Haier ES10V-M1 Water Heater User Manual
Contents
1. 2 Packing list ood ES10V M1 ES10V M2 ES15V M1 M2 Electric water ES25V M1 ES25V M2 ES35V M1 ES35V M2 Haier Safety valve Drain hose Expansion hook PCS User s manual Connecting line PCS 0040502334 V Safety warning Read carefully before use O O Check if the ammeter and the diameter of the wires are in accordance with the rated current of the water heater If necessary please have it checked by an experienced electrician This water heater is available for AC 230V 50Hz power Be sure to use independent socket and earth it reliably and socket quality shall conform to the national standard requirements Set the power socket of the water heater at the dry position away from spraying water Do not plug unplug with wet hands After installation be sure to fill the heater completely with water before switching on the power in the first usage Children must take a bath under the supervision of adult In opening and closing the water valve do not point the showerhead toward the human body Otherwise it may hurt by the spraying hot water During winter in a cold area if the heater is idle for a long period please pull the handle of the safety valve to discharge the water Otherwise it may freeze inside the water heater and cause damage o0 o0o080o0 In case the power cord of the water heater is damaged be sure to have it replaced by after se2. Multiple usage Enclosed structure capable of supplying water to multiple places like toilet kitchen etc Suitable for family enterprises service trades like beauty care on hot water supply not drinkable Technical data e Packing list ii Parameters item ___ UnitjES10V M1 M2 ES15V M1 M2 ES25V M1 M2ES35V M1 M2 Rated voltage v 230 20 20 20 newie o 8s 0o u 6 No less than No less than No less than No less than E Ae coe Average temperature of hot C water outlet Re heating time 3x1 5 3x1 5 Remarks The permitted error limit of net weight above is 10 A Dimensions Figure 1 Model ES10V M1 M2 298mm _ 28 mm 501mm_ 152mm 100mm ES15V M1 M2 318mm 300mm 623mm 152mm 100mm ES25V M1 M2 378mm _ 3 4mm_ 6l6mm 152mm 100mm ES35V M1 M2 415mm _ 405mm 663mm 152mm 100mm _ A Hot water outlet B Cold water inlet CTank D Heating element E Anode rod F Thermometer tube G Wall mounting bracket H Temperature regulating knob Remarks 1 The permitted error limit of the above parameters is 10 2 The thermoter is not a precision temperature meter The dial is divided into three zones which are blue croci and red only representing the water temperature of the heater tank from low to high 6
3. water heater dry To ensure high working efficiency heating elements and tank liner of water heater shall be cleaned once every three years Take care not to damage the protection layer on heating elements and tank liner surface According to the local water quality magnesium rod shall be periodically replaced If maintenance is needed please contact a local service station N Only cold water but pointer light when heat Only cold water and pointer not lit when heated Heating pointer always lit Confirmation items 1 No water supply or water pressure too low ma W intis blocked or h ater use point is blocked or hot ia Check and clear water valve is closed Hot water access close Check and open Temperature not set to desired p Adjust the temperature of water setting Heating time limit and settin J J Keep heating temperature not obtained Contact with service department when 1 and are excluded 4 Defective heater Check power socket Contact with service department when Q is excluded Setting water temperature not Uncontrollable thermostat Contact with service department when C is excluded No power to heater 2 Uncontrollable thermostat Inconstant flow and temperature of water Insufficient hot Adjust the flux of outlet water or use with constant water pressure 1 Temperature set too low Adjust setting water temperature Inconstant water pressure
4. 5 5 The safety valve should be connected to the water inlet pipe Please check carefully if the direction is correct after installation The correct direction of installation is that the arrowhead on the safety valve should point to the water heater Please connect the drain hose to the safety valve Connect one end of the hose to the safety valve vent and the other end to the sewage drain for fear of indoor contamination The hose can be cut short or extended as necessary The hose shall be installed as inclined downward The heater should work with the safety valve whose rated pressure is 0 80MPa During heating water may drip from the drain hose of the pressure relief hole due to expansion and the hole must be left open to the atmosphere Check safety valve once a month as follows move the small handle of the safety valve if there is water flowing out the safety valve is normal if there is no water flow please contact local after sales service station The pressure relief hole is to be operated regularly to remove lime deposits and to verify that it is not blocked A Attention during installation Q oO oO Please fasten the drain hose to the pressure relief hole of the safety valve by twisting see to Figure 4 Connect the other end of drain hose to the sewer to avoid polluting the room by splashing When the power is switched on and the water heater starts operating there may be some water discharged from the pressure re
5. ection lines among the accessories into the hook tightening end and assemble the hook well Afterwards insert and fix two hooks into the holes wherein the hook with connection lines is fixed in the right hole Lift the water heater and hang it with wall rack corresponding to the two hooks insert the connection spacer led from the rear shell wall rack of the heater into the connection terminal of the line on the hook See Figure 2 Install accessories such as safety valve as shown in Figure 3 Do use sealing compound to prevent water leakage To facilitate installation and removal it is suggested a G1 2 movable nut be fitted at appropriate locations on inlet and outlet pipes respectively Find the location requiring hot water supply Connect inlet pipe outlet pipe and city water pipe respectively to the use point for hot water Note The hot water pipe shall not be too long to reduce heat losses Please reserve some space in installation for the future maintenance 2 Expansion Wall rack Figure 3 for installation reference only Hot water outlet Safety valve hook In tr Cold water inlet Cold water F igure 2 Hotwater Sneve Shower head Extended connection line outletvalve Mixing valve A Connection and use of safety valve oO oO 5
6. lief hole of the safety valve It is due to the water expansion under heating and is anormal phenomenon The pressure relief pipe shall communicate with the air directly Do not block it The drain hose connecting to the safety valve shall be kept downward sloping in installation and in a frost free environment Be sure to check and confirm that the tank is filled with water there is no leakage at each joint and the power supply complies with the stipulation before switching on the power C 6 Connect This heater must be equipped with the safety valve along to drain W hose with the machine otherwise any safety accident and property loss caused thereby shall be the user s own responsibility Figure 4 A Safety precautions 5 O Do not confuse the water inlet and outlet pipes The wall bearing the water heater shall be strong enough to endure a weight twice as much as that of a water heater filled with water Do not secure it by means of adhesive or similar products because the fixation by such methods is unreliable 3 Nice molding space saving Vertical type wall mounting design saving space The water heater you purchased is the improved model of the series product Please operate according to the user s manual Cleaning and maintenance Disconnect power supply before cleaning Gently wipe with wet cloth dipped with a little mild detergent Do not use gasoline or other solvents Finally dry with a dry cloth Keep
7. rvice technicians with the special cord offered by the manufacturer Do not set at place that is too cold and may freeze Do not set at outdoor places Do not use as floor standing appliances Please mount it to firm and reliable wall Do not install to places without sewage Connect the drain hose to the inlet of the sewer to avoid polluting by splashing Never do that Be sure to act as per instructions The product adopts the patented Safe Care technology of our company As long as product adopts civil power supply even if the earthing wire is electrified by mistake the Safe Care technology still can block dangerous electricity and ensure your personal safety But if you find any perceptible current please disconnect the power and contact after service department for maintenance Do not disassemble by yourself The original pipeline of the water heater is an organic part of Safe Care Do not remove it by yourself Otherwise we will not take responsibility for injury and loss caused by the safety danger occurring Haier Spa Water Heater User s Manual ES10V M1 ES15V M1 ES25V M1 ES35V M1 ES10V M2 ES15V M2 ES25V M2 ES35V M2 Haier Please read this manual before usage Retain it for future reference O Pre safe Expert This mark is the designation for Pre safe Expert of Haier Water Heater Company which indicates the use of the company s patented technology inside the prod
8. temperature automatically The power will be switched off automatically when the set temperature is reached and will be switched on automatically when the temperature drops to a certain level As it continues heating you can use hot water as well When the tap water inlet pressure arrives at or exceeds 0 80MPa the drain hose of safety valve will discharge a large amount of water It is due to extra high water pressure Please contact the local after service agent for disposal In long term out of use or maintenance of the heater you can close the city water pipe valve and set the mixing valve to the highest water temperature rate after opening the safety valve handle Move up the safety valve handle to drain the tank To avoid injury before the next use it is suggested to first open hot water valve before switching on the water heater exhaust gas possibly retained in the pipeline In this case no smoke or fire is permitted near the open valve Carefully check and confirm all parts are in good condition Safety High quality heatproof stainless steel electric heating element over temperature protection overpressure protection of tank safe and reliable The third generation Safe Care design for safer usage Durability Full plastic shell handsome and durable Enamel tank with reliable quality and long operation life Convenience Adjustable water temperature water inlet adjusting range actual temperature 75 C
9. uct It ensures you a safe bath while monitoring whether your house ground wire is live or not all the time If this mark is lit it indicates your house ground wire was come live poor grounding and live In this case please immediately stop use and disconnect the power and remember not to touch any electric appliance in your house At the same time immediately contact after sales service and your property management company for professional repair until the mark goes off Pre safe Expert will become the electric safeguard for your family f a PTO 0 Mark of Haier Safe Water Heater See to the physical for the appearance color or pattem fe Electric circuit diagram MT gt rF BT L Live wire brown N Null line blue MT High temperature limiter EH ib BT Thermostat i Oe Dies ae HL Heating indicator NT gt EH Heating element gt E Grounding wire yellow green E Installation e Usage i Installation Installation must be made by installers of or designated by our company after service department The water heater shall be wall mounted Make 2 holes 12mm 65mm deep in wall with an impact drill according to the drawing of the external dimensions Take out all accessories in packaging liner unpack one hook sleeve the ring end of the conn
10. water 2 Excessive water pressure Adjust the flux of outlet water To avoid danger caused by accidental resetting of the heating breaker the power for the heat cannot be supplied by timer and other external switch devices or connected to circuit with frequent switching for facility use If any part is damaged please contact the local maintenance agent and have it replaced with our spare parts Tap water inlet pressure shall be no less than 0 05MPa and the maximum pressure shall not exceed 0 75MPa ies Usage After installation as the tank is empty in the first usage be sure to open the tap water inlet valve and turn to the top temperature button on the mixing valve When the tank is filled with water and the shower nozzle or other water outlet keeps the water output please close the mixing valve check if there is water leakage at each joint and plug the power Turn the knob as per the needed water temperature The setting temperature rises gradually when the temperature regulating knob is rotated clockwise when setting to the maximum temperature the knob cannot be rotated any more the temperature decreases gradually in case of anticlockwise rotation of the knob The mark of the knob increases from the actual temperature to 75 C You can set the heating temperature steplessly The heating indicator will light on under heating mode Generally the knob should be set to the highest scale The water heater can regulate the
Download Pdf Manuals
Related Search