Haier AS072XHERA Air Conditioner User Manual
Contents
1. Heat preservation pipe Connecting pipes Drainage pipes REMOTE CONTROLLER B Parts and Functions OOG 90G Power ON OFF Used for unit start and stop MODE Used to select AUTO run COOL DRY HEAT and FAN operation CLOCK Used to set correct time TIMER Used to select TIMER ON TIMER OFF TIMER ON OFF LOCK Used to lock buttons and LCD display RESET Used to reset the controller back to normal condition HOUR Used to set clock and timer setting SLEEP Used to select sleep mode SET Used to confirm Timer and Clock setting LIGHT Control the light up and go out of the control panel s background light source and control the switch of the buzzer HEALTH Used to set Health operation function Used to select fan speed AUTO LOW FAN MED FAN HIGH FAN 3SWING Used to set UP DOWN air sending and RIGHT LEFT air sending direction TEMP Used to set temp temp 16 30 3 Timer ON OFF display Fan speed and air sending direction display LOW MID HIGH AUTO Swing direction display Room temperature display Sleep state display GO Health display Display when set Health operation function Electric Heating display Fresh Air state display Battery Capacity display Display when the electric power of the battery is insufficient Lock state display 5 Temperature d2. and pull it out on the front side then connect them 3 Coat the flaring seal face with refrigerant oil and connect pipes Cover the connection part with heat insulation materials closely and make sure fixing with adhesive tape Wall hole 70mm Thickness of wall Section of wall hole Piping hole pipe 26 B Instructions to installation Heat insulation material Lid for right piping Lid for under piping Indoor outdoor electric cable Lid for left piping Change for fresh air tube Indoor outdoor electric cord and drain hose must Fix with adhesive tape be bound with refrigerant piping by protecting tape 7 Other direction piping Cut away with a nipper the lid for piping according to the piping direction and then bend the pipe according to the position of wall hole When bending be careful not to crash pipes Connect beforehand the indoor outdoor electric cable and then pull out the connected to the heat insulation of connecting part specially eHang surely the unit body onto the upper notches of the mounting plate Move the body from side to verify its secure fixing e In order to fix the body onto the mounting plate hold up the body aslant from the underside and then put it down perpendicularly 8 Indoor unit communication addresses setting CAUTION FAIL TO DO THIS THE UNIT WILL NOT WORK There are two methods to set the communication address A Use the remote controll
3. operation mode changes as follows Remote a an atl tl controller LOW MID HIGH AUTO Unit runs at the speed displayed on LCD When fan speed is AUTO it is changed automatically according to the indoor temperature Press ON OFF button Unit stops running Note During Auto run operation temp setting will be shown in LCD display unit will select heating cooling or fan operation according to the room temp H Operation Cooling D Press ON OFF button Unit starts running The previous status appears on the display except TIMER SLEEP mode Press MODE button For each press operation mode changes as follows Remote V bG controller AUTO COOL DRY FAN HEAT Select cooling operation Shows Cooling operation starts 8 Select temp button Press TEMP button A Every time the button is pressed temp setting increases 1 C w Every time the button is pressed temp setting decreases 1 C If the button is kept pressed setting will increase or decrease quickly RESET CODE LIGHT LOCK Press FAN button For each press fan speed changes as follows C a4 ad all auti controller LOW MID HIGH AUTO Unit runs at the speed displayed on LCD When fan speed is AUTO it is changed automatically according to the indoor temperature Press ON OFF button Unit stops running and when entry this mode for the next time it will show the previous setting 10 E Ope
4. disappears Hints After replacing batteries or a power failure happens Time setting should be reset Remote controller possesses memory function when use TIMER mode next time just Press SET button after mode selecting if timer setting is the same as previous one 16 E Operation Timer on off function Remote controller operation TIMER ON OFF 1 After unit start select your desired operation mode Operation mode will be displayed on LCD 2 TIMER mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows E EN Remote AM 12 00 12 00 12 00 pm 12 00 controller TIMERON TIMER OFF TIMER ON OFF Select your desired TIMER mide TIMER ON or TIMEROFF ON or OFF will flash 3 Timer setting for TIMER ON Press HOUR button A Every time the button is pressed time increases 1 min If button is kept pressed time will change quickly Every time the button is pressed time decreases 1 min If button is kept pressed time will change quickly Time will be shown on LCD Won HEATH ARAL It can be adjusted within 24 hours lt lt AM refers to morning and PM to afternoon 4 Time confirming for TIMER ON After time setting press TIMER button to confirm eX stops blinking while 9 starts blinking 5 Time setting for TIMER OFF Follow the same procedure in Time setting for TIMER ON 6 Time confirming for
5. the conditioner is transferred to the new user this manual should be as well transferred to the new user WARNING Don t blow the human body with the cooling air too long and don t let the room tempera ture decrease too low either Otherwise the one will feel unpleasant or harm ones health If any abnormal phenomena is found e g smell of firing please cut off the power supply immediately and contact the dealer to find out the handling method In such case to continue using the conditioner will damage the conditioner and may cause electrical shock or fire hazard When need maintenance and repairment call dealer to handle it Incorrect mainten bang 5 ance and repairment m M may cause water SY leak electrical shock S and fire hazard Please let the dealer be responsible for installing the conditioner Incorrect installation may cause water leak elec trical shock and fire hazard Don t put fingers or any other things into the inlet outlet and swing louver while the condi tioner is in operation Because the highspeed fan is very dangerous and may cause injuries Call the dealer to take measures to prevent the refrigerant from leaking If conditioner is installed in a small room be sure to take every measure in order to prevent suffoca tion accident even in case of refrigerant leakage When conditioner is deinstalled or reinstalled dealer should be responsible for
6. COOL DRY FAN HEAT Select Fan operation shows 6 Fan operation starts Press FAN button For each press fan speed changes as follows a sal alll LOW MID HIGH Unit runs at the speed displayed on LCD Press ON OFF button Unit stops running and when entering this mode for the next time it will show the previous setting Note In this mode temp can t be selected temp setting will not be shown in LCD display In Fan operation mode AUTO fan speed is not available Operation cycles are as follows LOW MID HIGH 12 Operation Heating Note For cooling only type this function is invalid D Press ON OFF button Unit starts running The previous status appears on the display except TIMER SLEEP mode Press MODE button For each press operation mode changes as follows AUTO COOL DRY FAN HEAT Select Heating operation xx appears and Heating operation starts 8 Select temp button Press TEMP button A Every time the button is pressed temp setting increases 1 V Every time the button is pressed temp setting decreases 1 If the button is kept pressed setting will increase or decrease quickly Press FAN button For each press fan speed changes as follows TI ad TI all LOW MID HIGH AUTO In heat mode warm air will blow out after a short period of time due to cold draft prevention function Press ON OFF button Unit st
7. R410A MULTI SPLIT SERIES ROOM AIR CONDITIONER WALL MOUTED TYPE INDOOR UNITS OPERATION amp INSTALLATION MANUAL AS072XHERA AS092XHERA AS122XHERA e Please read this manual carefully before using this air conditioner e Please keep this manual safely for future use No 0010577054 Bl Contents cc RE Notes fof SAIC AND ELS Operation and Maintenance 20 Instructions to installation 1 24 28 When trouble Nap Pens DO Pate VOCS nA NANA GANG a OO EB Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use please make sure it s inoperative and safe Unplug the air conditioner in order to avoid the risk of child entrapment It must be noticed that air conditioner system contains refrigerants which require specialized waste disposal The valuable materials contained in a air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question Please ensure that the pipework of your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center and contribute to environmental awareness by insisting on an appropriate anti pollution method of disposal Disposal of the packaging of your new air conditioner All the pa
8. TIMER LED flashes twice Press button SLEEP three times the address is 3 and the TIMER LED flashes three times H Use the remote controller to turn off the unit At this time the controller should be changed from ON to OFF and the unit will exit the address setting procedure the address will be memorized The LED board will always display the address of this indoor unit until the system be powered off 27 B Instructions to installation I If you want to change the address please repeat the above steps from E to G J After setting all the addresses please power off the system and then power on again Otherwise the system will not start to work K Once the addresses are successfully set please do not change it any more to avoid confusion 3 Address setting procedure when using the DIP switches SWO1 SW02 A The DIP switches SWO1 SW02 are on the indoor unit PCB B Before carrying out the address setting work the system must be powered off C Take off the front panal and the filters then take off the flaps and also the front cover disconnect the swing motor connectors from the PCB and then take out the lower part of the PCB D Change the position of DIP 1 of SW01 from OFF to ON if fail to do this the addresses set by SW02 will not work E Use SW02 to set the addresses as following DO NOT CHANGE OTHER DIP SWITCHES 5 01 SW02 INDOOR UNIT ADDRESS a 4 5 6 7 8 112 3 4 5 6 7 8 e
9. TIMER OFF After time setting press SET button to confirm 3 stops flashing Time displayed Unit start or stop at x hour x min To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears According to the Time setting sequence of TIMER ON or TIMER OFF either ON OFF or OFF ON can be achieved 17 E Operation Health amp Fresh Air operation MODE HEALTH AIRFLOW O SLEEP FRESH SWING RESET CODE LIGHT LOCK O O Health operation After turning on the unit and set the desired working mode Press the Health button the LCD will display 27 the unit begins health operation start the negative ion generation device Press the Health button again 27 displayed on the LCD disappears health operation is cancelled turn off the negative ion generation device Note When indoor fan motor does not work the unit will automatically turn off negative ion generation device About Health operation After the start of Health operation the negative ion generator will generate large amount of negative ion which can effectively balance the amount of positive amp negative ion in the air and has the bacteria killing and accelerating the dust deposition of the room to make the room air fresh and healthy 18 E Notes for safety Clean the dust filter periodically Use the fuse of required capacity Blockage of the dust filter would reduce the Never use steel wire or copper
10. an result in electric shock The installation of an earth leakage breaker is necessary depending on the established location of the unit Not installing an earth leakage breaker may result in electric shock Do not install the unit where there is a concern about leakage of combustible gas The rare event of leaked gas collecting around the unit could result in an outbreak of fire For the drain pipe follow the installation manual to insure that it allows proper drainage and thermally insulate it to prevent condensation Inadequate plumbing can result in water leakage and water damage to interior items 24 B Instructions to installation awe ZZZ Z PRECAUTION Execute proper grounding Do not connect the earth wire to a gas pipe water pipe lightening rod or a telephone ground wire Improper placement of earth wires can result in electric shock An electric leakage breaker must be installed otherwise electric shock or other accidents would occur After completion of the installation the air conditioner shall be electrified to check for electric leakage 2 Preparation for installation Installation tools 1 Screw Driver flat head wabbler triangle 8 Pipe Expander 2 Steel Saw 9 Knives 3 60mm Drill 10 Clippers 4 Inner Hexagon Spanner 11 Leakage Checker or Soap Liquid 3 Shifting Spanner 12 Measuring Tape 6 Spanner 13 Scraper or File 7 Pip
11. ckaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon All these valuable materials may be taken to a waste collecting center and used again after adequate recycling Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house Safety Instructions and Warnings Before starting the air conditioner read the information given in the User s Guide carefully The User s Guide contains very important observations relating to the assembly operation and maintenance of the air conditioner The manufacturer does not accept responsibility for any damage that may arise due to non observation of the following instructions Damaged air conditioners are not to be put into operation In case of doubt consult your supplier e Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User s Guide Installation shall be done by professional people and don t install the unit by yourself For the purpose of safety the air conditioner must be properly grounded in accordance with specifications e Always
12. contact your sales dealer The fuse or breaker often shuts down 2 Water drops off during cooling or drying operation 3 There is an irregularity in operation or abnormal sound that B Failure code TROUBLE SHOOTING FAILURE CODE TIMER LED OF INDOOR RECEIVER BOARD FLASHES TIMES POSSIBLE REASONS Faulty temperature sensor Tai Faulty temperature sensor Tc1 Faulty temperature sensor Tc2 Faulty temperature sensor Tm Faulty EEPROM on indoor unit PCB Abnormal communication between indoor and outdoor unit Indoor unit address repeated Central control address repeated Faulty indoor unit fan motor Faulty driver of indoor unit fan motor Malfunction on outdoor unit ONCE X 6 TIMES 9 TIMES 10 TIMES 11 TIMES 12 TIMES 20 TIMES Sensor disconnected or broken or at wrong position or short circuit Sensor disconnected or broken or at wrong position or short circuit Sensor disconnected or broken or at wrong position or short circuit Sensor disconnected or broken or at wrong position or short circuit Faulty indoor unit PCB Wrong connection or the wires be disconnected or wrong address setting of indoor units or faulty PCB or faulty power supply Wrong setting of indoor unit address Wrong setting of centralized control indoor unit address Fan is blocked or the terminal is disconnected from the PCB or faulty indoor unit PCB Faulty indoor unit PCB Check the outdo
13. e Cutter 14 Refrigeration 3 Accessories for installation Self contained accessories No A B C D E F Name of Non adhesive Adhesive Connecting Heat Gypsum Drain hose Parts Tape tape Hose E powder materia 4 Choose the installation place Install the indoor unit where the weight of the unit can be supported Install the indoor unit where the heat source and steam source are not close and the unit inlet and outlet are not blocked Install the indoor unit where the drainage is easy and the outdoor unit can be easily connected Install the indoor unit where its cold air and hot air can be easily sent to all the comers of the room Install the indoor unit where the power socket is near and there is sufficient space around the indoor unit 9 Install the indoor unit where there is no T V set radio set and wireless applian ce underneath and the sunlight lamp is over one meter away If the remote controller is installed on the wall the indoor unit shall be ensured to receive the signal while the sunlight lamp is on 25 B Instructions to installation 5 Method for Cutting and Expanding Pipes When the pipe is too long or the mouth is damaged the pipe needs to cut or expanded 1 cutting hose 2 Removing burr 3 Put on nut 4 Expand Hose x EN Kan NG a5 HT Expansion Size 7 ZEEE H
14. er default status in first installation B Use dip switches on the indoor unit PCB 2 Address setting procedure when using the remote controller A Set the addresses only after the successful installation of the refrigerant pipes and connecting cables and open all the stop valves B Please confirm that the indoor units and the outdoor unit in the same system use the same power source C Power on the units but put all the indoor units in the status of STANDBY D Please note that the address must be set as following Indoor unit that connect to valve A the address must be 1 Indoor unit that connect to valve B the address must be 2 Indoor unit that connect to valve C the address must be 3 E Example set unit A to address 1 Continuously press the emergency switch for about 15 seconds the buzzer will sound 4 times PI PI PI PI and then leave go of the switch At this time the indoor unit has entered the address setting procedure But the LED board is blank F Use the controller to turn on the indoor unit At this time the controller should be changed from OFF to ON and then theTIMER LED flshes once That is to say the address setting is enabled G Press the button SLEEP on the controller the times you press it stands for the address you want to set detailed as following Press button SLEEP once the address is 1 and the TIMER LED flashes once Press button SLEEP twice the address is 2 and the
15. es d Area with frequent fluctuation of voltage e g factory etc e In vehicles or ships f Kitchen with heavy oil vapour or humidity g Near to the machine emitting electric magnetic waves h Places with acid alkali vapuor e TV radio acoustic appliances etc are at least m far away to the indoor unit outdoor unit power supply wire connecting wire pipes otherwise images may be disturbed or noises be created Earthing wire should not be con nected to the gas pipe water pipe lightning rod or phone line in correct earthing may cause shock Earthing Use discharge pipe correctly to ensure efficient discharge Incorrect pipe use may cause water leaking As required take measures against heavy snow Wiring e Air conditioner should be equipped with special power supply wire Operating noise Chose the following locations a Capable of supporting air conditioner weight don t increase operating noise and vibration b Hot vapour from outdoor unit outlet and ope rating noise don t disturb neighbour e No obstacles around the outdoor unit outlet B Parts and Functions INDOOR UNIT FRONT VIEW Air inlet grille Front panel Louver LED board Signal receiver LED board peessrgpcog FEAN MERRER HEALTH LED DISPLAY PRESS HEALTH FRESH STERILIZE BUTTON INDOOR UNIT BACK VIEW i B P Mounting plate
16. isplay Used to display the set temperature Clock display Humidifying display 8 Sterilize display This function is optional STERILIZE This function is optional HEALTHAIRFLOW Used to set healthairflow CODE ABB selection For this unit please set to code A Note This model does not have the following related display and function 6367 E Operation Clock set When unit is started for the first time and after replacing batteries in remote controller clock should be adjusted as follows Press CLOCK button AM or PM flashes Press A or V to set correct time Each press will increase or decrease 1 min If the button is kept pressed time will change quickly After time setting is confirmed press SET AM and PM stop flashing while clock starts working Remote controller s operation When in use put the signal transmission head directly to the receiver hole on the indoor unit The distance between the signal transmission head and the receiver hole should be within 7m without any obsacles as well Don t throw the controller prevent it from being damaged When electronic started type fluorescent lamp or change over type fluorescent lamp or wireless telephone is installed in the room the receiver is apt to be disturbed in receiving the signal so the distance to the indoor unit should be shorter Loading of the battery Slightly press w and push down the cover Load
17. itioner Please keep the installation manual for future reference when maintenance and changing installation place After installation please use the air conditioner according to the specification in the operation manual Using Directions Adjust suitable airflow direction na KA Avoid direct sunlight and airflow Keep the proper indoor temperature Furthermore it will result in excessive consumption of electric power Too cool or hot is not good for your health Effectively use timer Using TIMER mode you can make the room temperature reach a suitable temperature when you wake up or go back home ATTENTION After finishing installation please confirm there is no refrigerant leakage 23 B Instructions to installation 1 Safety precautions Please read these Safety Precautions first then accurately execute the installation work Though the precautionary points indicated herein are divided under two headings WARNING and WARNING those points which are related to the strong possibility of an installation done in error resulting in death or serious injury are listed in the A CAUTION section However there is also a possibility of serious consequences in relationship to the points listed e inthe CAUTION section as well In either case important safety related information is indicated so by all mea
18. mbustion No inflammable spray fluid should be permitted to be placed or used near to airconditioner other wise may cause fire accidents Air conditioner should be cleaned only after power supply is cut off to keep from shock or hurt Don t clean air conditioner with water Otherwise may cause shock When use the fumigating insecticide don t open air conditioner Otherwise the poisonous chemicals may settle in air conditioner which harm the health of chemical allergic people B Safety precautions CAUTIONS ON INSTALLATION Please ask the dealer or specialist to install never try by the users themselves After the installation please be sure of the following conditions Please call dealer to install the air conditioner Incorrect installation may cause water leaking shock and fire hazard CAUTION e Air conditioner can t be installed in the envi Connect earthing wire ronment with inflammable gases because the inflammable gases near to air conditioner may cause fire hazard e Installed electrical leaking circuit breaker It easily cause electrical shock without circuit breaker Location Air conditioner should be located in well vented and easily accessible place e Air conditioner should not be located in the following places a Places with machine oils or other oil vapours b Seaside with high salt content in the air c Near to hot spring with high content of sulfide gas
19. n machine is running in emergency the set value and wind speed of temperature could not be altered meanwhile it can not operate for dehumidifying or under timing mode Test operation Test operation switch is the same as emergency switch Use this switch in the test operation when the room temperature is below 16 C do not use it in the normal operaion Continue to press the test operation swich for more than 5 seconds after you hear the Pi sound twice release your finger from the switch the cooling operation starts with the air flow speed Hi Removal of the restriction of emergency or test operation Press the emergency operation switch once more or manipulate through the remote controller the Pi sound the emergency or test operation is stopped When the remote controller is manipulated it gets the system back to the normal operation mode Disconnect power supply before clean the unit Don t touch it with wet hand Don t wash with hot water or solvent to clean the unit Air filter and outdoor cleaning 1 Open the inlet grill 2 Detach the Air filters 3 Use water or vacuum cleaner to clean it If it is extremely dirty wash it with neutral detergent or soap water 4 Wash it with clean water and install it after complete dry 5 Close the inlet grill Caution Do not use hot water over 40 C as this may cause damage to air filter Wipe air filter carefully Clean it with warm and wet cloth or with neutral deterge
20. ng standard 5 The power cable and connecting cable are self provided The requirement of the connecting cable Connecting cable sheilded wire 5072 AS092XHERA AS122XHERA HOSRN F 3G 2 5mm HOSRN F 2X1 5mm All the cables shall have got the Local authentication certificate 6 The breaker of the air conditioner should be all pole switch and the distance between its two contacts should be no less than 3mm Such means for disconnection must be incorporation in the fixed wiring 7 The waste battery shall be disposed properly 8 The indoor unit installation height is at least 2m 9 The appliance is not intended for ase young children or infirm persons without super vision 10 Young children should be super vised to ensure that they do not play with the applience Safety precautions Carefully read the following information in order to operate the air conditioner correctly Below are listed three kinds of Safety Cautions and Suggestions WARNING Incorrect operations may result in severe consequences of death or serious injuries CAUTION Incorrect operations may result in injuries or machine damages in some cases may cause serious consequences INSTRUCTIONS These information can ensure the correct operation of the machine Be sure to conform with the following important Safety Cautions The Safety Cautions should be at hand so that they can be checked at any time when needed If
21. ning The Sleep function is invalid 15 E Operation Timer on off operation Remote control unit TIMER operation Set Clock correctly before starting Timer operation refer to page 2 You can let unit start or stop automatically at following times Before you wake up in the morning or get back from outside or after you fall asleep at night TIMER ON OFF 1 After unit start select your desired operation mode Operation mode will be displayed on LCD 2 TIMER mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows i gt EN Ed Remote AM 12 00 pm 12 00 AM 12 00 pm 12 00 controller TIMER ON TIMER OFF TIMER ON OFF Select your desired TIMER mide TIMER ON or TIMEROFF ON or OFF will flash 3 Timer setting Press HOUR V button A Every time the button is pressed time increases 1 min If button is kept Oa pressed time will change quickly 2 C Car v Every time the button is pressed time decreases 1 min If button is kept pressed time will change quickly Time will be shown on LCD It can be adjusted within 24 hours 4 Confirming your setting After setting correct time press SET button to confirm PIN or PIG stops flashing Time displayed Unit starts or stops at x hour x min TIMER ON or TIMER OFF Timer mode indicator on indoor unit lights up To cancel TIMER mode Just press TIMER button several times until TIMER mode
22. ns properly observe all that is mentioned AN WARNING This system should be applied to places as office restaurant residence and the like Application to inferior environment such as engineering shop could cause equipment malfunction Please entrust installation to either the company which sold you the equipment or to a professional contractor Defects from improper installations can be the cause of water leakage electric shocks and fires Execute the installation accurately based on following the installation manual Again improper installations can result in water leakage electric shocks and fires When a large air conditioning system is installed to a small room it is necessary to have a prior planned countermeasure for the rare case of a refrigerant leakage to prevent the exceeding of threshold concentration In regards to preparing this countermeasure consult with the company from which you perchased the equipment and make the installation accordingly In the rare event that a refrigerant leakage and exceeding of threshold concentration does occur there is the danger of a resultant oxygen deficiency accident For installation confirm that the installation site can sufficiently support heavy weight When strength is insufficient injury can result from a falling of the unit Execute the prescribed installation construction to prepare for earthquakes and the strong winds of typhoons and hurricanes etc Improper installa
23. nsulated Is the indoor unit fixed firmly s noise big 10 Trial operation The person who has completed this installation shall be requested to conduct a test operation for check e s the temperature adjuster working normally Does the location for installation conform to requirements Winding up with Protective Plastic Tape The connection pipes drain pipe and the connection wires shall be wound up with PVC tape Notes The connection pipes shall also be wound up with insulating material to preserve the temperature The airing direction shall be from bottom to top 28 E When trouble happens Insufficient cooling or heating The operation controller adjusted as required Air filter too dirty Any obstacle exists at the air inlet or outlet na P Door or window left opened Na 2 Horizontal swing louver upward in HEAT mode Insufficient cooling Any other heat sources in the room Sunlight direct into the room C d ji Too crowed in the room O O 207 EG Cooled air blown out when heating is audible 29 When the air conditioner does not operate properly after you have checked the above mentioned items or when following phenomenon is observed stop the operation of the air conditioner and
24. nt then wipe it dry with clean and soft cloth If air conditioner is very dirty clean it with cloth soaked in neutral detergent then wipe off the detergent with clean water Don t use insecticide or other chemical detergents 20 B Trouble shooting The followings are not malfuncition Water flowing sound is heard When the air conditoner is started when the compressor starts or stops during operation or when the air conditioner is stopped it som etimes sounds Bi Bi or Godo Godo It is the flowing sound of the refrigerant not a malfunction Cracking sound is heard This is caused by heat expansion or contra ction of plastics It smells Air blown out from the indoor unit sometimes smells The smell results from smells of furniture paint tobacco absorbed by indoor unit During operation white fog comes out of indoor unit When in COOL or DRY mode a thin water fog can be seen blown out of unit this is the condensed fog because the suddenly cooled indoor air is blown out Automatically switch into FAN mode during cooling To prevent frost from being accumulated on the indoor unit heat exchanger it sometimes auto matically switched into the FAN mode but it will soon back to the cooling mode The air conditioner cannot be restarted soon after it stops Air conditioner does not start OW This is because of the self protection function of the system
25. ops running and when entering this mode for the next time it will show the previous setting E Operation Air flow adjustment Swing louvers Vertical louvers Horizontal louvers Up and down Side from side Position 1 Position 1 Position 2 m LL Position 2 Position 3 KA Position 3 Ka Position 4 Position 4 7 Position 5 ICOOL DRY FA Position 5 N AUTO COOL HAVE NOT Position 6 Position 6 diui Position 7 NV Position 8 Fixed position Press the SWING again to fix the vertical louvers at your desired position Side from side Swing D Press SWING C the horizontal louvers move from up to down Swing Fixed position Press SWING the vertical Renee SRM louvers move from side to side Press the SWING C again to fix the horizontal louvers at your desired position Note Put louvers at up position in cooling and down position in heating mode This will be helpful to keep an even room temp Notice In cooling or dry operation don t put horizontal louvers at downward position for a long time or outlet grill might get frosted Don t expose your skin to cool or warm air for a long time 14 E Operation Remote control unit Before go to bed you can press the Sleep button the air conditioner will operate in comfor
26. or unit Note 1 Please contact the installers or distributors when trouble happens to repair it 2 Turn the power off and power on again if the failure code recurs please change the indoor unit PCB 3 Failrue codes maked with x are resumable 30 HAIER GROUP Qingdao Haier Air Conditioner Electric Co Ltd Address Haier Garden Qianwangang Road Economic Development Zone Qingdao Shandong 266500 P R China Web Site http www haier com
27. ose dia Size mm A 7 6 35 mm 1 4 0 8 1 5 Hose Expander 9 52 mm 3 8 1 0 1 5 Correct Not Correct W B i U Sg y Tilting cracks on expanded mouth burr incomplete too long 6 When the mounting plate is first fixed 1 Carry out based on the neighboring pillars or lintels a proper leveling for the plate to be fixed against the wall then temporarily fasten the plate with one steel nail 2 Make sure once more the proper level of the plate by hanging a thread with a weight from the central top of the plate then fasten securely the plate with the attachment steel nail TC a il A 80mm 3 Making a Hole on the wall and Fitting the piping Hole cover Make a hole of 60mm in diameter slightly descending to outside the wall Install piping hole cover and seal it off with putty after installation 4 Drawing of pipe Rear piping Draw pipes and the drain hose then fasten them with the adhesive tape Left Left rear piping Incase of left side piping cut away with a nipper the lid for left piping e Incase of left rear piping bend the pipes according to the piping direction to the mark of hole for left rear piping which is marked on heat insulation materials 1 Insert the drain hose into the dent of heat insulation materials of indoor unit 2 Insert the indoor outdoor electric cord from backside of indoorunit
28. ration Dry D Press ON OFF button Unit starts running The previous status appears on the display except TIMER SLEEP mode Press MODE button For each press operation mode changes as follows Remote 6 3 controller AUTO COOL DRY FAN HEAT Select Drying operation shows Dry operation starts 3 Select temp button Press TEMP button A Every time the button is pressed temp setting increases 1 C akt iUd Voix w Every time the button is pressed temp setting decreases 1 REO UAE If the button is kept pressed setting will increase or decrease quickly 4 Press FAN button For each press fan speed changes as follows Remote d alll tll controller LOW MID HIGH AUTO Unit runs at the speed displayed on LCD In DRY mode when room temp becomes 2 C lower than temp setting unit will run intermittently at LOW speed regardless of FAN setting COOL operation starts when room Press ON OFF button ig Unit stops running and when Xn isis entering this mode for the next Tempsetting time it will show the previous setting setting unitwill run in mild DRY mode 11 E Operation Fan D Press ON OFF button Unit starts running The previous status appears on the display except TIMER SLEEP mode m Press MODE button For each press operation mode changes as follows Remote F O G 3 controller AUTO
29. remember not to operate the air conditioner before opening its inlet grill B Cautions All electrical repairs must be carried out by qualified electricians Inadequate repairs may result in a major source of danger for the user of the air conditioner Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner s tubes with sharp or pointed items crushing or twisting any tubes or scraping the coatings off the surfaces If the refrigerant spurts out and gets into eyes it may result in serious eye injuries Do not obstruct or cover the ventilation grille of the air conditioner Do not put fingers or any other things into the inlet outlet and swing louver Do not allow children to play with the air conditioner In no case should children be allowed to sit on the outdoor unit Specifications The refrigerating circuit is leak proof The machine is adaptive in following situation 1 Applicable ambient temperature range DB C 27 32 18 Indoor WB C 19 23 14 Cooling outdoor WB C 24 26 20 27 weis FE I5 BC OR RR Heating Indoor 2 If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person 3 If the fuse on PC board is broken please change it with the type of T 3 15A 250VAC 4 The wiring method should be in line with the local wiri
30. table sleep mode to make your sleep more comfortable Usage of the Sleep function After starting set the Run mode and press the Sleep button Run mode 1 In cooling and dry After starting of the Sleep operation the temperature will be raised for 1 higher than the set temperature 1 hour later and be raised for 1 C after another hour It continues under that condition for 6 hours then the machine will be switched off The temperature is higher than the set temperature so as to avoid catching cold in sleeping Sleep The Sleep running starts The Sleep running stops About 6 hours Close down Set the the machine temperature In cooling and dry 2 In heating the single cooling conditioners do not have the function After the Sleep running starts the temperature will drop for 2 after another one hour The temperature will raise for 1 after hours running under the above temperature and the conditioner will be closed down after running for 3 hours The temperature is lower than the set temperature so as to avoid uneasiness in sleeping e Set the Close down temperature the machine MODE HEALTH AIRFLOW Drop for 2 C SLEEP FRESH SWING Drop for 2 C for 2 C zr tor ax About 3 hourg E ww The Sleep running starts In heating The Sleep running stops 3 In automatic running The conditioner will run under automatically selected working mode of sleeping 4 In Fan run
31. the batteries as illustrated 2 R 03 dry batteries cylinder Be sure that the loading is in line with the pole request as illustrated Put on the cover again Confirmation indicator In disorderation reload the batteries or load the new batteries after 5 mins Note The waster batteries should be disposed properly use two new same type batteries when loading If the remote controller can t function normally or doesn t work at all use a sharp pointed item to press the reset key 2R 03 dry batteries Hint Remove the batteries in case unit won t be in usage for a long period If there are any displays after taking out just need to press reset key When throw away the waste batteries please perform in accordance with the local regulation E Operation Auto Press ON OFF button Unit starts running The previous status appears on the display except TIMER SLEEP mode Press MODE button For each press operation mode changes as follows Remote 9 controller AUTO COOL DRY FAN HEAT Select Auto run won x7 appears and auto run starts Select temp button Press TEMP button A Every time the button is pressed temp setting increases 1 C W Every time the button is pressed temp reset cove UST Loox setting decreases 1 C ABBY HE If the button is kept pressed setting will increase or decrease quickly Press FAN For each press
32. them Incorrect installation may cause water leaking electrical shock and fire hazard Safety precautions CAUTIONS Conditioner should not be used for any other purpose other than airconditioning Don t use air conditioner for any other special purposes e g the preservation and protection of food animals plants pecision apparatus as well as work of art otherwise the qualities of these stuffs may be damaged Don t dismantle the outlet of the outdoor unit The exposure of fan is very dangerous which may harm human be ings heat radiator the frequent replacement of room atmosphere should be required Inefficient venti lation may cause suffocation HA After a long time use of air conditioner the base should be checked for any damages If the damaged base is not repaired the unit may fall down and cause accidents No goods or nobody is permitted to placed on or stand on outdoor unit The falling of goods and people may cause acci dents Pets and plants should not be blowed directly in the air flow Otherwise will suffer damage Don t operate the air conditioner with damp hands Otherwise will be shocked Only use correctly typed fuse May not use wire or any other materials replacing fuse otherwise may cause faults or fire accidents Don t place any burning unit in the air flow of air conditioner which may cause incomplete co
33. therefore it cannot be restarted for about three minutes after it stops Please wait for three minutes B Trouble shooting Air does not blow or the fan speed cannot be changed during drying In DRY mode when room temperature becomes 2C higher than temperature setting unit rill run intermittently at LO speed regardless of FAN setting Water or vapor generated from the outdoor unit during heating m This happens when the frost accumulated on the outdoor unit is removed during defrosting operation Defrosting operation During heating indoor fan is still running even unit is stopped To get ride of the excess heat indoor fan will continue running for a while after unit autom atically stops Please check the following things about your air conditioner before making a service call Unit fails to start Is the power supply switch on ON OFF Power supply switch is not in ON position Is city supply power normal Is the earth leakage breaker in action d Be sure to turn off the power supply switch immediately and contact the sales dealer 22 B Customer Need to know Customer Need to know Please install the air conditioner according to the requirements specified in this manual to ensure the air conditioner work well Be careful not to scratch the surface of the case during moving the air cond
34. tions can result in accidents due to a violent falling over of the unit For electrical work please see that a licensed electrician executes the work while following the safety standards related to electrical equipment and local regulations as well as the installation instructions and that only exclusive use circuits are used Insufficient power source circuit capacity and defective installation execution can be the cause of electric shocks and fires Accurately connect wiring using the proper cable and insure that the external force of the cable is not conducted to the terminal connection part through properly securing it Improper connection or securing can result in heat generation or fire Take care that wiring does not rise upward and accurately install the lid service panel Its improper installation can also result in heat generation or fire When setting up or moving the location of the air conditioner do not mix air etc or anything other than the designated refrigerant within the refrigeration cycle Rupture and injury caused by abnormal high pressure can result from such mixing Always use accessory parts and authorized parts for installation construction Using parts not authorized by this company can result in water leakage electric shock fire and refrigerant leakage e Execute proper grounding Do not connect the ground wire to a gas pipe water pipe lightning rod or a telephone ground wire Improper placement of ground wires c
35. v ON ON OFF OFF 1 ON OFF 2 12345678 ON OFF 3 4 How to check the addresses When finish all the above works please power off and power on again to the whole system but set all the indoor units in STANDBY Then continously press the emergency switch until you hear the buzzer sound 5 times Pi Pi Pi Pi Pi and then the LED board will show the address of this indoor unit Press any key on the remote controller it will exit the address checking precedure 8 Installation check and trial operation Check the Layout of the Drain Pipe and Connection Wires and also the piping and address setting The drain pipe should be placed underneath and the connection wires should be placed upside and the drain pipe especially the section inside the machine and indoors must be wound up with insulating material to preserve heat The drain pipe shall be sloped and no concave and convex shall occur along the whole pipe And the cases as the right figure indicates shall not occur 9 Installation check e Is power supply voltage required e Is water completely drained to outdoors Are power wire and connection wires between indoor and outdoor units correctly connected Is any gas leaked from the pipe connectors Are series numbers of the terminals on the indoor and outdoor units corresponding to each other Is the connection section of the auxiliary pipe i
36. wire to take cooling and heating effect consume more place of the fuse power water would be leaked during cooling and other failures would also occur j a0 e 8 Never connect the earth wire with the gas pipe Never install the air conditioner where the water pipe lightening arrester or phone line flammable gas is easily leaked Do not spray any paint or insecticide on the air conditioner 3 Q Paint PNE a g E an NO Never pour water on the indoor unit Keep the inlet and outlet of the didoor unit unblocked E When the louver is being swung never touch the Operate the unit with the remote controller outlet or put anything into the air grille The instructions with this warning mark must be carried out strictly for they are all concerned with safety of the product or human beings The instructions with this prohibiting mark must be completely forbidden otherwise the product would be damaged or the human being would be injured oe 19 Operation and Maintenance Emergency and Test Operation Emergency operation Use this operation only when the remote controller is defective or lost When the emergency operation switch is pressed Pi sound is heard once which means the start of this operation In this operation the system automatically selects the operation modes cooling or heating according to the room temperature Whe
Download Pdf Manuals
Related Search