read these operating amp installation instructions carefully for proper operation of the machine E Please keep these operating amp installation instructions for future reference 3WPL090501 3WPLO090501 Environmentally Friendly Waste Disposal Disposing of the The shipping package has protected your new washing machine on its kagi way to your home All materials are ecologically harmless and recyclable packaging Please contribute to a better environment by disposing of packaging materials in an environmentally conscious manner Please ask your dealer or inquire at your local authorities about current means of disposal A Risk of choking Do not let children play with packaging and assoc
14. J symbol is shown on the display Laundry remains in the last rinse water without progressing to the final spin cycle to prevent the clothes from wrinkling To unload select the Spin or Drain program The symbol is shown on the display Child Lock To prevent accidental operation by children this disables the operation buttons and dial and also locks the door Press the Rinse Hold button for 3 seconds to activate this option The symbol is shown on the display Press Rinse Hold button for 3 seconds again to cancel the child lock Lets you program a wash to finish up to 24 hours later The symbol is shown on the display Allows you to store a customized wash cycle which you use frequently The 11 symbol is shown on the display 3WPLO090501 Control Panel and Display IA LED multi function Displays all cycle information remaining time and error codes display Memory Timer A Water temperature The symbol is on when the heater is off Cold setting E Spin speed No Spin Final spin is cancelled and last rinse water is drained only Prewash option D Intensive option E Remaining time of the program shows Time Left remaining time until timer operation is completed shows h and error codes gt Page 23 Error Codes F Extra Rinse option G Rinse Hold option Final spin is cancelled and water is not drained so the laundry 1l remains in the last rinse water H Imbalan
15. ance are not carried out following the installation method outlined in these instructions the manufacturer is not liable for any accident or damage caused E Do not install in a damp place such as a bathroom or a place exposed to rain gt Risk of fire electric shock current leakage or product damage E Do not install on a board with castors or an unstable surface gt This may cause injury or malfunction due to abnormal vibration Do not use a plug adapter to convert 3 pins to 2 pins The washing machine must be grounded gt This could cause an electric shock E The opening must not be obstructed by carpeting when the washing machine is installed on a carpet floor E f the washing machine is to be connected to the water mains please use new water supply hose Power source E Do not insert the plug with a wet hand gt This could cause an electric shock and cable E Use the rated mains voltage and do not connect another plug at the same socket gt Using the washing machine plug together with other electrical systems may cause overheating in the plug and result in fire E When removing the worktop to install the washing machine under a counter use a separately sold upper plate Part No BD W80MV 150 E Clean off all the dust on the plug gt A dirty or dusty plug may cause a fire E Do not use an electric socket or connection which is damaged or loose gt This could cause an electric shock or a short circuit which may start fire Do not
16. and when power is restored the same cycle automatically restarts from the beginning If the laundry has to be removed in the event of an extended power outage or in the event of malfunction of the door lock the washing machine door can be opened as follows 1 Press the Power button to switch power off when the power is on in the event of malfunction of the door lock and disconnect the mains plug 2 Drain the water in the drum from the drain tube gt See page 19 Care and Maintenance Cleaning the drain filter 3 Pull the emergency release downwards The washing machine door can be opened and the laundry can be taken out from the drum A Risk of injury Hot water may come out from the drain tube Care and Maintenance Cleaning the drain filter Drain tube Drain filter Filter cover A Risk of injury Hot water may come out from the drain tube and drain filter Do not open the drain filter when a program is running Do not clean the drain filter just after a program using hot water Do not operate the washing machine without the drain filter 1 Select the Drain program and start to drain remaining water in the drum Make sure to drain the water first otherwise a lot of hot water may come out 2 Insert a thin slim object such as a flat blade screwdriver handle of spoon fork into the slot of the filter cover and open it Slot 3 Drain out the remaining water from the drain tube Peal
17. ce in the drum gt Page 9 Control Panel and Display D Excessive foam in the drum gt Page 9 Control Panel and Display Child Lock option All buttons are disabled except the Power button and Jog Dial and the l door is locked when the symbol is on K Progress indicator Shows which phase of the program is being done The following symbols blink while each phase is running and go off as each phase ends D Prewash W Main Wash Rinse amp Spin Door lock The door is locked when the mO symbol is on M Memory option N Timer option 3WPL090501 Control Panel and Display The following symbols are displayed when washing time is prolonged due to Excessive foam in the drum gt Pouring in extra water to remove excessive foam The symbol on the left lights Imbalance in the drum gt Correcting imbalance by rotating the drum The symbol on the left lights This is not a malfunction Remaining time may be turned back when these symbols are displayed so that operation is completed in a longer time than the remaining time displayed at the start iH Auto Self Clean button Automatically cleans the outside of the tub and the inside of the outer tub to keep the washing machine clean The setting is switched off at the time of shipment from the factory Once it is switched on the Auto Self Clean function operates every time you do your laundry Before Y
18. e j Drainage into a wash basin Using the packed in hose guide Secure the drain hose to prevent it from slipping out of the wash basin The wash basin outlet must not be sealed by a plug When water is being pumped out of the washing machine check that the water drains away quickly enough Secure the connection point with 24 40 mm hose clip Sold at a specialist outlet 27 3WPL090501 How to Install the Washing Machine Connecting the E Connect the washing machine to an alternating current via a correctly installed earthed socket only power The mains voltage must correspond to the voltage specification on the washing machine E Connection specifications as well as the required fuses are stipulated on the washing machine nameplate E Do not plug the washing machine into an extension lead or power strip with multiple sockets Level Adjustment E All four adjustable feet must be firmly on the ground The washing machine must not wobble Check the alignment of the washing machine with a spirit level and adjust the feet if it s not aligned Loosen the lock nut by Loosening D 2 Lock nut unscrewing in the arrow Elevating Adjustable leg direction then stabilize the unit with the adjustable feet After adjustment tighten Tightenin ing i Lock nut BS g g the lock nut by screwing it in the arrow direction 2 Plastic base plate Tighten the lock nut until it reaches the p
19. e length E Remove the four transport bolts and insert the cover caps using the packed in 13 mm box spanner E The transport bolts must always be removed before using the washing machine for the first time and must be retained for any subsequent transport e g when moving Remove the Insert the transport bolts cover caps Do not remove these hose holders e Connection on the left side Power Supply Optimum Water Pressure 30kpa 800kpa 220 240V 50Hz Use cold water from the tap SRHERIONE Water Supply Hose max 100 cm min 60 cm Water Drain Hose Approx 105 cm e Connection on the right side Power Supply 220 240V 50Hz Power Cord Water Supply Hose max 100 cm min 60 cm Water Drain Hose Approx 160 cm 25 3WPLO090501 How to Install the Washing Machine Connecting the e Water supply hose water supply E Optimum water pressure is 0 03 0 8MPa Do not connect to the mixer tap of an unpressurised hot water apparatus E Use a horizontal tap Horizontal tap E mse Square RI Connect the water supply hose to the rear panel of the washing machine Make sure that the rubber seal is inside the hose connector Hose connector Rubber seal Model with SCREW TYPE water supply hose Firmly connect the water supply hose to the tap and check connection points for water tightness
20. ectrical appliances nearby such as a TV a radio etc e The motor may be locked due to overload the clothes being trapped in the rubber seal etc Rubber parts may give off a smell when you first start using the washing machine There may be mold dirt or detergent residue on the drum You may have used too little detergent You may have poured detergent directly into the drum The transport bolts may not have been removed The washing machine may be installed on a sloping or unstable surface There may be foreign objects inside the drum This is normal There may be noise when the drain pump is on This is normal Liquid is inside the 4 Ply Liquid Load Balancer fixed onto the drum to make it balanced This is normal Tapping sound is generated when laundry touches to the laundry protection bulge on the laundry inlet In some environmental or usage conditions Detergent dispenser may get wet due to condensation There may be drops of water or condensation in the washing machine due to the factory inspection prior to shipment e Use the appropriate amount of detergent Do not pour in more than the max level of softener Firmly set the softener cover on the detergent dispenser e Use the appropriate amount of detergent Wipe the water away before adding detergent Unplug the power cord and plug in again Then select a program and start Do no
21. fore operating the washing machine please read these safety instructions carefully l Issues which could cause death or serious injury E Do not dismantle repair or modify the appliance l General safety gt This could cause malfunction fire electric shock or injury gt For repair please contact your local service center E Do not put fire sources or anything inflammable in or near the washing machine gas diesel petrol thinner alcohol or clothes stained with these substances gt This could cause an explosion or fire E Do not pour water on the machine when it is running gt This could cause an electric shock E Do not climb on the washing machine gt This may cause injury E Do not put heavy objects on the washing machine gt This may damage the surface of the worktop E It is a malfunction if the drum is still rotating when the door is open In this case never touch the drum nor laundry inside and stop using the washing machine immediately and contact your local service center for repair E This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction on how to use the appliance safely i E The installation of the appliance should be done by the manufacturer s l Installation dealer or service agent l gt If the installation test run and inspection of the appli
22. g machine with a soft cloth Do not use of the washing solvents such as alcohol or benzine machine E Descaling The water in some areas is hard and contains lime so it is recommended to use a water softening agent periodically or use a descaler according to the descaler manufacturer instructions Do this separately from any laundry washing E After each wash Leave the door open for a while to dry the drum This helps to prevent the growth of mold and stagnant smells forming inside the washing machine E Maintenance wash It is recommended to run the Tub Clean program regularly Using this program keeps the drum clean and prevents the growth of mold 20 3WPLO090501 Troubleshooting w Door cannot be opened Buttons do not work Water is not supplied Displayed remaining time changes There s no foam or hardly any foam There s a lot of foam Detergent in the dispenser lj is not washed away Rinsing begins before spinning finishes The drum stops and rotates repeatedly during spin Spin cycle repeatedly starts and stops There is still some water in the washing machine Child lock may be activated Washing machine may be switched off before the door lock is released Child lock may be activated Settings cannot be changed while a program is in progress The water tap may not be turned on The water supply hose may be frozen The water supply hose may be kinked or pinched
23. iated parts Risk of choking on plastic film and collapsible boxes Disposing of your Old appliances are not worthless rubbish Environment conscious _ old appliance recycling can reclaim valuable new materials A Danger of death Unplug mains plug on redundant appliances Cut off mains cable and discard with mains plug E Destroy the lock on the door To prevent playing children from being trapped and endangered ensure that the door locking mechanism is 7 disabled If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal 7 Hints and Tips for Eco Friendly Washing E Keep to the load limit of each program E Your washing machine automatically adjusts the operating time and amount of water of each program depending on the load E You only need to use the Prewash or Intensive options if your laundry is heavily soiled E Add detergent according to the degree of soiling laundry size and water hardness and follow the detergent manufacturer s instructions E Using the Cotton program with water temperature at 60 C setting z instead of the Cotton program with water temperature at 90 C will save energy and will remove ordinary stains Better still in areas where the temperature is high you can remove ordinary stains without using hot water by setting Cold programs for more economically friendly a operation 3WPLO090501 Safety Instructions Be
24. lastic base plate VITTTTTTTITITTTTTT ATT Adjustable leg is not over 25 mm 28 3WPLO090501 How to Install the Washing Machine Under counter E You need a space of 600 mm W x 600 mm D x 850 mm H with at installation least 3 mm of clearance on the sides above and back E If the height of the space ranges from 823 mm to 852 mm use upper plate sold separately z Upper Plate Part No BD W80MV 150 E Please contact your local dealer when installing the upper plate Necessary clearance Above At least 3 mm Back At least 3 mm Sides At least 3 mm E For neater installation under the counter check the height of internal measurement before fitting and adjust to the appropriate height with the adjustable feet gt Page 28 How to Install the Washing Machine Level Adjustment 29 3WPL090501 How to Install the Washing Machine Checking after installation Before the first wash 30 3WPLO90501 1 Turn on the water tap and close the washing machine door 2 Press the Power button to switch power on 3 Select the Cotton program and press the Start Pause button 4 After 5 minutes check if there is no water leakage from anywhere 5 Press the Power button to switch power off 6 Press the Power button again to switch power on 7 Select the Spin program and press the Start Pause button 8 Check if there is no abnormal vibration or sound and that water is drained out properly
25. ms in a laundry net e You may be washing too many large items such as bed sheets The washing machine may be installed on a slanting floor or may not be level e You may be washing waterproof or antislip treated items gt Page 9 Before You Start Washing Sorting the laundry The door may be open The door may not be closed completely Laundry may be exceeded 8 5 kg and door is pushed from inside There may be other appliances that generate electrical noise near the washing machine The drain hose may not be set correctly There may be too much foam in the drum Laundry may exceed rated capacity e Drain hose end is set lower than 60 cm Check water tap water inlet filter water line and water hose Check drain hose drain pump and drain outlet If C02 still appears after removing the possible cause please contact your local service center for repair Add a few clothes to the drum Spinning only one item may result in imbalance Check the door and close firmly Switch power off and press the door to close tightly Hold that position and switch power on and wait until the door lock is released Move the appliances away from the washing machine Same as in C02 See page 16 for max load of each program See page 25 for proper height on drain hose setting 23 3WPLO090501 How to Install the Washing Machine Safety E The washing machine is heavy Use cautio
26. n 1 kg of down or synthetic material polyester Do not wash duvets stuffed with wool or duvets with a silk covering Do not add other items in the same wash e Washable Blankets Synthetic or woolen blankets weighing not more than 2 5 kg Do not wash pure woolen long pile or electric blankets Other Items Bed pads and curtains weighing not more than 2 5 kg E Use this program separately from any washing program 1 Press the Power button to switch power on 2 Select the Tub Clean program 3 Press the Start Pause button 4 The Remaining Time indicator shows and starts blinking and stops blinking after 1 2 minutes Then press the Start Pause button to pause the program 5 Open the door and add the tub cleaner directly to the drum Do not use detergent for washing clothes 6 Close the door and press the Start Pause button to restart the program Your washing machine features Intelligent Sensor Systems that detect laundry size fabric type and water temperature and then control the method of washing to maximize energy and water saving When the Cotton course with the Cold water setting symbol is shown on the display is selected after laundry size fabric type and water temperature are detected the optimum amount of water wash rinse spin times spin speed and number of rinses are determined for eco friendly operation Water Amount of water Temperature Wash time x Y 4 Rinse time z Spin time
27. n when lifting it Instructions E When lifting the washing machine do not hold the jog dial or the detergent dispenser casing Lift the washing machine with two persons holding the bottom and the back of the washing machine E Frozen hoses may tear burst Do not install the washing machine in areas where there is a risk of freezing or outdoors E f the power supply plug is damaged in order to avoid hazard it must only be replaced by an authorized service agent or repair shop appointed by the manufacturer E Make sure to earth the unit Failure to earth the unit may cause electric shock if an electric leak takes place l Dimensions W 600 mm D 624 mm e D 600 mm _ piace C J Eom E 3 p Cas H 850 mm h 820 mm r A SS J ay Me e Height without worktop for under counter installation Where to install E Install the appliance on a flat hard floor to avoid excessive vibration and the washing noise machine E Do not install the unit in humid places such as a bathroom or places that are exposed to wind and rain E Keep the minimum installation distance from the walls to prevent abnormal sound and vibration Back At least 3 mm Side At least 3 mm Side At least 3 mm 24 3WPL090501 How to Install the Washing Machine w wu Removing the transport bolts Hose and cabl
28. on 1 Power button Seat A Start Pause button oga Jog Dial Teal El Temperature button SSS Mee oeton f rewash button Intensive button I 8 Extra Rinse button g Rinse Hold button Child Lock E Timer button 11 Memory button LED multi function display iH Auto Self Clean button N Press this button to switch power on and off If no program is selected or no button is pressed for 10 minutes the washing machine automatically switches itself off Press this button to start or pause a program When the machine is paused for over 1 hour the washing machine automatically switches itself off Turn this dial to select wash programs Enables temperature setting from cold up to 90 C When you select cold the symbol is shown on the display and the heater switches off Enables spin speed setting from 0 No Spin to 1200r min No Spin display The intermediate and final spinning are cancelled and the water is drained out only Recommended for delicate fabrics Prewashes heavily soiled items before the main wash The jy symbol is shown on the display Pour the powdered detergent into the dispenser Uj Extends the washing time for more thorough washing The a symbol is shown on the display This gives washing an extra rinse Recommended for areas with very hard water when washing baby linen and for people concerning about detergent residue The
29. ou Start Washing e Preparation of E Remove any foreign objects coins safety pins etc the washing E Use a washing net when you wash delicate clothes knit products lingerie etc E Close zips brush sand out of pockets and collars E Brush pet hair out of laundries E Sort the laundry according to the type of fabric and care label symbol Sorting the cottons mixed fibers synthetics wool hand wash etc laundry E Do not wash too small amount of laundry such as only a pair of jeans gt This may result in insufficient spin performance E Separate colored and white items A Risk of injury Washing the following items may cause injury or malfunction due to abnormal vibration Waterproof items such as a wet suit ski suit etc Anti slip treated items with rubber bottoms such as a doormat Cushions pillows shoes etc 3WPLO090501 Before You Start Washing Detergent and E Use the amount of detergent recommended on the detergent package additives The type and amount of detergent depends on the type of fabric load size degree of soiling and hardness of the water used Use less detergent if you wash a small load the laundry is slightly soiled E Too much detergent can result in excess foam formation which reduces rinse efficiency or may cause a water leak E Depending on the detergent brand detergent may remain undissolved when the water pressure is low or when the water temperature is low
30. rewash Intensive ExtraRinse RinseHold Auto Self Clean Child Lock Press 3 Sec E Sort the laundry according to type of fabric care label symbol color and degree of soiling gt Page 9 Preparation of the washing E Do not exceed the maximum load E Close the door Take care not to trap any items of clothing between the door and rubber seal E f no program is selected or no button is pressed for 10 minutes the washing machine automatically switches itself off Press the Power button again to turn power on E Select a washing program first with the Jog Dial E The duration of the selected program is shown on the display as a guide Actual washing time may vary depending on the conditions E Use the option buttons to set additional functions gt Page 7 Control Panel and Display gt Page 16 Program Overview E f you select the wrong program by mistake reselect the washing program by turning the Jog Dial E When the Cotton program is selected settings such as spin speed additional options etc are memorized Same settings can be used when the Cotton program is selected again E The detergent and any additives must be placed in the appropriate into the detergent eed dispenser Press the Start Pause button Page 6 Product Descriptions Detergent Dispenser E Add the appropriate amount of detergent suggested in the manufacturers instructions gt Page 10 Detergent and additives
31. se Hold This program is tested and approved by Aller 6 400 1200r min Bat tt are bea F Daily 60 6 kg 30 60 C No Spin Rinse Hold For washing lightly soiled items in just 60 mint 400 1200r min a f Rinse amp Spin 8 5 kg No Spin Rinse Hold For rinsing and spin drying only recommende Spin 8 5 kg 400 1200r min Use to spin dry hand washed items or after u Drain 7 p 7 For emptying out water remaining after the las program with the Rinse Hold option Tub Clean 7 40 C 800r min A special cycle that cleans the inside of the wa cycle regularly keeps the tub clean and preven Crease Care 4kg 30 60 C AUO Bonin Gentle spin and increased water for easily wrin No Spin Rinse Hold WOOLMARK manufacturer of this washing machine M1241 APPAREL CARE The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of machine washable wool products provided that the products are washed according to the instructions on the garment label and those issued by the Cotton Eco program cycle is the recommended program cycle for a normal soiled load at the rated capacity 16 3WPLO90501 am Overview Selectable Options aundry Notes wW r J ed Auto Prewash Intensive Extra Rinse Rinse Hold Timer Self Clean an items such as shirts underwear 7 g 5 a ration that saves energy and water that o 5 5 5 o z nance as the Cotton program ghtly soiled clo
32. t hose Clean the water inlet filter See page 20 This is not a malfunction e Use the appropriate amount of detergent This is not a malfunction e Use the appropriate amount of detergent e Use the appropriate amount of detergent f you are using prewash push the Prewash button This is not a malfunction This is not a malfunction Add one or two bath towels to the drum 21 3WPLO090501 Troubleshooting E E Foam remains on the door or the door seal Fabric softener overflows Fabric softener remains There s detergent powder residue in the detergent dispenser The washing machine switches off during operation Odor in the washing machine Unsatisfactory washing results Unusual noise or vibration Noise during drain cycle There s the sound of water when the drum is rotated manually Tapping noise comes out at spin start Detergent dispenser is wet Water remains in washing machine before initial use 22 3WPL090501 e You may have used too much detergent e Laundry is new or not that soiled e You may have exceeded the max level of softener in the detergent dispenser amp e The softener cover may have come out e You may have used too much detergent e You may have poured detergent in the detergent dispenser when it was wet Wipe the water away before adding detergent There may be noise from other el
33. t place electrical appliances close to the washing machine This is not a malfunction Wait for about one hour and restart the program The smell goes away over time e Run the Tub Clean program e Use the appropriate amount of detergent Pour detergent in the appropriate dispenser Remove the transport bolts before using Install the washing machine on a horizontal stable surface Remove foreign objects such as coins pins etc from the drum This is not a malfunction This is not a malfunction This is not a malfunction This is not a malfunction This is not a malfunction Error Codes code peseription f Possisie cause f souton C01 Water is not supplied C02 Water is not drained C04 Spin cycle does not function C08 Door lock does not function C09 Door unlock does not function C14 Malfunction of vibration sensor C18 Spin cycle does not function C19 Overloaded C30 Water flows out from drain hose while washing Water tap may not be turned on Water inlet filter may be clogged Water line or water hose may be frozen Water supply may be cut off Drain hose or drain pump may be clogged Drain hose may be kinked or frozen Drain hose may not be set correctly Height of the drain outlet may be too high e Clothes may be imbalanced in the drum e You may be washing only one heavy item such as a cotton blanket or jeans or small ite
34. t This may cause deformation of the machine 3WPLO090501 Product Descriptions Detergent Dispenser Softener Cap Dispenser For fabric softener Dispenser wW For prewash Dispenser w For main wash Door Handle Emergency Door Lock Release Drain Hose Control Panel Door Lock Power Cord Drain Tube Ge P Drain Filter 6 Fiter Gover x Adjustable Feet 4 pcs Packed In Accessories Either type of water supply hose is packed in by area demand Water Supply Hose amp Water Supply Hose One touch Joint Screw Type Hose Guide Spanner 1 piece 1 piece Cover Caps 4 pieces Optional Accessories Upper Plate See page 29 Part No BD W80MV 150 Water Leak Detection Hose O Part No BD W80MV 162 Please contact your local dealer when installing the upper plate and the water leak detection hose 3WPLO90501 Control Panel and Display o Catton Mi je Care 0 ix rgy Care 0 o Daily 60 o o Rapid 15 fub Clean o Synthetic Rinse amp Spin o Delicate Spin o o Duvet Drain o Cotton Eco ee ee 1 Power button A Start Pause button Eog Dial 4 Temperature button 5 Spin button g Prewash button Intensive button 8 Extra Rinse button 9 Rinse Hold button Child Lock 10 Timer button Memory butt
35. thes and small items t s also ideal for freshening up just worn fo s 3 Shirts etc made of polyester acrylic 0 z 5 g 6 a together with different types of laundry O O a e fo 0 ems such as lingerie and thin lace 7 7 a o 5 clothes jeans sportswear etc Oo 0 fe O fe 0 luvets blankets bedspreads etc O O 0 ible woolens bearing the Woolmark Z O fe 0 3d by Woolmark dust mites mold and bacteria 3d by Allergy UK k 2 H Q 9 2 ust 60 minutes fe commended for hand washed items 0 0 0 or after using Rinse Hold after the last rinse when using a 7 k E i ji e of the washing machine Using this 7 7 7 7 i and prevents the growth of mold easily wrinkled fabrics 0 fe fe 0 0 fe 4Allerey The Allergy Care program was awarded the Seal of Approval by Allergy UK By reducing gt i e mold house dust mites and bacteria this program provides worry free washing for people with delicate skin and families with a baby The Allergy Care program was tested and approved under the following settings Washing temperature of 90 C No options added 17 3WPLO090501 In Case of Emergency In the event of a power outage Emergency door release 18 3WPLO090501 The washing machine features a Fully Auto Restart function If the power is shut off part way through a wash the cycle wash rinse spin at the time is memorized
Download Pdf Manuals
Related Search